@article{GoettenFingerHavermannetal.2021,
  author    = {G{\"o}tten, Falk and Finger, Felix and Havermann, Marc and Braun, Carsten and Marino, M. and Bil, C.},
  title     = {Full configuration drag estimation of short-to-medium range fixed-wing UAVs and its impact on initial sizing optimization},
  series = {CEAS Aeronautical Journal},
  volume    = {12},
  journal   = {CEAS Aeronautical Journal},
  publisher = {Springer},
  address   = {Berlin},
  issn      = {1869-5590 (Online)},
  doi       = {10.1007/s13272-021-00522-w},
  pages     = {589 -- 603},
  year      = {2021},
  abstract  = {The paper presents the derivation of a new equivalent skin friction coefficient for estimating the parasitic drag of short-to-medium range fixed-wing unmanned aircraft. The new coefficient is derived from an aerodynamic analysis of ten different unmanned aircraft used for surveillance, reconnaissance, and search and rescue missions. The aircraft is simulated using a validated unsteady Reynolds-averaged Navier Stokes approach. The UAV's parasitic drag is significantly influenced by the presence of miscellaneous components like fixed landing gears or electro-optical sensor turrets. These components are responsible for almost half of an unmanned aircraft's total parasitic drag. The new equivalent skin friction coefficient accounts for these effects and is significantly higher compared to other aircraft categories. It is used to initially size an unmanned aircraft for a typical reconnaissance mission. The improved parasitic drag estimation yields a much heavier unmanned aircraft when compared to the sizing results using available drag data of manned aircraft.},
  language  = {en}
}
@article{GoettenHavermannBraunetal.2021,
  author    = {G{\"o}tten, Falk and Havermann, Marc and Braun, Carsten and Marino, Matthew and Bil, Cees},
  title     = {Aerodynamic Investigations of UAV Sensor Turrets - A Combined Wind-tunnel and CFD Approach},
  series = {SciTech 2021, AIAA SciTech Forum, online, WW, Jan 11-15, 2021},
  journal   = {SciTech 2021, AIAA SciTech Forum, online, WW, Jan 11-15, 2021},
  publisher = {AIAA},
  address   = {Reston, Va.},
  doi       = {10.2514/6.2021-1535},
  pages     = {1 -- 12},
  year      = {2021},
  language  = {en}
}
@article{GoettenHavermannBraunetal.2020,
  author    = {G{\"o}tten, Falk and Havermann, Marc and Braun, Carsten and Marino, Matthew and Bil, Cees},
  title     = {Airfoil drag at low-to-medium reynolds numbers: A novel estimation method},
  series = {AIAA Journal},
  volume    = {58},
  journal   = {AIAA Journal},
  number    = {7},
  publisher = {AIAA},
  address   = {Reston, Va.},
  issn      = {1533-385X},
  doi       = {10.2514/1.J058983},
  pages     = {2791 -- 2805},
  year      = {2020},
  abstract  = {This paper presents a novel method for airfoil drag estimation at Reynolds numbers between 4×10⁵ and 4×10⁶. The novel method is based on a systematic study of 40 airfoils applying over 600 numerical simulations and considering natural transition. The influence of the airfoil thickness-to-chord ratio, camber, and freestream Reynolds number on both friction and pressure drag is analyzed in detail. Natural transition significantly affects drag characteristics and leads to distinct drag minima for different Reynolds numbers and thickness-to-chord ratios. The results of the systematic study are used to develop empirical correlations that can accurately predict an airfoil drag at low-lift conditions. The new approach estimates a transition location based on airfoil thickness-to-chord ratio, camber, and Reynolds number. It uses the transition location in a mixed laminar-turbulent skin-friction calculation, and corrects the skin-friction coefficient for separation effects. Pressure drag is estimated separately based on correlations of thickness-to-chord ratio, camber, and Reynolds number. The novel method shows excellent accuracy when compared with wind-tunnel measurements of multiple airfoils. It is easily integrable into existing aircraft design environments and is highly beneficial in the conceptual design stage.},
  language  = {en}
}
@article{GoettenHavermannBraunetal.2020,
  author    = {G{\"o}tten, Falk and Havermann, Marc and Braun, Carsten and Marino, Matthew and Bil, Cees},
  title     = {Wind-tunnel and CFD investigations of UAV landing gears and turrets - Improvements in empirical drag estimation},
  series = {Aerospace Science and Technology},
  volume    = {107},
  journal   = {Aerospace Science and Technology},
  number    = {Art. 106306},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1270-9638},
