@inproceedings{SchwarzboezlPompKolletal.2010,
  author    = {Schwarzb{\"o}zl, Peter and Pomp, Stefan and Koll, Gerrit and Hennecke, Klaus and Hartz, Thomas and Schmitz, Mark and Hoffschmidt, Bernhard},
  title     = {The solar tower J{\"u}lich - first operational experiences and test results},
  series = {SolarPACES 2010 : the CSP Conference: electricity, fuels and clean water from concentrated solar energy ; 21 to 24 September 2010, Perpignan, France},
  booktitle = {SolarPACES 2010 : the CSP Conference: electricity, fuels and clean water from concentrated solar energy ; 21 to 24 September 2010, Perpignan, France},
  publisher = {Soc. OSC},
  address   = {Saint Maur},
  pages     = {8 -- 9},
  year      = {2010},
  language  = {en}
}
@inproceedings{BuckWurmhoeringerLehleetal.2010,
  author    = {Buck, R. and Wurmh{\"o}ringer, K. and Lehle, R. and Pfahl, A. and G{\"o}ttsche, Joachim and Meyr, T.},
  title     = {Development of a 30m2 heliostat with hydraulic drive},
  series = {SolarPACES 2010 : the CSP Conference: electricity, fuels and clean water from concentrated solar energy ; 21 to 24 September 2010, Perpignan, France},
  booktitle = {SolarPACES 2010 : the CSP Conference: electricity, fuels and clean water from concentrated solar energy ; 21 to 24 September 2010, Perpignan, France},
  publisher = {Soc. OSC},
  address   = {Saint Maur},
  pages     = {74 -- 75},
  year      = {2010},
  language  = {en}
}
@inproceedings{AlexopoulosHoffschmidtRauetal.2010,
  author    = {Alexopoulos, Spiros and Hoffschmidt, Bernhard and Rau, Christoph and Schmitz, M. and Schwarzb{\"o}zl, P. and Pomp, Stefan},
  title     = {Simulation results for a hybridized operation of a gas turbine or a burner for a small solar tower power plant},
  series = {SolarPACES 2010 : the CSP Conference: electricity, fuels and clean water from concentrated solar energy ; 21 to 24 September 2010, Perpignan, France},
  booktitle = {SolarPACES 2010 : the CSP Conference: electricity, fuels and clean water from concentrated solar energy ; 21 to 24 September 2010, Perpignan, France},
  publisher = {Soc. OSC},
  address   = {Saint Maur},
  pages     = {82 -- 83},
  year      = {2010},
  language  = {en}
}
@inproceedings{BaumannTeixeiraBouraGoettscheetal.2010,
  author    = {Baumann, T. and Teixeira Boura, Cristiano Jos{\´e} and G{\"o}ttsche, Joachim and Hoffschmidt, Bernhard and O'Connell, B. and Schmitz, S. and Zunft, S.},
  title     = {Air/Sand heat exchanger design and materials for solar thermal power plant applications},
  series = {SolarPACES 2010 : the CSP Conference: electricity, fuels and clean water from concentrated solar energy ; 21 to 24 September 2010, Perpignan, France},
  booktitle = {SolarPACES 2010 : the CSP Conference: electricity, fuels and clean water from concentrated solar energy ; 21 to 24 September 2010, Perpignan, France},
  publisher = {Soc. OSC},
  address   = {Saint Maur},
  pages     = {146 -- 147},
  year      = {2010},
  language  = {en}
}
@inproceedings{FrickeHoffschmidt2010,
  author    = {Fricke, Barbara and Hoffschmidt, Bernhard},
  title     = {Ecobalance of a solar thermal tower power plant with volumetric receiver},
  series = {SolarPACES 2010 : the CSP Conference: electricity, fuels and clean water from concentrated solar energy ; 21 to 24 September 2010, Perpignan, France},
  booktitle = {SolarPACES 2010 : the CSP Conference: electricity, fuels and clean water from concentrated solar energy ; 21 to 24 September 2010, Perpignan, France},
  publisher = {Soc. OSC},
  address   = {Saint Maur},
  pages     = {87 -- 88},
  year      = {2010},
  language  = {en}
}
@inproceedings{ZiolkoSchmitzSattleretal.2010,
  author    = {Ziolko, C. and Schmitz, M. and Sattler, Johannes, Christoph and Khedim, Ahmed and Hoffschmidt, Bernhard},
  title     = {AlSol - the open volumetric receiver technology moves to Africa},
  series = {SolarPACES 2010 : the CSP Conference: electricity, fuels and clean water from concentrated solar energy ; 21 to 24 September 2010, Perpignan, France},
  booktitle = {SolarPACES 2010 : the CSP Conference: electricity, fuels and clean water from concentrated solar energy ; 21 to 24 September 2010, Perpignan, France},
  publisher = {Soc. OSC},
  address   = {Saint Maur},
  pages     = {93 -- 94},
  year      = {2010},
  language  = {en}
}
@inproceedings{AnthrakidisRusackSchwarzer2010,
  author    = {Anthrakidis, Anette and Rusack, Markus and Schwarzer, Klemens},
  title     = {Low effort measurement method of PTC-efficiency},
  series = {SolarPACES 2010 : the CSP conference: electricity, fuels and clean water from concentrated solar energy ; 21 to 24 September 2010, Perpignan, France},
  booktitle = {SolarPACES 2010 : the CSP conference: electricity, fuels and clean water from concentrated solar energy ; 21 to 24 September 2010, Perpignan, France},
  publisher = {Soc. OSC},
  address   = {Saint Maur},
  pages     = {48 -- 49},
  year      = {2010},
  language  = {en}
}
@article{MukherjeePrahlBlecketal.2010,
  author    = {Mukherjee, Krishnendu and Prahl, Ulrich and Bleck, Wolfgang and Reisgen, Uwe and Schleser, Markus and Abdurakhmanov, Aydemir},
  title     = {Characterization and modelling techniques for gas metal arc welding of DP 600 sheet steels},
  series = {Materialwissenschaft und Werkstofftechnik},
  volume    = {41},
  journal   = {Materialwissenschaft und Werkstofftechnik},
  number    = {11},
  publisher = {Wiley-VCH},
  address   = {Weinheim},
  issn      = {1521-4052},
  doi       = {10.1002/mawe.201000692},
  pages     = {972 -- 983},
  year      = {2010},
  abstract  = {The objectives of the present work are to characterize the Gas Metal Arc Welding process of DP 600 sheet steel and to summarize the modelling techniques. The time-temperature evolution during the welding cycle was measured experimentally and modelled with the softwaretool SimWeld. To model the phase transformations during the welding cycle dilatometer tests were done to quantify the parameters for phase field modelling by MICRESS®. The important input parameters are interface mobility, nucleation density, etc. A contribution was made to include austenite to bainite transformation in MICRESS®. This is useful to predict the microstructure in the fast cooling segments. The phase transformation model is capable to predict the microstructure along the heating and cooling cycles of welding. Tensile tests have shown the evidence of failure at the heat affected zone, which has the ferrite-tempered martensite microstructure.},
  language  = {en}
}
@inproceedings{ReisgenSchoeneSchleseretal.2010,
  author    = {Reisgen, Uwe and Schoene, Jens and Schleser, Markus and Jerabek, Jakub and Keil, Allessandra},
  title     = {Theoretical and experimental investigations on textile-reinforced concrete spalling behavior},
  series = {Textile reinforced concrete : 2nd ICTRC : International RILEM Conference on Material Science : Aachen Germany, September 6 - 8, 2010. Vol. 1. (RILEM Proceedings PRO ; 75)},
  booktitle = {Textile reinforced concrete : 2nd ICTRC : International RILEM Conference on Material Science : Aachen Germany, September 6 - 8, 2010. Vol. 1. (RILEM Proceedings PRO ; 75)},
  editor    = {Brameshuber, Wolfgang},
  publisher = {RILEM Publ.},
  address   = {Bagneux},
  organization    = {International Conference of Textile Reinforced Concrete <2, 2010, Aachen>},
  isbn      = {978-2-35158-106-3},
  pages     = {153 -- 162},
  year      = {2010},
  language  = {en}
}
@article{ReisgenSchleserMokrovetal.2010,
  author    = {Reisgen, Uwe and Schleser, Markus and Mokrov, Oleg and Ahmed, Essam},
  title     = {Uni- and bi-axial deformation behavior of laser welded advanced high strength steel sheets},
  series = {Journal of materials processing technology},
  volume    = {210},
  journal   = {Journal of materials processing technology},
  number    = {15},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0924-0136},
  doi       = {http10.1016/j.jmatprotec.2010.08.003},
  pages     = {2188 -- 2196},
  year      = {2010},
  abstract  = {Bead-on-plate butt joints of 2.5 mm hot rolled DP600/DP600 and 1.2 mm cold rolled TRIP700/TRIP700 steel sheets were performed using 6 kW CO2 laser beam welding. The welding speed ranged from 1.5 to 3.0 and from 2.1 to 3.9 m/min in DP/DP and TRIP/TRIP steel weldments respectively. A top surface helium gas was used as a shielding gas at a flow rate of 20 l/min. Metallographic examinations and transverse tensile testing (DIN EN 895: 1995) were carried out to characterize the weldments. The formability of base metals and weldments were investigated by standard Erichsen test (DIN EN ISO 20482). It was found that the uniaxial plastic behavior of both DP600 and TRIP700 base metals was in agreement with Swift and modified Mecking-Kocks models respectively. In a perpendicular tensile test to the weld line, all specimens were fractured at the base metal however the strengths were somewhat higher than those of base metal. There was a significant reduction in formability caused by welding of both DP/DP and TRIP/TRIP steel weldments and the formability has been improved with the increase of the welding speed.},
  language  = {en}
}
