@article{BlankeHagenkampDoeringetal.2021,
  author    = {Blanke, Tobias and Hagenkamp, Markus and D{\"o}ring, Bernd and G{\"o}ttsche, Joachim and Reger, Vitali and Kuhnhenne, Markus},
  title     = {Net-exergetic, hydraulic and thermal optimization of coaxial heat exchangers using fixed flow conditions instead of fixed flow rates},
  series = {Geothermal Energy},
  volume    = {9},
  journal   = {Geothermal Energy},
  number    = {Article number: 19},
  publisher = {Springer},
  address   = {Berlin},
  issn      = {2195-9706},
  doi       = {10.1186/s40517-021-00201-3},
  pages     = {23 Seiten},
  year      = {2021},
  abstract  = {Previous studies optimized the dimensions of coaxial heat exchangers using constant mass fow rates as a boundary condition. They show a thermal optimal circular ring width of nearly zero. Hydraulically optimal is an inner to outer pipe radius ratio of 0.65 for turbulent and 0.68 for laminar fow types. In contrast, in this study, fow conditions in the circular ring are kept constant (a set of fxed Reynolds numbers) during optimization. This approach ensures fxed fow conditions and prevents inappropriately high or low mass fow rates. The optimization is carried out for three objectives: Maximum energy gain, minimum hydraulic efort and eventually optimum net-exergy balance. The optimization changes the inner pipe radius and mass fow rate but not the Reynolds number of the circular ring. The thermal calculations base on Hellstr{\"o}m's borehole resistance and the hydraulic optimization on individually calculated linear loss of head coefcients. Increasing the inner pipe radius results in decreased hydraulic losses in the inner pipe but increased losses in the circular ring. The net-exergy diference is a key performance indicator and combines thermal and hydraulic calculations. It is the difference between thermal exergy fux and hydraulic efort. The Reynolds number in the circular ring is instead of the mass fow rate constant during all optimizations. The result from a thermal perspective is an optimal width of the circular ring of nearly zero. The hydraulically optimal inner pipe radius is 54\% of the outer pipe radius for laminar fow and 60\% for turbulent fow scenarios. Net-exergetic optimization shows a predominant infuence of hydraulic losses, especially for small temperature gains. The exact result depends on the earth's thermal properties and the fow type. Conclusively, coaxial geothermal probes' design should focus on the hydraulic optimum and take the thermal optimum as a secondary criterion due to the dominating hydraulics.},
  language  = {en}
}
@phdthesis{Jung2021,
  author    = {Jung, Alexander},
  title     = {Electromechanical modelling and simulation of hiPSC-derived cardiac cell cultures},
  publisher = {Universit{\"a}t Duisburg-Essen},
  isbn      = {978-3-9821811-1-0},
  url       = {http://nbn-resolving.de/https://nbn-resolving.org/urn:nbn:de:hbz:464-20210624-134942-7},
  pages     = {III, 135 Seiten},
  year      = {2021},
  language  = {en}
}
@inproceedings{TranStaat2021,
  author    = {Tran, Ngoc Trinh and Staat, Manfred},
  title     = {FEM shakedown analysis of Kirchhoff-Love plates under uncertainty of strength},
  series = {Proceedings of UNCECOMP 2021},
  booktitle = {Proceedings of UNCECOMP 2021},
  isbn      = {978-618-85072-6-5},
  doi       = {10.7712/120221.8041.19047},
  pages     = {323 -- 338},
  year      = {2021},
  abstract  = {A new formulation to calculate the shakedown limit load of Kirchhoff plates under stochastic conditions of strength is developed. Direct structural reliability design by chance con-strained programming is based on the prescribed failure probabilities, which is an effective approach of stochastic programming if it can be formulated as an equivalent deterministic optimization problem. We restrict uncertainty to strength, the loading is still deterministic. A new formulation is derived in case of random strength with lognormal distribution. Upper bound and lower bound shakedown load factors are calculated simultaneously by a dual algorithm.},
  language  = {en}
}
@article{GoettenFingerHavermannetal.2021,
  author    = {G{\"o}tten, Falk and Finger, Felix and Havermann, Marc and Braun, Carsten and Marino, M. and Bil, C.},
  title     = {Full configuration drag estimation of short-to-medium range fixed-wing UAVs and its impact on initial sizing optimization},
  series = {CEAS Aeronautical Journal},
  volume    = {12},
  journal   = {CEAS Aeronautical Journal},
  publisher = {Springer},
  address   = {Berlin},
  issn      = {1869-5590 (Online)},
  doi       = {10.1007/s13272-021-00522-w},
  pages     = {589 -- 603},
  year      = {2021},
  abstract  = {The paper presents the derivation of a new equivalent skin friction coefficient for estimating the parasitic drag of short-to-medium range fixed-wing unmanned aircraft. The new coefficient is derived from an aerodynamic analysis of ten different unmanned aircraft used for surveillance, reconnaissance, and search and rescue missions. The aircraft is simulated using a validated unsteady Reynolds-averaged Navier Stokes approach. The UAV's parasitic drag is significantly influenced by the presence of miscellaneous components like fixed landing gears or electro-optical sensor turrets. These components are responsible for almost half of an unmanned aircraft's total parasitic drag. The new equivalent skin friction coefficient accounts for these effects and is significantly higher compared to other aircraft categories. It is used to initially size an unmanned aircraft for a typical reconnaissance mission. The improved parasitic drag estimation yields a much heavier unmanned aircraft when compared to the sizing results using available drag data of manned aircraft.},
  language  = {en}
}
@inproceedings{HueningStuettgen2021,
  author    = {H{\"u}ning, Felix and St{\"u}ttgen, Marcel},
  title     = {Work in Progress: Interdisciplinary projects in times of COVID-19 crisis - challenges, risks and chances},
  series = {2021 IEEE Global Engineering Education Conference (EDUCON)},
  booktitle = {2021 IEEE Global Engineering Education Conference (EDUCON)},
  doi       = {10.1109/EDUCON46332.2021.9454006},