  doi       = {10.1016/j.ast.2020.106306},
  year      = {2020},
  abstract  = {This paper analyzes the drag characteristics of several landing gear and turret configurations that are representative of unmanned aircraft tricycle landing gears and sensor turrets. A variety of these components were constructed via 3D-printing and analyzed in a wind-tunnel measurement campaign. Both turrets and landing gears were attached to a modular fuselage that supported both isolated components and multiple components at a time. Selected cases were numerically investigated with a Reynolds-averaged Navier-Stokes approach that showed good accuracy when compared to wind-tunnel data. The drag of main gear struts could be significantly reduced via streamlining their cross-sectional shape and keeping load carrying capabilities similar. The attachment of wheels introduced interference effects that increased strut drag moderately but significantly increased wheel drag compared to isolated cases. Very similar behavior was identified for front landing gears. The drag of an electro-optical and infrared sensor turret was found to be much higher than compared to available data of a clean hemisphere-cylinder combination. This turret drag was merely influenced by geometrical features like sensor surfaces and the rotational mechanism. The new data of this study is used to develop simple drag estimation recommendations for main and front landing gear struts and wheels as well as sensor turrets. These recommendations take geometrical considerations and interference effects into account.},
  language  = {en}
}
@article{GoettenHavermannBraunetal.2020,
  author    = {G{\"o}tten, Falk and Havermann, Marc and Braun, Carsten and Marino, Matthew and Bil, Cees},
  title     = {Improved Form Factor for Drag Estimation of Fuselages with Various Cross Sections},
  series = {Journal of Aircraft},
  journal   = {Journal of Aircraft},
  publisher = {AIAA},
  address   = {Reston, Va.},
  issn      = {1533-3868},
  doi       = {10.2514/1.C036032},
  pages     = {1 -- 13},
  year      = {2020},
  abstract  = {The paper presents an aerodynamic investigation of 70 different streamlined bodies with fineness ratios ranging from 2 to 10. The bodies are chosen to idealize both unmanned and small manned aircraft fuselages and feature cross-sectional shapes that vary from circular to quadratic. The study focuses on friction and pressure drag in dependency of the individual body's fineness ratio and cross section. The drag forces are normalized with the respective body's wetted area to comply with an empirical drag estimation procedure. Although the friction drag coefficient then stays rather constant for all bodies, their pressure drag coefficients decrease with an increase in fineness ratio. Referring the pressure drag coefficient to the bodies' cross-sectional areas shows a distinct pressure drag minimum at a fineness ratio of about three. The pressure drag of bodies with a quadratic cross section is generally higher than for bodies of revolution. The results are used to derive an improved form factor that can be employed in a classic empirical drag estimation method. The improved formulation takes both the fineness ratio and cross-sectional shape into account. It shows superior accuracy in estimating streamlined body drag when compared with experimental data and other form factor formulations of the literature.},
  language  = {en}
}
@article{GoettenHavermannBraunetal.2019,
  author    = {G{\"o}tten, Falk and Havermann, Marc and Braun, Carsten and Gomez, Francisco and Bil, Cees},
  title     = {RANS Simulation Validation of a Small Sensor Turret for UAVs},
  series = {Journal of Aerospace Engineering},
  volume    = {32},
  journal   = {Journal of Aerospace Engineering},
  number    = {5},
  publisher = {ASCE},
  address   = {New York},
  issn      = {1943-5525},
  doi       = {10.1061/(ASCE)AS.1943-5525.0001055},
  pages     = {Article number 04019060},
  year      = {2019},
