@article{OrzadaLaddBitz2016,
  author    = {Orzada, Stephan and Ladd, Mark E. and Bitz, Andreas},
  title     = {A method to approximate maximum local SAR in multichannel transmit MR systems without transmit phase information},
  series = {Magnetic Resonance in Medicine},
  volume    = {78},
  journal   = {Magnetic Resonance in Medicine},
  number    = {2},
  publisher = {International Society for Magnetic Resonance in Medicine},
  issn      = {1522-2594},
  doi       = {10.1002/mrm.26398},
  pages     = {805 -- 811},
  year      = {2016},
  abstract  = {Purpose To calculate local specific absorption rate (SAR) correctly, both the amplitude and phase of the signal in each transmit channel have to be known. In this work, we propose a method to derive a conservative upper bound for the local SAR, with a reasonable safety margin without knowledge of the transmit phases of the channels. Methods The proposed method uses virtual observation points (VOPs). Correction factors are calculated for each set of VOPs that prevent underestimation of local SAR when the VOPs are applied with the correct amplitudes but fixed phases. Results The proposed method proved to be superior to the worst-case calculation based on the maximum eigenvalue of the VOPs. The mean overestimation for six coil setups could be reduced, whereas no underestimation of the maximum local SAR occurred. In the best investigated case, the overestimation could be reduced from a factor of 3.3 to a factor of 1.7. Conclusion The upper bound for the local SAR calculated with the proposed method allows a fast estimation of the local SAR based on power measurements in the transmit channels and facilitates SAR monitoring in systems that do not have the capability to monitor transmit phases},
  language  = {en}
}
@article{FiedlerLaddBitz2017,
  author    = {Fiedler, Thomas M. and Ladd, Mark E. and Bitz, Andreas},
  title     = {RF safety assessment of a bilateral four-channel transmit/receive 7 Tesla breast coil: SAR versus temperature limits},
  series = {Medical Physics},
  volume    = {44},
  journal   = {Medical Physics},
  number    = {1},
  doi       = {10.1002/mp.12034},
  pages     = {143 -- 157},
  year      = {2017},
  language  = {en}
}
@article{NoureddineKraffLaddetal.2017,
  author    = {Noureddine, Yacine and Kraff, Oliver and Ladd, Mark E. and Wrede, Karsten H. and Chen, Bixia and Quick, Harald H. and Schaefers, Gregor and Bitz, Andreas},
  title     = {In vitro and in silico assessment of RF-induced heating around intracranial aneurysm clips at 7 Tesla},
  series = {Magnetic Resonance in Medicine},
  journal   = {Magnetic Resonance in Medicine},
  number    = {Early view},
  publisher = {Wiley},
  address   = {Weinheim},
  issn      = {1522-2594},
  doi       = {10.1002/mrm.26650},
  pages     = {14 Seiten},
  year      = {2017},
  language  = {en}
}
@article{FiedlerLaddBitz2017,
  author    = {Fiedler, Thomas M. and Ladd, Mark E. and Bitz, Andreas},
  title     = {SAR Simulations \& Safety},
  series = {NeuroImage},
  journal   = {NeuroImage},
  number    = {Epub ahead of print},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1053-8119},
  doi       = {10.1016/j.neuroimage.2017.03.035},
  year      = {2017},
  language  = {en}
}
@article{FerreinSteinbauer2016,
  author    = {Ferrein, Alexander and Steinbauer, Gerald},
  title     = {20 Years of RoboCup - A Subjective Retrospection},
  series = {KI - K{\"u}nstliche Intelligenz},
  volume    = {30},
  journal   = {KI - K{\"u}nstliche Intelligenz},
  number    = {3},
  publisher = {Springer},
  address   = {Berlin},
  issn      = {1610-1987},
  doi       = {10.1007/s13218-016-0449-5},
  pages     = {225 -- 232},
  year      = {2016},
  abstract  = {This summer, RoboCup competitions were held for the 20th time in Leipzig, Germany. It was the second time that RoboCup took place in Germany, 10 years after the 2006 RoboCup in Bremen. In this article, we give an overview on the latest developments of RoboCup and what happened in the different leagues over the last decade. With its 20th edition, RoboCup clearly is a success story and a role model for robotics competitions. From our personal view point, we acknowledge this by giving a retrospection about what makes RoboCup such a success.},
