@article{FiedlerOrzadaFloeseretal.2022,
  author    = {Fiedler, Thomas M. and Orzada, Stephan and Fl{\"o}ser, Martina and Rietsch, Stefan H. G. and Schmidt, Simon and Stelter, Jonathan K. and Wittrich, Marco and Quick, Harald H. and Bitz, Andreas and Ladd, Mark E.},
  title     = {Performance and safety assessment of an integrated transmit array for body imaging at 7 T under consideration of specificabsorption rate, tissue temperature, and thermal dose},
  series = {NMR in Biomedicine},
  volume    = {35},
  journal   = {NMR in Biomedicine},
  number    = {5},
  publisher = {Wiley},
  issn      = {0952-3480 (Print)},
  doi       = {10.1002/nbm.4656},
  pages     = {1 -- 17},
  year      = {2022},
  abstract  = {In this study, the performance of an integrated body-imaging array for 7 T with 32 radiofrequency (RF) channels under consideration of local specific absorption rate (SAR), tissue temperature, and thermal dose limits was evaluated and the imaging performance was compared with a clinical 3 T body coil. Thirty-two transmit elements were placed in three rings between the bore liner and RF shield of the gradient coil. Slice-selective RF pulse optimizations for B1 shimming and spokes were performed for differently oriented slices in the body under consideration of realistic constraints for power and local SAR. To improve the B1+ homogeneity, safety assessments based on temperature and thermal dose were performed to possibly allow for higher input power for the pulse optimization than permissible with SAR limits. The results showed that using two spokes, the 7 T array outperformed the 3 T birdcage in all the considered regions of interest. However, a significantly higher SAR or lower duty cycle at 7 T is necessary in some cases to achieve similar B1+ homogeneity as at 3 T. The homogeneity in up to 50 cm-long coronal slices can particularly benefit from the high RF shim performance provided by the 32 RF channels. The thermal dose approach increases the allowable input power and the corresponding local SAR, in one example up to 100 W/kg, without limiting the exposure time necessary for an MR examination. In conclusion, the integrated antenna array at 7 T enables a clinical workflow for body imaging and comparable imaging performance to a conventional 3 T clinical body coil.},
  language  = {en}
}
@article{FunkeBeckmann2022,
  author    = {Funke, Harald and Beckmann, Nils},
  title     = {Flexible fuel operation of a Dry-Low-NOx Micromix Combustor with Variable Hydrogen Methane Mixture},
  series = {International Journal of Gas Turbine, Propulsion and Power Systems},
  volume    = {13},
  journal   = {International Journal of Gas Turbine, Propulsion and Power Systems},
  number    = {2},
  issn      = {1882-5079},
  pages     = {1 -- 7},
  year      = {2022},
  abstract  = {The role of hydrogen (H2) as a carbon-free energy carrier is discussed since decades for reducing greenhouse gas emissions. As bridge technology towards a hydrogen-based energy supply, fuel mixtures of natural gas or methane (CH4) and hydrogen are possible. The paper presents the first test results of a low-emission Micromix combustor designed for flexible-fuel operation with variable H2/CH4 mixtures. The numerical and experimental approach for considering variable fuel mixtures instead of recently investigated pure hydrogen is described. In the experimental studies, a first generation FuelFlex Micromix combustor geometry is tested at atmospheric pressure at gas turbine operating conditions corresponding to part- and full-load. The H2/CH4 fuel mixture composition is varied between 57 and 100 vol.\% hydrogen content. Despite the challenges flexible-fuel operation poses onto the design of a combustion system, the evaluated FuelFlex Micromix prototype shows a significant low NOx performance},
  language  = {en}
}
@article{FunkeEschRoosen2022,
  author    = {Funke, Harald and Esch, Thomas and Roosen, Petra},
  title     = {Powertrain Adaptions for LPG Usage in General Aviation},
  series = {MTZ worldwide},
  volume    = {2022},
  journal   = {MTZ worldwide},
  number    = {83},
  publisher = {Springer Nature},
  address   = {Basel},
  doi       = {10.1007/s38313-021-0756-6},
  pages     = {58 -- 62},
  year      = {2022},
  abstract  = {In general aviation, too, it is desirable to be able to operate existing internal combustion engines with fuels that produce less CO₂ than Avgas 100LL being widely used today It can be assumed that, in comparison, the fuels CNG, LPG or LNG, which are gaseous under normal conditions, produce significantly lower emissions. Necessary propulsion system adaptations were investigated as part of a research project at Aachen University of Applied Sciences.},
  language  = {en}
}
@inproceedings{Gaigall2022,
  author    = {Gaigall, Daniel},
  title     = {On Consistent Hypothesis Testing In General Hilbert Spaces},
  series = {Proceedings of the 4th International Conference on Statistics: Theory and Applications (ICSTA'22)},
  booktitle = {Proceedings of the 4th International Conference on Statistics: Theory and Applications (ICSTA'22)},
  publisher = {Avestia Publishing},
  address   = {Orl{\´e}ans, Kanada},
  doi       = {10.11159/icsta22.157},
  pages     = {Paper No. 157},
  year      = {2022},
  abstract  = {Inference on the basis of high-dimensional and functional data are two topics which are discussed frequently in the current statistical literature. A possibility to include both topics in a single approach is working on a very general space for the underlying observations, such as a separable Hilbert space. We propose a general method for consistently hypothesis testing on the basis of random variables with values in separable Hilbert spaces. We avoid concerns with the curse of dimensionality due to a projection idea. We apply well-known test statistics from nonparametric inference to the projected data and integrate over all projections from a specific set and with respect to suitable probability measures. In contrast to classical methods, which are applicable for real-valued random variables or random vectors of dimensions lower than the sample size, the tests can be applied to random vectors of dimensions larger than the sample size or even to functional and high-dimensional data. In general, resampling procedures such as bootstrap or permutation are suitable to determine critical values. The idea can be extended to the case of incomplete observations. Moreover, we develop an efficient algorithm for implementing the method. Examples are given for testing goodness-of-fit in a one-sample situation in [1] or for testing marginal homogeneity on the basis of a paired sample in [2]. Here, the test statistics in use can be seen as generalizations of the well-known Cram{\´e}rvon-Mises test statistics in the one-sample and two-samples case. The treatment of other testing problems is possible as well. By using the theory of U-statistics, for instance, asymptotic null distributions of the test statistics are obtained as the sample size tends to infinity. Standard continuity assumptions ensure the asymptotic exactness of the tests under the null hypothesis and that the tests detect any alternative in the limit. Simulation studies demonstrate size and power of the tests in the finite sample case, confirm the theoretical findings, and are used for the comparison with concurring procedures. A possible application of the general approach is inference for stock market returns, also in high data frequencies. In the field of empirical finance, statistical inference of stock market prices usually takes place on the basis of related log-returns as data. In the classical models for stock prices, i.e., the exponential L{\´e}vy model, Black-Scholes model, and Merton model, properties such as independence and stationarity of the increments ensure an independent and identically structure of the data. Specific trends during certain periods of the stock price processes can cause complications in this regard. In fact, our approach can compensate those effects by the treatment of the log-returns as random vectors or even as functional data.},
  language  = {en}
}
@article{GaigallGerstenbergTrinh2022,
  author    = {Gaigall, Daniel and Gerstenberg, Julian and Trinh, Thi Thu Ha},
  title     = {Empirical process of concomitants for partly categorial data and applications in statistics},
  series = {Bernoulli},
  volume    = {28},
  journal   = {Bernoulli},
  number    = {2},
  publisher = {International Statistical Institute},
  address   = {Den Haag, NL},
  issn      = {1573-9759},
  doi       = {10.3150/21-BEJ1367},
  pages     = {803 -- 829},
  year      = {2022},
  abstract  = {On the basis of independent and identically distributed bivariate random vectors, where the components are categorial and continuous variables, respectively, the related concomitants, also called induced order statistic, are considered. The main theoretical result is a functional central limit theorem for the empirical process of the concomitants in a triangular array setting. A natural application is hypothesis testing. An independence test and a two-sample test are investigated in detail. The fairly general setting enables limit results under local alternatives and bootstrap samples. For the comparison with existing tests from the literature simulation studies are conducted. The empirical results obtained confirm the theoretical findings.},
  language  = {en}
}
@inproceedings{GedleSchmitzGielenetal.2022,
  author    = {Gedle, Yibekal and Schmitz, Mark and Gielen, Hans and Schmitz, Pascal and Herrmann, Ulf and Teixeira Boura, Cristiano Jos{\´e} and Mahdi, Zahra and Chico Caminos, Ricardo Alexander and Dersch, J{\"u}rgen},
  title     = {Analysis of an integrated CSP-PV hybrid power plant},
  series = {SOLARPACES 2020},
  booktitle = {SOLARPACES 2020},
  number    = {2445 / 1},
  publisher = {AIP conference proceedings / American Institute of Physics},
  address   = {Melville, NY},
  isbn      = {978-0-7354-4195-8},
  issn      = {1551-7616 (online)},
  doi       = {10.1063/5.0086236},
  pages     = {9 Seiten},
  year      = {2022},
  abstract  = {In the past, CSP and PV have been seen as competing technologies. Despite massive reductions in the electricity generation costs of CSP plants, PV power generation is - at least during sunshine hours - significantly cheaper. If electricity is required not only during the daytime, but around the clock, CSP with its inherent thermal energy storage gets an advantage in terms of LEC. There are a few examples of projects in which CSP plants and PV plants have been co-located, meaning that they feed into the same grid connection point and ideally optimize their operation strategy to yield an overall benefit. In the past eight years, TSK Flagsol has developed a plant concept, which merges both solar technologies into one highly Integrated CSP-PV-Hybrid (ICPH) power plant. Here, unlike in simply co-located concepts, as analyzed e.g. in [1] - [4], excess PV power that would have to be dumped is used in electric molten salt heaters to increase the storage temperature, improving storage and conversion efficiency. The authors demonstrate the electricity cost sensitivity to subsystem sizing for various market scenarios, and compare the resulting optimized ICPH plants with co-located hybrid plants. Independent of the three feed-in tariffs that have been assumed, the ICPH plant shows an electricity cost advantage of almost 20\% while maintaining a high degree of flexibility in power dispatch as it is characteristic for CSP power plants. As all components of such an innovative concept are well proven, the system is ready for commercial market implementation. A first project is already contracted and in early engineering execution.},
