@article{RauAlexopoulosBreitbachetal.2014, author = {Rau, Christoph and Alexopoulos, Spiros and Breitbach, Gerd and Hoffschmidt, Bernhard and Latzke, Markus and Sattler, Johannes Christoph}, title = {Transient simulation of a solar-hybrid tower power plant with open volumetric receiver at the location Barstow}, series = {Energy procedia : proceedings of the SolarPACES 2013 International Conference}, volume = {49}, journal = {Energy procedia : proceedings of the SolarPACES 2013 International Conference}, publisher = {Elsevier}, address = {Amsterdam}, issn = {1876-6102}, doi = {10.1016/j.egypro.2014.03.157}, pages = {1481 -- 1490}, year = {2014}, abstract = {In this work the transient simulations of four hybrid solar tower power plant concepts with open-volumetric receiver technology for a location in Barstow-Daggett, USA, are presented. The open-volumetric receiver uses ambient air as heat transfer fluid and the hybridization is realized with a gas turbine. The Rankine cycle is heated by solar-heated air and/or by the gas turbine's flue gases. The plant can be operated in solar-only, hybrid parallel or combined cycle-only mode as well as in any intermediate load levels where the solar portion can vary between 0 to 100\%. The simulated plant is based on the configuration of a solar-hybrid power tower project, which is in planning for a site in Northern Algeria. The meteorological data for Barstow-Daggett was taken from the software meteonorm. The solar power tower simulation tool has been developed in the simulation environment MATLAB/Simulink and is validated.}, language = {en} } @article{KronhardtAlexopoulosReisseletal.2014, author = {Kronhardt, Valentina and Alexopoulos, Spiros and Reißel, Martin and Sattler, Johannes Christoph and Hoffschmidt, Bernhard and H{\"a}nel, Matthias and Doerbeck, Till}, title = {High-temperature thermal storage system for solar tower power plants with open-volumetric air receiver simulation and energy balancing of a discretized model}, series = {Energy procedia}, volume = {49}, journal = {Energy procedia}, publisher = {Elsevier}, address = {Amsterdam}, issn = {1876-6102 (E-Journal) ; 1876-6102 (Print)}, doi = {10.1016/j.egypro.2014.03.094}, pages = {870 -- 877}, year = {2014}, abstract = {This paper describes the modeling of a high-temperature storage system for an existing solar tower power plant with open volumetric receiver technology, which uses air as heat transfer medium (HTF). The storage system model has been developed in the simulation environment Matlab/Simulink®. The storage type under investigation is a packed bed thermal energy storage system which has the characteristics of a regenerator. Thermal energy can be stored and discharged as required via the HTF air. The air mass flow distribution is controlled by valves, and the mass flow by two blowers. The thermal storage operation strategy has a direct and significant impact on the energetic and economic efficiency of the solar tower power plants.}, language = {en} } @article{JiminezGermanBehbahaniMiettinenetal.2013, author = {Jiminez German, Salvador and Behbahani, Mehdi and Miettinen, Susanna and Grijpma, Dirk W. and Haimi, Suvi P.}, title = {Proliferation and differentiation of adipose stem cells towards smooth muscle cells on poly(trimethylene carbonate) membranes}, series = {Macromolecular symposia}, volume = {Vol. 334}, journal = {Macromolecular symposia}, number = {Iss. 1}, publisher = {Wiley}, address = {Weinheim}, issn = {0258-0322}, pages = {133 -- 142}, year = {2013}, language = {en} } @article{BuniatyanHuckPoghossianetal.2013, author = {Buniatyan, V. and Huck, Christina and Poghossian, Arshak and Aroutiounian, V. M. and Sch{\"o}ning, Michael Josef}, title = {BaxSr1-x TiO3/pc-Si heterojunction}, series = {Armenian journal of physics}, volume = {6}, journal = {Armenian journal of physics}, number = {4}, publisher = {National Academy of Sciences of Armenia}, address = {Yerevan}, issn = {1829-1171}, pages = {177 -- 187}, year = {2013}, language = {en} } @article{BuniatyanHuckPoghossianetal.2013, author = {Buniatyan, V. and Huck, Christina and Poghossian, Arshak and Aroutiounian, V. M. and Sch{\"o}ning, Michael Josef}, title = {BaxSr1-x TiO3/pc-Si heterojunction capacitance}, series = {Armenian journal of physics}, volume = {6}, journal = {Armenian journal of physics}, number = {4}, publisher = {National Academy of Sciences of Armenia}, address = {Yerevan}, issn = {1829-1171}, pages = {188 -- 197}, year = {2013}, language = {en} } @article{SabitovaEbertLenzetal.2013, author = {Sabitova, A. and Ebert, Ph. and Lenz, A. and Schaafhausen, S. and Ivanova, L. and D{\"a}hne, M. and Hoffmann, A. and Dunin-Borkowski, R. E. and F{\"o}rster, Arnold and Grandidier, B. and Eisele, H.}, title = {Intrinsic bandgap of cleaved ZnO(112¯0) surfaces}, series = {Applied physics letters}, volume = {Vol. 102}, journal = {Applied physics letters}, issn = {1077-3118 (E-Journal); 0003-6951 (Print)}, pages = {021608}, year = {2013}, language = {en} } @article{HoetterFateriGebhardt2012, author = {H{\"o}tter, Jan-Steffen and Fateri, Miranda and Gebhardt, Andreas}, title = {Selective laser melting of metals: desktop machines open up new chances even for small companies}, series = {Advanced materials research}, volume = {622-623}, journal = {Advanced materials research}, publisher = {Trans Tech Publ.}, address = {Baech}, issn = {1662-8985 (E-Journal); 1022-6680 (Print)}, doi = {10.4028/www.scientific.net/AMR.622-623.461}, pages = {461 -- 465}, year = {2012}, abstract = {Additive manufacturing (AM) of metal parts by using Selective Laser Melting (SLM) has become a powerful tool mostly in the area of automotive, aerospace engineering and others. Especially in the field of dentistry, jewelry and related branches that require individualized or even one-of-a-kind products, the direct digital manufacturing process opens up new ways of design and manufacturing. In these fields, mostly small and medium sized businesses (SME) are operating which do not have sufficient human and economic resources to invest in this technology. But to stay competitive, the application of AM can be regarded as a necessity. In this situation a new desktop machine (Realizer SLM 50) was introduced that cost about 1/3 of a shop floor SLM machine and promises small quality parts. To find out whether the machine really is an alternative for SMEs the University of Applied Science, Aachen, Germany, designed, build and optimized typical parts from the dentistry and the jewelry branches using CoCr and silver material, the latter being new with this application. The paper describes the SLM procedure and how to find and optimize the most important parameters. The test is accompanied by digital simulation in order to verify the build parameters and to plan future builds. The procedure is shown as well as the resulting parts made from CoCr and silver material.}, language = {en} } @article{MiciliValterOflazetal.2013, author = {Micili, Serap C. and Valter, Markus and Oflaz, Hakan and Ozogul, Candan and Linder, Peter and F{\"o}ckler, Nicole and Artmann, Gerhard and Digel, Ilya and Temiz Artmann, Ayseg{\"u}l}, title = {Optical coherence tomography : a potential tool to predict premature rupture of fetal membranes}, series = {Proceedings of the Institution of Mechanical Engineers. Part H : Journal of engineering in medicine}, volume = {Vol. 227}, journal = {Proceedings of the Institution of Mechanical Engineers. Part H : Journal of engineering in medicine}, number = {No. 4}, publisher = {Sage}, address = {London}, issn = {0046-2039 (Print) ; 2041-3033 (E-Journal)}, pages = {393 -- 401}, year = {2013}, language = {en} } @article{KruegerGroetzingerBerndt1987, author = {Kr{\"u}ger, G{\"o}tz and Gr{\"o}tzinger, Joachim and Berndt, Heinz}, title = {Enantiomeric resolution of amino acid derivatives on chiral stationary phases by high-performance liquid chromatography}, series = {Journal of Chromatography A}, volume = {1987}, journal = {Journal of Chromatography A}, number = {397}, issn = {0021-9673}, doi = {10.1016/S0021-9673(01)85005-6}, pages = {223 -- 232}, year = {1987}, language = {en} } @article{Bung2011, author = {Bung, Daniel Bernhard}, title = {Developing flow in skimming flow regime on embankment stepped spillways}, series = {Journal of hydraulic research}, volume = {Vol. 49}, journal = {Journal of hydraulic research}, number = {Iss. 5}, publisher = {Taylor \& Francis}, address = {London}, issn = {1814-2079 (E-Journal); 0022-1686 (Print)}, pages = {639 -- 648}, year = {2011}, language = {en} } @article{OertelBung2012, author = {Oertel, Mario and Bung, Daniel Bernhard}, title = {Initial stage of two-dimensional dam-break waves: laboratory versus VOF}, series = {Journal of hydraulic research}, volume = {50}, journal = {Journal of hydraulic research}, number = {1}, publisher = {Taylor \& Francis}, address = {London}, issn = {1814-2079 (E-Journal); 0022-1686 (Print)}, doi = {10.1080/00221686.2011.639981}, pages = {89 -- 97}, year = {2012}, abstract = {Since several decades, dam-break waves have been of main research interest. Mathematical approaches have been developed by analytical, physical and numerical models within the past 120 years. During the past 10 years, the number of research investigations has increased due to improved measurement techniques as well as significantly increased computer memories and performances. In this context, the present research deals with the initial stage of two-dimensional dam-break waves by comparing physical and numerical model results as well as analytical approaches. High-speed images and resulting particle image velocimetry calculations are thereby compared with the numerical volume-of-fluid (VOF) method, included in the commercial code FLOW-3D. Wave profiles and drag forces on placed obstacles are analysed in detail. Generally, a good agreement between the laboratory and VOF results is found.