@article{KilicRaatschenKoerfgenetal.2017,
  author    = {Kilic, S. A. and Raatschen, Hans-J{\"u}rgen and K{\"o}rfgen, B. and Apaydin, N. M. and Astaneh-Asl, A.},
  title     = {FE Model of the Fatih Sultan Mehmet Suspension Bridge Using Thin Shell Finite Elements},
  series = {Arabian Journal for Science and Engineering},
  volume    = {42},
  journal   = {Arabian Journal for Science and Engineering},
  number    = {3},
  publisher = {Springer Nature},
  issn      = {2191-4281},
  doi       = {10.1007/s13369-016-2316-y},
  pages     = {1103 -- 1116},
  year      = {2017},
  abstract  = {This paper presents the results of an eigenvalue analysis of the Fatih Sultan Mehmet Bridge. A high-resolution finite element model was created directly from the available design documents. All physical properties of the structural components were included in detail, so no calibration to the measured data was necessary. The deck and towers were modeled with shell elements. A nonlinear static analysis was performed before the eigenvalue calculation. The calculated natural frequencies and corresponding mode shapes showed good agreement with the available measured ambient vibration data. The calculation of the effective modal mass showed that nine modes had single contributions higher than 5 \% of the total mass. They were in a frequency range up to 1.2 Hz. The comparison of the results for the torsional modes especially demonstrated the advantage of using thin shell finite elements over the beam modeling approach.},
  language  = {en}
}
@article{LopesLeandroCarvalhoetal.2017,
  author    = {Lopes, Pedro and Leandro, Jorge and Carvalho, Rita F. and Bung, Daniel B.},
  title     = {Alternating skimming flow over a stepped spillway},
  series = {Environmental Fluid Mechanics},
  volume    = {17},
  journal   = {Environmental Fluid Mechanics},
  number    = {2},
  publisher = {Springer},
  address   = {Berlin},
  issn      = {1573-1510},
  doi       = {10.1007/s10652-016-9484-x},
  pages     = {303 -- 322},
  year      = {2017},
  language  = {en}
}
@article{BaeckerKochEibenetal.2017,
  author    = {B{\"a}cker, Matthias and Koch, Claudia and Eiben, Sabine and Geiger, Fania and Eber, Fabian and Gliemann, Hartmut and Poghossian, Arshak and Wege, Christina and Sch{\"o}ning, Michael Josef},
  title     = {Tobacco mosaic virus as enzyme nanocarrier for electrochemical biosensors},
  series = {Sensors and Actuators B: Chemical},
  volume    = {238},
  journal   = {Sensors and Actuators B: Chemical},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0925-4005},
  doi       = {10.1016/j.snb.2016.07.096},
  pages     = {716 -- 722},
  year      = {2017},
  abstract  = {The conjunction of (bio-)chemical recognition elements with nanoscale biological building blocks such as virus particles is considered as a very promising strategy for the creation of biohybrids opening novel opportunities for label-free biosensing. This work presents a new approach for the development of biosensors using tobacco mosaic virus (TMV) nanotubes or coat proteins (CPs) as enzyme nanocarriers. Sensor chips combining an array of Pt electrodes loaded with glucose oxidase (GOD)-modified TMV nanotubes or CP aggregates were used for amperometric detection of glucose as a model system for the first time. The presence of TMV nanotubes or CPs on the sensor surface allows binding of a high amount of precisely positioned enzymes without substantial loss of their activity, and may also ensure accessibility of their active centers for analyte molecules. Specific and efficient immobilization of streptavidin-conjugated GOD ([SA]-GOD) complexes on biotinylated TMV nanotubes or CPs was achieved via bioaffinity binding. These layouts were tested in parallel with glucose sensors with adsorptively immobilized [SA]-GOD, as well as [SA]-GOD crosslinked with glutardialdehyde, and came out to exhibit superior sensor performance. The achieved results underline a great potential of an integration of virus/biomolecule hybrids with electronic transducers for future applications in biosensorics and biochips.},
  language  = {en}
}
@article{HacklAndermahrStaatetal.2017,
  author    = {Hackl, M. and Andermahr, J. and Staat, Manfred and Bremer, I. and Borggrefe, J. and Prescher, A. and M{\"u}ller, L. P. and Wegmann, K.},
  title     = {Suture button reconstruction of the central band of the interosseous membrane in Essex-Lopresti lesions: a comparative biomechanical investigation},
  series = {The Journal of Hand Surgery (European Volume)},
  volume    = {42},
  journal   = {The Journal of Hand Surgery (European Volume)},
  number    = {4},
  publisher = {Sage},
  address   = {London},
  issn      = {2043-6289 (Online)},
  doi       = {10.1177/1753193416665943},
  pages     = {370 -- 376},
  year      = {2017},
  language  = {en}
}
@article{PoghossianWernerBuniatyanetal.2017,
  author    = {Poghossian, Arshak and Werner, Frederik and Buniatyan, V. V. and Wagner, Torsten and Miamoto, K. and Yoshinobu, T. and Sch{\"o}ning, Michael Josef},
  title     = {Towards addressability of light-addressable potentiometric sensors: Shunting effect of non-illuminated region and cross-talk},
  series = {Sensor and Actuators B: Chemical},
  journal   = {Sensor and Actuators B: Chemical},
  number    = {244},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0925-4005},
  doi       = {10.1016/j.snb.2017.01.047},
  pages     = {1071 -- 1079},
  year      = {2017},
  abstract  = {The LAPS (light-addressable potentiometric sensor) platform is one of the most attractive approaches for chemical and biological sensing with many applications ranging from pH and ion/analyte concentration measurements up to cell metabolism detection and chemical imaging. However, although it is generally accepted that LAPS measurements are spatially resolved, the light-addressability feature of LAPS devices has not been discussed in detail so far. In this work, an extended electrical equivalent-circuit model of the LAPS has been presented, which takes into account possible cross-talk effects due to the capacitive coupling of the non-illuminated region. A shunting effect of the non-illuminated area on the measured photocurrent and addressability of LAPS devices has been studied. It has been shown, that the measured photocurrent will be determined not only by the local interfacial potential in the illuminated region but also by possible interfacial potential changes in the non-illuminated region, yielding cross-talk effects. These findings were supported by the experimental investigations of a penicillin-sensitive multi-spot LAPS and a metal-insulator-semiconductor LAPS as model systems.},
  language  = {en}
}
@article{NeuJanserKhatibietal.2017,
  author    = {Neu, Eugen and Janser, Frank and Khatibi, Akbar A. and Orifici, Adrian C.},
  title     = {Fully Automated Operational Modal Analysis using multi-stage clustering},
  series = {Mechanical Systems and Signal Processing},
  volume    = {Vol. 84, Part A},
  journal   = {Mechanical Systems and Signal Processing},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0888-3270},
  doi       = {10.1016/j.ymssp.2016.07.031},
  pages     = {308 -- 323},
  year      = {2017},
  language  = {en}
}
@inproceedings{KesslerBalcGebhardtetal.2017,
  author    = {Kessler, Julia and Balc, Nicolae and Gebhardt, Andreas and Abbas, Karim},
  title     = {Basic research on lattice structures focused on the reliance of the cross sectional area and additional coatings},
  series = {The 4th International Conference on Computing and Solutions in Manufacturing Engineering 2016 - CoSME'16},
  booktitle = {The 4th International Conference on Computing and Solutions in Manufacturing Engineering 2016 - CoSME'16},
  edition   = {Vol. 94},
  doi       = {10.1051/matecconf/20179403008},
  pages     = {7 S.},
  year      = {2017},
  language  = {en}
}
@incollection{Lind2017,
  author    = {Lind, Thorsten Patric},
  title     = {Er{\"o}ffnung des Insolvenzverfahrens. Erfaßtes Verm{\"o}gen und Verfahrensbeteiligte. Insolvenzverwalter, Organe der Gl{\"a}ubiger : \S\S 56-62, 66-72, 74-79},
  series = {Insolvenzrecht : Kommentar / hrsg. von Martin Ahrens; Markus Gehrlein; Andreas Ringstmeier . - 3. Auflage},
  booktitle = {Insolvenzrecht : Kommentar / hrsg. von Martin Ahrens; Markus Gehrlein; Andreas Ringstmeier . - 3. Auflage},
  publisher = {Luchterhand},
  address   = {K{\"o}ln},
  isbn      = {978-3-472-08669-7},
  pages     = {690 - 752; 776 - 797; 802 - 818},
  year      = {2017},
  language  = {de}
}
@article{DammSauerbornFendetal.2017,
  author    = {Damm, Marc Andr{\´e} and Sauerborn, Markus and Fend, Thomas and Herrmann, Ulf},
  title     = {Optimisation of a urea selective catalytic reduction system with a coated ceramic mixing element},
  series = {Journal of ceramic science and technology},
  volume    = {8},
  journal   = {Journal of ceramic science and technology},
  number    = {1},
  publisher = {G{\"o}ller},
  address   = {Baden-Baden},
  isbn      = {2190-9385 (Print)},
  issn      = {2190-9385 (Online)},
  doi       = {10.4416/JCST2016-00056},
  pages     = {19 -- 24},
  year      = {2017},
  language  = {en}
}
@article{FiedlerLaddBitz2017,
  author    = {Fiedler, Thomas M. and Ladd, Mark E. and Bitz, Andreas},
  title     = {SAR Simulations \& Safety},
  series = {NeuroImage},
  journal   = {NeuroImage},
  number    = {Epub ahead of print},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1053-8119},
  doi       = {10.1016/j.neuroimage.2017.03.035},
  year      = {2017},
  language  = {en}
}
@article{NoureddineKraffLaddetal.2017,
  author    = {Noureddine, Yacine and Kraff, Oliver and Ladd, Mark E. and Wrede, Karsten H. and Chen, Bixia and Quick, Harald H. and Schaefers, Gregor and Bitz, Andreas},
  title     = {In vitro and in silico assessment of RF-induced heating around intracranial aneurysm clips at 7 Tesla},
  series = {Magnetic Resonance in Medicine},
  journal   = {Magnetic Resonance in Medicine},
  number    = {Early view},
  publisher = {Wiley},
  address   = {Weinheim},
  issn      = {1522-2594},
  doi       = {10.1002/mrm.26650},
  pages     = {14 Seiten},
  year      = {2017},
  language  = {en}
}
@article{FiedlerLaddBitz2017,
  author    = {Fiedler, Thomas M. and Ladd, Mark E. and Bitz, Andreas},
  title     = {RF safety assessment of a bilateral four-channel transmit/receive 7 Tesla breast coil: SAR versus temperature limits},
  series = {Medical Physics},
  volume    = {44},
  journal   = {Medical Physics},
  number    = {1},
  doi       = {10.1002/mp.12034},
  pages     = {143 -- 157},
  year      = {2017},
  language  = {en}
}
@incollection{Lind2017,
  author    = {Lind, Thorsten Patric},
  title     = {Verwaltung und Verwertung der Insolvenzmasse. Sicherung der Insolvenzmasse, Entscheidung {\"u}ber die Verwertung : \S\S 148-164},
  series = {Insolvenzrecht : Kommentar / hrsg. von Martin Ahrens; Markus Gehrlein; Andreas Ringstmeier . - 3. Auflage},
  booktitle = {Insolvenzrecht : Kommentar / hrsg. von Martin Ahrens; Markus Gehrlein; Andreas Ringstmeier . - 3. Auflage},
  publisher = {Luchterhand},
  address   = {K{\"o}ln},
  isbn      = {978-3-472-08669-7},
  pages     = {1437 -- 1479},
  year      = {2017},
  language  = {de}
}
@inproceedings{SchleupenEngemannBagherietal.2017,
  author    = {Schleupen, Josef and Engemann, Heiko and Bagheri, Mohsen and Kallweit, Stephan and Dahmann, Peter},
  title     = {Developing a climbing maintenance robot for tower and rotor blade service of wind turbines},
  series = {Advances in Robot Design and Intelligent Control : Proceedings of the 25th Conference on Robotics in Alpe-Adria-Danube Region (RAAD16)},
  booktitle = {Advances in Robot Design and Intelligent Control : Proceedings of the 25th Conference on Robotics in Alpe-Adria-Danube Region (RAAD16)},
  publisher = {Springer},
  address   = {Cham},
  isbn      = {978-3-319-49058-8},
  doi       = {10.1007/978-3-319-49058-8_34},