  pages     = {1175 -- 1179},
  year      = {2021},
  language  = {en}
}
@inproceedings{HoegenDonckerBragardetal.2021,
  author    = {Hoegen, Anne von and Doncker, Rik W. De and Bragard, Michael and Hoegen, Svenja von},
  title     = {Problem-Based Learning in Automation Engineering: Performing a Remote Laboratory Session Serving Various Educational Attainments},
  series = {2021 IEEE Global Engineering Education Conference (EDUCON)},
  booktitle = {2021 IEEE Global Engineering Education Conference (EDUCON)},
  doi       = {10.1109/EDUCON46332.2021.9453925},
  pages     = {1605 -- 1614},
  year      = {2021},
  language  = {en}
}
@article{BallVoegeleGrajewskietal.2021,
  author    = {Ball, Christopher Stephen and V{\"o}gele, Stefan and Grajewski, Matthias and Kuckshinrichs, Wilhelm},
  title     = {E-mobility from a multi-actor point of view: Uncertainties and their impacts},
  series = {Technological Forecasting and Social Change},
  volume    = {170},
  journal   = {Technological Forecasting and Social Change},
  number    = {Art. 120925},
  publisher = {Elsevier},
  address   = {Amsterdam},
  isbn      = {0040-1625},
  doi       = {10.1016/j.techfore.2021.120925},
  year      = {2021},
  language  = {en}
}
@article{GriegerSchwabedalWendeletal.2021,
  author    = {Grieger, Niklas and Schwabedal, Justus T. C. and Wendel, Stefanie and Ritze, Yvonne and Bialonski, Stephan},
  title     = {Automated scoring of pre-REM sleep in mice with deep learning},
  series = {Scientific Reports},
  volume    = {11},
  journal   = {Scientific Reports},
  number    = {Art. 12245},
  publisher = {Springer Nature},
  address   = {London},
  issn      = {2045-2322},
  doi       = {10.1038/s41598-021-91286-0},
  year      = {2021},
  abstract  = {Reliable automation of the labor-intensive manual task of scoring animal sleep can facilitate the analysis of long-term sleep studies. In recent years, deep-learning-based systems, which learn optimal features from the data, increased scoring accuracies for the classical sleep stages of Wake, REM, and Non-REM. Meanwhile, it has been recognized that the statistics of transitional stages such as pre-REM, found between Non-REM and REM, may hold additional insight into the physiology of sleep and are now under vivid investigation. We propose a classification system based on a simple neural network architecture that scores the classical stages as well as pre-REM sleep in mice. When restricted to the classical stages, the optimized network showed state-of-the-art classification performance with an out-of-sample F1 score of 0.95 in male C57BL/6J mice. When unrestricted, the network showed lower F1 scores on pre-REM (0.5) compared to the classical stages. The result is comparable to previous attempts to score transitional stages in other species such as transition sleep in rats or N1 sleep in humans. Nevertheless, we observed that the sequence of predictions including pre-REM typically transitioned from Non-REM to REM reflecting sleep dynamics observed by human scorers. Our findings provide further evidence for the difficulty of scoring transitional sleep stages, likely because such stages of sleep are under-represented in typical data sets or show large inter-scorer variability. We further provide our source code and an online platform to run predictions with our trained network.},
  language  = {en}
}
@article{EngelmannShalabyShashaetal.2021,
  author    = {Engelmann, Ulrich M. and Shalaby, Ahmed and Shasha, Carolyn and Krishnan, Kannan M. and Krause, Hans-Joachim},
  title     = {Comparative modeling of frequency mixing measurements of magnetic nanoparticles using micromagnetic simulations and Langevin theory},
  series = {Nanomaterials},
  volume    = {11},
  journal   = {Nanomaterials},
  number    = {5},
  publisher = {MDPI},
  address   = {Basel},
  isbn      = {2079-4991},
  doi       = {10.3390/nano11051257},
  pages     = {1 -- 16},
  year      = {2021},
  abstract  = {Dual frequency magnetic excitation of magnetic nanoparticles (MNP) enables enhanced biosensing applications. This was studied from an experimental and theoretical perspective: nonlinear sum-frequency components of MNP exposed to dual-frequency magnetic excitation were measured as a function of static magnetic offset field. The Langevin model in thermodynamic equilibrium was fitted to the experimental data to derive parameters of the lognormal core size distribution. These parameters were subsequently used as inputs for micromagnetic Monte-Carlo (MC)-simulations. From the hysteresis loops obtained from MC-simulations, sum-frequency components were numerically demodulated and compared with both experiment and Langevin model predictions. From the latter, we derived that approximately 90\% of the frequency mixing magnetic response signal is generated by the largest 10\% of MNP. We therefore suggest that small particles do not contribute to the frequency mixing signal, which is supported by MC-simulation results. Both theoretical approaches describe the experimental signal shapes well, but with notable differences between experiment and micromagnetic simulations. These deviations could result from Brownian relaxations which are, albeit experimentally inhibited, included in MC-simulation, or (yet unconsidered) cluster-effects of MNP, or inaccurately derived input for MC-simulations, because the largest particles dominate the experimental signal but concurrently do not fulfill the precondition of thermodynamic equilibrium required by Langevin theory.},
  language  = {en}
}
@article{BerneckerBoyerGathmann2021,
  author    = {Bernecker, Andreas and Boyer, Pierre C. and Gathmann, Christina},
  title     = {The Role of Electoral Incentives for Policy Innovation: Evidence from the US Welfare Reform},
  series = {American Economic Journal: Economic Policy},
  volume    = {13},
  journal   = {American Economic Journal: Economic Policy},
  number    = {2},
  publisher = {American Economic Association},
  address   = {Nashville, Tenn.},
  issn      = {1945-774X},
  doi       = {10.1257/pol.20190690},
  pages     = {26 -- 57},
  year      = {2021},
  language  = {en}
}
@article{ValeroSchalkoFriedrichetal.2021,