  language  = {en}
}
@incollection{GkatzogiasVeljkovivPohorylesetal.2022,
  author    = {Gkatzogias, Konstantinos and Veljkoviv, Ana and Pohoryles, Daniel A. and Tsionis, Georgios and Bournas, Dionysios A. and Crowley, Helen and Norl{\´e}n, Hedvig and Butenweg, Christoph and Gervasio, Helena and Manfredi, Vincenzo and Masi, Angelo and Zaharieva, Roumiana},
  title     = {Policy practice and regional impact assessment for building renovation},
  series = {REEBUILD Integrated Techniques for the Seismic Strengthening \& Energy Efficiency of Existing Buildings},
  booktitle = {REEBUILD Integrated Techniques for the Seismic Strengthening \& Energy Efficiency of Existing Buildings},
  editor    = {Gkatzogias, Konstantinos and Tsionis, Georgios},
  publisher = {Publications Office of the European Union},
  address   = {Luxembourg},
  isbn      = {978-92-76-60454-9},
  issn      = {1831-9424},
  doi       = {10.2760/883122},
  pages     = {1 -- 68},
  year      = {2022},
  abstract  = {The work presented in this report provides scientific support to building renovation policies in the EU by promoting a holistic point of view on the topic. Integrated renovation can be seen as a nexus between European policies on disaster resilience, energy efficiency and circularity in the building sector. An overview of policy measures for the seismic and energy upgrading of buildings across EU Member States identified only a few available measures for combined upgrading. Regulatory framework, financial instruments and digital tools similar to those for energy renovation, together with awareness and training may promote integrated renovation. A framework for regional prioritisation of building renovation was put forward, considering seismic risk, energy efficiency, and socioeconomic vulnerability independently and in an integrated way. Results indicate that prioritisation of building renovation is a multidimensional problem. Depending on priorities, different integrated indicators should be used to inform policies and accomplish the highest relative or most spread impact across different sectors. The framework was further extended to assess the impact of renovation scenarios across the EU with a focus on priority regions. Integrated renovation can provide a risk-proofed, sustainable, and inclusive built environment, presenting an economic benefit in the order of magnitude of the highest benefit among the separate interventions. Furthermore, it presents the unique capability of reducing fatalities and energy consumption at the same time and, depending on the scenario, to a greater extent.},
  language  = {en}
}
@article{HaegerBongaertsSiegert2022,
  author    = {Haeger, Gerrit and Bongaerts, Johannes and Siegert, Petra},
  title     = {A convenient ninhydrin assay in 96-well format for amino acid-releasing enzymes using an air-stable reagent},
  series = {Analytical Biochemistry},
  journal   = {Analytical Biochemistry},
  number    = {624},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1096-0309},
  doi       = {10.1016/j.ab.2022.114819},
  pages     = {Artikel 114819},
  year      = {2022},
  abstract  = {An improved and convenient ninhydrin assay for aminoacylase activity measurements was developed using the commercial EZ Nin™ reagent. Alternative reagents from literature were also evaluated and compared. The addition of DMSO to the reagent enhanced the solubility of Ruhemann's purple (RP). Furthermore, we found that the use of a basic, aqueous buffer enhances stability of RP. An acidic protocol for the quantification of lysine was developed by addition of glacial acetic acid. The assay allows for parallel processing in a 96-well format with measurements microtiter plates.},
  language  = {en}
}
@article{HarrisKleefeld2022,
  author    = {Harris, Isaac and Kleefeld, Andreas},
  title     = {Analysis and computation of the transmission eigenvalues with a conductive boundary condition},
  series = {Applicable Analysis},
  volume    = {101},
  journal   = {Applicable Analysis},
  number    = {6},
  publisher = {Taylor \& Francis},
  address   = {London},
  issn      = {1563-504X},
  doi       = {10.1080/00036811.2020.1789598},
  pages     = {1880 -- 1895},
  year      = {2022},
  abstract  = {We provide a new analytical and computational study of the transmission eigenvalues with a conductive boundary condition. These eigenvalues are derived from the scalar inverse scattering problem for an inhomogeneous material with a conductive boundary condition. The goal is to study how these eigenvalues depend on the material parameters in order to estimate the refractive index. The analytical questions we study are: deriving Faber-Krahn type lower bounds, the discreteness and limiting behavior of the transmission eigenvalues as the conductivity tends to infinity for a sign changing contrast. We also provide a numerical study of a new boundary integral equation for computing the eigenvalues. Lastly, using the limiting behavior we will numerically estimate the refractive index from the eigenvalues provided the conductivity is sufficiently large but unknown.},
  language  = {en}
}
@article{HeinEubanksLingametal.2022,
  author    = {Hein, Andreas M. and Eubanks, T. Marshall and Lingam, Manasvi and Hibberd, Adam and Fries, Dan and Schneider, Jean and Kervella, Pierre and Kennedy, Robert and Perakis, Nikolaos and Dachwald, Bernd},
  title     = {Interstellar now! Missions to explore nearby interstellar objects},
  series = {Advances in Space Research},
  volume    = {69},
  journal   = {Advances in Space Research},
  number    = {1},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0273-1177},
  doi       = {10.1016/j.asr.2021.06.052},
  pages     = {402 -- 414},
  year      = {2022},
  abstract  = {The recently discovered first hyperbolic objects passing through the Solar System, 1I/'Oumuamua and 2I/Borisov, have raised the question about near term missions to Interstellar Objects. In situ spacecraft exploration of these objects will allow the direct determination of both their structure and their chemical and isotopic composition, enabling an entirely new way of studying small bodies from outside our solar system. In this paper, we map various Interstellar Object classes to mission types, demonstrating that missions to a range of Interstellar Object classes are feasible, using existing or near-term technology. We describe flyby, rendezvous and sample return missions to interstellar objects, showing various ways to explore these bodies characterizing their surface, dynamics, structure and composition. Their direct exploration will constrain their formation and history, situating them within the dynamical and chemical evolution of the Galaxy. These mission types also provide the opportunity to explore solar system bodies and perform measurements in the far outer solar system.},
  language  = {en}
}
@article{HerssensCowburnAlbrachtetal.2022,
  author    = {Herssens, Nolan and Cowburn, James and Albracht, Kirsten and Braunstein, Bjoern and Cazzola, Dario and Colyer, Steffi and Minetti, Alberto E. and Pavei, Gaspare and Rittweger, J{\"o}rn and Weber, Tobias and Green, David A.},
  title     = {Movement in low gravity environments (MoLo) programme - the MoLo-L.O.O.P. study protocol},
  series = {PLOS ONE / Public Library of Science},
  volume    = {17},
  journal   = {PLOS ONE / Public Library of Science},
  number    = {11},
  editor    = {Cattaneo, Luigi},
  publisher = {Plos},
  address   = {San Francisco},
  issn      = {1932-6203},
  doi       = {10.1371/journal.pone.0278051},
  pages     = {e0278051},
  year      = {2022},
  abstract  = {Exposure to prolonged periods in microgravity is associated with deconditioning of the musculoskeletal system due to chronic changes in mechanical stimulation. Given astronauts will operate on the Lunar surface for extended periods of time, it is critical to quantify both external (e.g., ground reaction forces) and internal (e.g., joint reaction forces) loads of relevant movements performed during Lunar missions. Such knowledge is key to predict musculoskeletal deconditioning and determine appropriate exercise countermeasures associated with extended exposure to hypogravity.},
  language  = {en}
}
@article{HeuermannEmmrichBongartz2022,
  author    = {Heuermann, Holger and Emmrich, Thomas and Bongartz, Simon},
  title     = {Microwave spark plug to support ignitions with high compression ratios},
  series = {IEEE Transactions on Plasma Science},
  journal   = {IEEE Transactions on Plasma Science},
  number    = {Early Access},
  publisher = {IEEE},
  issn      = {1939-9375},
  doi       = {10.1109/TPS.2022.3183690},
  pages     = {1 -- 6},
  year      = {2022},
  abstract  = {Upcoming gasoline engines should run with a larger number of fuels beginning from petrol over methanol up to gas by a wide range of compression ratios and a homogeneous charge. In this article, the microwave (MW) spark plug, based on a high-speed frequency hopping system, is introduced as a solution, which can support a nitrogen compression ratio up to 1:39 in a chamber and more. First, an overview of the high-speed frequency hopping MW ignition and operation system as well as the large number of applications are presented. Both gives an understanding of this new base technology for MW plasma generation. Focus of the theoretical part is the explanation of the internal construction of the spark plug, on the achievable of the high voltage generation as well as the high efficiency to hold the plasma. In detail, the development process starting with circuit simulations and ending with the numerical multiphysics field simulations is described. The concept is evaluated with a reference prototype covering the frequency range between 2.40 and 2.48 GHz and working over a large power range from 20 to 200 W. A larger number of different measurements starting by vector hot-S11 measurements and ending by combined working scenarios out of hot temperature, high pressure and charge motion are winding up the article. The limits for the successful pressure tests were given by the pressure chamber. Pressures ranged from 1 to 39 bar and charge motion up to 25 m/s as well as temperatures from 30◦ to 125◦.},
  language  = {en}
}
@incollection{HinkeVervierBrauneretal.2022,
  author    = {Hinke, Christian and Vervier, Luisa and Brauner, Philipp and Schneider, Sebastian and Steuer-Dankert, Linda and Ziefle, Martina and Leicht-Scholten, Carmen},
  title     = {Capability configuration in next generation manufacturing},
  series = {Forecasting next generation manufacturing : digital shadows, human-machine collaboration, and data-driven business models},
  booktitle = {Forecasting next generation manufacturing : digital shadows, human-machine collaboration, and data-driven business models},
  publisher = {Springer},
  address   = {Cham},
  isbn      = {978-3-031-07733-3},
  doi       = {10.1007/978-3-031-07734-0_6},
  pages     = {95 -- 106},
  year      = {2022},
