TY  - JOUR
A1  - Neu, Eugen
A1  - Janser, Frank
A1  - Khatibi, Akbar A.
A1  - Braun, Carsten
A1  - Orifici, Adrian C.
T1  - Operational Modal Analysis of a wing excited by transonic flow
JF  - Aerospace Science and Technology
N2  - Operational Modal Analysis (OMA) is a promising candidate for flutter testing and Structural Health Monitoring (SHM) of aircraft wings that are passively excited by wind loads. However, no studies have been published where OMA is tested in transonic flows, which is the dominant condition for large civil aircraft and is characterized by complex and unique aerodynamic phenomena. We use data from the HIRENASD large-scale wind tunnel experiment to automatically extract modal parameters from an ambiently excited wing operated in the transonic regime using two OMA methods: Stochastic Subspace Identification (SSI) and Frequency Domain Decomposition (FDD). The system response is evaluated based on accelerometer measurements. The excitation is investigated from surface pressure measurements. The forcing function is shown to be non-white, non-stationary and contaminated by narrow-banded transonic disturbances. All these properties violate fundamental OMA assumptions about the forcing function. Despite this, all physical modes in the investigated frequency range were successfully identified, and in addition transonic pressure waves were identified as physical modes as well. The SSI method showed superior identification capabilities for the investigated case. The investigation shows that complex transonic flows can interfere with OMA. This can make existing approaches for modal tracking unsuitable for their application to aircraft wings operated in the transonic flight regime. Approaches to separate the true physical modes from the transonic disturbances are discussed.
Y1  - 2016
U6  - http://dx.doi.org/10.1016/j.ast.2015.11.032
SN  - 1270-9638
VL  - 49
SP  - 73
EP  - 79
PB  - Elsevier
CY  - Amsterdam
ER  - 
TY  - JOUR
A1  - Hamad, E. M.
A1  - Bilatto, S. E. R.
A1  - Adly, N. Y.
A1  - Correa, D. S.
A1  - Wolfrum, B.
A1  - Schöning, Michael Josef
A1  - Offenhäusser, A.
A1  - Yakushenko, A.
T1  - Inkjet printing of UV-curable adhesive and dielectric inks for microfluidic devices
JF  - Lab on a Chip
N2  - Bonding of polymer-based microfluidics to polymer substrates still poses a challenge for Lab-On-a-Chip applications. Especially, when sensing elements are incorporated, patterned deposition of adhesives with curing at ambient conditions is required. Here, we demonstrate a fabrication method for fully printed microfluidic systems with sensing elements using inkjet and stereolithographic 3D-printing.
Y1  - 2016
U6  - http://dx.doi.org/10.1039/C5LC01195G
SN  - 1473-0189
VL  - 16
IS  - 1
SP  - 70
EP  - 74
PB  - Royal Society of Chemistry
CY  - Cambridge
ER  - 
TY  - JOUR
A1  - Murib, M. S.
A1  - Yeap, W. S.
A1  - Eurlings, Y.
A1  - Grinsven, B. van
A1  - Boyen, H.-G.
A1  - Conings, B.
A1  - Michiels, L.
A1  - Ameloot, M.
A1  - Carleer, R.
A1  - Warmer, J.
A1  - Kaul, P.
A1  - Haenen, K.
A1  - Schöning, Michael Josef
A1  - Ceuninck, W. de
A1  - Wagner, P.
T1  - Heat-transfer based characterization of DNA on synthetic sapphire chips
JF  - Sensors and Actuators B: Chemical
N2  - In this study, we show that synthetic sapphire (Al₂O₃), an established implant material, can also serve as a platform material for biosensors comparable to nanocrystalline diamond. Sapphire chips, beads, and powder were first modified with (3-aminopropyl) triethoxysilane (APTES), followed by succinic anhydride (SA), and finally single-stranded probe DNA was EDC coupled to the functionalized layer. The presence of the APTES-SA layer on sapphire powders was confirmed by thermogravimetric analyis and Fourier-transform infrared spectroscopy. Using planar sapphire chips as substrates and X-ray photoelectron spectroscopy (XPS) as surface-sensitive tool, the sequence of individual layers was analyzed with respect to their chemical state, enabling the quantification of areal densities of the involved molecular units. Fluorescence microscopy was used to demonstrate the hybridization of fluorescently tagged target DNA to the probe DNA, including denaturation- and re-hybridization experiments. Due to its high thermal conductivity, synthetic sapphire is especially suitable as a chip material for the heat-transfer method, which was employed to distinguish complementary- and non-complementary DNA duplexes containing single-nucleotide polymorphisms. These results indicate that it is possible to detect mutations electronically with a chemically resilient and electrically insulating chip material.
Y1  - 2016
U6  - http://dx.doi.org/10.1016/j.snb.2016.02.027
SN  - 0925-4005
VL  - 230
IS  - 230
SP  - 260
EP  - 271
PB  - Elsevier
CY  - Amsterdam
ER  - 
TY  - JOUR
A1  - Kowalski, Julia
A1  - Linder, Peter
A1  - Zierke, S.
A1  - Wulfen, B. van
A1  - Clemens, J.
A1  - Konstantinidis, K.
A1  - Ameres, G.
A1  - Hoffmann, R.
A1  - Mikucki, J.
A1  - Tulaczyk, S.
A1  - Funke, O.
A1  - Blandfort, D.
