@inproceedings{LangWirtzHeitzeretal.1999,
  author    = {Lang, H. and Wirtz, K. and Heitzer, Michael and Staat, Manfred and Oettel, R.},
  title     = {Zyklische Einspielversuche zur Verifikation von Shakedown-Analysen mittels FEM},
  year      = {1999},
  abstract  = {Im Rahmen von Erm{\"u}dungsanalysen ist nachzuweisen, daß die thermisch bedingten fortschreitenden Deformationen begrenzt bleiben. Hierzu ist die Abgrenzung des Shakedown-Bereiches (Einspielen) vom Ratchetting-Bereich (fortschreitende Deformation) von Interesse. Im Rahmen eines EU-gef{\"o}rderten Forschungsvorhabens wurden Experimente mit einem 4-Stab-Modell durchgef{\"u}hrt. Das Experiment bestand aus einem wassergek{\"u}hlten inneren Rohr und drei isolierten und beheizbaren {\"a}ußeren Probest{\"a}ben. Das System wurde durch alternierende Axialkr{\"a}fte, denen alternierende Temperaturen an den {\"a}ußeren St{\"a}ben {\"u}berlagert wurden, belastet. Die Versuchsparameter wurden teilweise nach vorausgegangenen Einspielanalysen gew{\"a}hlt. W{\"a}hrend der Versuchsdurchf{\"u}hrung wurden Temperaturen und Dehnungen zeitabh{\"a}ngig gemessen. Begleitend und nachfolgend zur Versuchsdurchf{\"u}hrung wurden die Belastungen und die daraus resultierenden Beanspruchungen nachvollzogen. Bei dieser inkrementellen elasto-plastischen Analyse mit dem Programm ANSYS wurden unterschiedliche Werkstoffmodelle angesetzt. Die Ergebnisse dieser Simulationsberechnung dienen dazu, die Shakedown-Analysen mittels FE-Methode zu verifizieren.},
  subject      = {Einspielen <Werkstoff>},
  language  = {de}
}
@inproceedings{KoplinSiemonsOcenValentinetal.2006,
  author    = {Koplin, Tobias J. and Siemons, Maike and Oc{\´e}n-Val{\´e}ntin, C{\´e}sar and Sanders, Daniel and Simon, Ulrich},
  title     = {Workflow for high throughput screening of gas sensing materials},
  url       = {http://nbn-resolving.de/urn:nbn:de:hbz:a96-opus-1407},
  year      = {2006},
  abstract  = {The workflow of a high throughput screening setup for the rapid identification of new and improved sensor materials is presented. The polyol method was applied to prepare nanoparticular metal oxides as base materials, which were functionalised by surface doping. Using multi-electrode substrates and high throughput impedance spectroscopy (HT-IS) a wide range of materials could be screened in a short time. Applying HT-IS in search of new selective gas sensing materials a NO2-tolerant NO sensing material with reduced sensitivities towards other test gases was identified based on iridium doped zinc oxide. Analogous behaviour was observed for iridium doped indium oxide.},
  subject      = {Biosensor},
  language  = {en}
}
@inproceedings{ArinkinDigel2009,
  author    = {Arinkin, Vladimir and Digel, Ilya},
  title     = {Water bridge phenomenon : [abstract]},
  year      = {2009},
  abstract  = {One of interesting but not well known water properties is related to appearance of highly ordered structures in response to strong electrical field. In 1893 Sir William Armstrong placed a cotton thread between two wine glasses filled with chemically pure water. When high DC voltage was applied between the glasses, a connection consisting of water formed, producing a "water bridge"},
  subject      = {Hydrodynamik},
  language  = {en}
}
@inproceedings{KraftZoell2014,
  author    = {Kraft, Bodo and Z{\"o}ll, Axel},
  title     = {Von der Langstrecke zum Sprint - Agile Methoden in traditionellen Unternehmen},
  series = {Projektmanagement und Vorgehensmodelle 2014 : soziale Aspekte und Standardisierung},
  booktitle = {Projektmanagement und Vorgehensmodelle 2014 : soziale Aspekte und Standardisierung},
  editor    = {Engstler, Martin},
  publisher = {Gesellschaft f{\"u}r Informatik},
  address   = {Bonn},
  organization    = {FH Aachen, University of Applied Sciences},
  isbn      = {978-3-88579-630-5},
  pages     = {35 -- 46},
  year      = {2014},
  language  = {de}
}
@inproceedings{KraftWilhelms2005,
  author    = {Kraft, Bodo and Wilhelms, Nils},
