@article{MiyamotoSugawaraKanohetal.2010,
  author    = {Miyamoto, Ko-ichiro and Sugawara, Yuri and Kanoh, Shin´ichiro and Yoshinobu, Tatsuo and Wagner, Torsten and Sch{\"o}ning, Michael Josef},
  title     = {Image correction method for the chemical imaging sensor},
  series = {Sensors and Actuators B: Chemical},
  volume    = {144},
  journal   = {Sensors and Actuators B: Chemical},
  number    = {2},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0925-4005},
  doi       = {10.1016/j.snb.2008.10.069},
  pages     = {344 -- 348},
  year      = {2010},
  abstract  = {The chemical imaging sensor is a semiconductor-based chemical sensor that can visualize the spatial distribution of chemical species. For the practical application of this sensor, artifacts in the chemical images due to defects of the semiconductor substrate and contamination of the sensing surface etc. have been a major problem. An image correction method was developed to eliminate the influence of nonuniformity of individual sensor plate.},
  language  = {en}
}
@article{AbouzarPoghossianSiqueiraetal.2010,
  author    = {Abouzar, Maryam H. and Poghossian, Arshak and Siqueira, Jos{\´e} R. Jr. and Oliveira, Osvaldo N. Jr. and Moritz, Werner and Sch{\"o}ning, Michael Josef},
  title     = {Capacitive electrolyte-insulator-semiconductor structures functionalised with a polyelectrolyte/enzyme multilayer: New strategy for enhanced field-effect biosensing},
  series = {Physica Status Solidi (A)},
  volume    = {207},
  journal   = {Physica Status Solidi (A)},
  number    = {4},
  publisher = {Wiley-VCH},
  address   = {Berlin},
  issn      = {1862-6300},
  doi       = {10.1002/pssa.200983317},
  pages     = {884 -- 890},
  year      = {2010},
  abstract  = {A novel strategy for enhanced field-effect biosensing using capacitive electrolyte-insulator-semiconductor (EIS) structures functionalised with pH-responsive weak polyelectrolyte/enzyme or dendrimer/enzyme multilayers is presented. The feasibility of the proposed approach is exemplarily demonstrated by realising a penicillin biosensor based on a capacitive p-Si-SiO2 EIS structure functionalised with a poly(allylamine hydrochloride) (PAH)/penicillinase and a poly(amidoamine) dendrimer/penicillinase multilayer. The developed sensors response to changes in both the local pH value near the gate surface and the charge of macromolecules induced via enzymatic reaction, resulting in a higher sensitivity. For comparison, an EIS penicillin biosensor with adsorptively immobilised penicillinase has been also studied. The highest penicillin sensitivity of 100 mV/dec has been observed for the EIS sensor functionalised with the PAH/penicillinase multilayer. The lower and upper detection limit was around 20 µM and 10 mM, respectively. In addition, an incorporation of enzymes in a multilayer prepared by layer-by-layer technique provides a larger amount of immobilised enzymes per sensor area, reduces enzyme leaching effects and thus, enhances the biosensor lifetime (the loss of penicillin sensitivity after 2 months was 10-12\%).},
  language  = {en}
}
@article{SchoeningKirchnerNgetal.2010,
  author    = {Sch{\"o}ning, Michael Josef and Kirchner, Patrick and Ng, Yue Ann and Spelthahn, Heiko and Schneider, Andreas and Henkel, Hartmut and Friedrich, Peter and Kolstad, Jens and Berger, J{\"o}rg and Keusgen, Michael},
  title     = {Gas sensor investigation based on a catalytically activated thin-film thermopile for H2O2 detection},
  series = {Physica Status Solidi (A)},
  volume    = {207},
  journal   = {Physica Status Solidi (A)},
  number    = {4},
  publisher = {Wiley-VCH},
  address   = {Berlin},
  issn      = {1862-6300},
  doi       = {10.1002/pssa.200983309},
