@article{YazdanbakhshSolbachBitz2012,
  author    = {Yazdanbakhsh, Pedram and Solbach, Klaus and Bitz, Andreas},
  title     = {Variable power combiner for RF mode shimming in 7-T MR imaging},
  series = {IEEE Transaction on Biomedical Engineering},
  volume    = {59},
  journal   = {IEEE Transaction on Biomedical Engineering},
  number    = {9},
  publisher = {IEEE},
  address   = {New York},
  issn      = {1558-2531},
  doi       = {10.1109/TBME.2012.2205926},
  pages     = {2549 -- 2557},
  year      = {2012},
  abstract  = {This contribution discusses the utilization of RF power in an MRI system with RF mode shimming which enables the superposition of circularly polarized modes of a transmit RF coil array driven by a Butler matrix. Since the required power for the individual modes can vary widely, mode-shimming can result in a significant underutilization of the total available RF power. A variable power combiner (VPC) is proposed to improve the power utilization: it can be realized as a reconfiguration of the MRI transmit system by the inclusion of one additional matrix network which receives the power from all transmit amplifiers at its input ports and provides any desired (combined) power distribution at its output ports by controlling the phase and amplitude of the amplifiers' input signals. The power distribution at the output ports of the VPC is then fed into the "mode" ports of the coil array Butler matrix in order to superimpose the spatial modes at the highest achievable power utilization. The VPC configuration is compared to the standard configuration of the transmit chain of our MRI system with 8 transmit channels and 16 coils. In realistic scenarios, improved power utilization was achieved from 17\% to 60\% and from 14\% to 55\% for an elliptical phantom and a region of interest in the abdomen, respectively, and an increase of the power utilization of 1 dB for a region of interest in the upper leg. In general, it is found that the VPC allows significant improvement in power utilization when the shimming solution demands only a few modes to be energized, while the technique can yield loss in power utilization in cases with many modes required at high power level.},
  language  = {en}
}
@article{Wolf2012,
  author    = {Wolf, Martin},
  title     = {Von Security Awareness zum Secure Behaviour},
  series = {Hakin9 Extra - IT-Forensik},
  volume    = {2012},
  journal   = {Hakin9 Extra - IT-Forensik},
  number    = {5},
  publisher = {Software Wydawnictwo},
  address   = {Warszawa},
  issn      = {1733-7186},
  pages     = {18 -- 19},
  year      = {2012},
  abstract  = {Security Awareness ist derzeit ein viel diskutiertes Thema. Es reicht nicht, einfach nur ein paar technische Systeme (z.B. Firewalls) zu installieren, um ein angemessenes Schutzniveau zu erzielen. Neben einer guten Organisation von IT Security ist es auch notwendig, den Mitarbeiter einzubinden. Der vielzitierte "Faktor Mensch" ist derjenige, der die Technik korrekt anwenden muss und der durch falsches Verhalten technische und organisatorische Schutzmaßnahmen aushebeln kann. Deshalb reicht es nicht aus, wenn sich der Mitarbeiter der Gefahren bewusst ("aware") ist, er muss auch dementsprechend "sicher" handeln.},
  language  = {de}
}
@article{Wilke2012,
  author    = {Wilke, Thomas},
  title     = {Architekturzeichnung als Instrument der Theoriebildung. Lineamenta vs. Portraicture - Architekturdarstellung zwischen Wissenschaft und {\"O}ffentlichkeit. Tagung des DFG-Netzwerks-Schnittstelle Bild in Zusammenarbeit mit dem Lehrstuhl f{\"u}r Kunstgeschichte der Universit{\"a}t Regensburg, 28.4.2012.},
  series = {Kunstchronik},
  volume    = {65},
  journal   = {Kunstchronik},
  number    = {9/10},
  publisher = {Fachverlag Hans Carl},
  address   = {N{\"u}rnberg},
  issn      = {0023-5474},
  pages     = {494 -- 499},
  year      = {2012},
  language  = {de}
}
@article{WernerWagnerMiyamotoetal.2012,
  author    = {Werner, Frederik and Wagner, Torsten and Miyamoto, Ko-ichiro and Yoshinobu, Tatsuo and Sch{\"o}ning, Michael Josef},
  title     = {High speed and high resolution chemical imaging based on a new type of OLED-LAPS set-up},
  series = {Sensors and Actuators B: Chemical},
  volume    = {175},
  journal   = {Sensors and Actuators B: Chemical},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0925-4005},
  doi       = {10.1016/j.snb.2011.12.102},
  pages     = {118 -- 122},
  year      = {2012},
  abstract  = {Light-addressable potentiometric sensors (LAPS) are field-effect-based sensors. A modulated light source is used to define the particular measurement spot to perform spatially resolved measurements of chemical species and to generate chemical images. In this work, an organic-LED (OLED) display has been chosen as a light source. This allows high measurement resolution and miniaturisation of the system. A new developed driving method for the OLED display optimised for LAPS-based measurements is demonstrated. The new method enables to define modulation frequencies between 1 kHz and 16 kHz and hence, reduces the measurement time of a chemical image by a factor of 40 compared to the traditional addressing of an OLED display.},
  language  = {en}
}
@article{WernerGroebelKrumbeetal.2012,
  author    = {Werner, Frederik and Groebel, Simone and Krumbe, Christoph and Wagner, Torsten and Selmer, Thorsten and Yoshinobu, Tatsuo and Baumann, Marcus and Sch{\"o}ning, Michael Josef},
  title     = {Nutrient concentration-sensitive microorganism-based biosensor},
  series = {Physica Status Solidi (a)},
  volume    = {209},
  journal   = {Physica Status Solidi (a)},
  number    = {5},
  publisher = {Wiley-VCH},
  address   = {Weinheim},
  issn      = {1862-6319},
  doi       = {10.1002/pssa.201100801},
  pages     = {900 -- 904},
  year      = {2012},
  language  = {en}
}
@article{Weigand2012,
  author    = {Weigand, Christoph},
  title     = {Statistical Tests Based on Reliability and Precision},
  series = {Economic Quality Control : EQC ; international journal for quality and reliability},
  volume    = {27},
  journal   = {Economic Quality Control : EQC ; international journal for quality and reliability},
  number    = {1},
  publisher = {De Gruyter},
  address   = {Berlin},
  issn      = {1869-6147},
  doi       = {10.1515/eqc-2012-0002},
  pages     = {43 -- 64},
  year      = {2012},
  abstract  = {The construction of a statistical test is investigated which is based only on "reliability" and "precision" as quality criteria. The reliability of a statistical test is quantifiedin a straightforward way by the probability that the decision of the test is correct. However, the quantification of the precision of a statistical test is not at all evident. Thereforethe paper presents and discusses several approaches. Moreover the distinction of "nullhypothesis" and "alternative hypothesis" is not necessary any longer.},
  language  = {en}
}
@article{WagnerWernerMiyamotoetal.2012,
  author    = {Wagner, Torsten and Werner, Frederik and Miyamoto, Ko-Ichiro and Sch{\"o}ning, Michael Josef and Yoshinobu, Tatsuo},
  title     = {Development and characterisation of a compact light-addressable potentiometric sensor (LAPS) based on the digital light processing (DLP) technology for flexible chemical imaging},
  series = {Sensors and Actuators B: Chemical},
  volume    = {170},
  journal   = {Sensors and Actuators B: Chemical},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0925-4005},
  doi       = {10.1016/j.snb.2010.12.003},
  pages     = {34 -- 39},
  year      = {2012},
  abstract  = {Chemical imaging systems allow the visualisation of the distribution of chemical species on the sensor surface. This work represents a new flexible approach to read out light-addressable potentiometric sensors (LAPS) with the help of a digital light processing (DLP) set-up. The DLP, known well for video projectors, consists of a mirror-array MEMS device, which allows fast and flexible generation of light patterns. With the help of these light patterns, the sensor surface of the LAPS device can be addressed. The DLP approach has several advantages compared to conventional LAPS set-ups, e.g., the spot size and the shape of the light pointer can be changed easily and no mechanical movement is necessary, which reduces the size of the set-up and increases the stability and speed of the measurement. In addition, the modulation frequency and intensity of the light beam are important parameters of the LAPS set-up. Within this work, the authors will discuss two different ways of light modulation by the DLP set-up, investigate the influence of different modulation frequencies and different light intensities as well as demonstrate the scanning capabilities of the new set-up by pH mapping on the sensor surface.},
  language  = {en}
}
@article{WagnerShigiaharaMiyamotoetal.2012,
  author    = {Wagner, Torsten and Shigiahara, N. and Miyamoto, K. and Suzurikawa, J. and Finger, F. and Sch{\"o}ning, Michael Josef and Yoshinobu, T.},
  title     = {Light-addressable Potentiometric Sensors and Light-addressable Electrodes as a Combined Sensor-and-manipulator Microsystem with High Flexibility},
  series = {Procedia Engineering},
  journal   = {Procedia Engineering},
  number    = {47},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1877-7058},
  doi       = {10.1016/j.proeng.2012.09.290},
  pages     = {890 -- 893},
  year      = {2012},
  abstract  = {This work describes the novel combination of the light-addressable electrode (LAE) and the light-addressable potentiometric sensor (LAPS) into a microsystem set-up. Both the LAE as well as the LAPS shares the principle of addressing the active spot by means of a light beam. This enables both systems to manipulate resp. to detect an analyte with a high spatial resolution. Hence, combining both principles into a single set-up enables the active stimulation e.g., by means of electrolysis and a simultaneous observation e.g., the response of an entrapped biological cell by detection of extracellular pH changes. The work will describe the principles of both technologies and the necessary steps to integrate them into a single set-up. Furthermore, examples of application and operation of such systems will be presented.},
  language  = {en}
}
@article{VerbanellaFabo2012,
  author    = {Verbanella, Stresa and Fabo, Sabine},
  title     = {Mit Pinsel und Farbe hacken : Interview mit Sabine Fabo},
  series = {Remotewords.net},
  journal   = {Remotewords.net},
  year      = {2012},
  abstract  = {Remotewords makes its mark on the picturesque "Bar Verbanella", located in Stresa near Isola Bella on Lago Maggiore. The words CUM GRANO SALIS (with a grain of salt) by Sabine Fabo, art theorist on media contexts, were applied to its roof in collaboration with the German-Italian art organization "Lo spirito del Lago".},
  language  = {de}
}
@article{TimmeGuennewig2012,
  author    = {Timme, Michael and G{\"u}nnewig, Sebastian},
  title     = {Betriebskostenabrechnung - Die Pflicht des Vermieters zur Beachtung des Wirtschaftlichkeitsgebots},
  series = {Der Miet-Rechts-Berater : MietRB ; Miete, Immobilien, Wohnungseigentum},
  journal   = {Der Miet-Rechts-Berater : MietRB ; Miete, Immobilien, Wohnungseigentum},
  number    = {3},
  publisher = {Verlag Dr. Otto Schmidt},
  address   = {K{\"o}ln},
  issn      = {1612-040X},
  pages     = {83 -- 88},
  year      = {2012},
  abstract  = {Mit seiner aktuellen Entscheidung (BGH v. 6.11.2011 - VIII ZR 340/10, MDR 2011, 1095 = MietRB MDR 2011, 337) hat der BGH die Darlegungs- und Beweislast f{\"u}r einen Verstoß gegen das Gebot der Wirtschaftlichkeit bei der Abrechnung von Betriebskosten konkretisiert. Der Beitrag erl{\"a}utert anhand der Hintergr{\"u}nde des Gebotes der Wirtschaftlichkeit die Konsequenzen f{\"u}r die Praxis.},
  language  = {de}
}
@article{Timme2012,
  author    = {Timme, Michael},
  title     = {Die Reichweite der "werdenden" Wohnungseigent{\"u}mergemeinschaft gegen{\"u}ber dem Zweiterwerb},
  series = {Monatsschrift f{\"u}r Deutsches Recht : MdR},
  volume    = {2012},
  journal   = {Monatsschrift f{\"u}r Deutsches Recht : MdR},
  number    = {18},
  publisher = {Verlag Dr. Otto Schmidt},
  address   = {K{\"o}ln},
  issn      = {0340-1812},
  doi       = {10.9785/ovs-mdtr-2012-1069},
  pages     = {1068 -- 1071},
  year      = {2012},
  abstract  = {Mit einer aktuellen Entscheidung hat der BGH, Urt. v. 11.5.2012 - V ZR 196/11, MDR 2012, 958 seine Rechtsprechung v. 5.6.2008 - V ZB 85/07 zur Entstehungsphase einer Wohnungseigent{\"u}mergemeinschaft fortgef{\"u}hrt. In dieser Entscheidung sieht der BGH die Erwerber von Wohnungseigentum als Kostenschuldner gem. \S 16 Abs. 2 WEG an, obwohl diese noch nicht im Grundbuch eingetragen sind. Eine andere Rechtslage besteht beim sog. Zweiterwerb. Die Abgrenzung von Erstund Zweierwerb ist aufgrund der v{\"o}llig unterschiedlichen Rechtsfolgen f{\"u}r die Praxis von großer Bedeutung.},
  language  = {de}
}
@article{StadlerGarveyBocahutetal.2012,
  author    = {Stadler, Andreas M. and Garvey, G. J. and Bocahut, A. and Sacquin-Mora, S. and Digel, Ilya and Schneider, G. J. and Natali, F. and Artmann, Gerhard and Zaccai, G.},
  title     = {Thermal fluctuations of haemoglobin from different species : adaptation to temperature via conformational dynamics},
  series = {Journal of the Royal Society Interface},
  volume    = {9},
  journal   = {Journal of the Royal Society Interface},
  number    = {76},
  publisher = {The Royal Society},
  address   = {London},
  issn      = {1742-5689},
  doi       = {10.1098/rsif.2012.0364},
  pages     = {2845 -- 2855},
  year      = {2012},
  abstract  = {Thermodynamic stability, configurational motions and internal forces of haemoglobin (Hb) of three endotherms (platypus, Ornithorhynchus anatinus; domestic chicken, Gallus gallus domesticus and human, Homo sapiens) and an ectotherm (salt water crocodile, Crocodylus porosus) were investigated using circular dichroism, incoherent elastic neutron scattering and coarse-grained Brownian dynamics simulations. The experimental results from Hb solutions revealed a direct correlation between protein resilience, melting temperature and average body temperature of the different species on the 0.1 ns time scale. Molecular forces appeared to be adapted to permit conformational fluctuations with a root mean square displacement close to 1.2 {\AA} at the corresponding average body temperature of the endotherms. Strong forces within crocodile Hb maintain the amplitudes of motion within a narrow limit over the entire temperature range in which the animal lives. In fully hydrated powder samples of human and chicken, Hb mean square displacements and effective force constants on the 1 ns time scale showed no differences over the whole temperature range from 10 to 300 K, in contrast to the solution case. A complementary result of the study, therefore, is that one hydration layer is not sufficient to activate all conformational fluctuations of Hb in the pico- to nanosecond time scale which might be relevant for biological function. Coarse-grained Brownian dynamics simulations permitted to explore residue-specific effects. They indicated that temperature sensing of human and chicken Hb occurs mainly at residues lining internal cavities in the β-subunits.},
  language  = {en}
}
@article{StaatVu2012,
  author    = {Staat, Manfred and Vu, Duc Khoi},
  title     = {Limit analysis of flaws in pressurized pipes and cylindrical vessels Part II: Circumferential defects},
  series = {Engineering Fracture Mechanics ; 97(2013), H. 1},
  volume    = {97},
  journal   = {Engineering Fracture Mechanics ; 97(2013), H. 1},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0013-7944},
  doi       = {10.1016/j.engfracmech.2012.05.017},
  pages     = {314 -- 333},
  year      = {2012},
  abstract  = {Upper and lower bound theorems of limit analyses have been presented in part I of the paper. Part II starts with the finite element discretization of these theorems and demonstrates how both can be combined in a primal-dual optimization problem. This recently proposed numerical method is used to guide the development of a new class of closed-form limit loads for circumferential defects, which show that only large defects contribute to plastic collapse with a rapid loss of strength with increasing crack sizes. The formulae are compared with primal-dual FEM limit analyses and with burst tests. Even closer predictions are obtained with iterative limit load solutions for the von Mises yield function and for the Tresca yield function. Pressure loading of the faces of interior cracks in thick pipes reduces the collapse load of circumferential defects more than for axial flaws. Axial defects have been treated in part I of the paper.},
  language  = {en}
}
@article{StaatTrenzLohmannetal.2012,
  author    = {Staat, Manfred and Trenz, Eva and Lohmann, Philipp and Frotscher, Ralf and Klinge, Uwe and Tabaza, Ruth and Kirschner-Hermanns, Ruth},
  title     = {New measurements to compare soft tissue anchoring systems in pelvic floor surgery},
  series = {Journal of Biomedical Materials Research Part B: Applied Biomaterials},