  author    = {Valero, Daniel and Schalko, Isabella and Friedrich, Heide and Abad, Jorge D. and Bung, Daniel B. and Donchyts, Gennadii and Felder, Stefan and Ferreira, Rui M. L. and Hohermuth, Benjamin and Kramer, Matthias and Li, Danxun and Mendes, Luis and Moreno-Rodenas, Antonio and Nones, Michael and Paron, Paolo and Ruiz-Villanueva, Virginia and Wang, Ruo-Qian and Franca, Mario J.},
  title     = {Pathways towards democratization of hydro-environment observations and data},
  series = {Iahr White Paper Series},
  journal   = {Iahr White Paper Series},
  number    = {1},
  publisher = {International Association for Hydro-Environment Engineering and Research (IAHR)},
  pages     = {1 -- 9},
  year      = {2021},
  language  = {en}
}
@article{NeumaierKotliarHaerenetal.2021,
  author    = {Neumaier, Felix and Kotliar, Konstantin and Haeren, Roel Hubert Louis and Temel, Yasin and L{\"u}ke, Jan Niklas and Seyam, Osama and Lindauer, Ute and Clusmann, Hans and Hescheler, J{\"u}rgen and Schubert, Gerrit Alexander and Schneider, Toni and Albanna, Walid},
  title     = {Retinal Vessel Responses to Flicker Stimulation Are Impaired in Ca v 2.3-Deficient Mice—An in- vivo Evaluation Using Retinal Vessel Analysis (RVA)},
  series = {Frontiers in Neurology},
  volume    = {12},
  journal   = {Frontiers in Neurology},
  publisher = {Frontiers},
  doi       = {10.3389/fneur.2021.659890},
  pages     = {1 -- 11},
  year      = {2021},
  language  = {en}
}
@article{HacklNacovKammerlohretal.2021,
  author    = {Hackl, Michael and Nacov, Julia and Kammerlohr, Sandra and Staat, Manfred and Buess, Eduard and Leschinger, Tim and M{\"u}ller, Lars P. and Wegmann, Kilian},
  title     = {Intratendinous Strain Variations of the Supraspinatus Tendon Depending on Repair Technique: A Biomechanical Analysis Regarding the Cause of Medial Cuff Failure},
  series = {The American Journal of Sports Medicine},
  volume    = {49},
  journal   = {The American Journal of Sports Medicine},
  number    = {7},
  publisher = {Sage},
  address   = {London},
  issn      = {1552-3365},
  doi       = {10.1177/03635465211006138},
  pages     = {1847 -- 1853},
  year      = {2021},
  language  = {en}
}
@article{HarzheimMuehmelHeuermann2021,
  author    = {Harzheim, Thomas and M{\"u}hmel, Marc and Heuermann, Holger},
  title     = {A SFCW harmonic radar system for maritime search and rescue using passive and active tags},
  series = {International Journal of Microwave and Wireless Technologies},
  volume    = {13},
  journal   = {International Journal of Microwave and Wireless Technologies},
  number    = {Special Issue 7},
  publisher = {Cambridge University Press},
  address   = {Cambridge},
  doi       = {10.1017/S1759078721000520},
  pages     = {691 -- 707},
  year      = {2021},
  abstract  = {This paper introduces a new maritime search and rescue system based on S-band illumination harmonic radar (HR). Passive and active tags have been developed and tested while attached to life jackets and a small boat. In this demonstration test carried out on the Baltic Sea, the system was able to detect and range the active tags up to a distance of 5800 m using an illumination signal transmit-power of 100 W. Special attention is given to the development, performance, and conceptual differences between passive and active tags used in the system. Guidelines for achieving a high HR dynamic range, including a system components description, are given and a comparison with other HR systems is performed. System integration with a commercial maritime X-band navigation radar is shown to demonstrate a solution for rapid search and rescue response and quick localization.},
  language  = {en}
}
@article{HugenrothNeidlinEngelmannetal.2021,
  author    = {Hugenroth, Kristin and Neidlin, Michael and Engelmann, Ulrich M. and Kaufmann, Tim A. S. and Steinseifer, Ulrich and Heilmann, Torsten},
  title     = {Tipless Transseptal Cannula Concept Combines Improved Hemodynamic Properties and Risk-Reduced Placement: an In Silico Proof-of-Concept},
  series = {Artificial Organs},
  journal   = {Artificial Organs},
  number    = {Accepted Article},
  publisher = {Wiley},
  address   = {Weinheim},
  issn      = {1525-1594},
  doi       = {10.1111/aor.13964},
  year      = {2021},
  language  = {en}
}
@article{GoettenHavermannBraunetal.2021,
  author    = {G{\"o}tten, Falk and Havermann, Marc and Braun, Carsten and Marino, Matthew and Bil, Cees},
  title     = {Aerodynamic Investigations of UAV Sensor Turrets - A Combined Wind-tunnel and CFD Approach},
  series = {SciTech 2021, AIAA SciTech Forum, online, WW, Jan 11-15, 2021},
  journal   = {SciTech 2021, AIAA SciTech Forum, online, WW, Jan 11-15, 2021},
  publisher = {AIAA},
  address   = {Reston, Va.},
  doi       = {10.2514/6.2021-1535},
  pages     = {1 -- 12},
  year      = {2021},
  language  = {en}
}
@inproceedings{FerreinMeessenLimpertetal.2021,
  author    = {Ferrein, Alexander and Meeßen, Marcus and Limpert, Nicolas and Schiffer, Stefan},
  title     = {Compiling ROS Schooling Curricula via Contentual Taxonomies},
  series = {Robotics in Education},
  booktitle = {Robotics in Education},
  editor    = {Lepuschitz, Wilfried},
  publisher = {Springer},
  address   = {Cham},
  isbn      = {978-3-030-67411-3},
  doi       = {10.1007/978-3-030-67411-3_5},
  pages     = {49 -- 60},
  year      = {2021},
  language  = {en}
}
@article{BechtSchollmayerMonakhovaetal.2021,
  author    = {Becht, Alexander and Schollmayer, Curd and Monakhova, Yulia and Holzgrabe, Ulrike},
  title     = {Tracing the origin of paracetamol tablets by near-infrared, mid-infrared, and nuclear magnetic resonance spectroscopy using principal component analysis and linear discriminant analysis},
  series = {Analytical and Bioanalytical Chemistry},
  volume    = {413},
  journal   = {Analytical and Bioanalytical Chemistry},
  publisher = {Springer Nature},
  issn      = {1618-2650},
  doi       = {10.1007/s00216-021-03249-z},
  pages     = {3107 -- 3118},
  year      = {2021},