@article{ReisgenSchleserMokrovetal.2010,
  author    = {Reisgen, Uwe and Schleser, Markus and Mokrov, Oleg and Ahmed, Essam},
  title     = {Shielding gas influences on laser weldability of tailored blanks of advanced automotive steels},
  series = {Applied surface science},
  volume    = {257},
  journal   = {Applied surface science},
  number    = {5},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0169-4332 (E-Journal); 0169-4332 (Print)},
  doi       = {10.1016/j.apsusc.2010.08.042},
  pages     = {1401 -- 1406},
  year      = {2010},
  abstract  = {The effects of shielding gas types and flow rates on CO2 laser weldability of DP600/TRIP700 steel sheets were studied in this work. The evaluated shielding gases were helium (He), argon (Ar) and different mixtures of He and Ar. Weld penetration, tensile strength and formability (Erichsen test) of laser welds were found to be strongly dependent upon the shielding gas types. The ability of shielding gas in removing plasma plume and thus increasing weld penetration is believed to be closely related to ionization potential and atomic weight which determine the period of plasma formation and disappearance. It was found that the higher helium shielding gas flow rate, the deeper weld penetration and the lower weld width.},
  language  = {en}
}
@article{AhmedReisgenSchleseretal.2010,
  author    = {Ahmed, Essam and Reisgen, Uwe and Schleser, Markus and Mokrov, Oleg},
  title     = {On formability of tailor laser welded blanks of DP/TRIP steel sheets},
  series = {Science and technology of welding and joining},
  volume    = {15},
  journal   = {Science and technology of welding and joining},
  number    = {5},
  publisher = {Maney},
  address   = {Leeds},
  issn      = {1743-2936},
  doi       = {10.1179/136217110X12731414739754},
  pages     = {337 -- 342},
  year      = {2010},
  abstract  = {This paper aims to evaluate the formability of tailor welded blanks of dual phase (DP600)/transformation induced plasticity (TRIP700) steel sheets. In this work, bead on plate butt joints of 2·5 mm DP600 and 1·2 mm TRIP700 steel sheets were performed using CO2 laser beam welding. Microhardness measurements and transverse tensile testing were carried out to characterise the welds. The formability of base metals and welds were investigated by standard Erichsen test. In a perpendicular tensile test to the weld line, all specimens were fractured at the TRIP base metal, and the strengths were somewhat higher than those of base metal. There was a significant reduction in formability caused by welding of the DP600/TRIP700 steel sheets, and the formability increased with increasing welding speed.},
  language  = {en}
}
@inproceedings{SchoeneReisgenSchleseretal.2010,
  author    = {Schoene, Jens and Reisgen, Uwe and Schleser, Markus and Jerabek, Jakub and Chudoba, Rostislav},
  title     = {Theoretical and experimental investigations on textile-reinforced concrete spalling behavior},
  series = {8th International PhD Symposium in Civil Engineering : Lyngby, June 20-23, 2010 : proceedings},
  booktitle = {8th International PhD Symposium in Civil Engineering : Lyngby, June 20-23, 2010 : proceedings},
  editor    = {Fisher, Gregor},
  publisher = {Technical University of Denmark, Dept. of Civil Engineering},
  address   = {Lyngby},
  organization    = {PhD Symposium in Civil Engineering <8, 2010, Lyngby> ; International Federation for Structural Concrete},
  isbn      = {9788778773012},
  pages     = {383 -- 388},
  year      = {2010},
  language  = {en}
}
@inproceedings{GallAbelAhlbrinketal.2010,
  author    = {Gall, J. and Abel, Dirk and Ahlbrink, N. and Pitz-Paal, R. and Andersson, J. and Diehl, M. and Teixeira Boura, Cristiano Jos{\´e} and Schmitz, M. and Hoffschmidt, Bernhard},
  title     = {Simulation and control of solar thermal power plants},
  series = {International Conference on Renewable Energies and Power Quality : ICREPQ '10 : Granada 23rd - 25th March 2010},
  booktitle = {International Conference on Renewable Energies and Power Quality : ICREPQ '10 : Granada 23rd - 25th March 2010},
  pages     = {1 -- 5},
  year      = {2010},
  language  = {en}
}
@incollection{ReimerBraunWellmeretal.2010,
  author    = {Reimer, Lars and Braun, Carsten and Wellmer, Georg and Behr, Marek and Ballmann, Josef},
  title     = {Development of a modular method for computational aero-structural analysis of aircraft},
  series = {Summary of flow modulation and fluid-structure interaction findings. Results of the Collaborative Research Center SFB 401 at the RWTH Aachen University, Aachen, Germany, 1997-2008 / ed.: Wolfgang Schr{\"o}der. Notes on numerical fluid mechanics and multidisciplinary design. Vol. 109},
  booktitle = {Summary of flow modulation and fluid-structure interaction findings. Results of the Collaborative Research Center SFB 401 at the RWTH Aachen University, Aachen, Germany, 1997-2008 / ed.: Wolfgang Schr{\"o}der. Notes on numerical fluid mechanics and multidisciplinary design. Vol. 109},
  publisher = {Springer},
  address   = {Berlin},
  isbn      = {978-3-642-04087-0},
  pages     = {205 -- 238},
  year      = {2010},
  language  = {en}
}
@inproceedings{KapoorBraunBoller2010,
  author    = {Kapoor, Hrshi and Braun, Carsten and Boller, Christian},
  title     = {Modelling and optimisation of maintenance intervals to realize structural health monitoring applications on aircraft},
  series = {Structural health monitoring 2010 : proceedings of the Fifth European Workshop on Structural Health Monitoring held at Sorrento, Naples, Italy, June 28 - July 4, 2010 ; [EWSHM]},
  booktitle = {Structural health monitoring 2010 : proceedings of the Fifth European Workshop on Structural Health Monitoring held at Sorrento, Naples, Italy, June 28 - July 4, 2010 ; [EWSHM]},
  editor    = {Casciati, Fabio},
  publisher = {DEStech Publ.},
  address   = {Lancaster, Pa.},
  isbn      = {978-1-60595-024-2},
  pages     = {55 -- 63},
  year      = {2010},
  language  = {en}
}
@inproceedings{KapoorBollerGiljohannetal.2010,
  author    = {Kapoor, Hrshi and Boller, Christian and Giljohann, Sebastian and Braun, Carsten},
  title     = {Strategies for structural health monitoring implementation potential assessment in aircraft operational life extension considerations},
  series = {2nd International Symposium on NDT in Aerospace : November 22-24, 2010 Hamburg, Germany},
  booktitle = {2nd International Symposium on NDT in Aerospace : November 22-24, 2010 Hamburg, Germany},
  publisher = {Dt. Gesellschaft f{\"u}r Zerst{\"o}rungsfreie Pr{\"u}fung},
  address   = {Berlin},
  organization    = {Deutsche Gesellschaft f{\"u}r Zerst{\"o}rungsfreie Pr{\"u}fung},
  isbn      = {978-3-940283-28-3},
  pages     = {9},
  year      = {2010},
  language  = {en}
}
@inproceedings{PenneProfittlichRingbecketal.2010,
  author    = {Penne, Jochen and Profittlich, Martin and Ringbeck, Thorsten and Buxbaum, Bernd},
  title     = {Touchless detailed 3D scan of human hand anatomy using time-of-flight cameras},
  series = {Proceedings of the International Conference on 3D Body Scanning Technologies : Lugano, Switzerland, 19-20 October 2010},
  booktitle = {Proceedings of the International Conference on 3D Body Scanning Technologies : Lugano, Switzerland, 19-20 October 2010},
  editor    = {D, Nicola D'Apuzzo},
  publisher = {Hometrica Consulting},
  address   = {Z{\"u}rich},
  isbn      = {978-3-033-02714-5},
  pages     = {361 -- 369},
  year      = {2010},
  language  = {en}
}
@inproceedings{UibelBlass2010,
  author    = {Uibel, Thomas and Blaß, Hans Joachim},
  title     = {A new method to determine suitable spacings and distances for self-tapping screws},
  series = {Meeting ... / International Council for Research and Innovation in Building and Construction, Working Commission W18 - Timber Structures},
  volume    = {43},
  booktitle = {Meeting ... / International Council for Research and Innovation in Building and Construction, Working Commission W18 - Timber Structures},
  publisher = {Lehrstuhl f{\"u}r Ingenieurholzbau und Baukonstruktionen},
  address   = {Karlsruhe},
  issn      = {1864-1784},
  year      = {2010},
  abstract  = {The determination of spacing, edge and end distance requirements for self-tapping screws requires numerous and comprehensive insertion tests. Yet the results of such tests cannot be transferred to other types of screws or even to screws of different diameter because of differences in shape or geometry. To reduce the effort of insertion tests a new method was developed which allows the estimation of required spacings, distances and timber thickness.},
  language  = {en}
}
@inproceedings{UibelBlass2010,
  author    = {Uibel, Thomas and Blaß, Hans Joachim},
  title     = {Determining Suitable Spacings and Distances for Self-tapping Screws by Experimental and Numerical Studies},
  series = {Proceedings of the 11th World Conference on Timber Engineering, WCTE 2010 : World Conference on Timber Engineering; [June 20 - 24, 2010, Riva del Garda, Trento, Italy] . Vol. III, Riva del Garda, Italy 2010},
  booktitle = {Proceedings of the 11th World Conference on Timber Engineering, WCTE 2010 : World Conference on Timber Engineering; [June 20 - 24, 2010, Riva del Garda, Trento, Italy] . Vol. III, Riva del Garda, Italy 2010},
