@article{AchtsnichtNeuendorfFassbenderetal.2019, author = {Achtsnicht, Stefan and Neuendorf, Christian and Faßbender, Tobias and N{\"o}lke, Greta and Offenh{\"a}usser, Andreas and Krause, Hans-Joachim and Schr{\"o}per, Florian}, title = {Sensitive and rapid detection of cholera toxin subunit B using magnetic frequency mixing detection}, series = {Plos One}, volume = {14}, journal = {Plos One}, number = {7}, publisher = {Plos}, address = {San Francisco}, issn = {1932-6203}, doi = {10.1371/journal.pone.0219356}, pages = {e0219356}, year = {2019}, abstract = {Cholera is a life-threatening disease caused by the cholera toxin (CT) as produced by some Vibrio cholerae serogroups. In this research we present a method which directly detects the toxin's B subunit (CTB) in drinking water. For this purpose we performed a magnetic sandwich immunoassay inside a 3D immunofiltration column. We used two different commercially available antibodies to capture CTB and for binding to superparamagnetic beads. ELISA experiments were performed to select the antibody combination. The beads act as labels for the magnetic frequency mixing detection technique. We show that the limit of detection depends on the type of magnetic beads. A nonlinear Hill curve was fitted to the calibration measurements by means of a custom-written python software. We achieved a sensitive and rapid detection of CTB within a broad concentration range from 0.2 ng/ml to more than 700 ng/ml.}, language = {en} } @inproceedings{MarinkovićButenweg2019, author = {Marinković, Marko and Butenweg, Christoph}, title = {Experimental and numerical analysis of RC frames with decoupled masonry infills}, series = {7th ECCOMAS Thematic Conference on Computational Methods in Structural Dynamics and Earthquake Engineering}, booktitle = {7th ECCOMAS Thematic Conference on Computational Methods in Structural Dynamics and Earthquake Engineering}, editor = {Papadrakakis, Manolis and Fragiadakis, Michalis}, publisher = {National Technical University of Athens}, address = {Athen}, isbn = {978-618-82844-5-6}, issn = {2623-3347}, doi = {10.7712/120119.7088.18845}, pages = {2464 -- 2479}, year = {2019}, abstract = {Masonry infill walls are commonly used in reinforced concrete (RC) frame structures, also in seismically active areas, although they often experience serious damage during earthquakes. One of the main reasons for their poor behaviour is the connection to the frame, which is usually constructed using mortar. This paper describes the novel solution for infill/frame connection based on application of elastomeric material between them. The system called INODIS (Innovative Decoupled Infill System) has the aim to postpone the activation of infill in in-plane direction and at the same time to provide sufficient out-of-plane support. First, experimental tests on infilled frame specimens are presented and the comparison of the results between traditionally infilled frames and infilled frames with the INODIS system are given. The results are then used for calibration and validation of numerical model, which can be further employed for investigating the influence of some material parameters on the behaviour of infilled frames with the INODIS system.}, language = {en} } @article{Gaigall2019, author = {Gaigall, Daniel}, title = {On a new approach to the multi-sample goodness-of-fit problem}, series = {Communications in Statistics - Simulation and Computation}, volume = {53}, journal = {Communications in Statistics - Simulation and Computation}, number = {10}, publisher = {Taylor \& Francis}, address = {London}, issn = {1532-4141}, doi = {10.1080/03610918.2019.1618472}, pages = {2971 -- 2989}, year = {2019}, abstract = {Suppose we have k samples X₁,₁,…,X₁,ₙ₁,…,Xₖ,₁,…,Xₖ,ₙₖ with different sample sizes ₙ₁,…,ₙₖ and unknown underlying distribution functions F₁,…,Fₖ as observations plus k families of distribution functions {G₁(⋅,ϑ);ϑ∈Θ},…,{Gₖ(⋅,ϑ);ϑ∈Θ}, each indexed by elements ϑ from the same parameter set Θ, we consider the new goodness-of-fit problem whether or not (F₁,…,Fₖ) belongs to the parametric family {(G₁(⋅,ϑ),…,Gₖ(⋅,ϑ));ϑ∈Θ}. New test statistics are presented and a parametric bootstrap procedure for the approximation of the unknown null distributions is discussed. Under regularity assumptions, it is proved that the approximation works asymptotically, and the limiting distributions of the test statistics in the null hypothesis case are determined. Simulation studies investigate the quality of the new approach for small and moderate sample sizes. Applications to real-data sets illustrate how the idea can be used for verifying model assumptions.