  abstract  = {Recent Unmanned Aerial Vehicle (UAV) design procedures rely on full aircraft steady-state Reynolds-Averaged-Navier-Stokes (RANS) analyses in early design stages. Small sensor turrets are included in such simulations, even though their aerodynamic properties show highly unsteady behavior. Very little is known about the effects of this approach on the simulation outcomes of small turrets. Therefore, the flow around a model turret at a Reynolds number of 47,400 is simulated with a steady-state RANS approach and compared to experimental data. Lift, drag, and surface pressure show good agreement with the experiment. The RANS model predicts the separation location too far downstream and shows a larger recirculation region aft of the body. Both characteristic arch and horseshoe vortex structures are visualized and qualitatively match the ones found by the experiment. The Reynolds number dependence of the drag coefficient follows the trend of a sphere within a distinct range. The outcomes indicate that a steady-state RANS model of a small sensor turret is able to give results that are useful for UAV engineering purposes but might not be suited for detailed insight into flow properties.},
  language  = {en}
}
@article{GoettenFingerHavermannetal.2018,
  author    = {G{\"o}tten, Falk and Finger, Felix and Havermann, Marc and Braun, Carsten and Gomez, Francisco and Bill, C.},
  title     = {On the flight performance impact of landing gear drag reduction methods for unmanned air vehicles},
  series = {Deutscher Luft- und Raumfahrtkongress 2018},
  journal   = {Deutscher Luft- und Raumfahrtkongress 2018},
  publisher = {DGLR},
  address   = {Bonn},
  doi       = {10.25967/480058},
  pages     = {11 S.},
  year      = {2018},
  abstract  = {The flight performance impact of three different landing gear configurations on a small, fixed-wing UAV is analyzed with a combination of RANS CFD calculations and an incremental flight performance algorithm. A standard fixed landing gear configuration is taken as a baseline, while the influence of retracting the landing gear or applying streamlined fairings is investigated. A retraction leads to a significant parasite drag reduction, while also fairings promise large savings. The increase in lift-to-drag ratio is reduced at high lift coefficients due to the influence of induced drag. All configurations are tested on three different design missions with an incremental flight performance algorithm. A trade-off study is performed using the retracted or faired landing gear's weight increase as a variable. The analysis reveals only small mission performance gains as the aerodynamic improvements are negated by weight penalties. A new workflow for decision-making is presented that allows to estimate if a change in landing gear configuration is beneficial for a small UAV.},
  language  = {en}
}
@article{LettiniHavermannGuidettietal.2010,
  author    = {Lettini, Antonio and Havermann, Marc and Guidetti, Marco and Fornaciari, Andrea},
  title     = {Improved functionalities and energy saving potential on mobile machines combining electronics with flow sharing valve and variable displacement pump},
  series = {IFK 7, 7th International Fluid Power Conference, Efficiency through Fluid Power, 7. Internationales Fluidtechnisches Kolloquium, Workshop Proceedings, Vol. 3, Aachen, DE, 22.-24. Mar, 2010},
  journal   = {IFK 7, 7th International Fluid Power Conference, Efficiency through Fluid Power, 7. Internationales Fluidtechnisches Kolloquium, Workshop Proceedings, Vol. 3, Aachen, DE, 22.-24. Mar, 2010},
  publisher = {-},
  isbn      = {978-3-940565-92-1},
  pages     = {103 -- 114},
  year      = {2010},
  language  = {en}
}
@article{FornaciariGuidettiHavermannetal.2010,
  author    = {Fornaciari, Andrea and Guidetti, Marco and Havermann, Marc and Lettini, Antonio},
  title     = {Maccine mobili pi{\`u} efficienti},
  series = {Fluidotecnica},
  journal   = {Fluidotecnica},
  number    = {345},
  publisher = {Quine Business Publisher},
  address   = {Milano},
  pages     = {11 -- 14},
  year      = {2010},
  abstract  = {Secondo le attuali normative tutte le macchine mobili, entro il 2012, dovranno essere soggette a un incremento di efficienza energetica. Un'evoluzione del sistema idraulico potr{\`a} contribuire in maniera significativa al miglioramento richiesto. Elettronica e idraulica sempre pi{\`u} protagoniste.},
  language  = {it}
}
@article{PichlerGeorgeSeileretal.2009,
  author    = {Pichler, A. and George, A. and Seiler, F. and Srulijes, J. and Havermann, Marc},
  title     = {Doppler Picture Velocimetry (DPV) applied to hypersonics},
  series = {Shock Waves [Elektronische Ressource] : 26th International Symposium on Shock Waves, Volume 1 / edited by Klaus Hannemann, Friedrich Seiler},
  journal   = {Shock Waves [Elektronische Ressource] : 26th International Symposium on Shock Waves, Volume 1 / edited by Klaus Hannemann, Friedrich Seiler},
  publisher = {Springer},
  address   = {Berlin},
  isbn      = {978-3-540-85168-4},
  pages     = {503 -- 508},
  year      = {2009},
  language  = {en}
}