  volume    = {100B},
  journal   = {Journal of Biomedical Materials Research Part B: Applied Biomaterials},
  number    = {4},
  publisher = {Wiley},
  address   = {Hoboken, NJ},
  issn      = {1552-4981},
  doi       = {10.1002/jbm.b.32654},
  pages     = {924 -- 933},
  year      = {2012},
  abstract  = {Suburethral slings as well as different meshes are widely used treating stress urinary incontinence and prolaps in women. With the development of MiniSlings and special meshes using less alloplastic material anchorage systems become more important to keep devices in place and to put some tension especially on the MiniSlings. To date, there are many different systems of MiniSlings of different companies on the market which differ in the structure of the used meshes and anchors. A new objective measurement method to compare different properties of MiniSling systems (mesh and anchor) is presented in this article. Ballistic gelatine acts as soft tissue surrogate. Significant differences in parameters like pull-out strength of anchors or shrinkage of meshes under loading conditions have been determined. The form and size of the anchors as well as the structural stability of the meshes are decisive for a proper integration. The tested anchorings sytems showed markedly different mechanical function at their respective load bearing capacity. As the stable fixation of the device in tissue is a prerequisite for a permanet reinforcement, the proposed test system permits further optimisation of anchor and mesh devices to improve the success of the surgical treatment},
  language  = {en}
}
@article{Staat2012,
  author    = {Staat, Manfred},
  title     = {Limit and shakedown analysis under uncertainty},
  series = {Tap chi Khoa hoc \& ung dung - Dai hoc Ton Duc Thang},
  volume    = {19},
  journal   = {Tap chi Khoa hoc \& ung dung - Dai hoc Ton Duc Thang},
  pages     = {45 -- 47},
  year      = {2012},
  language  = {en}
}
@article{SpelthahnSchubertSchoening2012,
  author    = {Spelthahn, Heiko and Schubert, J{\"u}rgen and Sch{\"o}ning, Michael Josef},
  title     = {D{\"u}nnschichtsensoren f{\"u}r die Schwermetallanalytik},
  series = {GIT : Labor-Fachzeitschrift},
  volume    = {56},
  journal   = {GIT : Labor-Fachzeitschrift},
  number    = {4},
  publisher = {Wiley-VCH},
  address   = {Weinheim},
  issn      = {0016-3538},
  pages     = {285 -- 287},
  year      = {2012},
  abstract  = {Die Detektion von Schadstoffen repr{\"a}sentiert in der Umweltanalytik eine wichtige Aufgabenstellung. Gerade die Abwasser- bzw. Brauchwasseranalytik sowie die Prozesskontrolle haben einen hohen Stellenwert. Siliziumbasierte D{\"u}nnschichtsensoren bieten eine kosteng{\"u}nstige M{\"o}glichkeit, „online"-Messungen bzw. Vor-Ort-Messungen zeitnah durchzuf{\"u}hren. In dieser Arbeit wird ein potentiometrisches Sensorarray auf der Basis von Chalkogenidgl{\"a}sern zur Detektion von Schwermetallen in w{\"a}ssrigen Medien vorgestellt.},
  language  = {en}
}
@article{SpelthahnSchubertSchoening2012,
  author    = {Spelthahn, Heiko and Schubert, J{\"u}rgen and Sch{\"o}ning, Michael Josef},
  title     = {D{\"u}nnschichtsensoren f{\"u}r die Schwermetallanalytik : Mikroelektroden auf Chalkogenidglasbasis},
  series = {GIT Labor-Fachzeitschrift},
  journal   = {GIT Labor-Fachzeitschrift},
  number    = {4},
  publisher = {Wiley-VCH},
  address   = {Weinheim},
  pages     = {285 -- 287},
  year      = {2012},
  abstract  = {Die Detektion von Schadstoffen repr{\"a}sentiert in der Umweltanalytik eine wichtige Aufgabenstellung. Gerade die Abwasser- bzw. Brauchwasseranalytik sowie die Prozesskontrolle haben einen hohen Stellenwert. Siliziumbasierte D{\"u}nnschichtsensoren bieten eine kosteng{\"u}nstige M{\"o}glichkeit, „online"-Messungen bzw. Vor-Ort-Messungen zeitnah durchzuf{\"u}hren. In dieser Arbeit wird ein potentiometrisches Sensorarray auf der Basis von Chalkogenidgl{\"a}sern zur Detektion von Schwermetallen in w{\"a}ssrigen Medien vorgestellt.},
  language  = {de}
}
@article{SpelthahnKirsanovLeginetal.2012,
  author    = {Spelthahn, Heiko and Kirsanov, Dmitry and Legin, Andrey and Osterrath, Thomas and Schubert, J{\"u}rgen and Zander, Willi and Sch{\"o}ning, Michael Josef},
  title     = {Development of a thin-film sensor array for analytical monitoring of heavy metals in aqueous solutions},
  series = {Physica Status Solidi (a)},
  volume    = {209},
  journal   = {Physica Status Solidi (a)},
  number    = {5},
  publisher = {Wiley-VCH},
  address   = {Weinheim},
  isbn      = {1862-6319},
  doi       = {10.1002/pssa.201100733},
  pages     = {885 -- 891},
  year      = {2012},
  abstract  = {In industrial processes there is a variety of heavy metals (e.g., copper, zinc, cadmium, and lead) in use for wires, coatings, paints, alloys, batteries, etc. Since the application of these transition metals for industry is inevitable, it is a vital task to develop proper analytical techniques for their monitoring at low activity levels, especially because most of these elements are acutely toxic for biological organisms. The determination of ions in solution by means of a simple and inexpensive sensor array is, therefore, a promising task. In this work, a sensor array with heavy metal-sensitive chalcogenide glass membranes for the simultaneous detection of the four ions Ag⁺, Cu2⁺, Cd2⁺, and Pb2⁺ in solution is realized. The results of the physical characterization by means of microscopy, profilometry, Rutherford backscattering spectroscopy (RBS), and scanning electron microscopy (SEM) as well as the electrochemical characterization by means of potentiometric measurements are presented. Additionally, the possibility to expand the sensor array by polymeric sensor membranes is discussed.},
  language  = {en}
}
@article{SchoeningBaecker2012,
  author    = {Sch{\"o}ning, Michael Josef and B{\"a}cker, Matthias},
  title     = {Chip-basierte Sensoren f{\"u}r die Biotechnik},
  volume    = {13},
  number    = {2},
  publisher = {BIOCOM},
  address   = {Berlin},
  issn      = {1611-0854},
  year      = {2012},
  language  = {de}
}
@article{SchoeningBiselliSelmeretal.2012,
  author    = {Sch{\"o}ning, Michael Josef and Biselli, Manfred and Selmer, Thorsten and {\"O}hlschl{\"a}ger, Peter and Baumann, Marcus and F{\"o}rster, Arnold and Poghossian, Arshak},
  title     = {Forschung „zwischen" den Disziplinen: das Institut f{\"u}r Nano- und Biotechnologien},
  series = {Analytik news : das Online-Labormagazin f{\"u}r Labor und Analytik},
  volume    = {Publ. online},
  journal   = {Analytik news : das Online-Labormagazin f{\"u}r Labor und Analytik},
  publisher = {Dr. Beyer Internet-Beratung},
  address   = {Ober-Ramstadt},
  pages     = {11 Seiten},
  year      = {2012},
  abstract  = {"Biologie trifft Mikroelektronik", das Motto des Instituts f{\"u}r Nano- und Biotechnologien (INB) an der FH Aachen, unterstreicht die zunehmende Bedeutung interdisziplin{\"a}r gepr{\"a}gter Forschungsaktivit{\"a}ten. Der thematische Zusammenschluss grundst{\"a}ndiger Disziplinen, wie die Physik, Elektrotechnik, Chemie, Biologie sowie die Materialwissenschaften, l{\"a}sst neue Forschungsgebiete entstehen, ein herausragendes Beispiel hierf{\"u}r ist die Nanotechnologie: Hier werden neue Werkstoffe und Materialien entwickelt, einzelne Nanopartikel oder Molek{\"u}le und deren Wechselwirkung untersucht oder Schichtstrukturen im Nanometerbereich aufgebaut, die neue und vorher nicht bekannte Eigenschaften hervorbringen. Vor diesem Hintergrund b{\"u}ndelt das im Jahre 2006 gegr{\"u}ndete INB die an der FH Aachen vorhandenen Kompetenzen von derzeit insgesamt sieben Laboratorien auf den Gebieten der Halbleitertechnik und Nanoelektronik, Nanostrukturen und DNA-Sensorik, der Chemo- und Biosensorik, der Enzymtechnologie, der Mikrobiologie und Pflanzenbiotechnologie, der Zellkulturtechnik, sowie der Roten Biotechnologie synergetisch. In der Nano- und Biotechnologie steckt außergew{\"o}hnliches Potenzial! Nicht zuletzt deshalb stellen sich die Forscher der Herausforderung, in diesem Bereich gemeinsam zu forschen und Schnittstellen zu nutzen, um so bei der Gestaltung neuartiger Ideen und Produkte mitzuwirken, die zuk{\"u}nftig unser allt{\"a}gliches Leben ver{\"a}ndern werden. Im Folgenden werden die verschiedenen Forschungsbereiche kurz zusammenfassend vorgestellt und vorhandene Interaktionen anhand von exemplarisch ausgew{\"a}hlten, aktuellen Forschungsprojekten skizziert.},
  language  = {de}
}
@article{SchusserPoghossianBaeckeretal.2012,
  author    = {Schusser, Sebastian and Poghossian, Arshak and B{\"a}cker, Matthias and Leinhos, Marcel and Wagner, Patrick and Sch{\"o}ning, Michael Josef},
  title     = {Characterization of biodegradable polymers with capacitive field-effect sensors},
  series = {Sensors and actuators B: Chemical},
  volume    = {187},
  journal   = {Sensors and actuators B: Chemical},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0925-4005},
  doi       = {10.1016/j.snb.2012.07.099},
  pages     = {2 -- 7},
  year      = {2012},
  abstract  = {In vitro studies of the degradation kinetic of biopolymers are essential for the design and optimization of implantable biomedical devices. In the presented work, a field-effect capacitive sensor has been applied for the real-time and in situ monitoring of degradation processes of biopolymers for the first time. The polymer-covered field-effect sensor is, in principle, capable to detect any changes in bulk, surface and interface properties of the polymer induced by degradation processes. The feasibility of this approach has been experimentally proven by using the commercially available biomedical polymer poly(D,L-lactic acid) (PDLLA) as a model system. PDLLA films of different thicknesses were deposited on the Ta₂O₅-gate surface of the field-effect structure from a polymer solution by means of spin-coating method. The polymer-modified field-effect sensors have been characterized by means of capacitance-voltage and impedance-spectroscopy method. The degradation of the PDLLA was accelerated by changing the degradation medium from neutral (pH 7.2) to alkaline (pH 9) condition, resulting in drastic changes in the capacitance and impedance spectra of the polymer-modified field-effect sensor.},
  language  = {en}
}
@article{SchubaHoefken2012,
  author    = {Schuba, Marko and H{\"o}fken, Hans},
  title     = {Backtrack5: Datensammlung und Reporterstellung f{\"u}r Pentester mit MagicTree / H{\"o}fken, Hans ; Schuba, Marko},
  series = {Hakin9. 73 (2012), H. 3},
  journal   = {Hakin9. 73 (2012), H. 3},
  publisher = {-},
  isbn      = {1733-7186},
  pages     = {12 -- 16},
  year      = {2012},
  language  = {de}
}
@article{SchubaHoefkenSchaefer2012,
  author    = {Schuba, Marko and H{\"o}fken, H. and Schaefer, T.},
  title     = {Smartphone Forensik},
  series = {Hakin9 : Practical Protection (2012)},
  journal   = {Hakin9 : Practical Protection (2012)},
  publisher = {-},
  isbn      = {1733-7186},
  pages     = {10 -- 20},
  year      = {2012},
  language  = {de}
}
@article{SchneiderSchneider2012,
  author    = {Schneider, Bettina and Schneider, Wilhelm},
  title     = {Externes Rechnungswesen nach BilMoG: Grundelemente und Aufbau},
  series = {Das Wirtschaftsstudium : wisu ; Zeitschrift f{\"u}r Ausbildung, Examen, Berufseinstieg und Fortbildung},
  volume    = {41},
  journal   = {Das Wirtschaftsstudium : wisu ; Zeitschrift f{\"u}r Ausbildung, Examen, Berufseinstieg und Fortbildung},
  number    = {3},
  publisher = {Lange},
  address   = {D{\"u}sseldorf},
  issn      = {0340-3084},
  pages     = {332 -- 337},
  year      = {2012},
  language  = {de}
}
@article{SchneiderSchneider2012,
  author    = {Schneider, Bettina and Schneider, Wilhelm},
  title     = {Due Diligence - Grundlagen und Checkliste f{\"u}r KMU},
  series = {Betriebswirtschaft im Blickpunkt},
  journal   = {Betriebswirtschaft im Blickpunkt},
  publisher = {IWW Institut f{\"u}r Wissen in der Wirtschaft},
  address   = {Nordkirchen},
  issn      = {2191-1118},
  pages     = {148 -- 149},
  year      = {2012},
  abstract  = {Im Folgenden sollen Anlass und Inhalt einer Due Diligence erl{\"a}utert werden. Im Rahmen einer Checkliste werden Beratern und Unternehmen Hinweise zu m{\"o}glichen Pr{\"u}fungsgebieten sowie zu vorzuhaltenden oder zu pr{\"u}fenden Unterlagen gegeben. Entstanden ist die Checkliste aus der langj{\"a}hrigen praktischen T{\"a}tigkeit der Autoren bei einer großen Wirtschaftspr{\"u}fungsgesellschaft bzw. einer deutschen Großbank.},
  language  = {de}
}
@article{SchneiderSchneider2012,
  author    = {Schneider, Bettina and Schneider, Wilhelm},
  title     = {Jahresabschluss nach BilMoG : Ansatz-, Ausweis- und Bewertungsvorschriften},
  series = {Das Wirtschaftsstudium : wisu ; Zeitschrift f{\"u}r Ausbildung, Examen, Berufseinstieg und Fortbildung},
  volume    = {41},
  journal   = {Das Wirtschaftsstudium : wisu ; Zeitschrift f{\"u}r Ausbildung, Examen, Berufseinstieg und Fortbildung},
  number    = {4},
  publisher = {Lange},
  address   = {D{\"u}sseldorf},
  issn      = {0340-3084},
  pages     = {529 -- 535},
  year      = {2012},
  language  = {de}
}
@article{SchneiderSchneider2012,
  author    = {Schneider, Bettina and Schneider, Wilhelm},
  title     = {Grundlagen der Unternehmensbesteuerung},
  series = {Das Wirtschaftsstudium : wisu ; Zeitschrift f{\"u}r Ausbildung, Examen, Berufseinstieg und Fortbildung},
  volume    = {41},
  journal   = {Das Wirtschaftsstudium : wisu ; Zeitschrift f{\"u}r Ausbildung, Examen, Berufseinstieg und Fortbildung},
  number    = {10},
  publisher = {Lange},
  address   = {D{\"u}sseldorf},
  issn      = {0340-3084},
  pages     = {1312 -- 1318},
  year      = {2012},
  language  = {de}
}
@article{SchmitzWeber2012,
  author    = {Schmitz, Philipp and Weber, Martin},
  title     = {Buying and selling behavior of individual investors in option-like securities},
  series = {Die Betriebswirtschaft : DBW},
  volume    = {72},
  journal   = {Die Betriebswirtschaft : DBW},
  number    = {5},
  publisher = {Sch{\"a}ffer-Poeschel},
  address   = {Stuttgart},
  issn      = {0342-7064},
  doi       = {10.2139/ssrn.2055088},
  pages     = {409 -- 426},
  year      = {2012},
  abstract  = {We analyze the trading behavior of individual investors in option-like securities, namely bankissued warrants, and thus expand the growing literature of investors behavior to a new kind of securities. A unique data set from a large German discount broker gives us the opportunity to analyze the trading behavior of 1,454 investors, making 89,958 transactions in 6,724 warrants on 397 underlyings. In different logit regression, we make use of the facts that investors can speculate on rising and falling prices of the underlying with call and put warrants and that we also have information about the stock portfolios of the investors. We report several facts about the trading behavior of individual investors in warrants that are consistent with the literature on the behavior of individual investors in the stock market. The warrant investors buy calls and sell puts if the price of the underlying has decreased over the past trading days and they sell calls and buy puts if the price of the underlying has increased. That means, the investors follow negative feedback trading strategies in all four trading categories observed. In addition, we find strong evidence for the disposition effect for call as well as put warrants, which is reversed in December. The trading behavior is also influenced if the underlying reaches some exceptionally prices, e.g. highs, lows or the strike price. We show that hedging, as one natural candidate to buy puts, does not play an important role in the market for bank-issued warrants.},
  language  = {en}
}
@article{SchifferFerreinLakemeyer2012,
  author    = {Schiffer, Stefan and Ferrein, Alexander and Lakemeyer, Gerhard},
  title     = {Caesar: an intelligent domestic service robot},
  series = {Intelligent service robotics},
  volume    = {5},
  journal   = {Intelligent service robotics},
  number    = {4},
  publisher = {Springer},
  address   = {Berlin},
  issn      = {1861-2776},
  doi       = {10.1007/s11370-012-0118-y},
  pages     = {259 -- 276},
  year      = {2012},
  abstract  = {In this paper we present CAESAR, an intelligent domestic service robot. In domestic settings for service robots complex tasks have to be accomplished. Those tasks benefit from deliberation, from robust action execution and from flexible methods for human-robot interaction that account for qualitative notions used in natural language as well as human fallibility. Our robot CAESAR deploys AI techniques on several levels of its system architecture. On the low-level side, system modules for localization or navigation make, for instance, use of path-planning methods, heuristic search, and Bayesian filters. For face recognition and human-machine interaction, random trees and well-known methods from natural language processing are deployed. For deliberation, we use the robot programming and plan language READYLOG, which was developed for the high-level control of agents and robots; it allows combining programming the behaviour using planning to find a course of action. READYLOG is a variant of the robot programming language Golog. We extended READYLOG to be able to cope with qualitative notions of space frequently used by humans, such as "near" and "far". This facilitates human-robot interaction by bridging the gap between human natural language and the numerical values needed by the robot. Further, we use READYLOG to increase the flexible interpretation of human commands with decision-theoretic planning. We give an overview of the different methods deployed in CAESAR and show the applicability of a system equipped with these AI techniques in domestic service robotics},