}, language = {en} } @article{BaringhausGaigall2019, author = {Baringhaus, Ludwig and Gaigall, Daniel}, title = {On an asymptotic relative efficiency concept based on expected volumes of confidence regions}, series = {Statistics - A Journal of Theoretical and Applied Statistic}, volume = {53}, journal = {Statistics - A Journal of Theoretical and Applied Statistic}, number = {6}, publisher = {Taylor \& Francis}, address = {London}, issn = {1029-4910}, doi = {10.1080/02331888.2019.1683560}, pages = {1396 -- 1436}, year = {2019}, abstract = {The paper deals with an asymptotic relative efficiency concept for confidence regions of multidimensional parameters that is based on the expected volumes of the confidence regions. Under standard conditions the asymptotic relative efficiencies of confidence regions are seen to be certain powers of the ratio of the limits of the expected volumes. These limits are explicitly derived for confidence regions associated with certain plugin estimators, likelihood ratio tests and Wald tests. Under regularity conditions, the asymptotic relative efficiency of each of these procedures with respect to each one of its competitors is equal to 1. The results are applied to multivariate normal distributions and multinomial distributions in a fairly general setting.}, language = {en} } @incollection{SchmitzDietzeCzarnecki2019, author = {Schmitz, Manfred and Dietze, Christian and Czarnecki, Christian}, title = {Enabling digital transformation through robotic process automation at Deutsche Telekom}, series = {Enabling digital transformation through robotic process automation at Deutsche Telekom}, booktitle = {Enabling digital transformation through robotic process automation at Deutsche Telekom}, editor = {Urbach, Nils and R{\"o}glinger, Maximilian}, publisher = {Springer}, address = {Cham}, isbn = {978-3-319-95272-7}, doi = {10.1007/978-3-319-95273-4_2}, pages = {15 -- 33}, year = {2019}, abstract = {Due to the high number of customer contacts, fault clearances, installations, and product provisioning per year, the automation level of operational processes has a significant impact on financial results, quality, and customer experience. Therefore, the telecommunications operator Deutsche Telekom (DT) has defined a digital strategy with the objectives of zero complexity and zero complaint, one touch, agility in service, and disruptive thinking. In this context, Robotic Process Automation (RPA) was identified as an enabling technology to formulate and realize DT's digital strategy through automation of rule-based, routine, and predictable tasks in combination with structured and stable data.}, language = {en} } @incollection{BensbergBuscherCzarnecki2019, author = {Bensberg, Frank and Buscher, Gandalf and Czarnecki, Christian}, title = {Digital transformation and IT topics in the consulting industry: a labor market perspective}, series = {Advances in consulting research : recent findings and practical cases}, booktitle = {Advances in consulting research : recent findings and practical cases}, editor = {Nissen, Volker}, publisher = {Springer}, address = {Cham}, isbn = {978-3-319-95998-6}, doi = {10.1007/978-3-319-95999-3_16}, pages = {341 -- 357}, year = {2019}, abstract = {Information technologies, such as big data analytics, cloud computing, cyber physical systems, robotic process automation, and the internet of things, provide a sustainable impetus for the structural development of business sectors as well as the digitalization of markets, enterprises, and processes. Within the consulting industry, the proliferation of these technologies opened up the new segment of digital transformation, which focuses on setting up, controlling, and implementing projects for enterprises from a broad range of sectors. These recent developments raise the question, which requirements evolve for IT consultants as important success factors of those digital transformation projects. Therefore, this empirical contribution provides indications regarding the qualifications and competences necessary for IT consultants in the era of digital transformation from a labor market perspective. On the one hand, this knowledge base is interesting for the academic education of consultants, since it supports a market-oriented design of adequate training measures. On the other hand, insights into the competence requirements for consultants are considered relevant for skill and talent management processes in consulting practice. Assuming that consulting companies pursue a strategic human resource management approach, labor market information may also be useful to discover strategic behavioral patterns.