@incollection{KnottSofroniaGerressenetal.2014,
  author    = {Knott, Thomas C. and Sofronia, Raluca E. and Gerressen, Marcus and Law, Yuen and Davidescu, Arjana and Savii, George G. and Gatzweiler, Karl-Heinz and Staat, Manfred and Kuhlen, Torsten W.},
  title     = {Preliminary bone sawing model for a virtual reality-based training simulator of bilateral sagittal split osteotomy},
  series = {Biomedical simulation : 6th International Symposium, ISBMS 2014, Strasbourg, France, October 16-17, 2014 : proceedings (Lecture notes in computer science : vol. 8789)},
  booktitle = {Biomedical simulation : 6th International Symposium, ISBMS 2014, Strasbourg, France, October 16-17, 2014 : proceedings (Lecture notes in computer science : vol. 8789)},
  publisher = {Springer},
  address   = {Cham},
  isbn      = {978-3-319-12057-7 (Online)},
  doi       = {10.1007/978-3-319-12057-7_1},
  pages     = {1 -- 10},
  year      = {2014},
  abstract  = {Successful bone sawing requires a high level of skill and experience, which could be gained by the use of Virtual Reality-based simulators. A key aspect of these medical simulators is realistic force feedback. The aim of this paper is to model the bone sawing process in order to develop a valid training simulator for the bilateral sagittal split osteotomy, the most often applied corrective surgery in case of a malposition of the mandible. Bone samples from a human cadaveric mandible were tested using a designed experimental system. Image processing and statistical analysis were used for the selection of four models for the bone sawing process. The results revealed a polynomial dependency between the material removal rate and the applied force. Differences between the three segments of the osteotomy line and between the cortical and cancellous bone were highlighted.},
  language  = {en}
}
@article{KluczkaEcksteinAlexopoulosetal.2014,
  author    = {Kluczka, Sven and Eckstein, Julian and Alexopoulos, Spiros and Vaeßen, Christiane and Roeb, Martin},
  title     = {Process simulation for solar steam and dry reforming},
  series = {Energy procedia : Proceedings of the SolarPACES 2013 International Conference},
  volume    = {49},
  journal   = {Energy procedia : Proceedings of the SolarPACES 2013 International Conference},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1876-6102 (E-Journal)},
  doi       = {10.1016/j.egypro.2014.03.092},
  pages     = {850 -- 859},
  year      = {2014},
  abstract  = {In co-operation with the German Aerospace Center, the Solar-Institut J{\"u}lich has been analyzing the different technologies that are available for methanol production from CO2 using solar energy. The aim of the project is to extract CO2 from industrial exhaust gases or directly from the atmosphere to recycle it by use of solar energy. Part of the study was the modeling and simulating of a methane reformer for the production of synthesis gas, which can be operated by solar or hybrid heat sources. The reformer has been simplified in such a way that the model is accurate and enables fast calculations. The developed pseudo-homogeneous one- dimensional model can be regarded as a kind of counter-current heat exchanger and is able to incorporate a steam reforming reaction as well as a dry reforming reaction.},
  language  = {en}
}
@book{KlinkelButenwegLinetal.2014,
  author    = {Klinkel, Sven and Butenweg, Christoph and Lin, Gao and Holtschoppen, Britta},
  title     = {Seismic design of industrial facilities : Proceedings of the International Conference on Seismic Design of Industrial Facilities (SeDIF) / Sven Klinkel, Christoph Butenweg, Gao Lin, Britta Holtschoppen Editors},
  publisher = {Springer Vieweg},
  address   = {Wiesbaden},
  organization    = {International Conference on Seismic Design of Industrial Facilities <Aachen, 2013>},
  isbn      = {978-3-658-02809-1 (Print) ; 978-365-80281-0-7 (E-Book)},
