@article{HafidiElHatkaSchmitzetal.2024,
  author    = {Hafidi, Youssef and El Hatka, Hicham and Schmitz, Dominik and Krauss, Manuel and Pettrak, J{\"u}rgen and Biel, Markus and Ittobane, Najim},
  title     = {Sustainable soil additives for water and micronutrient supply: swelling and chelating properties of polyaspartic acid hydrogels utilizing newly developed crosslinkers},
  series = {Gels},
  volume    = {10},
  journal   = {Gels},
  number    = {3},
  publisher = {MDPI},
  address   = {Basel},
  issn      = {2310-2861},
  doi       = {10.3390/gels10030170},
  pages     = {Artikel 170},
  year      = {2024},
  abstract  = {Drought and water shortage are serious problems in many arid and semi-arid regions. This problem is getting worse and even continues in temperate climatic regions due to climate change. To address this problem, the use of biodegradable hydrogels is increasingly important for the application as water-retaining additives in soil. Furthermore, efficient (micro-)nutrient supply can be provided by the use of tailored hydrogels. Biodegradable polyaspartic acid (PASP) hydrogels with different available (1,6-hexamethylene diamine (HMD) and L-lysine (LYS)) and newly developed crosslinkers based on diesters of glycine (GLY) and (di-)ethylene glycol (DEG and EG, respectively) were synthesized and characterized using Fourier transform infrared (FTIR) spectroscopy and scanning electron microscopy (SEM) and regarding their swelling properties (kinetic, absorbency under load (AUL)) as well as biodegradability of PASP hydrogel. Copper (II) and zinc (II), respectively, were loaded as micronutrients in two different approaches: in situ with crosslinking and subsequent loading of prepared hydrogels. The results showed successful syntheses of di-glycine-ester-based crosslinkers. Hydrogels with good water-absorbing properties were formed. Moreover, the developed crosslinking agents in combination with the specific reaction conditions resulted in higher water absorbency with increased crosslinker content used in synthesis (10\% vs. 20\%). The prepared hydrogels are candidates for water-storing soil additives due to the biodegradability of PASP, which is shown in an exemple. The incorporation of Cu(II) and Zn(II) ions can provide these micronutrients for plant growth.},
  language  = {en}
}
@article{ElBerguiAbouabdillahBouriougetal.2023,
  author    = {El Bergui, Omnia and Abouabdillah, Aziz and Bourioug, Mohamed and Schmitz, Dominik and Biel, Markus and Aboudrare, Abdellah and Krauss, Manuel and Jomaa, Ahlem and Romuli, Sebastian and M{\"u}ller, Joachim and Fagroud, Mustapha and Bouabid, Rachid},
  title     = {Innovative solutions for drought: Evaluating hydrogel application on onion cultivation (Allium cepa) in Morocco},
  series = {Water},
  volume    = {15},
  journal   = {Water},
  number    = {11},
  publisher = {MDPI},
  address   = {Basel},
  doi       = {10.3390/w15111972},
  pages     = {Artikel 1972},
  year      = {2023},
  abstract  = {Throughout the last decade, and particularly in 2022, water scarcity has become a critical concern in Morocco and other Mediterranean countries. The lack of rainfall during spring was worsened by a succession of heat waves during the summer. To address this drought, innovative solutions, including the use of new technologies such as hydrogels, will be essential to transform agriculture. This paper presents the findings of a study that evaluated the impact of hydrogel application on onion (Allium cepa) cultivation in Meknes, Morocco. The treatments investigated in this study comprised two different types of hydrogel-based soil additives (Arbovit® polyacrylate and Huminsorb® polyacrylate), applied at two rates (30 and 20 kg/ha), and irrigated at two levels of water supply (100\% and 50\% of daily crop evapotranspiration; ETc). Two control treatments were included, without hydrogel application and with both