  abstract  = {Industrial production systems are facing radical change in multiple dimensions. This change is caused by technological developments and the digital transformation of production, as well as the call for political and social change to facilitate a transformation toward sustainability. These changes affect both the capabilities of production systems and companies and the design of higher education and educational programs. Given the high uncertainty in the likelihood of occurrence and the technical, economic, and societal impacts of these concepts, we conducted a technology foresight study, in the form of a real-time Delphi analysis, to derive reliable future scenarios featuring the next generation of manufacturing systems. This chapter presents the capabilities dimension and describes each projection in detail, offering current case study examples and discussing related research, as well as implications for policy makers and firms. Specifically, we discuss the benefits of capturing expert knowledge and making it accessible to newcomers, especially in highly specialized industries. The experts argue that in order to cope with the challenges and circumstances of today's world, students must already during their education at university learn how to work with AI and other technologies. This means that study programs must change and that universities must adapt their structural aspects to meet the needs of the students.},
  language  = {en}
}
@article{HoffmannRohrbachUhletal.2022,
  author    = {Hoffmann, Andreas and Rohrbach, Felix and Uhl, Matthias and Ceblin, Maximilian and Bauer, Thomas and Mallah, Marcel and Jacob, Timo and Heuermann, Holger and Kuehne, Alexander J. C.},
  title     = {Atmospheric pressure plasma-jet treatment of polyacrylonitrile-nonwovens—Stabilization and roll-to-roll processing},
  series = {Journal of Applied Polymer Science},
  volume    = {139},
  journal   = {Journal of Applied Polymer Science},
  number    = {37},
  publisher = {Wiley},
  issn      = {0021-8995 (Print)},
  doi       = {10.1002/app.52887},
  pages     = {1 -- 9},
  year      = {2022},
  abstract  = {Carbon nanofiber nonwovens represent a powerful class of materials with prospective application in filtration technology or as electrodes with high surface area in batteries, fuel cells, and supercapacitors. While new precursor-to-carbon conversion processes have been explored to overcome productivity restrictions for carbon fiber tows, alternatives for the two-step thermal conversion of polyacrylonitrile precursors into carbon fiber nonwovens are absent. In this work, we develop a continuous roll-to-roll stabilization process using an atmospheric pressure microwave plasma jet. We explore the influence of various plasma-jet parameters on the morphology of the nonwoven and compare the stabilized nonwoven to thermally stabilized samples using scanning electron microscopy, differential scanning calorimetry, and infrared spectroscopy. We show that stabilization with a non-equilibrium plasma-jet can be twice as productive as the conventional thermal stabilization in a convection furnace, while producing electrodes of comparable electrochemical performance.},
  language  = {en}
}
@article{HoffmannUhlCeblinetal.2022,
  author    = {Hoffmann, Andreas and Uhl, Matthias and Ceblin, Maximilian and Rohrbach, Felix and Bansmann, Joachim and Mallah, Marcel and Heuermann, Holger and Jacob, Timo and Kuehne, Alexander J.C.},
  title     = {Atmospheric pressure plasma-jet treatment of PAN-nonwovens—carbonization of nanofiber electrodes},
  series = {C - Journal of Carbon Research},
  volume    = {8},
  journal   = {C - Journal of Carbon Research},
  number    = {3},
  publisher = {MDPI},
  address   = {Basel},
  issn      = {2311-5629},
  doi       = {10.3390/c8030033},
  pages     = {8 Seiten},
  year      = {2022},
  abstract  = {Carbon nanofibers are produced from dielectric polymer precursors such as polyacrylonitrile (PAN). Carbonized nanofiber nonwovens show high surface area and good electrical conductivity, rendering these fiber materials interesting for application as electrodes in batteries, fuel cells, and supercapacitors. However, thermal processing is slow and costly, which is why new processing techniques have been explored for carbon fiber tows. Alternatives for the conversion of PAN-precursors into carbon fiber nonwovens are scarce. Here, we utilize an atmospheric pressure plasma jet to conduct carbonization of stabilized PAN nanofiber nonwovens. We explore the influence of various processing parameters on the conductivity and degree of carbonization of the converted nanofiber material. The precursor fibers are converted by plasma-jet treatment to carbon fiber nonwovens within seconds, by which they develop a rough surface making subsequent surface activation processes obsolete. The resulting carbon nanofiber nonwovens are applied as supercapacitor electrodes and examined by cyclic voltammetry and impedance spectroscopy. Nonwovens that are carbonized within 60 s show capacitances of up to 5 F g⁻¹.},
  language  = {en}
}
@incollection{HoffschmidtAlexopoulosGoettscheetal.2022,
  author    = {Hoffschmidt, Bernhard and Alexopoulos, Spiros and G{\"o}ttsche, Joachim and Sauerborn, Markus and Kaufhold, O.},
  title     = {High Concentration Solar Collectors},
  series = {Comprehensive Renewable Energy (Second Edition) / Volume 3: Solar Thermal Systems: Components and Applications},
  booktitle = {Comprehensive Renewable Energy (Second Edition) / Volume 3: Solar Thermal Systems: Components and Applications},
  publisher = {Elsevier},
  address   = {Amsterdam},
  isbn      = {978-0-12-819734-9},
  doi       = {10.1016/B978-0-12-819727-1.00058-3},
  pages     = {198 -- 245},
  year      = {2022},
  abstract  = {Solar thermal concentrated power is an emerging technology that provides clean electricity for the growing energy market. To the solar thermal concentrated power plant systems belong the parabolic trough, the Fresnel collector, the solar dish, and the central receiver system. For high-concentration solar collector systems, optical and thermal analysis is essential. There exist a number of measurement techniques and systems for the optical and thermal characterization of the efficiency of solar thermal concentrated systems. For each system, structure, components, and specific characteristics types are described. The chapter presents additionally an outline for the calculation of system performance and operation and maintenance topics. One main focus is set to the models of components and their construction details as well as different types on the market. In the later part of this article, different criteria for the choice of technology are analyzed in detail.},
  language  = {en}
}
@incollection{HoffschmidtAlexopoulosRauetal.2022,
  author    = {Hoffschmidt, Bernhard and Alexopoulos, Spiros and Rau, Christoph and Sattler, Johannes Christoph and Anthrakidis, Anette and Teixeira Boura, Cristiano Jos{\´e} and O'Connor, B. and Chico Caminos, Ricardo Alexander and Rend{\´o}n, C. and Hilger, P.},
  title     = {Concentrating solar power},
  series = {Comprehensive Renewable Energy (Second Edition) / Volume 3: Solar Thermal Systems: Components and Applications},
  booktitle = {Comprehensive Renewable Energy (Second Edition) / Volume 3: Solar Thermal Systems: Components and Applications},
  publisher = {Elsevier},
  address   = {Amsterdam},
  isbn      = {978-0-12-819734-9},
  pages     = {670 -- 724},
  year      = {2022},
  abstract  = {The focus of this chapter is the production of power and the use of the heat produced from concentrated solar thermal power (CSP) systems. The chapter starts with the general theoretical principles of concentrating systems including the description of the concentration ratio, the energy and mass balance. The power conversion systems is the main part where solar-only operation and the increase in operational hours. Solar-only operation include the use of steam turbines, gas turbines, organic Rankine cycles and solar dishes. The operational hours can be increased with hybridization and with storage. Another important topic is the cogeneration where solar cooling, desalination and of heat usage is described. Many examples of commercial CSP power plants as well as research facilities from the past as well as current installed and in operation are described in detail. The chapter closes with economic and environmental aspects and with the future potential of the development of CSP around the world.},
  language  = {en}
}
@inproceedings{HorikawaAshikagaYamaguchietal.2022,
  author    = {Horikawa, Atsushi and Ashikaga, Mitsugu and Yamaguchi, Masato and Ogino, Tomoyuki and Aoki, Shigeki and Wirsum, Manfred and Funke, Harald and Kusterer, Karsten},
  title     = {Combined heat and power supply demonstration of Micro-Mix Hydrogen Combustion Applied to M1A-17 Gas Turbine},
  series = {Proceedings of ASME Turbo Expo 2022: Turbomachinery Technical Conference and Exposition (GT2022) (Volume 3A)},
  booktitle = {Proceedings of ASME Turbo Expo 2022: Turbomachinery Technical Conference and Exposition (GT2022) (Volume 3A)},
  publisher = {American Society of Mechanical Engineers},
  address   = {Fairfield},
  isbn      = {978-0-7918-8599-4},
  doi       = {10.1115/GT2022-81620},
  pages     = {7 Seiten},
  year      = {2022},
  abstract  = {Kawasaki Heavy Industries, Ltd. (KHI), Aachen University of Applied Sciences, and B\&B-AGEMA GmbH have investigated the potential of low NOx micro-mix (MMX) hydrogen combustion and its application to an industrial gas turbine combustor. Engine demonstration tests of a MMX combustor for the M1A-17 gas turbine with a co-generation system were conducted in the hydrogen-fueled power generation plant in Kobe City, Japan. This paper presents the results of the commissioning test and the combined heat and power (CHP) supply demonstration. In the commissioning test, grid interconnection, loading tests and load cut-off tests were successfully conducted. All measurement results satisfied the Japanese environmental regulation values. Dust and soot as well as SOx were not detected. The NOx emissions were below 84 ppmv at 15 \% O2. The noise level at the site boundary was below 60 dB. The vibration at the site boundary was below 45 dB. During the combined heat and power supply demonstration, heat and power were supplied to neighboring public facilities with the MMX combustion technology and 100 \% hydrogen fuel. The electric power output reached 1800 kW at which the NOx emissions were 72 ppmv at 15 \% O2, and 60 \%RH. Combustion instabilities were not observed. The gas turbine efficiency was improved by about 1 \% compared to a non-premixed type combustor with water injection as NOx reduction method. During a total equivalent operation time of 1040 hours, all combustor parts, the M1A-17 gas turbine as such, and the co-generation system were without any issues.},
  language  = {en}
}
@article{KahmannRauschPluemeretal.2022,
  author    = {Kahmann, Stephanie L. and Rausch, Valentin and Pl{\"u}mer, Jonathan and M{\"u}ller, Lars P. and Pieper, Martin and Wegmann, Kilian},
  title     = {The automized fracture edge detection and generation of three-dimensional fracture probability heat maps},
  series = {Medical Engineering \& Physics},
  volume    = {2022},
  journal   = {Medical Engineering \& Physics},
  number    = {110},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1350-4533},
  pages     = {7 Seiten},
  year      = {2022},
