@inproceedings{StarkBartelDitscheetal.2023, author = {Stark, Ralf and Bartel, Sebastian and Ditsche, Florian and Esch, Thomas}, title = {Design study of a 30kN LOX/LCH4 aerospike rocket engine for lunar lander application}, series = {Aerospace Europe Conference 2023 - 10th EUCASS - 9th CEAS}, booktitle = {Aerospace Europe Conference 2023 - 10th EUCASS - 9th CEAS}, pages = {9 Seiten}, year = {2023}, abstract = {Based on lunar lander concept EL3, various LOX/CH4 aerospike engines were studied. A distinction was made between single and cluster configurations as well as ideal and non-ideal contour concepts. It could be shown that non-ideal aerospike engines promise a significant payload gain.}, language = {en} } @inproceedings{StarkRiepingEsch2023, author = {Stark, Ralf and Rieping, Carla and Esch, Thomas}, title = {The impact of guide tubes on flow separation in rocket nozzles}, series = {Aerospace Europe Conference 2023 - 10th EUCASS - 9th CEAS}, booktitle = {Aerospace Europe Conference 2023 - 10th EUCASS - 9th CEAS}, pages = {8 Seiten}, year = {2023}, abstract = {Rocket engine test facilities and launch pads are typically equipped with a guide tube. Its purpose is to ensure the controlled and safe routing of the hot exhaust gases. In addition, the guide tube induces a suction that effects the nozzle flow, namely the flow separation during transient start-up and shut-down of the engine. A cold flow subscale nozzle in combination with a set of guide tubes was studied experimentally to determine the main influencing parameters.}, language = {en} } @article{SchopenNarayanBeckmannetal.2024, author = {Schopen, Oliver and Narayan, Sriram and Beckmann, Marvin and Najmi, Aezid-Ul-Hassan and Esch, Thomas and Shabani, Bahman}, title = {An EIS approach to quantify the effects of inlet air relative humidity on the performance of proton exchange membrane fuel cells: a pathway to developing a novel fault diagnostic method}, series = {International Journal of Hydrogen Energy}, volume = {58}, journal = {International Journal of Hydrogen Energy}, number = {8}, publisher = {Elsevier}, address = {Amsterdam}, isbn = {0360-3199 (print)}, issn = {1879-3487 (online)}, doi = {10.1016/j.ijhydene.2024.01.218}, pages = {1302 -- 1315}, year = {2024}, abstract = {In this work, the effect of low air relative humidity on the operation of a polymer electrolyte membrane fuel cell is investigated. An innovative method through performing in situ electrochemical impedance spectroscopy is utilised to quantify the effect of inlet air relative humidity at the cathode side on internal ionic resistances and output voltage of the fuel cell. In addition, algorithms are developed to analyse the electrochemical characteristics of the fuel cell. For the specific fuel cell stack used in this study, the membrane resistance drops by over 39 \% and the cathode side charge transfer resistance decreases by 23 \% after increasing the humidity from 30 \% to 85 \%, while the results of static operation also show an increase of ∼2.2 \% in the voltage output after increasing the relative humidity from 30 \% to 85 \%. In dynamic operation, visible drying effects occur at < 50 \% relative humidity, whereby the increase of the air side stoichiometry increases the drying effects. Furthermore, other parameters, such as hydrogen humidification, internal stack structure, and operating parameters like stoichiometry, pressure, and temperature affect the overall water balance. Therefore, the optimal humidification range must be determined by considering all these parameters to maximise the fuel cell performance and durability. The results of this study are used to develop a health management system to ensure sufficient humidification by continuously monitoring the fuel cell polarisation data and electrochemical impedance spectroscopy indicators.}, language = {en} } @misc{MachadoDahmannKeimeretal.2020, author = {Machado, Patricia Almeida and Dahmann, Peter and Keimer, Jona and Saretzki, Charlotte and St{\"u}bing, Felix and K{\"u}pper, Thomas}, title = {Stress profile and individual workload monitoring in general aviation pilots - an experiment's setting}, series = {23. Annual Meeting of the German Society of Travel Medicine, Coburg, 18.-19.9.2020}, journal = {23. Annual Meeting of the German Society of Travel Medicine, Coburg, 18.-19.9.2020}, doi = {10.55225/hppa.156}, year = {2020}, language = {en} } @inproceedings{LangohrBungCrookston2022, author = {Langohr, Philipp and Bung, Daniel Bernhard and Crookston, Brian M.}, title = {Hybrid investigation of labyrinth weirs: Discharge capacity and energy dissipation}, series = {Proceedings of the 39th IAHR World Congress}, booktitle = {Proceedings of the 39th IAHR World Congress}, editor = {Ortega-S{\´a}nchez, Miguel}, publisher = {International Association for Hydro-Environment Engineering and Research (IAHR)}, address = {Madrid}, isbn = {978-90-832612-1-8}, issn = {2521-7119 (print)}, doi = {10.3850/IAHR-39WC252171192022738}, pages = {2313 -- 2318}, year = {2022}, abstract = {The replacement of existing spillway crests or gates with labyrinth weirs is a proven techno-economical means to increase the discharge capacity when rehabilitating existing structures. However, additional information is needed regarding energy dissipation of such weirs, since due to the folded weir crest, a three-dimensional flow field is generated, yielding more complex overflow and energy dissipation processes. In this study, CFD simulations of labyrinth weirs were conducted 1) to analyze the discharge coefficients for different discharges to compare the Cd values to literature data and 2) to analyze and improve energy dissipation downstream of the structure. All tests were performed for a structure at laboratory scale with a height of approx. P = 30.5 cm, a ratio of the total crest length to the total width of 4.7, a sidewall angle of 10° and a quarter-round weir crest shape. Tested headwater ratios were 0.089 ≤ HT/P ≤ 0.817. For numerical simulations, FLOW-3D Hydro was employed, solving the RANS equations with use of finite-volume method and RNG k-ε turbulence closure. In terms of discharge capacity, results were compared to data from physical model tests performed at the Utah Water Research Laboratory (Utah State University), emphasizing higher discharge coefficients from CFD than from the physical model. For upstream heads, some discrepancy in the range of ± 1 cm between literature, CFD and physical model tests was identified with a discussion regarding differences included in the manuscript. For downstream energy dissipation, variable tailwater depths were considered to analyze the formation and sweep-out of a hydraulic jump. It was found that even for high discharges, relatively low downstream Froude numbers were obtained due to high energy dissipation involved by the three-dimensional flow between the sidewalls. The effects of some additional energy dissipation devices, e.g. baffle blocks or end sills, were also analyzed. End sills were found to be non-effective. However, baffle blocks with different locations may improve energy dissipation downstream of labyrinth weirs.}, language = {en} } @inproceedings{CrookstonBung2022, author = {Crookston, Brian M. and Bung, Daniel Bernhard}, title = {Application of RGB-D cameras in hydraulic laboratory studies}, series = {Proceedings of the 39th IAHR World Congress}, booktitle = {Proceedings of the 39th IAHR World Congress}, editor = {Ortega-S{\´a}nchez, Miguel}, publisher = {International Association for Hydro-Environment Engineering and Research (IAHR)}, address = {Madrid}, isbn = {978-90-832612-1-8}, issn = {2521-7119 (print)}, doi = {10.3850/IAHR-39WC252171192022964}, pages = {5127 -- 5133}, year = {2022}, abstract = {Non-intrusive measuring techniques have attained a lot of interest in relation to both hydraulic modeling and prototype applications. Complimenting acoustic techniques, significant progress has been made for the development of new optical methods. Computer vision techniques can help to extract new information, e. g. high-resolution velocity and depth data, from videos captured with relatively inexpensive, consumer-grade cameras. Depth cameras are sensors providing information on the distance between the camera and observed features. Currently, sensors with different working principles are available. Stereoscopic systems reference physical image features (passive system) from two perspectives; in order to enhance the number of features and improve the results, a sensor may also estimate the disparity from a detected light to its original projection (active stereo system). In the current study, the RGB-D camera Intel RealSense D435, working on such stereo vision principle, is used in different, typical hydraulic modeling applications. All tests have been conducted at the Utah Water Research Laboratory. This paper will demonstrate the performance and limitations of the RGB-D sensor, installed as a single camera and as camera arrays, applied to 1) detect the free surface for highly turbulent, aerated hydraulic jumps, for free-falling jets and for an energy dissipation basin downstream of a labyrinth weir and 2) to monitor local scours upstream and downstream of a Piano Key Weir. It is intended to share the authors' experiences with respect to camera settings, calibration, lightning conditions and other requirements in order to promote this useful, easily accessible device. Results will be compared to data from classical instrumentation and the literature. It will be shown that even in difficult application, e. g. the detection of a highly turbulent, fluctuating free-surface, the RGB-D sensor may yield similar accuracy as classical, intrusive probes.}, language = {en} } @inproceedings{HuelsenMulsowDabrowskietal.2023, author = {H{\"u}lsen, Benjamin and Mulsow, Niklas A. and Dabrowski, Adam and Brinkmann, Wiebke and G{\"u}tzlaff, Joel and Spies, Leon and Czupalla, Markus and Kirchner, Frank}, title = {Towards an autonomous micro rover with night survivability for lunar exploration}, series = {Proceedings of the 74th International Astronautical Congress}, booktitle = {Proceedings of the 74th International Astronautical Congress}, publisher = {dfki}, pages = {12 Seiten}, year = {2023}, abstract = {In Europe, efforts are underway to develop key technologies that can be used to explore the Moon and to exploit the resources available. This includes technologies for in-situ resource utilization (ISRU), facilitating the possibility of a future Moon Village. The Moon is the next step for humans and robots to exploit the use of available resources for longer term missions, but also for further exploration of the solar system. A challenge for effective exploration missions is to achieve a compact and lightweight robot to reduce launch costs and open up the possibility of secondary payload options. Current micro rover concepts are primarily designed to last for one day of solar illumination and show a low level of autonomy. Extending the lifetime of the system by enabling survival of the lunar night and implementing a high level of autonomy will significantly increase potential mission applications and the operational range. As a reference mission, the deployment of a micro rover in the equatorial region of the Moon is being considered. An overview of mission parameters and a detailed example mission sequence is given in this paper. The mission parameters are based on an in-depth study of current space agency roadmaps, scientific goals, and upcoming flight opportunities. Furthermore, concepts of the ongoing international micro rover developments are analyzed along with technology solutions identified for survival of lunar nights and a high system autonomy. The results provide a basis of a concise requirements set-up to allow dedicated system developments and qualification measures in the future.}, language = {en} } @inproceedings{MulsowHuelsenGuetzlaffetal.2023, author = {Mulsow, Niklas A. and H{\"u}lsen, Benjamin and G{\"u}tzlaff, Joel and Spies, Leon and Bresser, Andreas and Dabrowski, Adam and Czupalla, Markus and Kirchner, Frank}, title = {Concept and design of an autonomous micro rover for long term lunar exploration}, series = {Proceedings of the 74th International Astronautical Congress}, booktitle = {Proceedings of the 74th International Astronautical Congress}, publisher = {dfki}, address = {Saarbr{\"u}cken}, pages = {13 Seiten}, year = {2023}, abstract = {Research on robotic lunar exploration has seen a broad revival, especially since the Google Lunar X-Prize increasingly brought private endeavors into play. This development is supported by national agencies with the aim of enabling long-term lunar infrastructure for in-situ operations and the establishment of a moon village. One challenge for effective exploration missions is developing a compact and lightweight robotic rover to reduce launch costs and open the possibility for secondary payload options. Existing micro rovers for exploration missions are clearly limited by their design for one day of sunlight and their low level of autonomy. For expanding the potential mission applications and range of use, an extension of lifetime could be reached by surviving the lunar night and providing a higher level of autonomy. To address this objective, the paper presents a system design concept for a lightweight micro rover with long-term mission duration capabilities, derived from a multi-day lunar mission scenario at equatorial regions. Technical solution approaches are described, analyzed, and evaluated, with emphasis put on the harmonization of hardware selection due to a strictly limited budget in dimensions and power.}, language = {en} } @unpublished{SchmuellingGuetzlaffCzupalla2024, author = {Schm{\"u}lling, Max and G{\"u}tzlaff, Joel and Czupalla, Markus}, title = {A thermal simulation environment for moving objects on the lunar surface}, doi = {10.21203/rs.3.rs-3902363/v1}, pages = {12 Seiten}, year = {2024}, abstract = {This paper presents a thermal simulation environment for moving objects on the lunar surface. The goal of the thermal simulation environment is to enable the reliable prediction of the temperature development of a given object on the lunar surface by providing the respective heat fluxes for a mission on a given travel path. The user can import any object geometry and freely define the path that the object should travel. Using the path of the object, the relevant lunar surface geometry is imported from a digital elevation model. The relevant parts of the lunar surface are determined based on distance to the defined path. A thermal model of these surface sections is generated, consisting of a porous layer on top and a denser layer below. The object is moved across the lunar surface, and its inclination is adapted depending on the slope of the terrain below it. Finally, a transient thermal analysis of the object and its environment is performed at several positions on its path and the results are visualized. The paper introduces details on the thermal modeling of the lunar surface, as well as its verification. Furthermore, the structure of the created software is presented. The robustness of the environment is verified with the help of sensitivity studies and possible improvements are presented.}, language = {en} } @inproceedings{KohlbergerWildKasperetal.2021, author = {Kohlberger, David-Sharif and Wild, Dominik and Kasper, Stefan and Czupalla, Markus}, title = {Modeling and analyses of a thermal passively stabilized LEO/GEO star tracker with embedded phase change material applying the Infused Thermal Solutions (ITS) method}, series = {ICES202: Satellite, Payload, and Instrument Thermal Control}, booktitle = {ICES202: Satellite, Payload, and Instrument Thermal Control}, publisher = {Texas Tech University}, address = {Lubbock, Tex.}, pages = {12 Seiten}, year = {2021}, abstract = {Phase change materials offer a way of storing excess heat and releasing it when it is needed. They can be utilized as a method to control thermal behavior without the need for additional energy. This work focuses on exploring the potential of using phase change materials to passively control the thermal behavior of a star tracker by infusing it with a fitting phase change material. Based on the numerical model of the star trackers thermal behavior using ESATAN-TMS without implemented phase change material, a fitting phase change material for selected orbits is chosen and implemented in the thermal model. The altered thermal behavior of the numerical model after the implementation is analyzed for different amounts of the chosen phase change materials using an ESATAN-based subroutine developed by the FH Aachen. The PCM-modelling-subroutine is explained in the paper ICES-2021-110. The results show that an increasing amount of phase change material increasingly damps temperature oscillations. Using an integral part structure some of the mass increase can be compensated.