@article{AlebouyehSamamiPieperBreitbachetal.2014,
  author    = {Alebouyeh Samami, Behzad and Pieper, Martin and Breitbach, Gerd and Hodapp, Josef},
  title     = {Heat production in the windings of the stators of electric machines under stationary condition},
  series = {Heat and mass transfer},
  volume    = {50},
  journal   = {Heat and mass transfer},
  publisher = {Springer},
  address   = {Heidelberg},
  issn      = {0947-7411 (Print) ; 1432-1181 (E-Journal)},
  doi       = {10.1007/s00231-014-1371-8},
  pages     = {1707 -- 1716},
  year      = {2014},
  abstract  = {In electric machines due to high currents and resistive losses (joule heating) heat is produced. To avoid damages by overheating the design of effective cooling systems is required. Therefore the knowledge of heat sources and heat transfer processes is necessary. The purpose of this paper is to illustrate a good and effective calculation method for the temperature analysis based on homogenization techniques. These methods have been applied for the stator windings in a slot of an electric machine consisting of copper wires and resin. The key quantity here is an effective thermal conductivity, which characterizes the heterogeneous wire resin-arrangement inside the stator slot. To illustrate the applicability of the method, the analysis of a simplified, homogenized model is compared with the detailed analysis of temperature behavior inside a slot of an electric machine according to the heat generation. We considered here only the stationary situation. The achieved numerical results are accurate and show that the applied homogenization technique works in practice. Finally the results of simulations for the two cases, the original model of the slot and the homogenized model chosen for the slot (unit cell), are compared to experimental results.},
  language  = {en}
}
@article{AlexopoulosBreitbachHoffschmidtetal.2008,
  author    = {Alexopoulos, Spiros and Breitbach, Gerd and Hoffschmidt, Bernhard and Stobbe, P.},
  title     = {Computational fluid flow of porous resic ceramic filtering modules and optimization of the channel edge form geometry},
  series = {Proceedings : April 14 - 18, 2008, Leipzig, Germany / hosted by VDI, Society for Chemical and Process Engineering . Vol 2},
  journal   = {Proceedings : April 14 - 18, 2008, Leipzig, Germany / hosted by VDI, Society for Chemical and Process Engineering . Vol 2},
  publisher = {Filtech Exhibitions},
  address   = {Meerbusch},
  pages     = {300 -- 304},
  year      = {2008},
  language  = {en}
}
@article{AlexopoulosBreitbachHoffschmidtetal.2008,
  author    = {Alexopoulos, Spiros and Breitbach, Gerd and Hoffschmidt, Bernhard and Stobbe, P.},
  title     = {Optimization of the geometry of porous SiC ceramic filtering modules using numerical methods},
  series = {Developments in porous, biological and geopolymer ceramics : a collection of papers presented at the 31st International Conference on Advanced Ceramics and Composites, January 21 - 26, 2007, Daytona Beach, Florida ; [papers presented at the Symposium on Porous Ceramics: Novel Developments and Applications] / ed.: Manuel Brito ... Vol. ed.: Jonathan Salem ... The American Ceramics Society},
  journal   = {Developments in porous, biological and geopolymer ceramics : a collection of papers presented at the 31st International Conference on Advanced Ceramics and Composites, January 21 - 26, 2007, Daytona Beach, Florida ; [papers presented at the Symposium on Porous Ceramics: Novel Developments and Applications] / ed.: Manuel Brito ... Vol. ed.: Jonathan Salem ... The American Ceramics Society},
  publisher = {Wiley},
  address   = {Hoboken, NJ},
  isbn      = {9780470196403},
  pages     = {95 -- 104},
  year      = {2008},
  language  = {en}
}
@article{AlexopoulosHoffschmidt2010,
  author    = {Alexopoulos, Spiros and Hoffschmidt, Bernhard},
  title     = {Solar tower power plant in Germany and future perspectives of the development of the technology in Greece and Cyprus},
  series = {Renewable Energy . 35 (2010), H. 7},
