@inproceedings{GoettenFingerHavermannetal.2020,
  author    = {G{\"o}tten, Falk and Finger, Felix and Havermann, Marc and Braun, Carsten and Marino, Matthew and Bil, Cees},
  title     = {Full Configuration Drag Estimation of Small-to-Medium Range UAVs and its Impact on Initial Sizing Optimization},
  series = {Deutscher Luft- und Raumfahrtkongress - DLRK 2020},
  booktitle = {Deutscher Luft- und Raumfahrtkongress - DLRK 2020},
  year      = {2020},
  language  = {en}
}
@inproceedings{HippeFingerGoettenetal.2020,
  author    = {Hippe, Jonas and Finger, Felix and G{\"o}tten, Falk and Braun, Carsten},
  title     = {Propulsion System Qualification of a 25 kg VTOL-UAV: Hover Performance of Single and Coaxial Rotors and Wind-Tunnel Experiments on Cruise Propellers},
  series = {Deutscher Luft- und Raumfahrtkongress - DLRK 2020},
  booktitle = {Deutscher Luft- und Raumfahrtkongress - DLRK 2020},
  year      = {2020},
  language  = {en}
}
@article{FingerBraunBil2020,
  author    = {Finger, Felix and Braun, Carsten and Bil, Cees},
  title     = {Comparative assessment of parallel-hybrid-electric propulsion systems for four different aircraft},
  series = {Journal of Aircraft},
  volume    = {57},
  journal   = {Journal of Aircraft},
  number    = {5},
  publisher = {AIAA},
  address   = {Reston, Va.},
  issn      = {1533-3868},
  doi       = {10.2514/1.C035897},
  year      = {2020},
  abstract  = {Until electric energy storage systems are ready to allow fully electric aircraft, the combination of combustion engine and electric motor as a hybrid-electric propulsion system seems to be a promising intermediate solution. Consequently, the design space for future aircraft is expanded considerably, as serial hybrid-electric, parallel hybrid-electric, fully electric, and conventional propulsion systems must all be considered. While the best propulsion system depends on a multitude of requirements and considerations, trends can be observed for certain types of aircraft and certain types of missions. This Paper provides insight into some factors that drive a new design toward either conventional or hybrid propulsion systems. General aviation aircraft, regional transport aircraft vertical takeoff and landing air taxis, and unmanned aerial vehicles are chosen as case studies. Typical missions for each class are considered, and the aircraft are analyzed regarding their takeoff mass and primary energy consumption. For these case studies, a high-level approach is chosen, using an initial sizing methodology. Only parallel-hybrid-electric powertrains are taken into account. Aeropropulsive interaction effects are neglected. Results indicate that hybrid-electric propulsion systems should be considered if the propulsion system is sized by short-duration power constraints. However, if the propulsion system is sized by a continuous power requirement, hybrid-electric systems offer hardly any benefit.},
  language  = {en}
}
@article{GoettenHavermannBraunetal.2020,
  author    = {G{\"o}tten, Falk and Havermann, Marc and Braun, Carsten and Marino, Matthew and Bil, Cees},
  title     = {Airfoil drag at low-to-medium reynolds numbers: A novel estimation method},
  series = {AIAA Journal},
  volume    = {58},
  journal   = {AIAA Journal},
  number    = {7},
  publisher = {AIAA},
  address   = {Reston, Va.},
  issn      = {1533-385X},
  doi       = {10.2514/1.J058983},
  pages     = {2791 -- 2805},
  year      = {2020},
  abstract  = {This paper presents a novel method for airfoil drag estimation at Reynolds numbers between 4×10⁵ and 4×10⁶. The novel method is based on a systematic study of 40 airfoils applying over 600 numerical simulations and considering natural transition. The influence of the airfoil thickness-to-chord ratio, camber, and freestream Reynolds number on both friction and pressure drag is analyzed in detail. Natural transition significantly affects drag characteristics and leads to distinct drag minima for different Reynolds numbers and thickness-to-chord ratios. The results of the systematic study are used to develop empirical correlations that can accurately predict an airfoil drag at low-lift conditions. The new approach estimates a transition location based on airfoil thickness-to-chord ratio, camber, and Reynolds number. It uses the transition location in a mixed laminar-turbulent skin-friction calculation, and corrects the skin-friction coefficient for separation effects. Pressure drag is estimated separately based on correlations of thickness-to-chord ratio, camber, and Reynolds number. The novel method shows excellent accuracy when compared with wind-tunnel measurements of multiple airfoils. It is easily integrable into existing aircraft design environments and is highly beneficial in the conceptual design stage.},
  language  = {en}
}
@article{FingerGoettenBraunetal.2020,
  author    = {Finger, Felix and G{\"o}tten, Falk and Braun, Carsten and Bil, Cees},
  title     = {Mass, primary energy, and cost: the impact of optimization objectives on the initial sizing of hybrid-electric general aviation aircraft},
  series = {CEAS Aeronautical Journal},
  volume    = {2020},
  journal   = {CEAS Aeronautical Journal},
  number    = {11},
  publisher = {Springer},
  address   = {Heidelberg},
  issn      = {1869-5590},
  doi       = {10.1007/s13272-020-00449-8},
  pages     = {713 -- 730},
  year      = {2020},