  language  = {en}
}
@article{FerreinSchifferBooysenetal.2016,
  author    = {Ferrein, Alexander and Schiffer, Stefan and Booysen, T. and Stopforth, R.},
  title     = {Why it is harder to run RoboCup in South Africa: Experiences from German South African collaborations},
  series = {International Journal of Advanced Robotic Systems},
  volume    = {13},
  journal   = {International Journal of Advanced Robotic Systems},
  number    = {5},
  issn      = {1729-8806},
  doi       = {10.1177/1729881416662789},
  pages     = {1 -- 13},
  year      = {2016},
  abstract  = {Robots are widely used as a vehicle to spark interest in science and technology in learners. A number of initiatives focus on this issue, for instance, the Roberta Initiative, the FIRST Lego League, the World Robot Olympiad and RoboCup Junior. Robotic competitions are valuable not only for school learners but also for university students, as the RoboCup initiative shows. Besides technical skills, the students get some project exposure and experience what it means to finish their tasks on time. But qualifying students for future high-tech areas should not only be for students from developed countries. In this article, we present our experiences with research and education in robotics within the RoboCup initiative, in Germany and South Africa; we report on our experiences with trying to get the RoboCup initiative in South Africa going. RoboCup has a huge support base of academic institutions in Germany; this is not the case in South Africa. We present our 'north-south' collaboration initiatives in RoboCup between Germany and South Africa and discuss some of the reasons why we think it is harder to run RoboCup in South Africa.},
  language  = {en}
}
@article{KoenigVoelkerWolfetal.2016,
  author    = {K{\"o}nig, Johannes Alexander and V{\"o}lker, Veronika and Wolf, Martin and Schuba, Marko},
  title     = {Gamified Hacking Offence Simulation-based Training (GHOST)},
  series = {Crisis Prevention},
  volume    = {2016},
  journal   = {Crisis Prevention},
  number    = {3},
  publisher = {Beta},
  address   = {Bonn},
  pages     = {44 -- 46},
  year      = {2016},
  language  = {de}
}
@article{HaagZontarSchleupenetal.2014,
  author    = {Haag, S. and Zontar, D. and Schleupen, Josef and M{\"u}ller, T. and Brecher, C.},
  title     = {Chain of refined perception in self-optimizing assembly of micro-optical systems},
  series = {Journal of sensors and sensor systems},
  volume    = {3},
  journal   = {Journal of sensors and sensor systems},
  number    = {1},
  publisher = {Copernicus Publ.},
  address   = {G{\"o}ttingen},
  issn      = {2194-878X},
  doi       = {10.5194/jsss-3-87-2014},
  pages     = {87 -- 95},
  year      = {2014},
  abstract  = {Today, the assembly of laser systems requires a large share of manual operations due to its complexity regarding the optimal alignment of optics. Although the feasibility of automated alignment of laser optics has been shown in research labs, the development effort for the automation of assembly does not meet economic requirements - especially for low-volume laser production. This paper presents a model-based and sensor-integrated assembly execution approach for flexible assembly cells consisting of a macro-positioner covering a large workspace and a compact micromanipulator with camera attached to the positioner. In order to make full use of available models from computer-aided design (CAD) and optical simulation, sensor systems at different levels of accuracy are used for matching perceived information with model data. This approach is named "chain of refined perception", and it allows for automated planning of complex assembly tasks along all major phases of assembly such as collision-free path planning, part feeding, and active and passive alignment. The focus of the paper is put on the in-process image-based metrology and information extraction used for identifying and calibrating local coordinate systems as well as the exploitation of that information for a part feeding process for micro-optics. Results will be presented regarding the processes of automated calibration of the robot camera as well as the local coordinate systems of part feeding area and robot base.},