}, language = {en} } @article{SchlieperBrandenburgDjuricetal.2009, author = {Schlieper, G. and Brandenburg, V. and Djuric, Z. and Damjanovic, T. and Markovic, N. and Schurgers, L. and Kr{\"u}ger, T. and Westenfeld, R. and Ackermann, D. and Haselhuhn, Angelika and Dimkovic, S. and Ketteler, M. and Floege, J. and Dimkovic, N.}, title = {Risk factors for cardiovascular calcifications in non-diabetic Caucasian haemodialysis patients}, series = {Kidney \& blood pressure research}, volume = {Vol. 32}, journal = {Kidney \& blood pressure research}, issn = {1423-0143 (E-Journal); 0378-5858 (Print); 1011-6524 (Print); 1420-4096 (Print)}, pages = {161 -- 168}, year = {2009}, language = {en} } @article{BoettcherHaselhuhnJakseetal.2012, author = {Boettcher, Martin and Haselhuhn, Angelika and Jakse, Gerhard and Brehmer, Bernhard and Kirschner-Hermanns, Ruth}, title = {Overactive bladder syndrome: an underestimated long-term problem after treatment of patients with localized prostate cancer?}, series = {BJU international}, volume = {109}, journal = {BJU international}, number = {12}, publisher = {Wiley-Blackwell}, address = {Oxford}, issn = {1365-2176 (E-Journal); 1464-410X (E-Journal); 0007-1331 (Print); 1464-4096 (Print)}, doi = {10.1111/j.1464-410X.2011.10623.x}, pages = {1824 -- 1830}, year = {2012}, abstract = {In this study we observed courses of micturition symptoms and differentiated degrees of symptoms for each point in time while also considering the impact of bothersomeness. Our data show that not only significantly more patients who have undergone BT suffer from OAB than those who have undergone RP, but also that those affected show significantly higher values for severity of OAB symptoms throughout the whole observation period of 36 months. Our data analysis further shows that variability of OAB symptoms as well as fluctuation of severity of OAB symptoms vary to a significantly higher degree after BT than after RP. Looking only at mean figures at a given point in time clearly underestimates the underlying problem. This fact is not reflected in the literature.}, language = {en} } @article{Bung2013, author = {Bung, Daniel Bernhard}, title = {Non-intrusive detection of air-water surface roughness in self-aerated chute flows}, series = {Journal of hydraulic research}, volume = {Vol. 51}, journal = {Journal of hydraulic research}, number = {Iss. 3}, publisher = {Taylor \& Francis}, address = {London}, issn = {1814-2079 (E-Journal); 0022-1686 (Print)}, pages = {322 -- 329}, year = {2013}, language = {en} } @article{DuttaHartkopfFroederWitteetal.2013, author = {Dutta, Suryendu and Hartkopf-Fr{\"o}der, Christoph and Witte, Karin and Brocke, Rainer and Mann, Ulrich}, title = {Molecular characterization of fossil palynomorphs by transmission micro-FTIR spectroscopy: implications for hydrocarbon source evaluation}, series = {International journal of coal geology}, volume = {Vol. 115}, journal = {International journal of coal geology}, publisher = {Elsevier}, address = {Amsterdam}, issn = {1872-7840 (E-Journal); 0166-5162 (Print)}, pages = {13 -- 23}, year = {2013}, language = {en} } @article{NiemuellerLakemeyerFerreinetal.2013, author = {Niem{\"u}ller, Tim and Lakemeyer, Gerhard and Ferrein, Alexander and Reuter, S. and Ewert, D. and Jeschke, S. and Pensky, D. and Karras, Ulrich}, title = {Proposal for advancements to the LLSF in 2014 and beyond}, pages = {Publ. online}, year = {2013}, language = {en} } @article{HeinzeMangPeteretal.2014, author = {Heinze, Daniel and Mang, Thomas and Peter, Karin and M{\"o}ller, Martin and Weichold, Oliver}, title = {Synthesis of low molecular weight poly(vinyl acetate) and its application as plasticizer}, series = {Journal of applied polymer science}, volume = {131}, journal = {Journal of applied polymer science}, number = {9}, publisher = {Wiley}, address = {New York}, issn = {1097-4628 (E-Journal); 0021-8995 (Print)}, doi = {10.1002/app.40226}, pages = {Article No. 40226}, year = {2014}, abstract = {Poly(vinyl acetate), PVAc, with a degree of polymerization Xn = 10 was prepared by chain-transfer radical polymerization using carbon tetrachloride and used as oligomeric plasticizer for commercial PVAc. However, the chlorinated chain ends cause a low thermal stability requiring mild Cl/H substitution. The product exhibits high thermal stability and excellent melt-compounding properties. Blends of oligomeric and commercial PVAc show single glass transition temperatures which decrease with higher oligomer content and exhibit small negative deviations from Fox' linear additivity rule. This indicates plasticization and miscibility being mainly due to entropic effects. Injection-moulded thick specimens show ductile behaviour at oligomer contents >10 wt \%, while sheets with a thickness of 0.2-0.5 mm appear flexible already at 7.5 wt \%. The oxygen permeability coefficients are an order of magnitude lower than those of low-density polyethylene. Due to the sum of their properties, the plasticized sheets present a promising alternative in the preparation of barrier materials.}, language = {en} } @article{HellwigVolkmann2003, author = {Hellwig, Angelika and Volkmann, Lutz}, title = {Maximally edge-connected digraphs}, series = {Australasian journal of combinatorics}, volume = {Vol. 27}, journal = {Australasian journal of combinatorics}, issn = {1034-4942 (E-Journal); 1034-4942 (Print)}, pages = {23 -- 32}, year = {2003}, language = {en} } @article{HellwigVolkmann2004, author = {Hellwig, Angelika and Volkmann, Lutz}, title = {Sufficient conditions for λ′-optimality in graphs of diameter 2}, series = {Discrete mathematics}, volume = {Vol. 283}, journal = {Discrete mathematics}, number = {Iss. 1-3}, issn = {1872-681X (E-Journal); 0012-365X (Print)}, pages = {113 -- 120}, year = {2004}, language = {en} } @article{HellwigVolkmann2004, author = {Hellwig, Angelika and Volkmann, Lutz}, title = {Neighborhood and degree conditions for super-edge-connected bipartite digraphs}, series = {Results in mathematics}, volume = {Vol. 45}, journal = {Results in mathematics}, number = {Iss. 1-2}, issn = {1420-9012 (E-Journal); 1422-6383 (Print)}, pages = {45 -- 58}, year = {2004}, language = {en} } @article{HellwigVolkmann2004, author = {Hellwig, Angelika and Volkmann, Lutz}, title = {Maximally local-edge-connected graphs and digraphs}, series = {Ars combinatoria}, volume = {Vol. 72}, journal = {Ars combinatoria}, issn = {0381-7032}, pages = {295 -- 306}, year = {2004}, language = {en} } @article{HellwigRautenbachVolkmann2004, author = {Hellwig, Angelika and Rautenbach, Dieter and Volkmann, Lutz}, title = {Note on the connectivity of line graphs}, series = {Information processing letters}, volume = {Vol. 91}, journal = {Information processing letters}, number = {Iss. 1}, issn = {1872-6119 (E-Journal); 0020-0190 (Print)}, pages = {7 -- 10}, year = {2004}, language = {en} } @article{XuLueMaetal.2005, author = {Xu, Jung-Ming and L{\"u}, Min and Ma, Meijie and Hellwig, Angelika}, title = {Super connectivity of line graphs}, series = {Information processing letters}, volume = {Vol. 94}, journal = {Information processing letters}, number = {Iss. 4}, issn = {1872-6119 (E-Journal); 0020-0190 (Print)}, pages = {191 -- 195}, year = {2005}, language = {en} } @article{HellwigVolkmann2005, author = {Hellwig, Angelika and Volkmann, Lutz}, title = {Sufficient conditions for graphs to be λ′-optimal, super-edge-connected, and maximally edge-connected}, series = {Journal of graph theory}, volume = {Vol. 48}, journal = {Journal of graph theory}, number = {Iss. 3}, issn = {03649024}, pages = {228 -- 246}, year = {2005}, language = {en} } @article{HellwigVolkmann2005, author = {Hellwig, Angelika and Volkmann, Lutz}, title = {Neighborhood conditions for graphs