  abstract  = {Most drugs are no longer produced in their own countries by the pharmaceutical companies, but by contract manufacturers or at manufacturing sites in countries that can produce more cheaply. This not only makes it difficult to trace them back but also leaves room for criminal organizations to fake them unnoticed. For these reasons, it is becoming increasingly difficult to determine the exact origin of drugs. The goal of this work was to investigate how exactly this is possible by using different spectroscopic methods like nuclear magnetic resonance and near- and mid-infrared spectroscopy in combination with multivariate data analysis. As an example, 56 out of 64 different paracetamol preparations, collected from 19 countries around the world, were chosen to investigate whether it is possible to determine the pharmaceutical company, manufacturing site, or country of origin. By means of suitable pre-processing of the spectra and the different information contained in each method, principal component analysis was able to evaluate manufacturing relationships between individual companies and to differentiate between production sites or formulations. Linear discriminant analysis showed different results depending on the spectral method and purpose. For all spectroscopic methods, it was found that the classification of the preparations to their manufacturer achieves better results than the classification to their pharmaceutical company. The best results were obtained with nuclear magnetic resonance and near-infrared data, with 94.6\%/99.6\% and 98.7/100\% of the spectra of the preparations correctly assigned to their pharmaceutical company or manufacturer.},
  language  = {en}
}
@article{MonakhovaDiehl2021,
  author    = {Monakhova, Yulia and Diehl, Bernd W. K.},
  title     = {A step towards optimization of the qNMR workflow: proficiency testing exercise at an GxP-accredited laboratory},
  series = {Applied Magnetic Resonance},
  volume    = {52},
  journal   = {Applied Magnetic Resonance},
  publisher = {Springer Nature},
  address   = {Wien},
  issn      = {1613-7507},
  doi       = {10.1007/s00723-021-01324-3},
  pages     = {581 -- 593},
  year      = {2021},
  abstract  = {Quantitative nuclear magnetic resonance (qNMR) is considered as a powerful tool for multicomponent mixture analysis as well as for the purity determination of single compounds. Special attention is currently paid to the training of operators and study directors involved in qNMR testing. To assure that only qualified personnel are used for sample preparation at our GxP-accredited laboratory, weighing test was proposed. Sixteen participants performed six-fold weighing of the binary mixture of dibutylated hydroxytoluene (BHT) and 1,2,4,5-tetrachloro-3-nitrobenzene (TCNB). To evaluate the quality of data analysis, all spectra were evaluated manually by a qNMR expert and using in-house developed automated routine. The results revealed that mean values are comparable and both evaluation approaches are free of systematic error. However, automated evaluation resulted in an approximately 20\% increase in precision. The same findings were revealed for qNMR analysis of 32 compounds used in pharmaceutical industry. Weighing test by six-fold determination in binary mixtures and automated qNMR methodology can be recommended as efficient tools for evaluating staff proficiency. The automated qNMR method significantly increases throughput and precision of qNMR for routine measurements and extends application scope of qNMR.},
  language  = {en}
}
@article{BohndickBosseJaenschetal.2021,
  author    = {Bohndick, Carla and Bosse, Elke and J{\"a}nsch, Vanessa K. and Barnat, Miriam},
  title     = {How different diversity factors affect the perception of first-year requirements in higher education},
  series = {Frontline Learning Research},
  volume    = {9},
  journal   = {Frontline Learning Research},
  number    = {2},
  publisher = {EARLI},
  issn      = {2295-3159},
  doi       = {10.14786/flr.v9i2.667},
  pages     = {78 -- 95},
  year      = {2021},
  abstract  = {In the light of growing university entry rates, higher education institutions not only serve larger numbers of students, but also seek to meet first-year students' ever more diverse needs. Yet to inform universities how to support the transition to higher education, research only offers limited insights. Current studies tend to either focus on the individual factors that affect student success or they highlight students' social background and their educational biography in order to examine the achievement of selected, non-traditional groups of students. Both lines of research appear to lack integration and often fail to take organisational diversity into account, such as different types of higher education institutions or degree programmes. For a more comprehensive understanding of student diversity, the present study includes individual, social and organisational factors. To gain insights into their role for the transition to higher education, we examine how the different factors affect the students' perception of the formal and informal requirements of the first year as more or less difficult to cope with. As the perceived requirements result from both the characteristics of the students and the institutional context, they allow to investigate transition at the interface of the micro and the meso level of higher education. Latent profile analyses revealed that there are no profiles with complex patterns of perception of the first-year requirements, but the identified groups rather differ in the overall level of perceived challenges. Moreover, SEM indicates that the differences in the perception largely depend on the individual factors self-efficacy and volition.},
  language  = {en}
}
@article{WaldvogelRitzmannFreyleretal.2021,
  author    = {Waldvogel, Janice and Ritzmann, Ramona and Freyler, Kathrin and Helm, Michael and Monti, Elena and Albracht, Kirsten and St{\"a}udle, Benjamin and Gollhofer, Albert and Narici, Marco},
  title     = {The Anticipation of Gravity in Human Ballistic Movement},
  series = {Frontiers in Physiology},
  journal   = {Frontiers in Physiology},
  publisher = {Frontiers},
  address   = {Lausanne},
  issn      = {1664-042X},
  doi       = {10.3389/fphys.2021.614060},
  year      = {2021},