}, language = {en} } @inproceedings{WildCzupallaFoerstner2021, author = {Wild, Dominik and Czupalla, Markus and F{\"o}rstner, Roger}, title = {Modeling, prediction and test of additive manufactured integral structures with embedded lattice and phase change material applying Infused Thermal Solutions (ITS)}, series = {ICES104: Advances in Thermal Control Technology}, booktitle = {ICES104: Advances in Thermal Control Technology}, publisher = {Texas Tech University}, address = {Lubbock, Tex.}, pages = {12 Seiten}, year = {2021}, abstract = {Infused Thermal Solutions (ITS) introduces a method for passive thermal control to stabilize structural components thermally without active heating and cooling systems, but with phase change material (PCM) for thermal energy storage (TES), in combination with lattice - both embedded in additive manufactured functional structures. In this ITS follow-on paper a thermal model approach and associated predictions are presented, related on the ITS functional breadboards developed at FH Aachen. Predictive TES by PCM is provided by a specially developed ITS PCM subroutine, which is applicable in ESATAN. The subroutine is based on the latent heat storage (LHS) method to numerically embed thermo-physical PCM behavior. Furthermore, a modeling approach is introduced to numerically consider the virtual PCM/lattice nodes within the macro-encapsulated PCM voids of the double wall ITS design. Related on these virtual nodes, in-plane and out-of-plane conductive links are defined. The recent additive manufactured ITS breadboard series are thermally cycled in the thermal vacuum chamber, both with and without embedded PCM. Related on breadboard hardware tests, measurement results are compared with predictions and are subsequently correlated. The results of specific simulations and measurements are presented. Recent predictive results of star tracker analyses are also presented in ICES-2021-106, based on this ITS PCM subroutine.}, language = {en} } @article{SchopenShahEschetal.2024, author = {Schopen, Oliver and Shah, Neel and Esch, Thomas and Shabani, Bahman}, title = {Critical quantitative evaluation of integrated health management methods for fuel cell applications}, series = {International Journal of Hydrogen Energy}, volume = {70}, journal = {International Journal of Hydrogen Energy}, publisher = {Elsevier}, address = {Amsterdam}, issn = {0360-3199}, doi = {10.1016/j.ijhydene.2024.05.156}, pages = {370 -- 388}, year = {2024}, abstract = {Online fault diagnostics is a crucial consideration for fuel cell systems, particularly in mobile applications, to limit downtime and degradation, and to increase lifetime. Guided by a critical literature review, in this paper an overview of Health management systems classified in a scheme is presented, introducing commonly utilised methods to diagnose FCs in various applications. In this novel scheme, various Health management system methods are summarised and structured to provide an overview of existing systems including their associated tools. These systems are classified into four categories mainly focused on model-based and non-model-based systems. The individual methods are critically discussed when used individually or combined aimed at further understanding their functionality and suitability in different applications. Additionally, a tool is introduced to evaluate methods from each category based on the scheme presented. This tool applies the technique of matrix evaluation utilising several key parameters to identify the most appropriate methods for a given application. Based on this evaluation, the most suitable methods for each specific application are combined to build an integrated Health management system.}, language = {en} } @article{Czupalla2017, author = {Czupalla, Markus}, title = {Ein Garten im Weltraum}, series = {Spektrum der Wissenschaft}, journal = {Spektrum der Wissenschaft}, publisher = {Spektrum-der-Wiss.-Verl.-Ges.}, address = {Heidelberg}, year = {2017}, language = {de} } @misc{EcclestonDrummondMiddletonetal.2020, author = {Eccleston, Paul and Drummond, Rachel and Middleton, Kevin and Bishop, Georgia and Caldwell, Andrew and Desjonqueres, Lucile and Tosh, Ian and Cann, Nick and Crook, Martin and Hills, Matthew and Pearson, Chris and Simpson, Caroline and Stamper, Richard and Tinetti, Giovanna and Pascale, Enzo and Swain, Mark and Holmes, Warren A. and Wong, Andre and Puig, Ludovic and Pilbratt, G{\"o}ran and Linder, Martin and Boudin, Nathalie and Ertel, Hanno and Gambicorti, Lisa and Halain, Jean-Philippe and Pace, Emanuele and Vilardell, Francesc and G{\´o}mez, Jos{\´e} M. and Colom{\´e}, Josep and Amiaux, J{\´e}r{\^o}me and Cara, Christophe and Berthe, Michel and Moreau, Vincent and Morgante, Gianluca and Malaguti, Giuseppe and Alonso, Gustavo and {\´A}lvarez, Javier P. and Ollivier, Marc and Philippon, Anne and Hellin, Marie-Laure and Roose, Steve and Frericks, Martin and Krijger, Matthijs and Rataj, Miroslaw and Wawer, Piotr and Skup, Konrad and Sobiecki, Mateusz and Christian Jessen, Niels and M{\o}ller Pedersen, S{\o}ren and Hargrave, Peter and Griffin, Matt and Ottensamer, Roland and Hunt, Thomas and Rust, Duncan and Saleh, Aymen and Winter, Berend and Focardi, Mauro and Da Deppo, Vania and Zuppella, Paola and Czupalla, Markus}, title = {The ARIEL payload: A technical overview}, series = {Space Telescopes and Instrumentation 2020: Optical, Infrared, and Millimeter Wave}, volume = {11443}, journal = {Space Telescopes and Instrumentation 2020: Optical, Infrared, and Millimeter Wave}, editor = {Lystrup, Makenzie and Perrin, Marshall D. and Batalha, Natalie and Siegler, Nicholas and Tong, Edward C.}, publisher = {SPIE}, address = {Washington}, doi = {10.1117/12.2561478}, pages = {114430Z}, year = {2020}, abstract = {The Atmospheric Remote-Sensing Infrared Exoplanet Large-survey, ARIEL, has been selected to be the next (M4) medium class space mission in the ESA Cosmic Vision programme. From launch in 2028, and during the following 4 years of operation, ARIEL will perform precise spectroscopy of the atmospheres of ~1000 known transiting exoplanets using its metre-class telescope. A three-band photometer and three spectrometers cover the 0.5 µm to 7.8 µm region of the electromagnetic spectrum. This paper gives an overview of the mission payload, including the telescope assembly, the FGS (Fine Guidance System) - which provides both pointing information to the spacecraft and scientific photometry and low-resolution spectrometer data, the ARIEL InfraRed Spectrometer (AIRS), and other payload infrastructure such as the warm electronics, structures and cryogenic cooling systems.}, language = {en} } @misc{ReiswichBrandtCzupalla2019, author = {Reiswich, Martin and Brandt, Hannes and Czupalla, Markus}, title = {Passive thermal control by integration of phase change material into additively manufactured structures}, series = {E2. 47th Student conference}, journal = {E2. 47th Student conference}, year = {2019}, abstract = {Optical Instruments require an extremely stable thermal surrounding to prevent loss of data quality by misalignments of the instrument components resulting from material deformation due to temperature f luctuations (e.g. from solar intrusion). Phase Change Material (PCM) can be applied as a thermal damper to achieve a more uniform temperature distribution. The challenge of this method is, among others, the integration of PCM into affected areas. If correctly designed, incoming heat is latently absorbed during phase change of the PCM, i.e. the temperature of a structure remains almost constant. In a cold phase, the heat during phase change is released again latently until the PCM returns to its original state of aggregation. Thus, the structure is thermally stabilized. At FH Aachen- University of Applied Sciences research is conducted to apply PCM directly into the structures of affected components (baffles, optical benches, electronic boxes, etc.). Through the application of Additive Manufacturing, the necessary voids are directly printed into these structures and filled later with PCM. Additive Manufacturing enables complex structures that would not have been possible with conservative manufacturing methods. A corresponding Breadboard was developed and manufactured by Selective Laser Melting (SLM). The current state of research includes the handling and analysis of the Breadboard, tests and a correlation of the thermal model. The results have shown analytically and practically that it is possible to use PCM as an integral part of the structure as a thermal damper. The results serve as a basis for the further development of the technology, which should maximize performance and enable the integration of PCM into much more complex structures.}, language = {en} } @misc{GamgamiCzupallaGarciaetal.2016, author = {Gamgami, Farid and Czupalla, Markus and Garcia, Antonio and Agnolon, David}, title = {From planetary transits to spacecraft design: achieving PLATO's pointing performance}, series = {A7. Symposium on technological Requirement for future space astronomy and solar-system science missions}, journal = {A7. Symposium on technological Requirement for future space astronomy and solar-system science missions}, year = {2016}, abstract = {In the last decades, several hundred exoplanets could be detected thanks to space-based observatories, namely CNES' COROT and NASA's Kepler. To expand this quest ESA plans to launch CHEOPS as the f irst small class mission in the cosmic visions program (S1) and PLATO as the 3rd medium class mission, so called M3 . PLATO's primary objective is the detection of Earth like Exoplanets orbiting solar type stars in the habitable zone and characterisation of their bulk properties. This is possible by precise lightcurve measurement via 34 cameras. That said it becomes obvious that accurate pointing is key to achieve the required signal to noise ratio for positive transit detection. The paper will start with a comprehensive overview of PLATO's mission objectives and mission architecture. Hereafter, special focus will be devoted to PLATO's pointing requirements. Understanding the very nature of PLATO's pointing requirements is essential to derive a design baseline to achieve the required performance. The PLATO frequency domain is of particular interest, ranging from 40 mHz to 3 Hz. Due to the very different time-scales involved, the spectral pointing requirement is decomposed into a high frequency part dominated by the attitude control system and the low frequency part dominated by the thermo-elastic properties of the spacecraft's configuration. Both pose stringent constraints on the overall design as well as technology properties to comply with the derived requirements and thus assure a successful mission.}, language = {en} } @inproceedings{BungLangohrWaldenberger2023, author = {Bung, Daniel Bernhard and Langohr, Phillip and Waldenberger, Lisa}, title = {Influence of cycle number in CFD studies of labyrinth weirs}, series = {Proceedings of the 40th IAHR World Congress (Vienna, 2023)}, booktitle = {Proceedings of the 40th IAHR World Congress (Vienna, 2023)}, editor = {Habersack, Helmut and Tritthart, Michael}, publisher = {International Association for Hydro-Environment Engineering and Research (IAHR)}, address = {Madrid}, isbn = {978-90-833476-1-5}, issn = {L 2521-7119 (online)}, doi = {10.3850/978-90-833476-1-5_iahr40wc-p0531-cd}, year = {2023}, abstract = {The major advantage of labyrinth weirs over linear weirs is hydraulic efficiency. In hydraulic modeling efforts, this strength contrasts with limited pump capacity as well as limited computational power for CFD simulations. For the latter, reducing the number of investigated cycles can significantly reduce necessary computational time. In this study, a labyrinth weir with different cycle numbers was investigated. The simulations were conducted in FLOW-3D HYDRO as a Large Eddy Simulation. With a mean deviation of 1.75 \% between simulated discharge coefficients and literature design equations, a reasonable agreement was found. For downstream conditions, overall consistent results were observed as well. However, the orientation of labyrinth weirs with a single cycle should be chosen carefully under consideration of the individual research purpose.}, language = {en} } @article{DroopChenRadfordetal.2023, author = {Droop, Philipp and Chen, Shaohuang and Radford, Melissa J. and Paulßen, Elisabeth and Gates, Byron D. and Reilly, Raymond M. and Radchenko, Valery and Hoehr, Cornelia}, title = {Synthesis of 197m/gHg labelled gold nanoparticles for targeted radionuclide therapy}, series = {Radiochimica Acta}, volume = {111}, journal = {Radiochimica Acta}, number = {10}, publisher = {De Gruyter}, address = {Berlin [u.a.]}, issn = {2193-3405}, doi = {10.1515/ract-2023-0144}, pages = {773 -- 779}, year = {2023}, abstract = {Meitner-Auger-electron emitters have a promising potential for targeted radionuclide therapy of cancer because of their short range and the high linear energy transfer of Meitner-Auger-electrons (MAE). One promising MAE candidate is 197m/gHg with its half-life of 23.8 h and 64.1 h, respectively, and high MAE yield. Gold nanoparticles (AuNPs) that are labelled with 197m/gHg could be a helpful tool for radiation treatment of glioblastoma multiforme when infused into the surgical cavity after resection to prevent recurrence. To produce such AuNPs, 197m/gHg was embedded into pristine AuNPs. Two different syntheses were tested starting from irradiated gold containing trace amounts of 197m/gHg. When sodium citrate was used as reducing agent, no 197m/gHg labelled AuNPs were formed, but with tannic acid, 197m/gHg labeled AuNPs were produced. The method was optimized by neutralizing the pH (pH = 7) of the Au/197m/gHg solution, which led to labelled AuNPs with a size of 12.3 ± 2.0 nm as measured by transmission electron microscopy. The labelled AuNPs had a concentration of 50 μg (gold)/mL with an activity of 151 ± 93 kBq/mL (197gHg, time corrected to the end of bombardment).}, language = {en} } @article{MuesgenanntKoersMcNeilRadchenkoetal.2023, author = {Mues genannt Koers, Lucas and McNeil, S. W. and Radchenko, V. and Paulßen, Elisabeth and Hoehr, Cornelia}, title = {Production of Co-58m in a siphon-style liquid target on a medical cyclotron}, volume = {195}, number = {Art. 110734}, publisher = {Elsevier}, address = {Amsterdam}, issn = {0969-8043}, doi = {10.1016/j.apradiso.2023.110734}, year = {2023}, abstract = {We present the production of 58mCo on a small, 13 MeV medical cyclotron utilizing a siphon style liquid target system. Different concentrated iron(III)-nitrate solutions of natural isotopic distribution were irradiated at varying initial pressures and subsequently separated by solid phase extraction chromatography. The radio cobalt (58m/gCo and 56Co) was successfully produced with saturation activities of (0.35 ± 0.03) MBq μA-1 for 58mCo with a separation recovery of (75 ± 2) \% of cobalt after one separation step utilizing LN-resin.}, language = {en} } @article{MuesgenanntKoersPrevostPaulssenetal.2023, author = {Mues genannt Koers, Lucas and Prevost, David and Paulßen, Elisabeth and Hoehr, Cornelia}, title = {Density reduction effects on the production of [11C]CO2 in Nb-body targets on a medical cyclotron}, volume = {199}, number = {Art. 110911}, publisher = {Elsevier}, address = {Amsterdam}, doi = {10.1016/j.apradiso.2023.110911}, year = {2023}, abstract = {Medical isotope production of 11C is commonly performed in gaseous targets. The power deposition of the proton beam during the irradiation decreases the target density due to thermodynamic mixing and can cause an increase of penetration depth and divergence of the proton beam. In order to investigate the difference how the target-body length influences the operation conditions and the production yield, a 12 cm and a 22 cm Nb-target body containing N2/O2 gas were irradiated using a 13 MeV proton cyclotron. It was found that the density reduction has a large influence on the pressure rise during irradiation and the achievable radioactive yield. The saturation activity of [11C]CO2 for the long target (0.083 Ci/μA) is about 10\% higher than in the short target geometry (0.075 Ci/μA).