}, language = {en} } @inproceedings{BrockmannSultanowCzarnecki2019, author = {Brockmann, Carsten and Sultanow, Eldar and Czarnecki, Christian}, title = {Is enterprise architecture still relevant in the digital age?}, series = {GI Edition Proceedings Band 295 INFORMATIK 2019, Workshop-Beitr{\"a}ge}, booktitle = {GI Edition Proceedings Band 295 INFORMATIK 2019, Workshop-Beitr{\"a}ge}, editor = {Draude, Claude and Lange, Martin and Sick, Bernhard}, publisher = {K{\"o}llen}, address = {Bonn}, isbn = {9783885796893}, issn = {1617-5468}, doi = {10.18420/inf2019_ws01}, pages = {21 -- 21}, year = {2019}, language = {en} } @inproceedings{AuthCzarneckiBensberg2019, author = {Auth, Gunnar and Czarnecki, Christian and Bensberg, Frank}, title = {Impact of robotic process automation on enterprise architectures}, series = {GI Edition Proceedings Band 295 INFORMATIK 2019, Workshop-Beitr{\"a}ge}, booktitle = {GI Edition Proceedings Band 295 INFORMATIK 2019, Workshop-Beitr{\"a}ge}, editor = {Draude, Claude and Lange, Martin and Sick, Bernhard and Gesellschaft f{\"u}r Informatik e.V. (GI),}, publisher = {K{\"o}llen}, address = {Bonn}, isbn = {9783885796893}, issn = {1617-5468}, doi = {10.18420/inf2019_ws05}, pages = {59 -- 65}, year = {2019}, abstract = {The initial idea of Robotic Process Automation (RPA) is the automation of business processes through the presentation layer of existing application systems. For this simple emulation of user input and output by software robots, no changes of the systems and architecture is required. However, considering strategic aspects of aligning business and technology on an enterprise level as well as the growing capabilities of RPA driven by artificial intelligence, interrelations between RPA and Enterprise Architecture (EA) become visible and pose new questions. In this paper we discuss the relationship between RPA and EA in terms of perspectives and implications. As workin- progress we focus on identifying new questions and research opportunities related to RPA and EA.}, language = {en} } @inproceedings{SteuerDankertLeichtScholten2019, author = {Steuer-Dankert, Linda and Leicht-Scholten, Carmen}, title = {Diversity- and innovation management in complex engineering organizations}, series = {7th International OFEL Conference on Governance, Management and Entrepreneurship: Embracing Diversity in Organisations. April 5th - 6th, 2019, Dubrovnik, Croatia}, booktitle = {7th International OFEL Conference on Governance, Management and Entrepreneurship: Embracing Diversity in Organisations. April 5th - 6th, 2019, Dubrovnik, Croatia}, editor = {Tipurić, Darko and Hruška, Domagoj}, publisher = {Governance Research and Development Centre (CIRU)}, address = {Zagreb}, pages = {136 -- 157}, year = {2019}, abstract = {Diversity is increasingly being addressed as an innovation-promoting factor. For this reason, companies and institutions tackle the integration of a diversity management approach that enables a heterogenic perspective on innovation development. However, system-theoretical frameworks state that the implementation of diversity measures that are not tailored to the needs of the organization often leads to a rejection or reactivity with regard to the management approach. In this context, especially organizations, which are characterized by a specific hierarchical structure, a dominant habitus or specialist culture, must face the challenge of realizing a sustainable change of the corporate culture that sets the basis for implementing diversity management approaches. The presented research project focuses on analyzing the situation in a huge scientific collaborative project - so called Cluster of Excellence (CoE) - with the aim to implement a diversity - and innovation management strategy. Considering the influencing determinants, the CoE is characterized by its embeddedness in the scientific system, a complex organizational structure, and a high fluctuation rate. The paper presents a systemic approach of reflecting these factors in order to develop a diversity- and innovation management strategy. In this frame, the results of a quantitative survey of CoE employees and derived mindset-types are presented. The results show a need for taking different mindset-types into account, to be able to develop a tailored management strategy. The aim of the project is to give recommendations for developing a sustainable management concept that promotes both diversity and innovation by drawing on the persisting mindsets of organization members while reflecting top down as well as bottom up factors of implementation processes as well as the psychology of change. This paper addresses all who are concerned with the management of human resources in innovation processes and are striving for a cultural change within the framework of complex organizations.