  language  = {en}
}
@article{ScheikSchleserReisgen2012,
  author    = {Scheik, Sven and Schleser, Markus and Reisgen, Uwe},
  title     = {Thermisches Direktf{\"u}gen von Metall und Kusntstoff: eine Alternative zur Klebtechnik},
  series = {Adh{\"a}sion : Kleben \& Dichten},
  volume    = {56},
  journal   = {Adh{\"a}sion : Kleben \& Dichten},
  number    = {11},
  publisher = {Springer Vieweg},
  address   = {Wiesbaden},
  issn      = {0001-8198 (E-Journal); 0001-8198 (Print)},
  doi       = {10.1007/s35145-012-0005-x},
  pages     = {36 -- 40},
  year      = {2012},
  abstract  = {Im Rahmen des Exzellenzclusters „Integrative Produktionstechnik f{\"u}r Hochlohnl{\"a}nder" der RWTHAachen University werden derzeit alternative Verfahren zur Herstellung von Metall/Kunststoff- Verbindungen untersucht. Eines davon ist das thermische Direktf{\"u}gen, das eine stoffschl{\"u}ssige Verbindung zwischen Kunststoff und Metall erm{\"o}glicht und ohne die Verwendung von Klebstoffen, Haftvermittlern oder mechanischen Verbindungshilfen auskommt.},
  language  = {de}
}
@article{ScheerKapelyukhRodeetal.2012,
  author    = {Scheer, Nico and Kapelyukh, Yury and Rode, Anja and Buechel, Sandra and Wolf, C. Roland},
  title     = {Generation and characterization of novel cytochrome P450 Cyp2c gene cluster knockout and CYP2C9 humanized mouse lines},
  series = {Molecular Pharmacology},
  volume    = {82},
  journal   = {Molecular Pharmacology},
  number    = {6},
  publisher = {ASPET},
  address   = {Bethesda, Md.},
  issn      = {1521-0111},
  doi       = {10.1124/mol.112.080036},
  pages     = {1022 -- 1029},
  year      = {2012},
  abstract  = {Compared with rodents and many other animal species, the human cytochrome P450 (P450) Cyp2c gene cluster varies significantly in the multiplicity of functional genes and in the substrate specificity of its enzymes. As a consequence, the use of wild-type animal models to predict the role of human CYP2C enzymes in drug metabolism and drug-drug interactions is limited. Within the human CYP2C cluster CYP2C9 is of particular importance, because it is one of the most abundant P450 enzymes in human liver, and it is involved in the metabolism of a wide variety of important drugs and environmental chemicals. To investigate the in vivo functions of cytochrome P450 Cyp2c genes and to establish a model for studying the functions of CYP2C9 in vivo, we have generated a mouse model with a deletion of the murine Cyp2c gene cluster and a corresponding humanized model expressing CYP2C9 specifically in the liver. Despite the high number of functional genes in the mouse Cyp2c cluster and the reported roles of some of these proteins in different biological processes, mice deleted for Cyp2c genes were viable and fertile but showed certain phenotypic alterations in the liver. The expression of CYP2C9 in the liver also resulted in viable animals active in the metabolism and disposition of a number of CYP2C9 substrates. These mouse lines provide a powerful tool for studying the role of Cyp2c genes and of CYP2C9 in particular in drug disposition and as a factor in drug-drug interaction.},
  language  = {en}
}
@article{ScheerKapelyukhMcEwanetal.2012,
  author    = {Scheer, Nico and Kapelyukh, Yury and McEwan, Jillian and Beuger, Vincent and Stanley, Lesley A. and Rode, Anja and Wolf, C. Roland},
  title     = {Modeling Human Cytochrome P450 2D6 Metabolism and Drug-drug Interaction by a Novel Panel of Knockout and Humanized Mouse Lines},
  series = {Molecular Pharmacology},
  volume    = {81},
  journal   = {Molecular Pharmacology},
  number    = {1},
  publisher = {ASPET},
  address   = {Bethesda, Md.},
  issn      = {1521-0111},
  doi       = {10.1124/mol.111.075192},
  pages     = {63 -- 72},
  year      = {2012},
  abstract  = {The highly polymorphic human cytochrome P450 2D6 enzyme is involved in the metabolism of up to 25\% of all marketed drugs and accounts for significant individual differences in response to CYP2D6 substrates. Because of the differences in the multiplicity and substrate specificity of CYP2D family members among species, it is difficult to predict pathways of human CYP2D6-dependent drug metabolism on the basis of animal studies. To create animal models that reflect the human situation more closely and that allow an in vivo assessment of the consequences of differential CYP2D6 drug metabolism, we have developed a novel straightforward approach to delete the entire murine Cyp2d gene cluster and replace it with allelic variants of human CYP2D6. By using this approach, we have generated mouse lines expressing the two frequent human protein isoforms CYP2D6.1 and CYP2D6.2 and an as yet undescribed variant of this enzyme, as well as a Cyp2d cluster knockout mouse. We demonstrate that the various transgenic mouse lines cover a wide spectrum of different human CYP2D6 metabolizer phenotypes. The novel humanization strategy described here provides a robust approach for the expression of different CYP2D6 allelic variants in transgenic mice and thus can help to evaluate potential CYP2D6-dependent interindividual differences in drug response in the context of personalized medicine.},
  language  = {en}
}
@article{ScheerBalimaneHaywardetal.2012,
  author    = {Scheer, Nico and Balimane, Praveen and Hayward, Michael D. and Buechel, Sandra and Kauselmann, Gunther and Wolf, C. Roland},
  title     = {Generation and Characterization of a Novel Multidrug Resistance Protein 2 Humanized Mouse Line},
  series = {Drug Metabolism and Disposition},
  volume    = {40},
  journal   = {Drug Metabolism and Disposition},
  number    = {11},
  publisher = {ASPET},
  address   = {Bethesda, Md.},
  issn      = {1521-0111},
  doi       = {10.1124/dmd.112.047605},
  pages     = {2212 -- 2218},
  year      = {2012},
  abstract  = {The multidrug resistance protein (MRP) 2 is predominantly expressed in liver, intestine, and kidney, where it plays an important role in the excretion of a range of drugs and their metabolites or endogenous compounds into bile, feces, and urine. Mrp knockout [Mrp2(-/-)] mice have been used recently to study the role of MRP2 in drug disposition. Here, we describe the first generation and initial characterization of a mouse line humanized for MRP2 (huMRP2), which is nulled for the mouse Mrp2 gene and expresses the human transporter in the organs and cell types where MRP2 is normally expressed. Analysis of the mRNA expression for selected cytochrome P450 and transporter genes revealed no major changes in huMRP2 mice compared with wild-type controls. We show that human MRP2 is able to compensate functionally for the loss of the mouse transporter as demonstrated by comparable bilirubin levels in the humanized mice and wild-type controls, in contrast to the hyperbilirubinemia phenotype that is observed in MRP2(-/-) mice. The huMRP2 mouse provides a model to study the role of the human transporter in drug disposition and in assessing the in vivo consequences of inhibiting this transporter by compounds interacting with human MRP2.},
  language  = {en}
}
@article{RostLind2012,
  author    = {Rost, Kathrin Dorothea and Lind, Thorsten Patric},
  title     = {Die Aufrechnung des Insolvenzverwalters gegen eine Insolvenzforderung nach ihrer Feststellung},
  series = {Zeitschrift f{\"u}r das gesamte Insolvenzrecht : ZInsO},
  journal   = {Zeitschrift f{\"u}r das gesamte Insolvenzrecht : ZInsO},
  publisher = {Heymanns},
  address   = {K{\"o}ln},
  issn      = {1615-8032},
  pages     = {2179 -- 2187},
  year      = {2012},
  language  = {de}
}
@article{RiglingElkinDobbertinetal.2012,
  author    = {Rigling, Andreas and Elkin, Ch{\´e} and Dobbertin, Matthias and Eilmann, Britta and Giuggiola, Arnaud and Wohlgemuth, Thomas and Bugmann, Harald},
  title     = {Wald und Klimawandel in der inneralpinen Trockenregion Visp},
  series = {Schweizerische Zeitschrift f{\"u}r Forstwesen},
  volume    = {163},
  journal   = {Schweizerische Zeitschrift f{\"u}r Forstwesen},
  number    = {12},
  publisher = {Schweizerischer Forstverein},
  address   = {Z{\"u}rich},
  issn      = {2235-1469 (Online)},
  doi       = {10.3188/szf.2012.0481},
  pages     = {481 -- 492},
  year      = {2012},
  abstract  = {Der Temperaturanstieg der vergangenen Jahrzehnte war in Gebirgsregionen besonders ausgepr{\"a}gt. Sollte sich dieser Temperaturtrend im 21. Jahrhundert fortsetzen, dann d{\"u}rf-ten sich auch die H{\"a}ufigkeit und Intensit{\"a}t von Niederschl{\"a}-gen und Trockenperioden ver{\"a}ndern, was die Waldwirtschaft vor grosse Herausforderungen stellen wird. Trockenheit ist ein entscheidender Faktor f{\"u}r die Wald{\"o}kosysteme der inner-alpinen T{\"a}ler, wo seit Jahren trockenheitsbedingtes Baum-sterben festgestellt wird. Der vorliegende Beitrag hat zum Ziel, die Sensitivit{\"a}t der verschiedenen Wald{\"o}kosysteme ge-gen{\"u}ber Klimawandel und alternative, teilweise extreme Bewirtschaftungsvarianten in der Region Visp zu testen. Me-thodische Ans{\"a}tze wie Monitoring, Feldexperimente und dy-namische Modellierung wurden kombiniert, und es wurden verschiedene {\"O}kosystemleistungen ber{\"u}cksichtigt, so Holz-produktion, Schutz vor Naturgefahren, Kohlenstoffspeiche-rung und Aspekte der Biodiversit{\"a}t. Die Resultate deuten da-rauf hin, dass auf den Trockenstandorten der Tieflagen die einheimischen Baumarten an ihre physiologischen Grenzen stossen und l{\"a}ngerfristig {\"u}ber alternative Baumarten nach-gedacht werden sollte. In den mittleren Lagen d{\"u}rften Tro-ckenheit und Schadinsekten wie die Borkenk{\"a}fer die zuk{\"u}nf-tige Waldentwicklung steuern. In den Hochlagen hingegen werden sich die W{\"a}lder ausdehnen und besser wachsen als heute. Alle untersuchten {\"O}kosystemleistungen werden ge-bietsweise starken Ver{\"a}nderungen unterworfen sein. Die dis-kutierten Bewirtschaftungsvarianten scheinen dazu geeignet, die Wasserverf{\"u}gbarkeit der Best{\"a}nde, haupts{\"a}chlich in tief-eren Lagen, zu erh{\"o}hen und dadurch die Widerstandskraft der B{\"a}ume gegen{\"u}ber Trockenperioden vor{\"u}bergehend zu st{\"a}rken. Es ist aber davon ausgehen, dass nur verh{\"a}ltnism{\"a}s-sig starke Eingriffe wesentliche Effekte erzielen k{\"o}nnen. Die Verkn{\"u}pfung von Umweltmonitoring, Feldexperimenten und Modellierung unter Miteinbezug von {\"O}kosystemleistungen ist vielversprechend, da sie eine differenzierte Absch{\"a}tzung des zuk{\"u}nftigen Landschaftswandels und seiner Effekte auf die Waldleistungen erm{\"o}glicht.},
  language  = {de}
}
@article{RiglingBiglerEilmannetal.2012,
  author    = {Rigling, Andreas and Bigler, Christof and Eilmann, Britta and Feldmeyer-Christe, Elisabeth and Gimmi, Urs and Ginzler, Christian and Graf, Ulrich and Mayer, Phillip and Vacchiano, Giorgio and Weber, Pascal and Wohlgemuth, Thomas and zweifel, Roman and Dobbertin, Matthias},
  title     = {Driving factors of a vegetation shift from Scots pine to pubescent oak in dry Alpine forests},
  series = {Global Change Biology},
  volume    = {19},
  journal   = {Global Change Biology},
  number    = {1},
  publisher = {Wiley-Blackwell},
  address   = {Oxford},
  issn      = {1354-1013 (Print)},
  doi       = {10.1111/gcb.12038},
  pages     = {229 -- 240},
  year      = {2012},
  abstract  = {An increasing number of studies have reported on forest declines and vegetation shifts triggered by drought. In the Swiss Rhone valley (Valais), one of the driest inner-Alpine regions, the species composition in low elevation forests is changing: The sub-boreal Scots pine (Pinus sylvestris L.) dominating the dry forests is showing high mortality rates. Concurrently the sub-Mediterranean pubescent oak (Quercus pubescens Willd.) has locally increased in abundance. However, it remains unclear whether this local change in species composition is part of a larger-scale vegetation shift. To study variability in mortality and regeneration in these dry forests we analysed data from the Swiss national forest inventory (NFI) on a regular grid between 1983 and 2003, and combined it with annual mortality data from a monitoring site. Pine mortality was found to be highest at low elevation (below 1000 m a.s.l.). Annual variation in pine mortality was correlated with a drought index computed for the summer months prior to observed tree death. A generalized linear mixed-effects model indicated for the NFI data increased pine mortality on dryer sites with high stand competition, particularly for small-diameter trees. Pine regeneration was low in comparison to its occurrence in the overstorey, whereas oak regeneration was comparably abundant. Although both species regenerated well at dry sites, pine regeneration was favoured at cooler sites at higher altitude and oak regeneration was more frequent at warmer sites, indicating a higher adaptation potential of oaks under future warming. Our results thus suggest that an extended shift in species composition is actually occurring in the pine forests in the Valais. The main driving factors are found to be climatic variability, particularly drought, and variability in stand structure and topography. Thus, pine forests at low elevations are developing into oak forests with unknown consequences for these ecosystems and their goods and services.},
  language  = {en}
}
@article{RibitschHeumannKarletal.2012,
  author    = {Ribitsch, D. and Heumann, S. and Karl, W. and Gerlach, J. and Leber, R. and Birner-Gruenberger, R. and Gruber, K. and Eiteljoerg, I. and Remler, P. and Siegert, Petra and Lange, J. and Maurer, Karl-Heinz and Berg, G. and Guebitz, G. M. and Schwab, H.},
  title     = {Extracellular serine proteases from Stenotrophomonas maltophilia: Screening, isolation and heterologous expression in E. coli},
  series = {Journal of biotechnology},
  volume    = {157},
  journal   = {Journal of biotechnology},
  number    = {1},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1873-4863 (E-Journal); 0168-1656 (Print)},
  doi       = {10.1016/j.jbiotec.2011.09.025},
  pages     = {140 -- 147},
  year      = {2012},
  abstract  = {A large strain collection comprising antagonistic bacteria was screened for novel detergent proteases. Several strains displayed protease activity on agar plates containing skim milk but were inactive in liquid media. Encapsulation of cells in alginate beads induced protease production. Stenotrophomonas maltophilia emerged as best performer under washing conditions. For identification of wash-active proteases, four extracellular serine proteases called StmPr1, StmPr2, StmPr3 and StmPr4 were cloned. StmPr2 and StmPr4 were sufficiently overexpressed in E. coli. Expression of StmPr1 and StmPr3 resulted in unprocessed, insoluble protein. Truncation of most of the C-terminal domain which has been identified by enzyme modeling succeeded in expression of soluble, active StmPr1 but failed in case of StmPr3. From laundry application tests StmPr2 turned out to be a highly wash-active protease at 45 °C. Specific activity of StmPr2 determined with suc-l-Ala-l-Ala-l-Pro-l-Phe-p-nitroanilide as the substrate was 17 ± 2 U/mg. In addition we determined the kinetic parameters and cleavage preferences of protease StmPr2.},
  language  = {en}
}
@article{ReisgenSchleserMokrovetal.2012,
  author    = {Reisgen, Uwe and Schleser, Markus and Mokrov, Oleg and Zabirov, Alexander and F{\"u}ssel, Uwe and Schnick, Michael and Hertel, Martin and Jaeckel, Sebastian},
  title     = {Modellierung und Visualisierung der MSG-Lichtbogenprozesse},
  series = {Schweissen und Schneiden : Fachzeitschrift f{\"u}r Schweißen und verwandte Verfahren},
  volume    = {64},
  journal   = {Schweissen und Schneiden : Fachzeitschrift f{\"u}r Schweißen und verwandte Verfahren},
  number    = {4},
  publisher = {DVS Verlag},
  address   = {D{\"u}sseldorf},
  issn      = {0036-7184},
  pages     = {166 -- 174},
  year      = {2012},
  language  = {de}
}
@article{ReisgenSchleserMokrovetal.2012,
  author    = {Reisgen, Uwe and Schleser, Markus and Mokrov, Oleg and Zabirov, Alexander and F{\"u}ssel, Uwe and Schnick, Michael and Hertel, Martin and Jaeckel, Sebastian},
  title     = {Modelling and visualisation of the GMA process},
  series = {Welding and Cutting},
  volume    = {11},
  journal   = {Welding and Cutting},
  number    = {4},
  publisher = {DVS Verlag},
  address   = {D{\"u}sseldorf},
  issn      = {1612-3433},
  pages     = {242 -- 249},
  year      = {2012},
  language  = {en}
}
@article{ReisgenSchleserMokrovetal.2012,