A1  - Espe, Clemens
A1  - Feldmann, Marco
A1  - Francke, Gero
A1  - Hiecker, S.
A1  - Plescher, Engelbert
A1  - Schöngarth, Sarah
A1  - Dachwald, Bernd
A1  - Digel, Ilya
A1  - Artmann, Gerhard
A1  - Eliseev, D.
A1  - Heinen, D.
A1  - Scholz, F.
A1  - Wiebusch, C.
A1  - Macht, S.
A1  - Bestmann, U.
A1  - Reineking, T.
A1  - Zetzsche, C.
A1  - Schill, K.
A1  - Förstner, R.
A1  - Niedermeier, H.
A1  - Szumski, A.
A1  - Eissfeller, B.
A1  - Naumann, U.
A1  - Helbing, K.
T1  - Navigation technology for exploration of glacier ice with maneuverable melting probes
JF  - Cold Regions Science and Technology
N2  - The Saturnian moon Enceladus with its extensive water bodies underneath a thick ice sheet cover is a potential candidate for extraterrestrial life. Direct exploration of such extraterrestrial aquatic ecosystems requires advanced access and sampling technologies with a high level of autonomy. A new technological approach has been developed as part of the collaborative research project Enceladus Explorer (EnEx). The concept is based upon a minimally invasive melting probe called the IceMole. The force-regulated, heater-controlled IceMole is able to travel along a curved trajectory as well as upwards. Hence, it allows maneuvers which may be necessary for obstacle avoidance or target selection. Maneuverability, however, necessitates a sophisticated on-board navigation system capable of autonomous operations. The development of such a navigational system has been the focal part of the EnEx project. The original IceMole has been further developed to include relative positioning based on in-ice attitude determination, acoustic positioning, ultrasonic obstacle and target detection integrated through a high-level sensor fusion. This paper describes the EnEx technology and discusses implications for an actual extraterrestrial mission concept.
Y1  - 2016
U6  - http://dx.doi.org/10.1016/j.coldregions.2015.11.006
SN  - 0165-232X
IS  - 123
SP  - 53
EP  - 70
PB  - Elsevier
CY  - Amsterdam
ER  - 
TY  - JOUR
A1  - Leingartner, Max
A1  - Maurer, Johannes
A1  - Ferrein, Alexander
A1  - Steinbauer, Gerald
T1  - Evaluation of Sensors and Mapping Approaches for Disasters in Tunnels
JF  - Journal of Field Robotics
N2  - Ground or aerial robots equipped with advanced sensing technologies, such as three-dimensional laser scanners and advanced mapping algorithms, are deemed useful as a supporting technology for first responders. A great deal of excellent research in the field exists, but practical applications at real disaster sites are scarce. Many projects concentrate on equipping robots with advanced capabilities, such as autonomous exploration or object manipulation. In spite of this, realistic application areas for such robots are limited to teleoperated reconnaissance or search. In this paper, we investigate how well state-of-the-art and off-the-shelf components and algorithms are suited for reconnaissance in current disaster-relief scenarios. The basic idea is to make use of some of the most common sensors and deploy some widely used algorithms in a disaster situation, and to evaluate how well the components work for these scenarios. We acquired the sensor data from two field experiments, one from a disaster-relief operation in a motorway tunnel, and one from a mapping experiment in a partly closed down motorway tunnel. Based on these data, which we make publicly available, we evaluate state-of-the-art and off-the-shelf mapping approaches. In our analysis, we integrate opinions and replies from first responders as well as from some algorithm developers on the usefulness of the data and the limitations of the deployed approaches, respectively. We discuss the lessons we learned during the two missions. These lessons are interesting for the community working in similar areas of urban search and rescue, particularly reconnaissance and search.
Y1  - 2016
U6  - http://dx.doi.org/10.1002/rob.21611
SN  - 1556-4967
VL  - 33
IS  - 8
SP  - 1037
EP  - 1057
PB  - Wiley-VCH
CY  - Weinheim
ER  - 
TY  - JOUR
A1  - Schüller, K.
A1  - Kowalski, Julia
A1  - Raback, P.
T1  - Curvilinear melting – A preliminary experimental and numerical study
JF  - International Journal of Heat and Mass Transfer
N2  - When exploring glacier ice it is often necessary to take samples or implement sensors at a certain depth underneath the glacier surface. One way of doing this is by using heated melting probes. In their common form these devices experience a straight one-dimensional downwards motion and can be modeled by standard close-contact melting theory. A recently developed melting probe however, the IceMole, achieves maneuverability by simultaneously applying a surface temperature gradient to induce a change in melting direction and controlling the effective contact-force by means of an ice screw to stabilize its change in attitude. A modeling framework for forced curvilinear melting does not exist so far and will be the content of this paper. At first, we will extend the existing theory for quasi-stationary close-contact melting to curved trajectories. We do this by introducing a rotational mode. This additional unknown in the system implies yet the need for another model closure. Within this new framework we will focus on the effect of a variable contact-force as well as different surface temperature profiles. In order to solve for melting velocity and curvature of the melting path we present both an inverse solution strategy for the analytical model, and a more general finite element framework implemented into the open source software package ELMER. Model results are discussed and compared to experimental data conducted in laboratory tests.
Y1  - 2016
U6  - http://dx.doi.org/10.1016/j.ijheatmasstransfer.2015.09.046
SN  - 0017-9310
IS  - 92
SP  - 884
EP  - 892
PB  - Elsevier
CY  - Amsterdam
ER  -