  editor    = {Cecotti, A.},
  pages     = {669 -- 670},
  year      = {2010},
  language  = {en}
}
@article{HeinzelSchaeferMuelleretal.2010,
  author    = {Heinzel, Alexander and Sch{\"a}fer, Ralf and M{\"u}ller, Hans-Wilhelm and Schieffer, Andre and Ingenhag, Ariane and Northoff, Georg and Franz, Matthias and Hautzel, Hubertus},
  title     = {Differential modulation of valence and arousal in high-alexithymic and low-alexithymic individuals},
  series = {Neuroreport},
  volume    = {21},
  journal   = {Neuroreport},
  number    = {15},
  publisher = {Lippincott Williams \& Wilkins},
  address   = {London},
  issn      = {1473-558X},
  doi       = {10.1097/WNR.0b013e32833f38e0},
  pages     = {998 -- 1002},
  year      = {2010},
  abstract  = {High-alexithymic individuals are characterized by an impaired ability to identify and communicate emotions whereas low-alexithymic individuals have a wide-ranging ability to deal with emotions. This study examined the hypothesis that valence and arousal modifications of emotional stimuli differentially modulate cortical regions in high-alexithymic and low-alexithymic individuals. To this end, 28 high-alexithymic and 25 low-alexithymic individuals were investigated with event-related fMRI using visual emotional stimuli. We found differential neural activations in the dorsal anterior cingulate, the insula and the amygdala. We suggest that these differences may account for the impaired ability of high-alexithymic individuals to appropriately handle emotional stimuli.},
  language  = {en}
}
@article{HeinzelSchaeferMuelleretal.2010,
  author    = {Heinzel, Alexander and Sch{\"a}fer, Ralf and M{\"u}ller, Hans-Wilhelm and Schieffer, Andre and Ingenhag, Ariane and Eickhoff, Simon B. and Northoff, Georg and Franz, Matthias and Hautzel, Hubertus},
  title     = {Increased Activation of the Supragenual Anterior Cingulate Cortex during Visual Emotional Processing in Male Subjects with High Degrees of Alexithymia: An Event-Related fMRI Study},
  series = {Psychotherapy and Psychosomatics},
  volume    = {79},
  journal   = {Psychotherapy and Psychosomatics},
  number    = {6},
  publisher = {Karger},
  address   = {Basel},
  issn      = {0033-3190},
  doi       = {10.1159/000320121},
  pages     = {363 -- 370},
  year      = {2010},
  abstract  = {Background: One of the most prominent neurobiological models of alexithymia assumes an altered function of the anterior cingulate cortex (ACC) as the crucial neural correlate of alexithymia. So far functional imaging studies have yielded inconclusive results. Therefore, we tested this hypothesis in healthy alexithymics and nonalexithymics in an event-related fMRI study. Methods: Thirty high- and 30 low-alexithymic right-handed male subjects (selected by the 20-item Toronto Alexithymia Scale, TAS-20) were investigated with event-related fMRI using a picture viewing paradigm. The stimuli consisted of happy, fearful and neutral facial expressions (Ekman-Friesen) as well as positive, negative and neutral pictures from the International Affective Picture System. Results: Contrasting the high-alexithymic with the low-alexithymic group we observed increased activation of the supragenual ACC for different emotional valences as well as for different emotional stimuli. Moreover, there was a positive correlation of the ACC with the individual TAS-20 scores but no correlations with the individual Beck Depression Inventory scores. Additionally, there was no difference in activity of the amygdala. Conclusions: We demonstrated that the supragenual ACC is constantly activated more strongly in alexithymic subjects and that this activation is related to the symptoms of alexithymia and not to associated symptoms such as depression. Therefore, our findings support the hypothesis of an altered function of the ACC in alexithymia.},
  language  = {en}
}
@article{HerzogPietrzykShahetal.2010,
  author    = {Herzog, Hans and Pietrzyk, Uwe and Shah, N. Jon and Ziemons, Karl},
  title     = {The current state, challenges and perspectives of MR-PET},
  series = {Neuroimage},
  volume    = {49},
  journal   = {Neuroimage},
  number    = {3},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1053-8119},
  doi       = {10.1016/j.neuroimage.2009.10.036},
  pages     = {2072 -- 2082},
  year      = {2010},
  abstract  = {Following the success of PET/CT during the last decade and the recent increasing proliferation of SPECT/CT, another hybrid imaging instrument has been gaining more and more interest: MR-PET. First combined, simultaneous PET and MR studies carried out in small animals demonstrated the feasibility of the new approach. Concurrently, some prototypes of an MR-PET scanner for simultaneous human brain studies have been built, their performance is being tested and preliminary applications have already been shown. Through this pioneering work, it has become clear that advances in the detector design are necessary for further optimization. Recently, the different issues related to the present state and future prospects of MR-PET were presented and discussed during an international 2-day workshop at the Forschungszentrum J{\"u}lich, Germany, held after, and in conjunction with, the 2008 IEEE Nuclear Science Symposium and Medical Imaging Conference in Dresden, Germany on October 27-28, 2008. The topics ranged from small animal MR-PET imaging to human MR-BrainPET imaging, new detector developments, challenges/opportunities for ultra-high field MR-PET imaging and considerations of possible future research and clinical applications. This report presents a critical summary of the contributions made to the workshop.},
  language  = {en}
}
@article{BeerStreunHombachetal.2010,
  author    = {Beer, S. and Streun, M. and Hombach, T. and Buehler, J. and Jahnke, S. and Khodaverdi, M. and Larue, H. and Minwuyelet, S. and Parl, C. and Roeb, G. and Schurr, U. and Ziemons, Karl},
  title     = {Design and initial performance of PlanTIS: a high-resolution positron emission tomograph for plants},
  series = {Physics in Medicine and Biology},
  volume    = {55},
  journal   = {Physics in Medicine and Biology},
  number    = {3},
  publisher = {IOP},
  address   = {Bristol},
  issn      = {1361-6560},
  doi       = {10.1088/0031-9155/55/3/006},
  pages     = {635 -- 646},
  year      = {2010},
  abstract  = {Positron emitters such as 11C, 13N and 18F and their labelled compounds are widely used in clinical diagnosis and animal studies, but can also be used to study metabolic and physiological functions in plants dynamically and in vivo. A very particular tracer molecule is 11CO2 since it can be applied to a leaf as a gas. We have developed a Plant Tomographic Imaging System (PlanTIS), a high-resolution PET scanner for plant studies. Detectors, front-end electronics and data acquisition architecture of the scanner are based on the ClearPET™ system. The detectors consist of LSO and LuYAP crystals in phoswich configuration which are coupled to position-sensitive photomultiplier tubes. Signals are continuously sampled by free running ADCs, and data are stored in a list mode format. The detectors are arranged in a horizontal plane to allow the plants to be measured in the natural upright position. Two groups of four detector modules stand face-to-face and rotate around the field-of-view. This special system geometry requires dedicated image reconstruction and normalization procedures. We present the initial performance of the detector system and first phantom and plant measurements.},
  language  = {en}
}
@article{Helmig2010,
  author    = {Helmig, Ilka},
  title     = {Nitty - fontnames illustrated},
  series = {Slanted},
  journal   = {Slanted},
  number    = {11},
  publisher = {Slanted Publishers},
  address   = {Karlsruhe},
  issn      = {1867-6510},
  pages     = {68 -- 69},
  year      = {2010},
  language  = {en}
}
@article{ChristenKowalskiBartelt2010,
  author    = {Christen, Marc and Kowalski, Julia and Bartelt, Perry},
  title     = {RAMMS: Numerical simulation of dense snow avalanches in three-dimensional terrain},
  series = {Cold Regions Science and Technology},
  volume    = {63},
  journal   = {Cold Regions Science and Technology},
  number    = {1-2},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1872-7441},
  doi       = {10.1016/j.coldregions.2010.04.005},
  pages     = {1 -- 14},
  year      = {2010},
