@article{DachwaldOhndorf2007,
  author    = {Dachwald, Bernd and Ohndorf, A.},
  title     = {1st ACT Global Trajectory Optimisation Competition : Results found at DLR},
  series = {Acta Astronautica. 61 (2007), H. 9},
  journal   = {Acta Astronautica. 61 (2007), H. 9},
  isbn      = {0094-5765},
  pages     = {742 -- 752},
  year      = {2007},
  language  = {en}
}
@article{KreyerMuellerEsch2020,
  author    = {Kreyer, J{\"o}rg and M{\"u}ller, Marvin and Esch, Thomas},
  title     = {A Calculation Methodology for Predicting Exhaust Mass Flows and Exhaust Temperature Profiles for Heavy-Duty Vehicles},
  series = {SAE International Journal of Commercial Vehicles},
  volume    = {13},
  journal   = {SAE International Journal of Commercial Vehicles},
  number    = {2},
  publisher = {SAE International},
  address   = {Warrendale, Pa.},
  issn      = {1946-3928},
  doi       = {10.4271/02-13-02-0009},
  pages     = {129 -- 143},
  year      = {2020},
  abstract  = {The predictive control of commercial vehicle energy management systems, such as vehicle thermal management or waste heat recovery (WHR) systems, are discussed on the basis of information sources from the field of environment recognition and in combination with the determination of the vehicle system condition. In this article, a mathematical method for predicting the exhaust gas mass flow and the exhaust gas temperature is presented based on driving data of a heavy-duty vehicle. The prediction refers to the conditions of the exhaust gas at the inlet of the exhaust gas recirculation (EGR) cooler and at the outlet of the exhaust gas aftertreatment system (EAT). The heavy-duty vehicle was operated on the motorway to investigate the characteristic operational profile. In addition to the use of road gradient profile data, an evaluation of the continuously recorded distance signal, which represents the distance between the test vehicle and the road user ahead, is included in the prediction model. Using a Fourier analysis, the trajectory of the vehicle speed is determined for a defined prediction horizon. To verify the method, a holistic simulation model consisting of several hierarchically structured submodels has been developed. A map-based submodel of a combustion engine is used to determine the EGR and EAT exhaust gas mass flows and exhaust gas temperature profiles. All simulation results are validated on the basis of the recorded vehicle and environmental data. Deviations from the predicted values are analyzed and discussed.},
  language  = {en}
}
@article{DachwaldTsinas1994,
  author    = {Dachwald, Bernd and Tsinas, L.},
  title     = {A combined neural and genetic learning algorithm / Tsinas, L. ; Dachwald, B.},
  series = {Proceedings of the First IEEE Conference on Evolutionary Computation, 1994. IEEE World Congress on Computational Intelligence.},
  journal   = {Proceedings of the First IEEE Conference on Evolutionary Computation, 1994. IEEE World Congress on Computational Intelligence.},
  address   = {Orlando, Fl},
  isbn      = {0-7803-1899-4},
  pages     = {770 -- 774},
  year      = {1994},
  language  = {en}
}
@article{GerhardtCooperWhitbreadetal.1985,
  author    = {Gerhardt, Hans Joachim and Cooper, K.-R. and Whitbread, R. and Gary, K.-P. (u.a.)},
  title     = {A comparison of aerodynamic drag measurements on model trucks in closed-jet and open-jet wind tunnels},
  pages     = {261 -- 274},
  year      = {1985},
  language  = {en}
}
@article{Harder1999,
  author    = {Harder, J{\"o}rn},
  title     = {A crystallographic model for the study of local deformation processes in polycrystals},
  series = {International journal of plasticity. 15 (1999), H. 6},
  journal   = {International journal of plasticity. 15 (1999), H. 6},
  isbn      = {0749-6419},
  pages     = {605 -- 624},
  year      = {1999},
  language  = {en}
}
@article{SchmitzRoetertPischinger1988,
  author    = {Schmitz, G{\"u}nter and Roetert, J. and Pischinger, M.},
  title     = {A Fast Intelligent VMEbus System for Combustion Analysis in Engines},
  series = {19th [nineteenth] International Symposium on Automotive Technology \& [and] Automation : with particular reference to cell control and quality management systems for the manufacturing industries; Monte Carlo, 24. - 28. October 1988.},
  journal   = {19th [nineteenth] International Symposium on Automotive Technology \& [and] Automation : with particular reference to cell control and quality management systems for the manufacturing industries; Monte Carlo, 24. - 28. October 1988.},
  publisher = {Automotive Automation Ltd},
  address   = {Croydon},
  isbn      = {0947719229},
  pages     = {381 -- 391},
  year      = {1988},
  language  = {en}
}
@article{WeberArentMuenchetal.2016,
  author    = {Weber, Tobias and Arent, Jan-Christoph and M{\"u}nch, Lukas and Duhovic, Miro and Balvers, Johannes M.},
  title     = {A fast method for the generation of boundary conditions for thermal autoclave simulation},
  series = {Composites Part A},
  volume    = {88},
  journal   = {Composites Part A},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1359-835X},
  doi       = {10.1016/j.compositesa.2016.05.036},
  pages     = {216 -- 225},
  year      = {2016},