  title     = {Visual Knowledge Specification for Conceptual Design},
  year      = {2005},
  abstract  = {Proc. of the 2005 ASCE Intl. Conf. on Computing in Civil Engineering (ICCC 2005) eds. L. Soibelman und F. Pena-Mora, Seite 1-14, ASCE (CD-ROM), Cancun, Mexico, 2005 Current CAD tools are not able to support the fundamental conceptual design phase, and none of them provides consistency analyses of sketches produced by architects. To give architects a greater support at the conceptual design phase, we develop a CAD tool for conceptual design and a knowledge specification tool allowing the definition of conceptually relevant knowledge. The knowledge is specific to one class of buildings and can be reused. Based on a dynamic knowledge model, different types of design rules formalize the knowledge in a graph-based realization. An expressive visual language provides a user-friendly, human readable representation. Finally, consistency analyses enable conceptual designs to be checked against this defined knowledge. In this paper we concentrate on the knowledge specification part of our project.},
  subject      = {CAD},
  language  = {en}
}
@inproceedings{TranStaat2014,
  author    = {Tran, Thanh Ngoc and Staat, Manfred},
  title     = {Uncertain multimode failure and limit analysis of shells},
  series = {11th World Congress on Computational Mechanics (WCCM XI) ; 5th European Conference on Computational Mechanics (ECCM V) ; 6th European Conference on Computational Fluid Dynamics (ECFD VI) ; July 20-25, 2014, Barcelona},
  booktitle = {11th World Congress on Computational Mechanics (WCCM XI) ; 5th European Conference on Computational Mechanics (ECCM V) ; 6th European Conference on Computational Fluid Dynamics (ECFD VI) ; July 20-25, 2014, Barcelona},
  editor    = {Onate, E.},
  organization    = {World Congress on Computational Mechanics <11, 2014, Barcelona>},
  pages     = {1 -- 12},
  year      = {2014},
  language  = {en}
}
@inproceedings{KirchhofKraft2004,
  author    = {Kirchhof, M. and Kraft, Bodo},
  title     = {UML-based modeling of architectural knowledge and design},
  year      = {2004},
  abstract  = {IASSE-2004 - 13th International Conference on Intelligent and Adaptive Systems and Software Engineering eds. W. Dosch, N. Debnath, pp. 245-250, ISCA, Cary, NC, 1-3 July 2004, Nice, France We introduce a UML-based model for conceptual design support in civil engineering. Therefore, we identify required extensions to standard UML. Class diagrams are used for elaborating building typespecific knowledge: Object diagrams, implicitly contained in the architect's sketch, are validated against the defined knowledge. To enable the use of industrial, domain-specific tools, we provide an integrated conceptual design extension. The developed tool support is based on graph rewriting. With our approach architects are enabled to deal with semantic objects during early design phase, assisted by incremental consistency checks.},
  subject      = {UML},
  language  = {en}
}
@inproceedings{HeerRedkowitzKraft2008,
  author    = {Heer, Thomas and Redkowitz, Daniel and Kraft, Bodo},
  title     = {Tool Support for the Integration of Light-Weight Ontologies},
  isbn      = {978-3-642-00670-8},
  year      = {2008},
  abstract  = {Abstract of the authors: In many areas of computer science ontologies become more and more important. The use of ontologies for domain modeling often brings up the issue of ontology integration. The task of merging several ontologies, covering specific subdomains, into one united ontology has to be solved. Many approaches for ontology integration aim at automating the process of ontology alignment. However, a complete automation is not feasible, and user interaction is always required. Nevertheless, most ontology integration tools offer only very limited support for the interactive part of the integration process. In this paper, we present a novel approach for the interactive integration of ontologies. The result of the ontology integration is incrementally updated after each definition of a correspondence between ontology elements. The user is guided through the ontologies to be integrated. By restricting the possible user actions, the integrity of all defined correspondences is ensured by the tool we developed. We evaluated our tool by integrating different regulations concerning building design.},