  abstract  = {Numerical avalanche dynamics models have become an essential part of snow engineering. Coupled with field observations and historical records, they are especially helpful in understanding avalanche flow in complex terrain. However, their application poses several new challenges to avalanche engineers. A detailed understanding of the avalanche phenomena is required to construct hazard scenarios which involve the careful specification of initial conditions (release zone location and dimensions) and definition of appropriate friction parameters. The interpretation of simulation results requires an understanding of the numerical solution schemes and easy to use visualization tools. We discuss these problems by presenting the computer model RAMMS, which was specially designed by the SLF as a practical tool for avalanche engineers. RAMMS solves the depth-averaged equations governing avalanche flow with accurate second-order numerical solution schemes. The model allows the specification of multiple release zones in three-dimensional terrain. Snow cover entrainment is considered. Furthermore, two different flow rheologies can be applied: the standard Voellmy-Salm (VS) approach or a random kinetic energy (RKE) model, which accounts for the random motion and inelastic interaction between snow granules. We present the governing differential equations, highlight some of the input and output features of RAMMS and then apply the models with entrainment to simulate two well-documented avalanche events recorded at the Vall{\´e}e de la Sionne test site.},
  language  = {en}
}
@article{ChristenBarteltKowalski2010,
  author    = {Christen, Marc and Bartelt, Perry and Kowalski, Julia},
  title     = {Back calculation of the In den Arelen avalanche with RAMMS: Interpretation of model results},
  series = {Annals of Glaciology},
  volume    = {51},
  journal   = {Annals of Glaciology},
  number    = {54},
  publisher = {Cambridge University Press},
  address   = {Cambridge},
  isbn      = {1727-5644},
  doi       = {10.3189/172756410791386553},
  pages     = {161 -- 168},
  year      = {2010},
  abstract  = {Two- and three-dimensional avalanche dynamics models are being increasingly used in hazard-mitigation studies. These models can provide improved and more accurate results for hazard mapping than the simple one-dimensional models presently used in practice. However, two- and three-dimensional models generate an extensive amount of output data, making the interpretation of simulation results more difficult. To perform a simulation in three-dimensional terrain, numerical models require a digital elevation model, specification of avalanche release areas (spatial extent and volume), selection of solution methods, finding an adequate calculation resolution and, finally, the choice of friction parameters. In this paper, the importance and difficulty of correctly setting up and analysing the results of a numerical avalanche dynamics simulation is discussed. We apply the two-dimensional simulation program RAMMS to the 1968 extreme avalanche event In den Arelen. We show the effect of model input variations on simulation results and the dangers and complexities in their interpretation.},
  language  = {en}
}
@article{PieperKlein2010,
  author    = {Pieper, Martin and Klein, Peter},
  title     = {Numerical solution of the heat equation with non-linear, time derivative-dependent source term},
  series = {International Journal for Numerical Methods in Engineering},
  volume    = {84},
  journal   = {International Journal for Numerical Methods in Engineering},
  number    = {10},
  publisher = {Wiley},
  address   = {Chichester},
  issn      = {0029-5981},
  doi       = {10.1002/nme.2937},
  pages     = {1205 -- 1221},
  year      = {2010},
  abstract  = {The mathematical modeling of heat conduction with adsorption effects in coated metal structures yields the heat equation with piecewise smooth coefficients and a new kind of source term. This term is special, because it is non-linear and furthermore depends on a time derivative. In our approach we reformulated this as a new problem for the usual heat equation, without source term but with a new non-linear coefficient. We gave an existence and uniqueness proof for the weak solution of the reformulated problem. To obtain a numerical solution, we developed a semi-implicit and a fully implicit finite volume method. We compared these two methods theoretically as well as numerically. Finally, as practical application, we simulated the heat conduction in coated aluminum fibers with adsorption in the zeolite coating. Copyright © 2010 John Wiley \& Sons, Ltd.},
  language  = {en}
}
@article{Digel2010,
  author    = {Digel, Ilya},
  title     = {In-situ biological decontamination of an ice melting probe},
  year      = {2010},
  language  = {en}
}
@article{KozhalakovaZhubanovaMansurovetal.2010,
  author    = {Kozhalakova, A. A. and Zhubanova, Azhar A. and Mansurov, Z. A. and Digel, Ilya and Tazhibayeva, S. M. and Artmann, Gerhard and Temiz Artmann, Ayseg{\"u}l},
  title     = {Adsorption of bacterial lipopolysaccharides on carbonized rice shell},
  series = {Science of Central Asia (2010)},
  journal   = {Science of Central Asia (2010)},
  pages     = {50 -- 54},
  year      = {2010},
  language  = {en}
}
@article{KurzLinderTrzewiketal.2010,
  author    = {Kurz, R. and Linder, Peter and Trzewik, J{\"u}rgen and R{\"u}ffer, M. and Artmann, Gerhard and Digel, Ilya and Rothermel, A. and Robitzki, A. and Temiz Artmann, Ayseg{\"u}l},
  title     = {Contractile tension and beating rates of self-exciting monolayers and 3D-tissue constructs of neonatal rat cardiomyocytes},
  series = {Medical and Biological Engineering and Computing},
  volume    = {48},
  journal   = {Medical and Biological Engineering and Computing},
  number    = {1},
  publisher = {Springer Nature},
  address   = {Cham},
  issn      = {1741-0444},
  doi       = {10.1007/s11517-009-0552-y},
  pages     = {59 -- 65},
  year      = {2010},
  abstract  = {The CellDrum technology (The term 'CellDrum technology' includes a couple of slightly different technological setups for measuring lateral mechanical tension in various types of cell monolayers or 3D-tissue constructs) was designed to quantify the contraction rate and mechanical tension of self-exciting cardiac myocytes. Cells were grown either within flexible, circular collagen gels or as monolayer on top of respective 1-mum thin silicone membranes. Membrane and cells were bulged outwards by air pressure. This biaxial strain distribution is rather similar the beating, blood-filled heart. The setup allowed presetting the mechanical residual stress level externally by adjusting the centre deflection, thus, mimicking hypertension in vitro. Tension was measured as oscillating differential pressure change between chamber and environment. A 0.5-mm thick collagen-cardiac myocyte tissue construct induced after 2 days of culturing (initial cell density 2 x 10(4) cells/ml), a mechanical tension of 1.62 +/- 0.17 microN/mm(2). Mechanical load is an important growth regulator in the developing heart, and the orientation and alignment of cardiomyocytes is stress sensitive. Therefore, it was necessary to develop the CellDrum technology with its biaxial stress-strain distribution and defined mechanical boundary conditions. Cells were exposed to strain in two directions, radially and circumferentially, which is similar to biaxial loading in real heart tissues. Thus, from a biomechanical point of view, the system is preferable to previous setups based on uniaxial stretching.},
  language  = {en}
}
@article{GarhoferBekBoehmetal.2010,
  author    = {Garhofer, Gerhard and Bek, Toke and Boehm, Andreas G. and Gherghel, Doina and Grundwald, Juan and Jeppesen, Peter and Kergoat, H{\´e}l{\`e}ne and Kotliar, Konstantin and Lanzl, Ines and Lovasik, John V. and Nagel, Edgar and Vilser, Walthard and Orgul, Selim and Schmetterer, Leopold},
  title     = {Use of the retinal vessel analyzer in ocular blood flow research},
  series = {Acta Ophthalmol},
  volume    = {88},
  journal   = {Acta Ophthalmol},
  number    = {7},
  publisher = {Wiley-Blackwell},
  address   = {Oxford},
  issn      = {1755-3768},
  doi       = {10.1111/j.1755-3768.2009.01587.x},
  pages     = {717 -- 722},
  year      = {2010},
  abstract  = {The present article describes a standard instrument for the continuous online determination of retinal vessel diameters, the commercially available retinal vessel analyzer. This report is intended to provide informed guidelines for measuring ocular blood flow with this system. The report describes the principles underlying the method and the instruments currently available, and discusses clinical protocol and the specific parameters measured by the system. Unresolved questions and the possible limitations of the technique are also discussed.},
  language  = {en}
}
@article{PresslerEsefeldScherretal.2010,
  author    = {Pressler, Axel and Esefeld, Katrin and Scherr, Johannes and Ali, Mohammad and Hanssen, Henner and Kotliar, Konstantin and Lanzl, Ines and Halle, Martin and Kaemmerer, Harald and Schmidt-Trucks{\"a}ss, Arno and Hager, Alfred},
  title     = {Structural alterations of retinal arterioles in adults late after repair of aortic isthmic coarctation},
  series = {The American Journal of Cardiology},
  volume    = {105},
  journal   = {The American Journal of Cardiology},
  number    = {5},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0002-9149},
  doi       = {10.1016/j.amjcard.2009.10.070},
  pages     = {740 -- 744},
  year      = {2010},