  pages     = {310 -- 319},
  year      = {2017},
  language  = {en}
}
@article{Laack2017,
  author    = {Laack, Walter van},
  title     = {Neurophysiologisch ist das nicht alles zu erkl{\"a}ren : Nahtoderfahrungen aus wissenschaftlicher Sicht},
  series = {Der Allgemeinarzt},
  volume    = {38},
  journal   = {Der Allgemeinarzt},
  number    = {1},
  publisher = {Universimed Deutschland GmbH},
  address   = {Mainz},
  issn      = {0172-7249},
  pages     = {4 -- 7},
  year      = {2017},
  language  = {de}
}
@article{AlexopoulosHoffschmidt2017,
  author    = {Alexopoulos, Spiros and Hoffschmidt, Bernhard},
  title     = {Advances in solar tower technology},
  series = {Wiley interdisciplinary reviews : Energy and Environment : WIREs},
  volume    = {6},
  journal   = {Wiley interdisciplinary reviews : Energy and Environment : WIREs},
  number    = {1},
  publisher = {Wiley},
  address   = {Weinheim},
  issn      = {2041-840X},
  doi       = {10.1002/wene.217},
  pages     = {1 -- 19},
  year      = {2017},
  language  = {en}
}
@article{KatzPoghossianSchoening2017,
  author    = {Katz, Evgeny and Poghossian, Arshak and Sch{\"o}ning, Michael Josef},
  title     = {Enzyme-based logic gates and circuits - analytical applications and interfacing with electronics},
  series = {Analytical and Bioanalytical Chemistry},
  volume    = {409},
  journal   = {Analytical and Bioanalytical Chemistry},
  publisher = {Springer},
  address   = {Berlin},
  issn      = {1618-2650},
  doi       = {10.1007/s00216-016-0079-7},
  pages     = {81 -- 94},
  year      = {2017},
  abstract  = {The paper is an overview of enzyme-based logic gates and their short circuits, with specific examples of Boolean AND and OR gates, and concatenated logic gates composed of multi-step enzyme-biocatalyzed reactions. Noise formation in the biocatalytic reactions and its decrease by adding a "filter" system, converting convex to sigmoid response function, are discussed. Despite the fact that the enzyme-based logic gates are primarily considered as components of future biomolecular computing systems, their biosensing applications are promising for immediate practical use. Analytical use of the enzyme logic systems in biomedical and forensic applications is discussed and exemplified with the logic analysis of biomarkers of various injuries, e.g., liver injury, and with analysis of biomarkers characteristic of different ethnicity found in blood samples on a crime scene. Interfacing of enzyme logic systems with modified electrodes and semiconductor devices is discussed, giving particular attention to the interfaces functionalized with signal-responsive materials. Future perspectives in the design of the biomolecular logic systems and their applications are discussed in the conclusion.},
  language  = {en}
}
@book{Timme2017,
  author    = {Timme, Michael},
  title     = {BGB Crashkurs: der sichere Weg durch die Pr{\"u}fung},
  edition   = {4. Auflage},
  publisher = {C.H. Beck},
  address   = {M{\"u}nchen},
  isbn      = {978-3-406-70586-1},
  pages     = {159 S.},
  year      = {2017},
  language  = {de}
}
@incollection{GeislerPieper2017,
  author    = {Geisler, Simon and Pieper, Martin},
  title     = {Mathematik PLuS als E-Book. Kann ein E-Book zur Ingenieursmathematik alle Lerntypen ansprechen?},
  series = {Das elektronische Schulbuch 2016},
  booktitle = {Das elektronische Schulbuch 2016},
  publisher = {LIT Verlag},
  address   = {Berlin},
  isbn      = {978-3-643-13475-2},
  pages     = {99 -- 111},
  year      = {2017},
  language  = {de}
}
@article{HonarvarfardGamellaChannaveerappaetal.2017,
  author    = {Honarvarfard, Elham and Gamella, Maria and Channaveerappa, Devika and Darie, Costel C. and Poghossian, Arshak and Sch{\"o}ning, Michael Josef and Katz, Evgeny},
  title     = {Electrochemically Stimulated Insulin Release from a Modified Graphene-functionalized Carbon Fiber Electrode},
  series = {Electroanalysis},
  volume    = {29},
  journal   = {Electroanalysis},
  number    = {6},
  publisher = {Wiley-VCH},
  address   = {Weinheim},
  issn      = {1521-4109},
  doi       = {10.1002/elan.201700095},
  pages     = {1543 -- 1553},
  year      = {2017},
  abstract  = {A graphene-functionalized carbon fiber electrode was modified with adsorbed polyethylenimine to introduce amino functionalities and then with trigonelline and 4-carboxyphenylboronic acid covalently bound to the amino groups. The trigonelline species containing quarterized pyridine groups produced positive charge on the electrode surface regardless of the pH value, while the phenylboronic acid species were neutral below pH 8 and negatively charged above pH 9 (note that their pKa=8.4). The total charge on the monolayer-modified electrode was positive at the neutral pH and negative at pH > 9. Note that 4-carboxyphenylboronic acid was attached to the electrode surface in molar excess to trigonelline, thus allowing the negative charge to dominate on the electrode surface at basic pH. Negatively charged fluorescent dye-labeled insulin (insulin-FITC) was loaded on the modified electrode surface at pH 7.0 due to its electrostatic attraction to the positively charged interface. The local pH in close vicinity to the electrode surface was increased to ca. 9-10 due to consumption of H+ ions upon electrochemical reduction of oxygen proceeding at the potential of -1.0 V (vs. Ag/AgCl) applied on the modified electrode. The process resulted in recharging of the electrode surface to the negative value due to the formation of the negative charge on the phenylboronic acid groups, thus resulting in the electrostatic repulsion of insulin-FITC and stimulating its release from the electrode surface. The insulin release was characterized by fluorescence spectroscopy (using the FITC-labeled insulin), by electrochemical measurements on an iridium oxide, IrOx, electrode and by mass spectrometry. The graphene-functionalized carbon fiber electrode demonstrated significant advantages in the signal-stimulated insulin release comparing with the carbon fiber electrode without the graphene species.},
  language  = {en}
}
@article{EnningPfaff2017,
  author    = {Enning, Manfred and Pfaff, Raphael},
  title     = {G{\"u}terwagen 4.0 - Der G{\"u}terwagen f{\"u}r das Internet der Dinge. Teil 1: Gesamtsystembetrachtung und grundlegendes Konzept},
  series = {ETR - Eisenbahntechnische Rundschau},
  volume    = {66},
  journal   = {ETR - Eisenbahntechnische Rundschau},
  number    = {1/2},
  publisher = {DVV Media Group},
  address   = {Hamburg},
  issn      = {0013-2845},
  pages     = {12 -- 16},
  year      = {2017},
  language  = {de}
}
@article{Enning2017,
  author    = {Enning, Manfred},
  title     = {Vom "K{\"o}nig der Landstraße" zur "Ameise 4.0"},
  series = {ETR - Eisenbahntechnische Rundschau},
  volume    = {66},
  journal   = {ETR - Eisenbahntechnische Rundschau},
  number    = {1/2},
  publisher = {DVV Media Group},
  address   = {Hamburg},
  issn      = {0013-2845},
  pages     = {3},
  year      = {2017},
  abstract  = {Auf Eisenbahn- und Logistikkonferenzen werden gelegentlich Videos von Blattschneiderameisen gezeigt, die effizient und selbstorganisiert große Mengen Material durch den Dschungel transportieren. Daran sollen wir uns ein Beispiel nehmen.},
  language  = {de}
}
@incollection{PieperWaehlisch2017,
  author    = {Pieper, Martin and W{\"a}hlisch, Georg},
  title     = {Mehrwert von E-Learning durch f{\"a}cher{\"u}bergreifenden Einsatz},
  series = {Teaching is Touching the Future \& ePS 2016 - Kompetenzorientiertes Lehren, Lernen und Pr{\"u}fen},
  booktitle = {Teaching is Touching the Future \& ePS 2016 - Kompetenzorientiertes Lehren, Lernen und Pr{\"u}fen},
  publisher = {UVW Universit{\"a}tsverlag Webler},
  address   = {Bielefeld},
  isbn      = {978-3-946017-05-9},
  pages     = {193 -- 196},
  year      = {2017},
  language  = {de}
}
@article{LanzlKotliar2017,
  author    = {Lanzl, I. and Kotliar, Konstantin},
  title     = {K{\"o}nnen Anti-VEGF-Injektionen Glaukom oder okul{\"a}re Hypertension verursachen?},
  series = {Klinische Monatsbl{\"a}tter f{\"u}r Augenheilkunde},
  volume    = {234},
  journal   = {Klinische Monatsbl{\"a}tter f{\"u}r Augenheilkunde},
  number    = {2},
  publisher = {Thieme},
  address   = {Stuttgart},
  issn      = {0023-2165},
  doi       = {10.1055/s-0043-101819},
  pages     = {191 -- 193},
  year      = {2017},
  language  = {de}
}
@article{HacklWegmannKahmannetal.2017,
  author    = {Hackl, Michael and Wegmann, Kilian and Kahmann, Stephanie Lucina and Heinze, Nicolai and Staat, Manfred and Neiss, Wolfram F. and Scaal, Martin and M{\"u}ller, Lars P.},
  title     = {Radial shortening osteotomy reduces radiocapitellar contact pressures while preserving valgus stability of the elbow},
  series = {Knee Surgery, Sports Traumatology, Arthroscopy},
  volume    = {25},
  journal   = {Knee Surgery, Sports Traumatology, Arthroscopy},
  number    = {7},
  publisher = {Springer},
  address   = {Berlin},
  issn      = {1433-7347},
  doi       = {10.1007/s00167-017-4468-z},
  pages     = {2280 -- 2288},
  year      = {2017},
  language  = {en}
}
@article{ZangeSchopenAlbrachtetal.2017,
  author    = {Zange, Jochen and Schopen, Kathrin and Albracht, Kirsten and Gerlach, Darius A. and Frings-Meuthen, Petra and Maffiuletti, Nicola A. and Bloch, Wilhelm and Rittweger, J{\"o}rn},
  title     = {Using the Hephaistos orthotic device to study countermeasure effectiveness of neuromuscular electrical stimulation and dietary lupin protein supplementation, a randomised controlled trial},
  series = {Plos one},
  volume    = {12},
  journal   = {Plos one},
  number    = {2},
  doi       = {10.1371/journal.pone.0171562},
  year      = {2017},
  language  = {en}
}
@inproceedings{GranatHoefkenSchuba2017,
  author    = {Granat, Andreas and H{\"o}fken, Hans-Wilhelm and Schuba, Marko},
  title     = {Intrusion Detection of the ICS Protocol EtherCAT},
  pages     = {1 -- 5},
  year      = {2017},
  abstract  = {Control mechanisms like Industrial Controls Systems (ICS) and its subgroup SCADA (Supervisory Control and Data Acquisition) are a prerequisite to automate industrial processes. While protection of ICS on process management level is relatively straightforward - well known office IT security mechanisms can be used - protection on field bus level is harder to achieve as there are real-time and production requirements like 24x7 to consider. One option to improve security on field bus level is to introduce controls that help to detect and to react on attacks. This paper introduces an initial set of intrusion detection mechanisms for the field bus protocol EtherCAT. To this end existing Ethernet attack vectors including packet injection and man-in-the-middle attacks are tested in an EtherCAT environment, where they could interrupt the EtherCAT network and may even cause physical damage. Based on the signatures of such attacks, a preprocessor and new rule options are defined for the open source intrusion detection system Snort demonstrating the general feasibility of intrusion detection on field bus level.},
  language  = {en}
}
@inproceedings{SchreiberKraftZuendorf2017,
  author    = {Schreiber, Marc and Kraft, Bodo and Z{\"u}ndorf, Albert},
  title     = {Metrics Driven Research Collaboration: Focusing on Common Project Goals Continuously},
  series = {39th International Conference on Software Engineering, May 20-28, 2017 - Buenos Aires, Argentina},
  booktitle = {39th International Conference on Software Engineering, May 20-28, 2017 - Buenos Aires, Argentina},
  pages     = {8 Seiten},
  year      = {2017},