water amounts. The experiment was conducted in an open field using a completely randomized design. The results indicated a significant impact of both hydrogel-type dose and water dose on onion plant growth, as evidenced by various vegetation parameters. Among the hydrogels tested, Huminsorb® Polyacrylate produced the most favorable outcomes, with treatment T9 (100\%, HP, 30 kg/ha) yielding 70.55 t/ha; this represented an increase of 11 t/ha as compared to the 100\% ETc treatment without hydrogel application. Moreover, the combination of hydrogel application with 50\% ETc water stress showed promising results, with treatment T4 (HP, 30 kg, 50\%) producing almost the same yield as the 100\% ETc treatment without hydrogel while saving 208 mm of water.},
  language  = {en}
}
@book{Lauth2023,
  author    = {Lauth, Jakob},
  title     = {Physical chemistry in a nutshell: Basics for engineers and scientists},
  publisher = {Springer},
  address   = {Berlin},
  isbn      = {978-3-662-67636-3 (Softcover)},
  doi       = {10.1007/978-3-662-67637-0},
  pages     = {XIII, 248 Seiten},
  year      = {2023},
  abstract  = {This book is based on a multimedia course for biological and chemical engineers, which is designed to trigger students' curiosity and initiative. A solid basic knowledge of thermodynamics and kinetics is necessary for understanding many technical, chemical, and biological processes. The one-semester basic lecture course was divided into 12 workshops (chapters). Each chapter covers a practically relevant area of physical chemistry and contains the following didactic elements that make this book particularly exciting and understandable: - Links to Videos at the start of each chapter as preparation for the workshop - Key terms (in bold) for further research of your own - Comprehension questions and calculation exercises with solutions as learning checks - Key illustrations as simple, easy-to-replicate blackboard pictures Humorous cartoons for each workshop (by Faelis) additionally lighten up the text and facilitate the learning process as a mnemonic. To round out the book, the appendix includes a summary of the most popular experiments in basic physical chemistry courses, as well as suggestions for designing workshops with exhibits, experiments, and "questions of the day." Suitable for students minoring in chemistry; chemistry majors are sure to find this slimmed-down, didactically valuable book helpful as well. The book is excellent for self-study.},
  language  = {en}
}
@article{EckertAbbasiMangetal.2020,
  author    = {Eckert, Alexander and Abbasi, Mozhdeh and Mang, Thomas and Saalw{\"a}chter, Kay and Walther, Andreas},
  title     = {Structure, Mechanical Properties, and Dynamics of Polyethylenoxide/Nanoclay Nacre-Mimetic Nanocomposites},
  series = {Macromolecules},
  volume    = {53},
  journal   = {Macromolecules},
  number    = {5},
  publisher = {ACS Publications},
  address   = {Washington, DC},
  issn      = {1520-5835},
  doi       = {10.1021/acs.macromol.9b01931},
  pages     = {1716 -- 1725},
  year      = {2020},
  abstract  = {Nacre-mimetic nanocomposites based on high fractions of synthetic high-aspect-ratio nanoclays in combination with polymers are continuously pushing boundaries for advanced material properties, such as high barrier against oxygen, extraordinary mechanical behavior, fire shielding, and glass-like transparency. Additionally, they provide interesting model systems to study polymers under nanoconfinement due to the well-defined layered nanocomposite arrangement. Although the general behavior in terms of forming such layered nanocomposite materials using evaporative self-assembly and controlling the nanoclay gallery spacing by the nanoclay/polymer ratio is understood, some combinations of polymer matrices and nanoclay reinforcement do not comply with the established models. Here, we demonstrate a thorough characterization