  subject      = {Ontologie <Wissensverarbeitung>},
  language  = {de}
}
@inproceedings{MansurovZhubanovaDigeletal.2008,
  author    = {Mansurov, Zulkhair and Zhubanova, Azhar A. and Digel, Ilya and Artmann, Gerhard and Temiz Artmann, Ayseg{\"u}l and Savitskaja, Irina S. and Kozhalakova, A. A. and Kistaubaeva, Aida S.},
  title     = {The sorption of LPS toxic shock by nanoparticles on base of carbonized vegetable raw materials},
  year      = {2008},
  abstract  = {Immobilization of lactobacillus on high temperature carbonizated vegetable raw material (rice husk, grape stones) increases their physiological activity and the quantity of the antibacterial metabolits, that consequently lead to increase of the antagonistic activity of lactobacillus. It is implies that the use of the nanosorbents for the attachment of the probiotical microorganisms are highly perspective for decision the important problems, such as the probiotical preparations delivery to the right address and their attachment to intestines mucosa with the following detoxication of gastro-intestinal tract and the normalization of it's microecology. Besides that, thus, the received carbonizated nanoparticles have peculiar properties - ability to sorption of LPS toxical shock and, hence, to the detoxication of LPS.},
  subject      = {Kohlenstofffaser},
  language  = {en}
}
@inproceedings{StaatHeitzer2002,
  author    = {Staat, Manfred and Heitzer, Michael},
  title     = {The restricted influence of kinematic hardening on shakedown loads},
  year      = {2002},
  abstract  = {Structural design analyses are conducted with the aim of verifying the exclusion of ratcheting. To this end it is important to make a clear distinction between the shakedown range and the ratcheting range. In cyclic plasticity more sophisticated hardening models have been suggested in order to model the strain evolution observed in ratcheting experiments. The hardening models used in shakedown analysis are comparatively simple. It is shown that shakedown analysis can make quite stable predictions of admissible load ranges despite the simplicity of the underlying hardening models. A linear and a nonlinear kinematic hardening model of two-surface plasticity are compared in material shakedown analysis. Both give identical or similar shakedown ranges. Structural shakedown analyses show that the loading may have a more pronounced effect than the hardening model.},
  subject      = {Biomedizinische Technik},
  language  = {en}
}
@inproceedings{ArtmannStadlerEmbsetal.2010,
  author    = {Artmann, Gerhard and Stadler, Andreas M. and Embs, Jan P. and Zaccai, Giuseppe and B{\"u}ldt, Georg and Digel, Ilya and Temiz Artmann, Ayseg{\"u}l},
  title     = {The crucial role of water in a phase transition of hemoglobin at body temperature : [abstract]},
  year      = {2010},
  abstract  = {The observation of a temperature transition of hemoglobin occurring at a critical temperature close to body temperature},
  subject      = {H{\"a}moglobin},
  language  = {en}
}
@inproceedings{StadlerEmbsZerlinetal.2007,
  author    = {Stadler, Andreas M. and Embs, Jan P. and Zerlin, Kay and Digel, Ilya and Artmann, Gerhard and Zaccai, Joe and B{\"u}ldt, Georg},
  title     = {Temperature transitions of hemoglobin and cytosolic water diffusion in human red blood cells : [poster]},
  year      = {2007},
  abstract  = {Background Hemoglobin interactions in red blood cells Hemoglobin dynamics in human red blood cells Diffusion of H2O in red blood cells},
  subject      = {Erythrozyt},
  language  = {en}
}