  abstract  = {Stretch-shortening type actions are characterized by lengthening of the pre-activated muscle-tendon unit (MTU) in the eccentric phase immediately followed by muscle shortening. Under 1 g, pre-activity before and muscle activity after ground contact, scale muscle stiffness, which is crucial for the recoil properties of the MTU in the subsequent push-off. This study aimed to examine the neuro-mechanical coupling of the stretch-shortening cycle in response to gravity levels ranging from 0.1 to 2 g. During parabolic flights, 17 subjects performed drop jumps while electromyography (EMG) of the lower limb muscles was combined with ultrasound images of the gastrocnemius medialis, 2D kinematics and kinetics to depict changes in energy management and performance. Neuro-mechanical coupling in 1 g was characterized by high magnitudes of pre-activity and eccentric muscle activity allowing an isometric muscle behavior during ground contact. EMG during pre-activity and the concentric phase systematically increased from 0.1 to 1 g. Below 1 g the EMG in the eccentric phase was diminished, leading to muscle lengthening and reduced MTU stretches. Kinetic energy at take-off and performance were decreased compared to 1 g. Above 1 g, reduced EMG in the eccentric phase was accompanied by large MTU and muscle stretch, increased joint flexion amplitudes, energy loss and reduced performance. The energy outcome function established by linear mixed model reveals that the central nervous system regulates the extensor muscles phase- and load-specifically. In conclusion, neuro-mechanical coupling appears to be optimized in 1 g. Below 1 g, the energy outcome is compromised by reduced muscle stiffness. Above 1 g, loading progressively induces muscle lengthening, thus facilitating energy dissipation.},
  language  = {en}
}
@article{LowisFergusonPaulssenetal.2021,
  author    = {Lowis, Carsten and Ferguson, Simon and Paulßen, Elisabeth and Hoehr, Cornelia},
  title     = {Improved Sc-44 production in a siphon-style liquid target on a medical cyclotron},
  series = {Applied Radiation and Isotopes},
  volume    = {172},
  journal   = {Applied Radiation and Isotopes},
  number    = {Art. 109675},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0969-8043},
  doi       = {10.1016/j.apradiso.2021.109675},
  year      = {2021},
  language  = {en}
}
@article{WertIkenSchoeningetal.2021,
  author    = {Wert, Stefan and Iken, Heiko and Sch{\"o}ning, Michael Josef and Matysik, Frank-Michael},
  title     = {Development of a temperature-pulse enhanced electrochemical glucose biosensor and characterization of its stability via scanning electrochemical microscopy},
  series = {Electroanalysis},
  journal   = {Electroanalysis},
  number    = {Early View},
  publisher = {Wiley-VCH},
  address   = {Weinheim},
  issn      = {1521-4109},
  doi       = {10.1002/elan.202100089},
  year      = {2021},
  abstract  = {Glucose oxidase (GOx) is an enzyme frequently used in glucose biosensors. As increased temperatures can enhance the performance of electrochemical sensors, we investigated the impact of temperature pulses on GOx that was drop-coated on flattened Pt microwires. The wires were heated by an alternating current. The sensitivity towards glucose and the temperature stability of GOx was investigated by amperometry. An up to 22-fold increase of sensitivity was observed. Spatially resolved enzyme activity changes were investigated via scanning electrochemical microscopy. The application of short (<100 ms) heat pulses was associated with less thermal inactivation of the immobilized GOx than long-term heating.},
  language  = {en}
}
@article{Maurischat2021,
  author    = {Maurischat, Andreas},
  title     = {Algebraic independence of the Carlitz period and its hyperderivatives},
  pages     = {1 -- 12},
  year      = {2021},
  language  = {en}
}
@inproceedings{ElMoussaouiKassmiAlexopoulosetal.2021,
  author    = {El Moussaoui, Noureddine and Kassmi, Khalil and Alexopoulos, Spiros and Schwarzer, Klemens and Chayeb, Hamid and Bachiri, Najib},
  title     = {Simulation studies on a new innovative design of a hybrid solar distiller MSDH alimented with a thermal and photovoltaic energy},
  series = {Materialstoday: Proceedings},
  booktitle = {Materialstoday: Proceedings},
  issn      = {2214-7853},
  doi       = {10.1016/j.matpr.2021.03.115},
  year      = {2021},
  language  = {en}
}
@article{MolinnusDrinicIkenetal.2021,
  author    = {Molinnus, Denise and Drinic, Aleksander and Iken, Heiko and Kr{\"o}ger, Nadja and Zinser, Max and Smeets, Ralf and K{\"o}pf, Marius and Kopp, Alexander and Sch{\"o}ning, Michael Josef},
  title     = {Towards a flexible electrochemical biosensor fabricated from biocompatible Bombyx mori silk},
  series = {Biosensors and Bioelectronics},
  volume    = {183},
  journal   = {Biosensors and Bioelectronics},
  number    = {Art. 113204},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0956-5663},
  doi       = {10.1016/j.bios.2021.113204},
  year      = {2021},
  language  = {en}
}
@phdthesis{Bayer2021,
  author    = {Bayer, Robin},
  title     = {Development of a novel in-vitro vascular model for determination of physiological and pathophysiological mechanobiology},
  publisher = {Universit{\"a}t zu K{\"o}ln},
  address   = {K{\"o}ln},
  url       = {http://nbn-resolving.de/urn:nbn:de:hbz:38-362212},
  pages     = {IV, 115 Seiten},
  year      = {2021},
  language  = {en}
}
@article{JildehWagnerSchoening2021,
  author    = {Jildeh, Zaid B. and Wagner, Patrick H. and Sch{\"o}ning, Michael Josef},
  title     = {Sterilization of Objects, Products, and Packaging Surfaces and Their Characterization in Different Fields of Industry: The Status in 2020},
  series = {physica status solidi (a) applications and materials science},
  volume    = {218},
  journal   = {physica status solidi (a) applications and materials science},
  number    = {13},
  publisher = {Wiley-VCH},
  address   = {Weinheim},
  issn      = {1862-6319},
  doi       = {10.1002/pssa.202000732},
  pages     = {27 Seiten},
  year      = {2021},