  language  = {en}
}
@article{LeingartnerMaurerFerreinetal.2016,
  author    = {Leingartner, Max and Maurer, Johannes and Ferrein, Alexander and Steinbauer, Gerald},
  title     = {Evaluation of Sensors and Mapping Approaches for Disasters in Tunnels},
  series = {Journal of Field Robotics},
  volume    = {33},
  journal   = {Journal of Field Robotics},
  number    = {8},
  publisher = {Wiley-VCH},
  address   = {Weinheim},
  issn      = {1556-4967},
  doi       = {10.1002/rob.21611},
  pages     = {1037 -- 1057},
  year      = {2016},
  abstract  = {Ground or aerial robots equipped with advanced sensing technologies, such as three-dimensional laser scanners and advanced mapping algorithms, are deemed useful as a supporting technology for first responders. A great deal of excellent research in the field exists, but practical applications at real disaster sites are scarce. Many projects concentrate on equipping robots with advanced capabilities, such as autonomous exploration or object manipulation. In spite of this, realistic application areas for such robots are limited to teleoperated reconnaissance or search. In this paper, we investigate how well state-of-the-art and off-the-shelf components and algorithms are suited for reconnaissance in current disaster-relief scenarios. The basic idea is to make use of some of the most common sensors and deploy some widely used algorithms in a disaster situation, and to evaluate how well the components work for these scenarios. We acquired the sensor data from two field experiments, one from a disaster-relief operation in a motorway tunnel, and one from a mapping experiment in a partly closed down motorway tunnel. Based on these data, which we make publicly available, we evaluate state-of-the-art and off-the-shelf mapping approaches. In our analysis, we integrate opinions and replies from first responders as well as from some algorithm developers on the usefulness of the data and the limitations of the deployed approaches, respectively. We discuss the lessons we learned during the two missions. These lessons are interesting for the community working in similar areas of urban search and rescue, particularly reconnaissance and search.},
  language  = {en}
}
@article{WolfAltgen2013,
  author    = {Wolf, Martin and Altgen, Jannik},
  title     = {IT Service Management in der Region Aachen : White Paper},
  pages     = {1 -- 13},
  year      = {2013},
  language  = {de}
}
@article{SchifferFerreinLakemeyer2015,
  author    = {Schiffer, Stefan and Ferrein, Alexander and Lakemeyer, Gerhard},
  title     = {Abstracting Away Low-Level Details in Service Robotics with Fuzzy Fluents},
  series = {Model-Driven Knowledge Engineering for Improved Software Modularity in Robotics and Automation. Workshop at European Robotics Forum 2015 Vienna, Austria, March 11-13, 2015.},
  journal   = {Model-Driven Knowledge Engineering for Improved Software Modularity in Robotics and Automation. Workshop at European Robotics Forum 2015 Vienna, Austria, March 11-13, 2015.},
  pages     = {1 -- 4},
  year      = {2015},
  language  = {en}
}
@article{KlingeOttoMuehl2015,
  author    = {Klinge, Uwe and Otto, Jens and M{\"u}hl, Thomas},
  title     = {High Structural Stability of Textile Implants Prevents Pore Collapse and Preserves Effective Porosity at Strain},
  series = {BioMed Research International},
  volume    = {2015},
  journal   = {BioMed Research International},
  issn      = {2314-6133 (Print)},
  doi       = {10.1155/2015/953209},
  pages     = {7 pages},
  year      = {2015},
  language  = {en}
}
@article{FuchsRitz2011,
  author    = {Fuchs, Britta and Ritz, Thomas},
  title     = {Absatzkan{\"a}le kaum verkn{\"u}pft},
  series = {IT-Mittelstand : IT-Business im Mittelstand},
  volume    = {2011},
  journal   = {IT-Mittelstand : IT-Business im Mittelstand},
  number    = {9},
  publisher = {Medienhaus-Verlag},
  address   = {Bergisch-Gladbach},