  abstract  = {With proven impact of statistical fracture analysis on fracture classifications, it is desirable to minimize the manual work and to maximize repeatability of this approach. We address this with an algorithm that reduces the manual effort to segmentation, fragment identification and reduction. The fracture edge detection and heat map generation are performed automatically. With the same input, the algorithm always delivers the same output. The tool transforms one intact template consecutively onto each fractured specimen by linear least square optimization, detects the fragment edges in the template and then superimposes them to generate a fracture probability heat map. We hypothesized that the algorithm runs faster than the manual evaluation and with low (< 5 mm) deviation. We tested the hypothesis in 10 fractured proximal humeri and found that it performs with good accuracy (2.5 mm ± 2.4 mm averaged Euclidean distance) and speed (23 times faster). When applied to a distal humerus, a tibia plateau, and a scaphoid fracture, the run times were low (1-2 min), and the detected edges correct by visual judgement. In the geometrically complex acetabulum, at a run time of 78 min some outliers were considered acceptable. An automatically generated fracture probability heat map based on 50 proximal humerus fractures matches the areas of high risk of fracture reported in medical literature. Such automation of the fracture analysis method is advantageous and could be extended to reduce the manual effort even further.},
  language  = {en}
}
@article{KaulenSchwabedalSchneideretal.2022,
  author    = {Kaulen, Lars and Schwabedal, Justus T. C. and Schneider, Jules and Ritter, Philipp and Bialonski, Stephan},
  title     = {Advanced sleep spindle identification with neural networks},
  series = {Scientific Reports},
  volume    = {12},
  journal   = {Scientific Reports},
  number    = {Article number: 7686},
  publisher = {Springer Nature},
  address   = {London},
  issn      = {2045-2322},
  doi       = {10.1038/s41598-022-11210-y},
  pages     = {1 -- 10},
  year      = {2022},
  abstract  = {Sleep spindles are neurophysiological phenomena that appear to be linked to memory formation and other functions of the central nervous system, and that can be observed in electroencephalographic recordings (EEG) during sleep. Manually identified spindle annotations in EEG recordings suffer from substantial intra- and inter-rater variability, even if raters have been highly trained, which reduces the reliability of spindle measures as a research and diagnostic tool. The Massive Online Data Annotation (MODA) project has recently addressed this problem by forming a consensus from multiple such rating experts, thus providing a corpus of spindle annotations of enhanced quality. Based on this dataset, we present a U-Net-type deep neural network model to automatically detect sleep spindles. Our model's performance exceeds that of the state-of-the-art detector and of most experts in the MODA dataset. We observed improved detection accuracy in subjects of all ages, including older individuals whose spindles are particularly challenging to detect reliably. Our results underline the potential of automated methods to do repetitive cumbersome tasks with super-human performance.},
  language  = {en}
}
@misc{KeimerGirbigMayntzetal.2022,
  author    = {Keimer, Jona and Girbig, Leo and Mayntz, Joscha and Tegtmeyer, Philipp and Wendland, Frederik and Dahman, Peter and Fisher, Alex and Dorrington, Graham},
  title     = {Flight mission optimization for eco-efficiency in consideration of electric regeneration and atmospheric conditions},
  series = {AIAA AVIATION 2022 Forum},
  journal   = {AIAA AVIATION 2022 Forum},
  publisher = {AIAA},
  address   = {Reston, Va.},
  doi       = {10.2514/6.2022-4118},
  year      = {2022},
  abstract  = {The development and operation of hybrid or purely electrically powered aircraft in regional air mobility is a significant challenge for the entire aviation sector. This technology is expected to lead to substantial advances in flight performance, energy efficiency, reliability, safety, noise reduction, and exhaust emissions. Nevertheless, any consumed energy results in heat or carbon dioxide emissions and limited electric energy storage capabilities suppress commercial use. Therefore, the significant challenges to achieving eco-efficient aviation are increased aircraft efficiency, the development of new energy storage technologies, and the optimization of flight operations. Two major approaches for higher eco-efficiency are identified: The first one, is to take horizontal and vertical atmospheric motion phenomena into account. Where, in particular, atmospheric waves hold exciting potential. The second one is the use of the regeneration ability of electric aircraft. The fusion of both strategies is expected to improve efficiency. The objective is to reduce energy consumption during flight while not neglecting commercial usability and convenient flight characteristics. Therefore, an optimized control problem based on a general aviation class aircraft has to be developed and validated by flight experiments. The formulated approach enables a development of detailed knowledge of the potential and limitations of optimizing flight missions, considering the capability of regeneration and atmospheric influences to increase efficiency and range.},
  language  = {en}
}
@article{KemptFreyerNagel2022,
  author    = {Kempt, Hendrik and Freyer, Nils and Nagel, Saskia K.},
  title     = {Justice and the normative standards of explainability in healthcare},
  series = {Philosophy \& Technology},
  volume    = {35},
  journal   = {Philosophy \& Technology},
  number    = {Article number: 100},
  publisher = {Springer Nature},
  address   = {Berlin},
  doi       = {10.1007/s13347-022-00598-0},
  pages     = {1 -- 19},
  year      = {2022},
  abstract  = {Providing healthcare services frequently involves cognitively demanding tasks, including diagnoses and analyses as well as complex decisions about treatments and therapy. From a global perspective, ethically significant inequalities exist between regions where the expert knowledge required for these tasks is scarce or abundant. One possible strategy to diminish such inequalities and increase healthcare opportunities in expert-scarce settings is to provide healthcare solutions involving digital technologies that do not necessarily require the presence of a human expert, e.g., in the form of artificial intelligent decision-support systems (AI-DSS). Such algorithmic decision-making, however, is mostly developed in resource- and expert-abundant settings to support healthcare experts in their work. As a practical consequence, the normative standards and requirements for such algorithmic decision-making in healthcare require the technology to be at least as explainable as the decisions made by the experts themselves. The goal of providing healthcare in settings where resources and expertise are scarce might come with a normative pull to lower the normative standards of using digital technologies in order to provide at least some healthcare in the first place. We scrutinize this tendency to lower standards in particular settings from a normative perspective, distinguish between different types of absolute and relative, local and global standards of explainability, and conclude by defending an ambitious and practicable standard of local relative explainability.},
  language  = {en}
}
@article{KleefeldZimmermann2022,
  author    = {Kleefeld, Andreas and Zimmermann, M.},
  title     = {Computing Elastic Interior Transmission Eigenvalues},
  series = {Integral Methods in Science and Engineering},
  journal   = {Integral Methods in Science and Engineering},
  editor    = {Constanda, Christian and Bodmann, Bardo E.J. and Harris, Paul J.},
  publisher = {Birkh{\"a}user},
  address   = {Cham},
  isbn      = {978-3-031-07171-3},
  doi       = {10.1007/978-3-031-07171-3_10},
  pages     = {139 -- 155},
  year      = {2022},
  abstract  = {An alternative method is presented to numerically compute interior elastic transmission eigenvalues for various domains in two dimensions. This is achieved by discretizing the resulting system of boundary integral equations in combination with a nonlinear eigenvalue solver. Numerical results are given to show that this new approach can provide better results than the finite element method when dealing with general domains.},
  language  = {en}
}
@article{KotliarOrtnerConradietal.2022,
  author    = {Kotliar, Konstantin and Ortner, Marion and Conradi, Anna and Hacker, Patricia and Hauser, Christine and G{\"u}nthner, Roman and Moser, Michaela and Muggenthaler, Claudia and Diehl-Schmid, Janine and Priller, Josef and Schmaderer, Christoph and Grimmer, Timo},
  title     = {Altered retinal cerebral vessel oscillation frequencies in Alzheimer's disease compatible with impaired amyloid clearance},
  series = {Neurobiology of Aging},
  volume    = {120},
  journal   = {Neurobiology of Aging},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0197-4580},
  doi       = {10.1016/j.neurobiolaging.2022.08.012},
  pages     = {117 -- 127},
  year      = {2022},
  abstract  = {Retinal vessels are similar to cerebral vessels in their structure and function. Moderately low oscillation frequencies of around 0.1 Hz have been reported as the driving force for paravascular drainage in gray matter in mice and are known as the frequencies of lymphatic vessels in humans. We aimed to elucidate whether retinal vessel oscillations are altered in Alzheimer's disease (AD) at the stage of dementia or mild cognitive impairment (MCI). Seventeen patients with mild-to-moderate dementia due to AD (ADD); 23 patients with MCI due to AD, and 18 cognitively healthy controls (HC) were examined using Dynamic Retinal Vessel Analyzer. Oscillatory temporal changes of retinal vessel diameters were evaluated using mathematical signal analysis. Especially at moderately low frequencies around 0.1 Hz, arterial oscillations in ADD and MCI significantly prevailed over HC oscillations and correlated with disease severity. The pronounced retinal arterial vasomotion at moderately low frequencies in the ADD and MCI groups would be compatible with the view of a compensatory upregulation of paravascular drainage in AD and strengthen the amyloid clearance hypothesis.},
  language  = {en}
}
@misc{KrafftKukaUlberetal.2022,
  author    = {Krafft, Simone and Kuka, Katrin and Ulber, Roland and Tippk{\"o}tter, Nils},
  title     = {Utilization of Lolium perenne varieties as a renewable substrate for single-cell proteins, lactate, and composite materials},
  series = {Chemie Ingenieur Technik},
  volume    = {94},
  journal   = {Chemie Ingenieur Technik},
  number    = {9},
  publisher = {Wiley-VCH},
  address   = {Weinheim},
  issn      = {0009-286X},
  doi       = {10.1002/cite.202255306},
  pages     = {1303 -- 1304},
  year      = {2022},
  abstract  = {Lolium perenne (perennial ryegrass) is aproductive and high-quality forage grass indigenous to Southern Europe, temperate Asia, and North Africa. Nowadays it is widespread and the dominant grass species on green areas in temperate climates. This abundant source of biomass is suitable for the development of bioeconomic processes because of its high cellulose and water-soluble carbohydrate content. In this work, novel breeds of the perennial ryegrass are being examined with regards to their quality parameters and biotechnological utilization options within the context of bioeconomy. Three processing operations are presented. In the first process, the perennial ryegrass is pretreated by pressing or hydrothermal extraction to derive glucosevia subsequent enzymatic hydrolysis of cellulose. A yield of up to 82 \% glucose was achieved when using the hydrothermal ex-traction as pretreatment. In a second process, the ryegrass is used to produce lactic acid in high concentrations. The influence of the growth conditions and the cutting time on the carboxylic acid yield is investigated. A yield of lactic acid of above 150 g kg⁻¹ dry matter was achieved. The third process is to use Lolium perenne as a substrate in the fermentation of K. marxianus for the microbial production of single-cell proteins. The perennial ryegrass is screw-pressed and the press juice is used as medium. When supplementing the press juice with yeast media components, a biomass concentration of up to 16 g L⁻¹ could be achieved.},