  journal   = {Renewable Energy . 35 (2010), H. 7},
  isbn      = {0960-1481},
  pages     = {1352 -- 1356},
  year      = {2010},
  language  = {en}
}
@article{AlexopoulosHoffschmidt2017,
  author    = {Alexopoulos, Spiros and Hoffschmidt, Bernhard},
  title     = {Advances in solar tower technology},
  series = {Wiley interdisciplinary reviews : Energy and Environment : WIREs},
  volume    = {6},
  journal   = {Wiley interdisciplinary reviews : Energy and Environment : WIREs},
  number    = {1},
  publisher = {Wiley},
  address   = {Weinheim},
  issn      = {2041-840X},
  doi       = {10.1002/wene.217},
  pages     = {1 -- 19},
  year      = {2017},
  language  = {en}
}
@article{ArpshofenPoolSommeretal.1983,
  author    = {Arpshofen, Ingo and Pool, M. J. and Sommer, Ferdinand and Gerling, Ulrich and Predel, Bruno and Schultheiss, Emil},
  title     = {Determination of the integral mixing enthalpies in the Cu-Pd-Si liquid ternary alloy system at 1600 K},
  series = {Zeitschrift f{\"u}r Metallkunde : international journal of materials research and advanced techniques. Bd. 74, H. 1},
  journal   = {Zeitschrift f{\"u}r Metallkunde : international journal of materials research and advanced techniques. Bd. 74, H. 1},
  issn      = {0044-3093 ; 0179-4841},
  pages     = {25 -- 32},
  year      = {1983},
  language  = {en}
}
@article{BalewskiBrauksiepeHardt1997,
  author    = {Balewski, J. and Brauksiepe, S. and Hardt, Arno},
  title     = {Threshold measurements at the internal experimental facility COSY-11 / J. Balewski [u.a.]},
  series = {Nuclear physics A. Vol. 626, iss. 1-2},
  journal   = {Nuclear physics A. Vol. 626, iss. 1-2},
  issn      = {1873-1554 (E-Journal) ; 0375-9474 (Print)},
  pages     = {85 -- 92},
  year      = {1997},
  language  = {en}
}
@article{BansalMuellerVieiraetal.2000,
  author    = {Bansal, N. K. and M{\"u}ller, C. and Vieira, M. E. and Faber, Christian and Schwarzer, Klemens},
  title     = {Thermal performance of a rock bed storage system},
  series = {Proceedings : University of Stuttgart, Germany, August 28th until September 1st, 2000 / Terrastock 2000, 8th International Conference on Thermal Energy Storage. Ed.: M. Benner ... - Vol. 1},
  journal   = {Proceedings : University of Stuttgart, Germany, August 28th until September 1st, 2000 / Terrastock 2000, 8th International Conference on Thermal Energy Storage. Ed.: M. Benner ... - Vol. 1},
  publisher = {Inst. f{\"u}r Thermodynamik und W{\"a}rmetechnik},
  address   = {Stuttgart},
  isbn      = {3-9805274-1-7},
  pages     = {433 -- 439},
  year      = {2000},
  language  = {en}
}
@article{BarsovBechstedtHardt2001,
  author    = {Barsov, S. and Bechstedt, U. and Hardt, Arno},
  title     = {ANKE, a new facility for medium energy hadron physics at COSY-J{\"u}lich / S. Barsov [u.a.]},
  series = {Nuclear instruments and methods in Physics Research Section A: Accelerators, Spectrometers, Detectors and Associated Equipment. Vol. 462, iss. 3},
  journal   = {Nuclear instruments and methods in Physics Research Section A: Accelerators, Spectrometers, Detectors and Associated Equipment. Vol. 462, iss. 3},
  issn      = {0167-5087 (Print) ; 0168-9002 (E-journal)},
  pages     = {364 -- 381},
  year      = {2001},
  language  = {en}
}
@article{BaumgartnerFidlerWethetal.2008,
  author    = {Baumgartner, Werner and Fidler, Florian and Weth, Agnes and Habbecke, Martin and Jakob, Peter and Butenweg, Christoph and B{\"o}hme, Wolfgang},
  title     = {Investigating the locomotion of the sandfish in desert sand using NMR-Imaging},
  series = {PLOS ONE},
  volume    = {3},
  journal   = {PLOS ONE},
  number    = {10},
  publisher = {Plos},
  address   = {San Francisco, California, US},
  issn      = {1932-6203},
  doi       = {10.1371/journal.pone.0003309},
  pages     = {e3309},
  year      = {2008},