and digraphs to be maximally edge-connected}, series = {Australasian journal of combinatorics}, volume = {Vol. 33}, journal = {Australasian journal of combinatorics}, issn = {10344942 ; 22023518}, pages = {265 -- 277}, year = {2005}, language = {en} } @article{HellwigRautenbachVolkmann2005, author = {Hellwig, Angelika and Rautenbach, Dieter and Volkmann, Lutz}, title = {Cuts leaving components of given minimum order}, series = {Discrete mathematics}, volume = {Vol. 292}, journal = {Discrete mathematics}, number = {Iss. 1-3}, issn = {1872-681X (E-Journal); 0012-365X (Print)}, pages = {55 -- 65}, year = {2005}, language = {en} } @article{HellwigVolkmann2006, author = {Hellwig, Angelika and Volkmann, Lutz}, title = {Some upper bounds for the domination number}, series = {The journal of combinatorial mathematics and combinatorial computing : JCMCC}, volume = {Vol. 57}, journal = {The journal of combinatorial mathematics and combinatorial computing : JCMCC}, issn = {0835-3026}, pages = {187 -- 209}, year = {2006}, language = {en} } @article{HellwigVolkmann2006, author = {Hellwig, Angelika and Volkmann, Lutz}, title = {On connectivity in graphs with given clique number}, series = {Journal of graph theory}, volume = {Vol. 52}, journal = {Journal of graph theory}, number = {Iss. 1}, issn = {03649024 ; 10970118}, pages = {7 -- 14}, year = {2006}, language = {en} } @article{HellwigVolkmann2006, author = {Hellwig, Angelika and Volkmann, Lutz}, title = {Lower bounds on the vertex-connectivity of digraphs and graphs}, series = {Information processing letters}, volume = {Vol. 99}, journal = {Information processing letters}, number = {Iss. 2}, issn = {1872-6119 (E-Journal); 0020-0190 (Print)}, pages = {41 -- 46}, year = {2006}, language = {en} } @article{DankelmannHellwigVolkmann2007, author = {Dankelmann, Peter and Hellwig, Angelika and Volkmann, Lutz}, title = {On the connectivity of diamond-free graphs}, series = {Discrete applied mathematics}, volume = {Vol. 155}, journal = {Discrete applied mathematics}, number = {Iss. 16}, issn = {0166-218X (E-Journal); 1872-6771 (E-Journal); 0166-218X (Print)}, pages = {2111 -- 2117}, year = {2007}, language = {en} } @article{HellwigVolkmann2008, author = {Hellwig, Angelika and Volkmann, Lutz}, title = {The connectivity of a graph and its complement}, series = {Discrete applied mathematics}, volume = {Vol. 156}, journal = {Discrete applied mathematics}, number = {Iss. 17}, issn = {0166-218X (E-Journal); 1872-6771 (E-Journal); 0166-218X (Print)}, pages = {3325 -- 3328}, year = {2008}, language = {en} } @article{HellwigVolkmann2008, author = {Hellwig, Angelika and Volkmann, Lutz}, title = {Maximally edge-connected and vertex-connected graphs and digraphs : a survey}, series = {Discrete mathematics}, volume = {Vol. 308}, journal = {Discrete mathematics}, number = {Iss. 15}, issn = {1872-681X (E-Journal); 0012-365X (Print)}, pages = {3265 -- 3296}, year = {2008}, language = {en} } @article{DankelmannHellwigVolkmann2009, author = {Dankelmann, Peter and Hellwig, Angelika and Volkmann, Lutz}, title = {Inverse degree and edge-connectivity}, series = {Discrete mathematics}, volume = {Vol. 309}, journal = {Discrete mathematics}, number = {Iss. 9}, publisher = {Elsevier}, address = {Amsterdam}, issn = {1872-681X (E-Journal); 0012-365X (Print)}, pages = {2943 -- 2947}, year = {2009}, language = {en} } @article{MiyamotoHirayamaWagneretal.2013, author = {Miyamoto, Ko-ichiro and Hirayama, Yuji and Wagner, Torsten and Sch{\"o}ning, Michael Josef and Yoshinobu, Tatsuo}, title = {Visualization of enzymatic reaction in a microfluidic channel using chemical imaging sensor}, series = {Electrochimica acta}, journal = {Electrochimica acta}, publisher = {Elsevier}, address = {Amsterdam}, issn = {1873-3859 (E-Journal); 0013-4686 (Print)}, pages = {Publ. online}, year = {2013}, language = {en} } @article{DoeringKendrickLawson2013, author = {D{\"o}ring, Bernd and Kendrick, C. and Lawson, R. M.}, title = {Thermal capacity of composite floor slabs}, series = {Energy and buildings}, volume = {Vol. 67}, journal = {Energy and buildings}, publisher = {Elsevier}, address = {Amsterdam}, issn = {1872-6178 (E-Journal); 0378-7788 (Print)}, pages = {531 -- 539}, year = {2013}, language = {en} } @article{Dikta2014, author = {Dikta, Gerhard}, title = {Asymptotically efficient estimation under semi-parametric random censorship models}, series = {Journal of multivariate analysis}, volume = {124}, journal = {Journal of multivariate analysis}, publisher = {Elsevier}, address = {Amsterdam}, issn = {1095-7243 (E-Journal); 0047-259X (Print)}, doi = {10.1016/j.jmva.2013.10.002}, pages = {10 -- 24}, year = {2014}, abstract = {We study the estimation of some linear functionals which are based on an unknown lifetime distribution. The observations are assumed to be generated under the semi-parametric random censorship model (SRCM), that is, a random censorship model where the conditional expectation of the censoring indicator given the observation belongs to a parametric family. Under this setup a semi-parametric estimator of the survival function was introduced by the author. If the parametric model assumption is correct, it is known that the estimated functional which is based on this semi-parametric estimator is asymptotically at least as efficient as the corresponding one which rests on the nonparametric Kaplan-Meier estimator. In this paper we show that the estimated functional which is based on this semi-parametric estimator is asymptotically efficient with respect to the class of all regular estimators under this semi-parametric model.}, language = {en} } @article{JungStaatMueller2013, author = {Jung, Alexander and Staat, Manfred and M{\"u}ller, Wolfram}, title = {Flight style optimization in ski jumping on normal, large, and ski flying hills}, series = {Journal of biomechanics}, volume = {Vol. 47}, journal = {Journal of biomechanics}, number = {Iss. 3}, publisher = {Elsevier}, address = {Amsterdam}, issn = {1873-2380 (E-Journal); 0021-9290 (Print)}, pages = {716 -- 722}, year = {2013}, language = {en} } @article{ReisertGeisslerFloerkeetal.2013, author = {Reisert, Steffen and Geissler, Hanno and Fl{\"o}rke, Rudolf and Weiler, Christian and Wagner, Patrick and Sch{\"o}ning, Michael Josef}, title = {Characterisation of aseptic sterilisation processes using an electronic nose}, series = {International journal of nanotechnology}, volume = {Vol. 10}, journal = {International journal of nanotechnology}, number = {No. 5-7}, publisher = {Inderscience Enterprises}, address = {Gen{\`e}ve}, issn = {1475-7435 (Print) 7141-8151 (Online)}, pages = {470 -- 484}, year = {2013}, language = {en} } @article{KalbeKuropkaMeyerStorketal.1988, author = {Kalbe, Jochen and Kuropka, Rolf and Meyer-Stork, L. Sebastian and Berndt, Heinz and [u.a.],}, title = {Isolation and characterization of high-molecular mass DNA from hair shafts}, series = {Biological chemistry}, volume = {369}, journal = {Biological chemistry}, number = {1}, isbn = {0177-3593}, doi = {10.1515/bchm3.1988.369.1.413}, pages = {413 -- 416}, year = {1988}, language = {en} } @article{KuropkaMuellerHoeckeretal.1989, author = {Kuropka, Rolf and M{\"u}ller, Bettina and H{\"o}cker, Hartwig and Berndt, Heinz}, title = {Chiral stationary phases via hydrosilylation reaction of N-acryloylamino acids : I. Stationary phase with one chiral centre for high-performance liquid chromatography and development of a new derivatization pattern for amino acid enantiomers}, series = {Journal of chromatography A}, journal = {Journal of chromatography A}, number = {481}, isbn = {0021-9673}, pages = {380 -- 386}, year = {1989}, language = {en} } @article{KalbeHoeckerBerndt1989, author = {Kalbe, Jochen and H{\"o}cker, Hartwig and Berndt, Heinz}, title = {Design of enzyme reactors as chromatographic columns for racemic resolution of amino acid esters}, series = {Chromatographia}, volume = {28}, journal = {Chromatographia}, number = {3-4}, isbn = {0009-5893}, doi = {10.1007/BF02319646}, pages = {193 -- 196}, year = {1989}, language = {en} } @article{BandodkarMolinnusMirzaetal.2014, author = {Bandodkar, Amay J. and Molinnus, Denise and Mirza, Omar and Guinovart, Tomas and Windmiller, Joshua R. and Valdes-Ramirez, Gabriela and Andrade, Francisco J. and Sch{\"o}ning, Michael Josef and Wang, Joseph}, title = {Epidermal tattoo potentiometric sodium sensors with wireless signal transduction for continuous non-invasive sweat monitoring}, series = {Biosensors and bioelectronics}, volume = {54}, journal = {Biosensors and bioelectronics}, publisher = {Elsevier}, address = {Amsterdam}, issn = {1873-4235 (E-Journal); 0956-5663 (Print)}, doi = {10.1016/j.bios.2013.11.039}, pages = {603 -- 609}, year = {2014}, abstract = {This article describes the fabrication, characterization and application of an epidermal