  author    = {Reisgen, Uwe and Schleser, Markus and Mokrov, Oleg and Ahmed, Essam},
  title     = {Statistical modeling of laser welding of DP/TRIP steel sheets},
  series = {Optics and laser technology},
  volume    = {44},
  journal   = {Optics and laser technology},
  number    = {1},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1879-2545 (E-Journal); 0030-3992 (Print); 0308-4280 (Print)},
  doi       = {10.1016/j.optlastec.2011.05.025},
  pages     = {92 -- 101},
  year      = {2012},
  abstract  = {In this research work, a statistical analysis of the CO2 laser beam welding of dual phase (DP600)/transformation induced plasticity (TRIP700) steel sheets was done using response surface methodology. The analysis considered the effect of laser power (2-2.2 kW), welding speed (40-50 mm/s) and focus position (-1 to 0 mm) on the heat input, the weld bead geometry, uniaxial tensile strength, formability limited dome height and welding operation cost. The experimental design was based on Box-Behnken design using linear and quadratic polynomial equations for predicting the mathematical models. The results indicate that the proposed models predict the responses adequately within the limits of welding parameters being used and the welding speed is the most significant parameter during the welding process.},
  language  = {en}
}
@article{ReisgenSchleserMokrovetal.2012,
  author    = {Reisgen, Uwe and Schleser, Markus and Mokrov, Oleg and Ahmed, Essam},
  title     = {Optimization of laser welding of DP/TRIP steel sheets using statistical approach},
  series = {Optics and laser technology},
  volume    = {44},
  journal   = {Optics and laser technology},
  number    = {1},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1879-2545 (E-Journal); 0030-3992 (Print); 0308-4280 (Print)},
  doi       = {10.1016/j.optlastec.2011.06.028},
  pages     = {255 -- 262},
  year      = {2012},
  abstract  = {Generally, the quality of a weld joint is directly influenced by the welding input parameter settings. Selection of proper process parameters is important to obtain the desired weld bead profile and quality. In this research work, numerical and graphical optimization techniques of the CO2 laser beam welding of dual phase (DP600)/transformation induced plasticity (TRIP700) steel sheets were carried out using response surface methodology (RSM) based on Box-Behnken design. The procedure was established to improve the weld quality, increase the productivity and minimize the total operation cost by considering the welding parameters range of laser power (2-2.2 kW), welding speed (40-50 mm/s) and focus position (-1 to 0 mm). It was found that, RSM can be considered as a powerful tool in experimental welding optimization, even when the experimenter does not have a model for the process. Strong, efficient and low cost weld joints could be achieved using the optimum welding conditions.},
  language  = {en}
}
@article{ReisgenSchleserAbdurakhmanovetal.2012,
  author    = {Reisgen, Uwe and Schleser, Markus and Abdurakhmanov, Aydemir and Turichin, Gleb and Valdaitseva, Elena and Bach, Friedrich-Wilhelm and Hassel, Thomas and Beniyashi, Alexander},
  title     = {Investigation of factors influencing the formation of weld defects in non-vacuum electron beam welding},
  series = {The Paton welding journal},
  volume    = {2012},
  journal   = {The Paton welding journal},
  number    = {2},
  publisher = {Paton Publishing House},
  address   = {Kiev},
  issn      = {0957-798X},
  pages     = {11 -- 18},
  year      = {2012},
  abstract  = {The influence of welding condition parameters and properties of material on formation of defects, such as humping and undercuts, in non-vacuum electron beam welding was investigated. The influence of separate welding parameters on the quality of welds was determined.},
  language  = {en}
}
@article{ReisgenSchleserAbdurakhmanovetal.2012,
  author    = {Reisgen, Uwe and Schleser, Markus and Abdurakhmanov, Aydemir and Gumenyuk, Andrey},
  title     = {Measuring of plasma properties induced by non-vacuum electron beam welding},
  series = {Physics of plasma},
  volume    = {19},
  journal   = {Physics of plasma},
  number    = {1},
  publisher = {AIP Publishing},
  address   = {Melville, NY},
  issn      = {1089-7674 (E-Journal); 1070-664X (Print)},
  doi       = {10.1063/1.3675874},
  pages     = {1 -- 7},
  year      = {2012},
  abstract  = {Electron beam plasma measurement was realised by means of DIABEAM system invented by ISF RWTH Aachen. The Langmuir probe method is used for measurement. The relative simplicity of the method and the possibility of dispersion of high power on the probe allow its application for the investigation of high-power electron beams. The key element of the method is a rotating thin tungsten wire, which intersects the beam transversely on its axis and collects part of the current by itself. The signals, which are registered in the DIABEAM as a voltage, were taken in the form of amplitude. The conversion of the probe current into the distribution along the beam radius was realised using the Abel's method. A voltage-current characteristic was built for the beam current. The local electron density as well as the electron temperature, the floating potential and the plasma potential were measured and calculated by means of this characteristic.},
  language  = {en}
}
@article{ReisgenOlschokJakobsetal.2012,
  author    = {Reisgen, Uwe and Olschok, Simon and Jakobs, Stefan and Schleser, Markus and Mokrov, Oleg and Rossiter, Eduardo},
  title     = {Laser beam submerged arc hybrid welding},
  series = {Physics procedia},
  volume    = {39},
  journal   = {Physics procedia},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1875-3892},
  doi       = {10.1016/j.phpro.2012.10.016},
  pages     = {75 -- 83},
  year      = {2012},
  abstract  = {The laser beam-submerged arc hybrid welding method originates from the knowledge that, with increasing penetration depth, the laser beam process has a tendency to pore formation in the lower weld regions. The coupling with the energy-efficient submerged-arc process improves degassing and reduces the tendency to pore formation. The high deposition rate of the SA process in combination with the laser beam process offers, providing the appropriate choice of weld preparation, the possibility of welding plates with a thickness larger than 20° mm in a single pass, and also of welding thicker plates with the double-sided single pass technique.},
  language  = {en}
}
@article{PoghossianWeilBaeckeretal.2012,
  author    = {Poghossian, Arshak and Weil, M. H. and B{\"a}cker, Matthias and Mayer, D. and Sch{\"o}ning, Michael Josef},
  title     = {Field-effect Devices Functionalised with Gold-Nanoparticle/Macromolecule Hybrids: New Opportunities for a Label-Free Biosensing},
  series = {Procedia Engineering},
  journal   = {Procedia Engineering},
  number    = {47},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1877-7058},
  doi       = {10.1016/j.proeng.2012.09.136},
  pages     = {273 -- 276},
  year      = {2012},
  abstract  = {Field-effect capacitive electrolyte-insulator-semiconductor (EIS) sensors functionalised with citrate-capped gold nanoparticles (AuNP) have been used for the electrostatic detection of macromolecules by their intrinsic molecular charge. The EIS sensor detects the charge changes in the AuNP/macromolecule hybrids induced by the adsorption or binding events. A feasibility of the proposed detection scheme has been exemplary demonstrated by realising EIS sensors for the detection of poly-D-lysine molecules.},
  language  = {en}
}
@article{PieperKlein2012,
  author    = {Pieper, Martin and Klein, Peter},
  title     = {Application of simple, periodic homogenization techniques to non-linear heat conduction problems in non-periodic, porous media},
  series = {Heat mass transfer},
  volume    = {48},
  journal   = {Heat mass transfer},
  number    = {2},
  publisher = {Springer},
  address   = {Berlin},
  issn      = {0947-7411},
  doi       = {10.1007/s00231-011-0879-4},
  pages     = {291 -- 300},
  year      = {2012},
  abstract  = {Often, detailed simulations of heat conduction in complicated, porous media have large runtimes. Then homogenization is a powerful tool to speed up the calculations by preserving accurate solutions at the same time. Unfortunately real structures are generally non-periodic, which requires unpractical, complicated homogenization techniques. We demonstrate in this paper, that the application of simple, periodic techniques to realistic media, that are just close to periodic, gives accurate, approximative solutions. In order to obtain effective parameters for the homogenized heat equation, we have to solve a so called "cell problem". In contrast to periodic structures it is not trivial to determine a suitable unit cell, which represents a non-periodic media. To overcome this problem, we give a rule of thumb on how to choose a good cell. Finally we demonstrate the efficiency of our method for virtually generated foams as well as real foams and compare these results to periodic structures.},
  language  = {en}
}
@article{PaulssenNgyugenKahlckeetal.2012,
  author    = {Paulßen, Elisabeth and Ngyugen, Hung Huy and Kahlcke, Nils and Deflon, Victor M. and Abram, Ulrich},
  title     = {Tricarbonyltechnetium(I) and -rhenium(I) complexes with N′-thiocarbamoylpicolylbenzamidines},
  series = {Polyhedron},
  volume    = {40},
  journal   = {Polyhedron},
  number    = {1},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0277-5387},
  doi       = {10.1016/j.poly.2012.04.008},
  pages     = {153 -- 158},
  year      = {2012},
  abstract  = {N,N-Dialkylamino(thiocarbonyl)-N′-picolylbenzamidines react with (NEt4)2[M(CO)3X3] (M = Re, X = Br; M = Tc, X = Cl) under formation of neutral [M(CO)3L] complexes in high yields. The monoanionic NNS ligands bind in a facial coordination mode and can readily be modified at the (CS)NR1R2 moiety. The complexes [99Tc(CO)3(LPyMor)] and [Re(CO)3(L)] (L = LPyMor, LPyEt) were characterized by X-ray diffraction. Reactions of [99mTc(CO)3(H2O)3]+ with the N′-thiocarbamoylpicolylbenzamidines give the corresponding 99mTc complexes. The ester group in HLPyCOOEt allows linkage between biomolecules and the metal core.},
  language  = {en}
}
@article{PaulssenKongArciszewskietal.2012,
  author    = {Paulßen, Elisabeth and Kong, Shushu and Arciszewski, Pawel and Wielbalck, Swantje and Abram, Ulrich},
  title     = {Aryl and NHC Compounds of Technetium and Rhenium},
  series = {Journal of the American Chemical Society},
  volume    = {134},
  journal   = {Journal of the American Chemical Society},
  number    = {22},
  publisher = {ACS Publications},
  address   = {Washington, DC},
  issn      = {1520-5126},
  doi       = {10.1021/ja3033718},
  pages     = {9118 -- 9121},
  year      = {2012},
  abstract  = {Air- and water-stable phenyl complexes with nitridotechnetium(V) cores can be prepared by straightforward procedures. [TcNPh2(PPh3)2] is formed by the reaction of [TcNCl2(PPh3)2] with PhLi. The analogous N-heterocyclic carbene (NHC) compound [TcNPh2(HLPh)2], where HLPh is 1,3,4-triphenyl-1,2,4-triazol-5-ylidene, is available from (NBu4)[TcNCl4] and HLPh or its methoxo-protected form. The latter compound allows the comparison of different Tc-C bonds within one compound. Surprisingly, the Tc chemistry with such NHCs does not resemble that of corresponding Re complexes, where CH activation and orthometalation dominate.},
  language  = {en}
}
@article{OrzadaMaderwaldPoseretal.2012,
  author    = {Orzada, S. and Maderwald, S. and Poser, B. A. and Johst, S. and Kannengiesser, S. and Ladd, M. E. and Bitz, Andreas},
  title     = {Time-interleaved acquisition of modes: an analysis of SAR and image contrast implications},
  series = {Magnetic Resonance in Medicine},
  volume    = {67},
  journal   = {Magnetic Resonance in Medicine},
  number    = {4},
  publisher = {Wiley-Liss},
  address   = {New York},
  issn      = {1522-2594},
  doi       = {10.1002/mrm.23081},
  pages     = {1033 -- 1041},
  year      = {2012},
  abstract  = {s the magnetic field strength and therefore the operational frequency in MRI are increased, the radiofrequency wavelength approaches the size of the human head/body, resulting in wave effects which cause signal decreases and dropouts. Especially, whole-body imaging at 7 T and higher is therefore challenging. Recently, an acquisition scheme called time-interleaved acquisition of modes has been proposed to tackle the inhomogeneity problems in high-field MRI. The basic premise is to excite two (or more) different Burn:x-wiley:07403194:media:MRM23081:tex2gif-stack-1 modes using static radiofrequency shimming in an interleaved acquisition, where the complementary radiofrequency patterns of the two modes can be exploited to improve overall signal homogeneity. In this work, the impact of time-interleaved acquisition of mode on image contrast as well as on time-averaged specific absorption rate is addressed in detail. Time-interleaved acquisition of mode is superior in Burn:x-wiley:07403194:media:MRM23081:tex2gif-stack-2 homogeneity compared with conventional radiofrequency shimming while being highly specific absorption rate efficient. Time-interleaved acquisition of modes can enable almost homogeneous high-field imaging throughout the entire field of view in PD, T2, and T2*-weighted imaging and, if a specified homogeneity criterion is met, in T1-weighted imaging as well.},
  language  = {en}
}
@article{OlbertzFahrig2012,
  author    = {Olbertz, Klaus and Fahrig, Stephan},
  title     = {Offshoring als Betriebs(teil){\"u}bergang gem{\"a}ß \S 613a BGB},
  series = {ZIP Zeitschrift f{\"u}r Wirtschaftsrecht},
  journal   = {ZIP Zeitschrift f{\"u}r Wirtschaftsrecht},
  number    = {42},
  publisher = {Verlag Dr. Otto Schmidt},
  address   = {K{\"o}ln},
  issn      = {0723-9416},
  pages     = {2045},
  year      = {2012},
  language  = {de}
}
@article{Olbertz2012,
  author    = {Olbertz, Klaus},
  title     = {{\"U}bergang von Leiharbeitnehmern bei {\"U}bertragung des Entleiherbetriebs - Entscheidung des EuGH zum Recht des Betriebs{\"u}bergangs},
  series = {NWB - Steuer- und Wirtschaftsrecht},
  journal   = {NWB - Steuer- und Wirtschaftsrecht},
  number    = {5},
  publisher = {NWB-Verlag},
  address   = {Herne},
  issn      = {1860-9449},
  pages     = {398 -- 403},
  year      = {2012},
  abstract  = {Wieder einmal hat eine Entscheidung des Europ{\"a}ischen Gerichtshofs (EuGH) das bisherige nationale Verst{\"a}ndnis zu einer Frage des Rechts des Betriebs{\"u}bergangs erheblich ins Wanken gebracht. Bisher entsprach es allgemeiner Auffassung, dass die Arbeitsverh{\"a}ltnisse von Zeit- bzw. Leiharbeitnehmern bei einem Betriebs(teil){\"u}bergang des die Leiharbeitnehmer entleihenden Betriebs nicht auf den Betriebserwerber {\"u}bergehen. Der EuGH hat in der Rechtssache Albron Catering mit Urteil vom 21.10.2010 jedoch entschieden, dass auch Leiharbeitnehmer von einem Betriebs(teil){\"u}bergang erfasst sein k{\"o}nnen. Folglich kann der Erwerber eines Betriebs oder Betriebsteils gem. \S 613a BGB zuk{\"u}nftig verpflichtet sein, auch die an den Betriebsver{\"a}ußerer verliehenen Leiharbeitnehmer zu {\"u}bernehmen. Die Entscheidung des EuGH hat somit zur Konsequenz, dass der {\"U}bergang von Leiharbeitsverh{\"a}ltnissen auf den Erwerber eines Betriebs jedenfalls nicht mehr pauschal ausgeschlossen werden kann. Dies gilt es bei k{\"u}nftigen Betriebs(teil){\"u}bertragungen zu ber{\"u}cksichtigen, um unliebsame {\"U}berraschungen zu vermeiden.},
  language  = {de}
}
@article{OlaruKowalskiSethietal.2012,
  author    = {Olaru, Alexandra Maria and Kowalski, Julia and Sethi, Vaishali and Bl{\"u}mich, Bernhard},
  title     = {Exchange relaxometry of flow at small P{\´e}clet numbers in a glass bead pack},
  series = {Journal of Magnetic Resonance (JMR)},
  volume    = {220},
  journal   = {Journal of Magnetic Resonance (JMR)},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1096-0856},
  doi       = {10.1016/j.jmr.2012.04.015},
  pages     = {32 -- 44},
  year      = {2012},
  abstract  = {In this paper we consider low P{\´e}clet number flow in bead packs. A series of relaxation exchange experiments has been conducted and evaluated by ILT analysis. In the resulting correlation maps, we observed a collapse of the signal and a translation towards smaller relaxation times with increasing flow rates, as well as a signal tilt with respect to the diagonal. In the discussion of the phenomena we present a mathematical theory for relaxation exchange experiments that considers both diffusive and advective transport. We perform simulations based on this theory and discuss them with respect to the conducted experiments.},
  language  = {en}
}
@article{OertelBung2012,
  author    = {Oertel, Mario and Bung, Daniel B.},
  title     = {Initial stage of two-dimensional dam-break waves: laboratory versus VOF},
  series = {Journal of hydraulic research},
  volume    = {50},
  journal   = {Journal of hydraulic research},
  number    = {1},
  publisher = {Taylor \& Francis},
  address   = {London},
  issn      = {1814-2079 (E-Journal); 0022-1686 (Print)},