}, language = {en} } @article{SteuerDankertGilmartinMulleretal.2019, author = {Steuer-Dankert, Linda and Gilmartin, Shannon K. and Muller, Carol B. and Dungs, Carolin and Sheppard, Sheri and Leicht-Scholten, Carmen}, title = {Expanding engineering limits : a concept for socially responsible education of engineers}, series = {The international journal of engineering education}, volume = {35}, journal = {The international journal of engineering education}, number = {2}, isbn = {0949-149X}, pages = {658 -- 673}, year = {2019}, language = {en} } @article{Kurz2019, author = {Kurz, Melanie}, title = {Images of Sweden in Germany: from Sundborn and Bullerby to Ikea}, series = {nomad: the magazine for new design culture, business affairs and contemporary lifestyle}, journal = {nomad: the magazine for new design culture, business affairs and contemporary lifestyle}, number = {8}, isbn = {2513-0714}, pages = {136 -- 147}, year = {2019}, language = {en} } @inproceedings{GrundmannBauerBodenetal.2019, author = {Grundmann, Jan Thimo and Bauer, Waldemar and Boden, Ralf Christian and Ceriotti, Matteo and Cordero, Federico and Dachwald, Bernd and Dumont, Etienne and Grimm, Christian D. and Hercik, D. and Herique, A. and Ho, Tra-Mi and Jahnke, Rico and Kofman, Wlodek and Lange, Caroline and Lichtenheldt, Roy and McInnes, Colin R. and Mikschl, Tobias and Mikulz, Eugen and Montenegro, Sergio and Moore, Iain and Pelivan, Ivanka and Peloni, Alessandro and Plettemeier, Dirk and Quantius, Dominik and Reershemius, Siebo and Renger, Thomas and Riemann, Johannes and Rogez, Yves and Ruffer, Michael and Sasaki, Kaname and Schmitz, Nicole and Seboldt, Wolfgang and Seefeldt, Patric and Spietz, Peter and Spr{\"o}witz, Tom and Sznajder, Maciej and Toth, Norbert and Viavattene, Giulia and Wejmo, Elisabet and Wolff, Friederike and Ziach, Christian}, title = {Responsive integrated small spacecraft solar sail and payload design concepts and missions}, series = {Conference: 5th International Symposium on Solar Sailing (ISSS 2019)}, booktitle = {Conference: 5th International Symposium on Solar Sailing (ISSS 2019)}, year = {2019}, abstract = {Asteroid mining has the potential to greatly reduce the cost of in-space manufacturing, production of propellant for space transportation and consumables for crewed spacecraft, compared to launching the required resources from Earth's deep gravity well. This paper discusses the top-level mission architecture and trajectory design for these resource-return missions, comparing high-thrust trajectories with continuous low-thrust solar-sail trajectories. This work focuses on maximizing the economic Net Present Value, which takes the time-cost of finance into account and therefore balances the returned resource mass and mission duration. The different propulsion methods will then be compared in terms of maximum economic return, sets of attainable target asteroids, and mission flexibility. This paper provides one more step towards making commercial asteroid mining an economically viable reality by integrating trajectory design, propulsion technology and economic modelling.}, language = {en} } @inproceedings{GrundmannBauerBodenetal.2019, author = {Grundmann, Jan Thimo and Bauer, Waldemar and Boden, Ralf Christian and Ceriotti, Matteo and Cordero, Federico and Dachwald, Bernd and Dumont, Etienne and Grimm, Christian D. and Hercik, D. and Herique, A. and Ho, Tra-Mi and Jahnke, Rico and Kofman, Wlodek and Lange, Caroline and Lichtenheldt, Roy and McInnes, Colin R. and Mikschl, Tobias and Montenegro, Sergio and Moore, Iain and Pelivan, Ivanka and Peloni, Alessandro and Plettenmeier, Dirk and Quantius, Dominik and Reershemius, Siebo and Renger, Thomas and Riemann, Johannes and Rogez, Yves and Ruffer, Michael and Sasaki, Kaname and Schmitz, Nicole and Seboldt, Wolfgang and Seefeldt, Patric and Spietz, Peter and Spr{\"o}witz, Tom and Sznajder, Maciej and Toth, Norbert and Viavattene, Giulia and Wejmo, Elisabet and Wolff, Friederike and Ziach, Christian}, title = {Responsive exploration and asteroid characterization through integrated solar sail and lander development using small spacecraft technologies}, series = {IAA Planetary Defense Conference}, booktitle = {IAA Planetary Defense Conference}, year = {2019}, abstract = {In parallel to the evolution of the Planetary Defense Conference, the