and analysis of such an unusual polymer/nanoclay pair that falls outside of the general behavior. Poly(ethylene oxide) (PEO) and sodium fluorohectorite form nacre-mimetic, lamellar nanocomposites that are completely transparent and show high mechanical stiffness and high gas barrier, but there is only limited expansion of the nanoclay gallery spacing when adding increasing amounts of polymer. This behavior is maintained for molecular weights of PEO varied over four orders of magnitude and can be traced back to depletion forces. By careful investigation via X-ray diffraction and proton low-resolution solid-state NMR, we are able to quantify the amount of mobile and immobilized polymer species in between the nanoclay galleries and around proposed tactoid stacks embedded in a PEO matrix. We further elucidate the unusual confined polymer dynamics, indicating a relevant role of specific surface interactions.},
  language  = {en}
}
@article{ElMoussaouiTalbiAtmaneetal.2020,
  author    = {El Moussaoui, Noureddine and Talbi, Sofian and Atmane, Ilyas and Kassmi, Khalil and Schwarzer, Klemens and Chayeb, Hamid and Bachiri, Najib},
  title     = {Feasibility of a new design of a Parabolic Trough Solar Thermal Cooker (PSTC)},
  series = {Solar Energy},
  volume    = {201},
  journal   = {Solar Energy},
  number    = {Vol. 201 (May 2020)},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0038-092X},
  doi       = {10.1016/j.solener.2020.03.079},
  pages     = {866 -- 871},
  year      = {2020},
  abstract  = {In this article, we describe the structure, the functioning, and the tests of parabolic trough solar thermal cooker (PSTC). This oven is designed to meet the needs of rural residents, including Urban, which requires stable cooking temperatures above 200 °C. The cooking by this cooker is based on the concentration of the sun's rays on a glass vacuum tube and heating of the oil circulate in a big tube, located inside the glass tube. Through two small tubes, associated with large tube, the heated oil, rise and heats the pot of cooking pot containing the food to be cooked (capacity of 5 kg). This cooker is designed in Germany and extensively tested in Morocco for use by the inhabitants who use wood from forests. During a sunny day, having a maximum solar radiation around 720 W/m2 and temperature ambient around 26 °C, maximum temperatures recorded of the small tube, the large tube and the center of the pot are respectively: 370 °C, 270 °C and 260 °C. The cooking process with food at high (fries, ..), we show that the cooking oil temperature rises to 200 °C, after 1 h of heating, the cooking is done at a temperature of 120 °C for 20 min. These temperatures are practically stable following variations and decreases in the intensity of irradiance during the day. The comparison of these results with those of the literature shows an improvement of 30-50 \% on the maximum value of the temperature with a heat storage that could reach 60 min of autonomy. All the results obtained show the good functioning of the PSTC and the feasibility of cooking food at high temperature (>200 °C).},
  language  = {en}
}
@misc{DauerHojdisMuelleretal.2019,
  author    = {Dauer, David-Raphael and Hojdis, Nils and M{\"u}ller, Norbert and Recker, Carla and Schax, Fabian and Sch{\"o}ffel, Julia and Tarantola, Gesa and Weber, Christine},
  title     = {Schwefelvernetzbare Kautschukmischung, Vulkanisat der Kautschukmischung und Fahrzeugreifen},
  year      = {2019},
  abstract  = {Die Erfindung betrifft eine schwefelvernetzbare Kautschukmischung, deren Vulkanisat und einen Fahrzeugreifen. Die schwefelvernetzbare Kautschukmischung enth{\"a}lt wenigstens die folgenden Bestandteile: - wenigstens einen Dienkautschuk; und - 10 bis 300 phr wenigstens einer Kiesels{\"a}ure; und - 1 bis 30 phf wenigstens eines Silans A mit der allgemeinen Summenformel A-I) A-I)(R1)oSi-R2-(S-R3)q-S-X; und - 0,5 bis 30 phf wenigstens eines Silans B mit der allgemeinen Summenformel B-I) B-I) (R1)oSi-R2-(S-R3)u-S-R2-Si(R1)o wobei q =1, 2 oder 3 ist; und u = 1, 2 oder 3 ist; und X ein Wasserstoffatom oder eine -C(=O)-R8 Gruppe ist wobei R8 ausgew{\"a}hlt ist aus Wasserstoff, C1-C20 Alkylgruppen, vorzugsweise C1-C17, C6-C20- Arylgruppen, vorzugsweise Phenyl, C2-C20-Alkenylgruppen und C7-C20-Aralkylgruppen.},