}, language = {en} } @phdthesis{Bung2023, author = {Bung, Daniel Bernhard}, title = {Imaging techniques for investigation of free-surface flows in hydraulic laboratories}, doi = {10.25926/BUW/0-172}, pages = {XXIII, 218 Seiten}, year = {2023}, abstract = {This thesis aims at the presentation and discussion of well-accepted and new imaging techniques applied to different types of flow in common hydraulic engineering environments. All studies are conducted in laboratory conditions and focus on flow depth and velocity measurements. Investigated flows cover a wide range of complexity, e.g. propagation of waves, dam-break flows, slightly and fully aerated spillway flows as well as highly turbulent hydraulic jumps. Newimagingmethods are compared to different types of sensorswhich are frequently employed in contemporary laboratory studies. This classical instrumentation as well as the general concept of hydraulic modeling is introduced to give an overview on experimental methods. Flow depths are commonly measured by means of ultrasonic sensors, also known as acoustic displacement sensors. These sensors may provide accurate data with high sample rates in case of simple flow conditions, e.g. low-turbulent clear water flows. However, with increasing turbulence, higher uncertainty must be considered. Moreover, ultrasonic sensors can provide point data only, while the relatively large acoustic beam footprint may lead to another source of uncertainty in case of relatively short, highly turbulent surface fluctuations (ripples) or free-surface air-water flows. Analysis of turbulent length and time scales of surface fluctuations from point measurements is also difficult. Imaging techniques with different dimensionality, however, may close this gap. It is shown in this thesis that edge detection methods (known from computer vision) may be used for two-dimensional free-surface extraction (i.e. from images taken through transparant sidewalls in laboratory flumes). Another opportunity in hydraulic laboratory studies comes with the application of stereo vision. Low-cost RGB-D sensors can be used to gather instantaneous, three-dimensional free-surface elevations, even in flows with very high complexity (e.g. aerated hydraulic jumps). It will be shown that the uncertainty of these methods is of similar order as for classical instruments. Particle Image Velocimetry (PIV) is a well-accepted and widespread imaging technique for velocity determination in laboratory conditions. In combination with high-speed cameras, PIV can give time-resolved velocity fields in 2D/3D or even as volumetric flow fields. PIV is based on a cross-correlation technique applied to small subimages of seeded flows. The minimum size of these subimages defines the maximum spatial resolution of resulting velocity fields. A derivative of PIV for aerated flows is also available, i.e. the so-called Bubble Image Velocimetry (BIV). This thesis emphasizes the capacities and limitations of both methods, using relatively simple setups with halogen and LED illuminations. It will be demonstrated that PIV/BIV images may also be processed by means of Optical Flow (OF) techniques. OF is another method originating from the computer vision discipline, based on the assumption of image brightness conservation within a sequence of images. The Horn-Schunck approach, which has been first employed to hydraulic engineering problems in the studies presented herein, yields dense velocity fields, i.e. pixelwise velocity data. As discussed hereinafter, the accuracy of OF competes well with PIV for clear-water flows and even improves results (compared to BIV) for aerated flow conditions. In order to independently benchmark the OF approach, synthetic images with defined turbulence intensitiy are used. Computer vision offers new opportunities that may help to improve the understanding of fluid mechanics and fluid-structure interactions in laboratory investigations. In prototype environments, it can be employed for obstacle detection (e.g. identification of potential fish migration corridors) and recognition (e.g. fish species for monitoring in a fishway) or surface reconstruction (e.g. inspection of hydraulic structures). It can thus be expected that applications to hydraulic engineering problems will develop rapidly in near future. Current methods have not been developed for fluids in motion. Systematic future developments are needed to improve the results in such difficult conditions.}, language = {en} } @article{KleefeldPieronek2020, author = {Kleefeld, Andreas and Pieronek, J.}, title = {Elastic transmission eigenvalues and their computation via the method of fundamental solutions}, series = {Applicable Analysis}, volume = {100}, journal = {Applicable Analysis}, number = {16}, publisher = {Taylore \& Francis}, address = {London}, issn = {1563-504X}, doi = {10.1080/00036811.2020.1721473}, pages = {3445 -- 3462}, year = {2020}, abstract = {A stabilized version of the fundamental solution method to catch ill-conditioning effects is investigated with focus on the computation of complex-valued elastic interior transmission eigenvalues in two dimensions for homogeneous and isotropic media. Its algorithm can be implemented very shortly and adopts to many similar partial differential equation-based eigenproblems as long as the underlying fundamental solution function can be easily generated. We develop a corroborative approximation analysis which also implicates new basic results for transmission eigenfunctions and present some numerical examples which together prove successful feasibility of our eigenvalue recovery approach.}, language = {en} } @inproceedings{MayntzKeimerDahmannetal.2022, author = {Mayntz, Joscha and Keimer, Jona and Dahmann, Peter and Hille, Sebastian and Stumpf, Eike and Fisher, Alex and Dorrington, Graham}, title = {Electrical Drive and Regeneration in General Aviation Flight with Propellers}, series = {Deutscher Luft- und Raumfahrtkongress 2020}, booktitle = {Deutscher Luft- und Raumfahrtkongress 2020}, publisher = {DGLR}, address = {Bonn}, doi = {10.25967/530100}, pages = {8 Seiten}, year = {2022}, abstract = {Electric flight has the potential for a more sustainable and energy-saving way of aviation compared to fossil fuel aviation. The electric motor can be used as a generator inflight to regenerate energy during descent. Three different approaches to regenerating with electric propeller powertrains are proposed in this paper. The powertrain is to be set up in a wind tunnel to determine the propeller efficiency in both working modes as well as the noise emissions. Furthermore, the planned flight tests are discussed. In preparation for these tests, a yaw stability analysis is performed with the result that the aeroplane is controllable during flight and in the most critical failure case. The paper shows the potential for inflight regeneration and addresses the research gaps in the dual role of electric powertrains for propulsion and regeneration of general aviation aircraft.}, language = {en} } @misc{MayntzKeimerTegtmeyeretal.2021, author = {Mayntz, Joscha and Keimer, Jona and Tegtmeyer, Philipp and Dahmann, Peter and Hille, Sebastian and Stumpf, Eike and Fisher, Alex and Dorrington, Graham}, title = {Aerodynamic Investigation on Efficient Inflight Transition of a Propeller from Propulsion to Regeneration Mode}, series = {AIAA SCITECH 2022 Forum}, journal = {AIAA SCITECH 2022 Forum}, publisher = {AIAA}, address = {Reston, Va.}, doi = {10.2514/6.2022-0546}, year = {2021}, abstract = {This paper discusses a new way of inflight power regeneration for electric or hybrid-electric driven general aviation aircraft with one powertrain for both configurations. Three different approaches for the shift from propulsion to regeneration mode are analyzed. Numerical cal-culation and wind tunnel results are compared and show the highest regeneration potential for the "Windmill" approach, where the propeller blades are flipped, and rotation is reversed. A combination of all regeneration approaches for a realistic flight mission is discussed.}, language = {en} } @article{SaretzkiBergmannDahmannetal.2021, author = {Saretzki, Charlotte and Bergmann, Ole and Dahmann, Peter and Janser, Frank and Keimer, Jona and Machado, Patricia and Morrison, Audry and Page, Henry and Pluta, Emil and St{\"u}bing, Felix and K{\"u}pper, Thomas}, title = {Are small airplanes safe with regards to COVID-19 transmission?}, series = {Journal of Travel Medicine}, volume = {28}, journal = {Journal of Travel Medicine}, number = {7}, publisher = {Oxford University Press}, address = {Oxford}, issn = {1708-8305}, doi = {10.1093/jtm/taab105}, year = {2021}, language = {en} } @inproceedings{TreulingCzarneckiWolf2023, author = {Treuling, Clemens and Czarnecki, Christian and Wolf, Martin}, title = {Projekt WiLMo - Wirtschaftsinformatik Lehr- und Lernmodule}, series = {Angewandte Forschung in der Wirtschaftsinformatik 2023 : Tagungsband zur 36. AKWI-Jahrestagung}, booktitle = {Angewandte Forschung in der Wirtschaftsinformatik 2023 : Tagungsband zur 36. AKWI-Jahrestagung}, pages = {161 -- 169}, year = {2023}, abstract = {Die potenziellen Auswirkungen der Digitalisierung auf die Lehre sind seit langem Gegenstand ausf{\"u}hrlicher Diskussionen innerhalb der Wirtschaftsinformatik (WI) (z. B. in Auth et al. 2021, Barton et al. 2019, Klotz et al. 2019). Nicht zuletzt der in nahezu allen Wirtschaftszweigen bestehende Mangel an qualifizierten Fachkr{\"a}ften lenkt den Diskurs auf einen verbesserten Zugang zu Bildung und gleichen Bildungschancen. Aus dieser Vision heraus und dem Schub der Digitalisierung entstehen Bildungskonzepte wie Open Educational Resources (OER), die gesellschaftlichen Problemen, wie dem des Fachkr{\"a}ftemangels, entgegenwirken sollen. Im Rahmen dieses Kurzbeitrags wird das Projekt WiLMo - "Wirtschaftsinformatik Lehr- und Lernmodule" vorgestellt. WiLMo wird im Rahmen von OERContent.nrw unter Beteiligung von sechs Hochschulen entwickelt und gef{\"o}rdert. Alle Projektbeteiligten arbeiten gemeinsam daran, einheitliche digitale Lehr- und Lernmaterialien im OER-Format f{\"u}r die Kernmodule der Wirtschaftsinformatik zu entwickeln und in garantiert hoher Qualit{\"a}t zur Verf{\"u}gung zu stellen.}, language = {de} } @misc{KeimerGirbigMayntzetal.2022, author = {Keimer, Jona and Girbig, Leo and Mayntz, Joscha and Tegtmeyer, Philipp and Wendland, Frederik and Dahman, Peter and Fisher, Alex and Dorrington, Graham}, title = {Flight mission optimization for eco-efficiency in consideration of electric regeneration and atmospheric conditions}, series = {AIAA AVIATION 2022 Forum}, journal = {AIAA AVIATION 2022 Forum}, publisher = {AIAA}, address = {Reston, Va.}, doi = {10.2514/6.2022-4118}, year = {2022}, abstract = {The development and operation of hybrid or purely electrically powered aircraft in regional air mobility is a significant challenge for the entire aviation sector. This technology is expected to lead to substantial advances in flight performance, energy efficiency, reliability, safety, noise reduction, and exhaust emissions. Nevertheless, any consumed energy results in heat or carbon dioxide emissions and limited electric energy storage capabilities suppress commercial use. Therefore, the significant challenges to achieving eco-efficient aviation are increased aircraft efficiency, the development of new energy storage technologies, and the optimization of flight operations. Two major approaches for higher eco-efficiency are identified: The first one, is to take horizontal and vertical atmospheric motion phenomena into account. Where, in particular, atmospheric waves hold exciting potential. The second one is the use of the regeneration ability of electric aircraft. The fusion of both strategies is expected to improve efficiency. The objective is to reduce energy consumption during flight while not neglecting commercial usability and convenient flight characteristics. Therefore, an optimized control problem based on a general aviation class aircraft has to be developed and validated by flight experiments. The formulated approach enables a development of detailed knowledge of the potential and limitations of optimizing flight missions, considering the capability of regeneration and atmospheric influences to increase efficiency and range.}, language = {en} } @book{Czarnecki2023, author = {Czarnecki, Christian}, title = {Angewandte Forschung in der Wirtschaftsinformatik 2023 : Tagungsband zur 36. AKWI-Jahrestagung}, editor = {Czarnecki, Christian and L{\"u}bbe, Alexander and Meister, Vera G. and M{\"u}ller, Christian and Steglich, Mike and Walther, Mathias}, organization = {Arbeitskreis Wirtschaftsinformatik an Hochschulen f{\"u}r Angewandte Wissenschaften im deutschsprachigen Raum (AKWI)}, doi = {10.15771/1794}, pages = {214 Seiten}, year = {2023}, abstract = {Beitr{\"a}ge der Fachtagung „Angewandte Forschung in der Wirtschaftsinformatik - Zukunft gestalten" im Rahmen der 36. Jahrestagung des Arbeitskreises Wirtschaftsinformatik an Hochschulen f{\"u}r Angewandte Wissenschaften (AKWI) vom 11. bis 13.09.2023 an der Technischen Hochschule Wildau}, language = {de} } @article{Bung2024, author = {Bung, Daniel Bernhard}, title = {Kamerabasierte Fließtiefen- und Geschwindigkeitsmessungen}, series = {Wasserwirtschaft}, volume = {114}, journal = {Wasserwirtschaft}, number = {4}, publisher = {Springer Vieweg}, address = {Wiesbaden}, issn = {0043-0978}, pages = {47 -- 53}, year = {2024}, abstract = {In der wasserbaulichen Forschung werden neben klassischen Messinstrumenten zunehmend kamerabasierte Verfahren genutzt. Diese erlauben neben der Bestimmung von Fließgeschwindigkeiten auch die Detektion der freien Wasseroberfl{\"a}che oder zeitliche Vermessung von Kolken. Durch die hohen r{\"a}umlichen und zeitlichen Aufl{\"o}sungen, welche neueste Kamerasensoren liefern, k{\"o}nnen neue Erkenntnisse in turbulenten, komplexen Str{\"o}mungen gewonnen werden. Auch in der Praxis k{\"o}nnen diese Verfahren mit geringem Aufwand wichtige Daten liefern.}, language = {de} } @incollection{SchultLosseCzarneckietal.2023, author = {Schult, Prince Garcia and Losse, Ann-Kathrin and Czarnecki, Christian and Sultanow, Eldar}, title = {Proposing a Framework to address the Sustainable Development Goals}, series = {EnviroInfo 2023}, booktitle = {EnviroInfo 2023}, publisher = {GI - Gesellschaft f{\"u}r Informatik}, address = {Bonn}, isbn = {978-3-88579-736-4}, issn = {1617-5468}, doi = {10.18420/env2023-022}, pages = {243 -- 249}, year = {2023}, abstract = {Reducing poverty, protecting the planet, and improving life on earth for everyone are the essential goals of the "2030 Agenda for Sustainable Development"committed by the United Nations (UN). Achieving those goals will require technological innovation as well as their implementation in almost all areas of our business and day-to-day life. This paper proposes a high-level framework that collects and structures different uses cases addressing the goals defined by the UN. Hence, it contributes to the discussion by proposing technical innovations that can be used to achieve those goals. As an example, the goal "Climate Action{\"i}s discussed in detail by describing use cases related to tackling biodiversity loss in order to conservate ecosystems.}, language = {en} } @article{OertelBung2021, author = {Oertel, Mario and Bung, Daniel Bernhard}, title = {Hochwasserschutz - eine Aufgabe f{\"u}r eine nachhaltige Wasserwirtschaft}, series = {Wasserwirtschaft}, volume = {111}, journal = {Wasserwirtschaft}, number = {9-10}, publisher = {Springer Vieweg}, address = {Wiesbaden}, issn = {0043-0978}, pages = {3 -- 19}, year = {2021}, language = {de} } @inproceedings{VladovaUllrichSultanowetal.2023, author = {Vladova, Gergana and Ullrich, Andr{\´e} and Sultanow, Eldar and Tobolla, Marinho and Sebrak, Sebastian and Czarnecki, Christian and Brockmann, Carsten}, title = {Visual analytics for knowledge management}, series = {INFORMATIK 2023 - Designing Futures: Zuk{\"u}nfte gestalten}, booktitle = {INFORMATIK 2023 - Designing Futures: Zuk{\"u}nfte gestalten}, publisher = {GI - Gesellschaft f{\"u}r Informatik}, address = {Bonn}, isbn = {978-3-88579-731-9}, issn = {1617-5468}, doi = {10.18420/inf2023_187}, pages = {1851 -- 1870}, year = {2023}, abstract = {The management of knowledge in organizations considers both established long-term processes and cooperation in agile project teams. Since knowledge can be both tacit and explicit, its transfer from the individual to the organizational knowledge base poses a challenge in organizations. This challenge increases when the fluctuation of knowledge carriers is exceptionally high. Especially in large projects in which external consultants are involved, there is a risk that critical, company-relevant knowledge generated in the project will leave the company with the external knowledge carrier and thus be lost. In this paper, we show the advantages of an early warning system for knowledge management to avoid this loss. In particular, the potential of visual analytics in the context of knowledge management systems is presented and discussed. We present a project for the development of a business-critical software system and discuss the first implementations and results.