  pages     = {16},
  year      = {2011},
  language  = {de}
}
@article{WallenbornRitz2014,
  author    = {Wallenborn, Ramona and Ritz, Thomas},
  title     = {Mobilit{\"a}t miteinander teilen : st{\"a}dtisches eCarsharing in einer vernetzten Gesellschaft ; [vernetztes Fahren von morgen]},
  series = {Neue Mobilit{\"a}t : das Magazin vom Bundesverband eMobilit{\"a}t},
  volume    = {5},
  journal   = {Neue Mobilit{\"a}t : das Magazin vom Bundesverband eMobilit{\"a}t},
  number    = {14 (Herbstausg.)},
  publisher = {Bundesverband eMobilit{\"a}t BEM},
  address   = {Berlin},
  issn      = {2191-5636},
  pages     = {92 -- 95},
  year      = {2014},
  language  = {de}
}
@article{RitzPisarczykSachtlebenetal.2014,
  author    = {Ritz, Thomas and Pisarczyk, Rafael and Sachtleben, Johanna and Leßenich, Nina},
  title     = {Usability Engineering maßgeschneidert : Modellbaukasten zur Entwicklung gebrauchstauglicher mobiler Software},
  series = {Wissenschaft trifft Praxis},
  volume    = {1},
  journal   = {Wissenschaft trifft Praxis},
  number    = {1},
  publisher = {Begleitforschung Mittelstand-Digital c/o WIK-Consult GmbH},
  address   = {Bad Honnef},
  issn      = {2198-8544 (Print)},
  pages     = {79 -- 88},
  year      = {2014},
  language  = {de}
}
@article{BragardRichter2008,
  author    = {Bragard, Michael and Richter, S. A.},
  title     = {LED-Kreisel als Praxis-Booster},
  series = {Elektor : electronics worldwide},
  volume    = {39},
  journal   = {Elektor : electronics worldwide},
  number    = {12},
  issn      = {0932-5468},
  pages     = {16},
  year      = {2008},
  language  = {de}
}
@article{BragardBragard2003,
  author    = {Bragard, Michael and Bragard, G.},
  title     = {Erweiterungen f{\"u}r das CBL2-Messinterface von Texas-Instruments},
  series = {Der mathematische und naturwissenschaftliche Unterricht : MNU ; Organ des Deutschen Vereins zur F{\"o}rderung des Mathematischen und Naturwissenschaftlichen Unterrichts e.V.},
  volume    = {56},
  journal   = {Der mathematische und naturwissenschaftliche Unterricht : MNU ; Organ des Deutschen Vereins zur F{\"o}rderung des Mathematischen und Naturwissenschaftlichen Unterrichts e.V.},
  number    = {2},
  publisher = {Seeberger},
  address   = {Neuss},
  issn      = {0025-5866},
  pages     = {87 -- 88},
  year      = {2003},
  abstract  = {Das von Texas-Instruments (TI) vertriebene Interface CBL2 wird {\"u}ber einige TI-Grafik-Rechner (TI-92, TI-89 usw.) angesteuert. Wegen seiner Handlichkeit wird dieses System beim Unterricht in wechselnden R{\"a}umen »großen« Messwerterfassungssystemen oft vorgezogen. Das CBL2 bietet drei analoge Eing{\"a}nge, die immerhin mit 10 Bit Aufl{\"o}sung und bis zu einer Frequenz von 50 kHz arbeiten. Weiterhin besitzt das CBL2 eine Buchse f{\"u}r angeblich nur einen digitalen Ein- bzw. Ausgang. An diesem Eingang wird standardm{\"a}ßig haupts{\"a}chlich der Bewegungssensor CBR betrieben. In diesem Beitrag werden Erweiterungsm{\"o}glichkeiten dieses Anschlusses beschrieben.},
  language  = {de}
}
@article{BragardBragard2012,
  author    = {Bragard, G. and Bragard, Michael},
  title     = {Ein kosteng{\"u}nstiges, universelles Modellbauinterface},
  series = {Der mathematische und naturwissenschaftliche Unterricht : MNU ; Organ des Deutschen Vereins zur F{\"o}rderung des Mathematischen und Naturwissenschaftlichen Unterrichts e.V.},
  volume    = {65},
  journal   = {Der mathematische und naturwissenschaftliche Unterricht : MNU ; Organ des Deutschen Vereins zur F{\"o}rderung des Mathematischen und Naturwissenschaftlichen Unterrichts e.V.},
  number    = {5},
  publisher = {Seeberger},
  address   = {Neuss},
  issn      = {0025-5866},
  pages     = {290 -- 293},
  year      = {2012},
  abstract  = {Wir stellen einen USB-Baustein vor, der eine kosteng{\"u}nstige und universelle M{\"o}glichkeit schafft , im Unterricht den Themenkreis Messen-Steuern-Regeln zu behandeln. Die Funktionalit{\"a}t orientiert sich am CVK-Interface der Firma Fischertechnik. Im Gegensatz zu kommerziellen L{\"o}sungen erlaubt unser Aufbau auch den preiswerten Einsatz in Gruppen- oder Einzelarbeit. Abschließend berichten wir {\"u}ber ein Beispiel aus dem Unterrichtseinsatz.},
