@article{PichlerGeorgeSeileretal.2009,
  author    = {Pichler, A. and George, A. and Seiler, F. and Srulijes, J. and Havermann, Marc},
  title     = {Doppler Picture Velocimetry (DPV) applied to hypersonics},
  series = {Shock Waves [Elektronische Ressource] : 26th International Symposium on Shock Waves, Volume 1 / edited by Klaus Hannemann, Friedrich Seiler},
  journal   = {Shock Waves [Elektronische Ressource] : 26th International Symposium on Shock Waves, Volume 1 / edited by Klaus Hannemann, Friedrich Seiler},
  publisher = {Springer},
  address   = {Berlin},
  isbn      = {978-3-540-85168-4},
  pages     = {503 -- 508},
  year      = {2009},
  language  = {en}
}
@article{FischerKowalskiPudasainietal.2009,
  author    = {Fischer, Jan-Thomas and Kowalski, Julia and Pudasaini, Shiva P. and Miller, S. A.},
  title     = {Dynamic Avalanche Modeling in Natural Terrain},
  series = {International Snow Science Workshop, Davos 2009, Proceedings ; Proc. ISSW 2009},
  journal   = {International Snow Science Workshop, Davos 2009, Proceedings ; Proc. ISSW 2009},
  pages     = {448 -- 452},
  year      = {2009},
  abstract  = {The powerful avalanche simulation toolbox RAMMS (Rapid Mass Movements) is based on a depth-averaged hydrodynamic system of equations with a Voellmy-Salm friction relation. The two empirical friction parameters μ and � correspond to a dry Coulomb friction and a viscous resistance, respectively. Although μ and � lack a proper physical explanation, 60 years of acquired avalanche data in the Swiss Alps made a systematic calibration possible. RAMMS can therefore successfully model avalanche flow depth, velocities, impact pressure and run out distances. Pudasaini and Hutter (2003) have proposed extended, rigorously derived model equations that account for local curvature and twist. A coordinate transformation into a reference system, applied to the actual mountain topography of the natural avalanche path, is performed. The local curvature and the twist of the avalanche path induce an additional term in the overburden pressure. This leads to a modification of the Coulomb friction, the free-surface pressure gradient, the pressure induced by the channel, and the gravity components along and normal to the curved and twisted reference surface. This eventually guides the flow dynamics and deposits of avalanches. In the present study, we investigate the influence of curvature on avalanche flow in real mountain terrain. Simulations of real avalanche paths are performed and compared for the different models approaches. An algorithm to calculate curvature in real terrain is introduced in RAMMS. This leads to a curvature dependent friction relation in an extended version of the Voellmy-Salm model equations. Our analysis provides yet another step in interpreting the physical meaning and significance of the friction parameters used in the RAMMS computational environment.},
  language  = {en}
}
@article{Havermann2005,
  author    = {Havermann, Marc},
  title     = {Effects of the shock tube open-end shape on vortex loops released from it / Kainuma, M. ; Havermann, M. ; Sun, M. ; Takayama, K.},
  series = {Shock Waves : Proceedings of the 24th International Symposium on Shock Waves Beijing, China July 11-16, 2004 / edited by Z. Jiang},
  journal   = {Shock Waves : Proceedings of the 24th International Symposium on Shock Waves Beijing, China July 11-16, 2004 / edited by Z. Jiang},
  publisher = {Springer},
  address   = {Berlin},
  isbn      = {978-3-540-22497-6},
  pages     = {505 -- 510},
  year      = {2005},
  language  = {en}
}
@article{DahlSuttrop1998,
  author    = {Dahl, G{\"u}nter and Suttrop, F.},
  title     = {Engine control and low-NO(x) combustion for hydrogen fuelled aircraft gas turbines},
  series = {International Journal of Hydrogen Energy. 23 (1998), H. 8},
  journal   = {International Journal of Hydrogen Energy. 23 (1998), H. 8},
  isbn      = {0360-3199},
  pages     = {695 -- 704},
  year      = {1998},
  language  = {en}
}
@article{HavermannSeilerGeorgeetal.2002,
  author    = {Havermann, Marc and Seiler, F. and George, A. and Leopold, F.},
  title     = {Enhanced Doppler Picture Velocimetry (DPV) for Planar Velocity Measurements in High-Speed Shock Tunnel Flow / Seiler, F. ; George, A. ; Leopold, F. ; Havermann, M. ; Srulijes, J.},
  series = {10th International Symposium on Flow Visualization : Kyōto, Japan, August 26 - 29, 2002 / sponsored by International Flow Visualization Society . [Chairman:] Toshio Kobayashi},
  journal   = {10th International Symposium on Flow Visualization : Kyōto, Japan, August 26 - 29, 2002 / sponsored by International Flow Visualization Society . [Chairman:] Toshio Kobayashi},
  publisher = {Visualization Society of Japan},
  address   = {Kyoto},
  isbn      = {4906497829},
  year      = {2002},
  language  = {en}
}
@article{TekinAshikagaHorikawaetal.2018,
  author    = {Tekin, Nurettin and Ashikaga, Mitsugu and Horikawa, Atsushi and Funke, Harald},
  title     = {Enhancement of fuel flexibility of industrial gas turbines by development of innovative hydrogen combustion systems},
  series = {Gas for energy},
  journal   = {Gas for energy},
  number    = {2},
  publisher = {Vulkan-Verlag},
  address   = {Essen},
  pages     = {4},
  year      = {2018},
  abstract  = {For fuel flexibility enhancement hydrogen represents a possible alternative gas turbine fuel within future low emission power generation, in case of hydrogen production by the use of renewable energy sources such as wind energy or biomass. Kawasaki Heavy Industries, Ltd. (KHI) has research and development projects for future hydrogen society; production of hydrogen gas, refinement and liquefaction for transportation and storage, and utilization with gas turbine / gas engine for the generation of electricity. In the development of hydrogen gas turbines, a key technology is the stable and low NOx hydrogen combustion, especially Dry Low Emission (DLE) or Dry Low NOx (DLN) hydrogen combustion. Due to the large difference in the physical properties of hydrogen compared to other fuels such as natural gas, well established gas turbine combustion systems cannot be directly applied for DLE hydrogen combustion. Thus, the development of DLE hydrogen combustion technologies is an essential and challenging task for the future of hydrogen fueled gas turbines. The DLE Micro-Mix combustion principle for hydrogen fuel has been in development for many years to significantly reduce NOx emissions. This combustion principle is based on cross-flow mixing of air and gaseous hydrogen which reacts in multiple miniaturized "diffusion-type" flames. The major advantages of this combustion principle are the inherent safety against flashback and the low NOx-emissions due to a very short residence time of the reactants in the flame region of the micro-flames.},