  abstract  = {Manufacturing process simulation enables the evaluation and improvement of autoclave mold concepts early in the design phase. To achieve a high part quality at low cycle times, the thermal behavior of the autoclave mold can be investigated by means of simulations. Most challenging for such a simulation is the generation of necessary boundary conditions. Heat-up and temperature distribution in an autoclave mold are governed by flow phenomena, tooling material and shape, position within the autoclave, and the chosen autoclave cycle. This paper identifies and summarizes the most important factors influencing mold heat-up and how they can be introduced into a thermal simulation. Thermal measurements are used to quantify the impact of the various parameters. Finally, the gained knowledge is applied to develop a semi-empirical approach for boundary condition estimation that enables a simple and fast thermal simulation of the autoclave curing process with reasonably high accuracy for tooling optimization.},
  language  = {en}
}
@article{UlmerBraunChengetal.2023,
  author    = {Ulmer, Jessica and Braun, Carsten and Cheng, Chi-Tsun and Dowey, Steve and Wollert, J{\"o}rg},
  title     = {A human factors-aware assistance system in manufacturing based on gamification and hardware modularisation},
  series = {International Journal of Production Research},
  journal   = {International Journal of Production Research},
  publisher = {Taylor \& Francis},
  issn      = {0020-7543 (Print)},
  doi       = {10.1080/00207543.2023.2166140},
  year      = {2023},
  abstract  = {Assistance systems have been widely adopted in the manufacturing sector to facilitate various processes and tasks in production environments. However, existing systems are mostly equipped with rigid functional logic and do not provide individual user experiences or adapt to their capabilities. This work integrates human factors in assistance systems by adjusting the hardware and instruction presented to the workers' cognitive and physical demands. A modular system architecture is designed accordingly, which allows a flexible component exchange according to the user and the work task. Gamification, the use of game elements in non-gaming contexts, has been further adopted in this work to provide level-based instructions and personalised feedback. The developed framework is validated by applying it to a manual workstation for industrial assembly routines.},
  language  = {en}
}
@article{KonstantinidisFloresMartinezDachwaldetal.2015,
  author    = {Konstantinidis, Konstantinos and Flores Martinez, Claudio and Dachwald, Bernd and Ohndorf, Andreas and Dykta, Paul and Bowitz, Pascal and Rudolph, Martin and Digel, Ilya and Kowalski, Julia and Voigt, Konstantin and F{\"o}rstner, Roger},
  title     = {A lander mission to probe subglacial water on Saturn's moon enceladus for life},
  series = {Acta astronautica},
  volume    = {Vol. 106},
  journal   = {Acta astronautica},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1879-2030 (E-Journal); 0094-5765 (Print)},
  pages     = {63 -- 89},
  year      = {2015},
  language  = {en}
}
@article{DittusTuryshevDachwaldetal.2005,
  author    = {Dittus, H. and Turyshev, S. G. and Dachwald, Bernd and Blome, Hans-Joachim},
  title     = {A Mission to Explore the Pioneer Anomaly},
  series = {Proceedings of the 39th ESLAB Symposium "Trends in Space Science and Cosmic Vision 2020" : 19 - 21 April 2005, ESTEC, Noordwijk, the Netherlands / European Space Agency. [Comp. by: F. Favata ...] . - (ESA SP ; 588)},
  journal   = {Proceedings of the 39th ESLAB Symposium "Trends in Space Science and Cosmic Vision 2020" : 19 - 21 April 2005, ESTEC, Noordwijk, the Netherlands / European Space Agency. [Comp. by: F. Favata ...] . - (ESA SP ; 588)},
  publisher = {ESA Publ. Div.},
  address   = {Noordwijk},
  isbn      = {9290928999},
  pages     = {3 -- 10},
  year      = {2005},
  language  = {en}
}
@article{KhayyamJamaliBabHadiasharetal.2020,
  author    = {Khayyam, Hamid and Jamali, Ali and Bab-Hadiashar, Alireza and Esch, Thomas and Ramakrishna, Seeram and Jalili, Mahdi and Naebe, Minoo},
  title     = {A Novel Hybrid Machine Learning Algorithm for Limited and Big Data Modeling with Application in Industry 4.0},
  series = {IEEE Access},
  volume    = {8},
  journal   = {IEEE Access},
  number    = {Art. 9108222},
  publisher = {IEEE},
  address   = {New York, NY},
  issn      = {2169-3536},
  doi       = {10.1109/ACCESS.2020.2999898},
  pages     = {111381 -- 111393},
  year      = {2020},
  abstract  = {To meet the challenges of manufacturing smart products, the manufacturing plants have been radically changed to become smart factories underpinned by industry 4.0 technologies. The transformation is assisted by employment of machine learning techniques that can deal with modeling both big or limited data. This manuscript reviews these concepts and present a case study that demonstrates the use of a novel intelligent hybrid algorithms for Industry 4.0 applications with limited data. In particular, an intelligent algorithm is proposed for robust data modeling of nonlinear systems based on input-output data. In our approach, a novel hybrid data-driven combining the Group-Method of Data-Handling and Singular-Value Decomposition is adapted to find an offline deterministic model combined with Pareto multi-objective optimization to overcome the overfitting issue. An Unscented-Kalman-Filter is also incorporated to update the coefficient of the deterministic model and increase its robustness against data uncertainties. The effectiveness of the proposed method is examined on a set of real industrial measurements.},
  language  = {en}
}
@article{KhayyamJamaliBabHadiasharetal.2020,
  author    = {Khayyam, Hamid and Jamali, Ali and Bab-Hadiashar, Alireza and Esch, Thomas and Ramakrishna, Seeram and Jalil, Mahdi and Naebe, Minoo},