  doi       = {10.1080/00221686.2011.639981},
  pages     = {89 -- 97},
  year      = {2012},
  abstract  = {Since several decades, dam-break waves have been of main research interest. Mathematical approaches have been developed by analytical, physical and numerical models within the past 120 years. During the past 10 years, the number of research investigations has increased due to improved measurement techniques as well as significantly increased computer memories and performances. In this context, the present research deals with the initial stage of two-dimensional dam-break waves by comparing physical and numerical model results as well as analytical approaches. High-speed images and resulting particle image velocimetry calculations are thereby compared with the numerical volume-of-fluid (VOF) method, included in the commercial code FLOW-3D. Wave profiles and drag forces on placed obstacles are analysed in detail. Generally, a good agreement between the laboratory and VOF results is found.},
  language  = {en}
}
@article{NovacekTranKlingeetal.2012,
  author    = {Novacek, V. and Tran, Thanh Ngoc and Klinge, U. and Tolba, R. H. and Staat, Manfred and Bronson, D. G. and Miesse, A. M. and Whiffen, J. and Turquier, F.},
  title     = {Finite element modelling of stapled colorectal end-to-end anastomosis : Advantages of variable height stapler design},
  series = {Journal of Biomechanics},
  volume    = {45},
  journal   = {Journal of Biomechanics},
  number    = {115},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1873-2380},
  doi       = {10.1016/j.jbiomech.2012.07.021},
  pages     = {2693 -- 2697},
  year      = {2012},
  abstract  = {The impact of surgical staplers on tissues has been studied mostly in an empirical manner. In this paper, finite element method was used to clarify the mechanics of tissue stapling and associated phenomena. Various stapling modalities and several designs of circular staplers were investigated to evaluate the impact of the device on tissues and mechanical performance of the end-to-end colorectal anastomosis. Numerical simulations demonstrated that a single row of staples is not adequate to resist leakage due to non-linear buckling and opening of the tissue layers between two adjacent staples. Compared to the single staple row configuration, significant increase in stress experienced by the tissue at the inner staple rows was observed in two and three rows designs. On the other hand, adding second and/or third staple row had no effect on strain in the tissue inside the staples. Variable height design with higher staples in outer rows significantly reduced the stresses and strains in outer rows when compared to the same configuration with flat cartridge.},
  language  = {en}
}
@article{NomdedeuWillenSchiefferetal.2012,
  author    = {Nomdedeu, Mar Monsonis and Willen, Christine and Schieffer, Andre and Arndt, Hartmut},
  title     = {Temperature-dependent ranges of coexistence in a model of a two-prey-one-predator microbial food web},
  series = {Marine Biology},
  volume    = {159},
  journal   = {Marine Biology},
  number    = {11},
  publisher = {Springer},
  address   = {Berlin},
  issn      = {1432-1793},
  doi       = {10.1007/s00227-012-1966-x},
  pages     = {2423 -- 2430},
  year      = {2012},
  abstract  = {The objective of our study was to analyze the effects of temperature on the population dynamics of a three-species food web consisting of two prey bacteria (Pedobacter sp. and Acinetobacter johnsonii) and a protozoan predator (Tetrahymena pyriformis) as model organisms. We assessed the effects of temperature on the growth rates of all three species with the objective of developing a model with four differential equations based on the experimental data. The following hypotheses were tested at a theoretical level: Firstly, temperature changes can affect the dynamic behavior of a system by temperature-dependent parameters and interactions and secondly, food web response to temperature cannot be derived from the single species temperature response. The main outcome of the study is that temperature changes affect the parameter range where coexistence is possible within all three species. This has significant consequences on our ideas regarding the evaluation of effects of global warming.},
  language  = {en}
}
@article{NguyenDuongTranetal.2012,
  author    = {Nguyen, Nhu Huynh and Duong, Minh Tuan and Tran, Thanh Ngoc and Pham, Phu Tinh and Grottke, O. and Tolba, R. and Staat, Manfred},
  title     = {Influence of a freeze-thaw cycle on the stress-stretch curves of tissues of porcine abdominal organs},
  series = {Journal of Biomechanics},
  volume    = {45},
  journal   = {Journal of Biomechanics},
  number    = {14},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1873-2380},
  doi       = {10.1016/j.jbiomech.2012.07.008},
  pages     = {2382 -- 2386},
  year      = {2012},
  abstract  = {The paper investigates both fresh porcine spleen and liver and the possible decomposition of these organs under a freeze-thaw cycle. The effect of tissue preservation condition is an important factor which should be taken into account for protracted biomechanical tests. In this work, tension tests were conducted for a large number of tissue specimens from twenty pigs divided into two groups of 10. Concretely, the first group was tested in fresh state; the other one was tested after a freeze-thaw cycle which simulates the conservation conditions before biomechanical experiments. A modified Fung model for isotropic behavior was adopted for the curve fitting of each kind of tissues. Experimental results show strong effects of the realistic freeze-thaw cycle on the capsule of elastin-rich spleen but negligible effects on the liver which virtually contains no elastin. This different behavior could be explained by the autolysis of elastin by elastolytic enzymes during the warmer period after thawing. Realistic biomechanical properties of elastin-rich organs can only be expected if really fresh tissue is tested. The observations are supported by tests of intestines.},
  language  = {en}
}
@article{MuribTranCeunincketal.2012,
  author    = {Murib, Mohammed S. and Tran, Anh Quang and Ceuninck, Ward de and Sch{\"o}ning, Michael Josef and Nesladek, Milos and Serpeng{\"u}zel, Ali and Wagner, Patrick},
  title     = {Analysis of an optical biosensor based on elastic light scattering from diamond-, glass-, and sapphire microspheres},
  series = {Physica Status Solidi A},
  volume    = {209},
  journal   = {Physica Status Solidi A},
  number    = {9},
  publisher = {Wiley-VCH},
  address   = {Weinheim},
  issn      = {1862-6319},
  doi       = {10.1002/pssa.201100795},
  pages     = {1804 -- 1810},
  year      = {2012},
  abstract  = {Deoxyribonucleic acid (DNA) and protein recognition are now standard tools in biology. In addition, the special optical properties of microsphere resonators expressed by the high quality factor (Q-factor) of whispering gallery modes (WGMs) or morphology dependent resonances (MDRs) have attracted the attention of the biophotonic community. Microsphere-based biosensors are considered as powerful candidates to achieve label-free recognition of single molecules due to the high sensitivity of their WGMs. When the microsphere surface is modified with biomolecules, the effective refractive index and the effective size of the microsphere change resulting in a resonant wavelength shift. The transverse electric (TE) and the transverse magnetic (TM) elastic light scattering intensity of electromagnetic waves at 600 and 1400 nm are numerically calculated for DNA and unspecific binding of proteins to the microsphere surface. The effect of changing the optical properties was studied for diamond (refractive index 2.34), glass (refractive index 1.50), and sapphire (refractive index 1.75) microspheres with a 50 µm radius. The mode spacing, the linewidth of WGMs, and the shift of resonant wavelength due to the change in radius and refractive index, were analyzed by numerical simulations. Preliminary results of unspecific binding of biomolecules are presented. The calculated shift in WGMs can be used for biomolecules detection.},
  language  = {en}
}
@article{MottaghyDijkshoorn2012,
  author    = {Mottaghy, Darius and Dijkshoorn, Lydia},
  title     = {Implementing an effective finite difference formulation for borehole heat exchangers into a heat and mass transport code},
  series = {Renewable Energy},
  volume    = {45},
  journal   = {Renewable Energy},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0960-1481},
  doi       = {10.1016/j.renene.2012.02.013},
  pages     = {59 -- 71},
  year      = {2012},
  abstract  = {We present an effective finite difference formulation for implementing and modeling multiple borehole heat exchangers (BHE) in the general 3-D coupled heat and flow transport code SHEMAT. The BHE with arbitrary length can be either coaxial or double U-shaped. It is particularly suitable for modeling deep BHEs which contain varying pipe diameters and materials. Usually, in numerical simulations, a fine discretization of the BHE assemblage is required, due to the large geometric aspect ratios involved. This yields large models and long simulation times. The approach avoids this problem by considering heat transport between fluid and the soil through pipes and grout via thermal resistances. Therefore, the simulation time can be significantly reduced. The coupling with SHEMAT is realized by introducing an effective heat generation. Due to this connection, it is possible to consider heterogeneous geological models, as well as the influence of groundwater flow. This is particularly interesting when studying the long term behavior of a single BHE or a BHE field. Heating and cooling loads can enter the model with an arbitrary interval, e.g. from hourly to monthly values. When dealing with large BHE fields, computing times can be further significantly reduced by focusing on the temperature field around the BHEs, without explicitly modeling inlet and outlet temperatures. This allows to determine the possible migration of cold and warm plumes due to groundwater flow, which is of particular importance in urban areas with a high BHE installation density. The model is validated against the existing BHE modeling codes EWS and EED. A comparison with monitoring data from a deep BHE in Switzerland shows a good agreement. Synthetic examples demonstrate the field of application of this model.},
  language  = {en}
}
@article{MiyamotoKanekoMatsuoetal.2012,
  author    = {Miyamoto, Ko-ichiro and Kaneko, Kazumi and Matsuo, Akira and Wagner, Torsten and Kanoh, Shin{\´i}chiro and Sch{\"o}ning, Michael Josef and Yoshinobu, Tatsuo},
  title     = {Miniaturized chemical imaging sensor system using an OLED display panel},
  series = {Sensors and Actuators B: Chemical},
  volume    = {170},
  journal   = {Sensors and Actuators B: Chemical},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0925-4005},
  doi       = {10.1016/j.snb.2011.02.029},
  pages     = {82 -- 87},
  year      = {2012},
  abstract  = {The chemical imaging sensor is a semiconductor-based chemical sensor that can visualize the two-dimensional distribution of specific ions or molecules in the solution. In this study, we developed a miniaturized chemical imaging sensor system with an OLED display panel as a light source that scans the sensor plate. In the proposed configuration, the display panel is placed directly below the sensor plate and illuminates the back surface. The measured area defined by illumination can be arbitrarily customized to fit the size and the shape of the sample to be measured. The waveform of the generated photocurrent, the current-voltage characteristics and the pH sensitivity were investigated and pH imaging with this miniaturized system was demonstrated.},
  language  = {en}
}
@article{MiyamotoIchimuraWagneretal.2012,
  author    = {Miyamoto, K. and Ichimura, H. and Wagner, Torsten and Yoshinobu, T. and Sch{\"o}ning, Michael Josef},
  title     = {Chemical Imaging of ion Diffusion in a Microfluidic Channel},
  series = {Procedia Engineering},
  journal   = {Procedia Engineering},
  number    = {47},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1877-7058},
  doi       = {10.1016/j.proeng.2012.09.289},
  pages     = {886 -- 889},
  year      = {2012},
  abstract  = {The chemical imaging sensor is a chemical sensor which is capable of visualizing the spatial distribution of chemical species in sample solution. In this study, a novel measurement system based on the chemical imaging sensor was developed to observe the inside of a Y-shaped microfluidic channel while injecting two sample solutions from two branches. From the collected chemical images, it was clearly observed that the injected solutions formed laminar flows in the microfluidic channel. In addition, ion diffusion across the laminar flows was observed. This label-free method can acquire quantitative data of ion distribution and diffusion in microfluidic devices, which can be used to determine the diffusion coefficients, and therefore, the molecular weights of chemical species in the sample solution.},
  language  = {en}
}
@article{MartiusMischke2012,
  author    = {Martius, Alexander and Mischke, Winfried},
  title     = {Die Vernehmung des Wohnungseigent{\"u}mers : wann ist der Wohnungseigent{\"u}mer als Partei, wann als Zeuge zu vernehmen?},
  series = {Zeitschrift f{\"u}r die Anwaltspraxis : ZAP},
  journal   = {Zeitschrift f{\"u}r die Anwaltspraxis : ZAP},
  number    = {Fach 7},
  publisher = {ZAP Verlag},
  address   = {Bonn},
  issn      = {0936-7292},
  pages     = {431 -- 434},
  year      = {2012},
  language  = {de}
}
@article{MansurovDigelBiisenbaevetal.2012,
  author    = {Mansurov, Z. and Digel, Ilya and Biisenbaev, M. and Savistkaya, I. and Kistaubaeva, A. and Akimbekov, N. and Zhubanova, A.},
  title     = {Bio-composite material on the basis of carbonized rice husk in biomedicine and environmental applications},
  series = {Eurasian Chemico-Technological Journal},
  volume    = {14},
  journal   = {Eurasian Chemico-Technological Journal},
  number    = {2},
  publisher = {Institute of Combustion Problems},
  address   = {Almaty},
  issn      = {2522-4867},
  doi       = {10.18321/ectj105},
  pages     = {115 -- 131},
  year      = {2012},
  language  = {en}
}
@article{LustfeldPithanReissel2012,
  author    = {Lustfeld, H. and Pithan, C. and Reißel, Martin},
  title     = {Metallic electrolyte composites in the framework of the brick-layer model},
  series = {Journal of the European Ceramic Society},
  volume    = {32},
  journal   = {Journal of the European Ceramic Society},
  number    = {4},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0955-2219},
  doi       = {10.1016/j.jeurceramsoc.2011.10.017},
  pages     = {859 -- 864},
  year      = {2012},
  abstract  = {It is well known that the already large dielectric constants of some electrolytes like BaTiO₃ can be enhanced further by adding metallic (e.g. Ni, Cu or Ag) nanoparticles. The enhancement can be quite large, a factor of more than 1000 is possible. The consequences for the properties will be discussed in the present paper applying a brick-layer model (BLM) for calculating dc-resistivities of thin layers and a modified one (PBLM) that includes percolation for calculating dielectric properties of these materials. The PBLM results in an at least qualitative description and understanding of the physical phenomena: This model gives an explanation for the steep increase of the dielectric constant below the percolation threshold and why this increase is connected to a dramatic decrease of the breakdown voltage as well as the ability of storing electrical energy. We conclude that metallic electrolyte composites like BaTiO₃ are not appropriate for energy storage.},
  language  = {en}
}
@article{LoebSchartnerDachwaldetal.2012,
  author    = {Loeb, Horst Wolfgang and Schartner, Karl-Heinz and Dachwald, Bernd and Ohndorf, Andreas and Seboldt, Wolfgang},
  title     = {Interstellar heliopause probe},
  series = {Труды МАИ},
  journal   = {Труды МАИ},
  number    = {60},
  publisher = {Moskauer Staatliches Luftfahrtinstitut (МАИ)},
  address   = {Moskau},
  pages     = {2 -- 2},
  year      = {2012},
  abstract  = {There is common agreement within the scientific community that in order to understand our local galactic environment it will be necessary to send a spacecraft into the region beyond the solar wind termination shock. Considering distances of 200 AU for a new mission, one needs a spacecraft traveling at a speed of close to 10 AU/yr in order to keep the mission duration in the range of less than 25 yrs, a transfer time postulated by European Space Agency (ESA). Two propulsion options for the mission have been proposed and discussed so far: the solar sail propulsion and the ballistic/radioisotope-electric propulsion (REP). As a further alternative, we here investigate a combination of solar-electric propulsion (SEP) and REP. The SEP stage consists of six 22-cms diameter RIT-22 ion thrusters working with a high specific impulse of 7377 s corresponding to a positive grid voltage of 5 kV. Solar power of 53 kW at begin of mission (BOM) is provided by a lightweight solar array.},