exploration of small solar system bodies has advanced from fast fly-bys on the sidelines of missions to the planets to the implementation of dedicated sample-return and in-situ analysis missions. Spacecraft of all sizes have landed, touch-and-go sampled, been gently beached, or impacted at hypervelocity on asteroid and comet surfaces. More have flown by close enough to image their surfaces in detail or sample their immediate environment, often as part of an extended or re-purposed mission. And finally, full-scale planetary defense experiment missions are in the making. Highly efficient low-thrust propulsion is increasingly applied beyond commercial use also in mainstream and flagship science missions, in combination with gravity assist propulsion. Another development in the same years is the growth of small spacecraft solutions, not in size but in numbers and individual capabilities. The on-going NASA OSIRIS-REx and JAXA HAYABUSA2 missions exemplify the trend as well as the upcoming NEA SCOUT mission or the landers MINERVA-II and MASCOT recently deployed on Ryugu. We outline likely as well as possible and efficient routes of continuation of all these developments towards a propellant-less and highly efficient class of spacecraft for small solar system body exploration: small spacecraft solar sails designed for carefree handling and equipped with carried landers and application modules, for all asteroid user communities -planetary science, planetary defence, and in-situ resource utilization. This projection builds on the experience gained in the development of deployable membrane structures leading up to the successful ground deployment test of a (20 m)² solar sail at DLR Cologne and in the 20 years since. It draws on the background of extensive trajectory optimization studies, the qualified technology of the DLR GOSSAMER-1 deployment demonstrator, and the MASCOT asteroid lander. These enable 'now-term' as well as near-term hardware solutions, and thus responsive fast-paced development. Mission types directly applicable to planetary defense include: single and Multiple NEA Rendezvous ((M)NR) for mitigation precursor, target monitoring and deflection follow-up tasks; sail-propelled head-on retrograde kinetic impactors (RKI) for mitigation; and deployable membrane based methods to modify the asteroid's properties or interact with it. The DLR-ESTEC GOSSAMER Roadmap initiated studies of missions uniquely feasible with solar sails such as Displaced L1 (DL1) space weather advance warning and monitoring and Solar Polar Orbiter (SPO) delivery which demonstrate the capability of near-term solar sails to achieve NEA rendezvous in any kind of orbit, from Earth-coorbital to extremely inclined and even retrograde orbits. For those mission types using separable payloads, such as SPO, (M)NR and RKI, design concepts can be derived from the separable Boom Sail Deployment Units characteristic of DLR GOSSAMER solar sail technology, nanolanders like MASCOT, or microlanders like the JAXA-DLR Jupiter Trojan Asteroid Lander for the OKEANOS mission which can shuttle from the sail to the asteroids visited and enable multiple NEA sample-return missions. These are an ideal match for solar sails in micro-spacecraft format whose launch configurations are compatible with ESPA and ASAP secondary payload platforms.}, language = {en} } @inproceedings{MuellerAltherrAholaetal.2019, author = {M{\"u}ller, Tim M. and Altherr, Lena and Ahola, Marja and Schabel, Samuel and Pelz, Peter F.}, title = {Multi-Criteria optimization of pressure screen systems in paper recycling - balancing quality, yield, energy consumption and system complexity}, series = {EngOpt 2018 Proceedings of the 6th International Conference on Engineering Optimization}, booktitle = {EngOpt 2018 Proceedings of the 6th International Conference on Engineering Optimization}, editor = {Rodrigues, H. C.}, publisher = {Springer International Publishing}, address = {Basel}, isbn = {978-3-319-97773-7}, doi = {10.1007/978-3-319-97773-7_105}, year = {2019}, abstract = {The paper industry is the industry with the third highest energy consumption in the European Union. Using recycled paper instead of fresh fibers for papermaking is less energy consuming and saves resources. However, adhesive contaminants in recycled paper are particularly problematic since they reduce the quality of the resulting paper-product. To remove as many contaminants and at the same time obtain as many valuable fibres as possible, fine screening systems, consisting of multiple interconnected pressure screens, are used. Choosing the best configuration is a non-trivial task: The screens can be interconnected in several ways, and suitable screen designs as well as operational parameters have to be selected. Additionally, one has to face conflicting objectives. In this paper, we present an approach for the multi-criteria optimization of pressure screen systems based on Mixed-Integer Nonlinear Programming. We specifically focus on a clear representation of the trade-off between different objectives.