  title     = {A Novel Hybrid Machine Learning Algorithm for Limited and Big Data Modelling with Application in Industry 4.0},
  series = {IEEE Access},
  journal   = {IEEE Access},
  publisher = {IEEE},
  address   = {New York, NY},
  isbn      = {2169-3536},
  doi       = {10.1109/ACCESS.2020.2999898},
  pages     = {1 -- 12},
  year      = {2020},
  abstract  = {To meet the challenges of manufacturing smart products, the manufacturing plants have been radically changed to become smart factories underpinned by industry 4.0 technologies. The transformation is assisted by employment of machine learning techniques that can deal with modeling both big or limited data. This manuscript reviews these concepts and present a case study that demonstrates the use of a novel intelligent hybrid algorithms for Industry 4.0 applications with limited data. In particular, an intelligent algorithm is proposed for robust data modeling of nonlinear systems based on input-output data. In our approach, a novel hybrid data-driven combining the Group-Method of Data-Handling and Singular-Value Decomposition is adapted to find an offline deterministic model combined with Pareto multi-objective optimization to overcome the overfitting issue. An Unscented-Kalman-Filter is also incorporated to update the coefficient of the deterministic model and increase its robustness against data uncertainties. The effectiveness of the proposed method is examined on a set of real industrial measurements.},
  language  = {en}
}
@article{BoehnischBraunMuscarelloetal.2023,
  author    = {B{\"o}hnisch, Nils and Braun, Carsten and Muscarello, Vincenzo and Marzocca, Pier},
  title     = {A sensitivity study on aeroelastic instabilities of slender wings with a large propeller},
  series = {AIAA SCITECH 2023 Forum},
  journal   = {AIAA SCITECH 2023 Forum},
  publisher = {AIAA},
  doi       = {10.2514/6.2023-1893},
  pages     = {1 -- 14},
  year      = {2023},
  abstract  = {Next-generation aircraft designs often incorporate multiple large propellers attached along the wingspan. These highly flexible dynamic systems can exhibit uncommon aeroelastic instabilities, which should be carefully investigated to ensure safe operation. The interaction between the propeller and the wing is of particular importance. It is known that whirl flutter is stabilized by wing motion and wing aerodynamics. This paper investigates the effect of a propeller onto wing flutter as a function of span position and mounting stiffness between the propeller and wing. The analysis of a comparison between a tractor and pusher configuration has shown that the coupled system is more stable than the standalone wing for propeller positions near the wing tip for both configurations. The wing fluttermechanism is mostly affected by the mass of the propeller and the resulting change in eigenfrequencies of the wing. For very weak mounting stiffnesses, whirl flutter occurs, which was shown to be stabilized compared to a standalone propeller due to wing motion. On the other hand, the pusher configuration is, as to be expected, the more critical configuration due to the attached mass behind the elastic axis.},
  language  = {de}
}
@article{DachwaldBallUlamecetal.2009,
  author    = {Dachwald, Bernd and Ball, Andrew J. and Ulamec, Stephan and Price, Michael E.},
  title     = {A small mission for in situ exploration of a primitive binary near-Earth asteroid / Ball, Andrew J. ; Ulamec, Stephan ; Dachwald, Bernd ; Price, Michael E. ; [u.a.]},
  series = {Advances in Space Research. 43 (2009), H. 2},
  journal   = {Advances in Space Research. 43 (2009), H. 2},
  publisher = {Elsevier},
  address   = {Amsterdam},
  isbn      = {0273-1177},
  pages     = {317 -- 324},
  year      = {2009},
  language  = {en}
}
@article{BoehnischBraunMuscarelloetal.2024,
  author    = {B{\"o}hnisch, Nils and Braun, Carsten and Muscarello, Vincenzo and Marzocca, Pier},
  title     = {About the wing and whirl flutter of a slender wing-propeller system},
  series = {Journal of Aircraft},
  journal   = {Journal of Aircraft},
  publisher = {American Institute of Aeronautics and Astronautics},
  issn      = {1533-3868},
  doi       = {10.2514/1.C037542},
  pages     = {1 -- 14},
  year      = {2024},
  abstract  = {Next-generation aircraft designs often incorporate multiple large propellers attached along the wingspan (distributed electric propulsion), leading to highly flexible dynamic systems that can exhibit aeroelastic instabilities. This paper introduces a validated methodology to investigate the aeroelastic instabilities of wing-propeller systems and to understand the dynamic mechanism leading to wing and whirl flutter and transition from one to the other. Factors such as nacelle positions along the wing span and chord and its propulsion system mounting stiffness are considered. Additionally, preliminary design guidelines are proposed for flutter-free wing-propeller systems applicable to novel aircraft designs. The study demonstrates how the critical speed of the wing-propeller systems is influenced by the mounting stiffness and propeller position. Weak mounting stiffnesses result in whirl flutter, while hard mounting stiffnesses lead to wing flutter. For the latter, the position of the propeller along the wing span may change the wing mode shapes and thus the flutter mechanism. Propeller positions closer to the wing tip enhance stability, but pusher configurations are more critical due to the mass distribution behind the elastic axis.},