  language  = {en}
}
@article{DachwaldCarnelliVasile2006,
  author    = {Dachwald, Bernd and Carnelli, I. and Vasile, M.},
  title     = {Evolutionary Neurocontrol as a Novel Method for Low-Thrust Gravity Assist Trajectory Optimization / I. Carnelli ; B. Dachwald ; M. Vasile},
  series = {Proceedings of the Twenty-Fifth International Symposium on Space Technology and Science (Selected papers) : Kanazawa, [June 4 through June 11, 2006, at Kanazawa-shi Kanko Kaikan in Kanazawa city] / [Japan Society for Aeronautical and Space Sciences. Kohtaro Matsumoto [ed.-in-chief]},
  journal   = {Proceedings of the Twenty-Fifth International Symposium on Space Technology and Science (Selected papers) : Kanazawa, [June 4 through June 11, 2006, at Kanazawa-shi Kanko Kaikan in Kanazawa city] / [Japan Society for Aeronautical and Space Sciences. Kohtaro Matsumoto [ed.-in-chief]},
  publisher = {JSASS},
  address   = {Tokyo},
  isbn      = {4-99005-002-9},
  pages     = {569 -- 574},
  year      = {2006},
  language  = {en}
}
@article{DachwaldCarnelliVasile2009,
  author    = {Dachwald, Bernd and Carnelli, Ian and Vasile, Massimiliano},
  title     = {Evolutionary Neurocontrol: A Novel Method for Low-Thrust Gravity-Assist Trajectory Optimization / Carnelli, Ian ; Dachwald, Bernd ; Vasile, Massimiliano},
  series = {Journal of guidance control and dynamics. 32 (2009), H. 2},
  journal   = {Journal of guidance control and dynamics. 32 (2009), H. 2},
  publisher = {AIAA},
  address   = {Reston, Va.},
  isbn      = {0731-5090},
  pages     = {616 -- 625},
  year      = {2009},
  language  = {en}
}
@article{Dachwald2004,
  author    = {Dachwald, Bernd},
  title     = {Evolutionary Neurocontrol: A Smart Method for Global Optimization of Low-Thrust Trajectories},
  series = {22nd AIAA Applied Aerodynamics Conference and Exhibit - AIAA/AAS Astrodynamics Specialist Conference and Exhibit - AIAA Guidance, Navigation, and Control Conference and Exhibit - AIAA Modeling and Simulation Technologies Conference and Exhibit - AIAA Atmospheric Flight Mechanics Conference and Exhibit : 16 - 19 August 2004, Providence, Rhode Island / American Institute of Aeronautics and Astronautics. - (AIAA meeting papers on disc ; 2004,14-15)},
  journal   = {22nd AIAA Applied Aerodynamics Conference and Exhibit - AIAA/AAS Astrodynamics Specialist Conference and Exhibit - AIAA Guidance, Navigation, and Control Conference and Exhibit - AIAA Modeling and Simulation Technologies Conference and Exhibit - AIAA Atmospheric Flight Mechanics Conference and Exhibit : 16 - 19 August 2004, Providence, Rhode Island / American Institute of Aeronautics and Astronautics. - (AIAA meeting papers on disc ; 2004,14-15)},
  publisher = {American Inst. of Aeronautics and Astronautics},
  address   = {Reston, Va.},
  pages     = {2 CD-ROMs},
  year      = {2004},
  language  = {en}
}
@article{OlaruKowalskiSethietal.2012,
  author    = {Olaru, Alexandra Maria and Kowalski, Julia and Sethi, Vaishali and Bl{\"u}mich, Bernhard},
  title     = {Exchange relaxometry of flow at small P{\´e}clet numbers in a glass bead pack},
  series = {Journal of Magnetic Resonance (JMR)},
  volume    = {220},
  journal   = {Journal of Magnetic Resonance (JMR)},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1096-0856},
  doi       = {10.1016/j.jmr.2012.04.015},
  pages     = {32 -- 44},
  year      = {2012},
  abstract  = {In this paper we consider low P{\´e}clet number flow in bead packs. A series of relaxation exchange experiments has been conducted and evaluated by ILT analysis. In the resulting correlation maps, we observed a collapse of the signal and a translation towards smaller relaxation times with increasing flow rates, as well as a signal tilt with respect to the diagonal. In the discussion of the phenomena we present a mathematical theory for relaxation exchange experiments that considers both diffusive and advective transport. We perform simulations based on this theory and discuss them with respect to the conducted experiments.},
  language  = {en}
}
@article{HajAyedKustererFunkeetal.2015,
  author    = {Haj Ayed, A. and Kusterer, K. and Funke, Harald and Keinz, Jan and Striegan, Constantin and Bohn, D.},
  title     = {Experimental and numerical investigations of the dry-low-NOx hydrogen micromix combustion chamber of an industrial gas turbine},
  series = {Propulsion and power research},
  volume    = {Vol. 4},
  journal   = {Propulsion and power research},
  number    = {Iss. 3},
  issn      = {2212-540X},
  doi       = {10.1016/j.jppr.2015.07.005},
  pages     = {123 -- 131},
  year      = {2015},
  language  = {en}
}
@article{FunkeDickhoffKeinzetal.2014,
  author    = {Funke, Harald and Dickhoff, J. and Keinz, Jan and Anis, H. A. and Parente, A. and Hendrick, P.},
  title     = {Experimental and numerical study of the micromix combustion principle applied for hydrogen and hydrogen-rich syngas as fuel with increased energy density for industrial gas turbine applications},
  series = {Energy procedia},
  journal   = {Energy procedia},
  number    = {61},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1876-6102 (E-Journal)},
  doi       = {10.1016/j.egypro.2014.12.201},
  pages     = {1736 -- 1739},
  year      = {2014},
  abstract  = {The Dry Low NOx (DLN) Micromix combustion principle with increased energy density is adapted for the industrial gas turbine APU GTCP 36-300 using hydrogen and hydrogen-rich syngas with a composition of 90\%-Vol. hydrogen (H₂) and 10\%-Vol. carbon-monoxide (CO). Experimental and numerical studies of several combustor geometries for hydrogen and syngas show the successful advance of the DLN Micromix combustion from pure hydrogen to hydrogen-rich syngas. The impact of the different fuel properties on the combustion principle and aerodynamic flame stabilization design laws, flow field, flame structure and emission characteristics is investigated by numerical analysis using a hybrid Eddy Break Up combustion model and validated against experimental results.},
  language  = {en}
}
@article{FunkeKeinzKustereretal.2016,
  author    = {Funke, Harald and Keinz, Jan and Kusterer, Karsten and Ayed, Anis Haj and Kazari, Masahide and Kitajima, Junichi and Horikawa, Atsushi and Okada, Kunio},
  title     = {Experimental and Numerical Study on Optimizing the Dry Low NOₓ Micromix Hydrogen Combustion Principle for Industrial Gas Turbine Applications},
  series = {Journal of Thermal Science and Engineering Applications},
  volume    = {9},
  journal   = {Journal of Thermal Science and Engineering Applications},
  number    = {2},
  publisher = {ASME},
  address   = {New York, NY},
  issn      = {1948-5093},