  abstract  = {For short take-off and landing (STOL) aircraft, a parallel hybrid-electric propulsion system potentially offers superior performance compared to a conventional propulsion system, because the short-take-off power requirement is much higher than the cruise power requirement. This power-matching problem can be solved with a balanced hybrid propulsion system. However, there is a trade-off between wing loading, power loading, the level of hybridization, as well as range and take-off distance. An optimization method can vary design variables in such a way that a minimum of a particular objective is attained. In this paper, a comparison between the optimization results for minimum mass, minimum consumed primary energy, and minimum cost is conducted. A new initial sizing algorithm for general aviation aircraft with hybrid-electric propulsion systems is applied. This initial sizing methodology covers point performance, mission performance analysis, the weight estimation process, and cost estimation. The methodology is applied to the design of a STOL general aviation aircraft, intended for on-demand air mobility operations. The aircraft is sized to carry eight passengers over a distance of 500 km, while able to take off and land from short airstrips. Results indicate that parallel hybrid-electric propulsion systems must be considered for future STOL aircraft.},
  language  = {en}
}
@inproceedings{FingerKhalsaKreyeretal.2019,
  author    = {Finger, Felix and Khalsa, R. and Kreyer, J{\"o}rg and Mayntz, Joscha and Braun, Carsten and Dahmann, Peter and Esch, Thomas and Kemper, Hans and Schmitz, O. and Bragard, Michael},
  title     = {An approach to propulsion system modelling for the conceptual design of hybrid-electric general aviation aircraft},
  series = {Deutscher Luft- und Raumfahrtkongress 2019, 30.9.-2.10.2019, Darmstadt},
  booktitle = {Deutscher Luft- und Raumfahrtkongress 2019, 30.9.-2.10.2019, Darmstadt},
  pages     = {15 Seiten},
  year      = {2019},
  abstract  = {In this paper, an approach to propulsion system modelling for hybrid-electric general aviation aircraft is presented. Because the focus is on general aviation aircraft, only combinations of electric motors and reciprocating combustion engines are explored. Gas turbine hybrids will not be considered. The level of the component's models is appropriate for the conceptual design stage. They are simple and adaptable, so that a wide range of designs with morphologically different propulsive system architectures can be quickly compared. Modelling strategies for both mass and efficiency of each part of the propulsion system (engine, motor, battery and propeller) will be presented.},
  language  = {en}
}
@article{FingerBraunBil2020,
  author    = {Finger, Felix and Braun, Carsten and Bil, Cees},
  title     = {Impact of Battery Performance on the Initial Sizing of Hybrid-Electric General Aviation Aircraft},
  series = {Journal of Aerospace Engineering},
  volume    = {33},
  journal   = {Journal of Aerospace Engineering},
  number    = {3},
  publisher = {ASCE},
  address   = {Reston, Va.},
  issn      = {1943-5525},
  doi       = {10.1061/(ASCE)AS.1943-5525.0001113},
  year      = {2020},
  abstract  = {Studies suggest that hybrid-electric aircraft have the potential to generate fewer emissions and be inherently quieter when compared to conventional aircraft. By operating combustion engines together with an electric propulsion system, synergistic benefits can be obtained. However, the performance of hybrid-electric aircraft is still constrained by a battery's energy density and discharge rate. In this paper, the influence of battery performance on the gross mass for a four-seat general aviation aircraft with a hybrid-electric propulsion system is analyzed. For this design study, a high-level approach is chosen, using an innovative initial sizing methodology to determine the minimum required aircraft mass for a specific set of requirements and constraints. Only the peak-load shaving operational strategy is analyzed. Both parallel- and serial-hybrid propulsion configurations are considered for two different missions. The specific energy of the battery pack is varied from 200 to 1,000 W⋅h/kg, while the discharge time, and thus the normalized discharge rating (C-rating), is varied between 30 min (2C discharge rate) and 2 min (30C discharge rate). With the peak-load shaving operating strategy, it is desirable for hybrid-electric aircraft to use a light, low capacity battery system to boost performance. For this case, the battery's specific power rating proved to be of much higher importance than for full electric designs, which have high capacity batteries. Discharge ratings of 20C allow a significant take-off mass reduction aircraft. The design point moves to higher wing loadings and higher levels of hybridization if batteries with advanced technology are used.},
  language  = {en}
}
@inproceedings{FingerdeVriesVosetal.2020,
  author    = {Finger, Felix and de Vries, Reynard and Vos, Roelof and Braun, Carsten and Bil, Cees},
  title     = {A comparison of hybrid-electric aircraft sizing methods},
  series = {AIAA Scitech 2020 Forum},
  booktitle = {AIAA Scitech 2020 Forum},
  doi       = {10.2514/6.2020-1006},
  pages     = {31 Seiten},
  year      = {2020},
  language  = {en}
}
@inproceedings{FingerBraunBil2020,
  author    = {Finger, Felix and Braun, Carsten and Bil, Cees},
  title     = {Comparative assessment of parallel-hybrid-electric propulsion systems for four different aircraft},
  series = {AIAA SciTech Forum 2020, 06.01.2020 - 10.01.2020, Orlando},
  booktitle = {AIAA SciTech Forum 2020, 06.01.2020 - 10.01.2020, Orlando},
  doi       = {10.2514/6.2020-1502},
  pages     = {15 Seiten},
  year      = {2020},
  language  = {en}
}
@inproceedings{FingerGoettenBraunetal.2019,
  author    = {Finger, Felix and G{\"o}tten, Falk and Braun, Carsten and Bil, Cees},
  title     = {Cost Estimation Methods for Hybrid-Electric General Aviation Aircraft},
  series = {Asia Pacific International Symposium on Aerospace Technology. APISAT 2019},
  booktitle = {Asia Pacific International Symposium on Aerospace Technology. APISAT 2019},
  pages     = {1 -- 13},
  year      = {2019},
  language  = {en}
}