  language  = {en}
}
@article{MertensKlevenhusenJakob1987,
  author    = {Mertens, Josef and Klevenhusen, K. D. and Jakob, H.},
  title     = {Accurate Transonic Wave Drag Prediction Using Simple Physical Models},
  series = {AIAA-Journal. 25 (1987), H. 6},
  journal   = {AIAA-Journal. 25 (1987), H. 6},
  isbn      = {0001-1452},
  pages     = {799 -- 805},
  year      = {1987},
  language  = {en}
}
@article{MertensHenke2001,
  author    = {Mertens, Josef and Henke, Rolf},
  title     = {Adaptive technologies for future civil air transport},
  series = {Air \& Space Europe. 3 (2001), H. 3-4},
  journal   = {Air \& Space Europe. 3 (2001), H. 3-4},
  isbn      = {1247-5793},
  pages     = {80 -- 82},
  year      = {2001},
  language  = {en}
}
@article{SchulzeFeyerlPischinger2023,
  author    = {Schulze, Sven and Feyerl, G{\"u}nter and Pischinger, Stefan},
  title     = {Advanced ECMS for hybrid electric heavy-duty trucks with predictive battery discharge and adaptive operating strategy under real driving conditions},
  series = {Energies},
  volume    = {16},
  journal   = {Energies},
  number    = {13},
  publisher = {MDPI},
  address   = {Basel},
  issn      = {1996-1073},
  doi       = {10.3390/en16135171},
  pages     = {29 Seiten, Art. Nr.: 5171},
  year      = {2023},
  abstract  = {To fulfil the CO2 emission reduction targets of the European Union (EU), heavy-duty (HD) trucks need to operate 15\% more efficiently by 2025 and 30\% by 2030. Their electrification is necessary as conventional HD trucks are already optimized for the long-haul application. The resulting hybrid electric vehicle (HEV) truck gains most of the fuel saving potential by the recuperation of potential energy and its consecutive utilization. The key to utilizing the full potential of HEV-HD trucks is to maximize the amount of recuperated energy and ensure its intelligent usage while keeping the operating point of the internal combustion engine as efficient as possible. To achieve this goal, an intelligent energy management strategy (EMS) based on ECMS is developed for a parallel HEV-HD truck which uses predictive discharge of the battery and adaptive operating strategy regarding the height profile and the vehicle mass. The presented EMS can reproduce the global optimal operating strategy over long phases and lead to a fuel saving potential of up to 2\% compared with a heuristic strategy. Furthermore, the fuel saving potential is correlated with the investigated boundary conditions to deepen the understanding of the impact of intelligent EMS for HEV-HD trucks.},
  language  = {en}
}
@article{WeberRuffStahl2017,
  author    = {Weber, Tobias and Ruff-Stahl, Hans-Joachim K.},
  title     = {Advances in Composite Manufacturing of Helicopter Parts},
  series = {International Journal of Aviation, Aeronautics, and Aerospace},
  volume    = {4},
  journal   = {International Journal of Aviation, Aeronautics, and Aerospace},
  number    = {1},
  issn      = {2374-6793},
  doi       = {10.15394/ijaaa.2017.1153},
  year      = {2017},
  language  = {en}
}
@article{GoettenHavermannBraunetal.2021,
  author    = {G{\"o}tten, Falk and Havermann, Marc and Braun, Carsten and Marino, Matthew and Bil, Cees},
  title     = {Aerodynamic Investigations of UAV Sensor Turrets - A Combined Wind-tunnel and CFD Approach},
  series = {SciTech 2021, AIAA SciTech Forum, online, WW, Jan 11-15, 2021},
  journal   = {SciTech 2021, AIAA SciTech Forum, online, WW, Jan 11-15, 2021},
  publisher = {AIAA},
  address   = {Reston, Va.},
  doi       = {10.2514/6.2021-1535},
  pages     = {1 -- 12},
  year      = {2021},
  language  = {en}
}
@article{GerhardtKonrathKrameretal.1992,
  author    = {Gerhardt, Hans Joachim and Konrath, B. and Kramer, C. and Oliveira, L.-A.},
  title     = {Aerodynamische Abdichtung von Anlagen f{\"u}r die Bandbearbeitung},
  series = {Blech, Rohre, Profile. 39 (1992), H. 1},
  journal   = {Blech, Rohre, Profile. 39 (1992), H. 1},
  isbn      = {0006-4688},
  pages     = {39 -- 1},
  year      = {1992},
  language  = {de}
}
@article{Mertens1998,
  author    = {Mertens, Josef},
  title     = {Aerodynamische Ziele des Adaptiven Fl{\"u}gels (ADIF).},
  series = {DGLR-Jahrbuch 1998 Bd. 1},
  journal   = {DGLR-Jahrbuch 1998 Bd. 1},
  pages     = {47 -- 52},
  year      = {1998},
  language  = {de}
}
@article{GerhardtKramer1985,
  author    = {Gerhardt, Hans Joachim and Kramer, C.},
  title     = {Aerodynamsiche RA-Optimierung},
  series = {Zentralblatt fuer Industriebau. 31 (1985), H. 5},
  journal   = {Zentralblatt fuer Industriebau. 31 (1985), H. 5},
  isbn      = {0044-4227},
  pages     = {358 -- 362},
  year      = {1985},
  language  = {en}
}
@article{GoettenHavermannBraunetal.2020,
  author    = {G{\"o}tten, Falk and Havermann, Marc and Braun, Carsten and Marino, Matthew and Bil, Cees},
  title     = {Airfoil drag at low-to-medium reynolds numbers: A novel estimation method},
  series = {AIAA Journal},
  volume    = {58},
  journal   = {AIAA Journal},
  number    = {7},
  publisher = {AIAA},
  address   = {Reston, Va.},
  issn      = {1533-385X},
  doi       = {10.2514/1.J058983},
  pages     = {2791 -- 2805},
  year      = {2020},