  language  = {en}
}
@book{Laack2022,
  author    = {Laack, Walter van},
  title     = {Greater Than the Entire Universe},
  publisher = {van Laack GmbH},
  address   = {Aachen},
  isbn      = {978-3-936624-52-6},
  pages     = {120 Seiten},
  year      = {2022},
  language  = {en}
}
@inproceedings{LangohrBungCrookston2022,
  author    = {Langohr, Philipp and Bung, Daniel Bernhard and Crookston, Brian M.},
  title     = {Hybrid investigation of labyrinth weirs: Discharge capacity and energy dissipation},
  series = {Proceedings of the 39th IAHR World Congress},
  booktitle = {Proceedings of the 39th IAHR World Congress},
  editor    = {Ortega-S{\´a}nchez, Miguel},
  publisher = {International Association for Hydro-Environment Engineering and Research (IAHR)},
  address   = {Madrid},
  isbn      = {978-90-832612-1-8},
  issn      = {2521-7119 (print)},
  doi       = {10.3850/IAHR-39WC252171192022738},
  pages     = {2313 -- 2318},
  year      = {2022},
  abstract  = {The replacement of existing spillway crests or gates with labyrinth weirs is a proven techno-economical means to increase the discharge capacity when rehabilitating existing structures. However, additional information is needed regarding energy dissipation of such weirs, since due to the folded weir crest, a three-dimensional flow field is generated, yielding more complex overflow and energy dissipation processes. In this study, CFD simulations of labyrinth weirs were conducted 1) to analyze the discharge coefficients for different discharges to compare the Cd values to literature data and 2) to analyze and improve energy dissipation downstream of the structure. All tests were performed for a structure at laboratory scale with a height of approx. P = 30.5 cm, a ratio of the total crest length to the total width of 4.7, a sidewall angle of 10° and a quarter-round weir crest shape. Tested headwater ratios were 0.089 ≤ HT/P ≤ 0.817. For numerical simulations, FLOW-3D Hydro was employed, solving the RANS equations with use of finite-volume method and RNG k-ε turbulence closure. In terms of discharge capacity, results were compared to data from physical model tests performed at the Utah Water Research Laboratory (Utah State University), emphasizing higher discharge coefficients from CFD than from the physical model. For upstream heads, some discrepancy in the range of ± 1 cm between literature, CFD and physical model tests was identified with a discussion regarding differences included in the manuscript. For downstream energy dissipation, variable tailwater depths were considered to analyze the formation and sweep-out of a hydraulic jump. It was found that even for high discharges, relatively low downstream Froude numbers were obtained due to high energy dissipation involved by the three-dimensional flow between the sidewalls. The effects of some additional energy dissipation devices, e.g. baffle blocks or end sills, were also analyzed. End sills were found to be non-effective. However, baffle blocks with different locations may improve energy dissipation downstream of labyrinth weirs.},
  language  = {en}
}
@article{LenzKahmannBehbahanietal.2022,
  author    = {Lenz, Maximilian and Kahmann, Stephanie Lucina and Behbahani, Mehdi and Pennig, Lenhard and Hackl, Michael and Leschinger, Tim and M{\"u}ller, Lars Peter and Wegmann, Kilian},
  title     = {Influence of rotator cuff preload on fracture configuration in proximal humerus fractures: a proof of concept for fracture simulation},
  series = {Archives of Orthopaedic and Trauma Surgery},
  journal   = {Archives of Orthopaedic and Trauma Surgery},
  publisher = {Springer},
  address   = {Berlin, Heidelberg},
  issn      = {1434-3916},
  doi       = {10.1007/s00402-022-04471-9},
  year      = {2022},
  abstract  = {Introduction In regard of surgical training, the reproducible simulation of life-like proximal humerus fractures in human cadaveric specimens is desirable. The aim of the present study was to develop a technique that allows simulation of realistic proximal humerus fractures and to analyse the influence of rotator cuff preload on the generated lesions in regards of fracture configuration. Materials and methods Ten cadaveric specimens (6 left, 4 right) were fractured using a custom-made drop-test bench, in two groups. Five specimens were fractured without rotator cuff preload, while the other five were fractured with the tendons of the rotator cuff preloaded with 2 kg each. The humeral shaft and the shortened scapula were potted. The humerus was positioned at 90° of abduction and 10° of internal rotation to simulate a fall on the elevated arm. In two specimens of each group, the emergence of the fractures was documented with high-speed video imaging. Pre-fracture radiographs were taken to evaluate the deltoid-tuberosity index as a measure of bone density. Post-fracture X-rays and CT scans were performed to define the exact fracture configurations. Neer's classification was used to analyse the fractures. Results In all ten cadaveric specimens life-like proximal humerus fractures were achieved. Two III-part and three IV-part fractures resulted in each group. The preloading of the rotator cuff muscles had no further influence on the fracture configuration. High-speed videos of the fracture simulation revealed identical fracture mechanisms for both groups. We observed a two-step fracture mechanism, with initial impaction of the head segment against the glenoid followed by fracturing of the head and the tuberosities and then with further impaction of the shaft against the acromion, which lead to separation of the tuberosities. Conclusion A high energetic axial impulse can reliably induce realistic proximal humerus fractures in cadaveric specimens. The preload of the rotator cuff muscles had no influence on initial fracture configuration. Therefore, fracture simulation in the proximal humerus is less elaborate. Using the presented technique, pre-fractured specimens are available for real-life surgical education.},
  language  = {en}
}
@article{LindnerBurgerRutledgeetal.2022,
  author    = {Lindner, Simon and Burger, Ren{\´e} and Rutledge, Douglas N. and Do, Xuan Tung and Rumpf, Jessica and Diehl, Bernd W. K. and Schulze, Margit and Monakhova, Yulia},
  title     = {Is the calibration transfer of multivariate calibration models between high- and low-field NMR instruments possible? A case study of lignin molecular weight},
  series = {Analytical chemistry},
  volume    = {94},
  journal   = {Analytical chemistry},
  number    = {9},
  publisher = {ACS Publications},
  address   = {Washington, DC},
  isbn      = {1520-6882},
  doi       = {10.1021/acs.analchem.1c05125},
  pages     = {3997 -- 4004},
  year      = {2022},
  abstract  = {Although several successful applications of benchtop nuclear magnetic resonance (NMR) spectroscopy in quantitative mixture analysis exist, the possibility of calibration transfer remains mostly unexplored, especially between high- and low-field NMR. This study investigates for the first time the calibration transfer of partial least squares regressions [weight average molecular weight (Mw) of lignin] between high-field (600 MHz) NMR and benchtop NMR devices (43 and 60 MHz). For the transfer, piecewise direct standardization, calibration transfer based on canonical correlation analysis, and transfer via the extreme learning machine auto-encoder method are employed. Despite the immense resolution difference between high-field and low-field NMR instruments, the results demonstrate that the calibration transfer from high- to low-field is feasible in the case of a physical property, namely, the molecular weight, achieving validation errors close to the original calibration (down to only 1.2 times higher root mean square errors). These results introduce new perspectives for applications of benchtop NMR, in which existing calibrations from expensive high-field instruments can be transferred to cheaper benchtop instruments to economize.},
  language  = {en}
}
@inproceedings{MahdiDerschSchmitzetal.2022,
  author    = {Mahdi, Zahra and Dersch, J{\"u}rgen and Schmitz, Pascal and Dieckmann, Simon and Chico Caminos, Ricardo Alexander and Teixeira Boura, Cristiano Jos{\´e} and Herrmann, Ulf and Schwager, Christian and Schmitz, Mark and Gielen, Hans and Gedle, Yibekal and B{\"u}scher, Rauno},
  title     = {Technical assessment of Brayton cycle heat pumps for the integration in hybrid PV-CSP power plants},
  series = {SOLARPACES 2020},
  booktitle = {SOLARPACES 2020},
  number    = {2445 / 1},
  publisher = {AIP conference proceedings / American Institute of Physics},
  address   = {Melville, NY},
  isbn      = {978-0-7354-4195-8},
  issn      = {1551-7616 (online)},
  doi       = {10.1063/5.0086269},
  pages     = {11 Seiten},
  year      = {2022},
  abstract  = {The hybridization of Concentrated Solar Power (CSP) and Photovoltaics (PV) systems is a promising approach to reduce costs of solar power plants, while increasing dispatchability and flexibility of power generation. High temperature heat pumps (HT HP) can be utilized to boost the salt temperature in the thermal energy storage (TES) of a Parabolic Trough Collector (PTC) system from 385 °C up to 565 °C. A PV field can supply the power for the HT HP, thus effectively storing the PV power as thermal energy. Besides cost-efficiently storing energy from the PV field, the power block efficiency of the overall system is improved due to the higher steam parameters. This paper presents a technical assessment of Brayton cycle heat pumps to be integrated in hybrid PV-CSP power plants. As a first step, a theoretical analysis was carried out to find the most suitable working fluid. The analysis included the fluids Air, Argon (Ar), Nitrogen (N2) and Carbon dioxide (CO2). N2 has been chosen as the optimal working fluid for the system. After the selection of the ideal working medium, different concepts for the arrangement of a HT HP in a PV-CSP hybrid power plant were developed and simulated in EBSILON®Professional. The concepts were evaluated technically by comparing the number of components required, pressure losses and coefficient of performance (COP).},
  language  = {en}
}
@article{MalinowskiFournierHorbachetal.2022,
  author    = {Malinowski, Daniel and Fournier, Yvan and Horbach, Andreas and Frick, Michael and Magliani, Mirko and Kalverkamp, Sebastian and Hildinger, Martin and Spillner, Jan and Behbahani, Mehdi and Hima, Flutura},
  title     = {Computational fluid dynamics analysis of endoluminal aortic perfusion},
  series = {Perfusion},
  volume    = {0},
  journal   = {Perfusion},
  number    = {0},
  publisher = {Sage},
  address   = {London},
  issn      = {1477-111X},
  doi       = {10.1177/02676591221099809},
  pages     = {1 -- 8},
  year      = {2022},