  language  = {en}
}
@article{Lind2012,
  author    = {Lind, Thorsten Patric},
  title     = {Zur Rechtsscheinhaftung bei Handeln einer Unternehmergesellschaft unter dem Rechtsformzusatz „GmbH" : Urteil vom 12.06.2012 - II ZR 256/11 : Anmerkung},
  series = {Fachdienst Zivilrecht - LMK - Kommentierte BGH-Rechtsprechung, Lindenmaier-M{\"o}hring},
  journal   = {Fachdienst Zivilrecht - LMK - Kommentierte BGH-Rechtsprechung, Lindenmaier-M{\"o}hring},
  number    = {Ausg. 11},
  publisher = {Beck},
  address   = {M{\"u}nchen},
  issn      = {1611-1095},
  pages     = {339268},
  year      = {2012},
  language  = {de}
}
@article{Lind2012,
  author    = {Lind, Thorsten Patric},
  title     = {Rechtsprobleme bei der Liquidation der GmbH und der Gewinnaussch{\"u}ttung trotz bestehenden Anspruchs gegen den Gesellschafter : BGH, Urteil vom 23.04.2012 - II ZR 252/10 : Anmerkung},
  series = {Fachdienst Zivilrecht - LMK - Kommentierte BGH-Rechtsprechung, Lindenmaier-M{\"o}hring},
  journal   = {Fachdienst Zivilrecht - LMK - Kommentierte BGH-Rechtsprechung, Lindenmaier-M{\"o}hring},
  number    = {Ausg. 10},
  publisher = {Beck},
  address   = {M{\"u}nchen},
  issn      = {1611-1095},
  pages     = {338415},
  year      = {2012},
  language  = {de}
}
@article{Lind2012,
  author    = {Lind, Thorsten Patric},
  title     = {Vollzug der Schenkung einer Unterbeteiligung : BGH, Urteil vom 29.11.2011 - II ZR 306/09 : Anmerkung},
  series = {Fachdienst Zivilrecht - LMK - Kommentierte BGH-Rechtsprechung, Lindenmaier-M{\"o}hring},
  journal   = {Fachdienst Zivilrecht - LMK - Kommentierte BGH-Rechtsprechung, Lindenmaier-M{\"o}hring},
  number    = {Ausg. 4},
  publisher = {Beck},
  address   = {M{\"u}nchen},
  issn      = {1611-1095},
  pages     = {330150},
  year      = {2012},
  language  = {de}
}
@article{Lind2012,
  author    = {Lind, Thorsten Patric},
  title     = {Die Kostentragungspflicht bei der Aussonderung von Gegenst{\"a}nden, insbesondere bei Aufwendungen f{\"u}r den Ausbau einer Sache},
  series = {Insb{\"u}ro : Zeitschrift f{\"u}r Insolvenzsachbearbeitung und Entschuldungsverfahren},
  journal   = {Insb{\"u}ro : Zeitschrift f{\"u}r Insolvenzsachbearbeitung und Entschuldungsverfahren},
  number    = {H. 3},
  publisher = {Wolters Kluwer},
  address   = {K{\"o}ln},
  issn      = {1863-0731},
  pages     = {88 -- 89},
  year      = {2012},
  language  = {de}
}
@article{LeursMezoOehlschlaegeretal.2012,
  author    = {Leurs, Ulrike and Mezo, Gabor and {\"O}hlschl{\"a}ger, Peter and Orban, Erika and Marquard, Andrea and Manea, Marilena},
  title     = {Design, synthesis, in vitro stability and cytostatic effect of multifunctional anticancer drug-bioconjugates containing GnRH-III as a targeting moiety},
  series = {Peptide Science},
  volume    = {98},
  journal   = {Peptide Science},
  number    = {1},
  publisher = {Wiley},
  address   = {New York, NY},
  issn      = {1097-0282},
  doi       = {10.1002/bip.21640},
  pages     = {1 -- 10},
  year      = {2012},
  abstract  = {Bioconjugates containing the GnRH-III hormone decapeptide as a targeting moiety are able to deliver chemotherapeutic agents specifically to cancer cells expressing GnRH receptors, thereby increasing their local efficacy while limiting the peripheral toxicity. However, the number of GnRH receptors on cancer cells is limited and they desensitize under continuous hormone treatment. A possible approach to increase the receptor mediated tumor targeting and consequently the cytostatic effect of the bioconjugates would be the attachment of more than one chemotherapeutic agent to one GnRH-III molecule. Here we report on the design, synthesis and biochemical characterization of multifunctional bioconjugates containing GnRH-III as a targeting moiety and daunorubicin as a chemotherapeutic agent. Two different drug design approaches were pursued. The first one was based on the bifunctional [4Lys]-GnRH-III (Glp-His-Trp-Lys-His-Asp-Trp-Lys-Pro-Gly-NH2) containing two lysine residues in positions 4 and 8, whose ϵ-amino groups were used for the coupling of daunorubicin. In the second drug design, the native GnRH-III (Glp-His-Trp-Ser-His-Asp-Trp-Lys-Pro-Gly-NH2) was used as a scaffold; an additional lysine residue was coupled to the ϵ-amino group of 8Lys in order to generate two free amino groups available for conjugation of daunorubicin. The in vitro stability/degradation of all synthesized compounds was investigated in human serum, as well as in the presence of rat liver lysosomal homogenate. Their cellular uptake was determined on human breast cancer cells and the cytostatic effect was evaluated on human breast, colon and prostate cancer cell lines. Compared with a monofunctional compound, both drug design approaches resulted in multifunctional bioconjugates with increased cytostatic effect.},
  language  = {en}
}
@article{LempiaeinenCouttetBolognanietal.2012,
  author    = {Lempi{\"a}inen, Harri and Couttet, Philippe and Bolognani, Federico and M{\"u}ller, Arne and Dubost, Val{\´e}rie and Luisier, Rapha{\"e}lle and Rio-Espinola, Alberto del and Vitry, Veronique and Unterberger, Elif B. and Thomson, John P. and Treindl, Fridolin and Metzger, Ute and Wrzodek, Clemens and Hahne, Florian and Zollinger, Tulipan and Brasa, Sarah and Kalteis, Magdalena and Marcellin, Magali and Giudicelli, Fanny and Braeuning, Albert and Morawiec, Laurent and Zamurovic, Natasa and L{\"a}ngle, Ulrich and Scheer, Nico and Sch{\"u}beler, Dirk and Goodman, Jay and Chibout, Salah-Dine and Marlowe, Jennifer and Theil, Dietlinde and Heard, David J. and Grenet, Olivier and Zell, Andreas and Templin, Markus F. and Meehan, Richard R. and Wolf, Roland C. and Elcombe, Clifford R. and Schwarz, Michael and Moulin, Pierre and Terranova, R{\´e}mi and Moggs, Jonathan G.},
  title     = {Identification of Dlk1-Dio3 imprinted gene cluster non-coding RNAs as novel candidate biomarkers for liver tumor promotion},
  series = {Toxicological Sciences},
  volume    = {131},
  journal   = {Toxicological Sciences},
  number    = {2},
  publisher = {Oxford University Press},
  address   = {Oxford},
  issn      = {1094-2025},
  doi       = {10.1093/toxsci/kfs303},
  pages     = {375 -- 386},
  year      = {2012},
  abstract  = {The molecular events during nongenotoxic carcinogenesis and their temporal order are poorly understood but thought to include long-lasting perturbations of gene expression. Here, we have investigated the temporal sequence of molecular and pathological perturbations at early stages of phenobarbital (PB) mediated liver tumor promotion in vivo. Molecular profiling (mRNA, microRNA [miRNA], DNA methylation, and proteins) of mouse liver during 13 weeks of PB treatment revealed progressive increases in hepatic expression of long noncoding RNAs and miRNAs originating from the Dlk1-Dio3 imprinted gene cluster, a locus that has recently been associated with stem cell pluripotency in mice and various neoplasms in humans. PB induction of the Dlk1-Dio3 cluster noncoding RNA (ncRNA) Meg3 was localized to glutamine synthetase-positive hypertrophic perivenous hepatocytes, sug- gesting a role for β-catenin signaling in the dysregulation of Dlk1-Dio3 ncRNAs. The carcinogenic relevance of Dlk1-Dio3 locus ncRNA induction was further supported by in vivo genetic dependence on constitutive androstane receptor and β-catenin pathways. Our data identify Dlk1-Dio3 ncRNAs as novel candidate early biomarkers for mouse liver tumor promotion and provide new opportunities for assessing the carcinogenic potential of novel compounds.},
  language  = {en}
}
@article{LeidingerNoistenWollert2012,
  author    = {Leidinger, Rafael and Noisten, Thomas and Wollert, J{\"o}rg},
  title     = {Realtime automation networks in moVing industrial environments},
  series = {Journal of systemics, cybernetics and informatics},
  volume    = {Vol. 10},
  journal   = {Journal of systemics, cybernetics and informatics},
  number    = {Iss. 2},
  publisher = {IIIC},
  address   = {Orlando},
  issn      = {1690-4532},
  pages     = {52 -- 56},
  year      = {2012},
  abstract  = {The radio-based wireless data communication has made the realization of new technical solutions possible in many fields of the automation technology (AT). For about ten years, a constant disproportionate growth of wireless technologies can be observed in the automation technology. However, it shows that especially for the AT, conventional technologies of office automation are unsuitable and/or not manageable. The employment of mobile services in the industrial automation technology has the potential of significant cost and time savings. This leads to an increased productivity in various fields of the AT, for example in the factory and process automation or in production logistics. In this paper technologies and solutions for an automation-suited supply of mobile wireless services will be introduced under the criteria of real time suitability, IT-security and service orientation. Emphasis will be put on the investigation and development of wireless convergence layers for different radio technologies, on the central provision of support services for an easy-to-use, central, backup enabled management of combined wired / wireless networks and on the study on integrability in a Profinet real-time Ethernet network.},
  language  = {en}
}
@article{LaumannMainz2012,
  author    = {Laumann, J{\"o}rg and Mainz, Stefan},
  title     = {Direkte Ermittlung der erforderlichen Einspanntiefe von I‑f{\"o}rmigen Stahlquerschnitten in Betonkonstruktionen},
  volume    = {81},
  number    = {11},
  publisher = {Wiley},
  address   = {Weinheim},
  issn      = {1437-1049},
  doi       = {10.1002/stab.201201620},
  pages     = {850 -- 860},
  year      = {2012},
  abstract  = {F{\"u}r die Ermittlung der erforderlichen Einspanntiefe von eingespannten Stahlquerschnitten in Betonkonstruktionen existieren verschiedene Bemessungsmodelle. Diese basieren vorwiegend auf Grundlage nationaler Normen wie z. B. DIN 18800 [1] und DIN 1045 [2], die durch die europ{\"a}ische Normung ersetzt wurden. Aus diesem Grund wird in diesem Aufsatz ein Berechnungsmodell f{\"u}r die erforderliche Einspanntiefe von eingespannten Stahlquerschnitten in Betonkonstruktionen auf Grundlage des Eurocodes vorgestellt. Das Grundger{\"u}st f{\"u}r dieses Berechnungsmodell bildet das Verfahren nach Kindmann und Laumann, welches in [3] behandelt wurde. Gleichzeitig werden neue Formeln zur direkten Ermittlung der Mindesteinspanntiefe vorgestellt. Behandelt werden gewalzte I-Profile f{\"u}r einachsige Biegung um die starke Achse (y-y) mit Drucknormalkraft.},
  language  = {de}
}
@article{KurulganDemirciDemirciLinderetal.2012,
  author    = {Kurulgan Demirci, Eylem and Demirci, Taylan and Linder, Peter and Trzewik, J{\"u}rgen and Gierkowski, Jessica Ricarda and Gossmann, Matthias and Kayser, Peter and Porst, Dariusz and Digel, Ilya and Artmann, Gerhard and Temiz Artmann, Ayseg{\"u}l},
  title     = {rhAPC reduces the endothelial cell permeability via a decrease of contractile tensions induced by endothelial cells},
  series = {Journal of Bioscience and Bioengineering},
  volume    = {113},
  journal   = {Journal of Bioscience and Bioengineering},
  number    = {2},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1347-4421},
  doi       = {10.1016/j.jbiosc.2012.03.019},
  pages     = {212 -- 219},
  year      = {2012},
  abstract  = {All cells generate contractile tension. This strain is crucial for mechanically controlling the cell shape, function and survival. In this study, the CellDrum technology quantifying cell's (the cellular) mechanical tension on a pico-scale was used to investigate the effect of lipopolysaccharide (LPS) on human aortic endothelial cell (HAoEC) tension. The LPS effect during gram-negative sepsis on endothelial cells is cell contraction causing endothelium permeability increase. The aim was to finding out whether recombinant activated protein C (rhAPC) would reverse the endothelial cell response in an in-vitro sepsis model. In this study, the established in-vitro sepsis model was confirmed by interleukin 6 (IL-6) levels at the proteomic and genomic levels by ELISA, real time-PCR and reactive oxygen species (ROS) activation by florescence staining. The thrombin cellular contraction effect on endothelial cells was used as a positive control when the CellDrum technology was applied. Additionally, the Ras homolog gene family, member A (RhoA) mRNA expression level was checked by real time-PCR to support contractile tension results. According to contractile tension results, the mechanical predominance of actin stress fibers was a reason of the increased endothelial contractile tension leading to enhanced endothelium contractility and thus permeability enhancement. The originality of this data supports firstly the basic measurement principles of the CellDrum technology and secondly that rhAPC has a beneficial effect on sepsis influenced cellular tension. The technology presented here is promising for future high-throughput cellular tension analysis that will help identify pathological contractile tension responses of cells and prove further cell in-vitro models.},
  language  = {en}
}
@article{KrollLudwigs2012,
  author    = {Kroll-Ludwigs, Kathrin},
  title     = {Ein optionales Vertragsrecht f{\"u}r Europa: Motor oder Hemmnis f{\"u}r den Binnenmarkt?},
  series = {GPR : Zeitschrift f{\"u}r Gemeinschaftsprivatrecht},
  volume    = {9},
  journal   = {GPR : Zeitschrift f{\"u}r Gemeinschaftsprivatrecht},
  number    = {4},
  publisher = {Verlag Dr. Otto Schmidt},
  address   = {K{\"o}ln},
  issn      = {2193-9519},
  doi       = {10.1515/gpr.2012.9.4.181},
  pages     = {181 -- 188},
  year      = {2012},
  language  = {de}
}
@article{KotliarLanzlHanssenetal.2012,
  author    = {Kotliar, Konstantin and Lanzl, Ines M. and Hanssen, Henner and Eberhardt, Karla and Vilser, Walthard and Halle, Martin and Heemann, Uwe and Schmidt-Trucks{\"a}ss, Arno and Baumann, Marcus},
  title     = {Does increased blood pressure rather than aging influence retinal pulse wave velocity?},
  series = {Investigative Ophthalmology \& Visual Science, IOVS},
  volume    = {53},
  journal   = {Investigative Ophthalmology \& Visual Science, IOVS},
  number    = {4},
  publisher = {ARVO},
  address   = {Rockville, Md.},
  issn      = {0146-0404},
  doi       = {10.1167/iovs.11-8815},
  pages     = {2119 -- 2126},
  year      = {2012},
  abstract  = {Purpose: It was demonstrated previously that retinal pulse wave velocity (rPWV) as a measure of retinal arterial stiffness is increased in aged anamnestically healthy volunteers compared with young healthy subjects. Using novel methodology of rPWV assessment this finding was confirmed and investigated whether it might relate to the increased blood pressure usually accompanying the aging process, rather than to the aging itself. Methods: A total of 12 young 25.5-year-old (24.0-28.8) [median(1st quartile-3rd quartile)] and 12 senior 68.5-year-old (63.8-71.8) anamnestically healthy volunteers; and 12 senior 63.0-year-old (60.8-65.0) validated healthy volunteers and 12 young 33.0-year-old (29.5-35.0) hypertensive patients were examined. Time-dependent alterations of vessel diameter were assessed by the Dynamic Vessel Analyzer in a retinal artery of each subject. The data were filtered and processed using mathematical signal analysis and rPWVs were calculated. Results: rPWV amounted to 1200 (990-1470) RU (relative units)/s in the hypertensive group and to 1040 (700-2230) RU/s in anamnestically healthy seniors. These differed significantly from rPWVs in young healthy group (410 [280-500] RU/s) and in validated healthy seniors (400 [320-510] RU/s). rPWV associated with age and mean arterial pressure (MAP) in the pooled cohort excluded validated healthy seniors. In a regression model these associations remain when alternately adjusted for MAP and age. When including validated healthy seniors in the pooled cohort only association with MAP remains. Conclusions: Both aging (with not excluded cardiovascular risk factors) and mild hypertension are associated with elevated rPWV. rPWV increases to a similar extent both in young mildly hypertensive subjects and in aged anamnestically healthy persons. Healthy aging is not associated with increased rPWV.},
  language  = {en}
}
@article{KobusBitzUdenetal.2012,
  author    = {Kobus, Thiele and Bitz, Andreas and Uden, Mark J. van and Lagemaat, Miram W. and Rothgang, Eva and Orzada, Stephan and Heerschap, Arend and Scheenen, Tom W. J.},
  title     = {In vivo 31P MR spectroscopic imaging of the human prostate at 7 T: safety and feasibility},
  series = {Magnetic Resonance in Medicine},
  volume    = {68},
  journal   = {Magnetic Resonance in Medicine},
  number    = {6},
  publisher = {Wiley-Liss},
  address   = {New York},
  issn      = {1522-2594},
  doi       = {10.1002/mrm.24175},
  pages     = {1683 -- 1695},
  year      = {2012},
