@article{RichterBraunsteinStaeudleetal.2021,
  author    = {Richter, Charlotte and Braunstein, Bjoern and St{\"a}udle, Benjamin and Attias, Julia and Suess, Alexander and Weber, Tobias and Mileva, Katja N. and Rittweger, Joern and Green, David A. and Albracht, Kirsten},
  title     = {Gastrocnemius medialis contractile behavior is preserved during 30\% body weight supported gait training},
  series = {Frontiers in Sports and Active Living},
  volume    = {2021},
  journal   = {Frontiers in Sports and Active Living},
  number    = {2},
  publisher = {Frontiers},
  address   = {Lausanne},
  issn      = {2624-9367},
  doi       = {10.3389/fspor.2020.614559},
  pages     = {Artikel 614559},
  year      = {2021},
  abstract  = {Rehabilitative body weight supported gait training aims at restoring walking function as a key element in activities of daily living. Studies demonstrated reductions in muscle and joint forces, while kinematic gait patterns appear to be preserved with up to 30\% weight support. However, the influence of body weight support on muscle architecture, with respect to fascicle and series elastic element behavior is unknown, despite this having potential clinical implications for gait retraining. Eight males (31.9 ± 4.7 years) walked at 75\% of the speed at which they typically transition to running, with 0\% and 30\% body weight support on a lower-body positive pressure treadmill. Gastrocnemius medialis fascicle lengths and pennation angles were measured via ultrasonography. Additionally, joint kinematics were analyzed to determine gastrocnemius medialis muscle-tendon unit lengths, consisting of the muscle's contractile and series elastic elements. Series elastic element length was assessed using a muscle-tendon unit model. Depending on whether data were normally distributed, a paired t-test or Wilcoxon signed rank test was performed to determine if body weight supported walking had any effects on joint kinematics and fascicle-series elastic element behavior. Walking with 30\% body weight support had no statistically significant effect on joint kinematics and peak series elastic element length. Furthermore, at the time when peak series elastic element length was achieved, and on average across the entire stance phase, muscle-tendon unit length, fascicle length, pennation angle, and fascicle velocity were unchanged with respect to body weight support. In accordance with unchanged gait kinematics, preservation of fascicle-series elastic element behavior was observed during walking with 30\% body weight support, which suggests transferability of gait patterns to subsequent unsupported walking.},
  language  = {en}
}
@article{HerssensCowburnAlbrachtetal.2022,
  author    = {Herssens, Nolan and Cowburn, James and Albracht, Kirsten and Braunstein, Bjoern and Cazzola, Dario and Colyer, Steffi and Minetti, Alberto E. and Pavei, Gaspare and Rittweger, J{\"o}rn and Weber, Tobias and Green, David A.},
  title     = {Movement in low gravity environments (MoLo) programme - the MoLo-L.O.O.P. study protocol},
  series = {PLOS ONE / Public Library of Science},
  volume    = {17},
  journal   = {PLOS ONE / Public Library of Science},
  number    = {11},
  editor    = {Cattaneo, Luigi},
  publisher = {Plos},
  address   = {San Francisco},
  issn      = {1932-6203},
  doi       = {10.1371/journal.pone.0278051},
  pages     = {e0278051},
  year      = {2022},
  abstract  = {Exposure to prolonged periods in microgravity is associated with deconditioning of the musculoskeletal system due to chronic changes in mechanical stimulation. Given astronauts will operate on the Lunar surface for extended periods of time, it is critical to quantify both external (e.g., ground reaction forces) and internal (e.g., joint reaction forces) loads of relevant movements performed during Lunar missions. Such knowledge is key to predict musculoskeletal deconditioning and determine appropriate exercise countermeasures associated with extended exposure to hypogravity.},
  language  = {en}
}
@inproceedings{EnglhardWeberArent2021,
  author    = {Englhard, Markus and Weber, Tobias and Arent, Jan-Christoph},
  title     = {Efficiency enhancement for CFRP-Prepregautoclave manufacturing by means of simulation-assisted loading optimization},
  series = {Proceedings of SAMPE Europe Conference 2021},
  booktitle = {Proceedings of SAMPE Europe Conference 2021},
  pages     = {8 Seiten},
  year      = {2021},