  abstract  = {The treatment method to deactivate viable microorganisms from objects or products is termed sterilization. There are multiple forms of sterilization, each intended to be applied for a specific target, which depends on—but not limited to—the thermal, physical, and chemical stability of that target. Herein, an overview on the currently used sterilization processes in the global market is provided. Different sterilization techniques are grouped under a category that describes the method of treatment: radiation (gamma, electron beam, X-ray, and ultraviolet), thermal (dry and moist heat), and chemical (ethylene oxide, ozone, chlorine dioxide, and hydrogen peroxide). For each sterilization process, the typical process parameters as defined by regulations and the mode of antimicrobial activity are summarized. Finally, the recommended microorganisms that are used as biological indicators to validate sterilization processes in accordance with the rules that are established by various regulatory agencies are summarized.},
  language  = {en}
}
@article{YoshinobuSchoening2021,
  author    = {Yoshinobu, Tatsuo and Sch{\"o}ning, Michael Josef},
  title     = {Light-addressable potentiometric sensors (LAPS) for cell monitoring and biosensing},
  series = {Current Opinion in Electrochemistry},
  journal   = {Current Opinion in Electrochemistry},
  number    = {In Press, Journal Pre-proof},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {2451-9103},
  doi       = {10.1016/j.coelec.2021.100727},
  year      = {2021},
  language  = {en}
}
@article{BergsMonakhovaDiehletal.2021,
  author    = {Bergs, Michel and Monakhova, Yulia and Diehl, Bernd W. and Konow, Christopher and V{\"o}lkering, Georg and Pude, Ralf and Schulze, Margit},
  title     = {Lignins isolated via catalyst-free organosolv pulping from Miscanthus x giganteus, M. sinensis, M. robustus and M. nagara: a comparative study},
  series = {Molecules},
  volume    = {26},
  journal   = {Molecules},
  number    = {4},
  publisher = {MDPI},
  address   = {Basel},
  issn      = {1420-3049},
  doi       = {10.3390/molecules26040842},
  year      = {2021},
  abstract  = {As a low-input crop, Miscanthus offers numerous advantages that, in addition to agricultural applications, permits its exploitation for energy, fuel, and material production. Depending on the Miscanthus genotype, season, and harvest time as well as plant component (leaf versus stem), correlations between structure and properties of the corresponding isolated lignins differ. Here, a comparative study is presented between lignins isolated from M. x giganteus, M. sinensis, M. robustus and M. nagara using a catalyst-free organosolv pulping process. The lignins from different plant constituents are also compared regarding their similarities and differences regarding monolignol ratio and important linkages. Results showed that the plant genotype has the weakest influence on monolignol content and interunit linkages. In contrast, structural differences are more significant among lignins of different harvest time and/or season. Analyses were performed using fast and simple methods such as nuclear magnetic resonance (NMR) spectroscopy. Data was assigned to four different linkages (A: β-O-4 linkage, B: phenylcoumaran, C: resinol, D: β-unsaturated ester). In conclusion, A content is particularly high in leaf-derived lignins at just under 70\% and significantly lower in stem and mixture lignins at around 60\% and almost 65\%. The second most common linkage pattern is D in all isolated lignins, the proportion of which is also strongly dependent on the crop portion. Both stem and mixture lignins, have a relatively high share of approximately 20\% or more (maximum is M. sinensis Sin2 with over 30\%). In the leaf-derived lignins, the proportions are significantly lower on average. Stem samples should be chosen if the highest possible lignin content is desired, specifically from the M. x giganteus genotype, which revealed lignin contents up to 27\%. Due to the better frost resistance and higher stem stability, M. nagara offers some advantages compared to M. x giganteus. Miscanthus crops are shown to be very attractive lignocellulose feedstock (LCF) for second generation biorefineries and lignin generation in Europe.},
  language  = {en}
}
@inproceedings{SchulteEggert2021,
  author    = {Schulte, Maximilian and Eggert, Mathias},
  title     = {Predicting hourly bitcoin prices based on long short-term memory neural networks},
  series = {Proceedings of the International Conference on Wirtschaftsinformatik (WI) 2021},
  booktitle = {Proceedings of the International Conference on Wirtschaftsinformatik (WI) 2021},
  pages     = {16 Seiten},
  year      = {2021},
  abstract  = {Bitcoin is a cryptocurrency and is considered a high-risk asset class whose price changes are difficult to predict. Current research focusses on daily price movements with a limited number of predictors. The paper at hand aims at identifying measurable indicators for Bitcoin price movement s and the development of a suitable forecasting model for hourly changes. The paper provides three research contributions. First, a set of significant indicators for predicting the Bitcoin price is identified. Second, the results of a trained Long Short-term Memory (LSTM) neural network that predicts price changes on an hourly basis is presented and compared with other algorithms. Third, the results foster discussions of the applicability of neural nets for stock price predictions. In total, 47 input features for a period of over 10 months could be retrieved to train a neural net that predicts the Bitcoin price movements with an error rate of 3.52 \%.},
  language  = {en}
}
@inproceedings{FunkeBeckmannKeinzetal.2021,
  author    = {Funke, Harald and Beckmann, Nils and Keinz, Jan and Horikawa, Atsushi},
  title     = {30 years of dry low NOx micromix combustor research for hydrogen-rich fuels: an overview of past and present activities},
  series = {Proceedings of the ASME Turbo Expo 2020: Turbomachinery Technical Conference and Exposition, September 21-25, 2020, Virtual, Online. Vol.: 4B: Combustion, Fuels, and Emissions},
  booktitle = {Proceedings of the ASME Turbo Expo 2020: Turbomachinery Technical Conference and Exposition, September 21-25, 2020, Virtual, Online. Vol.: 4B: Combustion, Fuels, and Emissions},
  publisher = {American Society of Mechanical Engineers (ASME)},
  isbn      = {978-0-7918-8413-3},
