@article{MichelButenwegKinkel2018, author = {Michel, Philipp and Butenweg, Christoph and Kinkel, Sven}, title = {Pile-grid foundations of onshore wind turbines considering soil-structure-interaction under seismic loading}, series = {Soil Dynamics and Earthquake Engineering}, volume = {109}, journal = {Soil Dynamics and Earthquake Engineering}, publisher = {Elsevier}, address = {Amsterdam}, issn = {0267-7261}, doi = {10.1016/j.soildyn.2018.03.009}, pages = {299 -- 311}, year = {2018}, abstract = {In recent years, many onshore wind turbines are erected in seismic active regions and on soils with poor load bearing capacity, where pile grids are inevitable to transfer the loads into the ground. In this contribution, a realistic multi pile grid is designed to analyze the dynamics of a wind turbine tower including frequency dependent soil-structure-interaction. It turns out that different foundations on varying soil configurations heavily influence the vibration response. While the vibration amplitude is mostly attenuated, certain unfavorable combinations of structure and soil parameters lead to amplification in the range of the system's natural frequencies. This testifies the need for overall dynamic analysis in the assessment of the dynamic stability and the holistic frequency tuning of the turbines.}, language = {en} } @article{MikulicsAdamKordosetal.2005, author = {Mikulics, M. and Adam, R. and Kordos, P. and F{\"o}rster, Arnold and L{\"u}th, H. and Wu, S. and Zheng, X. and Sobolewski, R.}, title = {Ultrafast low-temperature-grown epitaxial GaAs photodetectors transferred on flexible plastic substrates}, series = {IEEE photonics technology letters : IEEE PTL. 17 (2005), H. 8}, journal = {IEEE photonics technology letters : IEEE PTL. 17 (2005), H. 8}, isbn = {1041-1135}, pages = {1725 -- 1727}, year = {2005}, language = {en} } @article{MikulicsCamaraHardtetal.2004, author = {Mikulics, M. and Camara, I. and Hardt, A. van der and Fox, A. and F{\"o}rster, Arnold and Gusten, R. and L{\"u}th, H. and Kordos, P.}, title = {Generation of THz radiation by photomixing in low-temperature-grown MBE GaAs}, series = {Fifth International Conference on Advanced Semiconductor Devices and Microsystems : conference proceedings ; Smolenice Castle, Slovakia, October 17 - 21, 2004 / [organizers: Institute of Electrical Engineering, Slovak Academy of Sciences, Bratislava and Microelectronics Department, Faculty of Electrical Engineering and Information Technology, Slovak University of Technology, Bratislava]. Ed. by J. Osvald}, journal = {Fifth International Conference on Advanced Semiconductor Devices and Microsystems : conference proceedings ; Smolenice Castle, Slovakia, October 17 - 21, 2004 / [organizers: Institute of Electrical Engineering, Slovak Academy of Sciences, Bratislava and Microelectronics Department, Faculty of Electrical Engineering and Information Technology, Slovak University of Technology, Bratislava]. Ed. by J. Osvald}, publisher = {IEEE Operations Center}, address = {Piscataway, NJ}, isbn = {0-7803-8335-7}, pages = {231 -- 234}, year = {2004}, language = {en} } @article{MikulicsMarsoCamaraMayorgaetal.2005, author = {Mikulics, M. and Marso, M. and C{\´a}mara Mayorga, I. and Gusten, R. and Stancek, S. and Michael, E. A. and Schieder, R. and Wolter, M. and Buca, D. and F{\"o}rster, Arnold and Kordos, P. and L{\"u}th, H.}, title = {Photomixers fabricated on nitrogen-ion-implanted GaAs}, series = {Applied physics letters. 87 (2005)}, journal = {Applied physics letters. 