@article{Kaemper1996,
  author    = {K{\"a}mper, Klaus-Peter},
  title     = {Development of low-cost injection moulded micropumps. Entwicklung von kosteng{\"u}nstigen, mittels Spritzguß hergestellten Mikropumpen / D{\"o}pper, J. (u.a.)},
  series = {Actuator 96 : Conference Proceedings ; 5th International Conference on New Actuators ; 26- 28 June, Bremen, Germany / Ed.: Hubert Borgmann. Publ. by: AXON Technology Consult GmbH},
  journal   = {Actuator 96 : Conference Proceedings ; 5th International Conference on New Actuators ; 26- 28 June, Bremen, Germany / Ed.: Hubert Borgmann. Publ. by: AXON Technology Consult GmbH},
  address   = {Bremen},
  pages     = {37 -- 40},
  year      = {1996},
  language  = {en}
}
@article{KaemperKurzawaSchmittetal.1986,
  author    = {K{\"a}mper, Klaus-Peter and Kurzawa, R. and Schmitt, W. and G{\"u}ntherodt, G.},
  title     = {Spin-resolved photoemission study of in situ grown epitaxial Fe layers on W(110). Kurzawa, R.; K{\"a}mper, K.-P.; Schmitt, W.; G{\"u}ntherodt, G.},
  series = {Solid State Communications. 60 (1986), H. 10},
  journal   = {Solid State Communications. 60 (1986), H. 10},
  isbn      = {0038-1098},
  pages     = {777 -- 780},
  year      = {1986},
  language  = {en}
}
@article{GebhardtSchmidt2002,
  author    = {Gebhardt, Andreas and Schmidt, Frank-Michael},
  title     = {Practical experiences with making and finishing of coloured models using 3D printing},
  year      = {2002},
  language  = {en}
}
@article{Gebhardt2001,
  author    = {Gebhardt, Andreas},
  title     = {Rapid Prototyping and PIV},
  year      = {2001},
  language  = {en}
}
@article{Gebhardt2001,
  author    = {Gebhardt, Andreas},
  title     = {Laserwelding with fillerwire},
  series = {LIA handbook of laser material processing / Laser Institute of America},
  journal   = {LIA handbook of laser material processing / Laser Institute of America},
  address   = {Orlando, Florida},
  isbn      = {3-540-41770-2},
  year      = {2001},
  language  = {en}
}
@article{Gebhardt2006,
  author    = {Gebhardt, Andreas},
  title     = {Generative Manufacturing of Ceramic Parts "Vision Rapid Prototyping"},
  year      = {2006},
  abstract  = {Table of Contents Introduction 1. Generative Manufacturing Processes 2. Classification of Generative Manufacturing Processes 3. Application of Generative Processes on the Fabrication of Ceramic Parts 3.1 Extrusion 3.2 3D-Printing 3.3 Sintering - Laser Sintering 3.4 Layer-Laminate Processes 3.5 Stereolithography (sometimes written: Stereo Lithography) 4. Layer Milling 5. Conclusion - Vision},
  subject      = {Rapid prototyping},
  language  = {en}
}
@article{KaemperPicardBrilletal.2003,
  author    = {K{\"a}mper, Klaus-Peter and Picard, Antoni and Brill, Manfred and Cassel, Detlev and Jentsch, Andreas and Merten, Sabine and Rollwa, Markus},
  title     = {The Virtual Clean Room - a new tool in teaching MST process technologies},
  year      = {2003},
  abstract  = {The Virtual Clean Room - a new tool in teaching MST process technologies University education in high-technology fields like MST is not complete without intensive laboratory sessions. Students cannot fully grasp the complexity and the special problems related to the manufacturing of microsystems without a thorough hands-on experience in a MST clean room.},
  subject      = {Virtuelle Maschine},
  language  = {en}
}