  abstract  = {This paper presents a novel method for airfoil drag estimation at Reynolds numbers between 4×10⁵ and 4×10⁶. The novel method is based on a systematic study of 40 airfoils applying over 600 numerical simulations and considering natural transition. The influence of the airfoil thickness-to-chord ratio, camber, and freestream Reynolds number on both friction and pressure drag is analyzed in detail. Natural transition significantly affects drag characteristics and leads to distinct drag minima for different Reynolds numbers and thickness-to-chord ratios. The results of the systematic study are used to develop empirical correlations that can accurately predict an airfoil drag at low-lift conditions. The new approach estimates a transition location based on airfoil thickness-to-chord ratio, camber, and Reynolds number. It uses the transition location in a mixed laminar-turbulent skin-friction calculation, and corrects the skin-friction coefficient for separation effects. Pressure drag is estimated separately based on correlations of thickness-to-chord ratio, camber, and Reynolds number. The novel method shows excellent accuracy when compared with wind-tunnel measurements of multiple airfoils. It is easily integrable into existing aircraft design environments and is highly beneficial in the conceptual design stage.},
  language  = {en}
}
@article{Maurischat2022,
  author    = {Maurischat, Andreas},
  title     = {Algebraic independence of the Carlitz period and its hyperderivatives},
  series = {Journal of Number Theory},
  volume    = {240},
  journal   = {Journal of Number Theory},
  publisher = {Elsevier},
  address   = {Orlando, Fla.},
  issn      = {0022-314X},
  doi       = {10.1016/j.jnt.2022.01.006},
  pages     = {145 -- 162},
  year      = {2022},
  language  = {en}
}
@article{Maurischat2021,
  author    = {Maurischat, Andreas},
  title     = {Algebraic independence of the Carlitz period and its hyperderivatives},
  pages     = {1 -- 12},
  year      = {2021},
  language  = {en}
}
@article{WeiheErnstRoethetal.2013,
  author    = {Weihe, Stefan and Ernst, Ansgar and R{\"o}th, Thilo and Proksch, Johannes},
  title     = {Aluminium-Stahl-Verbundguss im Nutzfahrzeugbau},
  series = {ATZ - Automobiltechnische Zeitschrift},
  volume    = {115},
  journal   = {ATZ - Automobiltechnische Zeitschrift},
  number    = {4},
  publisher = {Springer Fachmedien Wiesbaden},
  issn      = {2192-8800 (Online)},
  pages     = {312 -- 316},
  year      = {2013},
  abstract  = {In modernen Fahrzeugkarosserien der Großserie kommen zunehmend Materialmischbauweisen zur Anwendung. In Zusammenarbeit der Daimler AG, der Tower Automotive Holding GmbH, der Imperia GmbH sowie der Partnerunternehmen KSM Castings GmbH und Schaufler Tooling GmbH \& Co. KG wird das Leichtbaupotenzial von Aluminiumverbundguss-Stahlblech-Hybriden am Beispiel des vorderen Dachquertr{\"a}gers des Mercedes-Benz Viano/Vito ausf{\"u}hrlich untersucht.},
  language  = {de}
}
@article{SchaelAtanasyanBerdugoetal.2019,
  author    = {Schael, S. and Atanasyan, A. and Berdugo, J. and Bretz, T. and Czupalla, Markus and Dachwald, Bernd and Doetinchem, P. von and Duranti, M. and Gast, H. and Karpinski, W. and Kirn, T. and L{\"u}belsmeyer, K. and Ma{\~n}a, C. and Marrocchesi, P.S. and Mertsch, P. and Moskalenko, I.V. and Schervan, T. and Schluse, M. and Schr{\"o}der, K.-U. and Schultz von Dratzig, A. and Senatore, C. and Spies, L. and Wakely, S.P. and Wlochal, M. and Uglietti, D. and Zimmermann, J.},
  title     = {AMS-100: The next generation magnetic spectrometer in space - An international science platform for physics and astrophysics at Lagrange point 2},
  series = {Nuclear Instruments and Methods in Physics Research Section A: Accelerators, Spectrometers, Detectors and Associated Equipment},
  volume    = {944},
  journal   = {Nuclear Instruments and Methods in Physics Research Section A: Accelerators, Spectrometers, Detectors and Associated Equipment},
  number    = {162561},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0168-9002},
  doi       = {10.1016/j.nima.2019.162561},
  year      = {2019},
  language  = {en}
}
@article{WeberEnglhardArentetal.2019,
  author    = {Weber, Tobias and Englhard, Markus and Arent, Jan-Christoph and Hausmann, Joachim},
  title     = {An experimental characterization of wrinkling generated during prepreg autoclave manufacturing using caul plates},
  series = {Journal of Composite Materials},
  volume    = {53},
  journal   = {Journal of Composite Materials},
  number    = {26-27},
  issn      = {1530-793X},
  doi       = {10.1177/0021998319846556},
  pages     = {3757 -- 3773},
  year      = {2019},
  language  = {en}
}
@article{FunkeBeckmannAbanteriba2019,
  author    = {Funke, Harald and Beckmann, Nils and Abanteriba, Sylvester},
  title     = {An overview on dry low NOx micromix combustor development for hydrogen-rich gas turbine applications},
  series = {International Journal of Hydrogen Energy},
  volume    = {44},
  journal   = {International Journal of Hydrogen Energy},
  number    = {13},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0360-3199},
  doi       = {10.1016/j.ijhydene.2019.01.161},
  pages     = {6978 -- 6990},
  year      = {2019},
  language  = {en}
}
@article{SchmitzSchmitt1984,
  author    = {Schmitz, G{\"u}nter and Schmitt, H. J.},
  title     = {Anisotrope Filmwellenleiter f{\"u}r nichtreziproke optische Bauelemente},
  series = {URSI: Kleinheubacher Tagung am 3.10.83 / Hrsg.: Deutsche Telekom AG},
  journal   = {URSI: Kleinheubacher Tagung am 3.10.83 / Hrsg.: Deutsche Telekom AG},
  address   = {Darmstadt},
  isbn      = {0343-5725},
  pages     = {51},
  year      = {1984},
  language  = {de}
}
@article{GerhardtKonrathStiel2006,
  author    = {Gerhardt, Hans Joachim and Konrath, B. and Stiel, M.},
  title     = {Anmerkungen zur DIN EN 12101-2 {\"u}ber die Pr{\"u}fung von nat{\"u}rlichen Rauch- und W{\"a}rmeabzugsanlagen (NRGW)},