  language  = {de}
}
@misc{HojdisMulthauptReckeretal.2019,
  author    = {Hojdis, Nils and Multhaupt, Hendrik and Recker, Carla and Wark, Michael},
  title     = {Schwefelvernetzbare Kautschukmischung, Vulkanisat der Kautschukmischung und Fahrzeugreifen},
  year      = {2019},
  abstract  = {Die Erfindung betrifft eine schwefelvernetzbare Kautschukmischung, deren Vulkanisat und einen Fahrzeugreifen. Die erfindungsgem{\"a}ße Kautschukmischung enth{\"a}lt wenigstens folgende Bestandteile: - Wenigstens einen Dienkautschuk; - wenigstens eine Kohle (HTC-Kohle), die mittels hydrothermaler Karbonisierung von wenigstens einer Ausgangssubstanz hergestellt ist. Der erfindungsgem{\"a}ße Fahrzeugreifen weist in wenigstens einem Bauteil wenigstens ein erfindungsgem{\"a}ßes Vulkanisat der Kautschukmischung auf.},
  language  = {de}
}
@misc{FriedericiHojdis2018,
  author    = {Friederici, Nadja-Annette and Hojdis, Nils},
  title     = {Fahrzeugreifen},
  year      = {2018},
  abstract  = {Die Erfindung betrifft einen Fahrzeugreifen mit zumindest einem radial außen befindlichen Gummilaufstreifen, Wulstbereichen f{\"u}r den Anschluss an eine Felge und mit auf einer Gummimischung basierenden Seitenwandbereichen zwischen Gummilaufstreifen und den Wulstbereichen. Ferner betrifft die Erfindung Verfahren zur Herstellung solcher Fahrzeugreifen. Um den Anteil der umweltsch{\"a}dlichen Substanzen, insbesondere im Innenstadtbereich, zu reduzieren weisen die Seitenwandbereiche auf der {\"a}ußeren Oberfl{\"a}che eine f{\"u}r den oxidativen Abbau von Molek{\"u}len photokatalytisch aktive Substanz auf.},
  language  = {de}
}
@misc{DauerHojdisMuelleretal.2019,
  author    = {Dauer, David-Raphael and Hojdis, Nils and M{\"u}ller, Norbert and Recker, Carla and Schax, Fabian and Sch{\"o}ffel, Julia and Tarantola, Gesa and Weber, Christine},
  title     = {Schwefelvernetzbare Kautschukmischung, Vulkanisat der Kautschukmischung und Fahrzeugreifen},
  year      = {2019},
  abstract  = {Die Erfindung betrifft eine schwefelvernetzbare Kautschukmischung, deren Vulkanisat und einen Fahrzeugreifen.Die schwefelvernetzbare Kautschukmischung enth{\"a}lt wenigstens die folgenden Bestandteile:- wenigstens einen Dienkautschuk; und- 10 bis 300 phr wenigstens einer Kiesels{\"a}ure ; und- 1 bis 30 phf wenigstens eines Silans A mit der allgemeinen Summenformel A-I)und- 0,5 bis 30 phf wenigstens eines Silans B mit der allgemeinen Summenformel B-I)wobei u gleich 0, 1, 2 oder 3 und v gleich 0 oder 1 ist.},
  language  = {de}
}
@misc{Hojdis2019,
  author    = {Hojdis, Nils},
  title     = {Verfahren zum Bestimmen einer Sitzeinstellung eines Sitzes eines Kraftfahrzeugs, Computerprogrammprodukt, Servereinrichtung, Kommunikationsendger{\"a}t und Kraftfahrzeug},
  year      = {2019},
  abstract  = {Die Erfindung betrifft ein Verfahren zum Bestimmen einer Sitzeinstellung (23) eines Sitzes (3) eines Kraftfahrzeugs (1), bei welchem folgende Schritte durchgef{\"u}hrt werden:- Bereitstellen einer K{\"o}rperabmessung (12) eines Nutzers (6) des Kraftfahrzeugs (1);- Bereitstellen einer Sitzeigenschaft (13) des Sitzes (3) des Kraftfahrzeugs (1);- Bereitstellen eines mit zumindest einer Referenzsitzeigenschaft (20), zumindest einer Referenzk{\"o}rperabmessung (21) und zumindest einer Referenzsitzeinstellung (22) trainiertes k{\"u}nstliches neuronales Netz (14); und- Bestimmen der Sitzeinstellung (23) durch Eingabe der K{\"o}rperabmessung (12) und der Sitzeigenschaft (13) in das k{\"u}nstliche neuronale Netz (14).},
  language  = {de}
}