  doi       = {10.1115/GT2020-16328},
  pages     = {14 Seiten},
  year      = {2021},
  language  = {en}
}
@inproceedings{HeuermannHarzheimMuehmel2021,
  author    = {Heuermann, Holger and Harzheim, Thomas and M{\"u}hmel, Marc},
  title     = {A maritime harmonic radar search and rescue system using passive and active tags},
  series = {2020 17th European Radar Conference (EuRAD)},
  booktitle = {2020 17th European Radar Conference (EuRAD)},
  publisher = {IEEE},
  isbn      = {978-2-87487-061-3},
  doi       = {10.1109/EuRAD48048.2021.00030},
  pages     = {73 -- 76},
  year      = {2021},
  language  = {en}
}
@article{JablonskiMuenstermannNorketal.2021,
  author    = {Jablonski, Melanie and M{\"u}nstermann, Felix and Nork, Jasmina and Molinnus, Denise and Muschallik, Lukas and Bongaerts, Johannes and Wagner, Torsten and Keusgen, Michael and Siegert, Petra and Sch{\"o}ning, Michael Josef},
  title     = {Capacitive field-effect biosensor applied for the detection of acetoin in alcoholic beverages and fermentation broths},
  series = {physica status solidi (a) applications and materials science},
  volume    = {218},
  journal   = {physica status solidi (a) applications and materials science},
  number    = {13},
  publisher = {Wiley-VCH},
  address   = {Weinheim},
  issn      = {1862-6319},
  doi       = {10.1002/pssa.202000765},
  pages     = {7 Seiten},
  year      = {2021},
  abstract  = {An acetoin biosensor based on a capacitive electrolyte-insulator-semiconductor (EIS) structure modified with the enzyme acetoin reductase, also known as butane-2,3-diol dehydrogenase (Bacillus clausii DSM 8716ᵀ), is applied for acetoin detection in beer, red wine, and fermentation broth samples for the first time. The EIS sensor consists of an Al/p-Si/SiO₂/Ta₂O₅ layer structure with immobilized acetoin reductase on top of the Ta₂O₅ transducer layer by means of crosslinking via glutaraldehyde. The unmodified and enzyme-modified sensors are electrochemically characterized by means of leakage current, capacitance-voltage, and constant capacitance methods, respectively.},
  language  = {en}
}
@article{GivanoudiCornelisRasschaertetal.2021,
  author    = {Givanoudi, Stella and Cornelis, Peter and Rasschaert, Geertrui and Wackers, Gideon and Iken, Heiko and Rolka, David and Yongabi, Derick and Robbens, Johan and Sch{\"o}ning, Michael Josef and Heyndrickx, Marc and Wagner, Patrick},
  title     = {Selective Campylobacter detection and quantification in poultry: A sensor tool for detecting the cause of a common zoonosis at its source},
  series = {Sensors and Actuators B: Chemical},
  journal   = {Sensors and Actuators B: Chemical},
  number    = {In Press, Journal Pre-proof},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0925-4005},
  doi       = {10.1016/j.snb.2021.129484},
  pages     = {Article 129484},
  year      = {2021},
  language  = {en}
}
@article{JablonskiPoghossianSeverinetal.2021,
  author    = {Jablonski, Melanie and Poghossian, Arshak and Severin, Robin and Keusgen, Michael and Wege, Christian and Sch{\"o}ning, Michael Josef},
  title     = {Capacitive Field-Effect Biosensor Studying Adsorption of Tobacco Mosaic Virus Particles},
  series = {Micromachines},
  volume    = {12},
  journal   = {Micromachines},
  number    = {1},
  publisher = {MDPI},
  address   = {Basel},
  doi       = {10.3390/mi12010057},
  pages     = {Artikel 57},
  year      = {2021},
  abstract  = {Plant virus-like particles, and in particular, tobacco mosaic virus (TMV) particles, are increasingly being used in nano- and biotechnology as well as for biochemical sensing purposes as nanoscaffolds for the high-density immobilization of receptor molecules. The sensitive parameters of TMV-assisted biosensors depend, among others, on the density of adsorbed TMV particles on the sensor surface, which is affected by both the adsorption conditions and surface properties of the sensor. In this work, Ta₂O₅-gate field-effect capacitive sensors have been applied for the label-free electrical detection of TMV adsorption. The impact of the TMV concentration on both the sensor signal and the density of TMV particles adsorbed onto the Ta₂O₅-gate surface has been studied systematically by means of field-effect and scanning electron microscopy methods. In addition, the surface density of TMV particles loaded under different incubation times has been investigated. Finally, the field-effect sensor also demonstrates the label-free detection of penicillinase immobilization as model bioreceptor on TMV particles.},
  language  = {en}
}
@article{ErpicumCrookstonBombardellietal.2021,
  author    = {Erpicum, Sebastien and Crookston, Brian M. and Bombardelli, Fabian and Bung, Daniel B. and Felder, Stefan and Mulligan, Sean and Oertel, Mario and Palermo, Michele},
  title     = {Hydraulic structures engineering: An evolving science in a changing world},
  series = {Wires Water},
  volume    = {8},
  journal   = {Wires Water},
  number    = {2},
  publisher = {Wiley},
  address   = {Weinheim},
  issn      = {2049-1948},
  doi       = {10.1002/wat2.1505},
  year      = {2021},
  language  = {en}
}
@article{FaganBitzBjoerkmanBurtscheretal.2021,
  author    = {Fagan, Andrew J. and Bitz, Andreas and Bj{\"o}rkman-Burtscher, Isabella M. and Collins, Christopher M. and Kimbrell, Vera and Raaijmakers, Alexander J. E.},
  title     = {7T MR Safety},
  series = {Journal of Magnetic Resonance Imaging (JMRI)},
  volume    = {53},
  journal   = {Journal of Magnetic Resonance Imaging (JMRI)},
  number    = {2},
  publisher = {Wiley},
  address   = {Weinheim},
  issn      = {1522-2586},
  doi       = {10.1002/jmri.27319},
  pages     = {333 -- 346},
  year      = {2021},
  language  = {en}
}
@article{SerrorHackHenzeetal.2021,
  author    = {Serror, Martin and Hack, Sacha and Henze, Martin and Schuba, Marko and Wehrle, Klaus},
  title     = {Challenges and Opportunities in Securing the Industrial Internet of Things},
  series = {IEEE Transactions on Industrial Informatics},
  volume    = {17},
  journal   = {IEEE Transactions on Industrial Informatics},
  number    = {5},
  publisher = {IEEE},
  address   = {New York},
  issn      = {1941-0050},
  doi       = {10.1109/TII.2020.3023507},