temporary-transfer tattoo-based potentiometric sensor, coupled with a miniaturized wearable wireless transceiver, for real-time monitoring of sodium in the human perspiration. Sodium excreted during perspiration is an excellent marker for electrolyte imbalance and provides valuable information regarding an individual's physical and mental wellbeing. The realization of the new skin-worn non-invasive tattoo-like sensing device has been realized by amalgamating several state-of-the-art thick film, laser printing, solid-state potentiometry, fluidics and wireless technologies. The resulting tattoo-based potentiometric sodium sensor displays a rapid near-Nernstian response with negligible carryover effects, and good resiliency against various mechanical deformations experienced by the human epidermis. On-body testing of the tattoo sensor coupled to a wireless transceiver during exercise activity demonstrated its ability to continuously monitor sweat sodium dynamics. The real-time sweat sodium concentration was transmitted wirelessly via a body-worn transceiver from the sodium tattoo sensor to a notebook while the subjects perspired on a stationary cycle. The favorable analytical performance along with the wearable nature of the wireless transceiver makes the new epidermal potentiometric sensing system attractive for continuous monitoring the sodium dynamics in human perspiration during diverse activities relevant to the healthcare, fitness, military, healthcare and skin-care domains.}, language = {en} } @article{WiegandDietrichHerteletal.2013, author = {Wiegand, Sandra and Dietrich, Sascha and Hertel, Robert and Bongaerts, Johannes and Evers, Stefan and Volland, Sonja and Daniel, Rolf and Liesegang, Heiko}, title = {RNA-Seq of Bacillus licheniformis: active regulatory RNA features expressed within a productive fermentation}, series = {BMC genomics}, volume = {Vol. 14}, journal = {BMC genomics}, publisher = {BioMed Central}, address = {London}, issn = {1471-2164}, pages = {667}, year = {2013}, language = {en} } @article{RachingerBauchStrittmatteretal.2013, author = {Rachinger, Michael and Bauch, Melanie and Strittmatter, Axel and Bongaerts, Johannes and Evers, Stefan and Maurer, Karl-Heinz and Daniel, Rolf and Liebl, Wolfgang and Liesegang, Heiko and Ehrenreich, Armin}, title = {Size unlimited markerless deletions by a transconjugative plasmid-system in Bacillus licheniformis}, series = {Journal of biotechnology}, volume = {Vol. 164}, journal = {Journal of biotechnology}, number = {Iss. 4}, publisher = {Elsevier}, address = {Amsterdam}, issn = {1873-4863 (E-Journal); 0168-1656 (Print)}, pages = {365 -- 369}, year = {2013}, language = {en} } @article{VoigtSchroeterJuergenetal.2013, author = {Voigt, Birgit and Schroeter, Rebecca and J{\"u}rgen, Britta and Albrecht, Dirk and Evers, Stefan and Bongaerts, Johannes and Maurer, Karl-Heinz and Schweder, Thomas and Hecker, Michael}, title = {The response of Bacillus licheniformis to heat and ethanol stress and the role of the SigB regulon}, series = {Proteomics}, volume = {Vol. 13}, journal = {Proteomics}, number = {Iss. 14}, publisher = {Wiley}, address = {Weinheim}, issn = {1615-9861 (E-Journal); 1615-9853 (Print)}, pages = {2140 -- 2146}, year = {2013}, language = {en} } @article{WilmingBegemannKuhneetal.2013, author = {Wilming, Anja and Begemann, Jens and Kuhne, Stefan and Regestein, Lars and Bongaerts, Johannes and Evers, Stefan and Maurer, Karl-Heinz and B{\"u}chs, Jochen}, title = {Metabolic studies of γ-polyglutamic acid production in Bacillus licheniformis by small-scale continuous cultivations}, series = {Biochemical engineering journal}, volume = {Vol. 73}, journal = {Biochemical engineering journal}, publisher = {Elsevier}, address = {Amsterdam}, issn = {1873-295X (E-Journal); 1369-703X (Print)}, pages = {29 -- 37}, year = {2013}, language = {en} } @article{ScheeleOertelBongaertsetal.2013, author = {Scheele, Sandra and Oertel, Dan and Bongaerts, Johannes and Evers, Stefan and Hellmuth, Hendrik and Maurer, Karl-Heinz and Bott, Michael and Freudl, Roland}, title = {Secretory production of an FAD cofactor-containing cytosolic enzyme (sorbitol-xylitol oxidase from Streptomyces coelicolor) using the twin-arginine translocation (Tat) pathway of Corynebacterium glutamicum}, series = {Microbial biotechnology}, journal = {Microbial biotechnology}, publisher = {Wiley-Blackwell}, address = {Oxford}, issn = {1751-7915}, pages = {202 -- 206}, year = {2013}, language = {en} } @article{BorgmeierBongaertsMeinhardt2012, author = {Borgmeier, Claudia and Bongaerts, Johannes and Meinhardt, Friedhelm}, title = {Genetic analysis of the Bacillus licheniformis degSU operon and the impact of regulatory mutations on protease production}, series = {Journal of biotechnology}, volume = {159}, journal = {Journal of biotechnology}, number = {1-2}, publisher = {Elsevier}, address = {Amsterdam}, issn = {1873-4863 (E-Journal); 0168-1656 (Print)}, doi = {10.1016/j.jbiotec.2012.02.011}, pages = {12 -- 20}, year = {2012}, abstract = {Disruption experiments targeted at the Bacillus licheniformis degSU operon and GFP-reporter analysis provided evidence for promoter activity immediately upstream of degU. pMutin mediated concomitant introduction of the degU32 allele - known to cause hypersecretion in Bacillus subtilis - resulted in a marked increase in protease activity. Application of 5-fluorouracil based counterselection through establishment of a phosphoribosyltransferase deficient Δupp strain eventually facilitated the marker-free introduction of degU32 leading to further protease enhancement achieving levels as for hypersecreting wild strains in which degU was overexpressed. Surprisingly, deletion of rapG - known to interfere with DegU DNA-binding in B. subtilis - did not enhance protease production neither in the wild type nor in the degU32 strain. The combination of degU32 and Δupp counterselection in the type strain is not only equally effective as in hypersecreting wild strains with respect to protease production but furthermore facilitates genetic strain improvement aiming at biological containment and effectiveness of biotechnological processes.}, language = {en} } @article{BongaertsEsserLorbachetal.2011, author = {Bongaerts, Johannes and Esser, Simon and Lorbach, Volker and Al-Momani, L{\´o}ay and M{\"u}ller, Michael A. and Franke, Dirk and Grondal, Christoph and Kurutsch, Anja and Bujnicki, Robert and Takors, Ralf and Raeven, Leon and Wubbolts, Marcel and Bovenberg, Roel and Nieger, Martin and Sch{\"u}rmann, Melanie and Trachtmann, Natalie and Kozak, Stefan and Sprenger, Georg A. and M{\"u}ller, Michael}, title = {Diversity-oriented production of metabolites derived from chorismate and their use in organic synthesis}, series = {Angewandte Chemie International Edition}, volume = {Vol. 50}, journal = {Angewandte Chemie International Edition}, number = {Iss. 34}, publisher = {Wiley}, address = {Weinheim}, issn = {1521-3773 (E-Journal); 0570-0833 (Print); 1433-7851 (Print)}, pages = {7781 -- 7786}, year = {2011}, language = {en} } @article{DeppeKlatteBongaertsetal.2011, author = {Deppe, Veronika Maria and Klatte, Stephanie and Bongaerts, Johannes and Maurer, Karl-Heinz and O'Connell, Timothy and Meinhardt, Friedhelm}, title = {Genetic control of Amadori product degradation in Bacillus subtilis via regulation of frlBONMD expression by FrlR}, series = {Applied and environmental microbiology}, volume = {Vol. 77}, journal = {Applied and environmental microbiology}, number = {No. 9}, publisher = {American Society of Mechanical Engineers (ASME)}, address = {New York}, issn = {1098-5336 (E-Journal); 0003-6919 (Print); 0099-2240 (Print)}, pages = {2839 -- 2846}, year = {2011}, language = {en} } @article{DeppeBongaertsO'Connelletal.2011, author = {Deppe, Veronika Maria and Bongaerts, Johannes and O'Connell, Timothy and Maurer, Karl-Heinz and Meinhardt, Friedhelm}, title = {Enzymatic deglycation of Amadori products in bacteria}, series = {Applied microbiology and biotechnology}, volume = {Vol. 90}, journal = {Applied microbiology and biotechnology}, number = {Iss. 2}, publisher = {Springer}, address = {Berlin}, issn = {1432-0614 (E-Journal); 0171-1741 (Print); 0175-7598 (Print); 0340-2118 (Print)}, pages = {399 -- 406}, year = {2011}, language = {en} } @article{DegeringEggertPulsetal.2010, author = {Degering, Christian and Eggert, Thorsten and Puls, Michael and Bongaerts, Johannes and Evers, Stefan and Maurer, Karl-Heinz and Jaeger, Karl-Erich}, title = {Optimization of protease secretion in Bacillus subtilis and Bacillus licheniformis by screening of homologous and herologous signal peptides}, series = {Applied and environmental microbiology}, volume = {76}, journal = {Applied and environmental microbiology}, number = {19}, publisher = {American Society for Microbiology}, address = {Washington, DC}, issn = {1098-5336 (E-Journal); 0003-6919 (Print); 0099-2240 (Print)}, doi = {10.1128/AEM.01146-10}, pages = {6370 -- 6378}, year = {2010}, abstract = {Bacillus subtilis and Bacillus licheniformis are widely used for the large-scale industrial production of proteins. These strains can efficiently secrete proteins into the culture medium using the general secretion (Sec) pathway. A characteristic feature of all secreted proteins is their N-terminal signal peptides, which are recognized by the secretion machinery. Here, we have studied the production of an industrially important secreted protease, namely, subtilisin BPN′ from Bacillus amyloliquefaciens. One hundred seventy-three signal peptides originating from B. subtilis and 220 signal peptides from the B. licheniformis type strain were fused to this secretion target and expressed in B. subtilis, and the resulting library was analyzed by high-throughput screening for extracellular proteolytic activity. We have identified a number of signal peptides originating from both organisms which produced significantly increased yield of the secreted protease. Interestingly, we observed that levels of extracellular protease were improved not only in B. subtilis, which was used as the screening host, but also in two different B. licheniformis strains. To date, it is impossible to predict which signal peptide will result in better secretion and thus an improved yield of a given extracellular target protein. Our data show that screening a library consisting of homologous and heterologous signal peptides fused to a target protein can identify more-effective signal peptides, resulting in improved protein export not only in the original screening host but also in different production strains.}, language = {en} } @article{PolenKraemerBongaertsetal.2005, author = {Polen, T. and Kr{\"a}mer, Marco and Bongaerts, Johannes and Wubbolts, Marcel and Wendisch, V. F.}, title = {The global gene expression response of Escherichia coli to L-phenylalanine}, series = {Journal of biotechnology}, volume = {Vol. 115}, journal = {Journal of biotechnology}, number = {Iss. 3}, issn = {1873-4863 (E-Journal); 0168-1656 (Print)}, pages = {221 -- 237}, year = {2005}, language = {en} } @article{KraemerBongaertsBovenbergetal.2003, author = {Kr{\"a}mer, Marco and Bongaerts, Johannes and Bovenberg, Roel and Kremer, Susanne and M{\"u}ller, Ulrike and Orf, Sonja and Wubbolts, Marcel and Raeven, Leon}, title = {Metabolic engineering for microbial production of shikimic acid}, series = {Metabolic engineering}, volume = {Vol. 5}, journal = {Metabolic engineering}, number = {Iss. 4}, issn = {1096-7184 (E-Journal); 1096-7176 (Print)}, pages = {277 -- 283}, year = {2003}, language = {en} } @article{GerigkMaassKreutzeretal.2002, author = {Gerigk, M. and Maaß, D. and Kreutzer, A. and Sprenger, G. and Bongaerts, Johannes and Wubbolts, Marcel and Takors, Ralf}, title = {Enhanced pilot-scale fed-batch L-phenylalanine production with recombinant Escherichia coli by fully integrated reactive extraction}, series = {Bioprocess and biosystems engineering}, volume = {Vol. 25}, journal = {Bioprocess and biosystems engineering}, number = {Iss. 1}, issn = {1432-0797 (E-Journal); 1615-7605 (E-Journal); 0178-515X (Print); 1615-7591 (Print)}, pages = {43 -- 52}, year = {2002}, language = {en} } @article{GerigkBujnickiGanpoNkwenkwaetal.2002, author = {Gerigk, M. and Bujnicki, R. and Ganpo-Nkwenkwa, E. and Bongaerts, Johannes and Sprenger, G. and Takors, Ralf}, title = {Process control for enhanced L-phenylalanine production using different recombinant Escherichia coli strains}, series = {Biotechnology and bioengineering}, volume = {Vol. 80}, journal = {Biotechnology and bioengineering}, number = {Iss. 7}, issn = {1097-0290 (E-Journal); 0006-3592 (Print)}, pages = {746 -- 754}, year = {2002}, language = {en} } @article{BongaertsBovenbergKraemeretal.2002, author = {Bongaerts, Johannes and Bovenberg, Roel and Kr{\"a}mer, Marco and M{\"u}ller, Ulrike and Raeven, Leon and Wubbolts, Marcel}, title = {Metabolic engineering to produce fine chemicals in Escherichia coli}, series = {Chemie - Ingenieur - Technik (CIT)}, volume = {Vol. 74}, journal = {Chemie - Ingenieur - Technik (CIT)}, number = {Iss. 5}, issn = {1522-2640 (E-Journal); 0009-286X (Print)}, pages = {694}, year = {2002}, language = {en} } @article{SchmitzHirschBongaertsetal.2002, author = {Schmitz, M. and Hirsch, E. and Bongaerts, Johannes and Takors, Ralf}, title = {Pulse experiments as a prerequisite for the quantification of in vivo enzyme kinetics in aromatic amino acid pathway of Eschericia coli}, series = {Biotechnology progress}, volume = {Vol. 18}, journal = {Biotechnology progress}, number = {Iss. 5}, issn = {1520-6033 (E-Journal); 8756-7938 (Print)}, pages = {935 -- 941}, year = {2002}, language = {en} } @article{BongaertsKraemerMuelleretal.2001, author = {Bongaerts, Johannes and Kr{\"a}mer, Marco and M{\"u}ller, Ulrike and Raeven, Leon and Wubbolts, Marcel}, title = {Metabolic engineering for microbial production of aromatic amino acids and derived compounds}, series = {Metabolic engineering}, volume = {Vol. 3}, journal = {Metabolic engineering}, number = {Iss. 4}, issn = {1096-7184 (E-Journal); 1096-7176 (Print)}, pages = {289 -- 300}, year = {2001}, language = {en} } @article{JossekBongaertsSprenger2001, author = {Jossek, Ralf and Bongaerts, Johannes and Sprenger, Georg A.}, title = {Characterization of a new feedback-resistant 3-deoxy-D-arabinoheptulosonate 7-phosphate synthase AroF of Escherichia coli}, series = {FEMS microbiology letters}, volume = {Vol. 202}, journal = {FEMS microbiology letters}, number = {Iss. 1}, issn = {1574-6968}, pages = {145 -- 148}, year = {2001}, language = {en} } @article{MuellerBongaertsBovenbergetal.2001, author = {M{\"u}ller, Ulrike and Bongaerts, Johannes and Bovenberg, Roel and Jossek, Ralf and Kr{\"a}mer, Marco and Linnemann, J. and M{\"u}schen, S. and Ritterbecks, S. and Sprenger, G. and Wubbolts, Marcel}, title = {Metabolic engineering to produce fine chemicals in Escherichia coli}, series = {Mededelingen van de Faculteit Landbouwwetenschappen, Rijksuniversiteit Gent}, volume = {66 (3a)}, journal = {Mededelingen van de Faculteit Landbouwwetenschappen, Rijksuniversiteit Gent}, issn = {0035-533x}, pages = {215 -- 217}, year = {2001}, language = {en} } @article{WackwitzBongaertsGoodmanetal.1999, author = {Wackwitz, B. and Bongaerts, Johannes and Goodman, S. D. and Unden, Gottfried}, title = {Growth phase-dependent regulation of nuoA-N expression in Escherichia coli K-12 by the Fis protein: upstream binding sites and bioenergetic significance}, series = {Molecular and general genetics : MGG}, volume = {Vol. 262}, journal = {Molecular and general genetics : MGG}, number = {Iss. 4 - 5}, issn = {1617-4623 (E-Journal); 1617-4615 (Print)}, pages = {876 -- 883}, year = {1999}, language = {en} } @article{ZientzBongaertsUnden1998, author = {Zientz, Evelyn and Bongaerts, Johannes and Unden, Gottfried}, title = {Fumarate regulation of gene expression in Escherichia coli by the DcuSR (dcuSR genes) two-component regulatory system}, series = {Journal of bacteriology}, volume = {Vol. 180}, journal = {Journal of bacteriology}, number = {No. 20}, issn = {1098-5530 (E-Journal); 0021-9193 (Print)}, pages = {5421 -- 5425}, year = {1998}, language = {en} } @article{UndenBongaerts1997, author = {Unden, Gottfried and Bongaerts, Johannes}, title = {Alternative respiratory pathways of Escherichia coli: energetics and transcriptional regulation in response to electron acceptors}, series = {Biochimica et biophysica acta (BBA) - Bioenergetics}, volume = {Vol. 1320}, journal = {Biochimica et biophysica acta (BBA) - Bioenergetics}, number = {Iss. 3}, issn = {1879-2650 (E-Journal); 0005-2728 (Print)}, pages = {217 -- 234}, year = {1997}, language = {en} } @article{TranBongaertsVladetal.1997, author = {Tran, Quang Hon and Bongaerts, Johannes and Vlad, Dorina and Unden, Gottfried}, title = {Requirement for the proton-pumping NADH dehydrogenase I of Escherichia coli in respiration of NADH to fumarate and its bioenergetic implications}, series = {European journal of biochemistry}, volume = {Vol. 244}, journal = {European journal of biochemistry}, number = {Iss. 1}, issn = {0014-2956}, pages = {155 -- 160}, year = {1997}, language = {en} } @article{WissenbachSixBongaertsetal.1995, author = {Wissenbach, U. and Six, S. and Bongaerts, Johannes and Ternes, D. and Steinwachs, S. and Unden, G.}, title = {A third periplasmic transport system for l-arginine in Escherichia coli: molecular characterization of the artPIQMJ genes, arginine binding and transport}, series = {Molecular microbiology}, volume = {Vol. 17}, journal = {Molecular microbiology}, number = {Iss. 4}, issn = {1365-2958 (E-Journal); 0950-382x (Print)}, pages = {675 -- 686}, year = {1995}, language = {en} } @article{UndenBeckerBongaertsetal.1995, author = {Unden, G. and Becker, S. and Bongaerts, Johannes and Holighaus, G. and Schirawski, J. and Six, S.