}, language = {en} } @inproceedings{LorenzAltherrPelz2019, author = {Lorenz, Imke-Sophie B. and Altherr, Lena and Pelz, Peter F.}, title = {Graph-theoretic resilience analysis of a water distribution system's topology}, series = {World Congress on Resilience, Reliability and Asset Management 2019}, booktitle = {World Congress on Resilience, Reliability and Asset Management 2019}, pages = {106 -- 109}, year = {2019}, abstract = {Water suppliers are faced with the great challenge of achieving high-quality and, at the same time, low-cost water supply. In practice, the focus is set on the most beneficial maintenance measures and/or capacity adaptations of existing water distribution systems (WDS). Since climatic and demographic influences will pose further challenges in the future, the resilience enhancement of WDS, i.e. the enhancement of their capability to withstand and recover from disturbances, has been in particular focus recently. To assess the resilience of WDS, metrics based on graph theory have been proposed. In this study, a promising approach is applied to assess the resilience of the WDS for a district in a major German City. The conducted analysis provides insight into the process of actively influencing the resilience of WDS}, language = {en} } @incollection{StengerAltherrAbel2019, author = {Stenger, David and Altherr, Lena and Abel, Dirk}, title = {Machine learning and metaheuristics for black-box optimization of product families: a case-study investigating solution quality vs. computational overhead}, series = {Operations Research Proceedings 2018}, booktitle = {Operations Research Proceedings 2018}, publisher = {Springer}, address = {Cham}, isbn = {978-3-030-18499-5 (Print)}, doi = {10.1007/978-3-030-18500-8_47}, pages = {379 -- 385}, year = {2019}, abstract = {In product development, numerous design decisions have to be made. Multi-domain virtual prototyping provides a variety of tools to assess technical feasibility of design options, however often requires substantial computational effort for just a single evaluation. A special challenge is therefore the optimal design of product families, which consist of a group of products derived from a common platform. Finding an optimal platform configuration (stating what is shared and what is individually designed for each product) and an optimal design of all products simultaneously leads to a mixed-integer nonlinear black-box optimization model. We present an optimization approach based on metamodels and a metaheuristic. To increase computational efficiency and solution quality, we compare different types of Gaussian process regression metamodels adapted from the domain of machine learning, and combine them with a genetic algorithm. We illustrate our approach on the example of a product family of electrical drives, and investigate the trade-off between solution quality and computational overhead.}, language = {en} } @incollection{LeiseAltherrSimonetal.2019, author = {Leise, Philipp and Altherr, Lena and Simon, Nicolai and Pelz, Peter F.}, title = {Finding global-optimal gearbox designs for battery electric vehicles}, series = {Optimization of complex systems - theory, models, algorithms and applications : WCGO 2019}, booktitle = {Optimization of complex systems - theory, models, algorithms and applications : WCGO 2019}, publisher = {Springer}, address = {Cham}, isbn = {978-3-030-21802-7}, doi = {10.1007/978-3-030-21803-4_91}, pages = {916 -- 925}, year = {2019}, abstract = {In order to maximize the possible travel distance of battery electric vehicles with one battery charge, it is mandatory to adjust all components of the powertrain carefully to each other. While current vehicle designs mostly simplify the powertrain rigorously and use an electric motor in combination with a gearbox with only one fixed transmission ratio, the use of multi-gear systems has great potential. First, a multi-speed system is able to improve the overall energy efficiency. Secondly, it is able to reduce the maximum momentum and therefore to reduce the maximum current provided by the traction battery, which results in a longer battery lifetime. In this paper, we present a systematic way to generate multi-gear gearbox designs that—combined with a certain electric motor—lead to the most efficient fulfillment of predefined load scenarios and are at the same time robust to uncertainties in the load. Therefore, we model the electric motor and the gearbox within a Mixed-Integer Nonlinear Program, and optimize the efficiency of the mechanical parts of the powertrain. By combining this mathematical optimization program with an unsupervised machine learning algorithm, we are able to derive global-optimal gearbox designs for practically relevant momentum and speed requirements.