}, language = {en} } @inproceedings{LosseGehrkeUllrichetal.2022, author = {Losse, Ann-Kathrin and Gehrke, Melanie and Ullrich, Andr{\´e} and Czarnecki, Christian and Sultanow, Eldar and Breithaupt, Carsten and Koch, Christian}, title = {Entwicklung einer Open-Data-Referenzarchitektur f{\"u}r die Luftfahrtindustrie}, series = {INFORMATIK 2022 - Informatik in den Naturwissenschaften, Proceedings}, booktitle = {INFORMATIK 2022 - Informatik in den Naturwissenschaften, Proceedings}, publisher = {GI - Gesellschaft f{\"u}r Informatik}, address = {Bonn}, isbn = {978-3-88579-720-3}, issn = {1617-5468}, doi = {10.18420/inf2022_103}, pages = {1203 -- 1209}, year = {2022}, abstract = {Open Data impliziert die freie Zug{\"a}nglichkeit, Verf{\"u}gbarkeit und Wiederverwendbarkeit von Datens{\"a}tzen. Obwohl hochwertige Datens{\"a}tze {\"o}ffentlich verf{\"u}gbar sind, ist der Zugang zu diesen und die Transparenz {\"u}ber die Formate nicht immer gegeben. Dies mindert die optimale Nutzung des Potenzials zur Wertsch{\"o}pfung, trotz der vorherrschenden Einigkeit {\"u}ber ihre Chancen. Denn Open Data erm{\"o}glicht das Vorantreiben von Compliance-Themen wie Transparenz und Rechenschaftspflicht bis hin zur F{\"o}rderung von Innovationen. Die Nutzung von Open Data erfordert Mut und eine gemeinsame Anstrengung verschiedener Akteure und Branchen. Im Rahmen des vorliegenden Beitrags werden auf Grundlage des Design Science-Ansatzes eine Open Data Capability Map sowie darauf aufbauend eine Datenarchitektur f{\"u}r Open Data in der Luftfahrtindustrie an einem Beispiel entwickelt.}, language = {de} } @article{Bung2021, author = {Bung, Daniel Bernhard}, title = {Extreme flooding in Western Germany: some thoughts on hazards, return periods and risk}, series = {Hydrolink}, journal = {Hydrolink}, number = {4}, publisher = {International Association for Hydro-Environment Engineering and Research (IAHR)}, address = {Madrid}, pages = {108 -- 113}, year = {2021}, abstract = {The low-pressure system Bernd involved extreme rainfalls in the Western part of Germany in July 2021, resulting in major floods, severe damages and a tremendous number of casualties. Such extreme events are rare and full flood protection can never be ensured with reasonable financial means. But still, this event must be starting point to reconsider current design concepts. This article aims at sharing some thoughts on potential hazards, the selection of return periods and remaining risk with the focus on Germany.}, language = {en} } @incollection{AbeleKleefeld2020, author = {Abele, Daniel and Kleefeld, Andreas}, title = {New Numerical Results for the Optimization of Neumann Eigenvalues}, series = {Computational and Analytic Methods in Science and Engineering}, booktitle = {Computational and Analytic Methods in Science and Engineering}, editor = {Constanda, Christian}, publisher = {Birkh{\"a}user}, address = {Cham}, isbn = {978-3-030-48185-8 (Print)}, doi = {10.1007/978-3-030-48186-5_1}, pages = {1 -- 20}, year = {2020}, abstract = {We present new numerical results for shape optimization problems of interior Neumann eigenvalues. This field is not well understood from a theoretical standpoint. The existence of shape maximizers is not proven beyond the first two eigenvalues, so we study the problem numerically. We describe a method to compute the eigenvalues for a given shape that combines the boundary element method with an algorithm for nonlinear eigenvalues. As numerical optimization requires many such evaluations, we put a focus on the efficiency of the method and the implemented routine. The method is well suited for parallelization. Using the resulting fast routines and a specialized parametrization of the shapes, we found improved maxima for several eigenvalues.}, language = {en} } @incollection{PieronekKleefeld2019, author = {Pieronek, Lukas and Kleefeld, Andreas}, title = {The Method of Fundamental Solutions for Computing Interior Transmission Eigenvalues of Inhomogeneous Media}, series = {Integral Methods in Science and Engineering: Analytic Treatment and Numerical Approximations}, booktitle = {Integral Methods in Science and Engineering: Analytic Treatment and Numerical Approximations}, editor = {Constanda, Christian and Harris, Paul}, publisher = {Birkh{\"a}user}, address = {Cham}, isbn = {978-3-030-16077-7}, doi = {10.1007/978-3-030-16077-7_28}, pages = {353 -- 365}, year = {2019}, abstract = {The method of fundamental solutions is applied to the approximate computation of interior transmission eigenvalues for a special class of inhomogeneous media in two dimensions. We give a short approximation analysis accompanied with numerical results that clearly prove practical convenience of our alternative approach.}, language = {en} } @inproceedings{KahraBreussKleefeldetal.2024, author = {Kahra, Marvin and Breuß, Michael and Kleefeld, Andreas and Welk, Martin}, title = {An Approach to Colour Morphological Supremum Formation Using the LogSumExp Approximation}, series = {Discrete Geometry and Mathematical Morphology}, booktitle = {Discrete Geometry and Mathematical Morphology}, editor = {Brunetti, Sara and Frosini, Andrea and Rinaldi, Simone}, publisher = {Springer}, address = {Cham}, isbn = {978-3-031-57793-2}, doi = {10.1007/978-3-031-57793-2_25}, pages = {325 -- 337}, year = {2024}, abstract = {Mathematical morphology is a part of image processing that has proven to be fruitful for numerous applications. Two main operations in mathematical morphology are dilation and erosion. These are based on the construction of a supremum or infimum with respect to an order over the tonal range in a certain section of the image. The tonal ordering can easily be realised in grey-scale morphology, and some morphological methods have been proposed for colour morphology. However, all of these have certain limitations. In this paper we present a novel approach to colour morphology extending upon previous work in the field based on the Loewner order. We propose to consider an approximation of the supremum by means of a log-sum exponentiation introduced by Maslov. We apply this to the embedding of an RGB image in a field of symmetric 2x2 matrices. In this way we obtain nearly isotropic matrices representing colours and the structural advantage of transitivity. In numerical experiments we highlight some remarkable properties of the proposed approach.}, language = {en} } @article{AyalaHarrisKleefeld2024, author = {Ayala, Rafael Ceja and Harris, Isaac and Kleefeld, Andreas}, title = {Direct sampling method via Landweber iteration for an absorbing scatterer with a conductive boundary}, series = {Inverse Problems and Imaging}, volume = {18}, journal = {Inverse Problems and Imaging}, number = {3}, publisher = {AIMS}, address = {Springfield}, issn = {1930-8337}, doi = {10.3934/ipi.2023051}, pages = {708 -- 729}, year = {2024}, abstract = {In this paper, we consider the inverse shape problem of recovering isotropic scatterers with a conductive boundary condition. Here, we assume that the measured far-field data is known at a fixed wave number. Motivated by recent work, we study a new direct sampling indicator based on the Landweber iteration and the factorization method. Therefore, we prove the connection between these reconstruction methods. The method studied here falls under the category of qualitative reconstruction methods where an imaging function is used to recover the absorbing scatterer. We prove stability of our new imaging function as well as derive a discrepancy principle for recovering the regularization parameter. The theoretical results are verified with numerical examples to show how the reconstruction performs by the new Landweber direct sampling method.}, language = {en} } @article{ClausnitzerKleefeld2024, author = {Clausnitzer, Julian and Kleefeld, Andreas}, title = {A spectral Galerkin exponential Euler time-stepping scheme for parabolic SPDEs on two-dimensional domains with a C² boundary}, series = {Discrete and Continuous Dynamical Systems - Series B}, volume = {29}, journal = {Discrete and Continuous Dynamical Systems - Series B}, number = {4}, publisher = {AIMS}, address = {Springfield}, issn = {1531-3492}, doi = {10.3934/dcdsb.2023148}, pages = {1624 -- 1651}, year = {2024}, abstract = {We consider the numerical approximation of second-order semi-linear parabolic stochastic partial differential equations interpreted in the mild sense which we solve on general two-dimensional domains with a C² boundary with homogeneous Dirichlet boundary conditions. The equations are driven by Gaussian additive noise, and several Lipschitz-like conditions are imposed on the nonlinear function. We discretize in space with a spectral Galerkin method and in time using an explicit Euler-like scheme. For irregular shapes, the necessary Dirichlet eigenvalues and eigenfunctions are obtained from a boundary integral equation method. This yields a nonlinear eigenvalue problem, which is discretized using a boundary element collocation method and is solved with the Beyn contour integral algorithm. We present an error analysis as well as numerical results on an exemplary asymmetric shape, and point out limitations of the approach.}, language = {en} } @article{HarrisKleefeld2022, author = {Harris, Isaac and Kleefeld, Andreas}, title = {Analysis and computation of the transmission eigenvalues with a conductive boundary condition}, series = {Applicable Analysis}, volume = {101}, journal = {Applicable Analysis}, number = {6}, publisher = {Taylor \& Francis}, address = {London}, issn = {1563-504X}, doi = {10.1080/00036811.2020.1789598}, pages = {1880 -- 1895}, year = {2022}, abstract = {We provide a new analytical and computational study of the transmission eigenvalues with a conductive boundary condition. These eigenvalues are derived from the scalar inverse scattering problem for an inhomogeneous material with a conductive boundary condition. The goal is to study how these eigenvalues depend on the material parameters in order to estimate the refractive index. The analytical questions we study are: deriving Faber-Krahn type lower bounds, the discreteness and limiting behavior of the transmission eigenvalues as the conductivity tends to infinity for a sign changing contrast. We also provide a numerical study of a new boundary integral equation for computing the eigenvalues. Lastly, using the limiting behavior we will numerically estimate the refractive index from the eigenvalues provided the conductivity is sufficiently large but unknown.}, language = {en} } @article{ChwallekNawrathKrastinaetal.2024, author = {Chwallek, Constanze and Nawrath, Lara and Krastina, Anzelika and Bruksle, Ieva}, title = {Supportive research on sustainable entrepreneurship and business practices}, series = {SECA Sustainable Entrepreneurship for Climate Action}, journal = {SECA Sustainable Entrepreneurship for Climate Action}, number = {3}, publisher = {Lapland University of Applied Sciences Ltd}, address = {Rovaniemi}, isbn = {978-952-316-514-4 (pdf)}, issn = {2954-1654 (on-line publication)}, pages = {67 Seiten}, year = {2024}, language = {en} } @inproceedings{BurgethKleefeldZhangetal.2022, author = {Burgeth, Bernhard and Kleefeld, Andreas and Zhang, Eugene and Zhang, Yue}, title = {Towards Topological Analysis of Non-symmetric Tensor Fields via Complexification}, series = {Discrete Geometry and Mathematical Morphology}, booktitle = {Discrete Geometry and Mathematical Morphology}, editor = {Baudrier, {\´E}tienne and Naegel, Beno{\^i}t and Kr{\"a}henb{\"u}hl, Adrien and Tajine, Mohamed}, publisher = {Springer}, address = {Cham}, isbn = {978-3-031-19897-7}, doi = {10.1007/978-3-031-19897-7_5}, pages = {48 -- 59}, year = {2022}, abstract = {Fields of asymmetric tensors play an important role in many applications such as medical imaging (diffusion tensor magnetic resonance imaging), physics, and civil engineering (for example Cauchy-Green-deformation tensor, strain tensor with local rotations, etc.). However, such asymmetric tensors are usually symmetrized and then further processed. Using this procedure results in a loss of information. A new method for the processing of asymmetric tensor fields is proposed restricting our attention to tensors of second-order given by a 2x2 array or matrix with real entries. This is achieved by a transformation resulting in Hermitian matrices that have an eigendecomposition similar to symmetric matrices. With this new idea numerical results for real-world data arising from a deformation of an object by external forces are given. It is shown that the asymmetric part indeed contains valuable information.}, language = {en} } @article{KleefeldZimmermann2022, author = {Kleefeld, Andreas and Zimmermann, M.}, title = {Computing Elastic Interior Transmission Eigenvalues}, series = {Integral Methods in Science and Engineering}, journal = {Integral Methods in Science and Engineering}, editor = {Constanda, Christian and Bodmann, Bardo E.J. and Harris, Paul J.}, publisher = {Birkh{\"a}user}, address = {Cham}, isbn = {978-3-031-07171-3}, doi = {10.1007/978-3-031-07171-3_10}, pages = {139 -- 155}, year = {2022}, abstract = {An alternative method is presented to numerically compute interior elastic transmission eigenvalues for various domains in two dimensions. This is achieved by discretizing the resulting system of boundary integral equations in combination with a nonlinear eigenvalue solver. Numerical results are given to show that this new approach can provide better results than the finite element method when dealing with general domains.}, language = {en} } @misc{BurgethKleefeldNaegeletal.2020, author = {Burgeth, Bernhard and Kleefeld, Andreas and Naegel, Beno{\^i}t and Perret, Benjamin}, title = {Editorial — Special Issue: ISMM 2019}, series = {Mathematical Morphology - Theory and Applications}, volume = {4}, journal = {Mathematical Morphology - Theory and Applications}, number = {1}, publisher = {De Gruyter}, address = {Warschau}, issn = {2353-3390}, doi = {10.1515/mathm-2020-0200}, pages = {159 -- 161}, year = {2020}, abstract = {This editorial presents the Special Issue dedicated to the conference ISMM 2019 and summarizes the articles published in this Special Issue.}, language = {en} } @article{Kleefeld2021, author = {Kleefeld, Andreas}, title = {The hot spots conjecture can be false: some numerical examples}, series = {Advances in Computational Mathematics}, volume = {47}, journal = {Advances in Computational Mathematics}, publisher = {Springer}, address = {Dordrecht}, issn = {1019-7168}, doi = {10.1007/s10444-021-09911-5}, year = {2021}, abstract = {The hot spots conjecture is only known to be true for special geometries. This paper shows numerically that the hot spots conjecture can fail to be true for easy to construct bounded domains with one hole. The underlying eigenvalue problem for the Laplace equation with Neumann boundary condition is solved with boundary integral equations yielding a non-linear eigenvalue problem. Its discretization via the boundary element collocation method in combination with the algorithm by Beyn yields highly accurate results both for the first non-zero eigenvalue and its corresponding eigenfunction which is due to superconvergence. Additionally, it can be shown numerically that the ratio between the maximal/minimal value inside the domain and its maximal/minimal value on the boundary can be larger than 1 + 10- 3. Finally, numerical examples for easy to construct domains with up to five holes are provided which fail the hot spots conjecture as well.}, language = {en} } @article{MartinVaqueroKleefeld2020, author = {Mart{\´i}n-Vaquero, J. and Kleefeld, Andreas}, title = {Solving nonlinear parabolic PDEs in several dimensions: Parallelized ESERK codes}, series = {Journal of Computational Physics}, journal = {Journal of Computational Physics}, number = {423}, publisher = {Elsevier}, address = {Amsterdam}, issn = {0021-9991}, doi = {10.1016/j.jcp.2020.109771}, year = {2020}, abstract = {There is a very large number of very important situations which can be modeled with nonlinear parabolic partial differential equations (PDEs) in several dimensions. In general, these PDEs can be solved by discretizing in the spatial variables and transforming them into huge systems of ordinary differential equations (ODEs), which are very stiff. Therefore, standard explicit methods require a large number of iterations to solve stiff problems. But implicit schemes are computationally very expensive when solving huge systems of nonlinear ODEs. Several families of Extrapolated Stabilized Explicit Runge-Kutta schemes (ESERK) with different order of accuracy (3 to 6) are derived and analyzed in this work. They are explicit methods, with stability regions extended, along the negative real semi-axis, quadratically with respect to the number of stages s, hence they can be considered to solve stiff problems much faster than traditional explicit schemes. Additionally, they allow the adaptation of the step length easily with a very small cost. Two new families of ESERK schemes (ESERK3 and ESERK6) are derived, and analyzed, in this work. Each family has more than 50 new schemes, with up to 84.000 stages in the case of ESERK6. For the first time, we also parallelized all these new variable step length and variable number of stages algorithms (ESERK3, ESERK4, ESERK5, and ESERK6). These parallelized strategies allow to decrease times significantly, as it is discussed and also shown numerically in two problems. Thus, the new codes provide very good results compared to other well-known ODE solvers. Finally, a new strategy is proposed to increase the efficiency of these schemes, and it is discussed the idea of combining ESERK families in one code, because typically, stiff problems have different zones and according to them and the requested tolerance the optimum order of convergence is different.