@article{AhmedReisgenSchleseretal.2010,
  author    = {Ahmed, Essam and Reisgen, Uwe and Schleser, Markus and Mokrov, Oleg},
  title     = {On formability of tailor laser welded blanks of DP/TRIP steel sheets},
  series = {Science and technology of welding and joining},
  volume    = {15},
  journal   = {Science and technology of welding and joining},
  number    = {5},
  publisher = {Maney},
  address   = {Leeds},
  issn      = {1743-2936},
  doi       = {10.1179/136217110X12731414739754},
  pages     = {337 -- 342},
  year      = {2010},
  abstract  = {This paper aims to evaluate the formability of tailor welded blanks of dual phase (DP600)/transformation induced plasticity (TRIP700) steel sheets. In this work, bead on plate butt joints of 2·5 mm DP600 and 1·2 mm TRIP700 steel sheets were performed using CO2 laser beam welding. Microhardness measurements and transverse tensile testing were carried out to characterise the welds. The formability of base metals and welds were investigated by standard Erichsen test. In a perpendicular tensile test to the weld line, all specimens were fractured at the TRIP base metal, and the strengths were somewhat higher than those of base metal. There was a significant reduction in formability caused by welding of the DP600/TRIP700 steel sheets, and the formability increased with increasing welding speed.},
  language  = {en}
}
@inproceedings{SchoeneReisgenSchleseretal.2010,
  author    = {Schoene, Jens and Reisgen, Uwe and Schleser, Markus and Jerabek, Jakub and Chudoba, Rostislav},
  title     = {Theoretical and experimental investigations on textile-reinforced concrete spalling behavior},
  series = {8th International PhD Symposium in Civil Engineering : Lyngby, June 20-23, 2010 : proceedings},
  booktitle = {8th International PhD Symposium in Civil Engineering : Lyngby, June 20-23, 2010 : proceedings},
  editor    = {Fisher, Gregor},
  publisher = {Technical University of Denmark, Dept. of Civil Engineering},
  address   = {Lyngby},
  organization    = {PhD Symposium in Civil Engineering <8, 2010, Lyngby> ; International Federation for Structural Concrete},
  isbn      = {9788778773012},
  pages     = {383 -- 388},
  year      = {2010},
  language  = {en}
}
@article{HaselgruberMautnerThiele2010,
  author    = {Haselgruber, Nikolaus and Mautner, Karin and Thiele, Jan},
  title     = {Usage Space Analysis for Reliability Testing},
  series = {Quality and Reliability Engineering International},
  volume    = {26},
  journal   = {Quality and Reliability Engineering International},
  number    = {8},
  publisher = {Wiley},
  address   = {New York},
  issn      = {1099-1638},
  doi       = {10.1002/qre.1155},
  pages     = {877 -- 885},
  year      = {2010},
  abstract  = {During the development process of a complex technical product, one widely used and important technique is accelerated testing where the applied stress on a component is chosen to exceed the reference stress, i.e. the stress encountered in field operation, in order to reduce the time to failure. For that, the reference stress has to be known. Since a complex technical product may fail regarding numerous failure modes, stress in general is highly dimensional rather than scalar. In addition, customers use their products individually, i.e. field operation should be described by a distribution rather than by one scalar stress value. In this paper, a way to span the customer usage space is shown. It allows the identification of worst case reference stress profiles in significantly reduced dimensions with minimal loss of information. The application example shows that even for a complex product like a combustion engine, stress information can be compressed significantly. With low measurement effort it turned out that only three reference stress cycles were sufficient to cover a broad range of customer stress variety.},
  language  = {en}
}
@article{GebhardtSchmidtHoetteretal.2010,
  author    = {Gebhardt, Andreas and Schmidt, Frank-Michael and H{\"o}tter, Jan-Steffen and Sokalla, Wolfgang and Sokalla, Patrick},
  title     = {Additive Manufacturing by selective laser melting the realizer desktop machine and its application for the dental industry},
  series = {Physics Procedia},
  volume    = {5},
  journal   = {Physics Procedia},
  number    = {2},
  isbn      = {1875-3892},
  pages     = {543 -- 549},
  year      = {2010},
  language  = {en}
}