}, language = {en} } @inproceedings{GrundmannBauerBodenetal.2019, author = {Grundmann, Jan Thimo and Bauer, Waldemar and Boden, Ralf and Ceriotti, Matteo and Chand, Suditi and Cordero, Federico and Dachwald, Bernd and Dumont, Etienne and Grimm, Christian D. and Heiligers, Jeannette and Herč{\´i}k, David and H{\´e}rique, Alain and Ho, Tra-Mi and Jahnke, Rico and Kofman, Wlodek and Lange, Caroline and Lichtenheldt, Roy and McInnes, Colin and Meß, Jan-Gerd and Mikschl, Tobias and Mikulz, Eugen and Montenegro, Sergio and Moore, Iain and Pelivan, Ivanka and Peloni, Alessandro and Plettemeier, Dirk and Quantius, Dominik and Reershemius, Siebo and Renger, Thomas and Riemann, Johannes and Rogez, Yves and Ruffer, Michael and Sasaki, Kaname and Schmitz, Nicole and Seboldt, Wolfgang and Seefeldt, Patric and Spietz, Peter and Spr{\"o}witz, Tom and Sznajder, Maciej and T{\´o}th, Norbert and Vergaaij, Merel and Viavattene, Giulia and Wejmo, Elisabet and Wiedemann, Carsten and Wolff, Friederike and Ziach, Christian}, title = {Flights are ten a sail - Re-use and commonality in the design and system engineering of small spacecraft solar sail missions with modular hardware for responsive and adaptive exploration}, series = {70th International Astronautical Congress (IAC)}, booktitle = {70th International Astronautical Congress (IAC)}, isbn = {9781713814856}, pages = {1 -- 7}, year = {2019}, language = {en} } @inproceedings{BergmannGraebenerWildetal.2019, author = {Bergmann, Kevin and Gr{\"a}bener, Josefine and Wild, Dominik and Ulfers, H. and Czupalla, Markus}, title = {Study on thermal stabilization of a GEO-stationary telescope baffling system by integral application of phase change material}, series = {International Conference on Environmental Systems}, booktitle = {International Conference on Environmental Systems}, pages = {1 -- 14}, year = {2019}, abstract = {The utilization of phase change material (PCM) for latent heat storage and thermal control of spacecraft has been demonstrated in the past in few missions only. One limiting factor was the fact that all concepts developed so far envisioned the PCM to be applied as an additional capacitor, encapsulated in its own housing, leading to mass, efficiency and accommodation challenges. Recently, the application of PCM within the scan cavity of a GEOS type satellite has been suggested, in order to tackle thermal issues due to direct sun intrusion (Choi, M., 2014). However, the application of PCM in such complex mechanical structures is extremely challenging. A new concept to tackle this issue is currently under development at the FH Aachen University of Applied Sciences. The concept "Infused Thermal Solutions (ITS)" is based on the idea to 3D print metallic structures in their regular functional shape, but double walled with internal lattice support structures, allowing the infusion of a PCM layer directly into the voids and eliminating the need for additional parts and interfaces. Together with OHB System, FH Aachen theoretically studied the application of this technology to the Meteosat Third Generation (MTG) Infra-Red Sounder (IRS) instrument. The study focuses on the scan cavity and entrance baffling assembly (EBA) of the IRS. It consists of thermal analyses, 3D-redesign and bread boarding of a scaled and PCM infused EBA version. In the thermal design of the alternative EBA, PCM was applied directly into the EBA, simulating the worst hot case sun intrusion of the mission. By applying 4kg of PCM (to a 60kg baffle) the EBA temperature excursions during sun intrusion were limited from 140K to 30K, leading to a significant thermo-opto-elastic performance gain. This paper introduces the ITS concept development status.}, language = {en} } @phdthesis{Beckmann2019, author = {Beckmann, Nils}, title = {Characterization of the hydrogen-dry-low-Nox-micromix-combustion-principle for hydrogen-methane fuel mixtures}, publisher = {RMIT University}, address = {Melbourne}, pages = {XV, 160 Seiten}, year = {2019}, language = {en} }