@article{ReisgenSchleserMokrovetal.2010,
  author    = {Reisgen, Uwe and Schleser, Markus and Mokrov, Oleg and Ahmed, Essam},
  title     = {Shielding gas influences on laser weldability of tailored blanks of advanced automotive steels},
  series = {Applied surface science},
  volume    = {257},
  journal   = {Applied surface science},
  number    = {5},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0169-4332 (E-Journal); 0169-4332 (Print)},
  doi       = {10.1016/j.apsusc.2010.08.042},
  pages     = {1401 -- 1406},
  year      = {2010},
  abstract  = {The effects of shielding gas types and flow rates on CO2 laser weldability of DP600/TRIP700 steel sheets were studied in this work. The evaluated shielding gases were helium (He), argon (Ar) and different mixtures of He and Ar. Weld penetration, tensile strength and formability (Erichsen test) of laser welds were found to be strongly dependent upon the shielding gas types. The ability of shielding gas in removing plasma plume and thus increasing weld penetration is believed to be closely related to ionization potential and atomic weight which determine the period of plasma formation and disappearance. It was found that the higher helium shielding gas flow rate, the deeper weld penetration and the lower weld width.},
  language  = {en}
}
@article{GebhardtMatharPlum1994,
  author    = {Gebhardt, Andreas and Mathar, W. and Plum, H.-D.},
  title     = {SFM-System Stereolithographie und selektives Lasersintern im Vergleich},
  pages     = {85 -- 95},
  year      = {1994},
  language  = {de}
}
@article{KaemperBergBegemannetal.1998,
  author    = {K{\"a}mper, Klaus-Peter and Berg, U. and Begemann, M. and Hagemann, B. (u.a.)},
  title     = {Series production and testing of a micro motor. Serienfertigung und Pr{\"u}fung eines Mikromotors},
  series = {Actuator 98 : 6th International Conference on New Actuators ; 17 - 19 June, 1998, Bremen, Germany ; conference proceedings / ed.: Hubert Borgmann ...},
  journal   = {Actuator 98 : 6th International Conference on New Actuators ; 17 - 19 June, 1998, Bremen, Germany ; conference proceedings / ed.: Hubert Borgmann ...},
  publisher = {Messe Bremen},
  address   = {Bremen},
  isbn      = {3-933339-00-6},
  pages     = {552 -- 555},
  year      = {1998},
  language  = {en}
}
@article{GebhardtMatharPlumetal.1996,
  author    = {Gebhardt, Andreas and Mathar, W. and Plum, H-D. and Wolf, M.},
  title     = {Serienqualit{\"a}t und -st{\"u}ckzahlen durch Abformprozesse},
  pages     = {147 -- 159},
  year      = {1996},
  language  = {de}
}
@article{StarkeDrews1992,
  author    = {Starke, G{\"u}nther and Drews, P.},
  title     = {Sensorik f{\"u}r das Schutzgasschweißen mit Robotern},
  series = {DVS-Berichte. 143 (1992)},
  journal   = {DVS-Berichte. 143 (1992)},
  isbn      = {0418-9639},
  pages     = {62 -- 66},
  year      = {1992},
  language  = {de}
}
@article{StarkeDrews1985,
  author    = {Starke, G{\"u}nther and Drews, P.},
  title     = {Sensoren in der Schweisstechnik},
  series = {Die Umschau. 84 (1985), H. 5},
  journal   = {Die Umschau. 84 (1985), H. 5},
  isbn      = {0041-6347},
  pages     = {296 -- 300},
  year      = {1985},
  language  = {de}
}
@article{StarkeBeckmannRogosetal.1987,
  author    = {Starke, G{\"u}nther and Beckmann, L.-H. and Rogos, J. and Schmall, K-H. (u.a.)},
  title     = {Sensoren in der automatisierten Schweisstechnik},
  pages     = {61 -- 147},
  year      = {1987},
  language  = {de}
}
@article{Starke1986,
  author    = {Starke, G{\"u}nther},
  title     = {Sensoren fuer Schutzgasschweissroboter: Problemstellung, Funktionsweise, Handhabung und Programmierung von praxiserprobten Systemen},
  pages     = {1 -- 22},
  year      = {1986},
  language  = {de}
}
@article{RieperGebhardtStucker2016,
  author    = {Rieper, Harald and Gebhardt, Andreas and Stucker, Brent},
  title     = {Selective Laser Melting of the Eutectic Silver-Copper Alloy Ag 28 wt \% Cu},
  series = {RTejournal - Forum f{\"u}r Rapid Technologie},
  volume    = {13},
  journal   = {RTejournal - Forum f{\"u}r Rapid Technologie},
  issn      = {1614-0923},
  url       = {http://nbn-resolving.de/nbn:de:0009-2-44141},
  year      = {2016},