  abstract  = {Patients after coarctation repair still have an increased risk of cardiovascular or cerebrovascular events. This has been explained by the persisting hypertension and alterations in the peripheral vessels. However, involvement of the central vessels such as the retinal arteries is virtually unknown. A total of 34 patients after coarctation repair (22 men and 12 women; 23 to 58 years old, age range 0 to 32 years at surgical repair) and 34 nonhypertensive controls underwent structural and functional retinal vessel analysis. Using structural analysis, the vessel diameters were measured. Using functional analysis, the endothelium-dependent vessel dilation in response to flicker light stimulation was assessed. In the patients after coarctation repair, the retinal arteriolar diameter was significantly reduced compared to that of the controls (median 182 μm, first to third quartile 171 to 197; vs 197 μm, first to third quartile 193 to 206; p <0.001). These findings were independent of the peripheral blood pressure and age at intervention. No differences were found for venules. The functional analysis findings were not different between the patients and controls (maximum dilation 3.5\%, first to third quartile 2.1\% to 4.5\% vs 3.6\%, first to third quartile 2.2\% to 4.3\%; p = 0.81), indicating preserved autoregulative mechanisms. In conclusion, the retinal artery diameter is reduced in patients after coarctation repair, independent of their current blood pressure level and age at intervention. As a structural marker of chronic vessel damage associated with past, current, or future hypertension, retinal arteriolar narrowing has been linked to stroke incidence. These results indicate an involvement of cerebral microcirculation in aortic coarctation, despite timely repair, and might contribute to explain the increased rate of cerebrovascular events in such patients.},
  language  = {en}
}
@article{KotliarNagelVilseretal.2010,
  author    = {Kotliar, Konstantin and Nagel, Edgar and Vilser, Walthard and Seidova, Seid-Fatima and Lanzl, Ines},
  title     = {Microstructural alterations of retinal arterial blood column along the vessel axis in systemic hypertension},
  series = {Investigative Ophthalmology \& Visual Science, IOVS},
  volume    = {51},
  journal   = {Investigative Ophthalmology \& Visual Science, IOVS},
  number    = {4},
  publisher = {ARVO},
  address   = {Rockville, Md.},
  issn      = {0146-0404},
  doi       = {10.1167/iovs.09-3649},
  pages     = {2165 -- 2172},
  year      = {2010},
  abstract  = {Purpose: Image analysis by the retinal vessel analyzer (RVA) observes retinal vessels in their dynamic state online noninvasively along a chosen vessel segment. It has been found that high-frequency diameter changes in the retinal artery blood column along the vessel increase significantly in anamnestically healthy volunteers with increasing age and in patients with glaucoma during vascular dilation. This study was undertaken to investigate whether longitudinal sections of the retinal artery blood column are altered in systemic hypertension. Methods: Retinal arteries of 15 untreated patients with essential arterial hypertension (age, 50.9 ± 11.9 years) and of 15 age-matched anamnestically healthy volunteers were examined by RVA. After baseline assessment, a monochromatic luminance flicker (530-600 nm; 12.5 Hz; 20 s) was applied to evoke retinal vasodilation. Differences in amplitude and frequency of spatial artery blood column diameter change along segments (longitudinal arterial profiles) of 1 mm in length were measured and analyzed using Fourier transformation. Results: In the control group, average reduced power spectra (ARPS) of longitudinal arterial profiles did not differ when arteries changed from constriction to dilation. In the systemic hypertension group, ARPS during constriction, baseline, and restoration were identical and differed from ARPS during dilation (P < 0.05). Longitudinal arterial profiles in both groups showed significant dissimilitude at baseline and restoration (P < 0.05). Conclusions: The retinal artery blood column demonstrates microstructural alterations in systemic hypertension and is less irregular along the vessel axis during vessel dilation. These microstructural changes may be an indication of alterations in vessel wall rigidity, vascular endothelial function, and smooth muscle cells in this disease, leading to impaired perfusion and regulation.},
  language  = {en}
}
@article{HaselgruberMautnerThiele2010,
  author    = {Haselgruber, Nikolaus and Mautner, Karin and Thiele, Jan},
  title     = {Usage Space Analysis for Reliability Testing},
  series = {Quality and Reliability Engineering International},
  volume    = {26},
  journal   = {Quality and Reliability Engineering International},
  number    = {8},
  publisher = {Wiley},
  address   = {New York},
  issn      = {1099-1638},
  doi       = {10.1002/qre.1155},
  pages     = {877 -- 885},
  year      = {2010},
  abstract  = {During the development process of a complex technical product, one widely used and important technique is accelerated testing where the applied stress on a component is chosen to exceed the reference stress, i.e. the stress encountered in field operation, in order to reduce the time to failure. For that, the reference stress has to be known. Since a complex technical product may fail regarding numerous failure modes, stress in general is highly dimensional rather than scalar. In addition, customers use their products individually, i.e. field operation should be described by a distribution rather than by one scalar stress value. In this paper, a way to span the customer usage space is shown. It allows the identification of worst case reference stress profiles in significantly reduced dimensions with minimal loss of information. The application example shows that even for a complex product like a combustion engine, stress information can be compressed significantly. With low measurement effort it turned out that only three reference stress cycles were sufficient to cover a broad range of customer stress variety.},
  language  = {en}
}
@inproceedings{HavermannSeilerHenning2010,
  author    = {Havermann, Marc and Seiler, F. and Henning, P.},
  title     = {Shock Tunnel Experiments and CFD Simulation of Lateral Jet Interaction in Hypersonic Flows},
  series = {New Results in Numerical and Experimental Fluid Mechanics VII; Contributions to the 16th STAB/DGLR Symposium Aachen, Germany 2008},
  booktitle = {New Results in Numerical and Experimental Fluid Mechanics VII; Contributions to the 16th STAB/DGLR Symposium Aachen, Germany 2008},
  editor    = {Dillmann, Andreas and Heller, Gerd and Klaas, Michael and Kreplin, Hans-Peter and Nitsche, Wolfgang and Schr{\"o}der, Wolfgang},
  publisher = {Springer},
  address   = {Berlin},
  isbn      = {9783642142437},
  doi       = {10.1007/978-3-642-14243-7_45},
  pages     = {365 -- 372},
  year      = {2010},
  language  = {en}
}
@article{LettiniHavermannGuidettietal.2010,
  author    = {Lettini, Antonio and Havermann, Marc and Guidetti, Marco and Fornaciari, Andrea},
  title     = {Improved functionalities and energy saving potential on mobile machines combining electronics with flow sharing valve and variable displacement pump},
  series = {IFK 7, 7th International Fluid Power Conference, Efficiency through Fluid Power, 7. Internationales Fluidtechnisches Kolloquium, Workshop Proceedings, Vol. 3, Aachen, DE, 22.-24. Mar, 2010},
  journal   = {IFK 7, 7th International Fluid Power Conference, Efficiency through Fluid Power, 7. Internationales Fluidtechnisches Kolloquium, Workshop Proceedings, Vol. 3, Aachen, DE, 22.-24. Mar, 2010},
  publisher = {-},
  isbn      = {978-3-940565-92-1},
  pages     = {103 -- 114},
  year      = {2010},
  language  = {en}
}
@article{ReckerBosschaertsWagemakersetal.2010,
  author    = {Recker, Elmar and Bosschaerts, Walter and Wagemakers, Rolf and Hendrick, Patrick and Funke, Harald and B{\"o}rner, Sebastian},
  title     = {Experimental study of a round jet in cross-flow at low momentum ratio},
  series = {15th International Symposium on Applications of Laser Techniques to Fluid Mechanics Lisbon, Portugal, 05-08 July, 2010 - 1},
  journal   = {15th International Symposium on Applications of Laser Techniques to Fluid Mechanics Lisbon, Portugal, 05-08 July, 2010 - 1},
  pages     = {1 -- 13},
  year      = {2010},
  language  = {en}
}
@article{FunkeBoernerRobinsonetal.2010,
  author    = {Funke, Harald and B{\"o}rner, Sebastian and Robinson, A. and Hendrick, P. and Recker, E.},
  title     = {Low NOx H2 combustion for industrial gas turbines of various power ranges},
  series = {5th International Gas Turbine Conference ETN-IGTC, ETN-2010-42, Brussels, Belgium, October 2010},
  journal   = {5th International Gas Turbine Conference ETN-IGTC, ETN-2010-42, Brussels, Belgium, October 2010},
  year      = {2010},
  language  = {en}
}
@article{FunkeRobinsonHendricketal.2010,
  author    = {Funke, Harald and Robinson, A. E. and Hendrick, P. and Wagemakers, R.},
  title     = {Design and Testing of a Micromix Combustor With Recuperative Wall Cooling for a Hydrogen Fuelled µ-Scale Gas Turbine},
  series = {Proceedings of the ASME Turbo Expo 2010 : presented at the 2010 ASME Turbo Expo, June 14 - 18, 2010, Glasgow, UK / sponsored by the International Gas Turbine Institute / Vol. 5: Industrial and cogeneration ; microturbines and small turbomachinery ; oil and gas applications ; wind turbine technology},