  doi       = {10.1007/978-3-658-02810-7},
  pages     = {XIII, 450 S.},
  year      = {2014},
  language  = {en}
}
@inproceedings{KirschFelberMarcheretal.2014,
  author    = {Kirsch, Ansgar and Felber, W. and Marcher, Thomas and Fuchs, W.},
  title     = {Geotechnical challenges during design and construction of a ski resort in Azerbaijan},
  series = {Geotechnics of roads and railways : proceedings of the 15th Danube - European Conference on Geotechnical Engineering : 9-11 September 2014, Vienna, Austria},
  booktitle = {Geotechnics of roads and railways : proceedings of the 15th Danube - European Conference on Geotechnical Engineering : 9-11 September 2014, Vienna, Austria},
  publisher = {{\"O}IAV - {\"O}sterreichischer Ingenieur- und Architekten-Verein},
  address   = {Wien},
  organization    = {Danube - European Conference on Geotechnical Engineering <15, 2014, Wien>},
  isbn      = {978-3-902593-01-6},
  pages     = {757 -- 762},
  year      = {2014},
  language  = {en}
}
@incollection{KirchnerReisertSchoening2014,
  author    = {Kirchner, Patrick and Reisert, Steffen and Sch{\"o}ning, Michael Josef},
  title     = {Calorimetric gas sensors for hydrogen peroxide monitoring in aseptic food processes},
  series = {Gas sensing fundamentals. (Springer Series on Chemical Sensors and Biosensors ; 15)},
  booktitle = {Gas sensing fundamentals. (Springer Series on Chemical Sensors and Biosensors ; 15)},
  publisher = {Springer},
  address   = {Heidelberg},
  isbn      = {978-3-642-54518-4 (Print) ; 978-3-642-54519-1 (Online)},
  doi       = {10.1007/5346_2013_51},
  pages     = {279 -- 309},
  year      = {2014},
  abstract  = {For the sterilisation of aseptic food packages it is taken advantage of the microbicidal properties of hydrogen peroxide (H2O2). Especially, when applied in vapour phase, it has shown high potential of microbial inactivation. In addition, it offers a high environmental compatibility compared to other chemical sterilisation agents, as it decomposes into oxygen and water, respectively. Due to a lack in sensory detection possibilities, a continuous monitoring of the H2O2 concentration was recently not available. Instead, the sterilisation efficacy is validated using microbiological tests. However, progresses in the development of calorimetric gas sensors during the last 7 years have made it possible to monitor the H2O2 concentration during operation. This chapter deals with the fundamentals of calorimetric gas sensing with special focus on the detection of gaseous hydrogen peroxide. A sensor principle based on a calorimetric differential set-up is described. Special emphasis is given to the sensor design with respect to the operational requirements under field conditions. The state-of-the-art regarding a sensor set-up for the on-line monitoring and secondly, a miniaturised sensor for in-line monitoring are summarised. Furthermore, alternative detection methods and a novel multi-sensor system for the characterisation of aseptic sterilisation processes are described.},
  language  = {en}
}
@article{KhaydukovaZadorozhnayaKirsanovetal.2014,
  author    = {Khaydukova, M. M. and Zadorozhnaya, O. A. and Kirsanov, D. O. and Iken, Heiko and Rolka, David and Sch{\"o}ning, Michael Josef and Babain, V. A. and Vlasov, Yu. G. and Legin, A. V.},
  title     = {Multivariate processing of atomic-force microscopy images for detection of the response of plasticized polymeric membranes},
  series = {Russian journal of applied chemistry},
  volume    = {87},
  journal   = {Russian journal of applied chemistry},
  number    = {3},
  publisher = {Springer},
  address   = {Dordrecht},
  issn      = {1608-3296 (E-Journal); 1070-4272 (Print)},
  doi       = {10.1134/S1070427214030112},
  pages     = {307 -- 314},
  year      = {2014},