}, language = {en} } @incollection{Kleefeld2020, author = {Kleefeld, Andreas}, title = {Numerical calculation of interior transmission eigenvalues with mixed boundary conditions}, series = {Computational and Analytic Methods in Science and Engineering}, booktitle = {Computational and Analytic Methods in Science and Engineering}, editor = {Constanda, Christian}, publisher = {Birkh{\"a}user}, address = {Cham}, isbn = {978-3-030-48185-8 (Hardcover)}, doi = {10.1007/978-3-030-48186-5_9}, pages = {173 -- 195}, year = {2020}, abstract = {Interior transmission eigenvalue problems for the Helmholtz equation play an important role in inverse wave scattering. Some distribution properties of those eigenvalues in the complex plane are reviewed. Further, a new scattering model for the interior transmission eigenvalue problem with mixed boundary conditions is described and an efficient algorithm for computing the interior transmission eigenvalues is proposed. Finally, extensive numerical results for a variety of two-dimensional scatterers are presented to show the validity of the proposed scheme.}, language = {en} } @article{AsanteAsamaniKleefeldWade2020, author = {Asante-Asamani, E.O. and Kleefeld, Andreas and Wade, B.A.}, title = {A second-order exponential time differencing scheme for non-linear reaction-diffusion systems with dimensional splitting}, series = {Journal of Computational Physics}, volume = {415}, journal = {Journal of Computational Physics}, publisher = {Elsevier}, address = {Amsterdam}, issn = {0021-9991}, doi = {10.1016/j.jcp.2020.109490}, year = {2020}, abstract = {A second-order L-stable exponential time-differencing (ETD) method is developed by combining an ETD scheme with approximating the matrix exponentials by rational functions having real distinct poles (RDP), together with a dimensional splitting integrating factor technique. A variety of non-linear reaction-diffusion equations in two and three dimensions with either Dirichlet, Neumann, or periodic boundary conditions are solved with this scheme and shown to outperform a variety of other second-order implicit-explicit schemes. An additional performance boost is gained through further use of basic parallelization techniques.}, language = {en} } @article{BreussKleefeld2020, author = {Breuß, Michael and Kleefeld, Andreas}, title = {Implicit monotone difference methods for scalar conservation laws with source terms}, series = {Acta Mathematica Vietnamica}, volume = {45}, journal = {Acta Mathematica Vietnamica}, publisher = {Springer Singapore}, address = {Singapore}, issn = {2315-4144}, doi = {10.1007/s40306-019-00354-1}, pages = {709 -- 738}, year = {2020}, abstract = {In this article, a concept of implicit methods for scalar conservation laws in one or more spatial dimensions allowing also for source terms of various types is presented. This material is a significant extension of previous work of the first author (Breuß SIAM J. Numer. Anal. 43(3), 970-986 2005). Implicit notions are developed that are centered around a monotonicity criterion. We demonstrate a connection between a numerical scheme and a discrete entropy inequality, which is based on a classical approach by Crandall and Majda. Additionally, three implicit methods are investigated using the developed notions. Next, we conduct a convergence proof which is not based on a classical compactness argument. Finally, the theoretical results are confirmed by various numerical tests.}, language = {en} } @article{HarrisKleefeld2018, author = {Harris, Isaac and Kleefeld, Andreas}, title = {The inverse scattering problem for a conductive boundary condition and transmission eigenvalues}, series = {Applicable Analysis}, volume = {99}, journal = {Applicable Analysis}, number = {3}, publisher = {Taylor \& Francis}, address = {London}, issn = {1563-504X}, doi = {10.1080/00036811.2018.1504028}, pages = {508 -- 529}, year = {2018}, abstract = {In this paper, we consider the inverse scattering problem associated with an inhomogeneous media with a conductive boundary. In particular, we are interested in two problems that arise from this inverse problem: the inverse conductivity problem and the corresponding interior transmission eigenvalue problem. The inverse conductivity problem is to recover the conductive boundary parameter from the measured scattering data. We prove that the measured scatted data uniquely determine the conductivity parameter as well as describe a direct algorithm to recover the conductivity. The interior transmission eigenvalue problem is an eigenvalue problem associated with the inverse scattering of such materials. We investigate the convergence of the eigenvalues as the conductivity parameter tends to zero as well as prove existence and discreteness for the case of an absorbing media. Lastly, several numerical and analytical results support the theory and we show that the inside-outside duality method can be used to reconstruct the interior conductive eigenvalues.}, language = {en} } @article{FiedlerOrzadaFloeseretal.2021, author = {Fiedler, Thomas M. and Orzada, Stephan and Fl{\"o}ser, Martina and Rietsch, Stefan H. G. and Quick, Harald H. and Ladd, Mark E. and Bitz, Andreas}, title = {Performance analysis of integrated RF microstrip transmit antenna arrays with high channel count for body imaging at 7 T}, series = {NMR in Biomedicine}, volume = {34}, journal = {NMR in Biomedicine}, number = {7}, publisher = {Wiley}, address = {Weinheim}, issn = {0952-3480 (ISSN)}, doi = {10.1002/nbm.4515}, pages = {18 SeitenWiley}, year = {2021}, abstract = {The aim of the current study was to investigate the performance of integrated RF transmit arrays with high channel count consisting of meander microstrip antennas for body imaging at 7 T and to optimize the position and number of transmit ele- ments. RF simulations using multiring antenna arrays placed behind the bore liner were performed for realistic exposure conditions for body imaging. Simulations were performed for arrays with as few as eight elements and for arrays with high channel counts of up to 48 elements. The B1+ field was evaluated regarding the degrees of freedom for RF shimming in the abdomen. Worst-case specific absorption rate (SARwc ), SAR overestimation in the matrix compression, the number of virtual obser- vation points (VOPs) and SAR efficiency were evaluated. Constrained RF shimming was performed in differently oriented regions of interest in the body, and the devia- tion from a target B1+ field was evaluated. Results show that integrated multiring arrays are able to generate homogeneous B1+ field distributions for large FOVs, espe- cially for coronal/sagittal slices, and thus enable body imaging at 7 T with a clinical workflow; however, a low duty cycle or a high SAR is required to achieve homoge- neous B1+ distributions and to exploit the full potential. In conclusion, integrated arrays allow for high element counts that have high degrees of freedom for the pulse optimization but also produce high SARwc , which reduces the SAR accuracy in the VOP compression for low-SAR protocols, leading to a potential reduction in array performance. Smaller SAR overestimations can increase SAR accuracy, but lead to a high number of VOPs, which increases the computational cost for VOP evaluation and makes online SAR monitoring or pulse optimization challenging. Arrays with interleaved rings showed the best results in the study.}, language = {en} } @techreport{HoffmannUllrich2024, type = {Working Paper}, author = {Hoffmann, Sarah and Ullrich, Anna Valentine}, title = {30 Minuten FDM f{\"u}r HAW. Ein Informationsformat f{\"u}r Forschende an HAW in NRW}, doi = {10.5281/zenodo.12569282}, pages = {1 Seite}, year = {2024}, abstract = {Wie kann man das Thema Forschungsdatenmanagement (FDM) konkret und anwendbar f{\"u}r Forschende gestalten, die bisher noch wenig Kontakt damit hatten? Auf diese Frage gibt das Konzept „30 Minuten FDM f{\"u}r HAW. Ein Informationsformat f{\"u}r Forschende an HAW in NRW" eine Antwort. Es entstand als Projektarbeit im Zertifikatskurs Forschungsdatenmanagement 2023/24}, language = {de} } @techreport{BirmansSchickTamborninoetal.2024, type = {Working Paper}, author = {Birmans, Katrin and Schick, Elena and Tambornino, Philipp and Ullrich, Anna Valentine}, title = {Ingenieurwissenschaften im Fokus: Zug{\"a}nge zu einem effektiven Forschungsdatenmanagement an HAW}, doi = {10.5281/zenodo.12545429}, pages = {49 Seiten}, year = {2024}, abstract = {Im Rahmen der Love Data Week vom 12. bis 16.02.2024 haben die BMBF-Projekte FDM2_TH_Koeln der TH K{\"o}ln (FK 16FDFH105) und Persist@HAW der FH Aachen (FK 16FDFH129) am 15.02.2024 gemeinsam eine Online-Veranstaltung mit dem Titel „Ingenieurwissenschaften im Fokus: Zug{\"a}nge zu einem effektiven Forschungsdatenmanagement an HAW" angeboten. Diese richtete sich an Forschende aus den Ingenieurwissenschaften, die einen ersten Zugang zum Thema Forschungsdatenmanagement (FDM) suchen und erfahren m{\"o}chten, welche speziellen Angebote f{\"u}r die Daten aus den Ingenieurwissenschaften existieren. In der Veranstaltung wurden wesentliche Aspekte des Forschungsdatenmanagements entlang des Datenlebenszyklus beleuchtet. Ziel war es, den Teilnehmenden praxisnahe Einblicke und Hilfestellungen zu einem effektiven Umgang mit Forschungsdaten an Hochschulen f{\"u}r Angewandte Wissenschaften (HAW) zu bieten. Durch Beispiele und konkrete Empfehlungen wurde das Thema zug{\"a}nglich gemacht.}, language = {de} } @techreport{BirmansTamborninoUllrich2024, type = {Working Paper}, author = {Birmans, Katrin and Tambornino, Philipp and Ullrich, Anna Valentine}, title = {Bevor Sie Coscine nutzen - Handreichung f{\"u}r Forschende an HAW}, doi = {10.5281/zenodo.12158546}, pages = {2 Seiten}, year = {2024}, abstract = {Um die Forschungsdatenmanagement-Plattform Coscine optimal f{\"u}r Forschungsprojekte nutzen zu k{\"o}nnen, ist es sinnvoll, einige Fragen im Vorhinein zu kl{\"a}ren. So k{\"o}nnen aufwendige {\"A}nderungen der Datenverwaltung im Nachhinein vermieden werden. Hierzu bietet die Handreichung hilfreiche Leitfragen und Erl{\"a}uterungen f{\"u}r Forschende und FDM-Service-Personal an HAW in NRW (DH.NRW-Hochschulen). FDM-Service-Mitarbeitende k{\"o}nnen die Handreichung in ihrer Beratung zu Coscine einsetzen und mit der Eingabemaske in der Kopfzeile des Dokuments auf ihre Hochschule anpassen.}, language = {de} } @techreport{BirmansTamborninoUllrich2024, type = {Working Paper}, author = {Birmans, Katrin and Tambornino, Philipp and Ullrich, Anna Valentine}, title = {5 Gr{\"u}nde f{\"u}r Coscine - Handreichung f{\"u}r Forschende an HAW}, doi = {10.5281/zenodo.12156734}, pages = {1 Seite}, year = {2024}, abstract = {Welche Vorteile bietet die Forschungsdatenmanagement-Plattform Coscine f{\"u}r die Verwaltung von Daten in Forschungsprojekten? Hierzu gibt die Handreichung einen schnellen {\"U}berblick {\"u}ber den landesgef{\"o}rderten Dienst Coscine f{\"u}r Forschende und FDM-Service-Personal an HAW in NRW (DH.NRW-Hochschulen). FDM-Service-Mitarbeitende k{\"o}nnen die Handreichung in ihrer Beratung zu Coscine einsetzen und mit der Eingabemaske in der Kopfzeile des Dokuments auf ihre Hochschule anpassen.}, language = {de} } @inproceedings{BeckerBragard2024, author = {Becker, Tim and Bragard, Michael}, title = {Low-Voltage DC Training Lab for Electric Drives - Optimizing the Balancing Act Between High Student Throughput and Individual Learning Speed}, series = {2024 IEEE Global Engineering Education Conference (EDUCON)}, booktitle = {2024 IEEE Global Engineering Education Conference (EDUCON)}, publisher = {IEEE}, address = {New York, NY}, issn = {2165-9559}, doi = {10.1109/EDUCON60312.2024.10578902}, pages = {8 Seiten}, year = {2024}, abstract = {After a brief introduction of conventional laboratory structures, this work focuses on an innovative and universal approach for a setup of a training laboratory for electric machines and drive systems. The novel approach employs a central 48 V DC bus, which forms the backbone of the structure. Several sets of DC machine, asynchronous machine and synchronous machine are connected to this bus. The advantages of the novel system structure are manifold, both from a didactic and a technical point of view: Student groups can work on their own performance level in a highly parallelized and at the same time individualized way. Additional training setups (similar or different) can easily be added. Only the total power dissipation has to be provided, i.e. the DC bus balances the power flow between the student groups. Comparative results of course evaluations of several cohorts of students are shown.}, language = {en} } @inproceedings{RuettersBragardDolls2024, author = {R{\"u}tters, Ren{\´e} and Bragard, Michael and Dolls, Sarah}, title = {The Inverted Rotary Pendulum: Facilitating Practical Teaching in Advanced Control Engineering}, series = {2024 IEEE Global Engineering Education Conference (EDUCON)}, booktitle = {2024 IEEE Global Engineering Education Conference (EDUCON)}, publisher = {IEEE}, address = {New York, NY}, issn = {2165-9559}, doi = {10.1109/EDUCON60312.2024.10578937}, pages = {5 Seiten}, year = {2024}, abstract = {This paper outlines a practical approach to teach control engineering principles, with an inverted rotary pendulum, serving as an illustrative example. It shows how the pendulum is embedded in an advanced course of control engineering. This approach is incorporated into a flipped-classroom concept, as well as classical teaching concepts, offering students practical experience in control engineering. In addition, the design of the pendulum is shown, using a Raspberry Pi as the target platform for Matlab Simulink. This pendulum can be used in the classroom to evaluate the controller design mentioned above. It is analysed if the use of the pendulum generates a deeper understanding of the learning contents.}, language = {en} } @inproceedings{KramerBragardRitzetal.2024, author = {Kramer, Pia and Bragard, Michael and Ritz, Thomas and Ferfer, Ute and Schiffers, Tim}, title = {Visualizing, Enhancing and Predicting Students' Success through ECTS Monitoring}, series = {2024 IEEE Global Engineering Education Conference (EDUCON)}, booktitle = {2024 IEEE Global Engineering Education Conference (EDUCON)}, publisher = {IEEE}, address = {New York, NY}, issn = {2165-9559}, doi = {10.1109/EDUCON60312.2024.10578652}, pages = {5 Seiten}, year = {2024}, abstract = {This paper serves as an introduction to the ECTS monitoring system and its potential applications in higher education. It also emphasizes the potential for ECTS monitoring to become a proactive system, supporting students by predicting academic success and identifying groups of potential dropouts for tailored support services. The use of the nearest neighbor analysis is suggested for improving data analysis and prediction accuracy.}, language = {en} } @techreport{BarnatArntzBerneckeretal.2024, type = {Working Paper}, author = {Barnat, Miriam and Arntz, Kristian and Bernecker, Andreas and Fissabre, Anke and Franken, Norbert and Goldbach, Daniel and H{\"u}ning, Felix and J{\"o}rissen, J{\"o}rg and Kirsch, Ansgar and Pettrak, J{\"u}rgen and Rexforth, Matthias and Josef, Rosenkranz and Terstegge, Andreas}, title = {Strategische Gestaltung von Studieng{\"a}ngen f{\"u}r die Zukunft: Ein kollaborativ entwickeltes Self-Assessment}, series = {Hochschulforum Digitalisierung - Diskussionspapier}, journal = {Hochschulforum Digitalisierung - Diskussionspapier}, publisher = {Stifterverband f{\"u}r die Deutsche Wissenschaft}, address = {Berlin}, issn = {2365-7081}, pages = {16 Seiten}, year = {2024}, abstract = {Das Diskussionspapier beschreibt einen Prozess an der FH Aachen zur Entwicklung und Implementierung eines Self-Assessment-Tools f{\"u}r Studieng{\"a}nge. Dieser Prozess zielte darauf ab, die Relevanz der Themen Digitalisierung, Internationalisierung und Nachhaltigkeit in Studieng{\"a}ngen zu st{\"a}rken. Durch Workshops und kollaborative Entwicklung mit Studiendekan:innen entstand ein Fragebogen, der zur Reflexion und strategischen Weiterentwicklung der Studieng{\"a}nge dient.}, language = {de} } @article{GollandKriegesmann2023, author = {Golland, Alexander and Kriegesmann, Torben}, title = {Zivilprozessuale Fragen zum datenschutzrechtlichen Schadensersatzanspruch}, series = {MMR - Zeitschrift f{\"u}r IT-Recht und Recht der Digitalisierung}, journal = {MMR - Zeitschrift f{\"u}r IT-Recht und Recht der Digitalisierung}, number = {10}, publisher = {Beck}, address = {M{\"u}nchen}, issn = {2698-7988}, pages = {733 -- 739}, year = {2023}, abstract = {Im Verfahren gegen die {\"O}sterreichische Post AG (Rs. C-300/21) befasste sich der EuGH erstmals mit dem in Art. 82 DS-GVO geregelten datenschutzrechtlichen Schadensersatzanspruch. Mit den Klarstellungen des EuGH verschieben sich die Probleme nun st{\"a}rker zu den „klassischen" Fragen des Schadensersatzrechts im Zivilprozess. Relevant sind dabei vor allem Aspekte der Darlegungs- und Beweislast und deren Besonderheiten mit Blick auf den Ersatz immaterieller Sch{\"a}den. Der Beitrag fokussiert sich auf die Voraussetzungen und den dabei zu f{\"u}hrenden Tatsachenbeweis bei der Klage des Betroffenen gegen den Verantwortlichen auf Ersatz immaterieller Sch{\"a}den.