  abstract  = {The sandfish (Scincus scincus) is a lizard having the remarkable ability to move through desert sand for significant distances. It is well adapted to living in loose sand by virtue of a combination of morphological and behavioural specializations. We investigated the bodyform of the sandfish using 3D-laserscanning and explored its locomotion in loose desert sand using fast nuclear magnetic resonance (NMR) imaging. The sandfish exhibits an in-plane meandering motion with a frequency of about 3 Hz and an amplitude of about half its body length accompanied by swimming-like (or trotting) movements of its limbs. No torsion of the body was observed, a movement required for a digging-behaviour. Simple calculations based on the Janssen model for granular material related to our findings on bodyform and locomotor behaviour render a local decompaction of the sand surrounding the moving sandfish very likely. Thus the sand locally behaves as a viscous fluid and not as a solid material. In this fluidised sand the sandfish is able to "swim" using its limbs.},
  language  = {en}
}
@article{BechstedtHaasHackeretal.1985,
  author    = {Bechstedt, U. and Haas, H. and Hacker, U. and Hardt, Arno and Henn, K. and Martin, S. and Wimmer, J.},
  title     = {Magnets for the German Spallation Source SNQ},
  series = {IEEE transactions on nuclear science. Vol. 32, iss. 5},
  journal   = {IEEE transactions on nuclear science. Vol. 32, iss. 5},
  issn      = {1558-1578 (E-Journal); 0018-9499 (Print)},
  pages     = {3631 -- 3633},
  year      = {1985},
  language  = {en}
}
@article{BeckerFrauenrathHezeletal.2010,
  author    = {Becker, Meike and Frauenrath, Tobias and Hezel, Fabian and Krombach, Gabriele A. and Kremer, Ute and Koppers, Benedikt and Butenweg, Christoph and Goemmel, Andreas and Utting, Jane F. and Schulz-Menger, Jeanette and Niendorf, Thoralf},
  title     = {Comparison of left ventricular function assessment using phonocardiogram- and electrocardiogram-triggered 2D SSFP CINE MR imaging at 1.5 T and 3.0 T},
  series = {European Radiology},
  volume    = {20},
  journal   = {European Radiology},
  publisher = {Springer},
  address   = {Berlin},
  issn      = {1432-1084 (Onlineausgabe)},
  doi       = {10.1007/s00330-009-1676-z},
  pages     = {1344 -- 1355},
  year      = {2010},
  abstract  = {Objective: As high-field cardiac MRI (CMR) becomes more widespread the propensity of ECG to interference from electromagnetic fields (EMF) and to magneto-hydrodynamic (MHD) effects increases and with it the motivation for a CMR triggering alternative. This study explores the suitability of acoustic cardiac triggering (ACT) for left ventricular (LV) function assessment in healthy subjects (n=14). Methods: Quantitative analysis of 2D CINE steady-state free precession (SSFP) images was conducted to compare ACT's performance with vector ECG (VCG). Endocardial border sharpness (EBS) was examined paralleled by quantitative LV function assessment. Results: Unlike VCG, ACT provided signal traces free of interference from EMF or MHD effects. In the case of correct Rwave recognition, VCG-triggered 2D CINE SSFP was immune to cardiac motion effects—even at 3.0 T. However, VCG-triggered 2D SSFP CINE imaging was prone to cardiac motion and EBS degradation if R-wave misregistration occurred. ACT-triggered acquisitions yielded LV parameters (end-diastolic volume (EDV), endsystolic volume (ESV), stroke volume (SV), ejection fraction (EF) and left ventricular mass (LVM)) comparable with those derived fromVCG-triggered acquisitions (1.5 T: ESVVCG=(56± 17) ml, EDVVCG=(151±32)ml, LVMVCG=(97±27) g, SVVCG=(94± 19)ml, EFVCG=(63±5)\% cf. ESVACT= (56±18) ml, EDVACT=(147±36) ml, LVMACT=(102±29) g, SVACT=(91± 22) ml, EFACT=(62±6)\%; 3.0 T: ESVVCG=(55±21) ml, EDVVCG=(151±32) ml, LVMVCG=(101±27) g, SVVCG=(96±15) ml, EFVCG=(65±7)\% cf. ESVACT=(54±20) ml, EDVACT=(146±35) ml, LVMACT= (101±30) g, SVACT=(92±17) ml, EFACT=(64±6)\%). Conclusions: ACT's intrinsic insensitivity to interference from electromagnetic fields renders},
  language  = {en}
}
@article{BergPostweilerSteuerDankertLeichtScholten2023,
  author    = {Berg-Postweiler, Julia and Steuer-Dankert, Linda and Leicht-Scholten, Carmen},
  title     = {One size does not fit all: Applying antibias trainings in academia},