  abstract  = {A new method for improved autoclave loading within the restrictive framework of helicopter manufacturing is proposed. It is derived from experimental and numerical studies of the curing process and aims at optimizing tooling positions in the autoclave for fast and homogeneous heat-up. The mold positioning is based on two sets of information. The thermal properties of the molds, which can be determined via semi-empirical thermal simulation. The second information is a previously determined distribution of heat transfer coefficients inside the autoclave. Finally, an experimental proof of concept is performed to show a cycle time reduction of up to 31\% using the proposed methodology.},
  language  = {en}
}
@inproceedings{OttenSchmidWeber2015,
  author    = {Otten, D. and Schmid, M. and Weber, Tobias},
  title     = {Advances In Sheet Metal-Forming: Reduction Of Tooling Cost By Methodical Optimization},
  series = {Proceedings of SAMPE Europe Conference, Amiens , France},
  booktitle = {Proceedings of SAMPE Europe Conference, Amiens , France},
  year      = {2015},
  language  = {en}
}
@inproceedings{Weber2015,
  author    = {Weber, Tobias},
  title     = {Manufacturing Process Simulation for Tooling Optimization: Reduction of Quality Issues During Autoclave Manufacturing of Composite Parts},
  series = {Proceedings of SAMPE Europe Conference 2015, Amiens, France},
  booktitle = {Proceedings of SAMPE Europe Conference 2015, Amiens, France},
  pages     = {1 -- 8},
  year      = {2015},
  language  = {en}
}
@inproceedings{WeberEnglhardHaileretal.2015,
  author    = {Weber, Tobias and Englhard, Markus and Hailer, Benjamin and Arent, Jan-Christoph},
  title     = {Manufacturing Process Simulation for the Prediction of Tool-Part-Interaction and Ply Wrinkling},
  series = {Proceedings of SAMPE Europe Conference, Amiens , France},
  booktitle = {Proceedings of SAMPE Europe Conference, Amiens , France},
  pages     = {1 -- 10},
  year      = {2015},
  language  = {en}
}
@inproceedings{WeberEnglhardHaileretal.2019,
  author    = {Weber, Tobias and Englhard, Markus and Hailer, Benjamin and Arent, Jan-Christoph},
  title     = {Manufacturing Process Simulation for the Prediction of Tool-Part-Interaction and Ply Wrinkling},
  series = {Proceedings of SAMPE Europe Conference 2019, Nantes, France},
  booktitle = {Proceedings of SAMPE Europe Conference 2019, Nantes, France},
  pages     = {1 -- 10},
  year      = {2019},
  language  = {en}
}
@inproceedings{HailerWeberArent2019,
  author    = {Hailer, Benjamin and Weber, Tobias and Arent, Jan-Christoph},
  title     = {Manufacturing Process Simulation for Autoclave-Produced Sandwich Structures},
  series = {Proceedings of SAMPE Europe Conference 2019, Nantes, France},
  booktitle = {Proceedings of SAMPE Europe Conference 2019, Nantes, France},
  pages     = {1 -- 8},
  year      = {2019},
  language  = {en}
}
@article{WeberArentMuenchetal.2016,
  author    = {Weber, Tobias and Arent, Jan-Christoph and M{\"u}nch, Lukas and Duhovic, Miro and Balvers, Johannes M.},
  title     = {A fast method for the generation of boundary conditions for thermal autoclave simulation},
  series = {Composites Part A},
  volume    = {88},
  journal   = {Composites Part A},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1359-835X},
  doi       = {10.1016/j.compositesa.2016.05.036},
  pages     = {216 -- 225},
  year      = {2016},
  abstract  = {Manufacturing process simulation enables the evaluation and improvement of autoclave mold concepts early in the design phase. To achieve a high part quality at low cycle times, the thermal behavior of the autoclave mold can be investigated by means of simulations. Most challenging for such a simulation is the generation of necessary boundary conditions. Heat-up and temperature distribution in an autoclave mold are governed by flow phenomena, tooling material and shape, position within the autoclave, and the chosen autoclave cycle. This paper identifies and summarizes the most important factors influencing mold heat-up and how they can be introduced into a thermal simulation. Thermal measurements are used to quantify the impact of the various parameters. Finally, the gained knowledge is applied to develop a semi-empirical approach for boundary condition estimation that enables a simple and fast thermal simulation of the autoclave curing process with reasonably high accuracy for tooling optimization.},
  language  = {en}
}
@inproceedings{WeberTellisDuhovic2016,
  author    = {Weber, Tobias and Tellis, Jane J. and Duhovic, Miro},
  title     = {Characterization of tool-part-interaction an interlaminar friction for manufacturing process simulation},
  series = {ECCM 17, 17th European Conference on Composite Materials, M{\"u}nchen, DE, Jun 26-30, 2016},
  booktitle = {ECCM 17, 17th European Conference on Composite Materials, M{\"u}nchen, DE, Jun 26-30, 2016},
  isbn      = {978-3-00-053387-7},
  pages     = {1 -- 7},
  year      = {2016},
  language  = {en}
}