}, language = {de} } @incollection{Golland2024, author = {Golland, Alexander}, title = {Kommentierung von \S\S 6 bis 10 EKD-Datenschutzgesetz}, series = {EKD-Datenschutzgesetz. Datenschutzbestimmungen der evangelischen Kirche}, booktitle = {EKD-Datenschutzgesetz. Datenschutzbestimmungen der evangelischen Kirche}, editor = {Wagner, Ralph}, publisher = {Nomos}, address = {Baden-Baden}, isbn = {978-3-8487-8111-9}, pages = {153 -- 228}, year = {2024}, language = {de} } @article{GollandKelbch2023, author = {Golland, Alexander and Kelbch, Niklas}, title = {Kartellrecht vs. Datenschutzrecht: Rechtsgrundlagen f{\"u}r die Datenverarbeitung in sozialen Netzwerken}, series = {DSB Datenschutz-Berater}, journal = {DSB Datenschutz-Berater}, number = {9}, publisher = {DFV Mediengruppe}, address = {Frankfurt a.M.}, issn = {0170-7256}, pages = {247 -- 249}, year = {2023}, language = {de} } @article{Golland2023, author = {Golland, Alexander}, title = {Kompetenz nationaler Wettbewerbsbeh{\"o}rden zur Feststellung eines Verstoßes gegen die DS-GVO}, series = {MMR - Zeitschrift f{\"u}r IT-Recht und Recht der Digitalisierung}, journal = {MMR - Zeitschrift f{\"u}r IT-Recht und Recht der Digitalisierung}, number = {9}, publisher = {Beck}, address = {M{\"u}nchen}, pages = {680 -- 683}, year = {2023}, language = {de} } @incollection{Golland2022, author = {Golland, Alexander}, title = {Kommentierung von \S 26 Telekommunikation-Telemedien-Datenschutzgesetz}, series = {TTDSG}, booktitle = {TTDSG}, editor = {Riechert, Anne and Wilmer, Thomas}, publisher = {Erich Schmidt}, address = {Berlin}, isbn = {978-3-503-20978-1}, pages = {439 -- 474}, year = {2022}, language = {de} } @article{Golland2024, author = {Golland, Alexander}, title = {Bußgelder bei Datenschutzverst{\"o}ßen durch Unternehmen}, series = {NJW Neue Juristische Wochenschrift}, journal = {NJW Neue Juristische Wochenschrift}, number = {6}, publisher = {Beck}, address = {M{\"u}nchen}, issn = {0341-1915}, pages = {325 -- 329}, year = {2024}, abstract = {Bald eine Dekade ist es her, dass diese ann{\"a}hernd mantraartig wiederholte Phrase Unternehmen zur Umsetzung datenschutzrechtlicher Vorgaben incentivierte. Was ist davon geblieben? Nur wenige in Deutschland verh{\"a}ngte Bußgelder erreichten Millionenh{\"o}he. Hintergrund ist (auch) das deutsche Ordnungswidrigkeitenrecht, welches in einem Spannungsverh{\"a}ltnis zu den Vorgaben der DS-GVO steht. Ein Bußgeldbescheid der Berliner Datenschutzaufsicht gegen die Deutsche Wohnen sollte Ausl{\"o}ser eines langen, fortdauernden Rechtsstreits werden. Auf Vorlage des KG hatte der EuGH in der Rechtssache C-807/21 („Deutsche Wohnen") erstmals Gelegenheit, sich zur Frage der Bußgeldhaftung zu positionieren.}, language = {de} } @incollection{Golland2022, author = {Golland, Alexander}, title = {Kommentierung von \S 7 Telekommunikation-Telemedien-Datenschutzgesetz}, series = {TTDSG}, booktitle = {TTDSG}, editor = {Riechert, Anne and Wilmer, Thomas}, publisher = {Erich Schmidt}, address = {Berlin}, isbn = {978-3-503-20978-1}, pages = {145 -- 151}, year = {2022}, language = {de} } @article{Golland2024, author = {Golland, Alexander}, title = {Datenschutz beim Einsatz k{\"u}nstlicher Intelligenz im Unternehmen}, series = {NWB}, journal = {NWB}, number = {6}, publisher = {NWB}, address = {Herne}, issn = {0028-3460}, pages = {425 -- 432}, year = {2024}, abstract = {Seit Ende 2022 pr{\"a}gt das Schlagwort „K{\"u}nstliche Intelligenz" (KI) nicht nur den rechtswissenschaftlichen Diskurs. Die allgemeine Verf{\"u}gbarkeit von generativen KI-Modellen, allen voran die großen Sprachmodelle (Large Language Models, kurz: LLM) wie ChatGPT von OpenAI oder Bing AI von Microsoft, erfreuen sich gr{\"o}ßter Beliebtheit: LLM sind in der Lage, auf Grundlage statistischer Methoden - eine entsprechende Schnittstelle (Interface) vorausgesetzt - auch technisch wenig versierten Nutzern verst{\"a}ndliche Antworten auf ihre Fragen zu liefern. Dabei werden nicht nur umfassend Nutzerdaten verarbeitet, sondern auch auf weitere personenbezogene Daten zugegriffen sowie neue Daten erzeugt. Der Beitrag geht der Frage nach, welche spezifischen datenschutzrechtlichen Herausforderungen sich f{\"u}r Unternehmen beim Einsatz solcher LLM stellen.}, language = {de} } @article{GollandSchroeer2024, author = {Golland, Alexander and Schr{\"o}er, Jan-Erik}, title = {No risk, no fun? Ber{\"u}cksichtigung datenschutzrechtlicher Risiken im Vergabeverfahren}, series = {DSB Datenschutz-Berater}, journal = {DSB Datenschutz-Berater}, number = {5}, publisher = {DFV Mediengruppe}, address = {Frankfurt a.M.}, isbn = {0170-7256}, issn = {No risk, no fun? Ber{\"u}cksichtigung datenschutzrechtlicher Risiken im Vergabeverfahren}, pages = {114 -- 117}, year = {2024}, language = {de} } @article{GollandSchroeer2024, author = {Golland, Alexander and Schr{\"o}er, Jan-Erik}, title = {Error 404 im Vergabeverfahren: Datenschutz nicht gefunden?}, series = {VergabeR}, journal = {VergabeR}, number = {2}, publisher = {Wolters Kluwer}, address = {K{\"o}ln}, issn = {2366-2247}, pages = {75 -- 92}, year = {2024}, abstract = {Das Thema Datenschutz wurde bei der {\"o}ffentlichen Auftragsvergabe bislang vor allem in Bezug auf Drittlandtransfers personenbezogener Daten in die USA diskutiert. Jedoch spielt der Datenschutz f{\"u}r das Vergabeverfahren und f{\"u}r die Ausf{\"u}hrung datenschutzrelevanter Leistungen generell eine wesentliche Rolle. Gleichwohl herrschen bislang unter {\"o}ffentlichen Auftraggebern Schwierigkeiten, datenschutzrechtlich relevante Fallkonstellationen zu erkennen, die m{\"o}glichen Risiken daraus abzuleiten und, sofern dies gelingt, diesen Risiken angemessen zu begegnen. Der vorliegende Beitrag befasst sich mit der datenschutzrechtlichen Verantwortlichkeit, ihren Folgen und den daraus resultierenden Konsequenzen f{\"u}r die Gestaltung von Vergabeverfahren und Vergabeunterlagen.}, language = {de} } @masterthesis{Gros2024, type = {Bachelor Thesis}, author = {Gros, Isabella}, title = {Depressed Furniture : eine abstrakte {\"U}bersetzung von Depressionen in M{\"o}blierung}, publisher = {FH Aachen}, address = {Aachen}, school = {Fachhochschule Aachen}, pages = {367 Seiten}, year = {2024}, abstract = {Depressed Furniture ist eine abstrakte {\"U}bersetzung von Depressionen in M{\"o}blierung. Es handelt sich um eine Rauminstallation von f{\"u}nf Leuchten, die der Erkrankung in einem un{\"u}blichen Kontext eine Plattform gibt. Dadurch stellt das Projekt eine Schnittstelle zwischen Kunst, Design und Gesellschaft dar. Jede Leuchte verk{\"o}rpert eine Empfindung, mit der sich ein Großteil der Betroffenen identifizieren kann. Es wird Bewusstsein f{\"u}r die Komplexit{\"a}t der Krankheit geschaffen und das Tabu um mentale Krankheiten gebrochen. Neben der Regular Collection k{\"o}nnen auch Tischvarianten (Compact Collection) erworben werden. Depressed Furniture zeigt, dass es durchaus m{\"o}glich ist, eine unsch{\"o}ne Thematik zu abstrahieren und ihr neutral zu begegnen. Es verdeutlicht, wie Design dazu beitragen kann, sensible Themen auf kreative Weise zu kommunizieren.}, language = {de} } @masterthesis{Giernich2024, type = {Bachelor Thesis}, author = {Giernich, Marie}, title = {Zookunft: Zoo der Zukunft}, publisher = {FH Aachen}, address = {Aachen}, pages = {93 Seiten}, year = {2024}, abstract = {Inmitten globaler Natur- und Artenschutzherausforderungen ist die Transformation zoologischer Einrichtungen entscheidend. "Zookunft" pr{\"a}sentiert ein innovatives Konzept f{\"u}r ein Tropenhaus im K{\"o}lner Zoo, das Natur und Augmented Reality einzigartig verkn{\"u}pft. Ziel ist ein Raumkonzept, welches den Besucher:innen ein tiefes Verst{\"a}ndnis f{\"u}r die Fauna und Flora des s{\"u}dostasiatischen Regenwaldes vermitteln soll. Durch die geschickte Integration von Augmented Reality entsteht eine innovative Lern- und Erlebniswelt, die Umweltschutz- und Artenschutzbem{\"u}hungen unterst{\"u}tzt und nachhaltige Bildung f{\"o}rdert. Besuchende tauchen aktiv in die faszinierende Welt des Regenwaldes ein, wenn Natur und Augmented Reality eine immersive Umgebung schaffen. "Zookunft" soll als Vorreiter f{\"u}r Zooumgestaltungen dienen, Mensch und Natur verbinden und nachhaltige Bildung f{\"o}rdern. Ein Raum, der Naturerlebnisse und Technologie beeindruckend kombiniert.}, language = {de} } @masterthesis{Fohrer2024, type = {Bachelor Thesis}, author = {Fohrer, Emil}, title = {ARCHER : become the Arrow}, publisher = {FH Aachen}, address = {Aachen}, pages = {169 Seiten}, year = {2024}, abstract = {„Archer" ist ein Redesign des Freischwingers. Ein klassischer Freischwinger ist ein aus Rohr gebogener Stuhl ohne Hinterbeine. Das Konzept des Freischwingers macht sich die Elastizit{\"a}t des Stahlrohrs zunutze, um einen schwingenden Sitz zu produzieren. An dieses Konzept kn{\"u}pft „Archer" herstellungstechnisch an, erg{\"a}nzt jedoch ein paar Features. Der erste „USP" ist die R{\"u}ckenlehne, welche aus Nylonschnur gewoben ist. Die Lehne rahmt mehrdimensional eine Sattelfl{\"a}che ein, die sich {\"u}berraschend ergonomisch dem R{\"u}cken anpasst. Sie w{\"a}chst aus den Armlehnen von vorne hinter dem R{\"u}cken zusammen. Eine weitere Neuheit sind die Hinterbeine des Stuhls. Der Schwung soll nicht weg, sondern hin zu dem, was was vor den Nutzenden liegt. In Kombination mit der Lehne, die aus den Armlehnen w{\"a}chst und hinter dem R{\"u}cken schließt, ist das Gewicht {\"u}ber den Beinen gut ausbalanciert. In seinem Aufbau vereint Er ein reduziertes klares Stahlgestell mit dramatisch gewobener Schnur. Die zwei sichtbaren Materialien im Spiel miteinander werden optisch nur noch erg{\"a}nzt von einem aus Kupfer, Messing oder Edelstahl gedrehten Stopfen mit konischem InLay. Der v{\"o}llig eigene Aufbau mit Hinterbeinen und Armlehnen erlaubt federleichtes Schwingen, einfaches Aufstehen, neutralisiert Nervosit{\"a}t und f{\"a}ngt den Nutzer / die Nutzerin sanft auf. Die ineinander verwobenen Schn{\"u}re teilen das Gewicht gleichm{\"a}ßig unter sich auf. Industrielle Herstellungsmethoden in Kombination mit Handarbeit machen diesen Stuhl zu etwas besonderem und da dem Konzept farblich kein Ende gesetzt ist, hat jeder Stuhl das Potenzial, zu einem unverkennbaren Einzelst{\"u}ck zu werden.}, language = {de} } @masterthesis{Ernsing2024, type = {Bachelor Thesis}, author = {Ernsing, Johanna}, title = {Kalle : der mitwachsende Kindertisch}, publisher = {FH Aachen}, address = {Aachen}, pages = {97 Seiten}, year = {2024}, abstract = {KALLE ist ein mitwachsender Kindertisch, dessen Besonderheit, neben der H{\"o}henverstellung, in der Vergr{\"o}ßerung der Tischplatte liegt. Hierdurch kann KALLE optimal an das Wachstum der Kinder und die sich {\"a}ndernden Anforderungen angepasst werden. Es ist ein M{\"o}belst{\"u}ck, das die Entwicklung der Kinder begleitet und f{\"o}rdert. Im Gebrauch bezieht sich die F{\"o}rderung besonders auf die kognitive Entwicklung, die Kreativit{\"a}t und das Sozialverhalten. Dar{\"u}ber hinaus sollen die Kinder mit KALLE aber auch den Umgang mit langlebigen Produkten erlernen, damit sie ein Verst{\"a}ndnis f{\"u}r Nachhaltigkeit und ein umweltbewusstes Konsumverhalten entwickeln.}, language = {de} } @masterthesis{Bunar2024, type = {Bachelor Thesis}, author = {Bunar, Moritz}, title = {Land Rover Symbiosis : Seegras erforschen und erleben}, publisher = {FH Aachen}, address = {Aachen}, pages = {149 Seiten}, year = {2024}, abstract = {Seegras wird als „Rohstoff der Zukunft" betitelt, da es helfen k{\"o}nnte, eine Reihe von globalen Problemen zu bek{\"a}mpfen. Viele der erhofften Innovationen sind heute aber noch hypothetisch. Außerdem ist das Thema in der westlichen Welt trotz der Neigung zum Klimaschutz kaum bekannt. Die Idee von „Land Rover Symbiosis" ist ein nachhaltiges Tourismuskonzept, das Forschung und Erlebnisreisen miteinander verkn{\"u}pft. Auf einer 70m Katamaran Superyacht ist Platz f{\"u}r Forschungszwecke auf der einen und Raum f{\"u}r Expeditionsurlaub auf der anderen Seite. So entsteht ein Verh{\"a}ltnis an Bord, bei dem beide Parteien voneinander profitieren: Wissenschaftler:innen erhalten finanzielle Unterst{\"u}tzung und Kund:innen haben ein klimaneutrales Urlaubserlebnis, bei dem sie hautnah die Vorz{\"u}ge und Potenziale von Seegras kennenlernen.}, language = {de} } @masterthesis{Brauweiler2024, type = {Bachelor Thesis}, author = {Brauweiler, Philipp}, title = {incontrare : Gestaltung eines Meeting Raumes durch Konzeptm{\"o}bel}, publisher = {FH Aachen}, address = {Aachen}, pages = {123 Seiten}, year = {2024}, abstract = {Incontrare, was {\"u}bersetzt Begegnung bedeutet, ist ein Konferenztischkonzept, der durch seinen modularen Aufbau heraus sticht. Dem Kunden ist es m{\"o}glich das Produkt mit einem einzigen Werkzeug - f{\"u}nfer Imbusschl{\"u}ssel - aufzubauen. Der modulare Aufbau bietet die M{\"o}glichkeit kundenorientiert ein Produkt zusammensetzen zu k{\"o}nnen. Incontrare bietet hierdurch eine Vielzahl an Variationen, die nicht nur die gestalterischen Aspekte anspricht, sondern auch verschiedene Preisklassen abdeckt. Incontrare ist ein Tischkonzept, das sowohl im niederpreisigen , sowie auch im HighEnd Bereich funktioniert.}, language = {de} } @masterthesis{Bartz2024, type = {Bachelor Thesis}, author = {Bartz, Markus}, title = {Dupiano : Ein aus einem Bauelement auffaltbarer Keyboradst{\"a}nder mit dem Erscheinungsbild eines akustischen Klavieres.}, publisher = {FH Aachen}, address = {Aachen}, pages = {123 Seiten}, year = {2024}, abstract = {Klavierspielende K{\"u}nstlerinnen und K{\"u}nstler finden sich auf der B{\"u}hne meist an einer Kombination aus Keyboard und Keyboardst{\"a}nder wieder. Zwar kann der Klang eines Klaviers technisch brillant simuliert werden, jedoch verliert das B{\"u}hnenbild den Mehrwert eines traditionellen Klaviers. Um diesem Verlust von Authentizit{\"a}t und Wohlgef{\"u}hl auf der B{\"u}hne endlich etwas entgegenzusetzen, soll ein "dupiano" g{\"a}ngige Keyboardst{\"a}nder ersetzen und s{\"a}mtliche Keyboards in das Erscheinungsbild eines akustischen Klaviers h{\"u}llen. Dadurch sollen auch die visuellen Eindr{\"u}cke, verkn{\"u}pft mit den akustischen, an Authentizit{\"a}t gewinnen und den Klavierauftritt vervollst{\"a}ndigen. Es ist leicht, stabil und ohne Werkzeug in unter 10 Sekunden aufbaubar. Auch der Abbau geschieht in unter 10 Sekunden. Verstaut werden kann es von einer Person in jedem Kofferraum. "dupiano" - was nach Klavier klingt, soll auch so aussehen!}, language = {de} } @masterthesis{Ackermann2024, type = {Bachelor Thesis}, author = {Ackermann, Vincent}, title = {Filos : Design eines Front-Ends f{\"u}r das robotergef{\"u}hrte Laser-Osteotom-System STELLA.}, publisher = {FH Aachen}, address = {Aachen}, pages = {70 Seiten}, year = {2024}, abstract = {In der Abschlussarbeit „FILOS" wurde in Zusammenarbeit mit dem Fraunhofer-Institut f{\"u}r Lasertechnik (ILT) ein Front-End f{\"u}r das laserbasierte Osteotom STELLA entwickelt. STELLA soll Kraniotomie (das Er{\"o}ffnen des Sch{\"a}dels) im wachen Zustand erm{\"o}glichen und erfordert eine benutzerfreundliche Bedienungsplattform sowie ein funktionales und {\"a}sthetisches Design. Das Ziel von „FILOS" war es, ein Geh{\"a}use zu entwerfen, das den medizinischen Anforderungen entspricht, und ein Bedienkonzept zu entwickeln, dass die Akzeptanz bei Patient:innen und Anwender:innen f{\"o}rdert. Durch Expert:innen-Interviews mit Neurochirurg:innen und enge Zusammenarbeit mit dem ILT wurde ein durchdachtes Design entwickelt. Dieses soll den Anforderungen der Anwender:innen gerecht werden, das zuk{\"u}nftige Operationssystem repr{\"a}sentieren und somit einen Mehrwert in der Medizin schaffen.}, language = {de} } @misc{DieringerRenzLindeletal.2010, author = {Dieringer, Matthias A. and Renz, Wolfgang and Lindel, Tomasz and Seifert, Frank and Frauenrath, Tobias and Waiczies, Helmar and von Knobelsdorff-Brenkhoff, Florian and Santoro, Davide and Hoffmann, Werner and Ittermann, Bernd and Schulz-Menger, Jeanette and Niendorf, Thoralf}, title = {4CH TX/RX Surface Coil for 7T: Design, Optimization and Application for Cardiac Function Imaging}, series = {2010 ISMRM-ESMRMB joint annual meeting}, journal = {2010 ISMRM-ESMRMB joint annual meeting}, issn = {1545-4428}, year = {2010}, abstract = {Practical impediments of ultra high field cardiovascular MR (CVMR) can be catalogued in exacerbated magnetic field and radio frequency (RF) inhomogeneities, susceptibility and off-resonance effects, conductive and dielectric effects in tissue, and RF power deposition constraints, which all bear the potential to spoil the benefit of CVMR at 7T. Therefore, a four element cardiac transceive surface coil array was developed. Cardiac imaging provided clinically acceptable signal homogeneity with an excellent blood myocardium contrast. Subtle anatomic structures, such as pericardium, mitral and tricuspid valves and their apparatus, papillary muscles, and trabecles were accurately delineated.