  series = {VFDB-Zeitschrift : Forschung, Technik und Management im Brandschutz. 55 (2006), H. 3},
  journal   = {VFDB-Zeitschrift : Forschung, Technik und Management im Brandschutz. 55 (2006), H. 3},
  isbn      = {0042-1804},
  pages     = {157 -- 158},
  year      = {2006},
  language  = {de}
}
@article{Gerhardt2002,
  author    = {Gerhardt, Hans Joachim},
  title     = {Anmerkungen zur {\"A}hnlichkeit von Modellversuchen bei der Rauchableitung},
  series = {vfdb-Zeitschrift. 51 (2002), H. 2},
  journal   = {vfdb-Zeitschrift. 51 (2002), H. 2},
  isbn      = {0042-1804},
  pages     = {47 -- 49},
  year      = {2002},
  language  = {de}
}
@article{FunkeEschRoosen2022,
  author    = {Funke, Harald and Esch, Thomas and Roosen, Petra},
  title     = {Antriebssystemanpassungen zur Verwendung von LPG als Flugkraftstoff},
  series = {Motortechnische Zeitschrift (MTZ)},
  volume    = {2022},
  journal   = {Motortechnische Zeitschrift (MTZ)},
  number    = {83},
  publisher = {Springer Nature},
  address   = {Basel},
  doi       = {10.1007/s35146-021-0778-2},
  pages     = {58 -- 62},
  year      = {2022},
  abstract  = {Auch in der allgemeinen Luftfahrt w{\"a}re es w{\"u}nschenswert, die bereits vorhandenen Verbrennungsmotoren mit weniger CO₂-tr{\"a}chtigen Kraftstoffen als dem heute weit verbreiteten Avgas 100LL betreiben zu k{\"o}nnen. Es ist anzunehmen, dass im Vergleich die unter Normalbedingungen gasf{\"o}rmigen Kraftstoffe CNG, LPG oder LNG deutlich weniger Emissionen produzieren. Erforderliche Antriebssystemanpassungen wurden im Rahmen eines Forschungsprojekts an der FH Aachen untersucht.},
  language  = {de}
}
@article{SchmitzAltherrHofmannetal.1998,
  author    = {Schmitz, G{\"u}nter and Altherr, M. and Hofmann, O. and Pischinger, M. (u.a.)},
  title     = {Anwendung moderner Simulationstools f{\"u}r die Entwicklung eines elektromagnetischen Ventilaktuators},
  series = {TransMechatronik : Entwicklung und Transfer von Entwicklungssystemen der Mechatronik / Aachener Workshop TransMechatronik 26. Mai 1998, Technologiezentrum am Europaplatz},
  journal   = {TransMechatronik : Entwicklung und Transfer von Entwicklungssystemen der Mechatronik / Aachener Workshop TransMechatronik 26. Mai 1998, Technologiezentrum am Europaplatz},
  publisher = {Heinz-Nixdorf-Inst, Univ.-GH Paderborn},
  address   = {Paderborn},
  isbn      = {3-931466-37-X},
  pages     = {55 -- 74},
  year      = {1998},
  language  = {de}
}
@article{SchmitzSpicherKollmeier1988,
  author    = {Schmitz, G{\"u}nter and Spicher, U. and Kollmeier, H.P.},
  title     = {Application of a New Optical-Fiber Technique for Flame Propagation Diagnostics in IC Engines},
  year      = {1988},
  language  = {en}
}
@article{Gerhardt1995,
  author    = {Gerhardt, Hans Joachim},
  title     = {Arbeitsschutz in Altstoffsortieranlagen - Raumlufttechnische Maßnahmen},
  series = {Abfallwirtschaftsjournal. 7 (1995), H. 7/8},
  journal   = {Abfallwirtschaftsjournal. 7 (1995), H. 7/8},
  isbn      = {0934-6422},
  pages     = {471 -- 473},
  year      = {1995},
  language  = {de}
}
@article{FayyaziSardarThomasetal.2023,
  author    = {Fayyazi, Mojgan and Sardar, Paramjotsingh and Thomas, Sumit Infent and Daghigh, Roonak and Jamali, Ali and Esch, Thomas and Kemper, Hans and Langari, Reza and Khayyam, Hamid},
  title     = {Artificial intelligence/machine learning in energy management systems, control, and optimization of hydrogen fuel cell vehicles},
  volume    = {15},
  number    = {6},
  publisher = {MDPI},
  address   = {Basel},
  doi       = {10.3390/su15065249},
  pages     = {38},
  year      = {2023},
  abstract  = {Environmental emissions, global warming, and energy-related concerns have accelerated the advancements in conventional vehicles that primarily use internal combustion engines. Among the existing technologies, hydrogen fuel cell electric vehicles and fuel cell hybrid electric vehicles may have minimal contributions to greenhouse gas emissions and thus are the prime choices for environmental concerns. However, energy management in fuel cell electric vehicles and fuel cell hybrid electric vehicles is a major challenge. Appropriate control strategies should be used for effective energy management in these vehicles. On the other hand, there has been significant progress in artificial intelligence, machine learning, and designing data-driven intelligent controllers. These techniques have found much attention within the community, and state-of-the-art energy management technologies have been developed based on them. This manuscript reviews the application of machine learning and intelligent controllers for prediction, control, energy management, and vehicle to everything (V2X) in hydrogen fuel cell vehicles. The effectiveness of data-driven control and optimization systems are investigated to evolve, classify, and compare, and future trends and directions for sustainability are discussed.},
  language  = {en}
}
@article{Blome2001,
  author    = {Blome, Hans-Joachim},
  title     = {Aspekte der modernen Kosmologie},
  series = {Mensch, Leben, Schwerkraft, Kosmos : Perspektiven biowissenschaftlicher Weltraumforschung in Deutschland ; Berichtsband einer Klausurtagung vom 20. - 22.10.2000 in Stuttgart-Hohenheim/Birkach / Hinrich Rahmann ... (Hrsg.). [Ausgerichtet von der Deutschen Gesellschaft f{\"u}r Luft- und Raumfahrt medizin]},