  pages     = {787 -- 792},
  year      = {2010},
  abstract  = {In aseptic filling systems, hydrogen peroxide vapour is commonly used for the reduction of microbial contaminations in carton packages. In this process, the germicidal efficiency of the vapour depends especially on the H₂O₂ concentration. To monitor the H₂O₂ concentration, a calorimetric H₂O₂ gas sensor based on a catalytically activated thin-film thermopile is investigated. Two different sensor layouts, namely a circular and a linear form, as well as two various material pairs such as tungsten/nickel and gold/nickel, have been examined for the realization of a thin-film thermopile. Additionally, manganese oxide and palladium particles have been compared as responsive catalysts towards H₂O₂. The thin-film sensors have been investigated at various H₂O₂ concentrations, gas temperatures and flow rates.},
  language  = {en}
}
@article{BuniatyanAbouzarMartirosyanetal.2010,
  author    = {Buniatyan, Vahe V. and Abouzar, Maryam H. and Martirosyan, Norayr W. and Schubert, J{\"u}rgen and Gevorgian, Spartak and Sch{\"o}ning, Michael Josef and Poghossian, Arshak},
  title     = {pH-sensitive properties of barium strontium titanate (BST) thin films prepared by pulsed laser deposition technique},
  series = {Physica Status Solidi (A)},
  volume    = {207},
  journal   = {Physica Status Solidi (A)},
  number    = {4},
  publisher = {Wiley-VCH},
  address   = {Berlin},
  issn      = {1862-6300},
  doi       = {10.1002/pssa.200983310},
  pages     = {824 -- 830},
  year      = {2010},
  abstract  = {pH-sensitive properties of barium strontium titanate (BST) high-k thin films as alternative gate material for field-effect capacitive (bio-)chemical sensors based on an electrolyte-insulator-semiconductor system have been investigated. The BST films of different compositions (Ba0.31Sr0.69TiO3, Ba0.25Sr0.75TiO3 and Mg-doped Ba0.8Sr0.2Mg0.1Ti0.9O3) were deposited by pulsed laser deposition technique from targets fabricated by self-propagating high-temperature synthesis. The realised sensors have been electrochemically characterised by means of impedance-spectroscopy, capacitance-voltage and constant-capacitance method. The sensors possess a Nernstian-like pH sensitivity in the concentration range between pH 3 and 11 with a response time of 5-10 s. An equivalent circuit model for the BST-based capacitive field-effect sensor is discussed.},
  language  = {en}
}
@article{TurekHeidenGuoetal.2010,
  author    = {Turek, Monik and Heiden, Wolfgang and Guo, Sharon and Riesen, Alfred and Schubert, J{\"u}rgen and Zander, Willi and Kr{\"u}ger, Peter and Keusgen, Michael and Sch{\"o}ning, Michael Josef},
  title     = {Simultaneous detection of cyanide and heavy metals for environmental analysis by means of µISEs},
  series = {Physica Status Solidi (A)},
  volume    = {207},
  journal   = {Physica Status Solidi (A)},
  number    = {4},
  publisher = {Wiley-VCH},
  address   = {Berlin},
  issn      = {1862-6300},
  doi       = {10.1002/pssa.200983303},
  pages     = {817 -- 823},
  year      = {2010},
  abstract  = {In environmental analysis, cyanide and heavy metals play an important role, because these substances are highly toxic for biological systems. They can lead to chronic and acute diseases. Due to the chemical properties of cyanide it is frequently used for industrial processes such as extraction of silver and gold. Heavy metals can be found as trace elements in nature and are often applied in industries e.g., galvanization processes. Up to now, cyanide and heavy metals can be detected by several sensors separately and their detection is often limited to laboratory investigations. In this publication, with