  abstract  = {The possibility of using the atomic-force microscopy as a method for detection of the analytical signal from plasticized polymeric sensor membranes was analyzed. The surfaces of cadmium-selective membranes based on two polymeric matrices were examined. The digital images were processed with multivariate image analysis techniques. A correlation was found between the surface profile of an ion-selective membrane and the concentration of the ion in solution.},
  language  = {en}
}
@book{KernWettingfeld2014,
  author    = {Kern, Alexander and Wettingfeld, J{\"u}rgen},
  title     = {Blitzschutzsysteme 1 : allgemeine Grunds{\"a}tze, Risikomanagement, Schutz von baulichen Anlagen und Personen ; Erl{\"a}uterungen zu den Normen DIN EN 62305-1 (VDE 0185-305-1):2011-10, DIN EN 62305-2 (VDE 0185-305-2):2013-02, DIN EN 62305-3 (VDE 0185-305-3):2011-10. (VDE-Schriftenreihe Normen verst{\"a}ndlich ; 44)},
  publisher = {VDE-Verl.},
  address   = {Berlin [u.a.]},
  isbn      = {978-3-8007-3511-2},
  pages     = {308 S.},
  year      = {2014},
  language  = {de}
}
@inproceedings{KernBraun2014,
  author    = {Kern, Alexander and Braun, Christian},
  title     = {Risk management according to IEC 62305-2 edition 2: 2010-12 assessment of structures with a risk of explosion},
  series = {2014 International Conference on Lightning Protection (ICLP), Shanghai, China},
  booktitle = {2014 International Conference on Lightning Protection (ICLP), Shanghai, China},
  organization    = {International Conference on Lightning Protection <2014, Shanghai>},
  pages     = {1237 -- 1242},
  year      = {2014},
  abstract  = {Risk management for structures with a risk of explosion should be considered very carefully when performing a risk analysis according to IEC 62305-2. In contrast to the 2006 edition of the standard, the 2010 edition describes the topic "Structures with a risk of explosion" in more detail. Moreover, in Germany separate procedures and parameters are defined for the risk analysis of structures with a risk of explosion (Supplement 3 of the German DIN EN 62305-2 standard). This paper describes the contents and the relevant calculations of this Supplement 3, together with a numerical example.},
  language  = {en}
}
@inproceedings{KallweitFerreinScholletal.2014,
  author    = {Kallweit, Stephan and Ferrein, Alexander and Scholl, Ingrid and Reichert, Walter},
  title     = {Mobile Autonome Systeme in der Lehre, am Beispiel der ROS Summer School},
  series = {Tagungsband AALE 2014 : das Forum f{\"u}r Fachleute der Automatisierungstechnik aus Hochschulen und Wirtschaft ; 11. Fachkonferenz, Regensburg ; [11. Konferenz f{\"u}r Angewandte Automatisierungstechnik in Lehre und Entwicklung / Ostbayerische Technische Hochschule Regensburg; VFAALE, Verein der Freunde und F{\"o}rderer der Angewandten Automatisierungstechnik]},
  booktitle = {Tagungsband AALE 2014 : das Forum f{\"u}r Fachleute der Automatisierungstechnik aus Hochschulen und Wirtschaft ; 11. Fachkonferenz, Regensburg ; [11. Konferenz f{\"u}r Angewandte Automatisierungstechnik in Lehre und Entwicklung / Ostbayerische Technische Hochschule Regensburg; VFAALE, Verein der Freunde und F{\"o}rderer der Angewandten Automatisierungstechnik]},
  publisher = {Dt. Industrieverl.},
  address   = {M{\"u}nchen},
  isbn      = {978-3-8356-7142-3},
  pages     = {157 -- 163},
  year      = {2014},
  language  = {de}
}
@article{JoerissenHeger2014,
  author    = {J{\"o}rissen, J{\"o}rg and Heger, Michael},
  title     = {Zur Wirkung hochschuldidaktisch fundierter und in den Fachbereichen verankerter Lehrveranstaltungsevaluation},
  series = {Qualit{\"a}t in der Wissenschaft (QiW)},
  volume    = {8},
  journal   = {Qualit{\"a}t in der Wissenschaft (QiW)},
  number    = {2+3},
  publisher = {Universit{\"a}tsverlag Webler},
  address   = {Bielefeld},
  issn      = {1860-3041},
  pages     = {70 -- 80},
  year      = {2014},
  language  = {de}
}