  abstract  = {Introduction: In peripheral percutaneous (VA) extracorporeal membrane oxygenation (ECMO) procedures the femoral arteries perfusion route has inherent disadvantages regarding poor upper body perfusion due to watershed. With the advent of new long flexible cannulas an advancement of the tip up to the ascending aorta has become feasible. To investigate the impact of such long endoluminal cannulas on upper body perfusion, a Computational Fluid Dynamics (CFD) study was performed considering different support levels and three cannula positions. Methods: An idealized literature-based- and a real patient proximal aortic geometry including an endoluminal cannula were constructed. The blood flow was considered continuous. Oxygen saturation was set to 80\% for the blood coming from the heart and to 100\% for the blood leaving the cannula. 50\% and 90\% venoarterial support levels from the total blood flow rate of 6 l/min were investigated for three different positions of the cannula in the aortic arch. Results: For both geometries, the placement of the cannula in the ascending aorta led to a superior oxygenation of all aortic blood vessels except for the left coronary artery. Cannula placements at the aortic arch and descending aorta could support supra-aortic arteries, but not the coronary arteries. All positions were able to support all branches with saturated blood at 90\% flow volume. Conclusions: In accordance with clinical observations CFD analysis reveals, that retrograde advancement of a long endoluminal cannula can considerably improve the oxygenation of the upper body and lead to oxygen saturation distributions similar to those of a central cannulation.},
  language  = {en}
}
@article{MandekarHollandThielenetal.2022,
  author    = {Mandekar, Swati and Holland, Abigail and Thielen, Moritz and Behbahani, Mehdi and Melnykowycz, Mark},
  title     = {Advancing towards Ubiquitous EEG, Correlation of In-Ear EEG with Forehead EEG},
  series = {Sensors},
  volume    = {22},
  journal   = {Sensors},
  number    = {4},
  publisher = {MDPI},
  address   = {Basel},
  issn      = {1424-8220},
  doi       = {10.3390/s22041568},
  pages     = {1 -- 19},
  year      = {2022},
  abstract  = {Wearable EEG has gained popularity in recent years driven by promising uses outside of clinics and research. The ubiquitous application of continuous EEG requires unobtrusive form-factors that are easily acceptable by the end-users. In this progression, wearable EEG systems have been moving from full scalp to forehead and recently to the ear. The aim of this study is to demonstrate that emerging ear-EEG provides similar impedance and signal properties as established forehead EEG. EEG data using eyes-open and closed alpha paradigm were acquired from ten healthy subjects using generic earpieces fitted with three custom-made electrodes and a forehead electrode (at Fpx) after impedance analysis. Inter-subject variability in in-ear electrode impedance ranged from 20 kΩ to 25 kΩ at 10 Hz. Signal quality was comparable with an SNR of 6 for in-ear and 8 for forehead electrodes. Alpha attenuation was significant during the eyes-open condition in all in-ear electrodes, and it followed the structure of power spectral density plots of forehead electrodes, with the Pearson correlation coefficient of 0.92 between in-ear locations ELE (Left Ear Superior) and ERE (Right Ear Superior) and forehead locations, Fp1 and Fp2, respectively. The results indicate that in-ear EEG is an unobtrusive alternative in terms of impedance, signal properties and information content to established forehead EEG.},
  language  = {en}
}
@article{MarinkovicButenweg2022,
  author    = {Marinkovic, Marko and Butenweg, Christoph},
  title     = {Numerical analysis of the in-plane behaviour of decoupled masonry infilled RC frames},
  series = {Engineering Structures},
  volume    = {272},
  journal   = {Engineering Structures},
  number    = {1},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0141-0296},
  doi       = {10.1016/j.engstruct.2022.114959},
  pages     = {18 Seiten},
  year      = {2022},
  abstract  = {Damage of reinforced concrete (RC) frames with masonry infill walls has been observed after many earthquakes. Brittle behaviour of the masonry infills in combination with the ductile behaviour of the RC frames makes infill walls prone to damage during earthquakes. Interstory deformations lead to an interaction between the infill and the RC frame, which affects the structural response. The result of this interaction is significant damage to the infill wall and sometimes to the surrounding structural system too. In most design codes, infill walls are considered as non-structural elements and neglected in the design process, because taking into account the infills and considering the interaction between frame and infill in software packages can be complicated and impractical. A good way to avoid negative aspects arising from this behavior is to ensure no or low-interaction of the frame and infill wall, for instance by decoupling the infill from the frame. This paper presents the numerical study performed to investigate new connection system called INODIS (Innovative Decoupled Infill System) for decoupling infill walls from surrounding frame with the aim to postpone infill activation to high interstory drifts thus reducing infill/frame interaction and minimizing damage to both infills and frames. The experimental results are first used for calibration and validation of the numerical model, which is then employed for investigating the influence of the material parameters as well as infill's and frame's geometry on the in-plane behaviour of the infilled frames with the INODIS system. For all the investigated situations, simulation results show significant improvements in behaviour for decoupled infilled RC frames in comparison to the traditionally infilled frames.},
  language  = {en}
}
@article{MarinkovićButenweg2022,
  author    = {Marinković, Marko and Butenweg, Christoph},
  title     = {Experimental testing of decoupled masonry infills with steel anchors for out-of-plane support under combined in-plane and out-of-plane seismic loading},
  series = {Construction and Building Materials},
  volume    = {318},
  journal   = {Construction and Building Materials},
  number    = {1},
  editor    = {Ford, Michael C.},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1879-0526},
  doi       = {10.1016/j.conbuildmat.2021.126041},
  year      = {2022},
  abstract  = {Because of simple construction process, high energy efficiency, significant fire resistance and excellent sound isolation, masonry infilled reinforced concrete (RC) frame structures are very popular in most of the countries in the world, as well as in seismic active areas. However, many RC frame structures with masonry infills were seriously damaged during earthquake events, as the traditional infills are generally constructed with direct contact to the RC frame which brings undesirable infill/frame interaction. This interaction leads to the activation of the equivalent diagonal strut in the infill panel, due to the RC frame deformation, and combined with seismically induced loads perpendicular to the infill panel often causes total collapses of the masonry infills and heavy damages to the RC frames. This fact was the motivation for developing different approaches for improving the behaviour of masonry infills, where infill isolation (decoupling) from the frame has been more intensively studied in the last decade. In-plane isolation of the infill wall reduces infill activation, but causes the need for additional measures to restrain out-of-plane movements. This can be provided by installing steel anchors, as proposed by some researchers. Within the framework of European research project INSYSME (Innovative Systems for Earthquake Resistant Masonry Enclosures in Reinforced Concrete Buildings) the system based on a use of elastomers for in-plane decoupling and steel anchors for out-of-plane restrain was tested. This constructive solution was tested and deeply investigated during the experimental campaign where traditional and decoupled masonry infilled RC frames with anchors were subjected to separate and combined in-plane ‬and out-of-plane loading. Based on a detailed evaluation and comparison of the test results, the performance and effectiveness of the developed system are illustrated.},
  language  = {en}
}
@inproceedings{Maurer2022,
  author    = {Maurer, Florian},
  title     = {Framework to provide a simulative comparison of different energy market designs},
  series = {Energy Informatics},
  volume    = {5},
  booktitle = {Energy Informatics},
  number    = {2, Article number: 12},
  publisher = {Springer Nature},
  issn      = {2520-8942},
  doi       = {10.1186/s42162-022-00215-6},
  pages     = {18 -- 20},
  year      = {2022},
  abstract  = {Useful market simulations are key to the evaluation of diferent market designs existing of multiple market mechanisms or rules. Yet a simulation framework which has a comparison of diferent market mechanisms in mind was not found. The need to create an objective view on different sets of market rules while investigating meaningful agent strategies concludes that such a simulation framework is needed to advance the research on this subject. An overview of diferent existing market simulation models is given which also shows the research gap and the missing capabilities of those systems. Finally, a methodology is outlined how a novel market simulation which can answer the research questions can be developed.},
  language  = {en}
}
@article{Maurischat2022,
  author    = {Maurischat, Andreas},
  title     = {Algebraic independence of the Carlitz period and its hyperderivatives},
  series = {Journal of Number Theory},
  volume    = {240},
  journal   = {Journal of Number Theory},
  publisher = {Elsevier},
  address   = {Orlando, Fla.},
  issn      = {0022-314X},
  doi       = {10.1016/j.jnt.2022.01.006},
  pages     = {145 -- 162},
  year      = {2022},
  language  = {en}
}
@inproceedings{MayntzKeimerDahmannetal.2022,
  author    = {Mayntz, Joscha and Keimer, Jona and Dahmann, Peter and Hille, Sebastian and Stumpf, Eike and Fisher, Alex and Dorrington, Graham},
  title     = {Electrical Drive and Regeneration in General Aviation Flight with Propellers},
  series = {Deutscher Luft- und Raumfahrtkongress 2020},
  booktitle = {Deutscher Luft- und Raumfahrtkongress 2020},
  publisher = {DGLR},
  address   = {Bonn},
  doi       = {10.25967/530100},
  pages     = {8 Seiten},
  year      = {2022},
  abstract  = {Electric flight has the potential for a more sustainable and energy-saving way of aviation compared to fossil fuel aviation. The electric motor can be used as a generator inflight to regenerate energy during descent. Three different approaches to regenerating with electric propeller powertrains are proposed in this paper. The powertrain is to be set up in a wind tunnel to determine the propeller efficiency in both working modes as well as the noise emissions. Furthermore, the planned flight tests are discussed. In preparation for these tests, a yaw stability analysis is performed with the result that the aeroplane is controllable during flight and in the most critical failure case. The paper shows the potential for inflight regeneration and addresses the research gaps in the dual role of electric powertrains for propulsion and regeneration of general aviation aircraft.},
  language  = {en}
}
@inproceedings{MertensBraunerBaieretal.2022,
  author    = {Mertens, Alexander and Brauner, Philipp and Baier, Ralph and Brillowski, Florian and Dammers, Hannah and van Dyck, Marc and Kong, Iris and K{\"o}nigs, Peter and Kordtomeikel, Frauke and Liehner, Gian Luca and P{\"u}tz, Sebastian and Rodermann, Niklas and Schaar, Anne Kathrin and Steuer-Dankert, Linda and Vervier, Luisa and Wlecke, Shari and Gries, Thomas and Leicht-Scholten, Carmen and Nagel, Saskia K. and Piller, Frank T. and Schuh, G{\"u}nther and Ziefle, Martina and Nitsch, Verena},