regard to an in situ analysis, a new miniaturized silicon-based sensor system for the simultaneous detection of cyanide and heavy metals in aqueous solutions is presented that is based on chalcogenide glass-based micro ion-selective electrodes (µISEs). The µISEs are incorporated into a specially designed measuring system for the simultaneous detection of heavy metals and cyanide in solutions and validated by simultaneous measurements of Cu2+- and CN--ions, Cd2+- and CN-- ions and Pb2+- and CN--ions. The particular sensor system has shown good sensor properties in the µ-molar ion-concentration range. For simultaneous measurements in complex heavy metal and cyanide solutions an intelligent software using fuzzy logic is discussed.},
  language  = {en}
}
@article{SiqueiraBaeckerPoghossianetal.2010,
  author    = {Siqueira, Jos{\´e} R. Jr. and B{\"a}cker, Matthias and Poghossian, Arshak and Zucolotto, Valtencir and Oliveira, Osvaldo N. Jr. and Sch{\"o}ning, Michael Josef},
  title     = {Associating biosensing properties with the morphological structure of multilayers containing carbon nanotubes on field-effect devices},
  series = {Physica Status Solidi (A)},
  volume    = {207},
  journal   = {Physica Status Solidi (A)},
  number    = {4},
  publisher = {Wiley-VCH},
  address   = {Berlin},
  issn      = {1862-6300},
  doi       = {10.1002/pssa.200983301},
  pages     = {781 -- 786},
  year      = {2010},
  abstract  = {The control of molecular architecture provided by the layer-by-layer (LbL) technique has led to enhanced biosensors, in which advantageous features of distinct materials can be combined. Full optimization of biosensing performance, however, is only reached if the film morphology is suitable for the principle of detection of a specific biosensor. In this paper, we report a detailed morphology analysis of LbL films made with alternating layers of single-walled carbon nanotubes (SWNTs) and polyamidoamine (PAMAM) dendrimers, which were then covered with a layer of penicillinase (PEN). An optimized performance to detect penicillin G was obtained with 6-bilayer SWNT/PAMAM LbL films deposited on p-Si-SiO2-Ta2O5 chips, used in biosensors based on a capacitive electrolyte-insulator-semiconductor (EIS) and a light-addressable potentiometric sensor (LAPS) structure, respectively. Field-emission scanning electron microscopy (FESEM) and atomic force microscopy (AFM) images indicated that the LbL films were porous, with a large surface area due to interconnection of SWNT into PAMAM layers. This morphology was instrumental for the adsorption of a larger quantity of PEN, with the resulting LbL film being highly stable. The experiments to detect penicillin were performed with constant-capacitance (ConCap) and constant-current (CC) measurements for EIS and LAPS sensors, respectively, which revealed an enhanced detection signal and sensitivity of ca. 100 mV/decade for the field-effect sensors modified with the PAMAM/SWNT LbL film. It is concluded that controlling film morphology is essential for an enhanced performance of biosensors, not only in terms of sensitivity but also stability and response time.},
  language  = {en}
}
@article{GosslaButtelWahrmundetal.2010,
  author    = {Gossla, Ulrich and Buttel, Luc and Wahrmund, Holger and Mehlig, Bernd},
  title     = {Bemessung, Anwendung und Qualit{\"a}tssicherung von Stahlfaserspritzbeton im Tunnelbau},
  series = {Beton- und Stahlbetonbau},
  volume    = {105},
  journal   = {Beton- und Stahlbetonbau},
  number    = {2},
  publisher = {Ernst \& Sohn},
  address   = {Berlin},
  issn      = {0005-9900},
  doi       = {10.1002/best.200900688},
  pages     = {92 -- 101},
  year      = {2010},