  series = {The International Journal of Organizational Diversity},
  volume    = {24},
  journal   = {The International Journal of Organizational Diversity},
  number    = {1},
  publisher = {Common Ground Research Networks},
  issn      = {2328-6261 (Print)},
  doi       = {10.18848/2328-6261/CGP/v24i01/1-23},
  pages     = {1 -- 23},
  year      = {2023},
  abstract  = {Antibias training is increasingly demanded and practiced in academia and industry to increase employees' sensitivity to discrimination, racism, and diversity. Under the heading of "Diversity Management," antibias trainings are mainly offered as one-off workshops intending to raise awareness of unconscious biases, create a diversity-affirming corporate culture, promote awareness of the potential of diversity, and ultimately enable the reflection of diversity in development processes. However, coming from childhood education, research and scientific articles on the sustainable effectiveness of antibias in adulthood, especially in academia, are very scarce. In order to fill this research gap, the article aims to explore how sustainable the effects of individual antibias trainings on participants' behavior are. In order to investigate this, participant observation in a qualitative pre-post setting was conducted, analyzing antibias training in an academic context. Two observers actively participated in the training sessions and documented the activities and reflection processes of the participants. Overall, the results question the effectiveness of single antibias trainings and show that a target-group adaptive approach is mandatory owing to the background of the approach in early childhood education. Therefore, antibias work needs to be adapted to the target group's needs and realities of life. Furthermore, the study reveals that single antibias trainings must be embedded in a holistic diversity management approach to stimulate sustainable reflection processes among the target group. This article is one of the first to scientifically evaluate antibias training effectiveness, especially in engineering sciences and the university context.},
  language  = {en}
}
@article{BlankeHagenkampDoeringetal.2021,
  author    = {Blanke, Tobias and Hagenkamp, Markus and D{\"o}ring, Bernd and G{\"o}ttsche, Joachim and Reger, Vitali and Kuhnhenne, Markus},
  title     = {Net-exergetic, hydraulic and thermal optimization of coaxial heat exchangers using fixed flow conditions instead of fixed flow rates},
  series = {Geothermal Energy},
  volume    = {9},
  journal   = {Geothermal Energy},
  number    = {Article number: 19},
  publisher = {Springer},
  address   = {Berlin},
  issn      = {2195-9706},
  doi       = {10.1186/s40517-021-00201-3},
  pages     = {23 Seiten},
  year      = {2021},
  abstract  = {Previous studies optimized the dimensions of coaxial heat exchangers using constant mass fow rates as a boundary condition. They show a thermal optimal circular ring width of nearly zero. Hydraulically optimal is an inner to outer pipe radius ratio of 0.65 for turbulent and 0.68 for laminar fow types. In contrast, in this study, fow conditions in the circular ring are kept constant (a set of fxed Reynolds numbers) during optimization. This approach ensures fxed fow conditions and prevents inappropriately high or low mass fow rates. The optimization is carried out for three objectives: Maximum energy gain, minimum hydraulic efort and eventually optimum net-exergy balance. The optimization changes the inner pipe radius and mass fow rate but not the Reynolds number of the circular ring. The thermal calculations base on Hellstr{\"o}m's borehole resistance and the hydraulic optimization on individually calculated linear loss of head coefcients. Increasing the inner pipe radius results in decreased hydraulic losses in the inner pipe but increased losses in the circular ring. The net-exergy diference is a key performance indicator and combines thermal and hydraulic calculations. It is the difference between thermal exergy fux and hydraulic