  title     = {Modelling Human Factors in Cyber Physical Production Systems by the Integration of Human Digital Shadows},
  series = {Modellierung 2022 Satellite Events},
  booktitle = {Modellierung 2022 Satellite Events},
  editor    = {Michael, Judith and Pfeiffer, J{\´e}r{\^o}me and Wortmann, Andreas},
  publisher = {GI Gesellschaft f{\"u}r Informatik},
  address   = {Bonn},
  doi       = {10.18420/modellierung2022ws-018},
  pages     = {147 -- 149},
  year      = {2022},
  abstract  = {The future of industrial manufacturing and production will increasingly manifest in the form of cyber-physical production systems. Here, Digital Shadows will act as mediators between the physical and digital world to model and operationalize the interactions and relationships between different entities in production systems. Until now, the associated concepts have been primarily pursued and implemented from a technocentric perspective, in which human actors play a subordinate role, if they are considered at all. This paper outlines an anthropocentric approach that explicitly considers the characteristics, behavior, and traits and states of human actors in socio-technical production systems. For this purpose, we discuss the potentials and the expected challenges and threats of creating and using Human Digital Shadows in production.},
  language  = {en}
}
@inproceedings{MilijašŠakićMarinkovićetal.2022,
  author    = {Milijaš, Aleksa and Šakić, Bogdan and Marinković, Marko and Butenweg, Christoph and Gams, Matija and Klinkel, Sven},
  title     = {Effects of prior in-plane damage on out-of-plane response of masonry infills with openings},
  series = {The Third European Conference on Earthquake Engineering and Seismology},
  booktitle = {The Third European Conference on Earthquake Engineering and Seismology},
  editor    = {Arion, Cristian and Scupin, Alexandra and Ţigănescu, Alexandru},
  isbn      = {978-973-100-533-1},
  pages     = {2747 -- 2756},
  year      = {2022},
  abstract  = {Masonry infill walls are the most traditional enclosure system that is still widely used in RC frame buildings all over the world, particularly in seismic active regions. Although infill walls are usually neglected in seismic design, during an earthquake event they are subjected to in-plane and out-of-plane forces that can act separately or simultaneously. Since observations of damage to buildings after recent earthquakes showed detrimental effects of in-plane and out-of-plane load interaction on infill walls, the number of studies that focus on influence of in-plane damage on out-of-plane response has significantly increased. However, most of the xperimental campaigns have considered only solid infills and there is a lack of combined in-plane and out-of-plane experimental tests on masonry infills with openings, although windows and doors strongly affect seismic performance. In this paper, two types of experimental tests on infills with window openings are presented. The first is a pure out-of-plane test and the second one is a sequential in-plane and out-of-plane test aimed at investigating the effects of existing in-plane damage on outof-plane response. Additionally, findings from two tests with similar load procedure that were carried out on fully infilled RC frames in the scope of the same project are used for comparison. Test results clearly show that window opening increased vulnerability of infills to combined seismic actions and that prevention of damage in infills with openings is of the utmost importance for seismic safety.},
  language  = {en}
}
@article{MolinnusIkenJohnenetal.2022,
  author    = {Molinnus, Denise and Iken, Heiko and Johnen, Anna Lynn and Richstein, Benjamin and Hellmich, Lena and Poghossian, Arshak and Knoch, Joachim and Sch{\"o}ning, Michael Josef},
  title     = {Miniaturized pH-Sensitive Field-Effect Capacitors with Ultrathin Ta₂O₅ Films Prepared by Atomic Layer Deposition},
  series = {physica status solidi (a) applications and materials science},
  volume    = {219},
  journal   = {physica status solidi (a) applications and materials science},
  number    = {8},
  publisher = {Wiley-VCH},
  address   = {Weinheim},
  issn      = {1862-6319},
  doi       = {10.1002/pssa.202100660},
  pages     = {7 Seiten},
  year      = {2022},
  abstract  = {Miniaturized electrolyte-insulator-semiconductor capacitors (EISCAPs) with ultrathin gate insulators have been studied in terms of their pH-sensitive sensor characteristics: three different EISCAP systems consisting of Al-p-Si-Ta2O5(5 nm), Al-p-Si-Si3N4(1 or 2 nm)-Ta2O5 (5 nm), and Al-p-Si-SiO2(3.6 nm)-Ta2O5(5 nm) layer structures are characterized in buffer solution with different pH values by means of capacitance-voltage and constant capacitance method. The SiO2 and Si3N4 gate insulators are deposited by rapid thermal oxidation and rapid thermal nitridation, respectively, whereas the Ta2O5 film is prepared by atomic layer deposition. All EISCAP systems have a clear pH response, favoring the stacked gate insulators SiO2-Ta2O5 when considering the overall sensor characteristics, while the Si3N4(1 nm)-Ta2O5 stack delivers the largest accumulation capacitance (due to the lower equivalent oxide thickness) and a higher steepness in the slope of the capacitance-voltage curve among the studied stacked gate insulator systems.},
  language  = {en}
}
@article{MolinnusJanusFangetal.2022,
  author    = {Molinnus, Denise and Janus, Kevin Alexander and Fang, Anyelina C. and Drinic, Aleksander and Achtsnicht, Stefan and K{\"o}pf, Marius and Keusgen, Michael and Sch{\"o}ning, Michael Josef},
  title     = {Thick-film carbon electrode deposited onto a biodegradable fibroin substrate for biosensing applications},
  series = {Physica status solidi (a)},
  volume    = {219},
  journal   = {Physica status solidi (a)},
  number    = {23},
  publisher = {Wiley-VCH},
  address   = {Weinheim},
  issn      = {1862-6319},
  doi       = {10.1002/pssa.202200100},
  pages     = {1 -- 9},
  year      = {2022},
  abstract  = {This study addresses a proof-of-concept experiment with a biocompatible screen-printed carbon electrode deposited onto a biocompatible and biodegradable substrate, which is made of fibroin, a protein derived from silk of the Bombyx mori silkworm. To demonstrate the sensor performance, the carbon electrode is functionalized as a glucose biosensor with the enzyme glucose oxidase and encapsulated with a silicone rubber to ensure biocompatibility of the contact wires. The carbon electrode is fabricated by means of thick-film technology including a curing step to solidify the carbon paste. The influence of the curing temperature and curing time on the electrode morphology is analyzed via scanning electron microscopy. The electrochemical characterization of the glucose biosensor is performed by amperometric/voltammetric measurements of different glucose concentrations in phosphate buffer. Herein, systematic studies at applied potentials from 500 to 1200 mV to the carbon working electrode (vs the Ag/AgCl reference electrode) allow to determine the optimal working potential. Additionally, the influence of the curing parameters on the glucose sensitivity is examined over a time period of up to 361 days. The sensor shows a negligible cross-sensitivity toward ascorbic acid, noradrenaline, and adrenaline. The developed biocompatible biosensor is highly promising for future in vivo and epidermal applications.},
  language  = {en}
}
@article{MonakhovaDiehl2022,
  author    = {Monakhova, Yulia and Diehl, Bernd W.K.},
  title     = {Multinuclear NMR screening of pharmaceuticals using standardization by 2H integral of a deuterated solvent},
  series = {Journal of Pharmaceutical and Biomedical Analysis},
  volume    = {209},
  journal   = {Journal of Pharmaceutical and Biomedical Analysis},
  number    = {Article number: 114530},
  publisher = {Elsevier},
  isbn      = {0731-7085},
  doi       = {10.1016/j.jpba.2021.114530},
  year      = {2022},
  abstract  = {NMR standardization approach that uses the 2H integral of deuterated solvent for quantitative multinuclear analysis of pharmaceuticals is described. As a proof of principle, the existing NMR procedure for the analysis of heparin products according to US Pharmacopeia monograph is extended to the determination of Na+ and Cl- content in this matrix. Quantification is performed based on the ratio of a 23Na (35Cl) NMR integral and 2H NMR signal of deuterated solvent, D2O, acquired using the specific spectrometer hardware. As an alternative, the possibility of 133Cs standardization using the addition of Cs2CO3 stock solution is shown. Validation characteristics (linearity, repeatability, sensitivity) are evaluated. A holistic NMR profiling of heparin products can now also be used for the quantitative determination of inorganic compounds in a single analytical run using a single sample. In general, the new standardization methodology provides an appealing alternative for the NMR screening of inorganic and organic components in pharmaceutical products.},
  language  = {en}
}
@article{MonakhovaDiehl2022,
  author    = {Monakhova, Yulia and Diehl, Bernd W.K.},
  title     = {Nuclear magnetic resonance spectroscopy as an elegant tool for a complete quality control of crude heparin material},
  series = {Journal of Pharmaceutical and Biomedical Analysis},
  volume    = {219},
  journal   = {Journal of Pharmaceutical and Biomedical Analysis},
  number    = {Article number: 114915},
  publisher = {Elsevier},
  address   = {New York, NY},
  issn      = {0731-7085},
  doi       = {10.1016/j.jpba.2022.114915},
  year      = {2022},
  abstract  = {Nuclear magnetic resonance (NMR) spectrometric methods for the quantitative analysis of pure heparin in crude heparin is proposed. For quantification, a two-step routine was developed using a USP heparin reference sample for calibration and benzoic acid as an internal standard. The method was successfully validated for its accuracy, reproducibility, and precision. The methodology was used to analyze 20 authentic porcine heparinoid samples having heparin content between 4.25 w/w \% and 64.4 w/w \%. The characterization of crude heparin products was further extended to a simultaneous analysis of these common ions: sodium, calcium, acetate and chloride. A significant, linear dependence was found between anticoagulant activity and assayed heparin content for thirteen heparinoids samples, for which reference data were available. A Diffused-ordered NMR experiment (DOSY) can be used for qualitative analysis of specific glycosaminoglycans (GAGs) in heparinoid matrices and, potentially, for quantitative prediction of molecular weight of GAGs. NMR spectrometry therefore represents a unique analytical method suitable for the simultaneous quantitative control of organic and inorganic composition of crude heparin samples (especially heparin content) as well as an estimation of other physical and quality parameters (molecular weight, animal origin and activity).},
  language  = {en}
}
@article{MonakhovaSobolevaFedotovaetal.2022,
  author    = {Monakhova, Yulia and Soboleva, Polina M. and Fedotova, Elena S. and Musina, Kristina T. and Burmistrova, Natalia A.},
  title     = {Quantum chemical calculations of IR spectra of heparin disaccharide subunits},
  series = {Computational and Theoretical Chemistry},
  volume    = {1217},