  abstract  = {Die Spritzbetonbauweise hat sich im Tunnelbau seit Jahren bew{\"a}hrt. Spritzbeton wird als unbewehrter Beton, in Verbindung mit Bewehrung sowie als Stahlfaserspritzbeton eingesetzt. Bei den meisten Tunnelschalen aus Stahlfaserspritzbeton werden Stahlfasern derzeit nur als konstruktive Bewehrung verwendet. Die Faserzugabe f{\"u}hrt zu einer nennenswerten Erh{\"o}hung der Bruchenergie und somit zu einer h{\"o}heren Z{\"a}higkeit des sonst spr{\"o}den Materials und damit zu einer h{\"o}heren Sicherheit. Stahlfaserspritzbeton kann auch anstelle von Spritzbeton mit statisch erforderlicher Mattenbewehrung eingesetzt werden. Die Bemessung erfolgt dann unter Ber{\"u}cksichtigung der Nachrisszugfestigkeit. Diese kann wie bei Stahlfaserbeton an Biegebalken ermittelt werden, die aus gr{\"o}ßeren Proben herausges{\"a}gt werden. Anhand von verschiedenen Beispielen werden die unterschiedlichen Anwendungen aufgezeigt und die daf{\"u}r erforderlichen Pr{\"u}fungen vorgestellt.},
  language  = {de}
}
@article{UllrichGrottkeRossaintetal.2010,
  author    = {Ullrich, Sebastian and Grottke, Oliver and Rossaint, Rolf and Staat, Manfred and Deserno, Thomas M. and Kuhlen, Torsten},
  title     = {Virtual Needle Simulation with Haptics for Regional Anaesthesia},
  pages     = {3 Seiten},
  year      = {2010},
  language  = {en}
}
@article{Timme2010,
  author    = {Timme, Michael},
  title     = {Mietschuldenfreiheitsbescheinigung durch den bisherigen Vermieter?},
  series = {MDR Monatsschrift f{\"u}r Deutsches Recht},
  volume    = {64},
  journal   = {MDR Monatsschrift f{\"u}r Deutsches Recht},
  number    = {2},
  publisher = {Verlag Dr. Otto Schmidt},
  address   = {K{\"o}ln},
  issn      = {0340-1812},
  doi       = {10.9785/ovs-mdtr-2010-60},
  pages     = {60 -- 61},
  year      = {2010},
  abstract  = {Der VIII. Zivilsenat des BGH hat entschieden, dass ein Mieter von seinem ehemaligen Vermieter keine „Mietschuldenfreiheitsbescheinigung'' verlangen kann, die {\"u}ber eine Quittung f{\"u}r die erhaltenen Mietzahlungen hinausgeht. Der folgende Beitrag untersucht die Konsequenzen der aktuellen Entscheidung.},
  language  = {de}
}
@article{TimmeHuelk2010,
  author    = {Timme, Michael and H{\"u}lk, Fabian},
  title     = {Schriftform bei Mietvertrag mit einer Aktiengesellschaft},
  series = {Neue Zeitschrift f{\"u}r Gesellschaftsrecht (NZG)},
  volume    = {13},
  journal   = {Neue Zeitschrift f{\"u}r Gesellschaftsrecht (NZG)},
  number    = {5},
  publisher = {Beck},
  address   = {M{\"u}nchen},
  issn      = {1434-9272},
  pages     = {177 -- 178},
  year      = {2010},
  language  = {de}
}
@article{Timme2010,
  author    = {Timme, Michael},
  title     = {Die Schenkung eines Tieres an einen beschr{\"a}nkt Gesch{\"a}ftsf{\"a}higen},
  series = {Juristische Arbeitsbl{\"a}tter},
  journal   = {Juristische Arbeitsbl{\"a}tter},
  publisher = {Beck},
  address   = {M{\"u}nchen},
  issn      = {0720-6356},
  pages     = {174 -- 176},
  year      = {2010},
  language  = {de}
}
@article{SiqueiraMakiPaulovichetal.2010,
  author    = {Siqueira, Jose R. and Maki, Rafael M. and Paulovich, Fernando V. and Werner, Frederik and Poghossian, Arshak and Oliveira, Maria C. F. de and Zucolotto, Valtencir and Oliveira, Osvaldo N. Jr. and Sch{\"o}ning, Michael Josef},
  title     = {Use of information visualization methods eliminating cross talk in multiple sensing units investigated for a light-addressable potentiometric sensor},
  series = {Analytical Chemistry},
  volume    = {82},
  journal   = {Analytical Chemistry},
  number    = {1},
  publisher = {ACS Publications},
  address   = {Washington},
  issn      = {0003-2700},
  doi       = {10.1021/ac9024076},
  pages     = {61 -- 65},
