@inproceedings{WagnerSchoening2006,
  author    = {Wagner, Torsten and Sch{\"o}ning, Michael Josef},
  title     = {Preface of the Special Issue of I3S 2005 in J{\"u}lich (Germany)},
  url       = {http://nbn-resolving.de/urn:nbn:de:hbz:a96-opus-1365},
  year      = {2006},
  abstract  = {International Symposium on Sensor Science, I3S 2005 <3; 2005; Juelich, Germany> In: Sensors 2006, 6, 260-261 ISSN 1424-8220},
  subject      = {Biosensor},
  language  = {en}
}
@inproceedings{WagnerKohlFroebaetal.2006,
  author    = {Wagner, Thorsten and Kohl, Claus-Dieter and Fr{\"o}ba, Michael and Tiemann, Michael},
  title     = {Gas sensing properties of ordered mesoporous SnO2},
  url       = {http://nbn-resolving.de/urn:nbn:de:hbz:a96-opus-1422},
  year      = {2006},
  abstract  = {We report on the synthesis and CO gas-sensing properties of mesoporous tin(IV) oxides (SnO2). For the synthesis cetyltrimethylammonium bromide (CTABr) was used as a structure-directing agent; the resulting SnO2 powders were applied as films to commercially available sensor substrates by drop coating. Nitrogen physisorption shows specific surface areas up to 160 m2·g-1 and mean pore diameters of about 4 nm, as verified by TEM. The film conductance was measured in dependence on the CO concentration in humid synthetic air at a constant temperature of 300 °C. The sensors show a high sensitivity at low CO concentrations and turn out to be largely insensitive towards changes in the relative humidity. We compare the materials with commercially available SnO2-based sensors.},
  subject      = {Biosensor},
  language  = {en}
}
@inproceedings{UibelBlass2008,
  author    = {Uibel, Thomas and Blaß, Hans Joachim},
  title     = {Spaltverhalten von Holz beim Eindrehen von selbstbohrenden Holzschrauben},
  series = {Doktorandenkolloquium Holzbau Forschung und Praxis : Stuttgart, 05./06. M{\"a}rz 2008},
  booktitle = {Doktorandenkolloquium Holzbau Forschung und Praxis : Stuttgart, 05./06. M{\"a}rz 2008},
  editor    = {Kuhlmann, U.},
  publisher = {Univ., Inst. f{\"u}r Konstruktion und Entwurf},
  address   = {Stuttgart},
  pages     = {135 -- 142},
  year      = {2008},
  language  = {de}
}
@inproceedings{UibelBlass2010,
  author    = {Uibel, Thomas and Blaß, Hans Joachim},
  title     = {Determining Suitable Spacings and Distances for Self-tapping Screws by Experimental and Numerical Studies},
  series = {Proceedings of the 11th World Conference on Timber Engineering, WCTE 2010 : World Conference on Timber Engineering; [June 20 - 24, 2010, Riva del Garda, Trento, Italy] . Vol. III, Riva del Garda, Italy 2010},
  booktitle = {Proceedings of the 11th World Conference on Timber Engineering, WCTE 2010 : World Conference on Timber Engineering; [June 20 - 24, 2010, Riva del Garda, Trento, Italy] . Vol. III, Riva del Garda, Italy 2010},
  editor    = {Cecotti, A.},
  pages     = {669 -- 670},
  year      = {2010},
  language  = {en}
}
@inproceedings{UibelBlass2010,
  author    = {Uibel, Thomas and Blaß, Hans Joachim},
  title     = {A new method to determine suitable spacings and distances for self-tapping screws},
  series = {Meeting ... / International Council for Research and Innovation in Building and Construction, Working Commission W18 - Timber Structures},
  volume    = {43},
  booktitle = {Meeting ... / International Council for Research and Innovation in Building and Construction, Working Commission W18 - Timber Structures},
  publisher = {Lehrstuhl f{\"u}r Ingenieurholzbau und Baukonstruktionen},
  address   = {Karlsruhe},
  issn      = {1864-1784},
  year      = {2010},
  abstract  = {The determination of spacing, edge and end distance requirements for self-tapping screws requires numerous and comprehensive insertion tests. Yet the results of such tests cannot be transferred to other types of screws or even to screws of different diameter because of differences in shape or geometry. To reduce the effort of insertion tests a new method was developed which allows the estimation of required spacings, distances and timber thickness.},
  language  = {en}
}
@inproceedings{Uibel2007,
  author    = {Uibel, Thomas},
  title     = {Brettsperrholz - Verbindungen mit mechanischen Verbindungsmitteln},
  series = {Ingenieurholzbau, Karlsruher Tage 2007 : Forschung f{\"u}r die Praxis; 4. und 5. Oktober 2007; Tagungsband / Universit{\"a}t Karlsruhe (TH), Lehrstuhl f{\"u}r Ingenieurholzbau und Baukonstruktionen},