  abstract  = {Research collaborations provide opportunities for both practitioners and researchers: practitioners need solutions for difficult business challenges and researchers are looking for hard problems to solve and publish. Nevertheless, research collaborations carry the risk that practitioners focus on quick solutions too much and that researchers tackle theoretical problems, resulting in products which do not fulfill the project requirements. In this paper we introduce an approach extending the ideas of agile and lean software development. It helps practitioners and researchers keep track of their common research collaboration goal: a scientifically enriched software product which fulfills the needs of the practitioner's business model. This approach gives first-class status to application-oriented metrics that measure progress and success of a research collaboration continuously. Those metrics are derived from the collaboration requirements and help to focus on a commonly defined goal. An appropriate tool set evaluates and visualizes those metrics with minimal effort, and all participants will be pushed to focus on their tasks with appropriate effort. Thus project status, challenges and progress are transparent to all research collaboration members at any time.},
  language  = {en}
}
@incollection{DuongNguyenStaat2017,
  author    = {Duong, Minh Tuan and Nguyen, Nhu Huynh and Staat, Manfred},
  title     = {Physical response of hyperelastic models for composite materials and soft tissues},
  series = {Advances in Composite Material},
  booktitle = {Advances in Composite Material},
  publisher = {Scientific Research Publishing},
  address   = {Wuhan},
  isbn      = {978-1-61896-300-0 (Hardcover), 978-1-61896-299-7 (Paperback)},
  pages     = {316},
  year      = {2017},
  language  = {en}
}
@book{RencklyWaehlisch2017,
  author    = {Renckly, Sven and W{\"a}hlisch, Georg},
  title     = {Technisches Zeichnen f{\"u}r Dummies},
  publisher = {Wiley},
  address   = {Weinheim},
  isbn      = {978-3-527-70966-3},
  pages     = {347 Seiten},
  year      = {2017},
  language  = {de}
}
@book{LabischWaehlisch2017,
  author    = {Labisch, Susanna and W{\"a}hlisch, Georg},
  title     = {Technisches Zeichnen: Eigenst{\"a}ndig lernen und effektiv {\"u}ben},
  edition   = {5. Aufl.},
  publisher = {Springer Fachmedien},
  address   = {Wiesbaden},
  isbn      = {978-3-658-18313-4},
  doi       = {10.1007/978-3-658-18313-4},
  pages     = {XI, 300 S. 291 Abb., 50 Abb. in Farbe},
  year      = {2017},
  language  = {de}
}
@inproceedings{SchreiberKraftZuendorf2017,
  author    = {Schreiber, Marc and Kraft, Bodo and Z{\"u}ndorf, Albert},
  title     = {Metrics driven research collaboration: focusing on common project goals continuously},
  series = {Proceedings : 2017 IEEE/ACM 4th International Workshop on Software Engineering Research and Industrial Practice : SER\&IP 2017 : 21 May 2017 Buenos Aires, Argentina},
  booktitle = {Proceedings : 2017 IEEE/ACM 4th International Workshop on Software Engineering Research and Industrial Practice : SER\&IP 2017 : 21 May 2017 Buenos Aires, Argentina},
  editor    = {Bilof, Randall},
  publisher = {IEEE Press},
  address   = {Piscataway, NJ},
  isbn      = {978-1-5386-2797-6},
  doi       = {10.1109/SER-IP.2017..6},
  pages     = {41 -- 47},
  year      = {2017},
  language  = {en}
}
@article{GamellaZakharchenkoGuzetal.2017,
  author    = {Gamella, Maria and Zakharchenko, Andrey and Guz, Nataliia and Masi, Madeline and Minko, Sergiy and Kolpashchikov, Dmitry M. and Iken, Heiko and Poghossian, Arshak and Sch{\"o}ning, Michael Josef and Katz, Evgeny},
  title     = {DNA computing system activated by electrochemically triggered DNA realease from a polymer-brush-modified electrode array},
  series = {Electroanalysis},
  volume    = {29},
  journal   = {Electroanalysis},
  number    = {2},
  publisher = {Wiley-VCH},
  address   = {Weinheim},
  issn      = {1521-4109},
  doi       = {10.1002/elan.201600389},
  pages     = {398 -- 408},
  year      = {2017},
  abstract  = {An array of four independently wired indium tin oxide (ITO) electrodes was used for electrochemically stimulated DNA release and activation of DNA-based Identity, AND and XOR logic gates. Single-stranded DNA molecules were loaded on the mixed poly(N,N-dimethylaminoethyl methacrylate) (PDMAEMA)/poly(methacrylic acid) (PMAA) brush covalently attached to the ITO electrodes. The DNA deposition was performed at pH 5.0 when the polymer brush is positively charged due to protonation of tertiary amino groups in PDMAEMA, thus resulting in electrostatic attraction of the negatively charged DNA. By applying electrolysis at -1.0 V(vs. Ag/AgCl reference) electrochemical oxygen reduction resulted in the consumption of hydrogen ions and local pH increase near the electrode surface. The process resulted in recharging the polymer brush to the negative state due to dissociation of carboxylic groups of PMAA, thus repulsing the negatively charged DNA and releasing it from the electrode surface. The DNA release was performed in various combinations from different electrodes in the array assembly. The released DNA operated as input signals for activation of the Boolean logic gates. The developed system represents a step forward in DNA computing, combining for the first time DNA chemical processes with electronic input signals.},
  language  = {en}
}
@article{SousaSiqueiraVerciketal.2017,
  author    = {Sousa, Marcos A. M. and Siqueira, Jose R. Jr. and Vercik, Andres and Sch{\"o}ning, Michael Josef and Oliveira, Osvaldo N. Jr.},
  title     = {Determining the optimized layer-by-layer film architecture with dendrimer/carbon nanotubes for field-effect sensors},
  series = {IEEE Sensors Journal},
  volume    = {17},
  journal   = {IEEE Sensors Journal},
  number    = {6},
  publisher = {IEEE},
  address   = {New York},
  issn      = {1558-1748},
  doi       = {10.1109/JSEN.2017.2653238},
  pages     = {1735 -- 1740},
  year      = {2017},
  abstract  = {The capacitive electrolyte-insulator-semiconductor (EIS) structure is a typical device based on a field-effect sensor platform. With a simple silicon-based structure, EIS have been useful for several sensing applications, especially with incorporation of nanostructured films to modulate the ionic transport and the flat-band potential. In this paper, we report on ion transport and changes in flat-band potential in EIS sensors made with layer-by-layer films containing poly(amidoamine) (PAMAM) dendrimer and single-walled carbon nanotubes (SWNTs) adsorbed on p-Si/SiO 2 /Ta 2 O 5 chips with an Al ohmic contact. The impedance spectra were fitted using an equivalent circuit model, from which we could determine parameters such as the double-layer capacitance. This capacitance decreased with the number of bilayers owing to space charge accumulated at the electrolyte-insulator interface, up to three PAMAM/SWNTs bilayers, after which it stabilized. The charge-transfer resistance was also minimum for three bilayers, thus indicating that this is the ideal architecture for an optimized EIS performance. The understanding of the influence of nanostructures and the fine control of operation parameters pave the way for optimizing the design and performance of new EIS sensors.},
  language  = {en}
}
@article{YoshinobuMiyamotoWerneretal.2017,
  author    = {Yoshinobu, Tatsuo and Miyamoto, Ko-ichiro and Werner, Frederik and Poghossian, Arshak and Wagner, Torsten and Sch{\"o}ning, Michael Josef},
  title     = {Light-addressable potentiometric sensors for quantitative spatial imaging of chemical species},
  series = {Annual Review of Analytical Chemistry},
  volume    = {10},
  journal   = {Annual Review of Analytical Chemistry},
  publisher = {Annual Reviews},
  address   = {Palo Alto, Calif.},
  issn      = {1936-1327},
  doi       = {10.1146/annurev-anchem-061516-045158},
  pages     = {225 -- 246},
  year      = {2017},
  abstract  = {A light-addressable potentiometric sensor (LAPS) is a semiconductor-based chemical sensor, in which a measurement site on the sensing surface is defined by illumination. This light addressability can be applied to visualize the spatial distribution of pH or the concentration of a specific chemical species, with potential applications in the fields of chemistry, materials science, biology, and medicine. In this review, the features of this chemical imaging sensor technology are compared with those of other technologies. Instrumentation, principles of operation, and various measurement modes of chemical imaging sensor systems are described. The review discusses and summarizes state-of-the-art technologies, especially with regard to the spatial resolution and measurement speed; for example, a high spatial resolution in a submicron range and a readout speed in the range of several tens of thousands of pixels per second have been achieved with the LAPS. The possibility of combining this technology with microfluidic devices and other potential future developments are discussed.},
  language  = {en}
}
@article{SchneiderSchneiderKinderetal.2017,
  author    = {Schneider, Wilhelm and Schneider, Bettina and Kinder, Stephanie and Meinhardt, Kerstin},
  title     = {Grundbegriffe der Abgabenordnung},
  series = {Das Wirtschaftsstudium : wisu ; Zeitschrift f{\"u}r Ausbildung, Examen, Berufseinstieg und Fortbildung},
  volume    = {46},
  journal   = {Das Wirtschaftsstudium : wisu ; Zeitschrift f{\"u}r Ausbildung, Examen, Berufseinstieg und Fortbildung},
  number    = {5},
  publisher = {Lange},
  address   = {D{\"u}sseldorf},
  issn      = {0340-3084},
  pages     = {575 -- 581},
  year      = {2017},
  language  = {de}
}
@book{Schmidt2017,
  author    = {Schmidt, Bernd},
  title     = {Grundlagen der Elektrotechnik und Elektronik f{\"u}r Ingenieure der Schienenfahrzeugtechnik und anderer Fachrichtungen : mit 12 Tabellen und 221 Abbildungen ; NEU mit Verst{\"a}ndnisaufgaben und L{\"o}sungsbeispielen},
  edition   = {2. vollst{\"a}ndig {\"u}berarbeitete Auflage},
  publisher = {B. Schmidt, Fachverlag f{\"u}r Elektro- und Informationstechnik},
  address   = {Bielefeld},
  isbn      = {978-3-944131-03-0},
  pages     = {XXV, 307 Seiten : Illustrationen, Diagramme},
  year      = {2017},
  language  = {de}
}
@article{PfaffEnning2017,
  author    = {Pfaff, Raphael and Enning, Manfred},
  title     = {G{\"u}terwagen 4.0 - Der G{\"u}terwagen f{\"u}r das Internet der Dinge. Teil 2: Ausgew{\"a}hlte technische Aspekte und Prozesse},
  series = {ETR - Eisenbahntechnische Rundschau},
  volume    = {66},
  journal   = {ETR - Eisenbahntechnische Rundschau},
  number    = {5},
  publisher = {DVV Media Group},
  address   = {Hamburg},
  issn      = {0013-2845},
  pages     = {74 -- 77},
  year      = {2017},
  language  = {de}
}
@article{MichaelMayerWeberetal.2017,
  author    = {Michael, Hackl and Mayer, Katharina and Weber, Mareike and Staat, Manfred and van Riet, Roger and Burkhart, Klau Josef and M{\"u}ller, Lars Peter and Wegmann, Kilian},
  title     = {Plate osteosynthesis of proximal ulna fractures : a biomechanical micromotion analysis},
  series = {The journal of hand surgery},
  volume    = {42},
  journal   = {The journal of hand surgery},
  number    = {10},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0363-5023},
  doi       = {10.1016/j.jhsa.2017.05.014},
  pages     = {834.e1 -- 834.e7},
  year      = {2017},
  language  = {en}
}
@inproceedings{AbelPerezVianaCiritsisetal.2017,
  author    = {Abel, Alexander and P{\´e}rez-Viana, Daniel and Ciritsis, Bernard and Staat, Manfred},
  title     = {Prevention of femur neck fractures through femoroplasty},
  series = {2nd YRA MedTech Symposium 2017 : June 8th - 9th / 2017 / Hochschule Ruhr-West},
  booktitle = {2nd YRA MedTech Symposium 2017 : June 8th - 9th / 2017 / Hochschule Ruhr-West},
  editor    = {Erni, Daniel and Fischerauer, Alice and Himmel, J{\"o}rg and Seeger, Thomas and Thelen, Klaus},
  publisher = {Universit{\"a}t Duisburg-Essen},
  address   = {Duisburg},
  organization    = {MedTech Symposium},
  isbn      = {978-3-9814801-9-1},
  doi       = {10.17185/duepublico/43984},
  pages     = {114 -- 115},
  year      = {2017},
  language  = {en}
}
@article{BalzerStreit2017,