  journal   = {Proceedings of the ASME Turbo Expo 2010 : presented at the 2010 ASME Turbo Expo, June 14 - 18, 2010, Glasgow, UK / sponsored by the International Gas Turbine Institute / Vol. 5: Industrial and cogeneration ; microturbines and small turbomachinery ; oil and gas applications ; wind turbine technology},
  publisher = {ASME},
  address   = {New York, NY},
  isbn      = {978-0-7918-4400-7},
  pages     = {587 -- 596},
  year      = {2010},
  language  = {en}
}
@article{Ferrein2010,
  author    = {Ferrein, Alexander},
  title     = {golog.lua: Towards a Non-Prolog Implementation of Golog for Embedded Systems},
  pages     = {20 -- 28},
  year      = {2010},
  language  = {en}
}
@article{Ferrein2010,
  author    = {Ferrein, Alexander},
  title     = {golog.lua: Towards a Non-Prolog Implementation of Golog for Embedded Systems},
  series = {Cognitive Robotics / Lakemeyer, Gerhard (ed.)},
  journal   = {Cognitive Robotics / Lakemeyer, Gerhard (ed.)},
  pages     = {1 -- 15},
  year      = {2010},
  language  = {en}
}
@article{FerreinSteinbauer2010,
  author    = {Ferrein, Alexander and Steinbauer, Gerald},
  title     = {On the Way to High-Level Programming for Resource-Limited Embedded Systems with Golog},
  series = {Simulation, Modeling, and Programming for Autonomous Robots},
  journal   = {Simulation, Modeling, and Programming for Autonomous Robots},
  pages     = {229 -- 240},
  year      = {2010},
  language  = {en}
}
@article{Ferrein2010,
  author    = {Ferrein, Alexander},
  title     = {Robot controllers for highly dynamic environments with real-time constraints},
  series = {K{\"u}nstliche Intelligenz : KI. 24 (2010), H. 2},
  journal   = {K{\"u}nstliche Intelligenz : KI. 24 (2010), H. 2},
  isbn      = {1610-1987},
  pages     = {175 -- 178},
  year      = {2010},
  language  = {en}
}
@article{RensVarzinczakMeyeretal.2010,
  author    = {Rens, Gavin and Varzinczak, Ivan and Meyer, Thomas and Ferrein, Alexander},
  title     = {A Logic for Reasoning about Actions and Explicit Observations},
  series = {AI 2010: Advances in Artificial Intelligence 23rd Australasian Joint Conference, Adelaide, Australia, December 7-10, 2010. Proceedings},
  journal   = {AI 2010: Advances in Artificial Intelligence 23rd Australasian Joint Conference, Adelaide, Australia, December 7-10, 2010. Proceedings},
  publisher = {Springer},
  address   = {Berlin},
  isbn      = {978-3-642-17431-5},
  pages     = {395 -- 404},
  year      = {2010},
  language  = {en}
}
@article{NiemuellerFerreinBecketal.2010,
  author    = {Niem{\"u}ller, Tim and Ferrein, Alexander and Beck, Daniel and Lakemeyer, Gerhard},
  title     = {Design Principles of the Component-Based Robot Software Framework Fawkes},
  series = {Simulation, Modeling, and Programming for Autonomous Robots},
  journal   = {Simulation, Modeling, and Programming for Autonomous Robots},
  pages     = {300 -- 311},
  year      = {2010},
  language  = {en}
}
@article{NiemuellerFerreinLakemeyer2010,
  author    = {Niem{\"u}ller, Tim and Ferrein, Alexander and Lakemeyer, Gerhard},
  title     = {A Lua-based Behavior Engine for Controlling the Humanoid Robot Nao},
  series = {RoboCup 2009: Robot Soccer World Cup XIII},
  journal   = {RoboCup 2009: Robot Soccer World Cup XIII},
  pages     = {240 -- 251},
  year      = {2010},
  language  = {en}
}
@article{FerreinSiebelSteinbauer2010,
  author    = {Ferrein, Alexander and Siebel, Nils T. and Steinbauer, Gerald},
  title     = {Hybrid control for autonomous systems — Integrating learning, deliberation and reactive control},
  series = {Robotics and Autonomous Systems},
  volume    = {58},
  journal   = {Robotics and Autonomous Systems},
  number    = {9},
  isbn      = {0921-8890},
  pages     = {1037 -- 1038},
  year      = {2010},
  language  = {en}
}
@article{SchifferFerreinLakemeyer2010,
  author    = {Schiffer, Stefan and Ferrein, Alexander and Lakemeyer, Gerhard},
  title     = {Proceedings of the Fourth International Conference on Intelligent Robotics and Applications (ICIRA 2011)},
  series = {Proceedings of the Fourth International Conference on Intelligent Robotics and Applications (ICIRA 2011)},
  journal   = {Proceedings of the Fourth International Conference on Intelligent Robotics and Applications (ICIRA 2011)},
  pages     = {1 -- 10},
  year      = {2010},
  language  = {en}
}
@article{LeimenaArtmannDachwaldetal.2010,
  author    = {Leimena, W. and Artmann, Gerhard and Dachwald, Bernd and Temiz Artmann, Ayseg{\"u}l and Gossmann, Matthias and Digel, Ilya},
  title     = {Feasibility of an in-situ microbial decontamination of an ice-melting probe},
  series = {Eurasian Chemico-Technological Journal. 12 (2010), H. 2},
  journal   = {Eurasian Chemico-Technological Journal. 12 (2010), H. 2},
  isbn      = {1562-3920},
  pages     = {145 -- 150},
  year      = {2010},
  language  = {en}
}
@article{BehbahaniMaiBergmannetal.2010,
  author    = {Behbahani, Mehdi and Mai, A. and Bergmann, B. and Waluga, C. and Behr, M. and Tran, L. and Vonderstein, K. and Mottaghy, K.},
  title     = {Modeling and Numerical Simulation of Blood Damage},
  year      = {2010},
  language  = {en}
}
@article{BehbahaniMaiWalugaetal.2010,
  author    = {Behbahani, Mehdi and Mai, A. and Waluga, C. and Bergmann, B. and Tran, L. and Vonderstein, K. and Behr, M. and Mottaghy, K.},
  title     = {Numerical Modeling of Flow-Related Thrombus Formation under Physiological and Non-Physiological Flow Conditions},
  series = {Acta Physiologica},
  volume    = {198},
  journal   = {Acta Physiologica},
  number    = {Supplement 677},
  isbn      = {1748-1716},
  pages     = {185},
  year      = {2010},
  language  = {en}
}
@article{BehbahaniProbstMaietal.2010,
  author    = {Behbahani, Mehdi and Probst, M. and Mai, A. and Behr, M. and Tran, L. and Vonderstein, K. and Mottaghy, K.},
  title     = {Numerical Prediction of Blood Damage in Biomedical Devices},
  year      = {2010},
  language  = {en}
}
@article{ProbstBehbahaniBorrmannetal.2010,
  author    = {Probst, M. and Behbahani, Mehdi and Borrmann, E. and Elgeti, S. and Nicolai, M. and Behr, M.},
  title     = {Hemodynamic Modeling for Numerical Analysis and Design of Medical Devices},
  year      = {2010},
  language  = {en}
}
@article{BehbahaniNamWalugaetal.2010,
  author    = {Behbahani, Mehdi and Nam, J. and Waluga, C. and Behr, M. and Pasquali, M. and Mottaghy, K.},
  title     = {Modeling and Numerical Analysis of Platelet Activation, Adhesion and Aggregation in Artificial Organs},
  doi       = {10.1097/01.mat.0000369377.65122.a3},
  year      = {2010},
  language  = {en}
}
@article{JansenBehbahaniLaumenetal.2010,
  author    = {Jansen, S. V. and Behbahani, Mehdi and Laumen, M. and Kaufmann, T. and Hormes, M. and Behr, M. and Schmitz-Rode, T. and Steinseifer, U.},
  title     = {Investigation of Steady Flow Through a Realistic Model of the Thoracic Human Aorta Using 3D Stereo PIV and CFD-Simulation},
  year      = {2010},
  language  = {en}
}
@article{NamAroraBehbahanietal.2010,
  author    = {Nam, J. and Arora, D. and Behbahani, Mehdi and Probst, M. and Benkowski, R. and Behr, M. and Pasquali, M.},
  title     = {New computational method in hemolysis analysis for artificial heart pump},
  year      = {2010},
  language  = {en}
}
@article{GoettscheHoffschmidtSchmitzetal.2010,
  author    = {G{\"o}ttsche, Joachim and Hoffschmidt, Bernhard and Schmitz, Stefan and Sauerborn, Markus},
  title     = {Solar Concentrating Systems Using Small Mirror Arrays},
  series = {Journal of solar energy engineering},
  volume    = {Vol. 132},
  journal   = {Journal of solar energy engineering},
  number    = {Iss. 1},
  isbn      = {0199-6231},
  pages     = {4 S.},
  year      = {2010},
  language  = {en}
}
@article{Hillgaertner2010,
  author    = {Hillg{\"a}rtner, Michael},
  title     = {Normative Regulations},
  series = {ECPE Cluster Seminar EMC in Hybrid and Electric Vehicles : 18 May 2010, Fraunhofer Institute Erlangen},
  journal   = {ECPE Cluster Seminar EMC in Hybrid and Electric Vehicles : 18 May 2010, Fraunhofer Institute Erlangen},
  publisher = {European Center for Power Electronics},
  address   = {N{\"u}rnberg},
  pages     = {1 CD-ROM},
  year      = {2010},
  language  = {en}
}
@article{BoernerFunkeHendricketal.2010,
  author    = {B{\"o}rner, Sebastian and Funke, Harald and Hendrick, P. and Recker, E.},
  title     = {Control system modifications for a hydrogen fuelled gas-turbine},
  series = {ISROMAC 13, 13th International Symposium on Transport Phenomena and Dynamics of Rotating Machinery, Honolulu, HI, US, Apr 4-7, 2010},
  journal   = {ISROMAC 13, 13th International Symposium on Transport Phenomena and Dynamics of Rotating Machinery, Honolulu, HI, US, Apr 4-7, 2010},
  publisher = {Curran},
  address   = {Red Hook, NY},
  isbn      = {978-1-617-38848-4},
  pages     = {665 -- 670},
  year      = {2010},
  language  = {en}
}
@article{BehbahaniProbstMaietal.2010,
  author    = {Behbahani, Mehdi and Probst, M. and Mai, A. and Tran, L. and Vonderstein, K. and Keschenau, P. and Linde, T. and Steinseifer, U. and Behr, M. and Mottaghy, K.},
  title     = {The influence of high shear on thrombosis and hemolysis in artificial organs},