  year      = {2010},
  abstract  = {The integration of nanostructured films containing biomolecules and silicon-based technologies is a promising direction for reaching miniaturized biosensors that exhibit high sensitivity and selectivity. A challenge, however, is to avoid cross talk among sensing units in an array with multiple sensors located on a small area. In this letter, we describe an array of 16 sensing units of a light-addressable potentiometric sensor (LAPS), which was made with layer-by-layer (LbL) films of a poly(amidomine) dendrimer (PAMAM) and single-walled carbon nanotubes (SWNTs), coated with a layer of the enzyme penicillinase. A visual inspection of the data from constant-current measurements with liquid samples containing distinct concentrations of penicillin, glucose, or a buffer indicated a possible cross talk between units that contained penicillinase and those that did not. With the use of multidimensional data projection techniques, normally employed in information visualization methods, we managed to distinguish the results from the modified LAPS, even in cases where the units were adjacent to each other. Furthermore, the plots generated with the interactive document map (IDMAP) projection technique enabled the distinction of the different concentrations of penicillin, from 5 mmol L-1 down to 0.5 mmol L-1. Data visualization also confirmed the enhanced performance of the sensing units containing carbon nanotubes, consistent with the analysis of results for LAPS sensors. The use of visual analytics, as with projection methods, may be essential to handle a large amount of data generated in multiple sensor arrays to achieve high performance in miniaturized systems},
  language  = {en}
}
@article{GrottkeBraunschweigPhilippenetal.2010,
  author    = {Grottke, O. and Braunschweig, T. and Philippen, B. and Gatzweiler, Karl-Heinz and Gronloh, N. and Staat, Manfred and Rossaint, R. and Tolba, R.},
  title     = {A new model for blunt liver injuries in the swine},
  series = {European Surgical Research},
  volume    = {44},
  journal   = {European Surgical Research},
  number    = {2},
  publisher = {Karger},
  address   = {Basel},
  issn      = {1421-9921},
  doi       = {10.1159/000265053},
  pages     = {65 -- 73},
  year      = {2010},
  abstract  = {Background: To elaborate the impact of new haemostatic agents we developed an instrument for the pressure-controlled induction of blunt liver injuries in a porcine animal model. Materials and Methods: A dilutional coagulopathy of 80\% of animal blood volume was induced in 9 anaesthetized pigs. Animals were randomly assigned to be injured with a force of 112 Newton (N) (n = 1), 224 ± 19 N (n = 4) or 355 ± 35 N (n = 4). The impact of injury was measured by blood loss, survival time and coagulation parameters. Liver histology was obtained to evaluate the degree of liver injury. Results: The profound haemodilution resulted in a significant alteration of all coagulation parameters. After inflicting the injury with 355 ± 35 N, both the survival time (30 ± 9 min; p = 0.006) and blood loss (68 ± 16 ml min-1, p = 0.002) were significantly different as compared to injuries with 224 ± 19 N (survival time: 76 ± 20 min, blood loss: 23 ± 4 ml min-1). In contrast, an injury with 112 N led to an insignificant blood loss of only 239 ml. Conclusion: We developed a pressure-controlled clamp that allows for the induction of blunt liver traumas with highly reproducible injuries with a positive correlation with blood loss and survival.},
  language  = {en}
}
@article{Hirschberg2010,
  author    = {Hirschberg, Rainer},
  title     = {Energetische Bewertung raumlufttechnischer Anlagen. Vereinfachtes Verfahren nach DIN V 18599},
