@article{ItabashiKosakaMiyamotoetal.2013, author = {Itabashi, Akinori and Kosaka, Naoki and Miyamoto, Ko-ichiro and Wagner, Torsten and Sch{\"o}ning, Michael Josef}, title = {High-speed chemical imaging system based on front-side-illuminated LAPS}, series = {Sensors and actuators B: Chemical}, volume = {182}, journal = {Sensors and actuators B: Chemical}, publisher = {Elsevier}, address = {Amsterdam}, issn = {1873-3077}, doi = {10.1016/j.snb.2013.03.016}, pages = {315 -- 321}, year = {2013}, abstract = {The chemical imaging sensor is a semiconductor-based chemical sensor that can visualize the spatial distribution of specific ions on the sensing surface. The conventional chemical imaging system based on the light-addressable potentiometric sensor (LAPS), however, required a long time to obtain a chemical image, due to the slow mechanical scan of a single light beam. For high-speed imaging, a plurality of light beams modulated at different frequencies can be employed to measure the ion concentrations simultaneously at different locations on the sensor plate by frequency division multiplex (FDM). However, the conventional measurement geometry of back-side illumination limited the bandwidth of the modulation frequency required for FDM measurement, because of the low-pass filtering characteristics of carrier diffusion in the Si substrate. In this study, a high-speed chemical imaging system based on front-side-illuminated LAPS was developed, which achieved high-speed spatiotemporal recording of pH change at a rate of 70 frames per second.}, language = {en} } @inproceedings{Engels2013, author = {Engels, Elmar}, title = {A field bus library for MATLAB based on open core engineering}, series = {Proceedings to the 14th International Workshop on Research and Education in Mechatronics, REM 2013, Wien, 05.06.-06.06.2013.}, booktitle = {Proceedings to the 14th International Workshop on Research and Education in Mechatronics, REM 2013, Wien, 05.06.-06.06.2013.}, isbn = {978-3-90275-907-8}, year = {2013}, language = {en} } @book{Mueller2013, author = {M{\"u}ller, Thomas}, title = {K{\"o}rperschaftsteuergesetz / Unter Mitarb. von ... Thomas M{\"u}ller ...}, editor = {M{\"o}ssner, Manfred}, publisher = {NWB Verl.}, address = {Herne}, isbn = {978-3-482-64311-8}, pages = {XXIV, 2048 S.}, year = {2013}, language = {de} } @article{LindenFischoederLaacketal.2013, author = {Linden, A. and Fisch{\"o}der, M. and Laack, Walter van and Staat, Manfred}, title = {Einschr{\"a}nkung von Taluskippung und -vorschub durch Sprunggelenkorthesen nach fibularer Bandruptur}, series = {OUP Zeitschrift f{\"u}r die orthop{\"a}dische und unfallchirurgische Praxis}, volume = {2}, journal = {OUP Zeitschrift f{\"u}r die orthop{\"a}dische und unfallchirurgische Praxis}, number = {6}, publisher = {Deutscher {\"A}rzte-Verl.}, address = {K{\"o}ln}, isbn = {2193-5785}, doi = {10.3238/oup.2013.0306-0309}, pages = {306 -- 309}, year = {2013}, abstract = {Die fibulare Bandruptur z{\"a}hlt zu einer der am h{\"a}ufigsten auftretenden Verletzungen des Bewegungsapparats. In den meisten F{\"a}llen wird heute die konservativ fr{\"u}hfunktionelle Therapie mit Sprunggelenkorthesen allgemein bevorzugt. Im Rahmen der vorliegenden Studie wurden 14 verschiedene Sprunggelenkorthesen im Hinblick auf ihre Einschr{\"a}nkung von Taluskippung und Talusvorschub untersucht. Zur Simulation einer fibularen Bandruptur wurde ein Unterschenkelmodell aus Holz mit Fußteil, mit angelegten Orthesen in einen Scheuba-Halteapparat eingespannt und mit 150 N seitlich sowie anterior-posterior belastet. Anhand der erstellten "gehaltenen" R{\"o}ntgenaufnahmen konnten Taluskippung und Talusvorschub jeder einzelnen Orthese eindeutig bestimmt werden. Die meisten Orthesen erreichten zufriedenstellende Ergebnisse. Es stellte sich heraus, dass vor allem eine eng anliegende, im Gelenkbereich anatomisch angepasste Form vorteilhaft zu sein scheint.