@inproceedings{ZischankHeidlerKernetal.2002,
  author    = {Zischank, Wolfgang J. and Heidler, Fridolin and Kern, Alexander and Metwally, I. A. and Wiesinger, J. and Seevers, M.},
  title     = {Laboratory simulation of direct lightning strokes to a modelled building - measurement of magnetic fields and induced voltages},
  year      = {2002},
  abstract  = {In IEC 61312-2 equations for the assessment of the magnetic fields inside structures due to a direct lightning strike are given. These equations are based on computer simulations for shields consisting of a single-layer steel grid of a given mesh width. Real constructions, however, contain at least two layers of reinforcement steel grids. The objective of this study was to experimentally determine the additional shielding effectiveness of a second reinforcement layer compared to a single-layer grid. To this end, simulated structures were set up in the high current laboratory. The structures consisted of cubic cages of 2 m side length with one or with two reinforcement grids, respectively. The structures were exposed to direct lightning currents representing the variety of anticipated lightning current waveforms. The magnetic fields and their derivatives at several positions inside the structure as well as the voltage between "floor" and "roof" in the center were determined for different current injection points. From these data the improvement of the shielding caused by a second reinforcement layer is derived.},
  language  = {en}
}
@inproceedings{ZangHessRingbecketal.2002,
  author    = {Zang, Zhigang and Hess, Holger and Ringbeck, Thorsten and Schwarte, Rudolf},
  title     = {Phase-lock techniques using new correlation receivers for TOF-laser ranging},
  series = {Laser radar technology and applications VII : 3 - 4 April 2002, Orlando, USA. - (SPIE proceedings series ; 4723)},
  booktitle = {Laser radar technology and applications VII : 3 - 4 April 2002, Orlando, USA. - (SPIE proceedings series ; 4723)},
  editor    = {Kamerman, Gary W.},
  publisher = {SPIE, International Society for Optical Engineering},
  address   = {Bellingham, Wash.},
  isbn      = {0-8194-4473-1},
  issn      = {0038-7355},
  pages     = {112 -- 120},
  year      = {2002},
  language  = {en}
}
@inproceedings{WollertVedral2002,
  author    = {Wollert, J{\"o}rg and Vedral, Andreas},
  title     = {Einsatz von Opensource-Software f{\"u}r Evaluationsprototypen : Anwendungsempfehlungen und Einsatzbeispiele},
  series = {Vortr{\"a}ge und Begleittexte zum Entwicklerforum Wireless 2002 : Technologien und Grundlagen ; 16. Mai 2002},
  booktitle = {Vortr{\"a}ge und Begleittexte zum Entwicklerforum Wireless 2002 : Technologien und Grundlagen ; 16. Mai 2002},
  publisher = {Design \& Elektronik},
  address   = {Poing},
  organization    = {Entwicklerforum Wireless <2002, M{\"u}nchen>},
  pages     = {37 -- 46},
  year      = {2002},
  language  = {de}
}
@inproceedings{Wollert2002,
  author    = {Wollert, J{\"o}rg},
  title     = {Bluetooth in Embedded-Anwendungen in der Automatisierungstechnik},
  series = {Tagungsband / SPS IPC Drives 2002 : 13. Fachmesse und Kongress, 26. - 28. November 2002 N{\"u}rnberg; elektrische Automatisierung - Systeme und Komponenten. (Praxiswissen IEE - Automatisierung)},
  booktitle = {Tagungsband / SPS IPC Drives 2002 : 13. Fachmesse und Kongress, 26. - 28. November 2002 N{\"u}rnberg; elektrische Automatisierung - Systeme und Komponenten. (Praxiswissen IEE - Automatisierung)},
  publisher = {H{\"u}thig},
  address   = {Heidelberg},
  isbn      = {3-7785-2863-7},
  pages     = {28 -- 37},
  year      = {2002},
  language  = {de}
}
@inproceedings{WagnerNohButenwegetal.2002,
  author    = {Wagner, R. and Noh, S.-Y. and Butenweg, Christoph and Meskouris, Konstantin},
  title     = {Seismic excited granular material silos},
  series = {Structural dynamics - EURODYN 2002 : proceedings of the 4th [i.e. 5th] International Conference on Structural Dynamics, Munich, Germany, 2 - 5 September 2002 / ed. by H. Grundmann ...},
  booktitle = {Structural dynamics - EURODYN 2002 : proceedings of the 4th [i.e. 5th] International Conference on Structural Dynamics, Munich, Germany, 2 - 5 September 2002 / ed. by H. Grundmann ...},
  publisher = {Balkema},
  address   = {Lisse},
  organization    = {European Conference on Structural Dynamics, EURODYN <5, 2002, M{\"u}nchen>},
  isbn      = {90-5809-511-8},
  pages     = {253 -- 258},
  year      = {2002},
  language  = {en}
}
@inproceedings{VieiradaSilvaSchwarzerQueirozMedeiros2002,