  series = {Deutsche K{\"a}lte-Klima-Tagung 2010 Magdeburg},
  journal   = {Deutsche K{\"a}lte-Klima-Tagung 2010 Magdeburg},
  publisher = {DKV},
  address   = {Hannover},
  isbn      = {978-3-932715-46-4},
  pages     = {26 Seiten},
  year      = {2010},
  abstract  = {Unter Energieeffizienz wird verstanden, dass ein definiertes Ziel mit m{\"o}glichst wenig Energie erreicht wird. Im Beitrag wird zun{\"a}chst eine Formel zur Berechnung der Gesamtenergieeffizienz eines Geb{\"a}udes angegeben. Darauf aufbauend wird ein 3-S{\"a}ulen-Modell zur Energieeinsparung vorgeschlagen. Es beinhaltet vereinfachte Verfahren zur Berechnung der Betriebseigenschaften von Heizanlagen, raumlufttechnischen Anlagen und K{\"u}hl- und Kaltwasseranlagen. Am Beispiel einer RLT-Anlage wird die Vorgehensweise der Bewertung n{\"a}her erl{\"a}utert. Zusammenfassend wird festgestellt, dass das vereinfachte Verfahren eine schnelle und sichere energetische Bewertung der genannten Anlagen erlaubt,, zu Pr{\"a}senzwissen f{\"u}hrt, die Haupteinflussgr{\"o}ßen aufzeigt und eine Anlagenbewertung ohne Geb{\"a}udebewertung gew{\"a}hrleistet. Das vereinfachte Verfahren wird im Fr{\"u}hjahr 2011 verf{\"u}gbar sein. Es soll Bestandteil der DIN V 18599 werden, und die EnEV 2012 soll darauf Bezug nehmen.},
  language  = {de}
}
@article{ZhubanovaAknazarovMansurovetal.2010,
  author    = {Zhubanova, Azhar A. and Aknazarov, S. K. and Mansurov, Zulkhair and Digel, Ilya and Kozhalakova, A. A. and Akimbekov, Nuraly S. and O'Heras, Carlos and Tazhibayeva, S. and Artmann, Gerhard and Temiz Artmann, Ayseg{\"u}l},
  title     = {Adsorption of bacterial Lipopolysaccharides and blood plasma proteins on modified carbonized materials},
  year      = {2010},
  abstract  = {Bacterial lipopolysaccharides (endotoxins) show strong biological effects at very low concentrations in human beings and many animals when entering the blood stream. These include affecting structure and function of organs and cells, changing metabolic functions, raising body temperature, triggering the coagulation cascade, modifying hemodynamics and causing septic shock. Because of this toxicity, the removal of even minute amounts is essential for safe parenteral administration of drugs and also for septic shock patients' care. The absence of a general method for endotoxin removal from liquid interfaces urgently requires finding new methods and materials to overcome this gap. Nanostructured carbonized plant parts is a promising material that showed good adsorption properties due to its vast pore network and high surface area. The aim of this study was comparative measurement of endotoxin- and blood proteins-related adsorption rate and adsorption capacity for different carboneous materials produced at different temperatures and under different surface modifications. As a main surface modificator, positively cbarged polymer, polyethileneimine (PEl) was used. Activated carbon materials showed good adsorption properties for LPS and some proteins used in the experiments. During the batch experiments, several techniques (dust removal, autoclaving) were used and optimized for improving the material's adsorption behavior. Also, with the results obtained it was possible to differentiate the materials according to their adsorption capacity and kinetic characteristics. Modification of the surface apparently has not affected hemoglobin binding to the adsorbent's surface. Obtained adsorption isotherms can be used as a powerful tool for designing of future column-based setups for blood purification from LPS, which is especially important for septic shock treatment.},
  subject      = {Kohlenstofffaser},
  language  = {en}
}