  abstract  = {The aim of this work was to perform a detailed investigation of the use of Selective Laser Melting (SLM) technology to process eutectic silver-copper alloy Ag 28 wt. \% Cu (also called AgCu28). The processing occurred with a Realizer SLM 50 desktop machine. The powder analysis (SEM-topography, EDX, particle distribution) was reported as well as the absorption rates for the near-infrared (NIR) spectrum. Microscope imaging showed the surface topography of the manufactured parts. Furthermore, microsections were conducted for the analysis of porosity. The Design of Experiments approach used the response surface method in order to model the statistical relationship between laser power, spot distance and pulse time.},
  language  = {en}
}
@article{FateriGebhardt2015,
  author    = {Fateri, Miranda and Gebhardt, Andreas},
  title     = {Selective Laser Melting of Soda-Lime Glass Powder},
  series = {International Journal of Applied Ceramic Technology},
  volume    = {12},
  journal   = {International Journal of Applied Ceramic Technology},
  number    = {1},
  publisher = {Wiley-Blackwell},
  address   = {Oxford},
  issn      = {1744-7402},
  doi       = {10.1111/ijac.12338},
  pages     = {53 -- 61},
  year      = {2015},
  language  = {en}
}
@article{HoetterFateriGebhardt2012,
  author    = {H{\"o}tter, Jan-Steffen and Fateri, Miranda and Gebhardt, Andreas},
  title     = {Selective laser melting of metals: desktop machines open up new chances even for small companies},
  series = {Advanced materials research},
  volume    = {622-623},
  journal   = {Advanced materials research},
  publisher = {Trans Tech Publ.},
  address   = {Baech},
  issn      = {1662-8985 (E-Journal); 1022-6680 (Print)},
  doi       = {10.4028/www.scientific.net/AMR.622-623.461},
  pages     = {461 -- 465},
  year      = {2012},
  abstract  = {Additive manufacturing (AM) of metal parts by using Selective Laser Melting (SLM) has become a powerful tool mostly in the area of automotive, aerospace engineering and others. Especially in the field of dentistry, jewelry and related branches that require individualized or even one-of-a-kind products, the direct digital manufacturing process opens up new ways of design and manufacturing. In these fields, mostly small and medium sized businesses (SME) are operating which do not have sufficient human and economic resources to invest in this technology. But to stay competitive, the application of AM can be regarded as a necessity. In this situation a new desktop machine (Realizer SLM 50) was introduced that cost about 1/3 of a shop floor SLM machine and promises small quality parts. To find out whether the machine really is an alternative for SMEs the University of Applied Science, Aachen, Germany, designed, build and optimized typical parts from the dentistry and the jewelry branches using CoCr and silver material, the latter being new with this application. The paper describes the SLM procedure and how to find and optimize the most important parameters. The test is accompanied by digital simulation in order to verify the build parameters and to plan future builds. The procedure is shown as well as the resulting parts made from CoCr and silver material.},
  language  = {en}
}
@article{EnningDollsBrunberg2009,
  author    = {Enning, Manfred and Dolls, S. and Brunberg, A.},
  title     = {Selbsteinstellverfahren f{\"u}r Temperiervorrichtungen mit Außenverrohrung / Dolls, S. ; Enning, M. ; Brunberg, A. ; Abel, D.},
  series = {Automation 2009 : Automatisierungskongress in Deutschland ; Kongress Baden-Baden, 16. und 17. Juni 2009 / VDI-VDE-Gesellschaft Mess- und Automatisierungstechnik},
  journal   = {Automation 2009 : Automatisierungskongress in Deutschland ; Kongress Baden-Baden, 16. und 17. Juni 2009 / VDI-VDE-Gesellschaft Mess- und Automatisierungstechnik},
  publisher = {VDI-Verl.},
  address   = {D{\"u}sseldorf},
  isbn      = {978-3-18-092067-2},
  pages     = {429 -- 432},
  year      = {2009},
  language  = {de}
}
@article{Benner1989,
  author    = {Benner, Joachim},
  title     = {Schwingungsbelastung von drehzahlgeregelten Antrieben mit Stromrichtermotoren},
  series = {Antriebstechnik : Konstruktion, Entwicklung und Anwendung von Antrieben und Steuerungen ; Organ der Forschungsvereinigung Antriebstechnik e.V.},
  volume    = {28},