  abstract  = {31P MR spectroscopic imaging of the human prostate provides information about phosphorylated metabolites that could be used for prostate cancer characterization. The sensitivity of a magnetic field strength of 7 T might enable 3D 31P MR spectroscopic imaging with relevant spatial resolution in a clinically acceptable measurement time. To this end, a 31P endorectal coil was developed and combined with an eight-channel 1H body-array coil to relate metabolic information to anatomical location. An extensive safety validation was performed to evaluate the specific absorption rate, the radiofrequency field distribution, and the temperature distribution of both coils. This validation consisted of detailed Finite Integration Technique simulations, confirmed by MR thermometry and Burn:x-wiley:07403194:media:MRM24175:tex2gif-stack-1 measurements in a phantom and in vivo temperature measurements. The safety studies demonstrated that the presence of the 31P endorectal coil had no influence on the specific absorption rate levels and temperature distribution of the external eight-channel 1H array coil. To stay within a 10 g averaged local specific absorption rate of 10 W/kg, a maximum time-averaged input power of 33 W for the 1H array coil was allowed. For transmitting with the 31P endorectal coil, our safety limit of less than 1°C temperature increase in vivo during a 15-min MR spectroscopic imaging experiment was reached at a time-averaged input power of 1.9 W. With this power setting, a second in vivo measurement was performed on a healthy volunteer. Using adiabatic excitation, 3D 31P MR spectroscopic imaging produced spectra from the entire prostate in 18 min with a spatial resolution of 4 cm3. The spectral resolution enabled the separate detection of phosphocholine, phosphoethanolamine, inorganic phosphate, and other metabolites that could play an important role in the characterization of prostate cancer.},
  language  = {en}
}
@article{Knueppel2012,
  author    = {Kn{\"u}ppel, Mark},
  title     = {Außerbilanzielle Korrekturen},
  series = {Handbuch der Bilanzierung online},
  journal   = {Handbuch der Bilanzierung online},
  editor    = {Federmann, Rudolf and Kußmaul, Heinz and M{\"u}ller, Stefan},
  publisher = {Haufe},
  address   = {Freiburg},
  issn      = {0172-0392},
  pages     = {Artikel HI 1380074},
  year      = {2012},
  language  = {de}
}
@article{KlingeWilkeMuehl2012,
  author    = {Klinge, Uwe and Wilke, Ralf and M{\"u}hl, Thomas},
  title     = {Auswahl der Herniennetze nach der "effektiven Porosit{\"a}t" - warum das Gewicht weniger wichtig ist},
  series = {Chirurgische Allgemeine : CHAZ ; Zeitung f{\"u}r Klinik und Praxis},
  volume    = {13},
  journal   = {Chirurgische Allgemeine : CHAZ ; Zeitung f{\"u}r Klinik und Praxis},
  number    = {12},
  publisher = {Kaden},
  address   = {Mannheim},
  isbn      = {1615-5378},
  pages     = {297 -- 301},
  year      = {2012},
  language  = {de}
}
@article{KirsteinMuellerWaleckiMingersetal.2012,
  author    = {Kirstein, Simon and M{\"u}ller, Karsten and Walecki-Mingers, Mark and Deserno, Thomas M.},
  title     = {Robust adaptive flow line detection in sewer pipes},
  series = {Automation in construction},
  journal   = {Automation in construction},
  number    = {21},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1872-7891 (E-Journal) ; 0926-5805 (Print)},
  doi       = {10.1016/j.autcon.2011.05.009},
  pages     = {24 -- 31},
  year      = {2012},
  abstract  = {As part of a novel approach to automatic sewer inspection, this paper presents a robust algorithm for automatic flow line detection. A large image repository is obtained from about 50,000 m sewers to represent the high variability of real world sewer systems. Automatic image processing combines Canny edge detection, Hough transform for straight lines and cost minimization using Dijkstra's shortest path algorithm. Assuming that flow lines are mostly smoothly connected horizontal structures, piecewise flow line delineation is reduced to a process of selecting adjacent line candidates. Costs are derived from the gap between adjacent candidates and their reliability. A single parameter α enables simple control of the algorithm. The detected flow line may precisely follow the segmented edges (α = 0.0) or minimize gaps at joints (α = 1.0). Both, manual and ground truth-based analysis indicate that α = 0.8 is optimal and independent of the sewer's material. The algorithm forms an essential step to further automation of sewer inspection.},
  language  = {en}
}
@article{KirchnerReisertPuetzetal.2012,
  author    = {Kirchner, Patrick and Reisert, Steffen and P{\"u}tz, Patrick and Keusgen, Michael and Sch{\"o}ning, Michael Josef},
  title     = {Characterisation of polymeric materials as passivation layer for calorimetric H2O2 gas sensors},
  series = {Physica Status Solidi (a)},
  volume    = {209},
  journal   = {Physica Status Solidi (a)},
  number    = {5},
  publisher = {Wiley-VCH},
  address   = {Weinheim},
  issn      = {1862-6319},
  doi       = {10.1002/pssa.201100773},
  pages     = {859 -- 863},
  year      = {2012},
  abstract  = {Calorimetric gas sensors for monitoring the H₂O₂ concentration at elevated temperatures in industrial sterilisation processes have been presented in previous works. These sensors are built up in form of a differential set-up of a catalytically active and passive temperature-sensitive structure. Although, various types of catalytically active dispersions have been studied, the passivation layer has to be established and therefore, chemically as well as physically characterised. In the present work, fluorinated ethylene propylene (FEP), perfluoralkoxy (PFA) and epoxy-based SU-8 photoresist as temperature-stable polymeric materials have been investigated for sensor passivation in terms of their chemical inertness against H₂O₂, their hygroscopic properties as well as their morphology. The polymeric materials were deposited via spin-coating on the temperature-sensitive structure, wherein spin-coated FEP and PFA show slight agglomerates. However, they possess a low absorption of humidity due to their hydrophobic surface, whereas the SU-8 layer has a closed surface but shows a slightly higher absorption of water. All of them were inert against gaseous H₂O₂ during the characterisation in H₂O₂ atmosphere that demonstrates their suitability as passivation layer for calorimetric H₂O₂ gas sensors.},
  language  = {en}
}
@article{KirchnerOberlaenderFriedrichetal.2012,
  author    = {Kirchner, Patrick and Oberl{\"a}nder, Jan and Friedrich, Peter and Berger, J{\"o}rg and Rysstad, Gunnar and Sch{\"o}ning, Michael Josef and Keusgen, Michael},
  title     = {Realisation of a calorimetric gas sensor on polyimide foil for applications in aseptic food industry},
  series = {Sensors and Actuators B: Chemical},
  volume    = {170},
  journal   = {Sensors and Actuators B: Chemical},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0925-4005},
  doi       = {10.1016/j.snb.2011.01.032},
  pages     = {60 -- 66},
  year      = {2012},
  abstract  = {A calorimetric gas sensor is presented for the monitoring of vapour-phase H2O2 at elevated temperature during sterilisation processes in aseptic food industry. The sensor was built up on a flexible polyimide foil (thickness: 25 μm) that has been chosen due to its thermal stability and low thermal conductivity. The sensor set-up consists of two temperature-sensitive platinum thin-film resistances passivated by a layer of SU-8 photo resist and catalytically activated by manganese(IV) oxide. Instead of an active heating structure, the calorimetric sensor utilises the elevated temperature of the evaporated H2O2 aerosol. In an experimental test rig, the sensor has shown a sensitivity of 4.78 °C/(\%, v/v) in a H2O2 concentration range of 0\%, v/v to 8\%, v/v. Furthermore, the sensor possesses the same, unchanged sensor signal even at varied medium temperatures between 210 °C and 270 °C of the gas stream. At flow rates of the gas stream from 8 m3/h to 12 m3/h, the sensor has shown only a slightly reduced sensitivity at a low flow rate of 8 m3/h. The sensor characterisation demonstrates the suitability of the calorimetric gas sensor for monitoring the efficiency of industrial sterilisation processes.},
  language  = {en}
}
@article{KirchhofKraft2012,
  author    = {Kirchhof, Michael and Kraft, Bodo},
  title     = {Hybrides Vorgehensmodell : Agile und klassische Methoden im Projekt passend kombinieren},
  series = {ProjektMagazin},
  journal   = {ProjektMagazin},
  number    = {11},
  publisher = {Berleb Media},
  address   = {Taufkirchen},
  pages     = {11 S.},
  year      = {2012},
  abstract  = {Agil ist im Trend und immer mehr Unternehmen, die ihre Projekte bisher nach klassischen Prinzipien durchf{\"u}hrten, denken {\"u}ber den Einsatz agiler Methoden nach. Doch selbst wenn die Organisation bereits beide Philosophien unterst{\"u}tzt, gilt f{\"u}r ein Projekt meist die klare Vorgabe: agil oder klassisch. Es gibt aber noch einen anderen Ansatz, mit diesen "unterschiedlichen Welten" umzugehen: Und zwar die beiden Philosophien innerhalb eines Projekts zu kombinieren. Wie dies in der Praxis aussehen und gelingen kann, zeigen Dr. Michael Kirchhof und Prof. Dr. Bodo Kraft in diesem Beitrag.},
  language  = {de}
}
@article{KernSchelthoffMathieu2012,
  author    = {Kern, Alexander and Schelthoff, Christof and Mathieu, Moritz},
  title     = {Detaillierte Berechnung der Einfangwirksamkeiten von Fangeinrichtungen},
  series = {Elektro-Praktiker},
  volume    = {66},
  journal   = {Elektro-Praktiker},
  number    = {4},
  publisher = {Huss Medien},
  address   = {Berlin},
  issn      = {0013-5569},
  pages     = {6 Seiten},
  year      = {2012},
  abstract  = {Im Beitrag wird zun{\"a}chst das Verfahren eines dynamischen elektro-geometrischen Modells vorgestellt. Dieses arbeitet im Gegensatz zum klassischen Blitzkugel-Verfahren nicht mit konstanten Radien; vielmehr wird der Radius der Blitzkugel variiert. Dabei werden ausschließlich vorhandene und in internationalen Normen anerkannte Ergebnisse, blitzphysikalische Grundlagen und Untersuchungen verwendet, und auf deren Grundlage ein numerisches Verfahren erarbeitet. Mit dem dynamischen elektro-geometrischen Modell werden dann einige Beispiele des Schutzes mit Fangstangen, die gem{\"a}ß dem klassischen Blitzkugel-Verfahren nach DIN EN 62305-3 f{\"u}r die Schutzklassen I - II - III - IV geplant sind, untersucht. Es wird gezeigt, dass die Einfangwirksamkeiten wesentlich h{\"o}her sind als in der Normenreihe DIN EN 62305 selbst angegeben. Grund daf{\"u}r ist die Tatsache, dass das Blitzkugel-Verfahren sehr konservativ aufgebaut ist und dem Planer von Blitzschutzsystemen nur die m{\"o}glichen Stellen f{\"u}r einen Einschlag aufzeigt, ohne eine Bewertung der Einschlagsh{\"a}ufigkeit zu liefern. Andererseits bedeutet dies jedoch, dass man mit dem klassischen Blitzkugel-Verfahren stets auf der „sicheren Seite" liegt.},
  language  = {de}
}
@article{Jochim2012,
  author    = {Jochim, Haldor E.},
  title     = {Die Ostheidebahn - eine Alternative zur Y-Trasse},
  series = {ETR - Eisenbahntechnische Rundschau},
  volume    = {61},
  journal   = {ETR - Eisenbahntechnische Rundschau},
  number    = {11},
  publisher = {DVV Media Group},
  address   = {Hamburg},
  issn      = {0013-2845},
  pages     = {34 -- 37},
  year      = {2012},
  language  = {de}
}
@article{ImmelGruetzkeSpaeteetal.2012,
  author    = {Immel, Timo and Gr{\"u}tzke, Martin and Sp{\"a}te, Anne-Katrin and Groth, Ulrich and {\"O}hlschl{\"a}ger, Peter and Huhn, Thomas},
  title     = {Synthesis and X-ray structure analysis of a heptacoordinate titanium(IV)-bis-chelate with enhanced in vivo antitumor efficacy},
  series = {Chemical Communications},
  volume    = {48},
  journal   = {Chemical Communications},
  number    = {46},
  publisher = {Royal Society of Chemistry},
  address   = {Cambridge},
  issn      = {1364-548X},
  doi       = {10.1039/C2CC31624B},
  pages     = {5790 -- 5792},
  year      = {2012},
  abstract  = {Chelate stabilization of a titanium(IV)-salan alkoxide by ligand exchange with 2,6-pyridinedicarboxylic acid (dipic) resulted in heptacoordinate complex 3 which is not redox-active, stable on silica gel and has increased aqueous stability. 3 is highly toxic in HeLa S3 and Hep G2 and has enhanced antitumor efficacy in a mouse cervical-cancer model.},
  language  = {en}
}
@article{IkenKirsanovLeginetal.2012,
  author    = {Iken, Heiko and Kirsanov, D. and Legin, A. and Sch{\"o}ning, Michael Josef},
  title     = {Novel Thin-Film Polymeric Materials for the Detection of Heavy Metals},
  series = {Procedia Engineering},
  journal   = {Procedia Engineering},
  number    = {47},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1877-7058},
  doi       = {10.1016/j.proeng.2012.09.148},
  pages     = {322 -- 325},
  year      = {2012},
  abstract  = {A variety of transition metals, e.g., copper, zinc, cadmium, lead, etc. are widely used in industry as components for wires, coatings, alloys, batteries, paints and so on. The inevitable presence of transition metals in industrial processes implies the ambition of developing a proper analytical technique for their adequate monitoring. Most of these elements, especially lead and cadmium, are acutely toxic for biological organisms. Quantitative determination of these metals at low activity levels in different environmental and industrial samples is therefore a vital task. A promising approach to achieve an at-side or on-line monitoring on a miniaturized and cost efficient way is the combination of a common potentiometric sensor array with heavy metal-sensitive thin-film materials, like chalcogenide glasses and polymeric materials, respectively.},
  language  = {en}
}
@article{Huening2012,
  author    = {H{\"u}ning, Felix},
  title     = {Using Trench PowerMOSFETs in Linear Mode},
  series = {Power Electronics Europe (2012)},
  journal   = {Power Electronics Europe (2012)},
  publisher = {DFA Media},
  address   = {Tonbridge},
  issn      = {1748-3530},
  pages     = {27 -- 29},
  year      = {2012},
  abstract  = {If we think about applications for modern Power MOSFETs using trench technology, running them in linear mode may not be top of the priority list. Yet there are multiple uses for Trench Power MOSFETs in linear mode. In fact, even turning the device on and off in switching applications is a form of linear operation. Also, these components can be run in linear mode to protect the device against voltage surges. This article will illustrate the factors that need to be considered for linear operation and show how Trench Power MOSFETs are suited to it.},
  language  = {en}
}
@article{HoetterFateriGebhardt2012,
  author    = {H{\"o}tter, Jan-Steffen and Fateri, Miranda and Gebhardt, Andreas},
  title     = {Prozessoptimierung des SLM-Prozesses mit hoch-reflektiven und thermisch sehr gut leitenden Materialien durch systematische Parameterfindung und begleitende Simulationen am Beispiel von Silber},
  series = {RTejournal - Forum f{\"u}r Rapid Technologie},
  volume    = {9},
  journal   = {RTejournal - Forum f{\"u}r Rapid Technologie},
  number    = {1},
  publisher = {Fachhoschule Aachen},
  address   = {Aachen},
  issn      = {1614-0923},
  url       = {http://nbn-resolving.de/urn:nbn:de:0009-2-33639},
  pages     = {1 -- 14},
  year      = {2012},
  abstract  = {Additive Manufacturing durch Aufschmelzen von Metallpulvern hat sich auf breiter Front als Herstellverfahren, auch f{\"u}r Endprodukte, etabliert. Besonders f{\"u}r die Variante des Selective Laser Melting (SLM) sind Anwendungen in der Zahntechnik bereits weit verbreitet und der Einsatz in sensitiven Branchen wie der Luftfahrt ist in greifbare N{\"a}he ger{\"u}ckt. Deshalb werden auch vermehrt Anstrengungen unternommen, um bisher nicht verarbeitete Materialien zu qualifizieren. Dies sind vorzugsweise Nicht-Eisen- und Edelmetalle, die sowohl eine sehr hohe Reflektivit{\"a}t als auch eine sehr gute W{\"a}rmeleitf{\"a}higkeit aufweisen - beides Eigenschaften, die die Beherrschung des Laser-Schmelzprozesses erschweren und nur kleine Prozessfenster zulassen. Die Arbeitsgruppe SLM des Lehr- und Forschungsgebietes Hochleistungsverfahren der Fertigungstechnik hat sich unter der Randbedingung einer kleinen und mit geringer Laserleistung ausgestatteten SLM Maschine der Aufgabe gewidmet und am Beispiel von Silber die Parameterfelder f{\"u}r Einzelspuren und wenig komplexe Geometrien systematisch untersucht. Die Arbeiten wurden von FEM Simulationen begleitet und durch metallographische Untersuchungen verifiziert. Die Ergebnisse bilden die Grundlage zur schnellen Parameterfindung bei komplexen Geometrien und bei Ver{\"a}nderungen der Zusammensetzung, wie sie bei zuk{\"u}nftigen Legierungen zu erwarten sind. Die Ergebnisse werden exemplarisch auf unterschiedliche Geometrien angewandt und entsprechende Bauteile gezeigt.},
  language  = {de}
}
@article{HoetterFateriGebhardt2012,
  author    = {H{\"o}tter, Jan-Steffen and Fateri, Miranda and Gebhardt, Andreas},
  title     = {Selective laser melting of metals: desktop machines open up new chances even for small companies},