  author    = {Balzer, Hermann and Streit, Daniel},
  title     = {Das Translationsrisiko multinationaler Konzerne in Deutschland: Eine explorative Analyse von Verst{\"a}ndnis, Bedeutung und Management-Praxis mit Hilfe der Critical Incident Technique},
  series = {Schmalenbachs Zeitschrift f{\"u}r betriebswirtschaftliche Forschung},
  journal   = {Schmalenbachs Zeitschrift f{\"u}r betriebswirtschaftliche Forschung},
  number    = {Online first},
  publisher = {Springer},
  address   = {Berlin},
  issn      = {2366-6153},
  doi       = {10.1007/s41471-017-0029-x},
  pages     = {1 -- 40},
  year      = {2017},
  language  = {de}
}
@article{ArreolaOberlaenderMaetzkowetal.2017,
  author    = {Arreola, Julio and Oberl{\"a}nder, Jan and M{\"a}tzkow, M. and Keusgen, Michael and Sch{\"o}ning, Michael Josef},
  title     = {Surface functionalization for spore-based biosensors with organosilanes},
  series = {Electrochimica Acta},
  volume    = {241},
  journal   = {Electrochimica Acta},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0013-4686},
  doi       = {10.1016/j.electacta.2017.04.157},
  pages     = {237 -- 243},
  year      = {2017},
  abstract  = {In the present work, surface functionalization of different sensor materials was studied. Organosilanes are well known to serve as coupling agent for biomolecules or cells on inorganic materials. 3-aminopropyltriethoxysilane (APTES) was used to attach microbiological spores time to an interdigitated sensor surface. The functionality and physical properties of APTES were studied on isolated sensor materials, namely silicon dioxide (SiO2) and platinum (Pt) as well as the combined material on sensor level. A predominant immobilization of spores could be demonstrated on SiO2 surfaces. Additionally, the impedance signal of APTES-functionalized biosensor chips has been investigated.},
  language  = {en}
}
@article{BronderPoghossianKeusgenetal.2017,
  author    = {Bronder, Thomas and Poghossian, Arshak and Keusgen, Michael and Sch{\"o}ning, Michael Josef},
  title     = {Label-free detection of double-stranded DNA molecules with polyelectrolyte-modified capacitive field-effect sensors},
  series = {tm - Technisches Messen},
  volume    = {84},
  journal   = {tm - Technisches Messen},
  number    = {10},
  publisher = {De Gruyter},
  address   = {Oldenbourg},
  doi       = {10.1515/teme-2017-0015},
  pages     = {628 -- 634},
  year      = {2017},
  abstract  = {In this study, polyelectrolyte-modified field-effect-based electrolyte-insulator-semiconductor (EIS) devices have been used for the label-free electrical detection of double-stranded deoxyribonucleic acid (dsDNA)molecules. The sensor-chip functionalization with a positively charged polyelectrolyte layer provides the possibility of direct adsorptive binding of negatively charged target DNA oligonucleotides onto theSiO2-chip surface.EIS sensors can be utilized as a tool to detect surface-charge changes; the electrostatic adsorption of oligonucleotides onto the polyelectrolyte layer leads to a measureable surface-potential change. Signals of 39mV have been recorded after the incubation with the oligonucleotide solution. Besides the electrochemical experiments, the successful adsorption of dsDNA onto the polyelectrolyte layer has been verified via fluorescence microscopy. The presented results demonstrate that the signal recording of EISchips, which are modified with a polyelectrolyte layer, canbe used as a favorable approach for a fast, cheap and simple detection method for dsDNA.},
  language  = {en}
}
@inproceedings{SchwankeHoefkenSchuba2017,
  author    = {Schwanke, Peter and H{\"o}fken, Hans-Wilhelm and Schuba, Marko},
  title     = {Security Analysis of the ADS Protocol of a Beckhoff CX2020 PLC},
  pages     = {1 -- 5},
  year      = {2017},
  abstract  = {ICSs (Industrial Control Systems) and its subset SCADA systems (Supervisory Control and Data Acquisition) are getting exposed to a constant stream of new threats. The increasing importance of IT security in ICS requires viable methods to assess the security of ICS, its individual components, and its protocols. This paper presents a security analysis with focus on the communication protocols of a single PLC (Programmable Logic Controller). The PLC, a Beckhoff CX2020, is examined and new vulnerabilities of the system are revealed. Based on these findings recommendations are made to improve security of the Beckhoff system and its protocols.},
  language  = {en}
}
@book{Pieper2017,
  author    = {Pieper, Martin},
  title     = {Mathematische Optimierung: Eine Einf{\"u}hrung in die kontinuierliche Optimierung mit Beispielen},
  publisher = {Springer Fachmedien},
  address   = {Wiesbaden},
  isbn      = {978-3-658-16975-6},
  doi       = {10.1007/978-3-658-16975-6},
  pages     = {IX, 53 S. 20 Abb.},
  year      = {2017},
  language  = {de}
}
@inproceedings{ThurnGebhardt2017,
  author    = {Thurn, Laura and Gebhardt, Andreas},
  title     = {Arousing Enthusiasm for STEM: Teaching 3D Printing Technology},
  series = {Conference Proceedings: New Perspectives in Science Education},
  booktitle = {Conference Proceedings: New Perspectives in Science Education},
  publisher = {liberiauniversitaria.it},
  address   = {Padua},
  isbn      = {978-88-6292-847-2},
  pages     = {87 -- 92},
  year      = {2017},
  language  = {en}
}
@inproceedings{BirgelLeschingerWegmannetal.2017,
  author    = {Birgel, Stefan and Leschinger, Tim and Wegmann, Kilian and Staat, Manfred},
  title     = {Calculation of muscle forces and joint reaction loads in shoulder area via an OpenSim based computer calculation},
  series = {2nd YRA MedTech Symposium 2017 : June 8th - 9th / 2017 / Hochschule Ruhr-West},
  booktitle = {2nd YRA MedTech Symposium 2017 : June 8th - 9th / 2017 / Hochschule Ruhr-West},
  editor    = {Erni, Daniel and Fischerauer, Alice and Himmel, J{\"o}rg and Seeger, Thomas and Thelen, Klaus},
  publisher = {Universit{\"a}t Duisburg-Essen},
  address   = {Duisburg},
  organization    = {MedTech Symposium},
  isbn      = {978-3-9814801-9-1},
  doi       = {10.17185/duepublico/43984},
  pages     = {116 -- 117},
  year      = {2017},
  language  = {en}
}
@inproceedings{JabbariBhattaraiAndingetal.2017,
  author    = {Jabbari, Medisa and Bhattarai, Aroj and Anding, Ralf and Staat, Manfred},
  title     = {Biomechanical simulation of different prosthetic meshes for repairing uterine/vaginal vault prolapse},
  series = {2nd YRA MedTech Symposium 2017 : June 8th - 9th / 2017 / Hochschule Ruhr-West},
  booktitle = {2nd YRA MedTech Symposium 2017 : June 8th - 9th / 2017 / Hochschule Ruhr-West},
  editor    = {Erni, Daniel and Fischerauer, Alice and Himmel, J{\"o}rg and Seeger, Thomas and Thelen, Klaus},
  publisher = {Universit{\"a}t Duisburg-Essen},
  address   = {Duisburg},
  organization    = {MedTech Symposium},
  isbn      = {978-3-9814801-9-1},
  doi       = {10.17185/duepublico/43984},
  pages     = {118 -- 119},
  year      = {2017},
  language  = {en}
}
@inproceedings{SuryoputriGhaderiLinderetal.2017,
  author    = {Suryoputri, Nathania and Ghaderi, Aydin and Linder, Peter and Kotliar, Konstantin and G{\"o}ttler, Jens and Sorg, Christian and Grimmer, Timo},
  title     = {Does hemodynamic response function change in Alzheimer disease?},
  series = {2nd YRA MedTech Symposium 2017 : June 8th - 9th / 2017 / Hochschule Ruhr-West},
  booktitle = {2nd YRA MedTech Symposium 2017 : June 8th - 9th / 2017 / Hochschule Ruhr-West},
  editor    = {Erni, Daniel and Fischerauer, Alice and Himmel, J{\"o}rg and Seeger, Thomas and Thelen, Klaus},
  publisher = {Universit{\"a}t Duisburg-Essen},
  address   = {Duisburg},
  organization    = {MedTech Symposium},
  isbn      = {978-3-9814801-9-1},
  doi       = {10.17185/duepublico/43984},
  pages     = {92},
  year      = {2017},
  language  = {en}
}
@inproceedings{SchneiderAlHakimKayseretal.2017,
  author    = {Schneider, Oliver and Al Hakim, Taher and Kayser, Peter and Digel, Ilya},
  title     = {Development and trials of a test chamber for ultrasound-assisted sampling of living cells from solid surfaces},
  series = {2nd YRA MedTech Symposium 2017 : June 8th - 9th / 2017 / Hochschule Ruhr-West},
  booktitle = {2nd YRA MedTech Symposium 2017 : June 8th - 9th / 2017 / Hochschule Ruhr-West},
  editor    = {Erni, Daniel and Fischerauer, Alice and Himmel, J{\"o}rg and Seeger, Thomas and Thelen, Klaus},
  publisher = {Universit{\"a}t Duisburg-Essen},
  address   = {Duisburg},
  organization    = {MedTech Symposium},
  isbn      = {978-3-9814801-9-1},
  doi       = {10.17185/duepublico/43984},
  pages     = {96 -- 97},
  year      = {2017},
  language  = {en}
}
@inproceedings{SchlemmerPorstBassametal.2017,
  author    = {Schlemmer, Katharina and Porst, Dariusz and Bassam, Rasha and Artmann, Gerhard and Digel, Ilya},
  title     = {Effects of nitric oxide (NO) and ATP on red blood cell phenotype and deformability},
  series = {2nd YRA MedTech Symposium 2017 : June 8th - 9th / 2017 / Hochschule Ruhr-West},
  booktitle = {2nd YRA MedTech Symposium 2017 : June 8th - 9th / 2017 / Hochschule Ruhr-West},
  editor    = {Erni, Daniel and Fischerauer, Alice and Himmel, J{\"o}rg and Seeger, Thomas and Thelen, Klaus},
  publisher = {Universit{\"a}t Duisburg-Essen},
  address   = {Duisburg},
  organization    = {MedTech Symposium},
  isbn      = {978-3-9814801-9-1},
  doi       = {10.17185/duepublico/43984},
  pages     = {100 -- 101},
  year      = {2017},
  language  = {en}
}
@inproceedings{KuhlenDigel2017,
  author    = {Kuhlen, Max and Digel, Ilya},
  title     = {Fluorescence signatures and detection limits of ubiquitous terrestrial bio-compounds},
  series = {2nd YRA MedTech Symposium 2017 : June 8th - 9th / 2017 / Hochschule Ruhr-West},
  booktitle = {2nd YRA MedTech Symposium 2017 : June 8th - 9th / 2017 / Hochschule Ruhr-West},
  editor    = {Erni, Daniel and Fischerauer, Alice and Himmel, J{\"o}rg and Seeger, Thomas and Thelen, Klaus},
  publisher = {Universit{\"a}t Duisburg-Essen},
  address   = {Duisburg},
  organization    = {MedTech Symposium},
  isbn      = {978-3-9814801-9-1},
  doi       = {10.17185/duepublico/43984},
  pages     = {102 -- 103},
  year      = {2017},
  language  = {en}
}
@inproceedings{deHondePorstDigel2017,
  author    = {de Honde, Lukas and Porst, Dariusz and Digel, Ilya},
  title     = {A randomized, observational thermographic study of the neck region before and after a physiotherapeutic intervention},
  series = {2nd YRA MedTech Symposium 2017 : June 8th - 9th / 2017 / Hochschule Ruhr-West},
  booktitle = {2nd YRA MedTech Symposium 2017 : June 8th - 9th / 2017 / Hochschule Ruhr-West},
  editor    = {Fischerauer, Alice},
  publisher = {Universit{\"a}t Duisburg-Essen},
  address   = {Duisburg},
  organization    = {MedTech Symposium},
  isbn      = {978-3-9814801-9-1},
  doi       = {10.17185/duepublico/43984},
  pages     = {122 -- 123},
  year      = {2017},
  language  = {en}
}
@article{HorbachDuongStaat2017,
  author    = {Horbach, Andreas and Duong, Minh Tuan and Staat, Manfred},
  title     = {Modelling of compressible and orthotropic surgical mesh implants based on optical deformation measurement},
  series = {Journal of the mechanical behavior of biomedical materials},
  volume    = {74},
  journal   = {Journal of the mechanical behavior of biomedical materials},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1751-6161},
  doi       = {10.1016/j.jmbbm.2017.06.012},
  pages     = {400 -- 410},
  year      = {2017},
  language  = {en}
}
@inproceedings{OberlaenderArreolaHansenetal.2017,
  author    = {Oberl{\"a}nder, Jan and Arreola, Julio and Hansen, Christina and Greeff, Anton and Mayer, Marlena and Keusgen, Michael and Sch{\"o}ning, Michael Josef},
  title     = {Impedimetric Biosensor to Enable Fast Evaluation of Gaseous Sterilization Processes},
  series = {MDPI Proceedings},
  volume    = {1},
  booktitle = {MDPI Proceedings},