  language  = {de}
}
@article{BragardvanHoekDeDoncker2012,
  author    = {Bragard, Michael and van Hoek, H. and De Doncker, R. W.},
  title     = {A major design step in IETO concept realization that allows overcurrent protection and pushes limits of switching performance},
  series = {IEEE transactions on power electronics},
  volume    = {27},
  journal   = {IEEE transactions on power electronics},
  number    = {9},
  publisher = {IEEE},
  address   = {New York},
  issn      = {0885-8993},
  doi       = {10.1109/TPEL.2012.2189136},
  pages     = {4163 -- 4171},
  year      = {2012},
  abstract  = {This paper presents the latest prototype of the integrated emitter turn-off thyristor concept, which potentially ranks among thyristor high-power devices like the gate turn-off thyristor and the integrated gate-commutated thyristor (IGCT). Due to modifications of the external driver stage and mechanical press-pack design optimization, this prototype allows for full device characterization. The turn-off capability was increased to 1600 A with an active silicon area of 823mm2 . This leads to a transient peak power of 672.1kW/cm² . Within this paper, measurements and concept assessment are presented and a comparison to state-of-the-art IGCT devices is provided.},
  language  = {en}
}
@article{BragardConradvanHoeketal.2011,
  author    = {Bragard, Michael and Conrad, M. and van Hoek, H. and De Doncker, R. W.},
  title     = {The integrated emitter turn-off thyristor (IETO) : an innovative thyristor-based high power semiconductor device using MOS assisted turn-off},
  series = {IEEE transactions on industry applications},
  volume    = {47},
  journal   = {IEEE transactions on industry applications},
  number    = {5},
  publisher = {IEEE},
  address   = {New York},
  issn      = {0093-9994},
  doi       = {10.1109/TIA.2011.2161432},
  pages     = {2175 -- 2182},
  year      = {2011},
  language  = {en}
}
@article{BragardSoltauThomasetal.2010,
  author    = {Bragard, Michael and Soltau, N. and Thomas, S. and De Doncker, R. W.},
  title     = {The balance of renewable sources and user demands in grids : power electronics for modular battery energy storage systems},
  series = {IEEE transactions on power electronics},
  volume    = {25},
  journal   = {IEEE transactions on power electronics},
  number    = {12},
  publisher = {IEEE},
  address   = {New York},
  issn      = {0885-8993},
  doi       = {10.1109/TPEL.2010.2085455},
  pages     = {3049 -- 3056},
  year      = {2010},
  abstract  = {The continuously growing amount of renewable sources starts compromising the stability of electrical grids. Contradictory to fossil fuel power plants, energy production of wind and photovoltaic (PV) energy is fluctuating. Although predictions have significantly improved, an outage of multi-MW offshore wind farms poses a challenging problem. One solution could be the integration of storage systems in the grid. After a short overview, this paper focuses on two exemplary battery storage systems, including the required power electronics. The grid integration, as well as the optimal usage of volatile energy reserves, is presented for a 5- kW PV system for home application, as well as for a 100- MW medium-voltage system, intended for wind farm usage. The efficiency and cost of topologies are investigated as a key parameter for large-scale integration of renewable power at medium- and low-voltage.},
  language  = {en}
}
@article{KoellenspergerBragardPlumetal.2009,
  author    = {K{\"o}llensperger, P. and Bragard, Michael and Plum, T. and De Doncker, R. W.},
  title     = {The dual GCT : new high-power device using optimized GCT technology},
  series = {IEEE transactions on industry applications},
  volume    = {45},
  journal   = {IEEE transactions on industry applications},
  number    = {5},
  issn      = {0093-9994},
  doi       = {10.1109/TIA.2009.2027364},
  pages     = {1754 -- 1762},
  year      = {2009},
  language  = {en}
}
@article{Alt1992,
  author    = {Alt, Helmut},
  title     = {Renditevergleich zwischen Immobilien und Festverzinslichen},