  journal   = {Antriebstechnik : Konstruktion, Entwicklung und Anwendung von Antrieben und Steuerungen ; Organ der Forschungsvereinigung Antriebstechnik e.V.},
  number    = {12},
  publisher = {Vereinigte Fachverl.},
  address   = {Mainz},
  issn      = {0341-2652},
  pages     = {49 -- 54},
  year      = {1989},
  language  = {de}
}
@article{StarkeStrunzSpiess1995,
  author    = {Starke, G{\"u}nther and Strunz, U. and Spieß, C.},
  title     = {Schweißprozeßparameteroptimierung mit Fuzzy-Logik},
  series = {Schweißen und Schneiden. 47 (1995), H. 6},
  journal   = {Schweißen und Schneiden. 47 (1995), H. 6},
  isbn      = {0036-7184},
  pages     = {494 -- 503},
  year      = {1995},
  language  = {de}
}
@article{GebhardtGuntermannHaeming1997,
  author    = {Gebhardt, Andreas and Guntermann, P. and H{\"a}ming, L.},
  title     = {Schweißen mit dem Nd:YAG-Laser},
  series = {Der Praktiker, Schweißen und Schneiden. 49 (1997), H. 4},
  journal   = {Der Praktiker, Schweißen und Schneiden. 49 (1997), H. 4},
  isbn      = {0554-9965},
  pages     = {170 -- 172},
  year      = {1997},
  language  = {de}
}
@article{Gebhardt1999,
  author    = {Gebhardt, Andreas},
  title     = {Schnell und flexibel zur Kleinserie. Effizienzsteigerung bei der Realisierung von Komponenten und Teilsystemen},
  series = {Ingenieur-Werkstoffe. 8 (1999), H. 3},
  journal   = {Ingenieur-Werkstoffe. 8 (1999), H. 3},
  isbn      = {0935-5715},
  pages     = {8 -- 14},
  year      = {1999},
  language  = {de}
}
@article{Wollert1999,
  author    = {Wollert, J{\"o}rg},
  title     = {Schlaue Produktion von smarten Autos : hinter der Smart-Produktion steckt ein innovatives Logistikkonzept},
  series = {Technica},
  volume    = {Bd. 48},
  journal   = {Technica},
  number    = {H. 4},
  issn      = {0040-866X},
  pages     = {20 -- 23},
  year      = {1999},
  language  = {de}
}
@article{BabilonWilbringTappertetal.2018,
  author    = {Babilon, Katharina and Wilbring, Daniela and Tappert, Tim and Pfaff, Raphael and Enning, Manfred},
  title     = {Schienenfahrzeugtechnik hands on - FH Aachen IMechE Railway Challenge},
  series = {Ingenieurspiegel},
  journal   = {Ingenieurspiegel},
  number    = {2},
  publisher = {Public Verlag},
  address   = {Bingen},
  issn      = {1868-5919},
  pages     = {20 -- 22},
  year      = {2018},
  language  = {de}
}
@article{GebhardtBrueckerSchmidt2005,
  author    = {Gebhardt, Andreas and Br{\"u}cker, Christoph and Schmidt, Frank-Michael},
  title     = {RP gest{\"u}tzte Herstellung komplexer transparenter Hohlr{\"a}ume f{\"u}r die Str{\"o}mungsanalyse},
  year      = {2005},
  abstract  = {Die Berechnung der Durchstr{\"o}mung von Bauteilen ist gegen{\"u}ber derjenigen von umstr{\"o}mten Bauteilen deutlich im Hintertreffen. Das liegt vor allem an der fehlenden Verf{\"u}gbarkeit geeigneter optisch transparenter Modellkan{\"a}le f{\"u}r die experimentelle Analyse. Der Beitrag stellt ein Verfahren zur Herstellung transparenter durchstr{\"o}mter Geometrien auf der Basis generativ gefertigter Urmodelle vor. Damit k{\"o}nnen beliebig komplexe Innenstr{\"o}mungen optisch analysiert werden. Anhand von zwei Beispielen aus der Medizin, der Modellierung der oberen Atemwege und des Bronchialbaums, wird das Verfahren vorgef{\"u}hrt. Der generative Bauprozess mittels 3D-Printing wird beschrieben und die Abformung in transparentem Silikon gezeigt. Schließlich werden beispielhaft der Messaufbau und Ergebnisse der Anwendung vorgestellt. Das Verfahren bildet die Grundlage f{\"u}r die Analyse und Berechnung komplexer Innenstr{\"o}mungen und tr{\"a}gt somit zur Verbesserung zahlreicher technischer Anwendungen bei.},
  subject      = {Rapid prototyping},
  language  = {de}
}
@article{StarkeAhlbehrendtBischoffetal.2009,
  author    = {Starke, G{\"u}nther and Ahlbehrendt, Norbert and Bischoff, Rainer and Melzer, Harald and Sieber, Sven and Senk, Burkhard and Kramarczyk, Peter},
  title     = {RoboTOOL. Technologien f{\"u}r den ortsflexiblen Einsatz von Robotern bei tempor{\"a}ren Arbeitsaufgaben in der Fertigung},
  series = {wt Werkstattstechnik online},
  volume    = {Bd. 99},
  journal   = {wt Werkstattstechnik online},
  number    = {H. 9},
  issn      = {1436-4980},
  pages     = {661 -- 670},
  year      = {2009},
  language  = {de}
}