  doi       = {10.1115/1.4034849},
  pages     = {021001 -- 021001-10},
  year      = {2016},
  abstract  = {Combined with the use of renewable energy sources for its production, hydrogen represents a possible alternative gas turbine fuel for future low-emission power generation. Due to the difference in the physical properties of hydrogen compared to other fuels such as natural gas, well-established gas turbine combustion systems cannot be directly applied to dry low NOₓ (DLN) hydrogen combustion. The DLN micromix combustion of hydrogen has been under development for many years, since it has the promise to significantly reduce NOₓ emissions. This combustion principle for air-breathing engines is based on crossflow mixing of air and gaseous hydrogen. Air and hydrogen react in multiple miniaturized diffusion-type flames with an inherent safety against flashback and with low NOₓ emissions due to a very short residence time of the reactants in the flame region. The paper presents an advanced DLN micromix hydrogen application. The experimental and numerical study shows a combustor configuration with a significantly reduced number of enlarged fuel injectors with high-thermal power output at constant energy density. Larger fuel injectors reduce manufacturing costs, are more robust and less sensitive to fuel contamination and blockage in industrial environments. The experimental and numerical results confirm the successful application of high-energy injectors, while the DLN micromix characteristics of the design point, under part-load conditions, and under off-design operation are maintained. Atmospheric test rig data on NOₓ emissions, optical flame-structure, and combustor material temperatures are compared to numerical simulations and show good agreement. The impact of the applied scaling and design laws on the miniaturized micromix flamelets is particularly investigated numerically for the resulting flow field, the flame-structure, and NOₓ formation.},
  language  = {en}
}
@article{FunkeBoernerKrebsetal.2011,
  author    = {Funke, Harald and B{\"o}rner, Sebastian and Krebs, W. and Wolf, E.},
  title     = {Experimental Characterization of Low NOx Micromix Prototype Combustors for Industrial Gas Turbine Applications},
  series = {ASME Turbo Expo 2011 ; Vancouver, Canada, June 6-10, 2011},
  journal   = {ASME Turbo Expo 2011 ; Vancouver, Canada, June 6-10, 2011},
  year      = {2011},
  language  = {en}
}
@article{BohnFunke2003,
  author    = {Bohn, Dieter and Funke, Harald},
  title     = {Experimental investigations into the nonuniform flow in a 4-stage turbine with special focus on the flow equalization in the first turbine stage},
  series = {ASME TURBO EXPO, Proceedings of the ASME Turbo Expo, 2003},
  journal   = {ASME TURBO EXPO, Proceedings of the ASME Turbo Expo, 2003},
  isbn      = {0-7918-3689-4},
  pages     = {281 -- 289},
  year      = {2003},
  language  = {en}
}
@article{ReckerBosschaertsWagemakersetal.2010,
  author    = {Recker, Elmar and Bosschaerts, Walter and Wagemakers, Rolf and Hendrick, Patrick and Funke, Harald and B{\"o}rner, Sebastian},
  title     = {Experimental study of a round jet in cross-flow at low momentum ratio},
  series = {15th International Symposium on Applications of Laser Techniques to Fluid Mechanics Lisbon, Portugal, 05-08 July, 2010 - 1},
  journal   = {15th International Symposium on Applications of Laser Techniques to Fluid Mechanics Lisbon, Portugal, 05-08 July, 2010 - 1},
  pages     = {1 -- 13},
  year      = {2010},
  language  = {en}
}
@article{HavermannSalveTinetal.1994,
  author    = {Havermann, Marc and Salve, M. de and Tin, G. del and Panella, B.},
  title     = {Experimental Study of the Temperature Field along a Density Lock / Salve, M. de ; Tin, G. del ; Panella, B. ; Sansoldo, D. ; Havermann, M.},
  series = {Proceedings : International Conference on New Trends in Nuclear System Thermohydraulics, May 30th - June 2nd, 1994, Pisa / organized by Dipartimento di Costruzioni Meccaniche e Nucleari ... . Ed. by Francesco Oriolo},
  journal   = {Proceedings : International Conference on New Trends in Nuclear System Thermohydraulics, May 30th - June 2nd, 1994, Pisa / organized by Dipartimento di Costruzioni Meccaniche e Nucleari ... . Ed. by Francesco Oriolo},
  publisher = {-},
  address   = {Pisa},
  pages     = {623 -- 630},
  year      = {1994},
  language  = {en}
}
@article{McArdellBarteltKowalski2007,
  author    = {McArdell, Brian W. and Bartelt, Perry and Kowalski, Julia},
  title     = {Field observations of basal forces and fluid pore pressure in a debris flow},
  series = {Geophysical Research Letters (GRL)},
  volume    = {34},
  journal   = {Geophysical Research Letters (GRL)},
  number    = {7},
  isbn      = {0094-8276},
  year      = {2007},
  abstract  = {Using results from an 8 m2 instrumented force plate we describe field measurements of normal and shear stresses, and fluid pore pressure for a debris flow. The flow depth increased from 0.1 to 1 m within the first 12 s of flow front arrival, remained relatively constant until 100 s, and then gradually decreased to 0.5 m by 600 s. Normal and shear stresses and pore fluid pressure varied in-phase with the flow depth. Calculated bulk densities are ρb = 2000-2250 kg m-3 for the bulk flow and ρf = 1600-1750 kg m-3 for the fluid phase. The ratio of effective normal stress to shear stress yields a Coulomb basal friction angle of ϕ = 26° at the flow front. We did not find a strong correlation between the degree of agitation in the flow, estimated using the signal from a geophone on the force plate, and an assumed dynamic pore fluid pressure. Our data support the idea that excess pore-fluid pressures are long lived in debris flows and therefore contribute to their unusual mobility.},
  language  = {en}
}
@article{BaaderBoxbergChenetal.2023,
  author    = {Baader, Fabian and Boxberg, Marc S. and Chen, Qian and F{\"o}rstner, Roger and Kowalski, Julia and Dachwald, Bernd},
  title     = {Field-test performance of an ice-melting probe in a terrestrial analogue environment},
  series = {Icarus},
  journal   = {Icarus},
  number    = {409},
  publisher = {Elsevier},
  address   = {Amsterdam},
  doi       = {10.1016/j.icarus.2023.115852},
  pages     = {Artikel 115852},
  year      = {2023},