}, language = {de} } @article{Mueller2013, author = {M{\"u}ller, Thomas}, title = {Aufweichung der Gewaltenteilung und Demokratieverlust - Achtung vor dem Parlament. Darstellung einer Rechtsch{\"o}pfung der Exekutive im Umfeld des \S15 AStG}, series = {Der Betrieb}, journal = {Der Betrieb}, number = {11}, publisher = {Fachmedien Otto Schmidt}, address = {D{\"u}sseldorf}, issn = {0005-9935}, pages = {542 -- 548}, year = {2013}, language = {de} } @incollection{WolfFraentz2013, author = {Wolf, Martin and Fr{\"a}ntz, Birgit}, title = {Erfolgreiches IT-Marketing}, series = {Erfolgreiches IT-Marketing in Zeiten von Social Media, Cloud \& Co. - (CIO-Handbuch ; 2)}, booktitle = {Erfolgreiches IT-Marketing in Zeiten von Social Media, Cloud \& Co. - (CIO-Handbuch ; 2)}, edition = {1. Auflage}, publisher = {Symposion Publishing}, address = {D{\"u}sseldorf}, isbn = {978-3-86329-612-4}, pages = {123 -- 140}, year = {2013}, language = {de} } @article{SchneiderSchneider2013, author = {Schneider, Bettina and Schneider, Wilhelm}, title = {Rechnungslegung nach IFRS im Vergleich zum HGB}, series = {Das Wirtschaftsstudium : wisu ; Zeitschrift f{\"u}r Ausbildung, Examen, Berufseinstieg und Fortbildung}, journal = {Das Wirtschaftsstudium : wisu ; Zeitschrift f{\"u}r Ausbildung, Examen, Berufseinstieg und Fortbildung}, publisher = {Lange}, address = {D{\"u}sseldorf}, issn = {0340-3084}, pages = {536 -- 541}, year = {2013}, language = {de} } @inproceedings{Engels2013, author = {Engels, Elmar}, title = {Industrieantriebe mit sercos Schnittstelle {\"u}ber MATLAB steuern}, series = {Tagungsband AALE 2013 : das Forum f{\"u}r Fachleute der Automatisierungstechnik aus Hochschulen und Wirtschaft ; 10. Fachkonferenz, Stralsund}, booktitle = {Tagungsband AALE 2013 : das Forum f{\"u}r Fachleute der Automatisierungstechnik aus Hochschulen und Wirtschaft ; 10. Fachkonferenz, Stralsund}, publisher = {DIV Dt. Industrieverl.}, address = {M{\"u}nchen}, isbn = {978-3-8356-3364-3}, pages = {223 -- 232}, year = {2013}, language = {de} } @book{Weissmantel2013, author = {Weißmantel, Ralf}, title = {Plakatzeichen : Plakate mit Schrift {\"u}ber Schrift ; 50 typografische Plakate ; Kommunikationsdesign}, publisher = {Fachhochschule Aachen, Fachbereich Design}, address = {Aachen}, isbn = {978-3-00041325-4}, pages = {51 S. : {\"u}berw. Ill.}, year = {2013}, language = {de} } @article{Frings2013, author = {Frings, Michael}, title = {Begrenzung von vertraglichen H{\"o}chstfristen f{\"u}r Zahlungen und Abnahmen}, series = {Neue Wirtschaftsbriefe NWB Steuer- und Wirtschaftsrecht}, journal = {Neue Wirtschaftsbriefe NWB Steuer- und Wirtschaftsrecht}, publisher = {NWB Verlag}, address = {Herne}, issn = {0028-3460}, pages = {49 -- 56}, year = {2013}, language = {de} } @article{Frings2013, author = {Frings, Michael}, title = {{\"A}nderungen zur Haftung und Verg{\"u}tung im Vereins- und Stiftungsrecht}, series = {Neue Wirtschaftsbriefe NWB Steuer- und Wirtschaftsrecht}, journal = {Neue Wirtschaftsbriefe NWB Steuer- und Wirtschaftsrecht}, publisher = {NWB Verlag}, address = {Herne}, issn = {0028-3460}, pages = {693 -- 699}, year = {2013}, language = {de} } @article{Gaiser2013, author = {Gaiser, Lorenz}, title = {Rapidshare Kinocharts}, series = {Idiopendent Lyfestile (Boxhorn ; 27)}, journal = {Idiopendent Lyfestile (Boxhorn ; 27)}, editor = {Mohr, Klaus}, publisher = {FH}, address = {Aachen}, issn = {1864-2535}, pages = {150 -- 153}, year = {2013}, language = {de} } @article{Fabo2013, author = {Fabo, Sabine}, title = {Pepr{\"a}sentatives D{\"o}sen}, series = {Idiopendent Lyfestile (Boxhorn ; 27)}, journal = {Idiopendent Lyfestile (Boxhorn ; 27)}, editor = {Mohr, Klaus}, publisher = {FH}, address = {Aachen}, issn = {1864-2535}, pages = {134 -- 139}, year = {2013}, language = {de} } @article{Mohr2013, author = {Mohr, Klaus}, title = {DEBEDE DE HAKAPE}, series = {Idiopendent Lyfestile (Boxhorn ; 27)}, journal = {Idiopendent Lyfestile (Boxhorn ; 27)}, publisher = {Fachhochschule Aachen}, address = {Aachen}, issn = {1864-2535}, pages = {40 -- 45}, year = {2013}, language = {de} } @article{FeuchtSchoenbachLanzletal.2013, author = {Feucht, Nikolaus and Sch{\"o}nbach, Etienne Michael and Lanzl, Ines and Kotliar, Konstantin and Lohmann, Chris Patrick and Maier, Mathias}, title = {Changes in the foveal microstructure after intravitreal bevacizumab application in patients with retinal vascular disease}, series = {Clinical Ophthalmology}, volume = {7}, journal = {Clinical Ophthalmology}, publisher = {Dove Medical Press}, address = {Auckland, New Zealand}, issn = {1177-5483}, pages = {173 -- 178}, year = {2013}, language = {en} } @article{MurganBeyerKotliaretal.2013, author = {Murgan, Ilina and Beyer, Sonja and Kotliar, Konstantin and Weber, Lutz and Bechtold-Dalla Pozza, Susanne and Dalla Pozza, Robert and Wegner, Aharon and Sitnikova, Diana and Stock, Konrad and Heemann, Uwe and Schmaderer, Christoph and Baumann, M.}, title = {Arterial and Retinal Vascular Changes in Hypertensive and Prehypertensive Adolescents}, series = {American Journal of Hypertension}, volume = {26}, journal = {American Journal of Hypertension}, number = {3}, publisher = {Oxford University Press}, address = {Oxford}, issn = {1941-7225}, pages = {400 -- 408}, year = {2013}, language = {de} } @article{KotliarHanssenEberhardtetal.2013, author = {Kotliar, Konstantin and Hanssen, Henner and Eberhardt, Karla and Vilser, Walthard and Schmaderer, Christoph and Halle, Martin and Heemann, Uwe and Baumann, M.}, title = {Retinal pulse wave velocity in young male normotensive and mildly hypertensive subjects}, series = {Microcirculation}, journal = {Microcirculation}, publisher = {Wiley}, address = {Malden}, issn = {1549-8719}, year = {2013}, language = {en} } @article{ReisertSchneiderGeissleretal.2013, author = {Reisert, Steffen and Schneider, Benno and Geissler, Hanno and Gompel, Matthias van and Wagner, Patrick and Sch{\"o}ning, Michael Josef}, title = {Multi-sensor chip for the investigation of different types of metal oxides for the detection of H2O2 in the ppm range}, series = {physica status solidi (a)}, volume = {210}, journal = {physica status solidi (a)}, number = {5}, publisher = {Wiley}, address = {Weinheim}, issn = {1862-6319}, pages = {898 -- 904}, year = {2013}, abstract = {In this work, a multi-sensor chip for the investigation of the sensing properties of different types of metal oxides towards hydrogen peroxide in the ppm range is presented. The fabrication process and physical characterization of the multi-sensor chip are described. Pure SnO2 and WO3 