  number    = {4},
  doi       = {10.3390/proceedings1040435},
  pages     = {4 Seiten},
  year      = {2017},
  language  = {en}
}
@inproceedings{MolinnusHardtKaeveretal.2017,
  author    = {Molinnus, Denise and Hardt, Gabriel and K{\"a}ver, Larissa and Willenberg, Holger S. and Poghossian, Arshak and Keusgen, Michael and Sch{\"o}ning, Michael Josef},
  title     = {Detection of Adrenaline Based on Bioelectrocatalytical System to Support Tumor Diagnostic Technology},
  series = {MDPI Proceedings},
  booktitle = {MDPI Proceedings},
  doi       = {10.3390/proceedings1040506},
  pages     = {4 Seiten},
  year      = {2017},
  language  = {en}
}
@article{MuschallikMolinnusBongaertsetal.2017,
  author    = {Muschallik, Lukas and Molinnus, Denise and Bongaerts, Johannes and Pohl, Martina and Wagner, Torsten and Sch{\"o}ning, Michael Josef and Siegert, Petra and Selmer, Thorsten},
  title     = {(R,R)-Butane-2,3-diol Dehydrogenase from Bacillus clausii DSM 8716T: Cloning and Expression of the bdhA-Gene, and Initial Characterization of Enzyme},
  series = {Journal of Biotechnology},
  volume    = {258},
  journal   = {Journal of Biotechnology},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0168-1656},
  doi       = {10.1016/j.jbiotec.2017.07.020},
  pages     = {41 -- 50},
  year      = {2017},
  abstract  = {The gene encoding a putative (R,R)-butane-2,3-diol dehydrogenase (bdhA) from Bacillus clausii DSM 8716T was isolated, sequenced and expressed in Escherichia coli. The amino acid sequence of the encoded protein is only distantly related to previously studied enzymes (identity 33-43\%) and exhibited some uncharted peculiarities. An N-terminally StrepII-tagged enzyme variant was purified and initially characterized. The isolated enzyme catalyzed the (R)-specific oxidation of (R,R)- and meso-butane-2,3-diol to (R)- and (S)-acetoin with specific activities of 12 U/mg and 23 U/mg, respectively. Likewise, racemic acetoin was reduced with a specific activity of up to 115 U/mg yielding a mixture of (R,R)- and meso-butane-2,3-diol, while the enzyme reduced butane-2,3-dione (Vmax 74 U/mg) solely to (R,R)-butane-2,3-diol via (R)-acetoin. For these reactions only activity with the co-substrates NADH/NAD+ was observed. The enzyme accepted a selection of vicinal diketones, α-hydroxy ketones and vicinal diols as alternative substrates. Although the physiological function of the enzyme in B. clausii remains elusive, the data presented herein clearly demonstrates that the encoded enzyme is a genuine (R,R)-butane-2,3-diol dehydrogenase with potential for applications in biocatalysis and sensor development.},
  language  = {en}
}
@article{MoraisGomesSilvaetal.2017,
  author    = {Morais, Paulo V. and Gomes, Vanderley F., Jr. and Silva, Anielle C. A. and Dantas, Noelio O. and Sch{\"o}ning, Michael Josef and Siqueira, Jos{\´e} R., Jr.},
  title     = {Nanofilm of ZnO nanocrystals/carbon nanotubes as biocompatible layer for enzymatic biosensors in capacitive field-effect devices},
  series = {Journal of Materials Science},
  volume    = {52},
  journal   = {Journal of Materials Science},
  number    = {20},
  publisher = {Springer},
  address   = {Berlin},
  issn      = {1573-4803},
  doi       = {10.1007/s10853-017-1369-y},
  pages     = {12314 -- 12325},
  year      = {2017},
  abstract  = {The incorporation of nanomaterials that are biocompatible with different types of biological compounds has allowed the development of a new generation of biosensors applied especially in the biomedical field. In particular, the integration of film-based nanomaterials employed in field-effect devices can be interesting to develop biosensors with enhanced properties. In this paper, we studied the fabrication of sensitive nanofilms combining ZnO nanocrystals and carbon nanotubes (CNTs), prepared by means of the layer-by-layer (LbL) technique, in a capacitive electrolyte-insulator-semiconductor (EIS) structure for detecting glucose and urea. The ZnO nanocrystals were incorporated in a polymeric matrix of poly(allylamine) hydrochloride (PAH), and arranged with multi-walled CNTs in a LbL PAH-ZnO/CNTs film architecture onto EIS chips. The electrochemical characterizations were performed by capacitance-voltage and constant capacitance measurements, while the morphology of the films was characterized by atomic force microscopy. The enzymes glucose oxidase and urease were immobilized on film's surface for detection of glucose and urea, respectively. In order to obtain glucose and urea biosensors with optimized amount of sensitive films, we investigated the ideal number of bilayers for each detection system. The glucose biosensor showed better sensitivity and output signal for an LbL PAH-ZnO/CNTs nanofilm with 10 bilayers. On the other hand, the urea biosensor presented enhanced properties even for the first bilayer, exhibiting high sensitivity and output signal. The presence of the LbL PAH-ZnO/CNTs films led to biosensors with better sensitivity and enhanced response signal, demonstrating that the adequate use of nanostructured films is feasible for proof-of-concept biosensors with improved properties that may be employed for biomedical applications.},
  language  = {en}
}
@article{DantismTakenagaWagneretal.2017,
  author    = {Dantism, Shahriar and Takenaga, Shoko and Wagner, Torsten and Wagner, Patrick and Sch{\"o}ning, Michael Josef},
  title     = {Differential imaging of the metabolism of bacteria and eukaryotic cells based on light-addressable potentiometric sensors},
  series = {Electrochimica Acta},
  volume    = {246},
  journal   = {Electrochimica Acta},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0013-4686},
  doi       = {10.1016/j.electacta.2017.05.196},
  pages     = {234 -- 241},
  year      = {2017},
  abstract  = {A light-addressable potentiometric sensor (LAPS) is a field-effect-based potentiometric sensor with an electrolyte/insulator/semiconductor (EIS) structure, which is able to monitor analyte concentrations of (bio-)chemical species in aqueous solutions in a spatially resolved way. Therefore, it is also an appropriate tool to record 2D-chemical images of concentration variations on the sensor surface. In the present work, two differential, LAPS-based measurement principles are introduced to determine the metabolic activity of Escherichia coli (E. coli) K12 and Chinese hamster ovary (CHO) cells as test microorganisms. Hereby, we focus on i) the determination of the extracellular acidification rate (ΔpH/min) after adding glucose solutions to the cell suspensions; and ii) recording the amplitude increase of the photocurrent (Iph) related to the produced acids from E. coli K12 bacteria and CHO cells on the sensor surface by 2D-chemical imaging. For this purpose, 3D-printed multi-chamber structures were developed and mounted on the planar sensor-chip surface to define four independent compartments, enabling differential measurements with varying cell concentrations. The differential concept allows eliminating unwanted drift effects and, with the four-chamber structures, measurements on the different cell concentrations were performed simultaneously, thus reducing also the overall measuring time.},
  language  = {en}
}
@article{JildehKirchnerOberlaenderetal.2017,
  author    = {Jildeh, Zaid B. and Kirchner, Patrick and Oberl{\"a}nder, Jan and Kremers, Alexander and Wagner, Torsten and Wagner, Patrick H. and Sch{\"o}ning, Michael Josef},
  title     = {FEM-based modeling of a calorimetric gas sensor for hydrogen peroxide monitoring},
  series = {physica status solidi a : applications and materials sciences},
  journal   = {physica status solidi a : applications and materials sciences},
  number    = {Early View},
  publisher = {Wiley-VCH},
  address   = {Weinheim},
  issn      = {1862-6319},
  doi       = {10.1002/pssa.201600912},
  year      = {2017},
  abstract  = {A physically coupled finite element method (FEM) model is developed to study the response behavior of a calorimetric gas sensor. The modeled sensor serves as a monitoring device of the concentration of gaseous hydrogen peroxide (H2 O2) in a high temperature mixture stream in aseptic sterilization processes. The principle of operation of a calorimetric H2 O2 sensor is analyzed and the results of the numerical model have been validated by using previously published sensor experiments. The deviation in the results between the FEM model and experimental data are presented and discussed.},
  language  = {en}
}
@article{MolinnusPoghossianKeusgenetal.2017,
  author    = {Molinnus, Denise and Poghossian, Arshak and Keusgen, Michael and Katz, Evgeny and Sch{\"o}ning, Michael Josef},
  title     = {Coupling of Biomolecular Logic Gates with Electronic Transducers: From Single Enzyme Logic Gates to Sense/Act/Treat Chips},
  series = {Electroanalysis},
  volume    = {29},
  journal   = {Electroanalysis},
  number    = {8},
  publisher = {Wiley},
  address   = {Weinheim},
  issn      = {1521-4109},
  doi       = {10.1002/elan.201700208},
  pages     = {1840 -- 1849},
  year      = {2017},
  abstract  = {The integration of biomolecular logic principles with electronic transducers allows designing novel digital biosensors with direct electrical output, logically triggered drug-release, and closed-loop sense/act/treat systems. This opens new opportunities for advanced personalized medicine in the context of theranostics. In the present work, we will discuss selected examples of recent developments in the field of interfacing enzyme logic gates with electrodes and semiconductor field-effect devices. Special attention is given to an enzyme OR/Reset logic gate based on a capacitive field-effect electrolyte-insulator-semiconductor sensor modified with a multi-enzyme membrane. Further examples are a digital adrenaline biosensor based on an AND logic gate with binary YES/NO output and an integrated closed-loop sense/act/treat system comprising an amperometric glucose sensor, a hydrogel actuator, and an insulin (drug) sensor.},
  language  = {en}
}
@incollection{PoghossianSchoening2017,
  author    = {Poghossian, Arshak and Sch{\"o}ning, Michael Josef},
  title     = {Nanomaterial-Modified Capacitive Field-Effect Biosensors},
  series = {Springer Series on Chemical Sensors and Biosensors (Methods and Applications)},
  booktitle = {Springer Series on Chemical Sensors and Biosensors (Methods and Applications)},
  publisher = {Springer},
  address   = {Berlin, Heidelberg},
  doi       = {10.1007/5346_2017_2},
  pages     = {1 -- 25},
  year      = {2017},
  abstract  = {The coupling of charged molecules, nanoparticles, and more generally, inorganic/organic nanohybrids with semiconductor field-effect devices based on an electrolyte-insulator-semiconductor (EIS) system represents a very promising strategy for the active tuning of electrochemical properties of these devices and, thus, opening new opportunities for label-free biosensing by the intrinsic charge of molecules. The simplest field-effect sensor is a capacitive EIS sensor, which represents a (bio-)chemically sensitive capacitor. In this chapter, selected examples of recent developments in the field of label-free biosensing using nanomaterial-modified capacitive EIS sensors are summarized. In the first part, we present applications of EIS sensors modified with negatively charged gold nanoparticles for the label-free electrostatic detection of positively charged small proteins and macromolecules, for monitoring the layer-by-layer formation of oppositely charged polyelectrolyte (PE) multilayers as well as for the development of an enzyme-based biomolecular logic gate. In the second part, examples of a label-free detection by means of EIS sensors modified with a positively charged weak PE layer are demonstrated. These include electrical detection of on-chip and in-solution hybridized DNA (deoxyribonucleic acid) as well as an EIS sensor with pH-responsive weak PE/enzyme multilayers for enhanced field-effect biosensing.},