@inproceedings{KreyerStollenwerkSchoening2013,
  author    = {Kreyer, J{\"o}rg and Stollenwerk, Dominik and Sch{\"o}ning, Michael Josef},
  title     = {Tagung des Forschernachwuchses der FH Aachen 20. November 2013 / ed.: J. Kreyer, D. Stollenwerk, M. J. Sch{\"o}ning},
  publisher = {FH Aachen},
  address   = {Aachen},
  pages     = {64 S.},
  year      = {2013},
  language  = {de}
}
@inproceedings{PijanowskaRemiszewskaPederzollietal.2006,
  author    = {Pijanowska, Dorota G. and Remiszewska, Elzbieta and Pederzolli, Cecilia and Lunelli, Lorenzo and Vendano, Michele and Canteri, Roberto and Dudzinski, Konrad and Kruk, Jerzy and Torbicz, Wladyslaw},
  title     = {Surface modification for microreactor fabrication},
  url       = {http://nbn-resolving.de/urn:nbn:de:hbz:a96-opus-1480},
  year      = {2006},
  abstract  = {In this paper, methods of surface modification of different supports, i.e. glass and polymeric beads for enzyme immobilisation are described. The developed method of enzyme immobilisation is based on Schiff's base formation between the amino groups on the enzyme surface and the aldehyde groups on the chemically modified surface of the supports. The surface of silicon modified by APTS and GOPS with immobilised enzyme was characterised by atomic force microscopy (AFM), time-of-flight secondary ion mass spectroscopy (ToF-SIMS) and infrared spectroscopy (FTIR). The supports with immobilised enzyme (urease) were also tested in combination with microreactors fabricated in silicon and Perspex, operating in a flow-through system. For microreactors filled with urease immobilised on glass beads (Sigma) and on polymeric beads (PAN), a very high and stable signal (pH change) was obtained. The developed method of urease immobilisation can be stated to be very effective.},
  subject      = {Biosensor},
  language  = {en}
}
@inproceedings{KraftNagl2003,
  author    = {Kraft, Bodo and Nagl, Manfred},
  title     = {Support of Conceptual Design in Civil Engineering by Graph-based Tools},
  year      = {2003},
  abstract  = {WS GTaD-2003 - The 1st Workshop on Graph Transformations and Design ed Grabska, E., Seite 6-7, Jagiellonian University Krakow. 2 pages},
  subject      = {CAD},
  language  = {de}
}
@inproceedings{SrivastavaSinghDhandetal.2006,
  author    = {Srivastava, Alok and Singh, Virendra and Dhand, Chetna and Kaur, Manindar and Singh, Tejvir and Witte, Katrin and Scherer, Ulrich W.},
  title     = {Study of swift heavy ion modified conduction polymer composites for application as gas sensor},
  url       = {http://nbn-resolving.de/urn:nbn:de:hbz:a96-opus-1345},
  year      = {2006},
  abstract  = {A polyaniline-based conducting composite was prepared by oxidative polymerisation of aniline in a polyvinylchloride (PVC) matrix. The coherent free standing thin films of the composite were prepared by a solution casting method. The polyvinyl chloride-polyaniline composites exposed to 120 MeV ions of silicon with total ion fluence ranging from 1011 to 1013 ions/cm2, were observed to be more sensitive towards ammonia gas than the unirradiated composite. The response time of the irradiated composites was observed to be comparably shorter. We report for the first time the application of swift heavy ion modified insulating polymer conducting polymer (IPCP) composites for sensing of ammonia gas.},
  subject      = {Biosensor},
  language  = {en}
}
@inproceedings{DigelTemizArtmannNojimaetal.2003,
  author    = {Digel, Ilya and Temiz Artmann, Ayseg{\"u}l and Nojima, H. and Artmann, Gerhard},
  title     = {Some peculiarities of application of cluster ions generated by plasma in respect of indoor air purification :[abstract]},
  year      = {2003},