  journal   = {Mensch, Leben, Schwerkraft, Kosmos : Perspektiven biowissenschaftlicher Weltraumforschung in Deutschland ; Berichtsband einer Klausurtagung vom 20. - 22.10.2000 in Stuttgart-Hohenheim/Birkach / Hinrich Rahmann ... (Hrsg.). [Ausgerichtet von der Deutschen Gesellschaft f{\"u}r Luft- und Raumfahrt medizin]},
  publisher = {Heimbach},
  address   = {Stuttgart},
  isbn      = {3-935380-03-8},
  pages     = {50 -- 79},
  year      = {2001},
  language  = {de}
}
@article{WilsonBlomeLaFave1996,
  author    = {Wilson, Thomas L and Blome, Hans-Joachim and LaFave, Norman},
  title     = {Astrophysical Cosmology Using a Lunar Ligo},
  series = {Engineering, construction, and operations in space V : proceedings of the Fifth International Conference on Space '96, Albuquerque, New Mexico, June 1-6, 1996 / sponsored by Aerospace Division of the American Society of Civil Engineers ... [et al.]; edite},
  journal   = {Engineering, construction, and operations in space V : proceedings of the Fifth International Conference on Space '96, Albuquerque, New Mexico, June 1-6, 1996 / sponsored by Aerospace Division of the American Society of Civil Engineers ... [et al.]; edite},
  publisher = {The Society},
  address   = {New York},
  isbn      = {0-7844-0177-2},
  pages     = {861 -- 863},
  year      = {1996},
  language  = {en}
}
@article{Wahle2000,
  author    = {Wahle, Michael},
  title     = {Auf sicheren F{\"u}ßen stehen : Entwicklung eines Maschinenlagers mit einem Federkern aus zelligem Polyurethan},
  series = {Der Konstrukteur},
  volume    = {31},
  journal   = {Der Konstrukteur},
  number    = {6},
  isbn      = {0344-4570},
  pages     = {30 -- 32},
  year      = {2000},
  language  = {de}
}
@article{NeuJanserKhatibietal.2016,
  author    = {Neu, Eugen and Janser, Frank and Khatibi, Akbar A. and Orifici, Adrian C.},
  title     = {Automated modal parameter-based anomaly detection under varying wind excitation},
  series = {Structural Health Monitoring},
  volume    = {15},
  journal   = {Structural Health Monitoring},
  number    = {6},
  publisher = {Sage},
  address   = {London},
  issn      = {1475-9217},
  doi       = {10.1177/1475921716665803},
  pages     = {1 -- 20},
  year      = {2016},
  abstract  = {Wind-induced operational variability is one of the major challenges for structural health monitoring of slender engineering structures like aircraft wings or wind turbine blades. Damage sensitive features often show an even bigger sensitivity to operational variability. In this study a composite cantilever was subjected to multiple mass configurations, velocities and angles of attack in a controlled wind tunnel environment. A small-scale impact damage was introduced to the specimen and the structural response measurements were repeated. The proposed damage detection methodology is based on automated operational modal analysis. A novel baseline preparation procedure is described that reduces the amount of user interaction to the provision of a single consistency threshold. The procedure starts with an indeterminate number of operational modal analysis identifications from a large number of datasets and returns a complete baseline matrix of natural frequencies and damping ratios that is suitable for subsequent anomaly detection. Mahalanobis distance-based anomaly detection is then applied to successfully detect the damage under varying severities of operational variability and with various degrees of knowledge about the present operational conditions. The damage detection capabilities of the proposed methodology were found to be excellent under varying velocities and angles of attack. Damage detection was less successful under joint mass and wind variability but could be significantly improved through the provision of the currently encountered operational conditions.},
  language  = {en}
}
@article{SchmitzOligschlaegerEifleretal.1994,
  author    = {Schmitz, G{\"u}nter and Oligschl{\"a}ger, U. and Eifler, G. and Lechner, H.},
  title     = {Automated System for Optimized Calibration of Engine Management Systems},
  year      = {1994},
  language  = {en}
}
@article{LaarmannThomaMischetal.2023,
  author    = {Laarmann, Lukas and Thoma, Andreas and Misch, Philipp and R{\"o}th, Thilo and Braun, Carsten and Watkins, Simon and Fard, Mohammad},
  title     = {Automotive safety approach for future eVTOL vehicles},
  series = {CEAS Aeronautical Journal},
  journal   = {CEAS Aeronautical Journal},
  publisher = {Springer Nature},
  issn      = {1869-5590 (Online)},
  doi       = {10.1007/s13272-023-00655-0},
  pages     = {11 Seiten},
  year      = {2023},
  abstract  = {The eVTOL industry is a rapidly growing mass market expected to start in 2024. eVTOL compete, caused by their predicted missions, with ground-based transportation modes, including mainly passenger cars. Therefore, the automotive and classical aircraft design process is reviewed and compared to highlight advantages for eVTOL development. A special focus is on ergonomic comfort and safety. The need for further investigation of eVTOL's crashworthiness is outlined by, first, specifying the relevance of passive safety via accident statistics and customer perception analysis; second, comparing the current state of regulation and certification; and third, discussing the advantages of integral safety and applying the automotive safety approach for eVTOL development. Integral safety links active and passive safety, while the automotive safety approach means implementing standardized mandatory full-vehicle crash tests for future eVTOL. Subsequently, possible crash impact conditions are analyzed, and three full-vehicle crash load cases are presented.},