  abstract  = {Melting probes are a proven tool for the exploration of thick ice layers and clean sampling of subglacial water on Earth. Their compact size and ease of operation also make them a key technology for the future exploration of icy moons in our Solar System, most prominently Europa and Enceladus. For both mission planning and hardware engineering, metrics such as efficiency and expected performance in terms of achievable speed, power requirements, and necessary heating power have to be known. Theoretical studies aim at describing thermal losses on the one hand, while laboratory experiments and field tests allow an empirical investigation of the true performance on the other hand. To investigate the practical value of a performance model for the operational performance in extraterrestrial environments, we first contrast measured data from terrestrial field tests on temperate and polythermal glaciers with results from basic heat loss models and a melt trajectory model. For this purpose, we propose conventions for the determination of two different efficiencies that can be applied to both measured data and models. One definition of efficiency is related to the melting head only, while the other definition considers the melting probe as a whole. We also present methods to combine several sources of heat loss for probes with a circular cross-section, and to translate the geometry of probes with a non-circular cross-section to analyse them in the same way. The models were selected in a way that minimizes the need to make assumptions about unknown parameters of the probe or the ice environment. The results indicate that currently used models do not yet reliably reproduce the performance of a probe under realistic conditions. Melting velocities and efficiencies are constantly overestimated by 15 to 50 \% in the models, but qualitatively agree with the field test data. Hence, losses are observed, that are not yet covered and quantified by the available loss models. We find that the deviation increases with decreasing ice temperature. We suspect that this mismatch is mainly due to the too restrictive idealization of the probe model and the fact that the probe was not operated in an efficiency-optimized manner during the field tests. With respect to space mission engineering, we find that performance and efficiency models must be used with caution in unknown ice environments, as various ice parameters have a significant effect on the melting process. Some of these are difficult to estimate from afar.},
  language  = {en}
}
@article{FunkeBeckmann2022,
  author    = {Funke, Harald and Beckmann, Nils},
  title     = {Flexible fuel operation of a Dry-Low-NOx Micromix Combustor with Variable Hydrogen Methane Mixture},
  series = {International Journal of Gas Turbine, Propulsion and Power Systems},
  volume    = {13},
  journal   = {International Journal of Gas Turbine, Propulsion and Power Systems},
  number    = {2},
  issn      = {1882-5079},
  pages     = {1 -- 7},
  year      = {2022},
  abstract  = {The role of hydrogen (H2) as a carbon-free energy carrier is discussed since decades for reducing greenhouse gas emissions. As bridge technology towards a hydrogen-based energy supply, fuel mixtures of natural gas or methane (CH4) and hydrogen are possible. The paper presents the first test results of a low-emission Micromix combustor designed for flexible-fuel operation with variable H2/CH4 mixtures. The numerical and experimental approach for considering variable fuel mixtures instead of recently investigated pure hydrogen is described. In the experimental studies, a first generation FuelFlex Micromix combustor geometry is tested at atmospheric pressure at gas turbine operating conditions corresponding to part- and full-load. The H2/CH4 fuel mixture composition is varied between 57 and 100 vol.\% hydrogen content. Despite the challenges flexible-fuel operation poses onto the design of a combustion system, the evaluated FuelFlex Micromix prototype shows a significant low NOx performance},
  language  = {en}
}
@article{DachwaldSchmidtSeboldtetal.2003,
  author    = {Dachwald, Bernd and Schmidt, Tanja D. and Seboldt, Wolfgang and Auweter-Kurtz,},
  title     = {Flight Opportunities from Mars to Earth for Piloted Missions Using Continuous Thrust Propulsion / Schmidt, Tanja D. ; Dachwald, Bernd ; Seboldt, Wolfgang ; Auweter-Kurtz, Monika},
  publisher = {-},
  pages     = {1 -- 9},
  year      = {2003},
  language  = {en}
}
@article{ScholzLeyDachwaldetal.2010,
  author    = {Scholz, A. and Ley, Wilfried and Dachwald, Bernd and Miau, J. J. and Juang, J. C.},
  title     = {Flight results of the COMPASS-1 picosatellite mission},
  series = {Acta Astronautica. 67 (2010), H. 9-10},
  journal   = {Acta Astronautica. 67 (2010), H. 9-10},
  isbn      = {0094-5765},
  pages     = {1289 -- 1298},
  year      = {2010},
  language  = {en}
}
@article{GerhardtKramerJanssen1985,
  author    = {Gerhardt, Hans Joachim and Kramer, C. and Janssen, L.-J.},
  title     = {Flow studies of an open jet wind tunnel and comparison with closed and slotted walls},
  pages     = {7 -- 28},
  year      = {1985},
  language  = {en}
}
@article{HammerQuitterMayntzetal.2023,
  author    = {Hammer, Thorben and Quitter, Julius and Mayntz, Joscha and Bauschat, J.-Michael and Dahmann, Peter and G{\"o}tten, Falk and Hille, Sebastian and Stumpf, Eike},
  title     = {Free fall drag estimation of small-scale multirotor unmanned aircraft systems using computational fluid dynamics and wind tunnel experiments},
  series = {CEAS Aeronautical Journal},
  journal   = {CEAS Aeronautical Journal},
  publisher = {Springer},
  address   = {Wien},
  issn      = {1869-5590 (Online)},
  doi       = {10.1007/s13272-023-00702-w},
  pages     = {14 Seiten},
  year      = {2023},
  abstract  = {New European Union (EU) regulations for UAS operations require an operational risk analysis, which includes an estimation of the potential danger of the UAS crashing. A key parameter for the potential ground risk is the kinetic impact energy of the UAS. The kinetic energy depends on the impact velocity of the UAS and, therefore, on the aerodynamic drag and the weight during free fall. Hence, estimating the impact energy of a UAS requires an accurate drag estimation of the UAS in that state. The paper at hand presents the aerodynamic drag estimation of small-scale multirotor UAS. Multirotor UAS of various sizes and configurations were analysed with a fully unsteady Reynolds-averaged Navier-Stokes approach. These simulations included different velocities and various fuselage pitch angles of the UAS. The results were compared against force measurements performed in a subsonic wind tunnel and provided good consistency. Furthermore, the influence of the UAS`s fuselage pitch angle as well as the influence of fixed and free spinning propellers on the aerodynamic drag was analysed. Free spinning propellers may increase the drag by up to 110\%, depending on the fuselage pitch angle. Increasing the fuselage pitch angle of the UAS lowers the drag by 40\% up to 85\%, depending on the UAS. The data presented in this paper allow for increased accuracy of ground risk assessments.},
  language  = {en}