  series = {Die Bank},
  journal   = {Die Bank},
  number    = {H. 2},
  issn      = {0342-3182},
  pages     = {91 -- 92},
  year      = {1992},
  language  = {de}
}
@article{Alt1974,
  author    = {Alt, Helmut},
  title     = {1,45 Mrd. DM f{\"u}r die Kohlevergasung},
  series = {Energiewirtschaftliche Tagesfragen},
  volume    = {24},
  journal   = {Energiewirtschaftliche Tagesfragen},
  number    = {5},
  publisher = {VDE-Verlag},
  address   = {Berlin},
  issn      = {0720-6240},
  pages     = {243 -- 244},
  year      = {1974},
  language  = {de}
}
@article{Alt1975,
  author    = {Alt, Helmut},
  title     = {Elektro-Brikett-Zentralspeicherheizung soll die Spitzenlast der EVU schonen},
  series = {Energiewirtschaftliche Tagesfragen},
  volume    = {25},
  journal   = {Energiewirtschaftliche Tagesfragen},
  number    = {4},
  publisher = {VDE-Verlag},
  address   = {Berlin},
  issn      = {0720-6240},
  pages     = {148 -- 149},
  year      = {1975},
  language  = {de}
}
@article{Alt1974,
  author    = {Alt, Helmut},
  title     = {Ab 1975 Uranerz aus Rabbit-Lake},
  series = {Energiewirtschaftliche Tagesfragen},
  volume    = {24},
  journal   = {Energiewirtschaftliche Tagesfragen},
  number    = {1/2},
  publisher = {VDE-Verlag},
  address   = {Berlin},
  issn      = {0720-6240},
  pages     = {34},
  year      = {1974},
  language  = {de}
}
@article{HoltrupSadeghfamHeuermannetal.2014,
  author    = {Holtrup, S. and Sadeghfam, Arash and Heuermann, Holger and Awakowicz, P.},
  title     = {Characterization and optimization technique for microwave-driven high-intensity discharge lamps using hot S-parameters},
  series = {IEEE transactions on microwave theories and techniques},
  volume    = {62},
  journal   = {IEEE transactions on microwave theories and techniques},
  number    = {10},
  publisher = {IEEE},
  address   = {New York},
  issn      = {0018-9480},
  doi       = {10.1109/TMTT.2014.2342652},
  pages     = {2471 -- 2480},
  year      = {2014},
  abstract  = {High-intensity discharge lamps can be driven by radio-frequency signals in the ISM frequency band at 2.45 GHz, using a matching network to transform the impedance of the plasma to the source impedance. To achieve an optimal operating condition, a good characterization of the lamp in terms of radio frequency equivalent circuits under operating conditions is necessary, enabling the design of an efficient matching network. This paper presents the characterization technique for such lamps and presents the design of the required matching network. For the characterization, a high-intensity discharge lamp was driven by a monofrequent large signal at 2.45 GHz, whereas a frequency sweep over 300 MHz was performed across this signal to measure so-called small-signal hot S-parameters using a vector network analyzer. These parameters are then used as an equivalent load in a circuit simulator to design an appropriate matching network. Using the measured data as a black-box model in the simulation results in a quick and efficient method to simulate and design efficient matching networks in spite of the complex plasma behavior. Furthermore, photometric analysis of high-intensity discharge lamps are carried out, comparing microwave operation to conventional operation.},
  language  = {en}
}
@article{AlhwarinFerreinScholl2014,
  author    = {Alhwarin, Faraj and Ferrein, Alexander and Scholl, Ingrid},
  title     = {IR stereo kinect: improving depth images by combining structured light with IR stereo},
  pages     = {1 -- 9},
  year      = {2014},
  language  = {en}
}
@article{WolfBiesenGreeb2014,
  author    = {Wolf, Martin and Biesen, Ina van der and Greeb, Birgit},
  title     = {Mein Freund, die Uni},
  series = {Die neue Hochschule : DNH : f{\"u}r anwendungsbezogene Wissenschaft und Kunst},
  volume    = {2014},
  journal   = {Die neue Hochschule : DNH : f{\"u}r anwendungsbezogene Wissenschaft und Kunst},
  number    = {2},
  publisher = {HLB},
  address   = {Bonn},
  issn      = {0340-448X},
  pages     = {54 -- 56},
  year      = {2014},
  language  = {de}
}
@article{Ferrein2008,