  language  = {en}
}
@article{ChristenBarteltKowalski2010,
  author    = {Christen, Marc and Bartelt, Perry and Kowalski, Julia},
  title     = {Back calculation of the In den Arelen avalanche with RAMMS: Interpretation of model results},
  series = {Annals of Glaciology},
  volume    = {51},
  journal   = {Annals of Glaciology},
  number    = {54},
  publisher = {Cambridge University Press},
  address   = {Cambridge},
  isbn      = {1727-5644},
  doi       = {10.3189/172756410791386553},
  pages     = {161 -- 168},
  year      = {2010},
  abstract  = {Two- and three-dimensional avalanche dynamics models are being increasingly used in hazard-mitigation studies. These models can provide improved and more accurate results for hazard mapping than the simple one-dimensional models presently used in practice. However, two- and three-dimensional models generate an extensive amount of output data, making the interpretation of simulation results more difficult. To perform a simulation in three-dimensional terrain, numerical models require a digital elevation model, specification of avalanche release areas (spatial extent and volume), selection of solution methods, finding an adequate calculation resolution and, finally, the choice of friction parameters. In this paper, the importance and difficulty of correctly setting up and analysing the results of a numerical avalanche dynamics simulation is discussed. We apply the two-dimensional simulation program RAMMS to the 1968 extreme avalanche event In den Arelen. We show the effect of model input variations on simulation results and the dangers and complexities in their interpretation.},
  language  = {en}
}
@article{GerhardtKramer1984,
  author    = {Gerhardt, Hans Joachim and Kramer, C.},
  title     = {Belastung von RA bei Windangriff},
  series = {Zentralblatt fuer Industriebau. 30 (1984), H. 3},
  journal   = {Zentralblatt fuer Industriebau. 30 (1984), H. 3},
  isbn      = {0044-4227},
  pages     = {214 -- 217},
  year      = {1984},
  language  = {de}
}
@article{Gerhardt1986,
  author    = {Gerhardt, Hans Joachim},
  title     = {Belastung von Rauchabzugsgeraeten bei Windangriff},
  series = {Sanitaer- und Heizungstechnik. 51 (1986), H. 3},
  journal   = {Sanitaer- und Heizungstechnik. 51 (1986), H. 3},
  isbn      = {0036-4401},
  pages     = {150 -- 152},
  year      = {1986},
  language  = {de}
}
@article{PeekenRosenkranzSchelenz1991,
  author    = {Peeken, Heinz and Rosenkranz, Josef and Schelenz, R.},
  title     = {Ber{\"u}cksichtigung des Einflusses der Gleitlagergeh{\"a}usesteifigkeit auf das dynamische Verhalten von Rotoren},
  series = {Antriebstechnik : Organ der Forschungsvereinigung Antriebstechnik e.V.},
  volume    = {30},
  journal   = {Antriebstechnik : Organ der Forschungsvereinigung Antriebstechnik e.V.},
  number    = {9},
  issn      = {0341-2652},
  pages     = {71 -- 75},
  year      = {1991},
  language  = {de}
}
@article{BlomePriester1991,
  author    = {Blome, Hans-Joachim and Priester, W.},
  title     = {Big Bounce in the very early Universe},
  series = {Astronomy and Astrophysics. 250 (1991), H. 1},
  journal   = {Astronomy and Astrophysics. 250 (1991), H. 1},
  isbn      = {0004-6361},
  pages     = {43 -- 49},
  year      = {1991},
  language  = {en}
}
@article{ThomessenThomaBraun2023,
  author    = {Thomessen, Karolin and Thoma, Andreas and Braun, Carsten},
  title     = {Bio-inspired altitude changing extension to the 3DVFH* local obstacle avoidance algorithm},
  series = {CEAS Aeronautical Journal},
  journal   = {CEAS Aeronautical Journal},
  publisher = {Springer},
  address   = {Wien},
  issn      = {1869-5590 (Online)},
  doi       = {10.1007/s13272-023-00691-w},
  pages     = {11 Seiten},
  year      = {2023},
  abstract  = {Obstacle avoidance is critical for unmanned aerial vehicles (UAVs) operating autonomously. Obstacle avoidance algorithms either rely on global environment data or local sensor data. Local path planners react to unforeseen objects and plan purely on local sensor information. Similarly, animals need to find feasible paths based on local information about their surroundings. Therefore, their behavior is a valuable source of inspiration for path planning. Bumblebees tend to fly vertically over far-away obstacles and horizontally around close ones, implying two zones for different flight strategies depending on the distance to obstacles. This work enhances the local path planner 3DVFH* with this bio-inspired strategy. The algorithm alters the goal-driven function of the 3DVFH* to climb-preferring if obstacles are far away. Prior experiments with bumblebees led to two definitions of flight zone limits depending on the distance to obstacles, leading to two algorithm variants. Both variants reduce the probability of not reaching the goal of a 3DVFH* implementation in Matlab/Simulink. The best variant, 3DVFH*b-b, reduces this probability from 70.7 to 18.6\% in city-like worlds using a strong vertical evasion strategy. Energy consumption is higher, and flight paths are longer compared to the algorithm version with pronounced horizontal evasion tendency. A parameter study analyzes the effect of different weighting factors in the cost function. The best parameter combination shows a failure probability of 6.9\% in city-like worlds and reduces energy consumption by 28\%. Our findings demonstrate the potential of bio-inspired approaches for improving the performance of local path planning algorithms for UAV.},
  language  = {en}
}