}, language = {en} } @misc{FrauenrathBeckerHezeletal.2010, author = {Frauenrath, Tobias and Becker, Meike and Hezel, Fabian and Krombach, Gabriele A. and Kremer, Ute and Schulz-Menger, Jeanette and Niendorf, Thoralf}, title = {Comparison of Left Function Assessment Using Phonocardiogram and Electrocardiogram Triggered 2D SSFP CINE MR Imaging at 1.5 T and 3.0 T}, series = {2010 ISMRM-ESMRMB joint annual meeting}, journal = {2010 ISMRM-ESMRMB joint annual meeting}, issn = {1545-4428}, year = {2010}, abstract = {As high-field cardiac MRI (CMR) becomes more widespread the propensity of ECG to distortions and mistriggering increases and with it the motivation for a cardiac triggering alternative. Hence, this study explores the suitability of acoustic cardiac triggering (ACT) for left ventricular (LV) function assessment in healthy subjects at 1.5T and 3.0T.}, language = {en} } @misc{HezelFrauenrathRenzetal.2010, author = {Hezel, Fabian and Frauenrath, Tobias and Renz, Wolfgang and Schulz-Menger, Jeanette and Niendorf, Thoralf}, title = {Feasibility of CINE Myocardial T2* Mapping Using Susceptibility Weighted Gradient-Echo Imaging at 7.0 T}, series = {2010 ISMRM-ESMRMB joint annual meeting}, journal = {2010 ISMRM-ESMRMB joint annual meeting}, issn = {1545-4428}, year = {2010}, abstract = {This study is designed to demonstrate the promise of susceptibility weighted 2D CINE FLASH and T2* Mapping of the heart at 7T.}, language = {en} } @misc{FrauenrathRenzRiegeretal.2010, author = {Frauenrath, Tobias and Renz, Wolfgang and Rieger, Jan and G{\"o}mmel, Andreas and Butenweg, Christoph and Niendorf, Thoralf}, title = {High Spatial Resolution 3D MRI of the Larynx Using a Dedicated TX/RX Phased Array Coil at 7.0T}, series = {2010 ISMRM-ESMRMB joint annual meeting}, journal = {2010 ISMRM-ESMRMB joint annual meeting}, issn = {1545-4428}, year = {2010}, abstract = {MRI holds great potential for elucidating laryngeal and vocal fold anatomy together with the assessment of physiological processes associated in human phonation. However, MRI of human phonation remains very challenging due to the small size of the targeted structures, interfering signal from fat, air between the vocal folds and surrounding muscles and physiological motion. These anatomical/physiological constraints translate into stringent technical requirements in balancing, scan time, image contrast, immunity to physiological motion, temporal resolution and spatial resolution. Motivated by these challenges and limitations this study is aiming at translating the sensitivity gain at ultra-high magnetic fields for enhanced high spatial resolution 3D imaging of the larynx and vocal tract. To approach this goal a dedicated two channel TX/RX larynx coil is being proposed.}, language = {en} } @misc{MartinFrauenrathZerdemetal.2011, author = {Martin, Conrad Steven and Frauenrath, Tobias and Zerdem, Celal and Renz, Wolfgang and Niendorf, Thoralf}, title = {Evaluation of Magneto Alert Sensor (MALSE) to Improve MR Safety by Decreasing the Incidence of Ferromagnetic Projectile Accidents}, series = {2011 ISMRM Annual Meeting Proceedings}, journal = {2011 ISMRM Annual Meeting Proceedings}, issn = {1545-4428}, year = {2011}, abstract = {The magnetic forces of fringe magnetic fields of MR systems on ferromagnetic components can impose a severe patient, occupational health and safety hazard. MRI accidents are listed as number 9 of the top 10 risks in modern medicine. With the advent of ultrahigh field MR systems including passively shielded magnet versions, this risk, commonly known as the missile or projectile effect is even more pronounced. A strategy employing magnetic field sensors which can be attached to ferromagnetic objects that are commonly used in a clinical environment is conceptually appealing for the pursuit of reducing the risk of ferromagnetic projectile accidents.}, language = {en} } @misc{FrauenrathdeGeyerd'OrthNiendorf2011, author = {Frauenrath, Tobias and de Geyer d'Orth, Thibaut and Niendorf, Thoralf}, title = {Assessment of Accuracy \& Reproducibility of ECG, Pulse Oximetry \& Phonocardiogram Gating of Cardiac MRI at 7T}, series = {2011 ISMRM Annual Meeting Proceedings}, journal = {2011 ISMRM Annual Meeting Proceedings}, issn = {1545-4428}, year = {2011}, abstract = {At (ultra)high magnetic fields the artifact sensitivity of ECG recordings increases. This bears the risk of R-wave mis-registration which has been consistently reported for ECG triggered CMR at 7.0T. Realizing the constraints of conventional ECG, acoustic cardiac triggering (ACT) has been proposed. The clinical ACT has not been carefully examined yet. For this reason, this work scrutinizes the suitability, accuracy and reproducibility of ACT for CMR at 7.0T. For this purpose, the trigger reliability and trigger detection variance are examined together with an qualitative and quantitative assessment of image quality of the heart at 7.0T.}, language = {en} } @misc{FrauenrathDieringerPateletal.2011, author = {Frauenrath, Tobias and Dieringer, Matthias and Patel, Nishant and Zerdem, Celal and Hentschel, Jan and Renz, Wolfgang and Niendorf, Thoralf}, title = {From Artifact to Merit: Cardiac Gated MRI at 7T \& 3T using Magneto-Hydrodynamic Effects for Synchronization}, series = {2011 ISMRM Annual Meeting Proceedings}, journal = {2011 ISMRM Annual Meeting Proceedings}, issn = {1545-4428}, year = {2011}, abstract = {ECG is corrupted by magneto-hydrodynamic effects at higher magnetic field strength. Artifacts in the ECG trace and severe T-wave elevation might be mis-interpreted as R-waves. MHD being inherently sensitive to blood flow and blood velocity provides an alternative approach for cardiac gating, even in peripheral target areas far away from the commonly used upper torso positions of ECG electrodes. This feature would be very beneficial to address traveling time induced motion artifacts and trigger latency related issues raised by ECG-gated peripheral MR angiography. For all those reasons, this work proposes the use of MHD-trigger for cardiac gated MR.}, language = {en} } @misc{HeringUlberTippkoetter2016, author = {Hering, T. and Ulber, Roland and Tippk{\"o}tter, Nils}, title = {Antimikrobielle Oberfl{\"a}chenmodifikation durch Mikropartikel}, series = {Chemie Ingenieur Technik}, volume = {88}, journal = {Chemie Ingenieur Technik}, number = {9}, publisher = {Wiley-VCH}, address = {Weinheim}, doi = {10.1002/cite.201650084}, pages = {1302}, year = {2016}, abstract = {Die Ausbildung von Biofilmen in technischen Anlagen, wie z. B. K{\"u}hlkreisl{\"a}ufen, Wasseraufbereitungssystemen und Bioreaktoren, f{\"u}hren zu Materialsch{\"a}den (Biofouling) und stark erh{\"o}htem Energieaufwand. Im Rahmen der aktuellen Forschungsarbeiten erfolgen aktive sowie passive Bio-Modifikationen auf funktionalisierten magnetischen Mikropartikelober-fl{\"a}chen. Um die verschiedenen funktionalisierten magnetischen Mikropartikel zu analysieren und ihre antimikrobielle Wirkung zu testen, wird der Einsatz einer 3D-gedruckten, magnetischen Plattform f{\"u}r ein Fluoreszenz-basiertes Screening-System untersucht. F{\"u}r den Oberfl{\"a}chenschutz wurden verschiedene, antimikrobiell funktionalisierte Partikelkombinationen mit dem Mikroorganismus Escherichia coli GFPmut2 in Bezug auf aktiven Oberfl{\"a}chenschutz verglichen. Um die antimikrobielle Oberfl{\"a}cheneffekte von synergistischen Kombinationen unterschiedlich funktionalisierter Partikel zu bestimmen, werden Oberfl{\"a}chen einem Magnetfeld ausgesetzt, das die Mikropartikel als definierte Schicht auf ihnen zur{\"u}ck h{\"a}lt. Diese modifizierten Oberfl{\"a}chen k{\"o}nnen sowohl durch Fluoreszenzspektroskopie als auch -mikroskopie analysiert werden.}, language = {de} } @misc{KuthanAlKaidyTippkoetter2016, author = {Kuthan, K. and Al-Kaidy, H. and Tippk{\"o}tter, Nils}, title = {Tropfenbasierte Enzymreaktionen auf Glasoberfl{\"a}chen im μL-Maßstab mit ortsaufgel{\"o}ster pL-Dosierung der Reaktanden}, series = {Chemie Ingenieur Technik}, volume = {88}, journal = {Chemie Ingenieur Technik}, number = {9}, publisher = {Wiley-VCH}, address = {Weinheim}, doi = {10.1002/cite.201650117}, pages = {1336 -- 1337}, year = {2016}, abstract = {Mit der Entwicklung w{\"a}ssriger Tropfen, die mit einer sch{\"u}tzenden H{\"u}lle magnetisierbarer, hydrophober Partikel umgeben sind, ergeben sich neue M{\"o}glichkeiten im Bereich der Mikrofluidik. So k{\"o}nnen die Tropfen als fl{\"u}ssige Mikroreaktoren eingesetzt werden. Der w{\"a}ssrige Kern dieser Mikroreaktoren besteht aus einer Substratl{\"o}sung f{\"u}r enzymatische Umsetzungen. Durch Bewegen der Mikroreaktoren k{\"o}nnen diese {\"u}ber immobilisierten Enzymen positioniert werden, um so einen enzymatischen Umsatz innerhalb der Mikroreaktoren zu realisieren. Hierf{\"u}r wurde eine neue Mikroreaktorplattform-Technologie etabliert. Die Mikroreaktoren k{\"o}nnen aufgrund ihrer magnetisierbaren H{\"u}llenpartikel {\"u}ber elektromagnetische Spulen bewegt werden. Die Bewegung erfolgt dabei mit einer automatisierten Aktuatorplattform, bestehend aus einer 3x3 Doppelspulenmatrix mit Magnetkernen. Als modellhaftes Reaktionssystem wird eine Enzymkaskade eingesetzt, die sich aus einer b-Glucosidase, Glucose-Oxidase und Meerrettichperoxidase zusammensetzt. Prim{\"a}r untersuchte Substrate sind Fluorescein-di-b-D-glucopyranoside, und 1-(3,7-Dihydroxy-10H-phenoxazin-10-yl)-ethanon, bei deren Umsatz fluoreszierende Produkte entstehen.}, language = {de} } @article{AliaziziOezsoyluBakhshiSichanietal.2024, author = {Aliazizi, Fereshteh and {\"O}zsoylu, Dua and Bakhshi Sichani, Soroush and Khorshid, Mehran and Glorieux, Christ and Robbens, Johan and Sch{\"o}ning, Michael J. and Wagner, Patrick}, title = {Development and Calibration of a Microfluidic, Chip-Based Sensor System for Monitoring the Physical Properties of Water Samples in Aquacultures}, series = {Micromachines}, volume = {15}, journal = {Micromachines}, number = {6}, publisher = {MDPI}, address = {Basel}, issn = {2072-666X}, doi = {10.3390/mi15060755}, year = {2024}, abstract = {In this work, we present a compact, bifunctional chip-based sensor setup that measures the temperature and electrical conductivity of water samples, including specimens from rivers and channels, aquaculture, and the Atlantic Ocean. For conductivity measurements, we utilize the impedance amplitude recorded via interdigitated electrode structures at a single triggering frequency. The results are well in line with data obtained using a calibrated reference instrument. The new setup holds for conductivity values spanning almost two orders of magnitude (river versus ocean water) without the need for equivalent circuit modelling. Temperature measurements were performed in four-point geometry with an on-chip platinum RTD (resistance temperature detector) in the temperature range between 2 °C and 40 °C, showing no hysteresis effects between warming and cooling cycles. Although the meander was not shielded against the liquid, the temperature calibration provided equivalent results to low conductive Milli-Q and highly conductive ocean water. The sensor is therefore suitable for inline and online monitoring purposes in recirculating aquaculture systems.}, language = {en} } @incollection{Fissabre2024, author = {Fissabre, Anke}, title = {Eine moderne Sainte-Chapelle in K{\"o}ln. Otto Bartnings Stahlkirche auf der Pressa 1928}, series = {Baugedanken: Einsichten, Ansichten, Aussichten f{\"u}r Jan Pieper zum 80. Geburtstag}, booktitle = {Baugedanken: Einsichten, Ansichten, Aussichten f{\"u}r Jan Pieper zum 80. Geburtstag}, editor = {Naujokat, Anke and Hake, Verena and Schindler, Bruno and Sch{\"o}tten, Bj{\"o}rn}, publisher = {Geym{\"u}ller Verag f{\"u}r Architektur}, address = {Aachen}, isbn = {978-3-943164-87-9}, pages = {66 -- 81}, year = {2024}, language = {de} } @misc{RothTippkoetter2016, author = {Roth, J. and Tippk{\"o}tter, Nils}, title = {New Approach for Enzymatic Hydrolysis of Lignocellulose with Selective Diffusion Separation of the Monosaccharide Products}, series = {Chemie Ingenieur Technik}, volume = {88}, journal = {Chemie Ingenieur Technik}, number = {9}, publisher = {Wiley-VCH}, address = {Weinheim}, issn = {0009-286X}, doi = {10.1002/cite.201650301}, pages = {1237}, year = {2016}, abstract = {Enzymatic hydrolysis of lignocellulosic material plays an important role in the classical biorefinery approach. Apart from the pretreatment of the raw material, hydrolysis is the basis for the conversion of the cellulose and hemicellulose fraction into fermentable sugars. After hydrolysis, usually a solid-liquid separation takes place, in order to separate the residual plant material from the sugar-rich fraction, which can be subsequently used in a fermentation step. In order to factor out the separation step, the usage of in alginate immobilized crude cellulose fiber beads (CFBs) were evaluated. Pretreated cellulose fibers are incorporated in an alginate matrix together with the relevant enzymes. In doing so, sugars diffuse trough the alginate matrix, allowing a simplified delivery into the surrounding fluid. This again reduces product inhibition of the glucose on the enzyme catalysts. By means of standardized bead production the hydrolysis in lab scale was possible. First results show that liberation of glucose and xylose is possible, allowing a maximum total sugar yield of 75 \%.}, language = {en} } @misc{WulfhorstMerseburgTippkoetter2016, author = {Wulfhorst, H. and Merseburg, J. and Tippk{\"o}tter, Nils}, title = {Batteriekomponenten aus nachwachsenden Rohstoffen}, series = {Chemie Ingenieur Technik}, volume = {88}, journal = {Chemie Ingenieur Technik}, number = {9}, publisher = {Wiley-VCH}, address = {Weinheim}, issn = {0009-286X}, doi = {10.1002/cite.201650333}, pages = {1234 -- 1235}, year = {2016}, abstract = {In diesem Beitrag geht es um die Integration von Stoffstr{\"o}men einer Lignocellulose-Bioraffinerie in Verfahren zur Batterieherstellung. Pflanzliche Reststoffe aus der Biokraftstoffherstellung wie Lignin sollen zur Herstellung neuer Batteriematerialien verwendet werden. Hierbei wird das Lignin als Matrix f{\"u}r die vorgraphitischen C-haltigen Einlagerungsverbindungen in den Elektroden genutzt. Die Si-C-Komposite werden durch das Einbetten von Si in eine Ligninmatrix mit anschließender Carbonisierung hergestellt. Das Lignin hierf{\"u}r wird durch die sequentielle hydrothermale Vorbehandlung von Buchenholz bei variablen Bedingungen gewonnen und mit Si-Nanopartikel sowie als Referenz ohne Si-Nanopartikel gef{\"a}llt. Die Ergebnisse zeigen, dass die sequenzielle Vorbehandlung h{\"o}here Ausbeuten im Vergleich zum LHW- oder Organosolv-Aufschluss liefert. Um eine Anode herzustellen, wurde das resultierende Si-C-Kompositmaterial carbonisiert, auf einen Stromsammler aufgetragen und elektro-chemisch charakterisiert. Der Einfluss der Vorbehandlungsschritte auf den Herstellungsprozess und die {\"o}konomische Bewertung des untersuchten Bioraffinerie-Prozesses wurde mithilfe eines Stoffstrommodells analysiert.}, language = {de} } @misc{PothMonzonTippkoetteretal.2010, author = {Poth, S. and Monzon, M. and Tippk{\"o}tter, Nils and Ulber, Roland}, title = {Lignocellulose-Bioraffinerie: Simultane Verzuckerung und Fermentation}, series = {Chemie Ingenieur Technik}, volume = {82}, journal = {Chemie Ingenieur Technik}, number = {9}, publisher = {Wiley-VCH}, address = {Weinheim}, doi = {10.1002/cite.201050360}, pages = {1568}, year = {2010}, abstract = {Die am h{\"a}ufigsten genutzten Rohstoffe f{\"u}r die Produktion von Treibstoffen und Chemikalien sind fossilen Ursprungs. Da diese limitiert sind, werden im Hinblick auf die Nachhaltigkeit alternative, erneuerbare Rohstoffquellen intensiv untersucht. Vielversprechend in diesem Kontext sind die in Lignocellulose enthaltenen Zucker, die beispielsweise zur Produktion von Ethanol genutzt werden k{\"o}nnen. In der Regel sind f{\"u}r eine Lig-nocellulose-Bioraffinerie mehrere Prozessschritte notwendig: Vorbehandlung, Verzuckerung und Fermentation. Um diesen Prozess einfacher zu gestalten, ist es m{\"o}glich, die Verzuckerung und die Fermentation in einem Schritt durchzuf{\"u}hren (SSF). Als Substrat wird hier Cellulose-Faserstoff verwendet, der durch das Organosolv-Verfahren aufgeschlossen wurde. Die Hydrolyse erfolgt mit kommerziell erh{\"a}ltlichen Enzymen und f{\"u}r die Fermentation zu Ethanol werden zwei Hefen verwendet. Beim SSF-Verfahren konnte, im Vergleich zur entkoppelten Verfahrensweise, trotz bestehender Unterschiede in den Temperatur-Optima von Enzymen und Hefen eine Steigerung in der Ethanol-Ausbeute von 0,15 auf 0,2 gg⁻¹ beobachtet werden. Um wirtschaftliche Ausbeuten und Konzentrationen des Produkts erzielen zu k{\"o}nnen, ist es notwendig den Prozess weiter zu optimieren. Im Einzelfall muss {\"u}berpr{\"u}ft werden, ob diese Verfahrensweise auch f{\"u}r die Produktion anderer interessanter Stoffe (wie Itacons{\"a}ure, Bernsteins{\"a}ure) geeignet ist.