  language  = {en}
}
@article{ArreolaKeusgenSchoening2017,
  author    = {Arreola, Julio and Keusgen, Michael and Sch{\"o}ning, Michael Josef},
  title     = {Effect of O2 plasma on properties of electrolyte-insulator-semiconductor structures},
  series = {physica status solidi a : applications and materials sciences},
  volume    = {214},
  journal   = {physica status solidi a : applications and materials sciences},
  publisher = {Wiley-VCH},
  address   = {Weinheim},
  issn      = {1862-6319},
  doi       = {10.1002/pssa.201700025},
  pages     = {Artikel 1700025},
  year      = {2017},
  abstract  = {Prior to immobilization of biomolecules or cells onto biosensor surfaces, the surface must be physically or chemically activated for further functionalization. Organosilanes are a versatile option as they facilitate the immobilization through their terminal groups and also display self-assembly. Incorporating hydroxyl groups is one of the important methods for primary immobilization. This can be done, for example, with oxygen plasma treatment. However, this treatment can affect the performance of the biosensors and this effect is not quite well understood for surface functionalization. In this work, the effect of O2 plasma treatment on EIS sensors was investigated by means of electrochemical characterizations: capacitance-voltage (C-V) and constant capacitance (ConCap) measurements. After O2 plasma treatment, the potential of the EIS sensor dramatically shifts to a more negative value. This was successfully reset by using an annealing process.},
  language  = {en}
}
@article{MiyamotoHayashiSakamotoetal.2017,
  author    = {Miyamoto, Ko-ichiro and Hayashi, Kosuke and Sakamoto, Azuma and Werner, Frederik and Wagner, Torsten and Sch{\"o}ning, Michael Josef and Yoshinobu, Tatsuo},
  title     = {A high-Q resonance-mode measurement of EIS capacitive sensor by elimination of series resistance},
  series = {Sensor and Actuators B: Chemical},
  volume    = {248},
  journal   = {Sensor and Actuators B: Chemical},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0925-4005},
  doi       = {10.1016/j.snb.2017.03.002},
  pages     = {1006 -- 1010},
  year      = {2017},
  abstract  = {An EIS capacitive sensor is a semiconductor-based potentiometric sensor, which is sensitive to the ion concentration or pH value of the solution in contact with the sensing surface. To detect a small change in the ion concentration or pH, a small capacitance change must be detected. Recently, a resonance-mode measurement was proposed, in which an inductor was connected to the EIS capacitive sensor and the resonant frequency was correlated with the pH value. In this study, the Q factor of the resonant circuit was enhanced by canceling the internal resistance of the reference electrode and the internal resistance of the inductor coil with the help of a bypass capacitor and a negative impedance converter, respectively. 1\% variation of the signal in the developed system corresponded to a pH change of 3.93 mpH, which was about 1/12 of the conventional method, suggesting a better performance in detection of a small pH change.},
  language  = {en}
}
@article{WernerMiyamotoWagneretal.2017,
  author    = {Werner, Frederik and Miyamoto, Ko-ichiro and Wagner, Torsten and Sch{\"o}ning, Michael Josef and Yoshinobu, Tatsuo},
  title     = {Lateral resolution enhancement of pulse-driven light-addressable potentiometric sensor},
  series = {Sensor and Actuators B: Chemical},
  volume    = {248},
  journal   = {Sensor and Actuators B: Chemical},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0925-4005},
  doi       = {10.1016/j.snb.2017.02.057},
  pages     = {961 -- 965},
  year      = {2017},
  abstract  = {To study chemical and biological processes, spatially resolved determination of the concentrations of one or more analyte species is of distinct interest. With a light-addressable potentiometric sensor (LAPS), chemical images can be created, which visualize the concentration distribution above the sensor plate. One important challenge is to achieve a good lateral resolution in order to detect events that take place in a small and limited region. LAPS utilizes a focused light spot to address the measurement region. By moving this light spot along the semiconductor sensor plate, the concentration distribution can be observed. In this study, we show that utilizing a pulse as light excitation instead of a traditionally used continuously modulated light excitation, the lateral resolution can be improved by a factor of 6 or more.},
  language  = {en}
}
@article{SchollMoraisGabrieletal.2017,
  author    = {Scholl, Fabio and Morais, Paulo and Gabriel, Rayla and Sch{\"o}ning, Michael Josef and Siqueira, Jose Roberto, Jr. and Caseli, Luciano},
  title     = {Carbon nanotubes arranged as smart interfaces in lipid Langmuir-Blodgett films enhancing the enzymatic properties of penicillinase for biosensing applications},
  series = {Applied Materials \& Interfaces},
  volume    = {9},
  journal   = {Applied Materials \& Interfaces},
  number    = {36},
  publisher = {ACS},
  address   = {Washington},
  issn      = {1944-8252},
  doi       = {10.1021/acsami.7b08095},
  pages     = {31054 -- 31066},
  year      = {2017},
  abstract  = {In this paper, carbon nanotubes (CNTs) were incorporated in penicillinase-phospholipid Langmuir and Langmuir-Blodgett (LB) films to enhance the enzyme catalytic properties. Adsorption of the penicillinase and CNTs at dimyristoylphosphatidic acid (DMPA) monolayers at the air-water interface was investigated by surface pressure-area isotherms, vibrational spectroscopy, and Brewster angle microscopy. The floating monolayers were transferred to solid supports through the LB technique, forming mixed DMPA-CNTs-PEN films, which were investigated by quartz crystal microbalance, vibrational spectroscopy, and atomic force microscopy. Enzyme activity was studied with UV-vis spectroscopy and the feasibility of the supramolecular device nanostructured as ultrathin films were essayed in a capacitive electrolyte-insulator-semiconductor (EIS) sensor device. The presence of CNTs in the enzyme-lipid LB film not only tuned the catalytic activity of penicillinase but also helped conserve its enzyme activity after weeks, showing increased values of activity. Viability as penicillin sensor was demonstrated with capacitance/voltage and constant capacitance measurements, exhibiting regular and distinctive output signals over all concentrations used in this work. These results may be related not only to the nanostructured system provided by the film, but also to the synergism between the compounds on the active layer, leading to a surface morphology that allowed a fast analyte diffusion because of an adequate molecular accommodation, which also preserved the penicillinase activity. This work therefore demonstrates the feasibility of employing LB films composed of lipids, CNTs, and enzymes as EIS devices for biosensing applications.},
  language  = {en}
}
@article{TranMottaghyArltKoerferetal.2017,
  author    = {Tran, Linda and Mottaghy, K. and Arlt-K{\"o}rfer, Sabine and Waluga, Christian and Behbahani, Mehdi},
  title     = {An experimental study of shear-dependent human platelet adhesion and underlying protein-binding mechanisms in a cylindrical Couette system},
  series = {Biomedizinische Technik},
  volume    = {62},
  journal   = {Biomedizinische Technik},
  number    = {4},
  publisher = {De Gruyter},
  address   = {Berlin},
  issn      = {0013-5585},
  doi       = {10.1515/bmt-2015-0034},
  pages     = {383 -- 392},
  year      = {2017},
  language  = {en}
}
@incollection{TranTranMatthiesetal.2017,
  author    = {Tran, N. T. and Tran, Thanh Ngoc and Matthies, M. G. and Stavroulakis, G. E. and Staat, Manfred},
  title     = {Shakedown Analysis Under Stochastic Uncertainty by Chance Constrained Programming},
  series = {Advances in Direct Methods for Materials and Structures},
  booktitle = {Advances in Direct Methods for Materials and Structures},
  publisher = {Springer},
  address   = {Cham},
  isbn      = {978-3-319-59810-9},
  doi       = {10.1007/978-3-319-59810-9_6},
  pages     = {85 -- 103},
  year      = {2017},
  abstract  = {In this paper we propose a stochastic programming method to analyse limit and shakedown of structures under uncertainty condition of strength. Based on the duality theory, the shakedown load multiplier formulated by the kinematic theorem is proved actually to be the dual form of the shakedown load multiplier formulated by static theorem. In this investigation a dual chance constrained programming algorithm is developed to calculate simultaneously both the upper and lower bounds of the plastic collapse limit and the shakedown limit. The edge-based smoothed finite element method (ES-FEM) with three-node linear triangular elements is used for structural analysis.},
  language  = {en}
}
@article{LambersBragard2017,
  author    = {Lambers, Andreas and Bragard, Michael},
  title     = {Kinetische Skulptur - Treffen sich ein E-Techniker und ein K{\"u}nstler ...},
  series = {Elektor : learn, design, share},
  volume    = {48},
  journal   = {Elektor : learn, design, share},
  number    = {9},
  publisher = {Elektor-Verlag},
  address   = {Aachen},
  issn      = {0932-5468},
  pages     = {78 -- 83},
  year      = {2017},
  abstract  = {Die Verbindung der Welten dressierter Elektronen und grenzenloser Kreativit{\"a}t bietet ein großes Potential; zum Beispiel bei modernen Skulpturen, deren Form sich durch Motoren ver{\"a}ndern kann. An der FH Aachen wurde ein solches Projekt verwirklicht: Eine Matrix aus Holzkugeln kann Piktogramme anzeigen, aber auch mathematische Funktionen visualisieren. In diesem Artikel beschreiben wir die clevere Ansteuerung der Motoren.},
  language  = {de}
}
@book{NiethammerFissabre2017,
  author    = {Niethammer, Bernhard and Fissabre, Anke},
  title     = {Die Steiff Spielwarenfabrik in Giengen / Brenz : Ein unbekanntes Meisterwerk der fr{\"u}hen Moderne},
  publisher = {Geym{\"u}ller Verlag f{\"u}r Architektur},
  address   = {Aachen},
  isbn      = {978-3-943164-03-9},
  pages     = {64 S.},
  year      = {2017},
  language  = {de}
}
@article{HonarvarfardGamellaPoghossianetal.2017,
  author    = {Honarvarfard, Elham and Gamella, Maria and Poghossian, Arshak and Sch{\"o}ning, Michael Josef and Katz, Evgeny},
  title     = {An enzyme-based reversible Controlled NOT (CNOT) logic gate operating on a semiconductor transducer},
  series = {Applied Materials Today},
  volume    = {9},
  journal   = {Applied Materials Today},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {2352-9407},
  doi       = {10.1016/j.apmt.2017.08.003},
  pages     = {266 -- 270},
  year      = {2017},
  abstract  = {An enzyme-based biocatalytic system mimicking operation of a logically reversible Controlled NOT (CNOT) gate has been interfaced with semiconductor electronic transducers. Electrolyte-insulator-semiconductor (EIS) structures have been used to transduce chemical changes produced by the enzyme system to an electronically readable capacitive output signal using field-effect features of the EIS device. Two enzymes, urease and esterase, were immobilized on the insulating interface of EIS structure producing local pH changes performing XOR logic operation controlled by various combinations of the input signals represented by urea and ethyl butyrate. Another EIS transducer was functionalized with esterase only, thus performing Identity (ID) logic operation for the ethyl butyrate input. Both semiconductor devices assembled in parallel operated as a logically reversible CNOT gate. The present system, despite its simplicity, demonstrated for the first time logically reversible function of the enzyme system transduced electronically with the semiconductor devices. The biomolecular realization of a CNOT gate interfaced with semiconductors is promising for integration into complex biomolecular networks and future biosensor/biomedical applications.},