}, title = {O2-sensing and O2-dependent gene regulation in facultatively anaerobic bacteria}, series = {Archives of microbiology}, volume = {Vol. 164}, journal = {Archives of microbiology}, number = {Iss. 2}, issn = {1432-072X (E-Journal); 0003-9276 (Print); 0302-8933 (Print)}, pages = {81 -- 90}, year = {1995}, language = {en} } @article{BongaertsZoschkeWeidneretal.1995, author = {Bongaerts, Johannes and Zoschke, Sascha and Weidner, Uwe and Linden, Gottfried}, title = {Transcriptional regulation of the proton translocating NADH}, series = {Molecular microbiology}, volume = {Vol. 16}, journal = {Molecular microbiology}, number = {Iss. 3}, issn = {1365-2958 (E-Journal); 0950-382x (Print)}, pages = {521 -- 534}, year = {1995}, language = {en} } @article{UndenBeckerBongaertsetal.1994, author = {Unden, G. and Becker, S. and Bongaerts, Johannes and Schirawski, J. and Six, S.}, title = {Oxygen regulated gene expression in facultatively anaerobic bacteria}, series = {Antonie van Leeuwenhoek}, volume = {Vol. 66}, journal = {Antonie van Leeuwenhoek}, number = {Iss. 1-3}, issn = {0003-6072 (Print) ; 1572-9699 (online)}, pages = {3 -- 22}, year = {1994}, language = {en} } @article{BoehmHellmannsBackesetal.2006, author = {B{\"o}hm, Stefan and Hellmanns, Mark and Backes, Andreas and Dilger, Klaus}, title = {Lock-in thermography based NDT of parts for the automotive industry}, series = {Journal of adhesion and interface}, volume = {Vol. 7}, journal = {Journal of adhesion and interface}, number = {No. 4}, pages = {10 -- 12}, year = {2006}, language = {en} } @article{HellmannsBoehmDilger2006, author = {Hellmanns, Mark and B{\"o}hm, Stefan and Dilger, Klaus}, title = {Manual applications of adhesives}, series = {Journal of adhesion and interface}, volume = {Vol. 7}, journal = {Journal of adhesion and interface}, number = {No. 4}, pages = {24 -- 27}, year = {2006}, language = {en} } @article{Laack2013, author = {Laack, Walter van}, title = {Our world is well ordered in measurement and number : or why natural constants are as they are}, series = {American Journal of Humanities and Social Sciences (AHSS)}, volume = {1}, journal = {American Journal of Humanities and Social Sciences (AHSS)}, number = {4}, issn = {2329-079X}, doi = {10.11634/232907811301390}, pages = {219 -- 221}, year = {2013}, abstract = {All the important natural constants can be logically explained with and derived from the first four ordinal numbers, 1, 2, 3 and 4, its addition to ten and finally the standard values for obviously maximal feasibility Ω and the optimum in our world, the Golden Section (GS), i.e. the number sequences 273 and 618. They both are the first three numbers of irrational results by an arithmetical transformation of simple geometrical relationships by creating multiplicity out of singularity. Both of them show that the infinite is inherent in finiteness and explain in a simple way the smallest deviations and fluctuations between the physical AS-IS state and the obvious spiritual ideal behind: Wherever we look in this world, and especially in important key-positions, we regularly find these sequences. All of the above mentioned numbers so seem to be key players in our world, what can be demonstrated by the derivation of natural constants.}, language = {en} } @article{Schnitzler2009, author = {Schnitzler, Thomas}, title = {Cultivation of hybridoma cell line CF-10H5 (DSMZ ACC477)}, series = {Application notes / Sartorius stedim biotech}, journal = {Application notes / Sartorius stedim biotech}, pages = {1 -- 4}, year = {2009}, language = {en} } @article{WincklerKruegerSchnitzleretal.2014, author = {Winckler, Silvia and Krueger, Rolf and Schnitzler, Thomas and Zang, Werner and Fischer, Rainer and Biselli, Manfred}, title = {A sensitive monitoring system for mammalian cell cultivation processes: a PAT approach}, series = {Bioprocess and biosystems engineering}, volume = {37}, journal = {Bioprocess and biosystems engineering}, number = {5}, publisher = {Springer}, address = {Berlin, Heidelberg}, issn = {1615-7591 (Print) 1615-7605 (Online)}, doi = {10.1007/s00449-013-1062-8}, pages = {901 -- 912}, year = {2014}, abstract = {Biopharmaceuticals such as antibodies are produced in cultivated mammalian cells, which must be monitored to comply with good manufacturing practice. We, therefore, developed a fully automated system comprising a specific exhaust gas analyzer, inline analytics and a corresponding algorithm to precisely determine the oxygen uptake rate, carbon dioxide evolution rate, carbon dioxide transfer rate, transfer quotient and respiratory quotient without interrupting the ongoing cultivation, in order to assess its reproducibility. The system was verified using chemical simulation experiments and was able to measure the respiratory activity of hybridoma cells and DG44 cells (derived from Chinese hamster ovary cells) with satisfactory results at a minimum viable cell density of ~2.0 × 10⁵ cells ml⁻¹. The system was suitable for both batch and fed-batch cultivations in bubble-aerated and membrane-aerated reactors, with and without the control of pH and dissolved oxygen.}, language = {en} } @article{Staat2013, author = {Staat, Manfred}, title = {Limit and shakedown analysis under uncertainty}, series = {International journal of computational methods : IJCM}, journal = {International journal of computational methods : IJCM}, publisher = {World Scientific Publishing}, address = {Singapore}, issn = {0219-8762}, pages = {Publ. online}, year = {2013}, language = {en} } @article{Laack2013, author = {Laack, Walter van}, title = {Why natural constants are as they are}, series = {British journal of arts and social sciences}, volume = {Vol. 15}, journal = {British journal of arts and social sciences}, number = {Nr. 2}, publisher = {BritishJournal Publ. Inc}, address = {London}, issn = {2046-9578 (E-Journal)}, pages = {198 -- 203}, year = {2013}, language = {en} } @article{IkenAhlbornGerlachetal.2013, author = {Iken, Heiko and Ahlborn, K. and Gerlach, F. and Vonau, W. and Zander, W. and Schubert, J. and Sch{\"o}ning, Michael Josef}, title = {Development of redox glasses and subsequent processing by means of pulsed laser deposition for realizing silicon-based thin-film sensors}, series = {Electrochimica acta}, journal = {Electrochimica acta}, publisher = {Elsevier}, address = {Amsterdam}, issn = {1873-3859 (E-Journal); 0013-4686 (Print)}, pages = {Available online 30.8.2013}, year = {2013}, language = {en} } @article{MeyerStorkHoeckerBerndt1992, author = {Meyer-Stork, L. Sebastian and H{\"o}cker, Hartwig and Berndt, Heinz}, title = {Syntheses and reactions of urethanes of cellobiose and cellulose-containing uretdione groups}, series = {Journal of applied polymer science}, volume = {44}, journal = {Journal of applied polymer science}, number = {6}, issn = {1097-4628}, pages = {1043 -- 1049}, year = {1992}, language = {en} } @article{HemmerlingMerschenzQuackWunderlich1988, author = {Hemmerling, H.-J. and Merschenz-Quack, Angelika and Wunderlich, H.}, title = {Crystal structures of indeno[1,2-d]imidazoles. XIth European Crystallographic Meeting, Vienna 1988}, series = {Zeitschrift f{\"u}r Kristallographie - Crystalline Materials}, volume = {185}, journal = {Zeitschrift f{\"u}r Kristallographie - Crystalline Materials}, number = {H. 1-4}, issn = {2196-7105 (E-Books); 2194-4946 (Print)}, pages = {256}, year = {1988}, language = {en} } @article{RamazaniLiMukherjeeetal.2013, author = {Ramazani, Ali and Li, Yang and Mukherjee, Krishnendu and Prahl, Ulrich and Bleck, Wolfgang and Abdurakhmanov, Aydemir and Schleser, Markus and Reisgen, Uwe}, title = {Microstructure evolution simulation in hot rolled DP600 steel during gas metal arc welding}, series = {Computational materials science}, volume = {Vol. 68}, journal = {Computational materials science}, publisher = {Elsevier}, address = {Amsterdam}, issn = {1879-0801 (E-Book); 0927-0256 (Print)}, pages = {107 -- 116}, year = {2013}, language = {en} } @article{ReisgenSchleserMokrovetal.2012, author = {Reisgen, Uwe and Schleser, Markus and Mokrov, Oleg and Zabirov, Alexander and F{\"u}ssel, Uwe and Schnick, Michael and Hertel, Martin and Jaeckel, Sebastian}, title = {Modelling and visualisation of the GMA process}, series = {Welding and Cutting}, volume = {11}, journal = {Welding and Cutting}, number = {4}, publisher = {DVS Verlag}, address = {D{\"u}sseldorf}, issn = {1612-3433}, pages = {242 -- 249}, year = {2012}, language = {en} } @article{ReisgenSchleserAbdurakhmanovetal.2012, author = {Reisgen, Uwe and Schleser, Markus and Abdurakhmanov, Aydemir and Gumenyuk, Andrey}, title = {Measuring of plasma properties induced by non-vacuum electron beam welding}, series = {Physics of plasma}, volume = {19}, journal = {Physics of plasma}, number = {1}, publisher = {AIP Publishing}, address = {Melville, NY}, issn = {1089-7674 (E-Journal); 1070-664X (Print)}, doi = {10.1063/1.3675874}, pages = {1 -- 7}, year = {2012}, abstract = {Electron beam plasma measurement was realised by means of DIABEAM system invented by ISF RWTH Aachen. The Langmuir probe method is used for measurement. The relative simplicity of the method and the possibility of dispersion of high power on the probe allow its application for the investigation of high-power electron beams. The key element of the method is a rotating thin tungsten wire, which intersects the beam transversely on its axis and collects part of the current by itself. The signals, which are registered in the DIABEAM as a voltage, were taken in the form of amplitude. The conversion of the probe current into the distribution along the beam radius was realised using the Abel's method. A voltage-current characteristic was built for the beam current. The local electron density as well as the electron temperature, the floating potential and the plasma potential were measured and calculated by means of this characteristic.