@article{KirchnerOberlaenderFriedrichetal.2011,
  author    = {Kirchner, Patrick and Oberl{\"a}nder, Jan and Friedrich, Peter and Berger, J{\"o}rg and Suso, Henri-Pierre and Kupyna, Andriy and Keusgen, Michael and Sch{\"o}ning, Michael Josef},
  title     = {Optimisation and fabrication of a calorimetric gas sensor built up on a polyimide substrate for H2O2 monitoring},
  series = {Physica status solidi (a) : applications and material science. 208 (2011), H. 6},
  journal   = {Physica status solidi (a) : applications and material science. 208 (2011), H. 6},
  publisher = {Wiley},
  address   = {Weinheim},
  isbn      = {1862-6319},
  pages     = {1235 -- 1240},
  year      = {2011},
  language  = {en}
}
@article{KirchnerOberlaenderFriedrichetal.2010,
  author    = {Kirchner, Patrick and Oberl{\"a}nder, Jan and Friedrich, Peter and Rysstad, G. and Berger, J. and Keusgen, M. and Sch{\"o}ning, Michael Josef},
  title     = {Realization of a calorimetric gas sensor on polyimide foil for applications in aseptic food industry},
  series = {Procedia Engineering. 5 (2010)},
  journal   = {Procedia Engineering. 5 (2010)},
  isbn      = {1877-7058},
  pages     = {264 -- 267},
  year      = {2010},
  language  = {en}
}
@article{KirchnerOberlaenderFriedrichetal.2012,
  author    = {Kirchner, Patrick and Oberl{\"a}nder, Jan and Friedrich, Peter and Berger, J{\"o}rg and Rysstad, Gunnar and Sch{\"o}ning, Michael Josef and Keusgen, Michael},
  title     = {Realisation of a calorimetric gas sensor on polyimide foil for applications in aseptic food industry},
  series = {Sensors and Actuators B: Chemical},
  volume    = {170},
  journal   = {Sensors and Actuators B: Chemical},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0925-4005},
  doi       = {10.1016/j.snb.2011.01.032},
  pages     = {60 -- 66},
  year      = {2012},
  abstract  = {A calorimetric gas sensor is presented for the monitoring of vapour-phase H2O2 at elevated temperature during sterilisation processes in aseptic food industry. The sensor was built up on a flexible polyimide foil (thickness: 25 μm) that has been chosen due to its thermal stability and low thermal conductivity. The sensor set-up consists of two temperature-sensitive platinum thin-film resistances passivated by a layer of SU-8 photo resist and catalytically activated by manganese(IV) oxide. Instead of an active heating structure, the calorimetric sensor utilises the elevated temperature of the evaporated H2O2 aerosol. In an experimental test rig, the sensor has shown a sensitivity of 4.78 °C/(\%, v/v) in a H2O2 concentration range of 0\%, v/v to 8\%, v/v. Furthermore, the sensor possesses the same, unchanged sensor signal even at varied medium temperatures between 210 °C and 270 °C of the gas stream. At flow rates of the gas stream from 8 m3/h to 12 m3/h, the sensor has shown only a slightly reduced sensitivity at a low flow rate of 8 m3/h. The sensor characterisation demonstrates the suitability of the calorimetric gas sensor for monitoring the efficiency of industrial sterilisation processes.},
  language  = {en}
}