  journal   = {Computational and Theoretical Chemistry},
  number    = {Article number: 113891},
  publisher = {Elsevier},
  address   = {New York, NY},
  isbn      = {2210-271X},
  doi       = {10.1016/j.comptc.2022.113891},
  year      = {2022},
  abstract  = {Heparin is a natural polysaccharide, which plays essential role in many biological processes. Alterations in building blocks can modify biological roles of commercial heparin products, due to significant changes in the conformation of the polymer chain. The variability structure of heparin leads to difficulty in quality control using different analytical methods, including infrared (IR) spectroscopy. In this paper molecular modelling of heparin disaccharide subunits was performed using quantum chemistry. The structural and spectral parameters of these disaccharides have been calculated using RHF/6-311G. In addition, over-sulphated chondroitin sulphate disaccharide was studied as one of the most widespread contaminants of heparin. Calculated IR spectra were analyzed with respect to specific structure parameters. IR spectroscopic fingerprint was found to be sensitive to substitution pattern of disaccharide subunits. Vibrational assignments of calculated spectra were correlated with experimental IR spectral bands of native heparin. Chemometrics was used to perform multivariate analysis of simulated spectral data.},
  language  = {en}
}
@article{MorandiButenwegBreisetal.2022,
  author    = {Morandi, Paolo and Butenweg, Christoph and Breis, Khaled and Beyer, Katrin and Magenes, Guido},
  title     = {Latest findings on the behaviour factor q for the seismic design of URM buildings},
  series = {Bulletin of Earthquake Engineering},
  volume    = {20},
  journal   = {Bulletin of Earthquake Engineering},
  number    = {11},
  editor    = {Ansal, Atilla},
  publisher = {Springer Nature},
  address   = {Cham},
  issn      = {1573-1456},
  doi       = {10.1007/s10518-022-01419-7},
  pages     = {5797 -- 5848},
  year      = {2022},
  abstract  = {Recent earthquakes as the 2012 Emilia earthquake sequence showed that recently built unreinforced masonry (URM) buildings behaved much better than expected and sustained, despite the maximum PGA values ranged between 0.20-0.30 g, either minor damage or structural damage that is deemed repairable. Especially low-rise residential and commercial masonry buildings with a code-conforming seismic design and detailing behaved in general very well without substantial damages. The low damage grades of modern masonry buildings that was observed during this earthquake series highlighted again that codified design procedures based on linear analysis can be rather conservative. Although advances in simulation tools make nonlinear calculation methods more readily accessible to designers, linear analyses will still be the standard design method for years to come. The present paper aims to improve the linear seismic design method by providing a proper definition of the q-factor of URM buildings. These q-factors are derived for low-rise URM buildings with rigid diaphragms which represent recent construction practise in low to moderate seismic areas of Italy and Germany. The behaviour factor components for deformation and energy dissipation capacity and for overstrength due to the redistribution of forces are derived by means of pushover analyses. Furthermore, considerations on the behaviour factor component due to other sources of overstrength in masonry buildings are presented. As a result of the investigations, rationally based values of the behaviour factor q to be used in linear analyses in the range of 2.0-3.0 are proposed.},
  language  = {en}
}
@inproceedings{MorandiButenwegBreisetal.2022,
  author    = {Morandi, Paolo and Butenweg, Christoph and Breis, Khaled and Beyer, Katrin and Magenes, Guido},
  title     = {Behaviour factor q for the seismic design of URM buildings},
  series = {The Third European Conference on Earthquake Engineering and Seismology},
  booktitle = {The Third European Conference on Earthquake Engineering and Seismology},
  editor    = {Arion, Cristian and Scupin, Alexandra and Ţigănescu, Alexandru},
  isbn      = {978-973-100-533-1},
  pages     = {1184 -- 1194},
  year      = {2022},
  abstract  = {Recent earthquakes showed that low-rise URM buildings following codecompliant seismic design and details behaved in general very well without substantial damages. Although advances in simulation tools make nonlinear calculation methods more readily accessible to designers, linear analyses will still be the standard design method for years to come. The present paper aims to improve the linear seismic design method by providing a proper definition of the q-factor of URM buildings. Values of q-factors are derived for low-rise URM buildings with rigid diaphragms, with reference to modern structural configurations realized in low to moderate seismic areas of Italy and Germany. The behaviour factor components for deformation and energy dissipation capacity and for overstrength due to the redistribution of forces are derived by means of pushover analyses. As a result of the investigations, rationally based values of the behaviour factor q to be used in linear analyses in the range of 2.0 to 3.0 are proposed.},
  language  = {en}
}
@article{MuellerSeginWeigandetal.2022,
  author    = {Mueller, Tobias and Segin, Alexander and Weigand, Christoph and Schmitt, Robert H.},
  title     = {Feature selection for measurement models},
  series = {International journal of quality \& reliability management},
  journal   = {International journal of quality \& reliability management},
  number    = {Vol. ahead-of-print, No. ahead-of-print.},
  publisher = {Emerald Group Publishing Limited},
  address   = {Bingley},
  issn      = {0265-671X},
  doi       = {10.1108/IJQRM-07-2021-0245},
  year      = {2022},
  abstract  = {Purpose In the determination of the measurement uncertainty, the GUM procedure requires the building of a measurement model that establishes a functional relationship between the measurand and all influencing quantities. Since the effort of modelling as well as quantifying the measurement uncertainties depend on the number of influencing quantities considered, the aim of this study is to determine relevant influencing quantities and to remove irrelevant ones from the dataset. Design/methodology/approach In this work, it was investigated whether the effort of modelling for the determination of measurement uncertainty can be reduced by the use of feature selection (FS) methods. For this purpose, 9 different FS methods were tested on 16 artificial test datasets, whose properties (number of data points, number of features, complexity, features with low influence and redundant features) were varied via a design of experiments. Findings Based on a success metric, the stability, universality and complexity of the method, two FS methods could be identified that reliably identify relevant and irrelevant influencing quantities for a measurement model. Originality/value For the first time, FS methods were applied to datasets with properties of classical measurement processes. The simulation-based results serve as a basis for further research in the field of FS for measurement models. The identified algorithms will be applied to real measurement processes in the future.},
  language  = {en}
}
@inproceedings{NiederwestbergSchneiderTeixeiraBouraetal.2022,
  author    = {Niederwestberg, Stefan and Schneider, Falko and Teixeira Boura, Cristiano Jos{\´e} and Herrmann, Ulf},
  title     = {Introduction to a direct irradiated transparent tube particle receiver},
  series = {SOLARPACES 2020},
  booktitle = {SOLARPACES 2020},
  number    = {2445 / 1},
  publisher = {AIP conference proceedings / American Institute of Physics},
  address   = {Melville, NY},
  isbn      = {978-0-7354-4195-8},
  issn      = {1551-7616 (online)},
  doi       = {10.1063/5.0086735},
  pages     = {9 Seiten},
  year      = {2022},
  abstract  = {New materials often lead to innovations and advantages in technical applications. This also applies to the particle receiver proposed in this work that deploys high-temperature and scratch resistant transparent ceramics. With this receiver design, particles are heated through direct-contact concentrated solar irradiance while flowing downwards through tubular transparent ceramics from top to bottom. In this paper, the developed particle receiver as well as advantages and disadvantages are described. Investigations on the particle heat-up characteristics from solar irradiance were carried out with DEM simulations which indicate that particle temperatures can reach up to 1200 K. Additionally, a simulation model was set up for investigating the dynamic behavior. A test receiver at laboratory scale has been designed and is currently being built. In upcoming tests, the receiver test rig will be used to validate the simulation results. The design and the measurement equipment is described in this work.},
  language  = {en}
}
@article{OjovanSteinmetz2022,
  author    = {Ojovan, Michael I. and Steinmetz, Hans-J{\"u}rgen},
  title     = {Approaches to Disposal of Nuclear Waste},
  series = {Energies},
  volume    = {15},
  journal   = {Energies},
  number    = {20},
  publisher = {MDPI},
  address   = {Basel},
  issn      = {1996-1073},
  doi       = {10.3390/en15207804},
  pages     = {Artikel 7804},
  year      = {2022},
  abstract  = {We present a concise mini overview on the approaches to the disposal of nuclear waste currently used or deployed. The disposal of nuclear waste is the end point of nuclear waste management (NWM) activities and is the emplacement of waste in an appropriate facility without the intention to retrieve it. The IAEA has developed an internationally accepted classification scheme based on the end points of NWM, which is used as guidance. Retention times needed for safe isolation of waste radionuclides are estimated based on the radiotoxicity of nuclear waste. Disposal facilities usually rely on a multi-barrier defence system to isolate the waste from the biosphere, which comprises the natural geological barrier and the engineered barrier system. Disposal facilities could be of a trench type, vaults, tunnels, shafts, boreholes, or mined repositories. A graded approach relates the depth of the disposal facilities' location with the level of hazard. Disposal practices demonstrate the reliability of nuclear waste disposal with minimal expected impacts on the environment and humans.},
  language  = {en}
}
@inproceedings{OstkottePetersHueningetal.2022,
  author    = {Ostkotte, Sebastian and Peters, Constantin and H{\"u}ning, Felix and Bragard, Michael},
  title     = {Design, implementation and verification of an rotational incremental position encoder based on the magnetic Wiegand effect},
  series = {2022 ELEKTRO (ELEKTRO)},
  booktitle = {2022 ELEKTRO (ELEKTRO)},
  publisher = {IEEE},
  isbn      = {978-1-6654-6726-1},
  issn      = {2691-0616},
  doi       = {10.1109/ELEKTRO53996.2022.9803477},
  pages     = {6 Seiten},
  year      = {2022},
  abstract  = {This paper covers the use of the magnetic Wiegand effect to design an innovative incremental encoder. First, a theoretical design is given, followed by an estimation of the achievable accuracy and an optimization in open-loop operation. Finally, a successful experimental verification is presented. For this purpose, a permanent magnet synchronous machine is controlled in a field-oriented manner, using the angle information of the prototype.},
  language  = {en}
}