87 (2005)}, pages = {041106-1 -- 041106-3}, year = {2005}, language = {en} } @article{MistlerAnthoineButenweg2007, author = {Mistler, Michael and Anthoine, A. and Butenweg, Christoph}, title = {In-plane and out-of-plane homogenisation of masonry}, series = {Computers \& structures}, volume = {Volume 85}, journal = {Computers \& structures}, number = {Issues 17-18}, issn = {1879-2243 (E-Journal); 0045-7949 (Print)}, doi = {10.1016/j.compstruc.2006.08.087}, pages = {1321 -- 1330}, year = {2007}, language = {en} } @article{MistlerButenweg2005, author = {Mistler, Michael and Butenweg, Christoph}, title = {Verformungsbasierter seismischer Nachweis von Mauerwerksbauten mit der Kapazit{\"a}tsspektrum-Methode}, series = {Mauerwerk : European journal of masonry}, volume = {Volume 9}, journal = {Mauerwerk : European journal of masonry}, number = {Issue 6}, issn = {1437-1022 (E-Journal); 1432-3427 (Print)}, doi = {10.1002/dama.200590098}, pages = {255 -- 261}, year = {2005}, language = {de} } @article{MistlerButenwegFehlingetal.2007, author = {Mistler, Michael and Butenweg, Christoph and Fehling, Ekkehard and St{\"u}rz, Jochen}, title = {Verformungsbasierte seismische Bemessung von Mauerwerksbauten auf Grundlage zyklischer Schubwandversuche}, series = {Bauingenieur : die richtungsweisende Zeitschrift im Bauingenieurswesen ; offizielle Zeitschrift der VDI-Gesellschaft Bautechnik. Beilage: D-A-CH-Mitteilungsblatt}, volume = {Band 82}, journal = {Bauingenieur : die richtungsweisende Zeitschrift im Bauingenieurswesen ; offizielle Zeitschrift der VDI-Gesellschaft Bautechnik. Beilage: D-A-CH-Mitteilungsblatt}, issn = {1434-6591}, pages = {S3 -- S11}, year = {2007}, language = {de} } @article{MistlerButenwegMeskouris2006, author = {Mistler, Michael and Butenweg, Christoph and Meskouris, Konstantin}, title = {Modelling methods of historic masonry buildings under seismic excitation}, series = {Journal of seismology}, volume = {Volume 10}, journal = {Journal of seismology}, number = {No. 4}, issn = {1383-4649 (Print) ; 1573-157X (E-Journal)}, doi = {10.1007/s10950-006-9033-z}, pages = {497 -- 510}, year = {2006}, language = {en} } @article{Mohnke1987, author = {Mohnke, Andreas}, title = {High-rate sputtering of zinc oxide with a funnel-shaped magnetic field: Effect of the target thickness on the layer properties}, series = {Vakuum-Technik. 36 (1987), H. 5}, journal = {Vakuum-Technik. 36 (1987), H. 5}, isbn = {0042-2266}, pages = {148 -- 151}, year = {1987}, language = {en} } @article{Mohnke1985, author = {Mohnke, Andreas}, title = {Kathodenzerst{\"a}ubung von Zinkoxid f{\"u}r die Akustoelektronik}, series = {Universit{\"a}t : Wissenschaftliche Beitr{\"a}ge : WB (1985)}, journal = {Universit{\"a}t : Wissenschaftliche Beitr{\"a}ge : WB (1985)}, isbn = {0440-1298}, pages = {94 -- 95}, year = {1985}, language = {de} } @article{MohnkeSchuckel1986, author = {Mohnke, Andreas and Schuckel, G.}, title = {Tempern von Oberfl{\"a}chenwellenwandlern in Schichtstruktur}, series = {Technische Hochschule Ilmenau / Bibliothek: Wissenschaftliche Zeitschrift. 32 (1986), H. 3}, journal = {Technische Hochschule Ilmenau / Bibliothek: Wissenschaftliche Zeitschrift. 32 (1986), H. 3}, isbn = {0043-6917}, pages = {151 -- 160}, year = {1986}, language = {de} } @article{MohnkeSchuckel1985, author = {Mohnke, Andreas and Schuckel, G.}, title = {Eigenschaften des Schichtsystems ZnO/Glas f{\"u}r die Mikroakustik. Schuckel, G.; Mohnke, A.}, series = {Technische Hochschule Ilmenau / Bibliothek: Wissenschaftliche Zeitschrift. 31 (1985), H. 4}, journal = {Technische Hochschule Ilmenau / Bibliothek: Wissenschaftliche Zeitschrift. 31 (1985), H. 4}, isbn = {0043-6917}, pages = {157 -- 164}, year = {1985}, language = {de} } @article{MorandiButenwegBreisetal.2022, author = {Morandi, Paolo and Butenweg, Christoph and Breis, Khaled and Beyer, Katrin and Magenes, Guido}, title = {Latest findings on the behaviour factor q for the seismic design of URM buildings}, series = {Bulletin of Earthquake Engineering}, volume = {20}, journal = {Bulletin of Earthquake Engineering}, number = {11}, editor = {Ansal, Atilla}, publisher = {Springer Nature}, address = {Cham}, issn = {1573-1456}, doi = {10.1007/s10518-022-01419-7}, pages = {5797 -- 5848}, year = {2022}, abstract = {Recent earthquakes as the 2012 Emilia earthquake sequence showed that recently built unreinforced masonry (URM) buildings behaved much better than expected and sustained, despite the maximum PGA values ranged between 0.20-0.30 g, either minor damage or structural damage that is deemed repairable. Especially low-rise residential and commercial masonry buildings with a code-conforming seismic design and detailing behaved in general very well without substantial damages. The low damage grades of modern masonry buildings that was observed during this earthquake series highlighted again that codified design procedures based on linear analysis can be rather conservative. Although advances in simulation tools make nonlinear calculation methods more readily accessible to designers, linear analyses will still be the standard design method for years to come. The present paper aims to improve the linear seismic design method by providing a proper definition of the q-factor of URM buildings. These q-factors are derived for low-rise URM buildings with rigid diaphragms which represent recent construction practise in low to moderate seismic areas of Italy and Germany. The behaviour factor components for deformation and energy dissipation capacity and for overstrength due to the redistribution of forces are derived by means of pushover analyses. Furthermore, considerations on the behaviour factor component due to other sources of overstrength in masonry buildings are presented. As a result of the investigations, rationally based values of the behaviour factor q to be used in linear analyses in the range of 2.0-3.0 are proposed.}, language = {en} } @article{MottaghyPechnig2009, author = {Mottaghy, Darius and Pechnig, Renate}, title = {Numerische 3D Modelle zur Temperaturvorhersage und Reservoirsimulationen}, series = {BBR - Fachmagazin f{\"u}r Brunnen- und Leitungsbau}, volume = {60}, journal = {BBR - Fachmagazin f{\"u}r Brunnen- und Leitungsbau}, number = {10}, pages = {44 -- 51}, year = {2009}, language = {de} } @article{MottaghyPechnigTaugsetal.2010, author = {Mottaghy, Darius and Pechnig, Renate and Taugs, Renate and Kr{\"o}ger, Jens and Thomsen, Claudia and Hesse, Fabian and Liebsch-Doerschner, Thomas}, title = {Erstellung eines geothermischen Modells f{\"u}r Teile Hamburgs und anliegende Gebiete}, series = {BBR - Fachmagazin f{\"u}r Brunnen- und Leitungsbau}, volume = {61}, journal = {BBR - Fachmagazin f{\"u}r Brunnen- und Leitungsbau}, number = {12}, publisher = {WVGW Wirtschafts- u. Verl.Ges. Gas und Wasser}, address = {Bonn}, issn = {1611-1478}, pages = {52 -- 59}, year = {2010}, language = {de} } @article{MottaghyPechnigVogt2011, author = {Mottaghy, Darius and Pechnig, Renate and Vogt, Christian}, title = {The geothermal project Den Haag: 3D numerical models for temperature prediction and reservoir simulation}, series = {Geothermics}, volume = {40}, journal = {Geothermics}, number = {3}, publisher = {Elsevier}, address = {Amsterdam}, issn = {0375-6505}, doi = {10.1016/j.geothermics.2011.07.001}, pages = {199 -- 210}, year = {2011}, abstract = {The proposed Den Haag Zuidwest district heating system of the city of The Hague consists of a deep doublet in a Jurassic sandstone layer that is designed for a production temperature of 75 °C and a reinjection temperature of 40 °C at a flow rate of 150 m3 h-1. The prediction of reservoir temperature and production behavior is crucial for success of the proposed geothermal doublet. This work presents the results of a study of the important geothermal and geohydrological issues for the doublet design. In the first phase of the study, the influences of the three-dimensional (3D) structures of anticlines and synclines on the temperature field were examined. A comprehensive petrophysical investigation was performed to build a large scale 3D-model of the reservoir. Several