  abstract  = {Recently, the SHARP Corporation, Japan, has developed the world's first "Plasma Cluster Ions (PCI)" air purification technology using plasma discharge to generate cluster ions. The new plasma cluster device releases positive and negative ions into the air, which are able to decompose and deactivate harmful airborne substances by chemical reactions. Because cluster ions consist of positive and negative ions that normally exist in the natural world, they are completely harmless and safe to humans. The amount of ozone generated by cluster ions is less than 0.01 ppm, which is significantly less than the 0.05-ppm standard for industrial operations and consumer electronics. This amount, thus, has no harming effects whatsoever on the human body. But particular properties and chemical processes in PCI treatment are still under study. It has been shown that PCI in most cases show strongly pronounced irreversible killing effects in respect of airborne microflora due to free-radical induced reactions and can be considered as a potent technology to disinfect both home, medical and industrial appliances.},
  subject      = {Clusterion},
  language  = {en}
}
@inproceedings{StaatDuong2016,
  author    = {Staat, Manfred and Duong, Minh Tuan},
  title     = {Smoothed Finite Element Methods for Nonlinear Solid Mechanics Problems: 2D and 3D Case Studies},
  series = {Proceedings of the National Science and Technology Conference on Mechanical - Transportation Engineering (NSCMET 2016), 13th October 2016, Hanoi, Vietnam, Vol.2},
  booktitle = {Proceedings of the National Science and Technology Conference on Mechanical - Transportation Engineering (NSCMET 2016), 13th October 2016, Hanoi, Vietnam, Vol.2},
  pages     = {440 -- 445},
  year      = {2016},
  abstract  = {The Smoothed Finite Element Method (SFEM) is presented as an edge-based and a facebased techniques for 2D and 3D boundary value problems, respectively. SFEMs avoid shortcomings of the standard Finite Element Method (FEM) with lower order elements such as overly stiff behavior, poor stress solution, and locking effects. Based on the idea of averaging spatially the standard strain field of the FEM over so-called smoothing domains SFEM calculates the stiffness matrix for the same number of degrees of freedom (DOFs) as those of the FEM. However, the SFEMs significantly improve accuracy and convergence even for distorted meshes and/or nearly incompressible materials. Numerical results of the SFEMs for a cardiac tissue membrane (thin plate inflation) and an artery (tension of 3D tube) show clearly their advantageous properties in improving accuracy particularly for the distorted meshes and avoiding shear locking effects.},
  language  = {en}
}
@inproceedings{FrotscherDuongStaat2015,
  author    = {Frotscher, Ralf and Duong, Minh Tuan and Staat, Manfred},
  title     = {Simulating beating cardiomyocytes with electromechanical coupling},
  series = {II. International Conference on Biomedical Technology : 28-30 October 2015 Hannover, Germany / T. Lenarz, P. Wriggers (Eds.)},
  booktitle = {II. International Conference on Biomedical Technology : 28-30 October 2015 Hannover, Germany / T. Lenarz, P. Wriggers (Eds.)},
  organization    = {International Conference on Biomedical Technology <2, 2015, Hannover>},
  pages     = {1 -- 2},
  year      = {2015},
  language  = {en}
}
@inproceedings{BarekFischerNavratiletal.2006,
  author    = {Barek, Jiri and Fischer, Jan and Navratil, Tomas and Peckova, Karolina and Yosypchuk, Bogdan},
  title     = {Silver solid amalgam electrodes as sensors for chemical carcinogens},
  url       = {http://nbn-resolving.de/urn:nbn:de:hbz:a96-opus-1554},
  year      = {2006},
  abstract  = {The applicability of differential pulse voltammetry (DPV) and adsorptive stripping voltammetry (AdSV) at a non-toxic meniscus-modified silver solid amalgam electrode (m-AgSAE) for the determination of trace amounts of genotoxic substances was demonstrated on the determination of micromolar and submicromolar concentrations of 3-nitrofluoranthene using methanol - 0.01 mol L-1 NaOH (9:1) mixture as a base electrolyte and of Ostazine Orange using 0.01 mol L-1 NaOH as a base electrolyte.},
  subject      = {Biosensor},
  language  = {en}
}