}
@article{GoettenFingerHavermannetal.2021,
  author    = {G{\"o}tten, Falk and Finger, Felix and Havermann, Marc and Braun, Carsten and Marino, M. and Bil, C.},
  title     = {Full configuration drag estimation of short-to-medium range fixed-wing UAVs and its impact on initial sizing optimization},
  series = {CEAS Aeronautical Journal},
  volume    = {12},
  journal   = {CEAS Aeronautical Journal},
  publisher = {Springer},
  address   = {Berlin},
  issn      = {1869-5590 (Online)},
  doi       = {10.1007/s13272-021-00522-w},
  pages     = {589 -- 603},
  year      = {2021},
  abstract  = {The paper presents the derivation of a new equivalent skin friction coefficient for estimating the parasitic drag of short-to-medium range fixed-wing unmanned aircraft. The new coefficient is derived from an aerodynamic analysis of ten different unmanned aircraft used for surveillance, reconnaissance, and search and rescue missions. The aircraft is simulated using a validated unsteady Reynolds-averaged Navier Stokes approach. The UAV's parasitic drag is significantly influenced by the presence of miscellaneous components like fixed landing gears or electro-optical sensor turrets. These components are responsible for almost half of an unmanned aircraft's total parasitic drag. The new equivalent skin friction coefficient accounts for these effects and is significantly higher compared to other aircraft categories. It is used to initially size an unmanned aircraft for a typical reconnaissance mission. The improved parasitic drag estimation yields a much heavier unmanned aircraft when compared to the sizing results using available drag data of manned aircraft.},
  language  = {en}
}
@article{NeuJanserKhatibietal.2017,
  author    = {Neu, Eugen and Janser, Frank and Khatibi, Akbar A. and Orifici, Adrian C.},
  title     = {Fully Automated Operational Modal Analysis using multi-stage clustering},
  series = {Mechanical Systems and Signal Processing},
  volume    = {Vol. 84, Part A},
  journal   = {Mechanical Systems and Signal Processing},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0888-3270},
  doi       = {10.1016/j.ymssp.2016.07.031},
  pages     = {308 -- 323},
  year      = {2017},
  language  = {en}
}
@article{DachwaldTuryshevDittusetal.2005,
  author    = {Dachwald, Bernd and Turyshev, Slava G. and Dittus, H. and Shao, M. [u.a.]},
  title     = {Fundamental Physics with the Laser Astrometric Test Of Relativity / S.G. Turyshev ; H. Dittus ; M. Shao ... B.Dachwald ...},
  series = {Proceedings of the 39th ESLAB Symposium "Trends in Space Science and Cosmic Vision 2020" : 19 - 21 April 2005, ESTEC, Noordwijk, the Netherlands / European Space Agency. [Comp. by: F. Favata ...] . - (ESA SP ; 588)},
  journal   = {Proceedings of the 39th ESLAB Symposium "Trends in Space Science and Cosmic Vision 2020" : 19 - 21 April 2005, ESTEC, Noordwijk, the Netherlands / European Space Agency. [Comp. by: F. Favata ...] . - (ESA SP ; 588)},
  publisher = {ESA Publ. Div.},
  address   = {Noordwijk},
  isbn      = {9290928999},
  pages     = {8 -- 11},
  year      = {2005},
  language  = {en}
}
@article{DachwaldMacDonaldMcInnes2007,
  author    = {Dachwald, Bernd and MacDonald, Malcolm and McInnes, Colin R.},
  title     = {Heliocentric Solar Sail Orbit Transfers with Locally Optimal Control Laws / Malcolm Macdonald ; Colin McInnes ; Bernd Dachwald},
  series = {Journal of Spacecraft and Rockets. 44 (2007), H. 1},
  journal   = {Journal of Spacecraft and Rockets. 44 (2007), H. 1},
  isbn      = {0022-4650},
  pages     = {273 -- 276},
  year      = {2007},
  language  = {en}
}
@article{LeipoldFichtnerHeberetal.2006,
  author    = {Leipold, M. and Fichtner, H. and Heber, B. and Groepper, P. and Lascar, S. and Burger, F. and Eiden, M. and Niederstadt, T. and Sickinger, C. and Herbeck, L. and Dachwald, Bernd and Seboldt, W.},
  title     = {Heliopause Explorer - A Sailcraft Mission to the Outer Boundaries of the Solar System},
  series = {Acta Astronautica. 59 (2006), H. 8-11},
  journal   = {Acta Astronautica. 59 (2006), H. 8-11},
  isbn      = {0094-5765},
  pages     = {786 -- 796},
  year      = {2006},
  language  = {en}
}
@article{DachwaldLeipoldFichtner2003,
  author    = {Dachwald, Bernd and Leipold, M. and Fichtner, H.},
  title     = {Heliopause Explorer - A Sailcraft Mission to the Outer Boundaries of the Solar System / M. Leipold ; H. Fichtner ; B. Heber ... B. Dachwald ...},
  series = {Proceedings of the Fifth IAA International Conference on Low Cost Planetary Missions : 24 - 26 September 2003, ESTEC, Noordwijk, the Netherlands / [comp. by R. A. Harris]},
  journal   = {Proceedings of the Fifth IAA International Conference on Low Cost Planetary Missions : 24 - 26 September 2003, ESTEC, Noordwijk, the Netherlands / [comp. by R. A. Harris]},
  publisher = {ESA},
  address   = {Noordwijk},
  isbn      = {92-9092-853-0},
  pages     = {367 -- 375},
  year      = {2003},
  language  = {en}
}
@article{WittmannKellWinkleretal.1998,
  author    = {Wittmann, Klaus and Kell, G. and Winkler, F. and G{\"u}nther, M. (u.a.)},
  title     = {High resolution temperature measurement technique for materials sciences experiments in space},
  series = {Acta Astronautica. 43 (1998), H. 7-8},
  journal   = {Acta Astronautica. 43 (1998), H. 7-8},
  isbn      = {0094-5765},
  pages     = {385 -- 395},
  year      = {1998},
  language  = {en}
}
@article{SchirraWatmuffBauschat2014,
  author    = {Schirra, Julian and Watmuff, Jonathan and Bauschat, J.-Michael},
  title     = {Highly non-planar lifting systems: a relative assessment of existing potential-methodologies to accurately estimate the induced drag},
  series = {32nd AIAA Applied Aerodynamics Conference 2014 : June, 16-20 2014, Atlanta, Ga.},
  journal   = {32nd AIAA Applied Aerodynamics Conference 2014 : June, 16-20 2014, Atlanta, Ga.},
  organization    = {American Institute of Aeronautics and Astronautics},
  isbn      = {978-1-62410-288-2},
  doi       = {10.2514/6.2014-2988},
  pages     = {Publ. online},
  year      = {2014},
  language  = {en}
}
@article{BohndickBosseJaenschetal.2021,
  author    = {Bohndick, Carla and Bosse, Elke and J{\"a}nsch, Vanessa K. and Barnat, Miriam},
  title     = {How different diversity factors affect the perception of first-year requirements in higher education},
  series = {Frontline Learning Research},
  volume    = {9},
  journal   = {Frontline Learning Research},
  number    = {2},
  publisher = {EARLI},
  issn      = {2295-3159},
  doi       = {10.14786/flr.v9i2.667},
  pages     = {78 -- 95},
  year      = {2021},