  author    = {Ferrein, Alexander},
  title     = {Towards applying soccer moves in the RoboCup Standard Platform League},
  series = {{\"O}GAI-Journal},
  volume    = {Bd. 27},
  journal   = {{\"O}GAI-Journal},
  number    = {H. 3},
  organization    = {{\"O}sterreichische Gesellschaft f{\"u}r Artificial Intelligence},
  issn      = {0254-4326},
  pages     = {4 -- 9},
  year      = {2008},
  language  = {en}
}
@article{Ferrein2004,
  author    = {Ferrein, Alexander},
  title     = {Autonome Entscheidungsfindung bei Robotern : Planwirtschaft},
  series = {Linux-Magazin},
  journal   = {Linux-Magazin},
  number    = {7},
  issn      = {1432-640X (Print)},
  pages     = {50 -- 53},
  year      = {2004},
  language  = {de}
}
@article{FerreinSteinbauerMcPhillipsetal.2009,
  author    = {Ferrein, Alexander and Steinbauer, Gerald and McPhillips, Graeme and Niem{\"u}ller, Tim and Potgieter, Anet},
  title     = {Team Zadeat 2009 : team report},
  volume    = {6},
  pages     = {1},
  year      = {2009},
  language  = {en}
}
@article{FerreinNiemuellerSteinbauer2010,
  author    = {Ferrein, Alexander and Niem{\"u}ller, Tim and Steinbauer, Gerald},
  title     = {Team Zadeat 2010 : application for participation},
  pages     = {5 Seiten},
  year      = {2010},
  language  = {en}
}
@article{BeckBuchleitnerFerreinetal.2014,
  author    = {Beck, Daniel and Buchleitner, Martin and Ferrein, Alexander and Niem{\"u}ller, Tim and Steinbauer, Gerald},
  title     = {Mostly Harmless \& AllemaniACs - mixed innovations},
  pages     = {1 -- 8},
  year      = {2014},
  language  = {en}
}
@article{VorstFerreinLakemeyer2006,
  author    = {Vorst, Phillip and Ferrein, Alexander and Lakemeyer, Gerhard},
  title     = {AllemaniACs3D team description},
  pages     = {1 -- 6},
  year      = {2006},
  language  = {en}
}
@article{FerreinSteinbauerMcPhillipsetal.2007,
  author    = {Ferrein, Alexander and Steinbauer, Gerald and McPhillips, Graeme and Potgieter, Anet},
  title     = {Establishing the RoboCup Standard League in Africa - applying for the RoboCup Standard League with a German-Austrian-South African Research Project},
  pages     = {1 -- 5},
  year      = {2007},
  language  = {en}
}
@article{FerreinSteinbauerMcPhillipsetal.2008,
  author    = {Ferrein, Alexander and Steinbauer, Gerald and McPhillips, Graeme and Potgieter, Anet},
  title     = {RoboCup Standard Platform League - Team Zadeat : an intercontinental research effort},
  pages     = {1 -- 7},
  year      = {2008},
  language  = {en}
}
@article{Gligorevic2013,
  author    = {Gligorevic, Snjezana},
  title     = {Airport surface propagation channel in the C-Band: measurements and modeling},
  series = {IEEE transactions on antennas and propagation},
  volume    = {Vol. 61},
  journal   = {IEEE transactions on antennas and propagation},
  number    = {Iss. 9},
  publisher = {IEEE},
  address   = {New York},
  issn      = {0018-926x},
  pages     = {4792 -- 4802},
  year      = {2013},
  language  = {en}
}
@article{Gligorevic2008,
  author    = {Gligorevic, Snjezana},
  title     = {Joint channel estimation and equalisation of fast time-varying frequency-selective channels},
  series = {European transactions on telecommunications},
  volume    = {Vol. 19},
  journal   = {European transactions on telecommunications},
  number    = {Iss. 1},
  issn      = {1541-8251; 2161-3915; 1120-3862; 1124-318X},
  pages     = {1 -- 13},
  year      = {2008},
  language  = {en}
}
@article{BrueckSorgerGligorevicetal.2000,
  author    = {Br{\"u}ck, Stefan and Sorger, Ulrich and Gligorevic, Snjezana and Stolte, Norbert},
  title     = {Interleaving for outer convolutional codes in DS-CDMA systems},
  series = {IEEE transactions on communications},
  volume    = {Vol. 48},
  journal   = {IEEE transactions on communications},
  number    = {Iss. 7},
  issn      = {0090-6778},
  pages     = {1100 -- 1107},
  year      = {2000},
  language  = {en}
}
@article{Alt1976,
  author    = {Alt, Helmut},
  title     = {Spannungs-Blindleistungs-Regelung mit gesteuerten Netzkennlinien},
  series = {Elektrotechnische Zeitschrift : Ausgabe A, Zeitschrift f{\"u}r elektrische Energietechnik : ETZ},