bottomhole temperatures (BHTs), as well as petrophysical logs were used to calibrate the model using thermal conductivity measurements on 50 samples from boreholes in different lithological units in the study area. Profiles and cross sections extracted from the calculated temperature field were used to study the temperature in the surrounding areas of the planned doublet. In the second phase of the project, a detailed 3D numerical reservoir model was set up, with the aim of predicting the evolution of the producer and injector temperatures, and the extent of the cooled area around the injector. The temperature model from the first phase provided the boundary conditions for the reservoir model. Hydraulic parameters for the target horizons, such as porosity and permeability, were taken from data available from the nearby exploration wells. The simulation results are encouraging as no significant thermal breakthrough is predicted. For the originally planned location of the producer, the extracted water temperature is predicted to be around 79 °C, with an almost negligible cooling in the first 50 years of production. When the producer is located shallower parts of the reservoir, the yield water temperatures is lower, starting at ≈76 °C and decreasing to ≈74 °C after 50 years of operation. This comparatively larger decrease in temperature with time is caused by the structural feature of the reservoir, namely a higher dip causes the cooler water to easily move downward. In view of the poor reservoir data, the reservoir simulation model is constructed to allow iterative updates using data assimilation during planned drilling, testing, and production phases. Measurements during an 8 h pumping test carried out in late 2010 suggest that a flow rate of 150 m3 h-1 is achievable. Fluid temperatures of 76.5 °C were measured, which is very close to the predicted value.}, language = {en} } @article{MottaghyRath2006, author = {Mottaghy, Darius and Rath, Volker}, title = {Latent heat effects in subsurface heat transport modelling and their impact on palaeotemperature reconstructions}, series = {Geophysical Journal International}, volume = {164}, journal = {Geophysical Journal International}, number = {1}, issn = {1365-246X}, doi = {10.1111/j.1365-246X.2005.02843.x}, pages = {236 -- 245}, year = {2006}, language = {en} } @article{MottaghySchellschmidtPopovetal.2005, author = {Mottaghy, Darius and Schellschmidt, R. and Popov, Y. A. and Clauser, C. and Kukkonen, I. T. and Nover, G. and Milanovsky, S. and Romushkevich, R. A.}, title = {New heat flow data from the immediate vicinity of the Kola super-deep borehole: Vertical variation in heat flow density confirmed and attributed to advection}, series = {Tectonophysics}, volume = {401}, journal = {Tectonophysics}, number = {1-2}, issn = {1879-3266}, doi = {10.1016/j.tecto.2005.03.005}, pages = {119 -- 142}, year = {2005}, language = {en} } @article{MottaghySchwambornRath2013, author = {Mottaghy, Darius and Schwamborn, G. and Rath, V.}, title = {Past climate changes and permafrost depth at the Lake El'gygytgyn site: implications from data and thermal modeling}, series = {Climate of the Past}, volume = {9}, journal = {Climate of the Past}, number = {1}, publisher = {Copernicus}, address = {Katlenburg-Lindau}, issn = {1814-9332}, doi = {10.5194/cp-9-119-2013}, pages = {119 -- 133}, year = {2013}, language = {en} } @article{MottaghyVosteenSchellschmidt2008, author = {Mottaghy, Darius and Vosteen, Hans-Dieter and Schellschmidt, R{\"u}diger}, title = {Temperature dependence of the relationship of thermal diffusivity versus thermal conductivity for crystalline rocks}, series = {International Journal of Earth Sciences}, volume = {97}, journal = {International Journal of Earth Sciences}, number = {2}, issn = {1437-3262}, doi = {10.1007/s00531-007-0238-3}, pages = {435 -- 442}, year = {2008}, language = {en} }