  pages     = {2985 -- 2996},
  year      = {2021},
  language  = {en}
}
@article{MeyerGranrathFeyerletal.2021,
  author    = {Meyer, Max-Arno and Granrath, Christian and Feyerl, G{\"u}nter and Richenhagen, Johannes and Kaths, Jakob and Andert, Jakob},
  title     = {Closed-loop platoon simulation with cooperative intelligent transportation systems based on vehicle-to-X communication},
  series = {Simulation Modelling Practice and Theory},
  volume    = {106},
  journal   = {Simulation Modelling Practice and Theory},
  number    = {Art. 102173},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1569-190X},
  doi       = {10.1016/j.simpat.2020.102173},
  year      = {2021},
  language  = {en}
}
@article{SeefeldtDachwald2021,
  author    = {Seefeldt, Patric and Dachwald, Bernd},
  title     = {Temperature increase on folded solar sail membranes},
  series = {Advances in Space Research},
  volume    = {67},
  journal   = {Advances in Space Research},
  number    = {9},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0273-1177},
  doi       = {10.1016/j.asr.2020.09.026},
  pages     = {2688 -- 2695},
  year      = {2021},
  language  = {en}
}
@article{TranStaat2021,
  author    = {Tran, Ngoc Trinh and Staat, Manfred},
  title     = {Direct plastic structural design under random strength and random load by chance constrained programming},
  series = {European Journal of Mechanics - A/Solids},
  volume    = {85},
  journal   = {European Journal of Mechanics - A/Solids},
  number    = {Article 104106},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0997-7538},
  doi       = {10.1016/j.euromechsol.2020.104106},
  year      = {2021},
  language  = {en}
}
@article{CapitainWagnerHummeletal.2021,
  author    = {Capitain, Charlotte and Wagner, Sebastian and Hummel, Joana and Tippk{\"o}tter, Nils},
  title     = {Investigation of C-N Formation Between Catechols and Chitosan for the Formation of a Strong, Novel Adhesive Mimicking Mussel Adhesion},
  series = {Waste and Biomass Valorization},
  volume    = {12},
  journal   = {Waste and Biomass Valorization},
  publisher = {Springer Nature},
  address   = {Cham},
  issn      = {1877-265X},
  doi       = {10.1007/s12649-020-01110-5},
  pages     = {1761 -- 1779},
  year      = {2021},
  language  = {en}
}
@article{AkimbekovDigelAbdievaetal.2021,
  author    = {Akimbekov, Nuraly and Digel, Ilya and Abdieva, Gulzhamal and Ualieva, Perizat and Tastambek, Kuanysh},
  title     = {Lignite biosolubilization and bioconversion by Bacillus sp.: the collation of analytical data},
  series = {Biofuels},
  volume    = {12},
  journal   = {Biofuels},
  number    = {3},
  publisher = {Taylor \& Francis},
  address   = {London},
  issn      = {1759-7277},
  pages     = {247 -- 258},
  year      = {2021},
  abstract  = {The vast metabolic potential of microbes in brown coal (lignite) processing and utilization can greatly contribute to innovative approaches to sustainable production of high-value products from coal. In this study, the multi-faceted and complex coal biosolubilization process by Bacillus sp. RKB 7 isolate from the Kazakhstan coal-mining soil is reported, and the derived products are characterized. Lignite solubilization tests performed for surface and suspension cultures testify to the formation of numerous soluble lignite-derived substances. Almost 24\% of crude lignite (5\% w/v) was solubilized within 14 days under slightly alkaline conditions (pH 8.2). FTIR analysis revealed various functional groups in the obtained biosolubilization products. Analyses of the lignite-derived humic products by UV-Vis and fluorescence spectrometry as well as elemental analysis yielded compatible results indicating the emerging products had a lower molecular weight and degree of aromaticity. Furthermore, XRD and SEM analyses were used to evaluate the biosolubilization processes from mineralogical and microscopic points of view. The findings not only contribute to a deeper understanding of microbe-mineral interactions in coal environments, but also contribute to knowledge of coal biosolubilization and bioconversion with regard to sustainable production of humic substances. The detailed and comprehensive analyses demonstrate the huge biotechnological potential of Bacillus sp. for agricultural productivity and environmental health.},
  language  = {en}
}
@article{KoehlerRoepkeWolf2021,
  author    = {K{\"o}hler, Klemens and R{\"o}pke, Ren{\´e} and Wolf, Martin},
  title     = {Through a mirror darkly - On the obscurity of teaching goals in game-based learning in IT security},
  series = {ISAGA 2019: Simulation Gaming Through Times and Disciplines},
  journal   = {ISAGA 2019: Simulation Gaming Through Times and Disciplines},
  publisher = {Springer},
  address   = {Cham},
  doi       = {10.1007/978-3-030-72132-9_6},
  pages     = {61 -- 73},
  year      = {2021},
  abstract  = {Teachers and instructors use very specific language communicating teaching goals. The most widely used frameworks of common reference are the Bloom's Taxonomy and the Revised Bloom's Taxonomy. The latter provides distinction of 209 different teaching goals which are connected to methods. In Competence Developing Games (CDGs - serious games to convey knowledge) and in IT security education, a two- or three level typology exists, reducing possible learning outcomes to awareness, training, and education. This study explores whether this much simpler framework succeeds in achieving the same range of learning outcomes. Method wise a keyword analysis was conducted. The results were threefold: 1. The words used to describe teaching goals in CDGs on IT security education do not reflect the whole range of learning outcomes. 2. The word choice is nevertheless different from common language, indicating an intentional use of language. 3. IT security CDGs use different sets of terms to describe learning outcomes, depending on whether they are awareness, training, or education games. The interpretation of the findings is that the reduction to just three types of CDGs reduces the capacity to communicate and think about learning outcomes and consequently reduces the outcomes that are intentionally achieved.},
  language  = {en}
}