  series = {Artificial Organs},
  volume    = {33},
  journal   = {Artificial Organs},
  number    = {7},
  isbn      = {0391-3988},
  pages     = {426 -- 426},
  year      = {2010},
  language  = {en}
}
@article{JansenBehbahaniLaumenetal.2010,
  author    = {Jansen, Sebastian and Behbahani, Mehdi and Laumen, Marco and Kaufmann, Tim and Hormes, Marcus and Schmitz-Rode, Thomas and Behr, Marek and Steinseifer, Ulrich},
  title     = {3D Stereo-PIV Validation for CFD-Simulation of Steady Flow through the Human Aorta using Rapid-Prototyping techniques},
  year      = {2010},
  language  = {en}
}
@article{MaiwaldDachwald2010,
  author    = {Maiwald, Volker and Dachwald, Bernd},
  title     = {Mission Design for a Multiple-Rendezvous Mission to Jupiter's Trojans},
  pages     = {3},
  year      = {2010},
  language  = {en}
}
@article{GebhardtSchmidtHoetteretal.2010,
  author    = {Gebhardt, Andreas and Schmidt, Frank-Michael and H{\"o}tter, Jan-Steffen and Sokalla, Wolfgang and Sokalla, Patrick},
  title     = {Additive Manufacturing by selective laser melting the realizer desktop machine and its application for the dental industry},
  series = {Physics Procedia},
  volume    = {5},
  journal   = {Physics Procedia},
  number    = {2},
  isbn      = {1875-3892},
  pages     = {543 -- 549},
  year      = {2010},
  language  = {en}
}
@article{GeimerSauerbornHoffschmidtetal.2010,
  author    = {Geimer, Konstantin and Sauerborn, Markus and Hoffschmidt, Bernhard and Schmitz, Mark and G{\"o}ttsche, Joachim},
  title     = {Test Facility for Absorber Specimens of Solar Tower Power Plants},
  series = {Advances in Science and Technology. 74 (2010)},
  journal   = {Advances in Science and Technology. 74 (2010)},
  pages     = {266 -- 271},
  year      = {2010},
  language  = {en}
}
@article{SrivastavaSinghAggarwaletal.2010,
  author    = {Srivastava, A. and Singh, V. and Aggarwal, P. and Schneeweiss, F. and Scherer, Ulrich W. and Friedrich, W.},
  title     = {Optical studies of insulating polymers for radiation dose monitoring},
  series = {Indian Journal of Pure \& Applied Physics},
  volume    = {48},
  journal   = {Indian Journal of Pure \& Applied Physics},
  number    = {11},
  isbn      = {0019-5596},
  pages     = {782 -- 786},
  year      = {2010},
  language  = {en}
}
@article{MiyamotoKanekoMatsuoetal.2010,
  author    = {Miyamoto, Ko-ichiro and Kaneko, Kazumi and Matsuo, Akira and Wagner, Torsten and Kanoh, Shin`ichiro and Sch{\"o}ning, Michael Josef and Yoshinobu, Tatsuo},
  title     = {Miniaturized chemical imaging sensor system using an OLED display panel},
  series = {Procedia Engineering. 5 (2010)},
  journal   = {Procedia Engineering. 5 (2010)},
  isbn      = {1877-7058},
  pages     = {516 -- 519},
  year      = {2010},
  language  = {en}
}
@article{BohrnStuetzFleischeretal.2010,
  author    = {Bohrn, U. and St{\"u}tz, E. and Fleischer, M. and Sch{\"o}ning, Michael Josef},
  title     = {Real-time detection of CO by eukaryotic cells},
  series = {Procedia Engineering. 5 (2010)},
  journal   = {Procedia Engineering. 5 (2010)},
  isbn      = {1877-7058},
  pages     = {17 -- 20},
  year      = {2010},
  language  = {en}
}
@article{WagnerMiyamotoSchoeningetal.2010,
  author    = {Wagner, Torsten and Miyamoto, Ko-ichiro and Sch{\"o}ning, Michael Josef and Yoshinobu, Tatsuo},
  title     = {Novel combination of digital light processing (DLP) and light-addressable potentiometric sensors (LAPS) for flexible chemical imaging},
  series = {Procedia Engineering. 5 (2010)},
  journal   = {Procedia Engineering. 5 (2010)},
  isbn      = {1877-7058},
  pages     = {520 -- 523},
  year      = {2010},
  language  = {en}
}
@article{KirchnerOberlaenderFriedrichetal.2010,
  author    = {Kirchner, Patrick and Oberl{\"a}nder, Jan and Friedrich, Peter and Rysstad, G. and Berger, J. and Keusgen, M. and Sch{\"o}ning, Michael Josef},
  title     = {Realization of a calorimetric gas sensor on polyimide foil for applications in aseptic food industry},
  series = {Procedia Engineering. 5 (2010)},
  journal   = {Procedia Engineering. 5 (2010)},
  isbn      = {1877-7058},
  pages     = {264 -- 267},
  year      = {2010},
  language  = {en}
}
@article{SpelthahnSchaffrathCoppeetal.2010,
  author    = {Spelthahn, Heiko and Schaffrath, Sophie and Coppe, Thomas and Rufi, Frederic and Sch{\"o}ning, Michael Josef},
  title     = {Development of an electrolyte-insulator-semiconductor (EIS) based capacitive heavy metal sensor for the detection of Pb2+ und Cd2+ ions},
  series = {Physica status solidi (a) : applications and material science. 207 (2010), H. 4},
  journal   = {Physica status solidi (a) : applications and material science. 207 (2010), H. 4},
  isbn      = {1862-6300},
  pages     = {930 -- 934},
  year      = {2010},
  language  = {en}
}
@article{GerhardsBelloumBerretzetal.2010,
  author    = {Gerhards, M. and Belloum, A. and Berretz, F. and Sander, Volker and Skorupa, S.},
  title     = {A history-tracing XML-based provenance framework for workflows},
  isbn      = {978-1-4244-8989-3},
  pages     = {1 -- 10},
  year      = {2010},
  language  = {en}
}
@article{BouquegneauKernRousseau2010,
  author    = {Bouquegneau, Christian and Kern, Alexander and Rousseau, Alain},
  title     = {Lightning safety guidelines},
  pages     = {1 -- 6},
  year      = {2010},
  language  = {en}
}
@article{KernFrentzelBehrens2010,
  author    = {Kern, Alexander and Frentzel, Ralf and Behrens, J{\"o}rg},
  title     = {Simulation of the transient voltages in the auxiliary power network of a large power plant in case of a direct lightning strike to the high-voltage overhead transmission line},
  pages     = {749-1 -- 749-7},
  year      = {2010},
  language  = {en}
}
@article{KernKloetersPferdemenges2010,
  author    = {Kern, Alexander and Kl{\"o}ters, Georg and Pferdemenges, J{\"o}rg},
  title     = {Optimised protection against lightning for the signalling and safety systems of level crossings on non-electrified railway lines},
  series = {RTR : European Rail Technology Review},
  volume    = {50},
  journal   = {RTR : European Rail Technology Review},
  number    = {2},
  isbn      = {0079-9548},
  year      = {2010},
  language  = {en}
}
@article{KernSchelthoffMathieu2010,
  author    = {Kern, Alexander and Schelthoff, Christof and Mathieu, Moritz},
  title     = {Probability of lightning strikes to air-terminations of structures using the electro-geometrical model theory and the statistics of lightning current parameters},
  pages     = {750-1 -- 750-8},
  year      = {2010},
  language  = {en}
}
@book{BoonzaaijerHelmigBergerhausenetal.2010,
  author    = {Boonzaaijer, Karel and Helmig, Ilka and Bergerhausen, Johannes and Beudaert, Matthieu},
  title     = {Vision - space for imagination},
  publisher = {Stichting Kunstboek},
  address   = {Oostkamp},
  isbn      = {978-90-5856-357-6},
  pages     = {[85] S. : zahlr. Ill.},
  year      = {2010},
  language  = {en}
}
@article{AbouzarPedrazaSchoeningetal.2010,
  author    = {Abouzar, Maryam H. and Pedraza, A. M. and Sch{\"o}ning, Michael Josef and Poghossian, Arshak},
  title     = {Label-free DNA hybridization and denaturation detection by means of field-effect nanoplate SOI capacitors functionalized with gold nanoparticles},
  series = {Procedia Engineering. 5 (2010)},
  journal   = {Procedia Engineering. 5 (2010)},
  isbn      = {1877-7058},
  pages     = {918 -- 921},
  year      = {2010},
  language  = {en}
}
@article{BerretzSkorupaSanderetal.2010,
  author    = {Berretz, F. and Skorupa, S. and Sander, Volker and Belloum, A.},
  title     = {Towards an actor-driven workflow management system for grids},
  series = {International Symposium on Collaborative Technologies and Systems (CTS), 2010 : 17 - 21 May 2010, Chicago, Illinois, USA / IEEE},
  journal   = {International Symposium on Collaborative Technologies and Systems (CTS), 2010 : 17 - 21 May 2010, Chicago, Illinois, USA / IEEE},
  publisher = {IEEE},
  address   = {Piscataway, NJ},
  isbn      = {978-1-4244-6619-1},
  pages     = {611 -- 616},
  year      = {2010},
  language  = {en}
}
@article{BlomeChiconeHehletal.2010,
  author    = {Blome, Hans-Joachim and Chicone, Carmen and Hehl, Friedrich W. and Mashhoon, Bahram},
  title     = {Nonlocal modification of Newtonian gravity},
  series = {Physical Review D},
  volume    = {81},
  journal   = {Physical Review D},
  number    = {6},
  isbn      = {0556-2821},
  pages     = {065020},
  year      = {2010},
  language  = {en}
}
@article{WagnerWernerMiyamotoetal.2010,
  author    = {Wagner, Torsten and Werner, Frederik and Miyamoto, Ko-ichiro and Ackermann, Hans-Josef and Yoshinobu, Tatsuo and Sch{\"o}ning, Michael Josef},
  title     = {FPGA-based LAPS device for the flexible design of sensing sites on functional interfaces},
  series = {Physica Status Solidi (A). 207 (2010), H. 4},
  journal   = {Physica Status Solidi (A). 207 (2010), H. 4},
  isbn      = {1862-6300},
  pages     = {844 -- 849},
  year      = {2010},
  language  = {en}
}
@article{FredebeulKreinKnoben2010,
  author    = {Fredebeul-Krein, Markus and Knoben, Werner},