  author    = {Vieira da Silva, Maria Eugenia and Schwarzer, Klemens and Queiroz Medeiros, Marcelo Ricardo},
  title     = {Experimental results of a solar cooker with heat storage},
  series = {RIO 02 - World Climate \& Energy Event, January 6-11, 2002},
  booktitle = {RIO 02 - World Climate \& Energy Event, January 6-11, 2002},
  year      = {2002},
  language  = {de}
}
@inproceedings{StaatHeitzer2002,
  author    = {Staat, Manfred and Heitzer, Michael},
  title     = {The restricted influence of kinematic hardening on shakedown loads},
  year      = {2002},
  abstract  = {Structural design analyses are conducted with the aim of verifying the exclusion of ratcheting. To this end it is important to make a clear distinction between the shakedown range and the ratcheting range. In cyclic plasticity more sophisticated hardening models have been suggested in order to model the strain evolution observed in ratcheting experiments. The hardening models used in shakedown analysis are comparatively simple. It is shown that shakedown analysis can make quite stable predictions of admissible load ranges despite the simplicity of the underlying hardening models. A linear and a nonlinear kinematic hardening model of two-surface plasticity are compared in material shakedown analysis. Both give identical or similar shakedown ranges. Structural shakedown analyses show that the loading may have a more pronounced effect than the hardening model.},
  subject      = {Biomedizinische Technik},
  language  = {en}
}
@inproceedings{Roeth2002,
  author    = {R{\"o}th, Thilo},
  title     = {Modularisierung in der Karosserie von morgen},
  year      = {2002},
  abstract  = {1) Module werden die Fahrzeugplattform und den -aufbau in Zukunft weiterhin und in zunehmendem Maße bestimmen. 2) Neue Module und Modulschnittstellen am Fahrzeug werden {\"u}berdacht und k{\"o}nnen in der Zukunft erwartet werden. 3) Die Wertsch{\"o}pfung und der Entwicklungsumfang wird sich vom OEM zum Modullieferanten verlagern. 4) Modulvergaben werden in der Zukunft noch st{\"a}rker auf Innovation und Kostenreduktion beruhen. 5) Modularisierung des Fahrzeuges heißt ein Aufbrechen der Fahrzeugkarosserie und wird daher von der Beherrschung struktureller Aufgaben sowie der L{\"o}sung der (sichtbaren) Modul{\"u}berg{\"a}nge bestimmt sein. 6) Neben den Systemintegratoren und den Komponentenspezialisten besetzen die Modullieferanten die erste Lieferantenriege. 7) Der Modullieferant wird neben h{\"o}chster Fertigungsexpertise ein hohes Maß an (Teil-)fahrzeug-Know-How und Produktentwickler-mentalit{\"a}t bereitstellen.},
  subject      = {Karosseriebau},
  language  = {de}
}
@inproceedings{Krause2002,
  author    = {Krause, Gregor},
  title     = {Energiemanagement in Geb{\"a}uden},
  series = {Energiemanagement in Geb{\"a}uden : 24. April 2002 : Tagung und Ausstellung},
  booktitle = {Energiemanagement in Geb{\"a}uden : 24. April 2002 : Tagung und Ausstellung},
  publisher = {Fachhochschule Aachen},
  address   = {Aachen},
  pages     = {1 -- 10},
  year      = {2002},
  language  = {de}
}
@inproceedings{KraftMeyerNagl2002,
  author    = {Kraft, Bodo and Meyer, Oliver and Nagl, Manfred},
  title     = {Graph technology support for conceptual design in civil engineering},
  isbn      = {3-18-318004-9},
  year      = {2002},
  abstract  = {In: Advances in intelligent computing in engineering : proceedings of the 9.International EG-ICE Workshop ; Darmstadt, (01 - 03 August) 2002 / Martina Schnellenbach-Held ... (eds.) . - D{\"u}sseldorf: VDI-Verl., 2002 .- Fortschritt-Berichte VDI, Reihe 4, Bauingenieurwesen ; 180 ; S. 1-35 The paper describes a novel way to support conceptual design in civil engineering. The designer uses semantical tools guaranteeing certain internal structures of the design result but also the fulfillment of various constraints. Two different approaches and corresponding tools are discussed: (a) Visually specified tools with automatic code generation to determine a design structure as well as fixing various constraints a design has to obey. These tools are also valuable for design knowledge specialist. (b) Extensions of existing CAD tools to provide semantical knowledge to be used by an architect. It is sketched how these different tools can be combined in the future. The main part of the paper discusses the concepts and realization of two prototypes following the two above approaches. The paper especially discusses that specific graphs and the specification of their structure are useful for both tool realization projects.},
  subject      = {CAD},
  language  = {en}
}