}, language = {en} } @article{ReisgenSchleserAbdurakhmanovetal.2012, author = {Reisgen, Uwe and Schleser, Markus and Abdurakhmanov, Aydemir and Turichin, Gleb and Valdaitseva, Elena and Bach, Friedrich-Wilhelm and Hassel, Thomas and Beniyashi, Alexander}, title = {Investigation of factors influencing the formation of weld defects in non-vacuum electron beam welding}, series = {The Paton welding journal}, volume = {2012}, journal = {The Paton welding journal}, number = {2}, publisher = {Paton Publishing House}, address = {Kiev}, issn = {0957-798X}, pages = {11 -- 18}, year = {2012}, abstract = {The influence of welding condition parameters and properties of material on formation of defects, such as humping and undercuts, in non-vacuum electron beam welding was investigated. The influence of separate welding parameters on the quality of welds was determined.}, language = {en} } @article{ReisgenOlschokJakobsetal.2012, author = {Reisgen, Uwe and Olschok, Simon and Jakobs, Stefan and Schleser, Markus and Mokrov, Oleg and Rossiter, Eduardo}, title = {Laser beam submerged arc hybrid welding}, series = {Physics procedia}, volume = {39}, journal = {Physics procedia}, publisher = {Elsevier}, address = {Amsterdam}, issn = {1875-3892}, doi = {10.1016/j.phpro.2012.10.016}, pages = {75 -- 83}, year = {2012}, abstract = {The laser beam-submerged arc hybrid welding method originates from the knowledge that, with increasing penetration depth, the laser beam process has a tendency to pore formation in the lower weld regions. The coupling with the energy-efficient submerged-arc process improves degassing and reduces the tendency to pore formation. The high deposition rate of the SA process in combination with the laser beam process offers, providing the appropriate choice of weld preparation, the possibility of welding plates with a thickness larger than 20° mm in a single pass, and also of welding thicker plates with the double-sided single pass technique.}, language = {en} } @article{ReisgenSchleserMokrovetal.2012, author = {Reisgen, Uwe and Schleser, Markus and Mokrov, Oleg and Ahmed, Essam}, title = {Optimization of laser welding of DP/TRIP steel sheets using statistical approach}, series = {Optics and laser technology}, volume = {44}, journal = {Optics and laser technology}, number = {1}, publisher = {Elsevier}, address = {Amsterdam}, issn = {1879-2545 (E-Journal); 0030-3992 (Print); 0308-4280 (Print)}, doi = {10.1016/j.optlastec.2011.06.028}, pages = {255 -- 262}, year = {2012}, abstract = {Generally, the quality of a weld joint is directly influenced by the welding input parameter settings. Selection of proper process parameters is important to obtain the desired weld bead profile and quality. In this research work, numerical and graphical optimization techniques of the CO2 laser beam welding of dual phase (DP600)/transformation induced plasticity (TRIP700) steel sheets were carried out using response surface methodology (RSM) based on Box-Behnken design. The procedure was established to improve the weld quality, increase the productivity and minimize the total operation cost by considering the welding parameters range of laser power (2-2.2 kW), welding speed (40-50 mm/s) and focus position (-1 to 0 mm). It was found that, RSM can be considered as a powerful tool in experimental welding optimization, even when the experimenter does not have a model for the process. Strong, efficient and low cost weld joints could be achieved using the optimum welding conditions.}, language = {en} } @article{ReisgenSchleserMokrovetal.2012, author = {Reisgen, Uwe and Schleser, Markus and Mokrov, Oleg and Ahmed, Essam}, title = {Statistical modeling of laser welding of DP/TRIP steel sheets}, series = {Optics and laser technology}, volume = {44}, journal = {Optics and laser technology}, number = {1}, publisher = {Elsevier}, address = {Amsterdam}, issn = {1879-2545 (E-Journal); 0030-3992 (Print); 0308-4280 (Print)}, doi = {10.1016/j.optlastec.2011.05.025}, pages = {92 -- 101}, year = {2012}, abstract = {In this research work, a statistical analysis of the CO2 laser beam welding of dual phase (DP600)/transformation induced plasticity (TRIP700) steel sheets was done using response surface methodology. The analysis considered the effect of laser power (2-2.2 kW), welding speed (40-50 mm/s) and focus position (-1 to 0 mm) on the heat input, the weld bead geometry, uniaxial tensile strength, formability limited dome height and welding operation cost. The experimental design was based on Box-Behnken design using linear and quadratic polynomial equations for predicting the mathematical models. The results indicate that the proposed models predict the responses adequately within the limits of welding parameters being used and the welding speed is the most significant parameter during the welding process.}, language = {en} } @article{ReisgenSchleserMokrovetal.2011, author = {Reisgen, Uwe and Schleser, Markus and Mokrov, Oleg and Zabirov, Alexander}, title = {Virtual welding equipment for simulation of GMAW processes with integration of power source regulation}, series = {Frontiers of materials science}, volume = {Vol. 5}, journal = {Frontiers of materials science}, number = {Iss. 2}, publisher = {Springer}, address = {Berlin}, issn = {2095-0268 (E-Journal); 2095-025X (Print)}, pages = {79 -- 89}, year = {2011}, language = {en} } @article{RoesnerScheikOlowinskyetal.2011, author = {Roesner, Andreas and Scheik, Sven and Olowinsky, Alexander and Gillner, Arnold and Reisgen, Uwe and Schleser, Markus}, title = {Laser assisted joining of plastic metal hybrids}, series = {Lasers in manufacturing 2011 : proceedings of the sixth International WLT Conference on Lasers in Manufacturing, Munich, May 23 - 26 2011. (Physics procedia ; Vol. 12 (2011), Part B)}, journal = {Lasers in manufacturing 2011 : proceedings of the sixth International WLT Conference on Lasers in Manufacturing, Munich, May 23 - 26 2011. (Physics procedia ; Vol. 12 (2011), Part B)}, publisher = {Elsevier}, address = {Amsterdam}, organization = {International WLT Conference on Lasers in Manufacturing <6, M{\"u}nchen, 2011>}, issn = {1875-3892 (E-Journal); 1875-3884 (Print)}, pages = {370 -- 377}, year = {2011}, language = {en} } @article{RoesnerScheikOlowinskyetal.2011, author = {Roesner, Andreas and Scheik, Sven and Olowinsky, Alexander and Gillner, Arnold and Propawe, Reinhart and Schleser, Markus and Reisgen, Uwe}, title = {Innovative approach of joining hybrid components}, series = {Journal of laser applications}, volume = {Vol. 23}, journal = {Journal of laser applications}, number = {Iss. 3}, publisher = {Laser Institute of America}, address = {Orlando, Fla.}, issn = {1042-346X}, pages = {32007}, year = {2011}, language = {en} } @article{ReisgenSchleserMokrovetal.2011, author = {Reisgen, Uwe and Schleser, Markus and Mokrov, Oleg and Ahmed, Essam}, title = {Numerical and experimental investigation of tensile behavior of laser beam welded TRIP700 steel}, series = {ISIJ international}, volume = {Vol. 51}, journal = {ISIJ international}, number = {No. 3}, publisher = {ISIJ}, address = {Tōkyō}, organization = {Iron and Steel Institute of Japan (ISIJ)}, issn = {1347-5460 (E-Journal); 0915-1559 (Print)}, pages = {429 -- 434}, year = {2011}, language = {en} } @article{GlowaniaGriesSchoeneetal.2011, author = {Glowania, Michael and Gries, Thomas and Schoene, Jens and Schleser, Markus and Reisgen, Uwe}, title = {Innovative coating technology for textile reinforcements of concrete applications}, series = {13th International Congress on Polymers in Concrete : 10 - 12 February 2010, Funchal, Madeira, Portugal.