  volume    = {97},
  journal   = {Elektrotechnische Zeitschrift : Ausgabe A, Zeitschrift f{\"u}r elektrische Energietechnik : ETZ},
  number    = {7},
  publisher = {VDE-Verlag},
  address   = {Wuppertal},
  issn      = {0302-265x},
  pages     = {441 -- 446},
  year      = {1976},
  language  = {de}
}
@article{Alt2011,
  author    = {Alt, Helmut},
  title     = {Die Sonne bestimmt zunehmend die Spannung in der Steckdose : Lastflussberechnung einer Photovoltaikeinspeisung},
  series = {EW : das Magazin f{\"u}r die Energie-Wirtschaft},
  volume    = {Bd. 110},
  journal   = {EW : das Magazin f{\"u}r die Energie-Wirtschaft},
  number    = {H. 17/18},
  publisher = {VWEW-Energieverlag},
  address   = {Frankfurt, M.},
  issn      = {0013-5496},
  pages     = {24 -- 29},
  year      = {2011},
  language  = {de}
}
@article{Alt2005,
  author    = {Alt, Helmut},
  title     = {Versorgungssicherheit und Windenergie : Tatsachen und Fakten statt Mythen und Mysterien},
  series = {EW : das Magazin f{\"u}r die Energie-Wirtschaft},
  volume    = {Bd. 104},
  journal   = {EW : das Magazin f{\"u}r die Energie-Wirtschaft},
  number    = {H. 25},
  issn      = {0013-5496},
  pages     = {42 -- 45},
  year      = {2005},
  language  = {de}
}
@article{Alt2005,
  author    = {Alt, Helmut},
  title     = {Wunschphantasie eines eingefleischten Kernenergiegegners : zur Rede von Bundesumweltminister J{\"u}rgen Trittin auf dem VDEW-Kongress 2005 "Die Energieversorgung der Zukunft"},
  series = {EW : das Magazin f{\"u}r die Energie-Wirtschaft},
  volume    = {Bd. 104},
  journal   = {EW : das Magazin f{\"u}r die Energie-Wirtschaft},
  number    = {H. 17/18},
  issn      = {0013-5496},
  pages     = {7},
  year      = {2005},
  language  = {de}
}
@article{Alt2002,
  author    = {Alt, Helmut},
  title     = {Belieferung von Kunden in fremden Netzgebieten},
  series = {EW : das Magazin f{\"u}r die Energie-Wirtschaft},
  volume    = {Bd. 101},
  journal   = {EW : das Magazin f{\"u}r die Energie-Wirtschaft},
  number    = {H. 1/2},
  issn      = {0013-5496},
  pages     = {26 -- 35},
  year      = {2002},
  language  = {de}
}
@article{Alt1989,
  author    = {Alt, Helmut},
  title     = {Einfluß der Kontof{\"u}hrungsmodelle auf den Effektivzins und die Restschuld bei Annuit{\"a}tendarlehen},
  series = {Betriebs-Berater : BB : Beil. 14 Finanz-Berater},
  journal   = {Betriebs-Berater : BB : Beil. 14 Finanz-Berater},
  issn      = {0340-7926},
  pages     = {32 -- 37},
  year      = {1989},
  language  = {de}
}
@article{Alt1989,
  author    = {Alt, Helmut},
  title     = {Die Bedeutung des Effektivzinses in der Finanzwirtschaft},
  series = {Betriebs-Berater : BB : Beil. 14 Finanz-Berater},
  journal   = {Betriebs-Berater : BB : Beil. 14 Finanz-Berater},
  issn      = {0340-7926},
  pages     = {31 -- 32},
  year      = {1989},
  language  = {de}
}
@article{Alt2000,
  author    = {Alt, Helmut},
  title     = {Benchmark der Netznutzungspreise},
  series = {Energiewirtschaftliche Tagesfragen : et ; Zeitschrift f{\"u}r Energiewirtschaft, Recht, Technik und Umwelt},
  volume    = {Bd. 50},
  journal   = {Energiewirtschaftliche Tagesfragen : et ; Zeitschrift f{\"u}r Energiewirtschaft, Recht, Technik und Umwelt},
  number    = {H. 11},
  issn      = {0013-743X},
  pages     = {846 -- 850},
  year      = {2000},
  language  = {de}
}
@article{Alt1995,
  author    = {Alt, Helmut},
  title     = {Netzanschlußm{\"o}glichkeiten und energiewirtschaftliche Bewertung von Windkraftanlagen},
  series = {Elektrizit{\"a}tswirtschaft},
  volume    = {Jg. 94},
  journal   = {Elektrizit{\"a}tswirtschaft},
  number    = {H. 19},
  issn      = {0013-5496},
  pages     = {1224 -- 1234},
  year      = {1995},
  language  = {de}
}
@article{Alt1995,
  author    = {Alt, Helmut},
  title     = {Netzimpedanz- und Oberschwingungsberechnung in Netzen der {\"o}ffentlichen Stromversorgung},
  series = {Elektrizit{\"a}tswirtschaft},
  volume    = {Bd. 94},
  journal   = {Elektrizit{\"a}tswirtschaft},
  number    = {H. 4},
  issn      = {0013-5496},
  pages     = {166 -- 174},
  year      = {1995},
  language  = {de}
}