efort. The Reynolds number in the circular ring is instead of the mass fow rate constant during all optimizations. The result from a thermal perspective is an optimal width of the circular ring of nearly zero. The hydraulically optimal inner pipe radius is 54\% of the outer pipe radius for laminar fow and 60\% for turbulent fow scenarios. Net-exergetic optimization shows a predominant infuence of hydraulic losses, especially for small temperature gains. The exact result depends on the earth's thermal properties and the fow type. Conclusively, coaxial geothermal probes' design should focus on the hydraulic optimum and take the thermal optimum as a secondary criterion due to the dominating hydraulics.},
  language  = {en}
}
@article{BouquegneauKernRousseau2010,
  author    = {Bouquegneau, Christian and Kern, Alexander and Rousseau, Alain},
  title     = {Lightning safety guidelines},
  pages     = {1 -- 6},
  year      = {2010},
  language  = {en}
}
@article{BreitbachDeschkaAkiba1992,
  author    = {Breitbach, Gerd and Deschka, S. and Akiba, M.},
  title     = {High heat flux tests on brazed divertor components in electron and ion beam test facilities / S. Deschka ; M. Akiba ; G. Breitbach ...},
  series = {International journal of refractory metals and hard materials. 11 (1992), H. 6},
  journal   = {International journal of refractory metals and hard materials. 11 (1992), H. 6},
  isbn      = {0263-4368},
  pages     = {367 -- 375},
  year      = {1992},
  language  = {en}
}
@article{BreitbachSchmidtPlutkaSchubertetal.1993,
  author    = {Breitbach, Gerd and Schmidt-Plutka, A. and Schubert, F. and Nickel, H.},
  title     = {Deformation behaviour of structures exposed at very high temperatures to cyclic thermal and mechanical loadings},
  series = {Structural mechanics in reactor technology : transactions of the 12th International Conference on Structural Mechanics in Reactor Technology, Stuttgart, Germany, 15-20 August 1993 / ed. Karl F. Kussmaul. - Bd. L : Inelastic behaviour of solids and structures},
  journal   = {Structural mechanics in reactor technology : transactions of the 12th International Conference on Structural Mechanics in Reactor Technology, Stuttgart, Germany, 15-20 August 1993 / ed. Karl F. Kussmaul. - Bd. L : Inelastic behaviour of solids and structures},
  publisher = {Elsevier},
  address   = {Amsterdam [u.a.]},
  isbn      = {0-444-81515-5},
  pages     = {203 -- 208},
  year      = {1993},
  language  = {en}
}
@article{BreitbachSchubert2004,
  author    = {Breitbach, Gerd and Schubert, F.},
  title     = {A contribution to stress prediction in coatings for gas turbine blades},
  series = {Archive of applied mechanics. 73 (2004), H. 9-10},
  journal   = {Archive of applied mechanics. 73 (2004), H. 9-10},
  isbn      = {0939-1533},
  pages     = {682 -- 689},
  year      = {2004},
  language  = {en}
}
@article{BreitbachWolfDeschkaetal.1992,
  author    = {Breitbach, Gerd and Wolf, U. and Deschka, S. and Nickel, H.},
  title     = {Thermomechanical analysis of an actively cooled divertor mock up},
  series = {Tagungsbericht : Jahrestagung Kerntechnik : Stadthalle Karlsruhe, 5.-7. Mai 1992, Karlsruhe = Proceedings / Kerntechnische Gesellschaft ... [Red.: Karl G. Bauer]. - 1. Aufl., als Ms. gedr..},
  journal   = {Tagungsbericht : Jahrestagung Kerntechnik : Stadthalle Karlsruhe, 5.-7. Mai 1992, Karlsruhe = Proceedings / Kerntechnische Gesellschaft ... [Red.: Karl G. Bauer]. - 1. Aufl., als Ms. gedr..},
  publisher = {INFOFORUM},
  address   = {Bonn},
  pages     = {457 -- 461},
  year      = {1992},
  language  = {en}
}
@article{Bruessermann1989,
  author    = {Br{\"u}ssermann, Klaus},
  title     = {H3 and C14 air monitoring according to KTA 1503.1},
  series = {2. Karlsruhe international conference on analytical chemistry in nuclear technology, Karlsruhe (Germany), 5-9 Jun 1989},
  journal   = {2. Karlsruhe international conference on analytical chemistry in nuclear technology, Karlsruhe (Germany), 5-9 Jun 1989},
  pages     = {223},
  year      = {1989},
  language  = {en}
}