}, language = {de} } @misc{PasteurLudwigTippkoetteretal.2010, author = {Pasteur, A. and Ludwig, B. and Tippk{\"o}tter, Nils and Diller, R. and Kampeis, P. and Ulber, Roland}, title = {Aufarbeitung von β-Lactamantibiotika mittels selektiver, magnetischer Adsorbermaterialien}, series = {Chemie Ingenieur Technik}, volume = {82}, journal = {Chemie Ingenieur Technik}, number = {9}, publisher = {Wiley-VCH}, address = {Weinheim}, doi = {10.1002/cite.201050270}, pages = {1587}, year = {2010}, abstract = {b-Lactame geh{\"o}ren zu den wirkungsvollsten Antibiotika, jedoch lassen sich viele nur schwierig fermentativ erzeugen. Ein Problem bei der fermentativen Produktion ist die Hydrolyse des Lactamrings im w{\"a}ssrigen Milieu. Das Ziel des von der DBU gef{\"o}rderten Projekts ist die selektive In-situ-Adsorption der b-Lactamantibiotika unter anschließender magnetischer Separation. Durch die Isolation im Hochgradientenmagnetseparator (HGMS) ist eine Fest-fest-fl{\"u}ssig-Trennung und somit ein erheblicher Zeitgewinn im Downstreamprozess m{\"o}glich. Zus{\"a}tzlich kommt es zur Einsparung an L{\"o}sungsmittel und Energie, was neben Reduzierung der Antibiotikahydrolyse auch in {\"o}kologischer Hinsicht einen interessanten Aspekt darstellt. Als Tr{\"a}germaterial f{\"u}r die Adsorbermatrix werden magnetisierbare Eisenoxidpartikel eingesetzt, die in einer Silikamatrix eingebettet sind. Diese Adsorber sollen auf Selektivit{\"a}t in Wasser und verschiedenen Medien getestet werden. Zus{\"a}tzlich werden die Abbauprodukte des b-Lactams analysiert, um eine Aussage {\"u}ber die Stabilisierung des Antibiotikums durch die selektiven Adsorber treffen zu k{\"o}nnen. Diese Ergebnisse werden mit kommerziell erh{\"a}ltlichen Adsorbern verglichen. Die Aufreinigung der Antibiotika soll direkt aus der Fermentationsbr{\"u}he erfolgen. Um die Trennung der magnetischen, selektiven Adsorber von der Biomasse zu gew{\"a}hrleisten, soll der HGMS in die Fermentation integriert werden. Das filament{\"o}se Wachstum des Mikroorganismus erfordert eine Neuauslegung der Filtermatrix.}, language = {de} } @misc{TippkoetterZhangPothetal.2010, author = {Tippk{\"o}tter, Nils and Zhang, M. and Poth, S. and Ulber, Roland}, title = {Enzymatische Lignindegradierung unter Einsatz eines Optimierungsalgorithmus}, series = {Chemie Ingenieur Technik}, volume = {82}, journal = {Chemie Ingenieur Technik}, number = {9}, publisher = {Wiley-VCH}, address = {Weinheim}, issn = {0009-286X}, doi = {10.1002/cite.201050707}, pages = {1601 -- 1602}, year = {2010}, abstract = {Lignine bestehen aus einem hochgradig vernetzten Polymer phenolischer Grundeinheiten. Diese Verbindungen sind eine Quelle vielversprechender chemischer Grundbausteine. Auch die enzymatische Modifikation der Materialeigenschaften des Lignins ist f{\"u}r dessen Anwendung von Interesse. Aufgrund der verschiedenen Bindungstypen im Lignin ist eine Auftrennung mit nur einem Enzym unwahrscheinlich. Vielmehr sind verschiedene mediatorgest{\"u}tzte Reaktionen notwendig. Pilze, wie z.B. T. versicolor, nutzen Enzymkombinationen zum Aufschluss des Lignins. Hierbei kommen Laccase, Ligninperoxidase und Manganperoxidase zum Einsatz. Die optimale Kombination der Enzyme und ihrer Mediatoren bzw. Stabilisatoren ist Ziel der Untersuchungen. Aufgrund der großen Parameteranzahl wurde ein genetischer Algorithmus eingesetzt. Als Versuchsparameter wurden gew{\"a}hlt: die Verh{\"a}ltnisse der Enzyme, Ligninmasse, Konzentrationen an Eisen-, Mangan-, Oxalat-Ionen, ABTS, Violurs{\"a}ure und H₂O₂. Somit werden elf Parameter simultan optimiert. Als Algorithmus wurde ein Programm mit variabler Genkodierung entwickelt. Die Umsetzung des Lignins wird dabei {\"u}ber den verfolgt. Zurzeit ist ein enzymatischer Umsatz von 12\% m{\"o}glich. Als Referenz wurde eine chemische Lignindegradierung mit einem Umsatzvon 37\% etabliert. Die sechs Generationen des Algorithmus zeigen eine Kongruenz der Enzymkonzentrationen von LiP, MnP und VeP, w{\"a}hrend Laccase keinen Einfluss hat. Des Weiteren beeinflussen die Konzentrationen von Mangan und Oxalat die Umsetzung, w{\"a}hrend die Variation von ABTS- und H₂O₂ nur eine geringe Auswirkung hat.}, language = {de} } @misc{StaubTippkoetterSucketal.2010, author = {Staub, C. and Tippk{\"o}tter, Nils and Suck, K. and Sohling, U. and Ulber, Roland}, title = {Chromatographische Aufarbeitung von Molkekonzentrat mittels mineralischer Granulate}, series = {Chemie Ingenieur Technik}, volume = {82}, journal = {Chemie Ingenieur Technik}, number = {9}, publisher = {Wiley-VCH}, address = {Weinheim}, issn = {0009-286X}, doi = {10.1002/cite.201050322}, pages = {1588 -- 1589}, year = {2010}, abstract = {Molke f{\"a}llt im Rahmen der K{\"a}seherstellung allein in Deutschland in Mengen von {\"u}ber 11 Mio. Tonnen j{\"a}hrlich an. Dieses Nebenprodukt wurde trotz seines Reichtums an Milchzucker und Proteinen lange Zeit kaum industriell weiterverarbeitet und stellte ein bedeutendes Problem bei der Abwasserreinigung dar. Derzeit kommen meist kosten- und reinigungsintensive Membranfiltrationsverfahren bei der Auftrennung von Molke in ihre Hauptkomponenten Lactose und Molkenprotein zum Einsatz. Die Produkte finden vorwiegend in der Nahrungsmittelindustrie Anwendung als S{\"u}ßungsmittel, Proteinzusatz oder Texturbildner. Die Mehrheit des Proteins wird dabei als Konzentrat bzw. Proteinpulver verarbeitet. Wegen der antibakteriellen, antiviralen und weiteren wertvollen physiologischen Eigenschaften der Molkeproteine stellt eine weitere Aufreinigung der einzelnen Molkeproteine f{\"u}r die pharmazeutische Industrie einen naheliegenden zus{\"a}tzlichen Wertsch{\"o}pfungsschritt dar. In Kooperation mit der S{\"u}d Chemie AG wurde damit begonnen, ein Verfahren zu entwickeln, das kosteng{\"u}nstige mineralische Adsorbentien verwendet. Bisher konnte die Abtrennung von Lactose von den Molkenproteinen aus verd{\"u}nntem Molkekonzentrat in einem Verfahrensschritt ohne Vorbehandlung des Rohstoffs erfolgreich realisiert werden. Aktuelle Arbeiten besch{\"a}ftigen sich mit der Verbesserung der Proteinbindekapazit{\"a}tund chromatographischen Proteinauftrennung sowie dem Upscaling zum direkten Einsatz von Molkekonzentrat ohne Vorverd{\"u}nnung.}, language = {de} } @misc{StaubTippkoetterSucketal.2009, author = {Staub, C. and Tippk{\"o}tter, Nils and Suck, K. and Ruf, F. and Sohling, U. and Ulber, Roland}, title = {Aufreinigung von Molkeproteinen mittels nat{\"u}rlicher Adsorbermaterialien}, series = {Chemie Ingenieur Technik}, volume = {81}, journal = {Chemie Ingenieur Technik}, number = {8}, publisher = {Wiley-VCH}, address = {Weinheim}, issn = {0009-286X}, doi = {10.1002/cite.200950310}, pages = {1299}, year = {2009}, abstract = {Molke als Nebenprodukt der K{\"a}seherstellung wurde lange Zeit als Abfall betrachtet. Bedingt durch ihren hohen BOD (biological oxygen demand) war die direkte Einleitung in Gew{\"a}sser, aber auch der mikrobielle Abbau in Kl{\"a}ranlagen bedenklich. Falls eine Weiterverarbeitung der Molke stattfand, so geschah dies meist zu Molkepulver oder Proteinkonzentrat. Als Untersuchungen der Molkeproteine jedoch unter pharmazeutischen Gesichtspunkten interessante Eigenschaften nahelegten, stieg das Interesse am Bioprodukt Molke und ihren Proteinen an. So stehen beispielsweise f{\"u}r die Molkeproteine a-Lactalbumin (ala) und b-Lactoglobulin (blg) antibakterielle, anticancerogene und diverse andere physiologische Effekte in der Diskussion. Gegenw{\"a}rtig finden meist Membranverfahren zur Aufreinigung von Molkeproteinen Anwendung. Als alternatives Verfahren wurde am Institut f{\"u}r Bioverfahrenstechnik in Kaiserslautern ein chromatographisches Verfahren entwickelt, bei dem nat{\"u}rliche Tonminerale zum Einsatz kamen. Nach chemischer und physikalischer Modifikation des Ausgangsmaterials durch den Hersteller S{\"u}d-Chemie wurden drei der Adsorber f{\"u}r n{\"a}here Untersuchungen zur Auftrennung von Molkeproteinen aus Molkekonzentrat herangezogen. Nach einer Cross-Flow-Filtration des Molkekonzentrats erfolgte die Aufreinigung der Molkeproteine in einem FPLC-System.}, language = {de} } @misc{PothMonzonTippkoetteretal.2009, author = {Poth, S. and Monzon, M. and Tippk{\"o}tter, Nils and Ulber, Roland}, title = {Enzymatische Hydrolyse von vorbehandelter Lignocellulose}, series = {Chemie Ingenieur Technik}, volume = {81}, journal = {Chemie Ingenieur Technik}, number = {8}, publisher = {Wiley-VCH}, address = {Weinheim}, issn = {0009-286X}, doi = {10.1002/cite.200950244}, pages = {1049}, year = {2009}, abstract = {Die {\"o}konomische Abh{\"a}ngigkeit von fossilen Brennstoffen und der klimatische Wandel durch die Nutzung dieser haben zu einer intensiven Suche nach erneuerbaren Rohstoffen f{\"u}r die Produktion von Chemikalien und Treibstoffen gef{\"u}hrt. Ein viel versprechender Rohstoff in diesem Zusammenhang sind Zucker, die mittels enzymatischer Hydrolyse aus Lignocellulose gewonnen und beispielsweise zu Ethanol umgesetzt werden k{\"o}nnen. Dabei ist es notwendig die Hydrolyse in Hinsicht auf das verwendete Substrat und die Verwendung der entstehenden Hydrolysate f{\"u}r die Fermentation von Alkohol zu optimieren. Als Substrat dienen Cellulose- und Hemicellulose-Fraktionen, die durch thermo-chemische Vorbehandlung von Holz gewonnen werden. Die Vorbehandlung erfolgt bei unserem Projektpartner am Johann Heinrich von Th{\"u}nen Institut in Hamburg. Verschiedene kommerziell erh{\"a}ltliche Enzyme, thermostabile eingeschlossen, wurden auf ihre F{\"a}higkeit hin untersucht, diese Fraktionen zu den entsprechenden Zuckern umsetzen zu k{\"o}nnen. Um die Konzentration an fermentierbaren Zuckern zu steigern werden verschiedene Optimierungen durchgef{\"u}hrt, z. B. die Erh{\"o}hung der Substrat- bzw. Enzymkonzentrationen. Ein weiterer interessanter Ansatz, welcher ebenfalls verfolgt wird, ist es die Hydrolyse und die Fermentation in einem Schritt durchzuf{\"u}hren.}, language = {de} } @misc{TippkoetterWiesenThieletal.2014, author = {Tippk{\"o}tter, Nils and Wiesen, S. and Thiel, A. and Muffler, K. and Ulber, Roland}, title = {Biotechnologische Wertstoffgewinnung entlang der Prozessketten Gr{\"u}ner und Pflanzen{\"o}l-Bioraffinerien}, series = {Chemie Ingenieur Technik}, volume = {86}, journal = {Chemie Ingenieur Technik}, number = {9}, publisher = {Wiley-VCH}, address = {Weinheim}, issn = {0009-286X}, doi = {10.1002/cite.201450283}, pages = {1605}, year = {2014}, abstract = {Der nachwachsende Rohstoff Raps ist in großen Mengen verf{\"u}gbar und eine Quelle f{\"u}r Biomolek{\"u}le mit hohem Wertsch{\"o}pfungspotenzial. Entwicklungen zur biotechnologischen Wertstoffgewinnung werden dabei schwerpunktm{\"a}ßig in den Bereichen Aufarbeitung und Funktionalisierung von Polyphenolen und Fetten betrieben. Bei der Verarbeitung der Pflanzenmaterialien werden dabei insbesondere Verfahren zur adsorptiven Aufreinigung und Auftrennung mittels Materialien mit modifizierten Bleicherden und anderen organischen oder anorganischen Adsorbentien untersucht. Ferner wurden f{\"u}r die Aufreinigung von Polyphenolen adsorptive sowie extraktive Prozesse entwickelt. Bei den Entwicklungen wird ber{\"u}cksichtigt, dass Bioraffinerien auf eine fortw{\"a}hrende Gew{\"a}hrleistung eines hohen Produktions- bzw. Lieferbedarfs nachwachsender Rohstoffe angewiesen sind. Somit werden Optionen dezentraler regionaler Vorbehandlungs- und Wertsch{\"o}pfungsketten in der N{\"a}he landwirtschaftlicher Betriebe einbezogen. Neben neuen Aufreinigungsverfahren werden mikrobielle und enzymatische Prozesse zur wertsteigernden Umsetzung von Glycerin, Polyphenolen und Zuckermonomeren vorgestellt sowie Limitierungen nachwachsender Rohstoffe der 2. Generation diskutiert.}, language = {de} } @misc{WollnyAlKaidyTippkoetteretal.2014, author = {Wollny, S. and Al-Kaidy, H. and Tippk{\"o}tter, Nils and Ulber, Roland}, title = {Prozessintegrierte Magnetseparation im Labormaßstab mittels High-Gradient Magnetic Separator (HGMS)}, series = {Chemie Ingenieur Technik}, volume = {86}, journal = {Chemie Ingenieur Technik}, number = {9}, publisher = {Wiley-VCH}, address = {Weinheim}, issn = {0009-286X}, doi = {10.1002/cite.201450618}, pages = {1507}, year = {2014}, abstract = {Die Hochgradient-Magnetseparation (HGMS) stellt eine Alternative zu konventionellen Methoden der Proteinaufarbeitung wie Filtration und Chromatographie dar und dient zudem als Prozessintensivierung. Bisherige Separatoren sind f{\"u}r Anwendungen von mehreren Litern Prozessvolumina Fermentationsmedium und Gramm Magnetpartikel ausgelegt. Bei der Entwicklung und Anwendung neuartiger Magnetpartikeloberfl{\"a}chen ist die Verf{\"u}gbarkeit großer Mengen nicht gegeben. Bisherige Filterkammern erh{\"o}hen zudem den Arbeitsaufwand und verursachen gr{\"o}ßere Partikelverluste bei Sp{\"u}lvorg{\"a}ngen oder der Reinigung aufgrund der Partikeladsorption. F{\"u}r Anwendungen im Maßstab < 500 mL wird deshalb ein Miniatur-Hochgradientfilter (miniHGF) entwickelt. Das Modell wird im 3D-Drucker Makerbot Replicator 2 gefertigt und magne-isierbare Dr{\"a}hte zur Partikelabscheidung eingesetzt. Die Vergleichbarkeit mit einem etablierten Magnetseparator wird anhand der Aufnahme von Durchbruchskurven und Bestimmung der Filtereffizienz untersucht. Die Praxistauglichkeit mit kleinen Volumina wird in wiederholten Batch-Versuchen mit auf Magnetpartikeln immobilisiertem Enzym und einem kolorimetrischen Assay gepr{\"u}ft.}, language = {de} } @misc{TippkoetterDuweRaisetal.2014, author = {Tippk{\"o}tter, Nils and Duwe, Anna and Rais, Dominik and Zibek, Susanne and Zorn, H.}, title = {Optimierung und Scale-up der enzymatischen Hydrolyse inkl. Ligninabbau}, series = {Chemie Ingenieur Technik}, volume = {86}, journal = {Chemie Ingenieur Technik}, number = {9}, publisher = {Wiley-VCH}, address = {Weinheim}, issn = {0009-286X}, doi = {10.1002/cite.201450287}, pages = {1515}, year = {2014}, abstract = {Prim{\"a}re Ziele der Hydrolyse pflanzlicher nachwachsender Rohstoffe sind m{\"o}glichst hohe Zuckerkonzentrationen f{\"u}r nachfolgende Fermentationen und eine Maximierung der Produktivit{\"a}t. Zur Optimierung dieser Prozesse wird Organosolv-aufgeschlossene Buchenholz-Cellulose verwendet. Die Hydrolyse des Faserstoffes erfolgt mithilfe von Novozymes CTec2-Enzymen. Die Hydrolysen konnten durch neue R{\"u}hrerelemente auf einen Maßstab von 1000 L {\"u}bertragen werden. Dabei konnten maximale Ausbeuten (g Glucose g -1 Glucose im Faserstoff) bis 81 g g - 1 und Konzentrationen von 152 g L -1 erreicht werden. Zurzeit k{\"o}nnen unter Einsatz eines Feststoffreaktors Cellulosefasern in einer Konzentration bis 400 g L -1 enzymatisch hydrolysiert werden. Die cellulolytischen Enzyme stoßen bei hohen Feststoffkonzentrationen an ihre Grenzen. Mit steigendem Feststoffgehalt nimmt die Hydrolyseausbeute ab. Ein Ansatz zur Steigerung der Effizienz ist der Einsatz ligninolytischer Enzyme, die Ligninreste an der Organosolv-Cellulose aufschließen k{\"o}nnen. Eine solche Verbesserung der Zug{\"a}nglichkeit f{\"u}r cellulolytische Enzyme an ihr Substrat wurde durch Kultur{\"u}berst{\"a}nde verschiedener ligninolytischer Pilze erreicht. Mit Kultur{\"u}berst{\"a}nden von Stereum sp. sind Steigerungen der Glucoseausbeuten um bis zu 30 \% m{\"o}glich.}, language = {de} } @misc{HeringPasteurWollnyetal.2014, author = {Hering, T. and Pasteur, A. and Wollny, S. and Ulber, Roland and Tippk{\"o}tter, Nils}, title = {Magnetische Separation von Gold-Nanopartikeln zur Glucons{\"a}ure-Produktion durch Hochgradient-Magnetseparation im Labormaßstab}, series = {Chemie Ingenieur Technik}, volume = {86}, journal = {Chemie Ingenieur Technik}, number = {9}, publisher = {Wiley-VCH}, address = {Weinheim}, issn = {0009-286X}, doi = {10.1002/cite.201450265}, pages = {1501}, year = {2014}, abstract = {Bei der Verarbeitung nachwachsender Rohstoffe entsteht aus Cellulose oder St{\"a}rke u. a. das wichtige Produkt Glucose. Diese niedermolekulare Kohlenhydratquelle wird {\"u}blicherweise als Substrat f{\"u}r biotechnologische und chemische Synthesen verwendet. Ein wirtschaftlich interessantes Oxidationsprodukt der Glucose ist Glucons{\"a}ure, die beispielsweise als Lebensmittelzusatzstoff (E 574), in der Medizin und Metallindustrie Verwendung findet. Die Umsetzung des Monosaccharids zu Glucons{\"a}ure erfolgt entweder durch mikrobielle Fermentation oder der Oxidation an heterogenen Katalysatoren. Die Zielsetzung der Studie ist die Untersuchung der Glucoseoxidation an magnetisierbaren Gold-Nanopartikeln unter nachfolgender Bypass-Separation des Katalysators mittels einer neuen Mini-HGMS-Einheit (Hochgradient-Magnetseparation). Dieser Filtertyp erm{\"o}glicht die selektive Trennung magnetischer Partikel aus Suspensionen mit hohem Feststoffgehalt oder Viskosit{\"a}t. Erste Ergebnisse zeigen eine Beladungskapazit{\"a}t des selbstkonstruierten Mini-HGMS von 550 mg goldbeschichteter magnetisierbarer Nanopartikel. Die Oxidation erfolgt bei einem pH-Wertvon 9, bei 40 °C und mit 100 mM Glucose in einem begasten R{\"u}hrkesselreaktor. Das System soll zuk{\"u}nftig zum Katalysatorrecycling von hochviskosen und Feststoffbelasteten Produktstr{\"o}men aus Bioraffinerien eingesetzt werden.}, language = {de} }