  series = {Advanced materials research},
  volume    = {622-623},
  journal   = {Advanced materials research},
  publisher = {Trans Tech Publ.},
  address   = {Baech},
  issn      = {1662-8985 (E-Journal); 1022-6680 (Print)},
  doi       = {10.4028/www.scientific.net/AMR.622-623.461},
  pages     = {461 -- 465},
  year      = {2012},
  abstract  = {Additive manufacturing (AM) of metal parts by using Selective Laser Melting (SLM) has become a powerful tool mostly in the area of automotive, aerospace engineering and others. Especially in the field of dentistry, jewelry and related branches that require individualized or even one-of-a-kind products, the direct digital manufacturing process opens up new ways of design and manufacturing. In these fields, mostly small and medium sized businesses (SME) are operating which do not have sufficient human and economic resources to invest in this technology. But to stay competitive, the application of AM can be regarded as a necessity. In this situation a new desktop machine (Realizer SLM 50) was introduced that cost about 1/3 of a shop floor SLM machine and promises small quality parts. To find out whether the machine really is an alternative for SMEs the University of Applied Science, Aachen, Germany, designed, build and optimized typical parts from the dentistry and the jewelry branches using CoCr and silver material, the latter being new with this application. The paper describes the SLM procedure and how to find and optimize the most important parameters. The test is accompanied by digital simulation in order to verify the build parameters and to plan future builds. The procedure is shown as well as the resulting parts made from CoCr and silver material.},
  language  = {en}
}
@article{HuckPoghossianWagneretal.2012,
  author    = {Huck, Christina and Poghossian, Arshak and Wagner, Patrick and Sch{\"o}ning, Michael Josef},
  title     = {Combined amperometric/field-effect sensor for the detection of dissolved hydrogen},
  series = {Sensors and actuators B: Chemical},
  volume    = {187},
  journal   = {Sensors and actuators B: Chemical},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0925-4005},
  doi       = {10.1016/j.snb.2012.10.050},
  pages     = {168 -- 173},
  year      = {2012},
  abstract  = {Real-time and reliable monitoring of the biogas process is crucial for a stable and efficient operation of biogas production in order to avoid digester breakdowns. The concentration of dissolved hydrogen (H₂) represents one of the key parameters for biogas process control. In this work, a one-chip integrated combined amperometric/field-effect sensor for monitoring the dissolved H₂ concentration has been developed for biogas applications. The combination of two different transducer principles might allow a more accurate and reliable measurement of dissolved H₂ as an early warning indicator of digester failures. The feasibility of the approach has been demonstrated by simultaneous amperometric/field-effect measurements of dissolved H₂ concentrations in electrolyte solutions. Both, the amperometric and the field-effect transducer show a linear response behaviour in the H₂ concentration range from 0.1 to 3\% (v/v) with a slope of 198.4 ± 13.7 nA/\% (v/v) and 14.9 ± 0.5 mV/\% (v/v), respectively.},
  language  = {en}
}
@article{HerzwurmKramsPietschetal.2012,
  author    = {Herzwurm, Georg and Krams, Benedikt and Pietsch, Wolfram and Schockert, Sixten},
  title     = {Report from the 3rd international workshop on requirements prioritization for customer oriented software development (RePriCo'12)},
  series = {ACM SIGSOFT Software Engineering Notes},
  volume    = {37},
  journal   = {ACM SIGSOFT Software Engineering Notes},
  number    = {4},
  publisher = {Association for Computing Machinery},
  address   = {New York},
  issn      = {0163-5948},
  doi       = {10.1145/2237796.2237817},
  pages     = {32 -- 34},
  year      = {2012},
  abstract  = {Prioritization is an essential task within requirements engineering to cope with complexity and to establish focus properly. The 3rd Workshop on Requirements Prioritization for customer oriented Software Development (RePriCo'12) focused on requirements prioritization and adjacent themes in the context of customer oriented development of bespoke and standard software. Five submissions have been accepted for the proceedings and for presentation. The report summarizes and points out key findings.},
  language  = {en}
}
@article{HenkenOosterhuisOehlschlaegeretal.2012,
  author    = {Henken, F. E. and Oosterhuis, K. and {\"O}hlschl{\"a}ger, Peter and Bosch, L. and Hooijberg, E. and Haanen, J. B. A. G. and Steenbergen, R. D. M.},
  title     = {Preclinical safety evaluation of DNA vaccines encoding modified HPV16 E6 and E7},
  series = {Vaccine},
  volume    = {30},
  journal   = {Vaccine},
  number    = {28},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0264-410X},
  doi       = {10.1016/j.vaccine.2012.04.013},
  pages     = {4259 -- 4266},
  year      = {2012},
  abstract  = {Persistent infection with high-risk human papillomaviruses (hrHPV) can result in the formation of anogenital cancers. As hrHPV proteins E6 and E7 are required for cancer initiation and maintenance, they are ideal targets for immunotherapeutic interventions. Previously, we have described the development of DNA vaccines for the induction of HPV16 E6 and E7 specific T cell immunity. These vaccines consist of 'gene-shuffled' (SH) versions of HPV16 E6 and E7 that were fused to Tetanus Toxin Fragment C domain 1 (TTFC) and were named TTFC-E6SH and TTFC-E7SH. Gene-shuffling was performed to avoid the risk of inducing malignant transformation at the vaccination site. Here, we describe the preclinical safety evaluation of these candidate vaccines by analysis of their transforming capacity in vitro using established murine fibroblasts (NIH 3T3 cells) and primary human foreskin keratinocytes (HFKs). We demonstrate that neither ectopic expression of TTFC-E6SH and TTFC-E7SH alone or in combination enabled NIH 3T3 cells to form colonies in soft agar. In contrast, expression of HPV16 E6WT and E7WT alone or in combination resulted in effective transformation. Similarly, retroviral transduction of HFKs from three independent donors with both TTFC-E6SH and TTFC-E7SH alone or in combination did not show any signs of immortalization. In contrast, the combined expression of E6WT and E7WT induced immortalization in HFKs from all donors. Based on these results we consider it justified to proceed to clinical evaluation of DNA vaccines encoding TTFC-E6SH and TTFC-E7SH in patients with HPV16 associated (pre)malignancies.},
  language  = {en}
}
@article{HasanKeilStaatetal.2012,
  author    = {Hasan, Istabrak and Keil, Ludger and Staat, Manfred and Wahl, Gerhard and Bourauel, Christoph},
  title     = {Determination of the frictional coefficient of the implant-antler interface : experimental approach},
  series = {Biomedical Engineering / Biomedizinische Technik},
  volume    = {57},
  journal   = {Biomedical Engineering / Biomedizinische Technik},
  number    = {5},
  publisher = {De Gruyter},
  address   = {Berlin},
  issn      = {1862-278X},
  pages     = {359 -- 363},
  year      = {2012},
  abstract  = {The similar bone structure of reindeer antler to human bone permits studying the osseointegration of dental implants in the jawbone. As the friction is one of the major factors that have a significant influence on the initial stability of immediately loaded dental implants, it is essential to define the frictional coefficient of the implant-antler interface. In this study, the kinetic frictional forces at the implant-antler interface were measured experimentally using an optomechanical setup and a stepping motor controller under different axial loads and sliding velocities. The corresponding mean values of the static and kinetic frictional coefficients were within the range of 0.5-0.7 and 0.3-0.5, respectively. An increase in the frictional forces with increasing applied axial loads was registered. The measurements showed an evidence of a decrease in the magnitude of the frictional coefficient with increasing sliding velocity. The results of this study provide a considerable assessment to clarify the suitable frictional coefficient to be used in the finite element contact analysis of antler specimens.},
  language  = {en}
}
@article{GutheilBergGrotendorst2012,
  author    = {Gutheil, Inge and Berg, Tommy and Grotendorst, Johannes},
  title     = {Performance Analysis of Parallel Eigensolvers of two Libraries on BlueGene/P},
  series = {Journal of Mathematics and Systems Science},
  volume    = {2},
  journal   = {Journal of Mathematics and Systems Science},
  number    = {4},
  publisher = {David Publishing},
  address   = {Libertyville},
  issn      = {2159-5291},
  doi       = {10.17265/2159-5291/2012.04.003},
  pages     = {231 -- 236},
  year      = {2012},
  abstract  = {Many applications in computational science and engineering require the computation of eigenvalues and vectors of dense symmetric or Hermitian matrices. For example, in DFT (density functional theory) calculations on modern supercomputers 10\% to 30\% of the eigenvalues and eigenvectors of huge dense matrices have to be calculated. Therefore, performance and parallel scaling of the used eigensolvers is of upmost interest. In this article different routines of the linear algebra packages ScaLAPACK and Elemental for parallel solution of the symmetric eigenvalue problem are compared concerning their performance on the BlueGene/P supercomputer. Parameters for performance optimization are adjusted for the different data distribution methods used in the two libraries. It is found that for all test cases the new library Elemental which uses a two-dimensional element by element distribution of the matrices to the processors shows better performance than the old ScaLAPACK library which uses a block-cyclic distribution.},
  language  = {en}
}
@article{Grotendorst2012,
  author    = {Grotendorst, Johannes},
  title     = {Supercomputer programmieren - ein besonderes Studienangebot in J{\"u}lich},
  series = {Junge Wissenschaft. 27 (2012), H. 94},
  journal   = {Junge Wissenschaft. 27 (2012), H. 94},
  publisher = {-},
  isbn      = {0179-8529},
  pages     = {12 -- 14},
  year      = {2012},
  language  = {de}
}
@article{Grotendorst2012,
  author    = {Grotendorst, Johannes},
  title     = {IAS Winter School: Hierarchical Methods for Dynamics in Complex Molecular Systems},
  series = {Innovatives Supercomputing in Deutschland : inSiDE. 10 (2012), H. 1},
  journal   = {Innovatives Supercomputing in Deutschland : inSiDE. 10 (2012), H. 1},
  publisher = {-},
  pages     = {104},
  year      = {2012},
  language  = {en}
}
@article{GrinsvenBonStrauvenetal.2012,
  author    = {Grinsven, Bart van and Bon, Natalie vanden and Strauven, Hannelore and Grieten, Lars and Murib, Mohammed and Jim{\´e}nez Monroy, Kathia L. and Janssens, Stoffel D. and Haenen, Ken and Sch{\"o}ning, Michael Josef and Vermeeren, Veronique and Ameloot, Marcel and Michiels, Luc and Thoelen, Ronald and Ceuninck, Ward de and Wagner, Patrick},
  title     = {Heat-Transfer Resistance at Solid-Liquid Interfaces: A Tool for The Detection of Single Nucleotide Polymorphisms in DNA.},
  series = {ACS Nano},
  volume    = {6},
  journal   = {ACS Nano},
  number    = {3},
  publisher = {ACS Publications},
  address   = {Washington, DC},
  issn      = {1936-086X},
  doi       = {10.1021/nn300147e},
  pages     = {2712 -- 2721},
  year      = {2012},
  abstract  = {In this article, we report on the heat-transfer resistance at interfaces as a novel, denaturation-based method to detect single-nucleotide polymorphisms in DNA. We observed that a molecular brush of double-stranded DNA grafted onto synthetic diamond surfaces does not notably affect the heat-transfer resistance at the solid-to-liquid interface. In contrast to this, molecular brushes of single-stranded DNA cause, surprisingly, a substantially higher heat-transfer resistance and behave like a thermally insulating layer. This effect can be utilized to identify ds-DNA melting temperatures via the switching from low- to high heat-transfer resistance. The melting temperatures identified with this method for different DNA duplexes (29 base pairs without and with built-in mutations) correlate nicely with data calculated by modeling. The method is fast, label-free (without the need for fluorescent or radioactive markers), allows for repetitive measurements, and can also be extended toward array formats. Reference measurements by confocal fluorescence microscopy and impedance spectroscopy confirm that the switching of heat-transfer resistance upon denaturation is indeed related to the thermal on-chip denaturation of DNA.},
  language  = {en}
}
@article{GorissenStaatLaack2012,
  author    = {Gorissen, P. and Staat, Manfred and Laack, Walter van},
  title     = {Experimentelle Kraftmessungen als Beitrag zur Wirksamkeitsbeurteilung von Schienbeinschonern im Fußballsport},
  series = {OUP Zeitschrift f{\"u}r die orthop{\"a}dische und unfallchirurgische Praxis},
  volume    = {1},
  journal   = {OUP Zeitschrift f{\"u}r die orthop{\"a}dische und unfallchirurgische Praxis},
  number    = {1},
  publisher = {Deutscher {\"A}rzte-Verlag},
  address   = {K{\"o}ln},
  issn      = {2193-5785},
  doi       = {10.3238/oup.2012.0010-0015},
  pages     = {10 -- 15},
  year      = {2012},
  abstract  = {Diese Studie besch{\"a}ftigte sich mit der D{\"a}mpfungswirkung von Schienbeinschonern, wie sie beim Fußball zum Einsatz kommen. Sie wurde mit Hilfe eines Pendelhammers durchgef{\"u}hrt, der verschiedene Aufschlagkr{\"a}fte auf die Schoner erm{\"o}glichte. Dabei wurde deutlich, dass Schienbeinschoner die beste Wirkung bei Maximalkr{\"a}ften unterhalb von 5kN erreichen k{\"o}nnen, dass bei gr{\"o}ßerer Belastung allerdings Verbesserungsbedarf besteht. Hierf{\"u}r konnte, u.a. durch den Einsatz neuer Materialien, ein guter Ansatzpunkt im „ad{\"a}quaten Zusammenspiel von Schale und Polsterung" der Schoner gefunden werden. Die Untersuchung hat weiterhin gezeigt, dass zumindest teilweise eine deutliche Verbesserung der D{\"a}mpfungswirkung der Schienbeinschoner in den letzten Jahren erreicht werden konnte.},
  subject      = {Fußball},
  language  = {de}
}
@article{Frings2012,
  author    = {Frings, Michael},
  title     = {Immobilienfinanzierung und Verbraucherkredit : Das neue Verbraucherkreditrecht nach der Verbraucherkreditrichtlinie},
  series = {NWB : Steuer- und Wirtschaftsrecht},
  volume    = {2012},
  journal   = {NWB : Steuer- und Wirtschaftsrecht},
  number    = {15},
  publisher = {NWB-Verlag},
  address   = {Herne},
  issn      = {0028-3460},
  pages     = {1237 -- 1247},
  year      = {2012},
  abstract  = {Mit Gesetz vom 29.7.2009 (BGBl 2009 I S. 2355) hat der deutsche Gesetzgeber die EU-Verbraucherkreditrichtlinie 2008/48/EG vom 23.4.2008 NWB PAAAD-28762 in nationales Recht umgesetzt. In diesem Gesetz ist auch der Immobiliardarlehensvertrag neu geregelt worden. Auf diese besondere Kreditform sind grds. die Vorschriften zum Verbraucherkredit anzuwenden, so dass der Darlehensgeber auch im Fall einer Immobilienfinanzierung zu vorvertraglicher Information des Verbrauchers verpflichtet ist. Beim finanzierten Immobilienerwerb werden Ver{\"a}ußerer und kreditgebende Bank h{\"a}ufig in Abstimmung und Zusammenarbeit t{\"a}tig, so dass f{\"u}r die Bank besondere Aufkl{\"a}rungspflichten gegen{\"u}ber dem Verbraucher entstehen. Im Fall der Verletzung dieser Pflichten drohen ihr Schadensersatzanspr{\"u}che oder ein Widerrufsrecht des Verbrauchers.},
  language  = {de}
}
@article{Frings2012,
  author    = {Frings, Michael},
  title     = {Verbesserter Schutz vor Kostenfallen im elektronischen Gesch{\"a}ftsverkehr („Buttonl{\"o}sung") : Erster Schritt zur Umsetzung der neuen EU-Verbraucherrechterichtlinie},
  series = {NWB : NWB-Steuer- und Wirtschaftsrecht},
  volume    = {2012},
  journal   = {NWB : NWB-Steuer- und Wirtschaftsrecht},
  number    = {23},
  publisher = {NWB-Verlag},
  address   = {Herne},
  issn      = {0028-3460},
  pages     = {1912 -- 1918},
  year      = {2012},
  abstract  = {Der Deutsche Bundestag und Bundesrat haben am 2.3.2012 bzw. 30.3.2012 das Gesetz gegen Kostenfallen im Internet verabschiedet, das am 1.8.2012 in Kraft treten wird. Hiermit hat der deutsche Gesetzgeber einen ersten Schritt getan, um die neue EU-Verbraucherrechterichtlinie vom 25.10.2011 (2011/83/EU, ABl L 304/64) in nationales Recht umzusetzen. Mit dieser Umsetzung ist das dr{\"a}ngendste Problem der Kosten- und Abo-Fallen im elektronischen Gesch{\"a}ftsverkehr aus dem Gesamtpaket der Verbraucherrechterichtlinie herausgel{\"o}st und in dem neugefassten \S 312g BGB behandelt worden. Eile bei der Umsetzung war hier geboten, weil unseri{\"o}se Unternehmen im elektronischen Rechtsverkehr zunehmend und in großem Umfang gegen{\"u}ber ihren Kunden durch irref{\"u}hrende Gestaltungen ihrer Internetseiten verschleiern, dass die angebotenen Leistungen entgeltpflichtig sind.},
  language  = {de}
}