  title     = {Long term risk sharing contracts as an approach to establish public-private partnerships for investment into next generation access networks},
  series = {Telecommunications Policy},
  volume    = {34},
  journal   = {Telecommunications Policy},
  number    = {9},
  isbn      = {0308-5961},
  pages     = {528 -- 539},
  year      = {2010},
  language  = {en}
}
@article{ScholzLeyDachwaldetal.2010,
  author    = {Scholz, A. and Ley, Wilfried and Dachwald, Bernd and Miau, J. J. and Juang, J. C.},
  title     = {Flight results of the COMPASS-1 picosatellite mission},
  series = {Acta Astronautica. 67 (2010), H. 9-10},
  journal   = {Acta Astronautica. 67 (2010), H. 9-10},
  isbn      = {0094-5765},
  pages     = {1289 -- 1298},
  year      = {2010},
  language  = {en}
}
@article{HirschfeldLustfeldReisseletal.2010,
  author    = {Hirschfeld, J. A. and Lustfeld, H. and Reißel, Martin and Steffen, B.},
  title     = {A novel scheme for precise diagnostics and effective stabilization of currents in a fuel cell stack},
  series = {International Journal of Energy Research. 34 (2010), H. 3},
  journal   = {International Journal of Energy Research. 34 (2010), H. 3},
  isbn      = {0363-907X},
  pages     = {293 -- 301},
  year      = {2010},
  language  = {en}
}
@article{HirschfeldLustfeldReisseletal.2010,
  author    = {Hirschfeld, J. A. and Lustfeld, H. and Reißel, Martin and Steffen, B.},
  title     = {Tomographic diagnostics of current distributions in a fuel cell stack},
  series = {International Journal of Energy Research},
  volume    = {34},
  journal   = {International Journal of Energy Research},
  number    = {3},
  isbn      = {0363-907X},
  pages     = {284 -- 292},
  year      = {2010},
  language  = {en}
}
@article{StaatSponagelNguyen2010,
  author    = {Staat, Manfred and Sponagel, Stefan and Nguyen, Nhu Huynh},
  title     = {Experiment and material model for soft tissue materials},
  series = {Constitutive models for rubber VI : proceedings of the sixth European Conference on Constitutive Models for Rubber, Dresden, Germany, 7 - 10 September 2009 / eds. Gert Heinrich ...},
  journal   = {Constitutive models for rubber VI : proceedings of the sixth European Conference on Constitutive Models for Rubber, Dresden, Germany, 7 - 10 September 2009 / eds. Gert Heinrich ...},
  publisher = {CRC Press},
  address   = {Boca Raton [u.a.]},
  isbn      = {978-0-415-56327-7},
  pages     = {465 -- 470},
  year      = {2010},
  language  = {en}
}
@article{AlexopoulosHoffschmidt2010,
  author    = {Alexopoulos, Spiros and Hoffschmidt, Bernhard},
  title     = {Solar tower power plant in Germany and future perspectives of the development of the technology in Greece and Cyprus},
  series = {Renewable Energy . 35 (2010), H. 7},
  journal   = {Renewable Energy . 35 (2010), H. 7},
  isbn      = {0960-1481},
  pages     = {1352 -- 1356},
  year      = {2010},
  language  = {en}
}
@article{BalakrishnanAndreiSelmerSelmeretal.2010,
  author    = {Balakrishnan, Karthikeyan and Andrei-Selmer, Luminita-Cornelia and Selmer, Thorsten and Bacher, Michael and Dodel, Richard},
  title     = {Comparison of Intravenous Immunoglobulins for Naturally Occurring Autoantibodies against Amyloid-β},
  series = {Journal of Alzheimer's Disease},
  volume    = {20},
  journal   = {Journal of Alzheimer's Disease},
  number    = {1},
  isbn      = {1387-2877},
  pages     = {135 -- 143},
  year      = {2010},
  language  = {en}
}
@article{NguyenRaatschenStaat2010,
  author    = {Nguyen, N.-H. and Raatschen, Hans-J{\"u}rgen and Staat, Manfred},
  title     = {A hyperelastic model of biological tissue materials in tubular organs},
  pages     = {1 -- 12},
  year      = {2010},
  language  = {en}
}
@article{PhamVuTranetal.2010,
  author    = {Pham, Phu Tinh and Vu, Khoi Duc and Tran, Thanh Ngoc and Staat, Manfred},
  title     = {A primal-dual algorithm for shakedown analysis of elastic-plastic bounded linearly kinematic hardening bodies},
  pages     = {1 -- 7},
  year      = {2010},
  language  = {en}
}
@article{TranStaat2010,
  author    = {Tran, Thanh Ngoc and Staat, Manfred},
  title     = {Shakedown analysis of two dimensional structures by an edge-based smoothed finite element method},
  pages     = {1 -- 7},
  year      = {2010},
  language  = {en}
}
@article{BaeckerPoghossianAbouzaretal.2010,
  author    = {B{\"a}cker, Matthias and Poghossian, Arshak and Abouzar, Maryam H. and Wenmackers, Sylvia and Janssens, Stoffel D. and Haenen, Ken and Wagner, Patrick and Sch{\"o}ning, Michael Josef},
  title     = {Capacitive field-effect (bio-)chemical sensors based on nanocrystalline diamond films},
  series = {Diamond Electronics and Bioelectronics — Fundamentals to Applications III, edited by P. Bergonzo, [u.a.]},
  journal   = {Diamond Electronics and Bioelectronics — Fundamentals to Applications III, edited by P. Bergonzo, [u.a.]},
  pages     = {1 -- 6},
  year      = {2010},
  language  = {en}
}
@article{ReisertHenkelSchneideretal.2010,
  author    = {Reisert, Steffen and Henkel, Hartmut and Schneider, Andreas and Sch{\"a}fer, Daniel and Friedrich, Peter and Berger, J{\"o}rg and Sch{\"o}ning, Michael Josef},
  title     = {Development of a handheld sensor system for the online measurement of hydrogen peroxide in aseptic filling systems},
  series = {Physica Status Solidi (A). 207 (2010), H. 4},
  journal   = {Physica Status Solidi (A). 207 (2010), H. 4},
  isbn      = {1862-6300},
  pages     = {913 -- 918},
  year      = {2010},
  language  = {en}
}
@article{BegingMlynekHataihimakuletal.2010,
  author    = {Beging, Stefan and Mlynek, Daniela and Hataihimakul, Sudkanung and Poghossian, Arshak and Baldsiefen, Gerhard and Busch, Heinz and Laube, Norbert and Kleinen, Lisa and Sch{\"o}ning, Michael Josef},
  title     = {Field-effect calcium sensor for the determination of the risk of urinary stone formation},
  series = {Sensors and Actuators B: Chemical. 144 (2010), H. 2},
  journal   = {Sensors and Actuators B: Chemical. 144 (2010), H. 2},
  pages     = {374 -- 379},
  year      = {2010},
  language  = {en}
}
@article{MiyamotoSugawaraKanohetal.2010,
  author    = {Miyamoto, Ko-ichiro and Sugawara, Yuri and Kanoh, Shin´ichiro and Yoshinobu, Tatsuo and Wagner, Torsten and Sch{\"o}ning, Michael Josef},
  title     = {Image correction method for the chemical imaging sensor},
  series = {Sensors and Actuators B: Chemical. 144 (2010), H. 2},
  journal   = {Sensors and Actuators B: Chemical. 144 (2010), H. 2},
  pages     = {344 -- 348},
  year      = {2010},
  language  = {en}
}
@article{AbouzarPoghossianSiqueiraetal.2010,
  author    = {Abouzar, Maryam H. and Poghossian, Arshak and Siqueira, Jos{\´e} R. Jr. and Oliveira, Osvaldo N. Jr. and Moritz, Werner and Sch{\"o}ning, Michael Josef},
  title     = {Capacitive electrolyte-insulator-semiconductor structures functionalised with a polyelectrolyte/enzyme multilayer: New strategy for enhanced field-effect biosensing},
  series = {Physica Status Solidi (A). 207 (2010), H. 4},
  journal   = {Physica Status Solidi (A). 207 (2010), H. 4},
  isbn      = {1862-6300},
  pages     = {884 -- 890},
  year      = {2010},
  language  = {en}
}
@article{SchoeningKirchnerNgetal.2010,
  author    = {Sch{\"o}ning, Michael Josef and Kirchner, Patrick and Ng, Yue Ann and Spelthahn, Heiko and Schneider, Andreas and Henkel, Hartmut and Friedrich, Peter and Kolstad, Jens and Berger, J{\"o}rg and Keusgen, Michael},
  title     = {Gas sensor investigation based on a catalytically activated thin-film thermopile for H2O2 detection},
  series = {Physica Status Solidi (A). 207 (2010), H. 4},
  journal   = {Physica Status Solidi (A). 207 (2010), H. 4},
  isbn      = {1862-6300},
  pages     = {787 -- 792},
  year      = {2010},
  language  = {en}
}
@article{TurekHeidenGuoetal.2010,
  author    = {Turek, Monik and Heiden, Wolfgang and Guo, Sharon and Riesen, Alfred and Schubert, J{\"u}rgen and Zander, Willi and Kr{\"u}ger, Peter and Keusgen, Michael and Sch{\"o}ning, Michael Josef},
  title     = {Simultaneous detection of cyanide and heavy metals for environmental analysis by means of µISEs},
  series = {Physica Status Solidi (A). 207 (2010), H. 4},
  journal   = {Physica Status Solidi (A). 207 (2010), H. 4},
  isbn      = {1862-6300},
  pages     = {817 -- 823},
  year      = {2010},
  language  = {en}
}
@article{BuniatyanAbouzarMartirosyanetal.2010,
  author    = {Buniatyan, Vahe V. and Abouzar, Maryam H. and Martirosyan, Norayr W. and Schubert, J{\"u}rgen and Gevorgian, Spartak and Sch{\"o}ning, Michael Josef and Poghossian, Arshak},
  title     = {pH-sensitive properties of barium strontium titanate (BST) thin films prepared by pulsed laser deposition technique},
  series = {Physica Status Solidi (A). 207 (2010), H. 4},
  journal   = {Physica Status Solidi (A). 207 (2010), H. 4},
  isbn      = {1862-6300},
  pages     = {824 -- 830},
  year      = {2010},
  language  = {en}
}
@article{UllrichGrottkeRossaintetal.2010,
  author    = {Ullrich, Sebastian and Grottke, Oliver and Rossaint, Rolf and Staat, Manfred and Deserno, Thomas M. and Kuhlen, Torsten},
  title     = {Virtual Needle Simulation with Haptics for Regional Anaesthesia},
  pages     = {1 -- 3},
  year      = {2010},
  language  = {en}
}