  abstract  = {In the light of growing university entry rates, higher education institutions not only serve larger numbers of students, but also seek to meet first-year students' ever more diverse needs. Yet to inform universities how to support the transition to higher education, research only offers limited insights. Current studies tend to either focus on the individual factors that affect student success or they highlight students' social background and their educational biography in order to examine the achievement of selected, non-traditional groups of students. Both lines of research appear to lack integration and often fail to take organisational diversity into account, such as different types of higher education institutions or degree programmes. For a more comprehensive understanding of student diversity, the present study includes individual, social and organisational factors. To gain insights into their role for the transition to higher education, we examine how the different factors affect the students' perception of the formal and informal requirements of the first year as more or less difficult to cope with. As the perceived requirements result from both the characteristics of the students and the institutional context, they allow to investigate transition at the interface of the micro and the meso level of higher education. Latent profile analyses revealed that there are no profiles with complex patterns of perception of the first-year requirements, but the identified groups rather differ in the overall level of perceived challenges. Moreover, SEM indicates that the differences in the perception largely depend on the individual factors self-efficacy and volition.},
  language  = {en}
}
@article{DickhoffHorikawaFunke2021,
  author    = {Dickhoff, Jens and Horikawa, Atsushi and Funke, Harald},
  title     = {Hydrogen Combustion - new DLE Combustor Addresses NOx Emissions and Flashback},
  series = {Turbomachinery international : the global journal of energy equipment},
  volume    = {62},
  journal   = {Turbomachinery international : the global journal of energy equipment},
  number    = {4},
  publisher = {MJH Life Sciences},
  address   = {Cranbury},
  issn      = {2767-2328},
  pages     = {26 -- 27},
  year      = {2021},
  language  = {en}
}
@article{BlomeKundt1987,
  author    = {Blome, Hans-Joachim and Kundt, W.},
  title     = {Hypersonic Jets from Young Stars in Molecular Clouds},
  series = {Circumstellar matter : proceedings of the 122nd symposium of the Internat. Astronom. Union held in Heidelberg, FRG, June 23 - 27, 1986 / ed. by I. Appenzeller ...},
  journal   = {Circumstellar matter : proceedings of the 122nd symposium of the Internat. Astronom. Union held in Heidelberg, FRG, June 23 - 27, 1986 / ed. by I. Appenzeller ...},
  publisher = {Reidel},
  address   = {Dordrecht u.a.},
  isbn      = {90-277-2511-X},
  pages     = {73 -- 74},
  year      = {1987},
  language  = {en}
}
@article{DachwaldMikuckiTulaczyketal.2014,
  author    = {Dachwald, Bernd and Mikucki, Jill and Tulaczyk, Slawek and Digel, Ilya and Espe, Clemens and Feldmann, Marco and Francke, Gero and Kowalski, Julia and Xu, Changsheng},
  title     = {IceMole : A maneuverable probe for clean in situ analysis and sampling of subsurface ice and subglacial aquatic ecosystems},
  series = {Annals of Glaciology},
  volume    = {55},
  journal   = {Annals of Glaciology},
  number    = {65},
  publisher = {Cambridge University Press},
  address   = {Cambridge},
  issn      = {1727-5644},
  doi       = {10.3189/2014AoG65A004},
  pages     = {14 -- 22},
  year      = {2014},
  abstract  = {There is significant interest in sampling subglacial environments for geobiological studies, but they are difficult to access. Existing ice-drilling technologies make it cumbersome to maintain microbiologically clean access for sample acquisition and environmental stewardship of potentially fragile subglacial aquatic ecosystems. The IceMole is a maneuverable subsurface ice probe for clean in situ analysis and sampling of glacial ice and subglacial materials. The design is based on the novel concept of combining melting and mechanical propulsion. It can change melting direction by differential heating of the melting head and optional side-wall heaters. The first two prototypes were successfully tested between 2010 and 2012 on glaciers in Switzerland and Iceland. They demonstrated downward, horizontal and upward melting, as well as curve driving and dirt layer penetration. A more advanced probe is currently under development as part of the Enceladus Explorer (EnEx) project. It offers systems for obstacle avoidance, target detection, and navigation in ice. For the EnEx-IceMole, we will pay particular attention to clean protocols for the sampling of subglacial materials for biogeochemical analysis. We plan to use this probe for clean access into a unique subglacial aquatic environment at Blood Falls, Antarctica, with return of a subglacial brine sample.},
  language  = {en}
}
@article{FingerBraunBil2020,
  author    = {Finger, Felix and Braun, Carsten and Bil, Cees},
  title     = {Impact of Battery Performance on the Initial Sizing of Hybrid-Electric General Aviation Aircraft},
  series = {Journal of Aerospace Engineering},
  volume    = {33},
  journal   = {Journal of Aerospace Engineering},
  number    = {3},
  publisher = {ASCE},
  address   = {Reston, Va.},
  issn      = {1943-5525},
  doi       = {10.1061/(ASCE)AS.1943-5525.0001113},
  year      = {2020},
  abstract  = {Studies suggest that hybrid-electric aircraft have the potential to generate fewer emissions and be inherently quieter when compared to conventional aircraft. By operating combustion engines together with an electric propulsion system, synergistic benefits can be obtained. However, the performance of hybrid-electric aircraft is still constrained by a battery's energy density and discharge rate. In this paper, the influence of battery performance on the gross mass for a four-seat general aviation aircraft with a hybrid-electric propulsion system is analyzed. For this design study, a high-level approach is chosen, using an innovative initial sizing methodology to determine the minimum required aircraft mass for a specific set of requirements and constraints. Only the peak-load shaving operational strategy is analyzed. Both parallel- and serial-hybrid propulsion configurations are considered for two different missions. The specific energy of the battery pack is varied from 200 to 1,000 W⋅h/kg, while the discharge time, and thus the normalized discharge rating (C-rating), is varied between 30 min (2C discharge rate) and 2 min (30C discharge rate). With the peak-load shaving operating strategy, it is desirable for hybrid-electric aircraft to use a light, low capacity battery system to boost performance. For this case, the battery's specific power rating proved to be of much higher importance than for full electric designs, which have high capacity batteries. Discharge ratings of 20C allow a significant take-off mass reduction aircraft. The design point moves to higher wing loadings and higher levels of hybridization if batteries with advanced technology are used.},