(Key engineering materials. Vol. 466)}, journal = {13th International Congress on Polymers in Concrete : 10 - 12 February 2010, Funchal, Madeira, Portugal.(Key engineering materials. Vol. 466)}, publisher = {Trans Tech Publications}, address = {B{\"a}ch}, organization = {International Congress Polymers in Concrete <13, 2010, Funchal, Madeira>}, isbn = {978-3-03785-008-4}, issn = {1013-9826 (E-Journal) ; 0252-1059 (Print)}, pages = {167 -- 173}, year = {2011}, language = {en} } @article{MukherjeeRamazaniYangetal.2011, author = {Mukherjee, Krishnendu and Ramazani, Ali and Yang, Li and Prahl, Ulrich and Bleck, Wolfgang and Reisgen, Uwe and Schleser, Markus and Abdurakhmanov, Aydemir}, title = {Characterization of gas metal arc welded hot rolled DP600 steel}, series = {Steel research international}, volume = {Vol. 82}, journal = {Steel research international}, number = {Iss. 12}, publisher = {Wiley}, address = {Weinheim}, issn = {1869-344X (E-Book); 1611-3683 (Print)}, pages = {1408 -- 1416}, year = {2011}, language = {en} } @article{MukherjeePrahlBlecketal.2010, author = {Mukherjee, Krishnendu and Prahl, Ulrich and Bleck, Wolfgang and Reisgen, Uwe and Schleser, Markus and Abdurakhmanov, Aydemir}, title = {Characterization and modelling techniques for gas metal arc welding of DP 600 sheet steels}, series = {Materialwissenschaft und Werkstofftechnik}, volume = {41}, journal = {Materialwissenschaft und Werkstofftechnik}, number = {11}, publisher = {Wiley-VCH}, address = {Weinheim}, issn = {1521-4052}, doi = {10.1002/mawe.201000692}, pages = {972 -- 983}, year = {2010}, abstract = {The objectives of the present work are to characterize the Gas Metal Arc Welding process of DP 600 sheet steel and to summarize the modelling techniques. The time-temperature evolution during the welding cycle was measured experimentally and modelled with the softwaretool SimWeld. To model the phase transformations during the welding cycle dilatometer tests were done to quantify the parameters for phase field modelling by MICRESS®. The important input parameters are interface mobility, nucleation density, etc. A contribution was made to include austenite to bainite transformation in MICRESS®. This is useful to predict the microstructure in the fast cooling segments. The phase transformation model is capable to predict the microstructure along the heating and cooling cycles of welding. Tensile tests have shown the evidence of failure at the heat affected zone, which has the ferrite-tempered martensite microstructure.}, language = {en} } @article{ReisgenSchleserMokrovetal.2010, author = {Reisgen, Uwe and Schleser, Markus and Mokrov, Oleg and Ahmed, Essam}, title = {Uni- and bi-axial deformation behavior of laser welded advanced high strength steel sheets}, series = {Journal of materials processing technology}, volume = {210}, journal = {Journal of materials processing technology}, number = {15}, publisher = {Elsevier}, address = {Amsterdam}, issn = {0924-0136}, doi = {http10.1016/j.jmatprotec.2010.08.003}, pages = {2188 -- 2196}, year = {2010}, abstract = {Bead-on-plate butt joints of 2.5 mm hot rolled DP600/DP600 and 1.2 mm cold rolled TRIP700/TRIP700 steel sheets were performed using 6 kW CO2 laser beam welding. The welding speed ranged from 1.5 to 3.0 and from 2.1 to 3.9 m/min in DP/DP and TRIP/TRIP steel weldments respectively. A top surface helium gas was used as a shielding gas at a flow rate of 20 l/min. Metallographic examinations and transverse tensile testing (DIN EN 895: 1995) were carried out to characterize the weldments. The formability of base metals and weldments were investigated by standard Erichsen test (DIN EN ISO 20482). It was found that the uniaxial plastic behavior of both DP600 and TRIP700 base metals was in agreement with Swift and modified Mecking-Kocks models respectively. In a perpendicular tensile test to the weld line, all specimens were fractured at the base metal however the strengths were somewhat higher than those of base metal. There was a significant reduction in formability caused by welding of both DP/DP and TRIP/TRIP steel weldments and the formability has been improved with the increase of the welding speed.}, language = {en} } @article{ReisgenSchleserMokrovetal.2010, author = {Reisgen, Uwe and Schleser, Markus and Mokrov, Oleg and Ahmed, Essam}, title = {Shielding gas influences on laser weldability of tailored blanks of advanced automotive steels}, series = {Applied surface science}, volume = {257}, journal = {Applied surface science}, number = {5}, publisher = {Elsevier}, address = {Amsterdam}, issn = {0169-4332 (E-Journal); 0169-4332 (Print)}, doi = {10.1016/j.apsusc.2010.08.042}, pages = {1401 -- 1406}, year = {2010}, abstract = {The effects of shielding gas types and flow rates on CO2 laser weldability of DP600/TRIP700 steel sheets were studied in this work. The evaluated shielding gases were helium (He), argon (Ar) and different mixtures of He and Ar. Weld penetration, tensile strength and formability (Erichsen test) of laser welds were found to be strongly dependent upon the shielding gas types. The ability of shielding gas in removing plasma plume and thus increasing weld penetration is believed to be closely related to ionization potential and atomic weight which determine the period of plasma formation and disappearance. It was found that the higher helium shielding gas flow rate, the deeper weld penetration and the lower weld width.}, language = {en} } @article{AhmedReisgenSchleseretal.2010, author = {Ahmed, Essam and Reisgen, Uwe and Schleser, Markus and Mokrov, Oleg}, title = {On formability of tailor laser welded blanks of DP/TRIP steel sheets}, series = {Science and technology of welding and joining}, volume = {15}, journal = {Science and technology of welding and joining}, number = {5}, publisher = {Maney}, address = {Leeds}, issn = {1743-2936}, doi = {10.1179/136217110X12731414739754}, pages = {337 -- 342}, year = {2010}, abstract = {This paper aims to evaluate the formability of tailor welded blanks of dual phase (DP600)/transformation induced plasticity (TRIP700) steel sheets. In this work, bead on plate butt joints of 2·5 mm DP600 and 1·2 mm TRIP700 steel sheets were performed using CO2 laser beam welding. Microhardness measurements and transverse tensile testing were carried out to characterise the welds. The formability of base metals and welds were investigated by standard Erichsen test. In a perpendicular tensile test to the weld line, all specimens were fractured at the TRIP base metal, and the strengths were somewhat higher than those of base metal. There was a significant reduction in formability caused by welding of the DP600/TRIP700 steel sheets, and the formability increased with increasing welding speed.}, language = {en} } @article{DiltheySchleserFeldmannetal.2008, author = {Dilthey, Ulrich and Schleser, Markus and Feldmann, Martin and Pak, Daniel and Geßler, Achim}, title = {Investigation of punctiform, plane and hybrid joints of textile-reinforced concrete parts}, series = {Cement and concrete composites}, volume = {Vol. 30}, journal = {Cement and concrete composites}, number = {iss. 2}, issn = {0958-9465}, pages = {82 -- 87}, year = {2008}, language = {en} } @article{FeldmannPakGessleretal.2006, author = {Feldmann, Markus and Pak, Daniel and Geßler, Achim and Dilthey, Ulrich and Schleser, Markus}, title = {Bonded connections for textile reinforced concrete structures}, series = {Cailiao-gongcheng = Journal of materials engineering}, journal = {Cailiao-gongcheng = Journal of materials engineering}, number = {Special iss.}, issn = {1001-4381}, pages = {123 -- 127}, year = {2006}, language = {en} } @article{SchleserWalkLaufferRaupachetal.2006, author = {Schleser, Markus and Walk-Lauffer, Bernd and Raupach, Michael and Dilthey, Ulrich}, title = {Application of polymers for textile-reinforced concrete}, series = {Journal of materials in civil engineering : properties, applications, durability}, volume = {18}, journal = {Journal of materials in civil engineering : properties, applications, durability}, number = {5}, issn = {0899-1561}, pages = {670 -- 676}, year = {2006}, language = {en} } @article{AgrafiotisMavroidisKonstandopoulosetal.2007, author = {Agrafiotis, Christos C. and Mavroidis, Ilias and Konstandopoulos, Athansios G. and Hoffschmidt, Bernhard and Stobbe, Per and Romero, Manuel and Fernandez-Quero, Valerio}, title = {Evaluation of porous silicon carbide monolithic honeycombs as volumetric receivers/collectors of concentrated solar radiation}, series = {Solar energy materials and solar cells}, volume = {Vol. 91}, journal = {Solar energy materials and solar cells}, number = {Iss. 6}, issn = {1879-3398 (E-Journal); 0927-0248 (Print)}, pages = {474 -- 488}, year = {2007}, language = {en} }