  booktitle = {Ingenieurholzbau, Karlsruher Tage 2007 : Forschung f{\"u}r die Praxis; 4. und 5. Oktober 2007; Tagungsband / Universit{\"a}t Karlsruhe (TH), Lehrstuhl f{\"u}r Ingenieurholzbau und Baukonstruktionen},
  publisher = {Bruder-Verlag},
  address   = {K{\"o}ln},
  pages     = {62 -- 73},
  year      = {2007},
  language  = {de}
}
@inproceedings{Uibel2009,
  author    = {Uibel, Thomas},
  title     = {Beurteilung der Spaltgefahr beim Eindrehen von selbstbohrenden Holzschrauben},
  series = {Forum Holz/Bau Garmisch 09 : Internationales Holzbauforum (IHF) ; Congress Centrum, Garmisch-Partenkirchen, 2. - 4. Dezember 2009 ; aus der Praxis - f{\"u}r die Praxis, Wirtschaft, Markt, {\"O}kologie, Energieeffizienz, Architektur, Tragwerke, Realisierungen},
  booktitle = {Forum Holz/Bau Garmisch 09 : Internationales Holzbauforum (IHF) ; Congress Centrum, Garmisch-Partenkirchen, 2. - 4. Dezember 2009 ; aus der Praxis - f{\"u}r die Praxis, Wirtschaft, Markt, {\"O}kologie, Energieeffizienz, Architektur, Tragwerke, Realisierungen},
  publisher = {Fraunhofer IRB},
  address   = {Stuttgart},
  isbn      = {978-3-8167-8187-5},
  year      = {2009},
  language  = {de}
}
@inproceedings{Tuerk2006,
  author    = {T{\"u}rk, Roman},
  title     = {Sanierung von Hausanschl{\"u}ssen},
  year      = {2006},
  abstract  = {In: Alfha.net / Sektion Bauingenieurwesen: 1. [Erster] Erfahrungsaustausch : Absolventen des Fachbereichs Bauingenieurwesens berichten. 13. Oktober 2006. S. 23-24. Zusammenfassung des Vortrags.},
  subject      = {Hausanschluss},
  language  = {de}
}
@inproceedings{TymeckiGlabKoncki2006,
  author    = {Tymecki, Lukasz and Glab, Stanislaw and Koncki, Robert},
  title     = {Miniaturized, planar ion-selective electrodes fabricated by means of thick-film technology},
  url       = {http://nbn-resolving.de/urn:nbn:de:hbz:a96-opus-1506},
  year      = {2006},
  abstract  = {Various planar technologies are employed for developing solid-state sensors having low cost, small size and high reproducibility; thin- and thick-film technologies are most suitable for such productions. Screen-printing is especially suitable due to its simplicity, low-cost, high reproducibility and efficiency in large-scale production. This technology enables the deposition of a thick layer and allows precise pattern control. Moreover, this is a highly economic technology, saving large amounts of the used inks. In the course of repetitions of the film-deposition procedure there is no waste of material due to additivity of this thick-film technology. Finally, the thick films can be easily and quickly deposited on inexpensive substrates. In this contribution, thick-film ion-selective electrodes based on ionophores as well as crystalline ion-selective materials dedicated for potentiometric measurements are demonstrated. Analytical parameters of these sensors are comparable with those reported for conventional potentiometric electrodes. All mentioned thick-film strip electrodes have been totally fabricated in only one, fully automated thickfilm technology, without any additional manual, chemical or electrochemical steps. In all cases simple, inexpensive, commercially available materials, i.e. flexible, plastic substrates and easily cured polymer-based pastes were used.},
  subject      = {Biosensor},
  language  = {en}
}
@inproceedings{TranStaatKreissig2007,
  author    = {Tran, Thanh Ngoc and Staat, Manfred and Kreißig, R.},
  title     = {Calculation of load carrying capacity of shell structures with elasto-plastic material by direct methods},
  year      = {2007},
  abstract  = {Proceedings of the International Conference on Material Theory and Nonlinear Dynamics. MatDyn. Hanoi, Vietnam, Sept. 24-26, 2007, 8 p. In this paper, a method is introduced to determine the limit load of general shells using the finite element method. The method is based on an upper bound limit and shakedown analysis with elastic-perfectly plastic material model. A non-linear constrained optimisation problem is solved by using Newton's method in conjunction with a penalty method and the Lagrangean dual method. Numerical investigation of a pipe bend subjected to bending moments proves the effectiveness of the algorithm.},
  subject      = {Finite-Elemente-Methode},
  language  = {en}
}