  language  = {en}
}
@article{FingerBraunBil2018,
  author    = {Finger, Felix and Braun, Carsten and Bil, Cees},
  title     = {Impact of electric propulsion technology and mission requirements on the performance of VTOL UAVs},
  series = {CEAS Aeronautical Journal},
  volume    = {10},
  journal   = {CEAS Aeronautical Journal},
  number    = {3},
  publisher = {Springer},
  issn      = {1869-5582 print},
  doi       = {10.1007/s13272-018-0352-x},
  pages     = {843},
  year      = {2018},
  abstract  = {One of the engineering challenges in aviation is the design of transitioning vertical take-off and landing (VTOL) aircraft. Thrust-borne flight implies a higher mass fraction of the propulsion system, as well as much increased energy consumption in the take-off and landing phases. This mass increase is typically higher for aircraft with a separate lift propulsion system than for aircraft that use the cruise propulsion system to support a dedicated lift system. However, for a cost-benefit trade study, it is necessary to quantify the impact the VTOL requirement and propulsion configuration has on aircraft mass and size. For this reason, sizing studies are conducted. This paper explores the impact of considering a supplemental electric propulsion system for achieving hovering flight. Key variables in this study, apart from the lift system configuration, are the rotor disk loading and hover flight time, as well as the electrical systems technology level for both batteries and motors. Payload and endurance are typically used as the measures of merit for unmanned aircraft that carry electro-optical sensors, and therefore the analysis focuses on these particular parameters.},
  language  = {en}
}
@article{DachwaldMcDonaldMcInnesetal.2007,
  author    = {Dachwald, Bernd and McDonald, Malcolm and McInnes, Colin R. and Mengali, Giovanni},
  title     = {Impact of Optical Degradation on Solar Sail Mission Performance},
  series = {Journal of Spacecraft and Rockets. 44 (2007), H. 4},
  journal   = {Journal of Spacecraft and Rockets. 44 (2007), H. 4},
  isbn      = {0022-4650},
  pages     = {740 -- 749},
  year      = {2007},
  language  = {en}
}
@article{GoettenHavermannBraunetal.2020,
  author    = {G{\"o}tten, Falk and Havermann, Marc and Braun, Carsten and Marino, Matthew and Bil, Cees},
  title     = {Improved Form Factor for Drag Estimation of Fuselages with Various Cross Sections},
  series = {Journal of Aircraft},
  journal   = {Journal of Aircraft},
  publisher = {AIAA},
  address   = {Reston, Va.},
  issn      = {1533-3868},
  doi       = {10.2514/1.C036032},
  pages     = {1 -- 13},
  year      = {2020},
  abstract  = {The paper presents an aerodynamic investigation of 70 different streamlined bodies with fineness ratios ranging from 2 to 10. The bodies are chosen to idealize both unmanned and small manned aircraft fuselages and feature cross-sectional shapes that vary from circular to quadratic. The study focuses on friction and pressure drag in dependency of the individual body's fineness ratio and cross section. The drag forces are normalized with the respective body's wetted area to comply with an empirical drag estimation procedure. Although the friction drag coefficient then stays rather constant for all bodies, their pressure drag coefficients decrease with an increase in fineness ratio. Referring the pressure drag coefficient to the bodies' cross-sectional areas shows a distinct pressure drag minimum at a fineness ratio of about three. The pressure drag of bodies with a quadratic cross section is generally higher than for bodies of revolution. The results are used to derive an improved form factor that can be employed in a classic empirical drag estimation method. The improved formulation takes both the fineness ratio and cross-sectional shape into account. It shows superior accuracy in estimating streamlined body drag when compared with experimental data and other form factor formulations of the literature.},
  language  = {en}
}
@article{LettiniHavermannGuidettietal.2010,
  author    = {Lettini, Antonio and Havermann, Marc and Guidetti, Marco and Fornaciari, Andrea},
  title     = {Improved functionalities and energy saving potential on mobile machines combining electronics with flow sharing valve and variable displacement pump},
  series = {IFK 7, 7th International Fluid Power Conference, Efficiency through Fluid Power, 7. Internationales Fluidtechnisches Kolloquium, Workshop Proceedings, Vol. 3, Aachen, DE, 22.-24. Mar, 2010},
  journal   = {IFK 7, 7th International Fluid Power Conference, Efficiency through Fluid Power, 7. Internationales Fluidtechnisches Kolloquium, Workshop Proceedings, Vol. 3, Aachen, DE, 22.-24. Mar, 2010},
  publisher = {-},
  isbn      = {978-3-940565-92-1},
  pages     = {103 -- 114},
  year      = {2010},
  language  = {en}
}
@article{HajAyedKustererFunkeetal.2015,
  author    = {Haj Ayed, A. and Kusterer, K. and Funke, Harald and Keinz, Jan and Striegan, Constantin and Bohn, D.},
  title     = {Improvement study for the dry-low-NOx hydrogen micromix combustion technology},
  series = {Propulsion and power research},
  volume    = {Vol. 4},
  journal   = {Propulsion and power research},
  number    = {Iss. 3},
  issn      = {2212-540X},
  doi       = {10.1016/j.jppr.2015.07.003},
  pages     = {132 -- 140},
  year      = {2015},
  language  = {en}
}
@article{ThomaGardiFisheretal.2024,
  author    = {Thoma, Andreas and Gardi, Alessandro and Fisher, Alex and Braun, Carsten},
  title     = {Improving local path planning for UAV flight in challenging environments by refining cost function weights},
  series = {CEAS Aeronautical Journal},
  journal   = {CEAS Aeronautical Journal},
  publisher = {Springer},
  address   = {Wien},
  issn      = {1869-5590 (eISSN)},
  doi       = {10.1007/s13272-024-00741-x},
  pages     = {12 Seiten},
  year      = {2024},