  language  = {en}
}
@book{Muehl2017,
  author    = {M{\"u}hl, Thomas},
  title     = {Elektrische Messtechnik : Grundlagen, Messverfahren, Anwendungen},
  edition   = {5., {\"u}berarbeitete und erweiterte Auflage},
  publisher = {Springer Vieweg},
  address   = {Wiesbaden},
  isbn      = {978-3-658-15719-7},
  doi       = {10.1007/978-3-658-15720-3},
  pages     = {XVI, 306 Seiten, Illustrationen},
  year      = {2017},
  language  = {de}
}
@article{Hebel2017,
  author    = {Hebel, Christoph},
  title     = {Erfahrungen mit der RIN und aktuelle Weiterentwicklungen},
  series = {Straßenverkehrstechnik: Organ der Forschungsgesellschaft f{\"u}r Straßen- und Verkehrswesen, der Bundesvereinigung der Straßenbau- und Verkehrsingenieure und der {\"O}sterreichischen Forschungsgesellschaft Straße und Verkehr; Zeitschrift f{\"u}r Verkehrsplanung, Verkehrsmanagement, Verkehrssicherheit, Verkehrstechnik},
  volume    = {61},
  journal   = {Straßenverkehrstechnik: Organ der Forschungsgesellschaft f{\"u}r Straßen- und Verkehrswesen, der Bundesvereinigung der Straßenbau- und Verkehrsingenieure und der {\"O}sterreichischen Forschungsgesellschaft Straße und Verkehr; Zeitschrift f{\"u}r Verkehrsplanung, Verkehrsmanagement, Verkehrssicherheit, Verkehrstechnik},
  number    = {7},
  publisher = {Kirschbaum-Verlag},
  address   = {Bonn},
  issn      = {0039-2219},
  pages     = {443 -- 448},
  year      = {2017},
  language  = {de}
}
@article{RoehlenPilasSchoeningetal.2017,
  author    = {R{\"o}hlen, Desiree and Pilas, Johanna and Sch{\"o}ning, Michael Josef and Selmer, Thorsten},
  title     = {Development of an amperometric biosensor platform for the combined determination of l-Malic, Fumaric, and l-Aspartic acid},
  series = {Applied Biochemistry and Biotechnology},
  volume    = {183},
  journal   = {Applied Biochemistry and Biotechnology},
  publisher = {Springer},
  address   = {Berlin},
  issn      = {1559-0291},
  doi       = {10.1007/s12010-017-2578-1},
  pages     = {566 -- 581},
  year      = {2017},
  abstract  = {Three amperometric biosensors have been developed for the detection of L-malic acid, fumaric acid, and L -aspartic acid, all based on the combination of a malate-specific dehydrogenase (MDH, EC 1.1.1.37) and diaphorase (DIA, EC 1.8.1.4). The stepwise expansion of the malate platform with the enzymes fumarate hydratase (FH, EC 4.2.1.2) and aspartate ammonia-lyase (ASPA, EC 4.3.1.1) resulted in multi-enzyme reaction cascades and, thus, augmentation of the substrate spectrum of the sensors. Electrochemical measurements were carried out in presence of the cofactor β-nicotinamide adenine dinucleotide (NAD+) and the redox mediator hexacyanoferrate (III) (HCFIII). The amperometric detection is mediated by oxidation of hexacyanoferrate (II) (HCFII) at an applied potential of + 0.3 V vs. Ag/AgCl. For each biosensor, optimum working conditions were defined by adjustment of cofactor concentrations, buffer pH, and immobilization procedure. Under these improved conditions, amperometric responses were linear up to 3.0 mM for L-malate and fumarate, respectively, with a corresponding sensitivity of 0.7 μA mM-1 (L-malate biosensor) and 0.4 μA mM-1 (fumarate biosensor). The L-aspartate detection system displayed a linear range of 1.0-10.0 mM with a sensitivity of 0.09 μA mM-1. The sensor characteristics suggest that the developed platform provides a promising method for the detection and differentiation of the three substrates.},
  language  = {en}
}
@article{PilasYaziciSelmeretal.2017,
  author    = {Pilas, Johanna and Yazici, Yasemen and Selmer, Thorsten and Keusgen, Michael and Sch{\"o}ning, Michael Josef},
  title     = {Optimization of an amperometric biosensor array for simultaneous measurement of ethanol, formate, d- and l-lactate},
  series = {Electrochimica Acta},
  volume    = {251},
  journal   = {Electrochimica Acta},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0013-4686},
  doi       = {10.1016/j.electacta.2017.07.119},
  pages     = {256 -- 262},
  year      = {2017},
  abstract  = {The immobilization of NAD+-dependent dehydrogenases, in combination with a diaphorase, enables the facile development of multiparametric sensing devices. In this work, an amperometric biosensor array for simultaneous determination of ethanol, formate, d- and l-lactate is presented. Enzyme immobilization on platinum thin-film electrodes was realized by chemical cross-linking with glutaraldehyde. The optimization of the sensor performance was investigated with regard to enzyme loading, glutaraldehyde concentration, pH, cofactor concentration and temperature. Under optimal working conditions (potassium phosphate buffer with pH 7.5, 2.5 mmol L-1 NAD+, 2.0 mmol L-1 ferricyanide, 25 °C and 0.4\% glutaraldehyde) the linear working range and sensitivity of the four sensor elements was improved. Simultaneous and cross-talk free measurements of four different metabolic parameters were performed successfully. The reliable analytical performance of the biosensor array was demonstrated by application in a clarified sample of inoculum sludge. Thereby, a promising approach for on-site monitoring of fermentation processes is provided.},
  language  = {en}
}
@article{AlbannaLuekeSjapicetal.2017,
  author    = {Albanna, Walid and Lueke, Jan Niklas and Sjapic, Volha and Kotliar, Konstantin and Hescheler, J{\"u}rgen and Clusmann, Hans and Sjapic, Sergej and Alpdogan, Serdan and Schneider, Toni and Schubert, Gerrit Alexander and Neumaier, Felix},
  title     = {Electroretinographic Assessment of Inner Retinal Signaling in the Isolated and Superfused Murine Retina},
  series = {Current Eye Research},
  journal   = {Current Eye Research},
  number    = {Article in press},
  publisher = {Taylor \& Francis},
  address   = {London},
  issn      = {1460-2202},
  doi       = {10.1080/02713683.2017.1339807},
  pages     = {1 -- 9},
  year      = {2017},
  language  = {en}
}
@article{SeifarthGrosseGrossmannetal.2017,
  author    = {Seifarth, Volker and Grosse, Joachim O. and Grossmann, Matthias and Janke, Heinz Peter and Arndt, Patrick and Koch, Sabine and Epple, Matthias and Artmann, Gerhard and Temiz Artmann, Ayseg{\"u}l},
  title     = {Mechanical induction of bi-directional orientation of primary porcine bladder smooth muscle cells in tubular fibrin-poly(vinylidene fluoride) scaffolds for ureteral and urethral repair using cyclic and focal balloon catheter stimulation},
  series = {Journal of Biomaterials Applications},
  volume    = {32},
  journal   = {Journal of Biomaterials Applications},
  number    = {3},
  publisher = {Sage},
  address   = {London},
  issn      = {1530-8022},
  doi       = {10.1177/0885328217723178},
  pages     = {321 -- 330},
  year      = {2017},
  language  = {en}
}
@inproceedings{BreuerGuthmannSchoeningetal.2017,
  author    = {Breuer, Lars and Guthmann, Eric and Sch{\"o}ning, Michael Josef and Thoelen, Ronald and Wagner, Torsten},
  title     = {Light-Stimulated Hydrogels with Incorporated Graphene Oxide as Actuator Material for Flow Control in Microfluidic Applications},
  series = {Proceedings Eurosensors 2017 Conference, Paris, France, 3-6 September 2017},
  booktitle = {Proceedings Eurosensors 2017 Conference, Paris, France, 3-6 September 2017},
  doi       = {10.3390/proceedings1040524},
  pages     = {1 -- 4},
  year      = {2017},
  language  = {en}
}
@article{Hoettges2017,
  author    = {H{\"o}ttges, J{\"o}rg},
  title     = {QKan - Management of drainage system data with QGIS},
  series = {Free and Open Source Software for Geospatial (FOSS4G) Conference Proceedings},
  volume    = {17},
  journal   = {Free and Open Source Software for Geospatial (FOSS4G) Conference Proceedings},
  number    = {Article 13},
  pages     = {95 -- 100},
  year      = {2017},
  language  = {en}
}
@article{SrivastavaChaharSharmaetal.2017,
  author    = {Srivastava, A. and Chahar, V. and Sharma, V. and Sun, Y. and Bol, R. and Knolle, F. and Schnug, E. and Hoyler, Friedrich and Naskar, N. and Lahiri, S. and Patnaik, R.},
  title     = {Study of uranium toxicity using low-background gamma-ray spectrometry},
  series = {Journal of Radioanalytical and Nuclear Chemistry},
  journal   = {Journal of Radioanalytical and Nuclear Chemistry},
  number    = {Online first},
  publisher = {Springer},
  address   = {Berlin},
  issn      = {1588-2780},
  doi       = {10.1007/s10967-017-5466-9},
  pages     = {1 -- 7},
  year      = {2017},
  language  = {en}
}
@misc{HacklWegmannKahmannetal.2017,
  author    = {Hackl, Michael and Wegmann, Kilian and Kahmann, Stephanie Lucina and Heinze, Nicolai and Staat, Manfred and Neiss, Wolfram F. and Scaal, Martin and M{\"u}ller, Lars P.},
  title     = {Reply to the letter to the editor: shortening osteotomy of the proximal radius},
  series = {Knee Surgery, Sports Traumatology, Arthroscopy},
  volume    = {25},
  journal   = {Knee Surgery, Sports Traumatology, Arthroscopy},
  number    = {10},
  doi       = {10.1007/s00167-017-4666-8},
  pages     = {3328 -- 3329},
  year      = {2017},
  language  = {en}
}
@misc{NobisrathZuendorfGeorgeetal.2017,
  author    = {Nobisrath, Ulrich and Z{\"u}ndorf, Albert and George, Tobias and Ruben, Jubeh and Kraft, Bodo},
  title     = {Software Stories Guide},
  pages     = {21},
  year      = {2017},
  abstract  = {Software Stories are a simple graphical notation for requirements analysis and design in agile software projects. Software Stories are based on example scenarios. Example scenarios facilitate the communication between lay people or domain experts and software experts.},
  language  = {en}
}
@inproceedings{JablonskiKochBronderetal.2017,
  author    = {Jablonski, Melanie and Koch, Claudia and Bronder, Thomas and Poghossian, Arshak and Wege, Christina and Sch{\"o}ning, Michael Josef},
  title     = {Field-Effect Biosensors Modified with Tobacco Mosaic Virus Nanotubes as Enzyme Nanocarrier},
  series = {MDPI Proceeding},
  volume    = {1},
  booktitle = {MDPI Proceeding},
  number    = {4},
  doi       = {10.3390/proceedings1040505},
  pages     = {4},
  year      = {2017},
  language  = {en}
}
@inproceedings{MiyamotoSutoWerneretal.2017,
  author    = {Miyamoto, Ko-ichiro and Suto, Takeyuki and Werner, Frederik and Wagner, Torsten and Sch{\"o}ning, Michael Josef and Yoshinobu, Tatsuo},
  title     = {Restraining the Diffusion of Photocarriers to Improve the Spatial Resolution of the Chemical Imaging Sensor},
  series = {MDPI Proceedings},
  volume    = {1},
  booktitle = {MDPI Proceedings},
  number    = {4},
  doi       = {10.3390/proceedings1040477},
  pages     = {4 Seiten},
  year      = {2017},
  language  = {en}
}
@article{RietschPfaffenrotBitzetal.2017,
  author    = {Rietsch, Stefan H. G. and Pfaffenrot, Viktor and Bitz, Andreas and Orzada, Stephan and Brunheim, Sascha and Lazik-Palm, Andrea and Theysohn, Jens M. and Ladd, Mark E. and Quick, Harald H. and Kraff, Oliver},
  title     = {An 8-channel transceiver 7-channel receive RF coil setup for high SNR ultrahigh-field MRI of the shoulder at 7T},
  series = {Medical Physics},
  journal   = {Medical Physics},
  number    = {Article in press},
  publisher = {Wiley},
  address   = {Hoboken},
  issn      = {0094-2405},
  doi       = {10.1002/mp.12612},
  year      = {2017},
  language  = {en}
}
@article{KotliarHauserOrtneretal.2017,
  author    = {Kotliar, Konstantin and Hauser, Christine and Ortner, Marion and Muggenthaler, Claudia and Diehl-Schmid, Janine and Angermann, Susanne and Hapfelmeier, Alexander and Schmaderer, Christoph and Grimmer, Timo},
  title     = {Altered neurovascular coupling as measured by optical imaging: a biomarker for Alzheimer's disease},
  series = {Scientific Reports},
  volume    = {7},
  journal   = {Scientific Reports},
  number    = {1},
  publisher = {Springer Nature},