as well as Pd- and Pt-doped SnO2 films are characterized in terms of their sensitivity to H2O2. The sensing films have been prepared by drop-coating of water-dispensed nano-powders. A physical characterization, including scanning electron microscopy and X-ray diffraction analysis of the deposited metal-oxide films, was done. From the measurements in hydrogen peroxide atmosphere, it could be shown, that all of the tested metal oxide films are suitable for the detection of H2O2 in the ppm range. The highest sensitivity and reproducibility was achieved using Pt-doped SnO2. Calibration plot of a SnO2, WO3, Pt-, and Pd-doped SnO2 gas sensor for H2O2 concentrations in the ppm range.}, language = {en} } @article{HennemannKohlReisertetal.2013, author = {Hennemann, J{\"o}rg and Kohl, Claus-Dieter and Reisert, Steffen and Kirchner, Patrick and Sch{\"o}ning, Michael Josef}, title = {Copper oxide nanofibres for detection of hydrogen peroxide vapour at high concentrations}, series = {physica status solidi (a)}, volume = {210}, journal = {physica status solidi (a)}, number = {5}, publisher = {Wiley}, address = {Weinheim}, issn = {1862-6319}, doi = {10.1002/pssa.201200775}, pages = {859 -- 863}, year = {2013}, abstract = {We present a sensor concept based on copper(II)oxide (CuO) nanofibres for the detection of hydrogen peroxide (H2O2) vapour in the percent per volume (\% v/v) range. The fibres were produced by using the electrospinning technique. To avoid water condensation in the pores, the fibres were initially modified by an exposure to H2S to get an enclosed surface. By a thermal treatment at 350 °C the fibres were oxidised back to CuO. Thereby, the visible pores disappear which was verified by SEM analysis. The fibres show a decrease of resistance with increasing H2O2 concentration which is due to the fact that hydrogen peroxide is an oxidising gas and CuO a p-type semiconductor. The sensor shows a change of resistance within the minute range to the exposure until the maximum concentration of 6.9\% v/v H2O2. At operating temperatures below 450 °C the corresponding sensor response to a concentration of 4.1\% v/v increases. The sensor shows a good reproducibility of the signal at different measurements. CuO seems to be a suitable candidate for the detection of H2O2 vapour at high concentrations. Resistance behaviour of the sensor under exposure to H2O2 vapours between 2.3 and 6.9\% v/v at an operating temperature of 450 °C.}, language = {en} } @incollection{RoethKampkerReisgenetal.2013, author = {R{\"o}th, Thilo and Kampker, Achim and Reisgen, Uwe and Hameyer, Kay and De Doncker, R. W.}, title = {Entwicklung von elektrofahrzeugspezifischen Systemen}, series = {Elektromobilit{\"a}t : Grundlagen einer Zukunftstechnologie}, booktitle = {Elektromobilit{\"a}t : Grundlagen einer Zukunftstechnologie}, publisher = {Springer}, address = {Berlin}, isbn = {978-3-642-31986-0}, pages = {235 -- 336}, year = {2013}, abstract = {Die Fahrzeugkarosserie bildet als gr{\"o}ßte funktionale und organisatorische Systemeinheit ein zentrales Kompetenzfeld der OEMs. F{\"u}r den Fahrzeughersteller stellt der Karosserierohbau eine hohe Kernkompetenz sowohl in der Produktentwicklung als auch in der Produktion dar. Neue, innovative Karosseriebauweisen, bspw. aufgrund eines neuen Fahrzeugkonzeptes oder neuer Anforderungen, bedeuten f{\"u}r den OEM auch gleichzeitig die intensive Auseinandersetzung mit Kompetenzfokussierung bzw. Wertsch{\"o}pfungsverlagerungen.}, language = {de} }