  abstract  = {Unmanned Aerial Vehicles (UAV) constantly gain in versatility. However, more reliable path planning algorithms are required until full autonomous UAV operation is possible. This work investigates the algorithm 3DVFH* and analyses its dependency on its cost function weights in 2400 environments. The analysis shows that the 3DVFH* can find a suitable path in every environment. However, a particular type of environment requires a specific choice of cost function weights. For minimal failure, probability interdependencies between the weights of the cost function have to be considered. This dependency reduces the number of control parameters and simplifies the usage of the 3DVFH*. Weights for costs associated with vertical evasion (pitch cost) and vicinity to obstacles (obstacle cost) have the highest influence on the failure probability of the local path planner. Environments with mainly very tall buildings (like large American city centres) require a preference for horizontal avoidance manoeuvres (achieved with high pitch cost weights). In contrast, environments with medium-to-low buildings (like European city centres) benefit from vertical avoidance manoeuvres (achieved with low pitch cost weights). The cost of the vicinity to obstacles also plays an essential role and must be chosen adequately for the environment. Choosing these two weights ideal is sufficient to reduce the failure probability below 10\%.},
  language  = {en}
}
@article{BullerschenWilhelmiWimmer1985,
  author    = {Bullerschen, Klaus-Gerd and Wilhelmi, Herbert and Wimmer, W.},
  title     = {Influence of non-uniform material properties and water cooling on current density and temperature profiles in arc furnace elektrodes},
  series = {Steel Research. 56 (1985), H. 11},
  journal   = {Steel Research. 56 (1985), H. 11},
  isbn      = {0177-4832},
  pages     = {559 -- 564},
  year      = {1985},
  language  = {en}
}
@article{HavermannKainumaTakayama2005,
  author    = {Havermann, Marc and Kainuma, M. and Takayama, K.},
  title     = {Influence of Physical and Geometrical Parameters on Vortex Rings Generated by a Shock Tube / Havermann, M. ; Kainuma, M. ; Takayama, K.},
  series = {Non-lethal options enhancing security and stability : 3rd European Symposium on Non-Lethal Weapons, May 10 - 12, 2005, Ettlingen, Germany / ICT, Fraunhofer-Institut Chemische Technologie; European Working Group Non-Lethal Weapons},
  journal   = {Non-lethal options enhancing security and stability : 3rd European Symposium on Non-Lethal Weapons, May 10 - 12, 2005, Ettlingen, Germany / ICT, Fraunhofer-Institut Chemische Technologie; European Working Group Non-Lethal Weapons},
  publisher = {ICT},
  address   = {Pfinztal},
  pages     = {getr. Z{\"a}hlung [ca. 600 S.]},
  year      = {2005},
  language  = {en}
}
@article{FingerBilBraun2019,
  author    = {Finger, Felix and Bil, Cees and Braun, Carsten},
  title     = {Initial Sizing Methodology for Hybrid-Electric General Aviation Aircraft},
  series = {Journal of Aircraft},
  volume    = {57},
  journal   = {Journal of Aircraft},
  number    = {2},
  issn      = {1533-3868},
  doi       = {10.2514/1.C035428},
  pages     = {245 -- 255},
  year      = {2019},
  language  = {en}
}
@article{SchmitzBartzHilgeretal.1990,
  author    = {Schmitz, G{\"u}nter and Bartz, R. and Hilger, U. and Siedentop, M.},
  title     = {Intelligent Alcohol Fuel Sensor},
  year      = {1990},
  language  = {en}
}
@article{Dachwald2004,
  author    = {Dachwald, Bernd},
  title     = {Interplanetary Mission Analysis for Non-Perfectly Reflecting Solar Sailcraft Using Evolutionary Neurocontrol},
  series = {Astrodynamics 2003 : proceedings of the AAS/AIAA Astrodynamics Conference held August 3 - 7, 2003, Big Sky, Montana / ed. by Jean de Lafontaine. - Pt. 2. - (Advances in the astronautical sciences ; 116,2)},
  journal   = {Astrodynamics 2003 : proceedings of the AAS/AIAA Astrodynamics Conference held August 3 - 7, 2003, Big Sky, Montana / ed. by Jean de Lafontaine. - Pt. 2. - (Advances in the astronautical sciences ; 116,2)},
  publisher = {Univelt},
  address   = {San Diego, Calif.},
  isbn      = {0-87703-509-1},
  pages     = {1247 -- 1262},
  year      = {2004},
  language  = {en}
}
@article{LoebSchartnerDachwaldetal.2012,
  author    = {Loeb, Horst Wolfgang and Schartner, Karl-Heinz and Dachwald, Bernd and Ohndorf, Andreas and Seboldt, Wolfgang},
  title     = {Interstellar heliopause probe},
  series = {Труды МАИ},
  journal   = {Труды МАИ},
  number    = {60},
  publisher = {Moskauer Staatliches Luftfahrtinstitut (МАИ)},
  address   = {Moskau},
  pages     = {2 -- 2},
  year      = {2012},
  abstract  = {There is common agreement within the scientific community that in order to understand our local galactic environment it will be necessary to send a spacecraft into the region beyond the solar wind termination shock. Considering distances of 200 AU for a new mission, one needs a spacecraft traveling at a speed of close to 10 AU/yr in order to keep the mission duration in the range of less than 25 yrs, a transfer time postulated by European Space Agency (ESA). Two propulsion options for the mission have been proposed and discussed so far: the solar sail propulsion and the ballistic/radioisotope-electric propulsion (REP). As a further alternative, we here investigate a combination of solar-electric propulsion (SEP) and REP. The SEP stage consists of six 22-cms diameter RIT-22 ion thrusters working with a high specific impulse of 7377 s corresponding to a positive grid voltage of 5 kV. Solar power of 53 kW at begin of mission (BOM) is provided by a lightweight solar array.},
  language  = {en}
}
@article{HeinEubanksHibberdetal.2020,
  author    = {Hein, Andreas M. and Eubanks, T. Marshall and Hibberd, Adam and Fries, Dan and Schneider, Jean and Lingam, Manasvi and Kennedy, Robert and Perakis, Nikolaos and Dachwald, Bernd and Kervella, Pierre},
  title     = {Interstellar Now! Missions to and sample returns from nearby interstellar objects},
  publisher = {Elsevier},
  address   = {Amsterdam},
  pages     = {1 -- 8},
  year      = {2020},
  abstract  = {The recently discovered first high velocity hyperbolic objects passing through the Solar System, 1I/'Oumuamua and 2I/Borisov, have raised the question about near term missions to Interstellar Objects. In situ spacecraft exploration of these objects will allow the direct determination of both their structure and their chemical and isotopic composition, enabling an entirely new way of studying small bodies from outside our solar system. In this paper, we map various Interstellar Object classes to mission types, demonstrating that missions to a range of Interstellar Object classes are feasible, using existing or near-term technology. We describe flyby, rendezvous and sample return missions to interstellar objects, showing various ways to explore these bodies characterizing their surface, dynamics, structure and composition. Interstellar objects likely formed very far from the solar system in both time and space; their direct exploration will constrain their formation and history, situating them within the dynamical and chemical evolution of the Galaxy. These mission types also provide the opportunity to explore solar system bodies and perform measurements in the far outer solar system.},
  language  = {en}
}