  address   = {Cham},
  issn      = {2045-2322},
  doi       = {10.1038/s41598-017-13349-5},
  pages     = {1 -- 11},
  year      = {2017},
  language  = {en}
}
@article{BreuerMangSchoeningetal.2017,
  author    = {Breuer, Lars and Mang, Thomas and Sch{\"o}ning, Michael Josef and Thoelen, Ronald and Wagner, Torsten},
  title     = {Investigation of the spatial resolution of a laser-based stimulation process for light-addressable hydrogels with incorporated graphene oxide by means of IR thermography},
  series = {Sensors and Actuators A: Physical},
  volume    = {268},
  journal   = {Sensors and Actuators A: Physical},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0924-4247},
  doi       = {10.1016/j.sna.2017.11.031},
  pages     = {126 -- 132},
  year      = {2017},
  language  = {en}
}
@inproceedings{EndressBragard2017,
  author    = {Endress, Tim and Bragard, Michael},
  title     = {Recording of efficiency-maps of low-power electric drive systems using a flexible matlab-based test bench},
  series = {2017 IEEE 58th International Scientific Conference on Power and Electrical Engineering of Riga Technical University (RTUCON)},
  booktitle = {2017 IEEE 58th International Scientific Conference on Power and Electrical Engineering of Riga Technical University (RTUCON)},
  publisher = {IEEE},
  address   = {New York},
  isbn      = {978-1-5386-3846-0},
  doi       = {10.1109/RTUCON.2017.8124775},
  pages     = {5 Seiten},
  year      = {2017},
  abstract  = {This paper introduces a hardware setup to measure efficiency maps of low-power electric motors and their associated inverters. Here, the power of the device under test (DUT) ranges from some Watts to a few hundred Watts. The torque and speed of the DUT are measured independent of voltage and current in multiple load points. A Matlab-based software approach in combination with an open Texas-Instruments (TI) hardware setup ensures flexibility. Exemplarily, the efficiency field of a Permanent Magnet Synchronous Machine (PMSM) is measured to proof the concept. Brushless-DC (BLDC) motors can be tested as well. The nomenclature in this paper is based on the new European standard DIN EN 50598. Special attention is paid to the calculation of the measurement error.},
  language  = {en}
}
@phdthesis{Mainz2017,
  author    = {Mainz, Stefan},
  title     = {Zur Berechnung der Tragf{\"a}higkeit von d{\"u}nnwandigen Koppelpfetten aus Kaltprofilen f{\"u}r Biegung um die schwache Achse und Torsion},
  address   = {Hamburg},
  url       = {http://nbn-resolving.de/urn:nbn:de:gbv:1373-opus-3798},
  pages     = {261 Seiten},
  year      = {2017},
  language  = {de}
}
@article{DemmerChowdhurySelmeretal.2017,
  author    = {Demmer, Julius K. and Chowdhury, Nilanjan Pal and Selmer, Thorsten and Ermler, Ulrich and Buckel, Wolfgang},
  title     = {The semiquinone swing in the bifurcating electron transferring flavoprotein/butyryl-CoA dehydrogenase complex from Clostridium difficile},
  series = {Nature Communications},
  volume    = {8},
  journal   = {Nature Communications},
  number    = {1},
  issn      = {2041-1723},
  doi       = {10.1038/s41467-017-01746-3},
  pages     = {1 -- 10},
  year      = {2017},
  language  = {en}
}
@article{WerkhausenAlbrachtCroninetal.2017,
  author    = {Werkhausen, Amelie and Albracht, Kirsten and Cronin, Neil J. and Meier, Rahel and Mojsen-Moeller, Jens and Seynnes, Olivier R.},
  title     = {Modulation of muscle-tendon interaction in the human triceps surae during an energy dissipation task},
  series = {Journal of Experimental Biology},
  volume    = {220},
  journal   = {Journal of Experimental Biology},
  number    = {22},
  issn      = {0022-0949},
  doi       = {10.1242/jeb.164111},
  pages     = {4141 -- 4149},
  year      = {2017},
  language  = {en}
}
@inproceedings{NiemuellerNeumannHenkeetal.2017,
  author    = {Niemueller, Tim and Neumann, Tobias and Henke, Christoph and Sch{\"o}nitz, Sebastian and Reuter, Sebastian and Ferrein, Alexander and Jeschke, Sabina and Lakemeyer, Gerhard},
  title     = {Improvements for a robust production in the RoboCup logistics league 2016},
  series = {RoboCup 2016: Robot World Cup XX. RoboCup 2016.},
  booktitle = {RoboCup 2016: Robot World Cup XX. RoboCup 2016.},
  publisher = {Springer},
  address   = {Cham},
  isbn      = {978-3-319-68792-6},
  doi       = {10.1007/978-3-319-68792-6_49},
  pages     = {589 -- 600},
  year      = {2017},
  language  = {en}
}
@article{GaribaldiBegingCaneseetal.2017,
  author    = {Garibaldi, F. and Beging, Stefan and Canese, R. and Carpinelli, G. and Clinthorne, N. and Colilli, S. and Cosentino, L. and Finocchiaro, P. and Giuliani, F. and Gricia, M. and Lucentini, M. and Majewski, S. and Monno, E. and Musico, P. and Santavenere, F. and T{\"o}dter, J. and Wegener, Hans-Peter and Ziemons, Karl},
  title     = {A novel TOF-PET MRI detector for diagnosis and follow up of the prostate cancer},
  series = {European Physical Journal Plus},
  volume    = {132},
  journal   = {European Physical Journal Plus},
  number    = {9},
  publisher = {Springer},
  address   = {Berlin},
  issn      = {2190-5444},
  doi       = {10.1140/epjp/i2017-11662-x},
  year      = {2017},
  language  = {en}
}
@article{OrzadaBitzJohstetal.2017,
  author    = {Orzada, Stephan and Bitz, Andreas and Johst, S{\"o}ren and Gratz, Marcel and V{\"o}lker, Maximilian N. and Kraff, Oliver and Abuelhaija, Ashraf and Fiedler, Thomas M. and Solbach, Klaus and Quick, Harald H. and Ladd, Mark E.},
  title     = {Analysis of an integrated 8-Channel Tx/Rx body array for use as a body coil in 7-Tesla MRI},
  series = {Frontiers in Physics},
  volume    = {5},
  journal   = {Frontiers in Physics},
  number    = {Jun},
  issn      = {2296-424X},
  doi       = {10.3389/fphy.2017.00017},
  year      = {2017},
  language  = {en}
}
@article{BalzerStreitHeinze2017,
  author    = {Balzer, Hermann and Streit, Daniel and Heinze, Marcel},
  title     = {Implikationen der Digitalisierung f{\"u}r den Finanzbereich der Unternehmung und das Rollenbild des CFO},
  series = {Betriebswirtschaftliche Implikationen der digitalen Transformation. ZfbF - Schmalenbachs Zeitschrift f{\"u}r betriebswirtschaftliche Forschung, Sonderheft 72},
  journal   = {Betriebswirtschaftliche Implikationen der digitalen Transformation. ZfbF - Schmalenbachs Zeitschrift f{\"u}r betriebswirtschaftliche Forschung, Sonderheft 72},
  number    = {72},
  editor    = {Krause, Stefan},
  publisher = {Springer},
  address   = {Berlin},
  doi       = {10.1007/978-3-658-18751-4_14},
  pages     = {267 -- 283},
  year      = {2017},
  language  = {de}
}
@inproceedings{FunkeBeckmannKeinzetal.2017,
  author    = {Funke, Harald and Beckmann, Nils and Keinz, Jan and Abanteriba, Sylvester},
  title     = {Numerical and Experimental Evaluation of a Dual-Fuel Dry-Low-NOx Micromix Combustor for Industrial Gas Turbine Applications},
  series = {Proceedings of the ASME Turbo Expo 2017: Turbomachinery Technical Conference and Exposition. Volume 4B: Combustion, Fuels and Emissions. Charlotte, North Carolina, USA. June 26-30, 2017},
  booktitle = {Proceedings of the ASME Turbo Expo 2017: Turbomachinery Technical Conference and Exposition. Volume 4B: Combustion, Fuels and Emissions. Charlotte, North Carolina, USA. June 26-30, 2017},
  publisher = {ASME},
  address   = {New York},
  isbn      = {978-0-7918-5085-5},
  doi       = {10.1115/GT2017-64795},
  year      = {2017},
  abstract  = {The Dry-Low-NOx (DLN) Micromix combustion technology has been developed originally as a low emission alternative for industrial gas turbine combustors fueled with hydrogen. Currently the ongoing research process targets flexible fuel operation with hydrogen and syngas fuel. The non-premixed combustion process features jet-in-crossflow-mixing of fuel and oxidizer and combustion through multiple miniaturized flames. The miniaturization of the flames leads to a significant reduction of NOx emissions due to the very short residence time of reactants in the flame. The paper presents the results of a numerical and experimental combustor test campaign. It is conducted as part of an integration study for a dual-fuel (H2 and H2/CO 90/10 Vol.\%) Micromix combustion chamber prototype for application under full scale, pressurized gas turbine conditions in the auxiliary power unit Honeywell Garrett GTCP 36-300. In the presented experimental studies, the integration-optimized dual-fuel Micromix combustor geometry is tested at atmospheric pressure over a range of gas turbine operating conditions with hydrogen and syngas fuel. The experimental investigations are supported by numerical combustion and flow simulations. For validation, the results of experimental exhaust gas analyses are applied. Despite the significantly differing fuel characteristics between pure hydrogen and hydrogen-rich syngas the evaluated dual-fuel Micromix prototype shows a significant low NOx performance and high combustion efficiency. The combustor features an increased energy density that benefits manufacturing complexity and costs.},
  language  = {en}
}
@book{SchneiderSchneider2017,
  author    = {Schneider, Bettina and Schneider, Wilhelm},
  title     = {Abschluss und Abschlussanalyse: systematische Darstellung in {\"U}bersichten},
  edition   = {6. Auflage, Studienausgabe},
  publisher = {Cuvillier},
  address   = {G{\"o}ttingen},
  isbn      = {978-3-7369-9642-7},
  pages     = {Getr. Z{\"a}hlung},
  year      = {2017},
  language  = {de}
}
@article{NiemuellerKarrasFerrein2017,
  author    = {Niemueller, Tim and Karras, Ulrich and Ferrein, Alexander},
  title     = {Meisterschaft der Maschinen: Die Industrial Logistic Liga},
  series = {C´t Magazin f{\"u}r Computertechnik},
  journal   = {C´t Magazin f{\"u}r Computertechnik},
  number    = {26},
  year      = {2017},
  language  = {de}
}
@incollection{NiemuellerZwillingLakemeyeretal.2017,
  author    = {Niemueller, Tim and Zwilling, Frederik and Lakemeyer, Gerhard and L{\"o}bach, Matthias and Reuter, Sebastian and Jeschke, Sabina and Ferrein, Alexander},
  title     = {Cyber-Physical System Intelligence},
  series = {Industrial Internet of Things},
  booktitle = {Industrial Internet of Things},
  publisher = {Springer},
  address   = {Cham},
  isbn      = {978-3-319-42559-7},
  doi       = {10.1007/978-3-319-42559-7_17},
  pages     = {447 -- 472},
  year      = {2017},
  abstract  = {Cyber-physical systems are ever more common in manufacturing industries. Increasing their autonomy has been declared an explicit goal, for example, as part of the Industry 4.0 vision. To achieve this system intelligence, principled and software-driven methods are required to analyze sensing data, make goal-directed decisions, and eventually execute and monitor chosen tasks. In this chapter, we present a number of knowledge-based approaches to these problems and case studies with in-depth evaluation results of several different implementations for groups of autonomous mobile robots performing in-house logistics in a smart factory. We focus on knowledge-based systems because besides providing expressive languages and capable reasoning techniques, they also allow for explaining how a particular sequence of actions came about, for example, in the case of a failure.},
  language  = {en}
}
@inproceedings{StopforthDavrajhFerrein2017,
  author    = {Stopforth, Riaan and Davrajh, Shaniel and Ferrein, Alexander},
  title     = {South African robotics entity for a collaboration initiative},
  series = {Pattern Recognition Association of South Africa and Robotics and Mechatronics International Conference (PRASA-RobMech), 2016},
  booktitle = {Pattern Recognition Association of South Africa and Robotics and Mechatronics International Conference (PRASA-RobMech), 2016},
  publisher = {IEEE},
  isbn      = {978-1-5090-3335-5},
  doi       = {10.1109/RoboMech.2016.7813144},
  pages     = {1 -- 6},
  year      = {2017},
  language  = {en}
}