@inproceedings{KernHeidlerSeeversetal.2004,
  author    = {Kern, Alexander and Heidler, Fridolin and Seevers, M. and Zischank, Wolfgang J.},
  title     = {Magnetic Fields and Induced Voltages in case of a Direct Strike - Comparison of Results obtained from Measurements at a Scaled Building to those of IEC 62305-4},
  isbn      = {0304-3886},
  year      = {2004},
  abstract  = {In the paper the results obtained from experiments at a modelled reinforced building in case of a direct lightning strike are compared with calculations. The comparison includes peak values of the magnetic field Hmax, its derivative (dH/dt)max and of induced voltages umax in typical cable routings. The experiments are performed at a 1:6 scaled building and the results are extrapolated using the similarity relations theory. The calculations are based on the approximate formulae given in IEC 62305-4 and have to be supplemented by a rough estimation of the additional shielding effect of a second reinforcement layer. The comparison shows, that the measured peak values of the magnetic field and its derivative are mostly lower than the calculated. The induced voltages are in good agreement. Hence, calculations of the induced voltages based on IEC 62305-4 are a good method for lightning protection studies of buildings, where the reinforcement is used as a grid-like electromagnetic shield.},
  subject      = {Blitz},
  language  = {en}
}
@inproceedings{ZischankHeidlerWiesingeretal.2004,
  author    = {Zischank, Wolfgang J. and Heidler, Fridolin and Wiesinger, J. and Stimper, K. and Kern, Alexander and Seevers, M.},
  title     = {Magnetic Fields and Induced Voltages inside LPZ 1 Measured at a 1:6 Scale Model Building},
  year      = {2004},
  abstract  = {Laborexperimente zu Blitzschutzzonen in Stahlbetongeb{\"a}uden anhand eines Modells im Maßstab 1:6},
  language  = {en}
}
@article{VuStaat2004,
  author    = {Vu, Duc-Khoi and Staat, Manfred},
  title     = {An algorithm for shakedown analysis of structure with temperature dependent yield stress},
  year      = {2004},
  abstract  = {This work is an attempt to answer the question: How to use convex programming in shakedown analysis of structures made of materials with temperature-dependent properties. Based on recently established shakedown theorems and formulations, a dual relationship between upper and lower bounds of the shakedown limit load is found, an algorithmfor shakedown analysis is proposed. While the original problem is neither convex nor concave, the algorithm presented here has the advantage of employing convex programming tools.},
  subject      = {Einspielen <Werkstoff>},
  language  = {en}
}
@article{KuehnHaugnerStaatetal.2004,
  author    = {K{\"u}hn, Raoul-Roman and Haugner, Werner and Staat, Manfred and Sponagel, Stefan},
  title     = {A Two Phase Mixture Model based on Bone Observation},
  year      = {2004},
  abstract  = {An optimization method is developed to describe the mechanical behaviour of the human cancellous bone. The method is based on a mixture theory. A careful observation of the behaviour of the bone material leads to the hypothesis that the bone density is controlled by the principal stress trajectories (Wolff's law). The basic idea of the developed method is the coupling of a scalar value via an eigenvalue problem to the principal stress trajectories. On the one hand this theory will permit a prediction of the reaction of the biological bone structure after the implantation of a prosthesis, on the other hand it may be useful in engineering optimization problems. An analytical example shows its efficiency.},
  subject      = {Knochen},
  language  = {en}
}
@inproceedings{KraftNagl2003,
  author    = {Kraft, Bodo and Nagl, Manfred},
  title     = {Semantic tool support for conceptual design},
  year      = {2003},
  abstract  = {ITCE-2003 - 4th Joint Symposium on Information Technology in Civil Engineering ed Flood, I., Seite 1-12, ASCE (CD-ROM), Nashville, USA In this paper we discussed graph based tools to support architects during the conceptual design phase. Conceptual Design is defined before constructive design; the used concepts are more abstract. We develop two graph based approaches, a topdown using the graph rewriting system PROGRES and a more industrially oriented approach, where we extend the CAD system ArchiCAD. In both approaches, knowledge can be defined by a knowledge engineer, in the top-down approach in the domain model graph, in the bottom-up approach in the in an XML file. The defined knowledge is used to incrementally check the sketch and to inform the architect about violations of the defined knowledge. Our goal is to discover design error as soon as possible and to support the architect to design buildings with consideration of conceptual knowledge.},
  subject      = {CAD},
  language  = {en}
}
@inproceedings{DigelTemizArtmannArtmannetal.2003,
  author    = {Digel, Ilya and Temiz Artmann, Ayseg{\"u}l and Artmann, Gerhard and Nojima, H.},
  title     = {Plasma cluster ions (PCI) influence on microbial cells viability : [abstract]},
  year      = {2003},
  abstract  = {Recently, SHARP corporation has developed the world's first "Plasma Cluster Ions (PCI)" air purification technology, which uses plasma discharge to generate cluster ions. The new plasma cluster device releases into the air positive and negative ions, which are harmless to humans and are able to decompose and deactivate airborne substances by chemical reactions. A lot of phenomenological tests of the PCI air purification technology on microbial cells have been conducted. And, in most cases, it has been shown that PCI demonstrate strongly pronounced killing effect. Although, the particular mechanisms of PCI action are still not evident. We studied variations in resistance to PCI among gram-positive airborne microorganisms, as well as some dose-dependent, spatial, cultural and biochemical properties of PCI action in respect of Staphylococcus spp, Enterococcus spp, Micrococcus spp.},
  subject      = {Clusterion},
  language  = {en}
}
@inproceedings{DigelTemizArtmannNojimaetal.2003,
  author    = {Digel, Ilya and Temiz Artmann, Ayseg{\"u}l and Nojima, H. and Artmann, Gerhard},
  title     = {Effects of plasma generated ions on bacteria : [poster]},
  year      = {2003},
  abstract  = {Summary and Conclusions PCIs were clearly effective in terms of their antibacterial effects with the strains tested. This efficacy increased with the time the bacteries were exposed to PCIs. The bactericidal action has proved to be irreversible. PCIs were significantly less effective in shadowed areas. PCI exposure caused multiple protein damages as observed in SDS PAGE studies. There was no single but multiple molecular mechanism causing the bacterial death.},
  subject      = {Clusterion},
  language  = {en}
}
@inproceedings{DigelTemizArtmannNojimaetal.2003,
  author    = {Digel, Ilya and Temiz Artmann, Ayseg{\"u}l and Nojima, H. and Artmann, Gerhard},
  title     = {Some peculiarities of application of cluster ions generated by plasma in respect of indoor air purification :[abstract]},
  year      = {2003},
  abstract  = {Recently, the SHARP Corporation, Japan, has developed the world's first "Plasma Cluster Ions (PCI)" air purification technology using plasma discharge to generate cluster ions. The new plasma cluster device releases positive and negative ions into the air, which are able to decompose and deactivate harmful airborne substances by chemical reactions. Because cluster ions consist of positive and negative ions that normally exist in the natural world, they are completely harmless and safe to humans. The amount of ozone generated by cluster ions is less than 0.01 ppm, which is significantly less than the 0.05-ppm standard for industrial operations and consumer electronics. This amount, thus, has no harming effects whatsoever on the human body. But particular properties and chemical processes in PCI treatment are still under study. It has been shown that PCI in most cases show strongly pronounced irreversible killing effects in respect of airborne microflora due to free-radical induced reactions and can be considered as a potent technology to disinfect both home, medical and industrial appliances.},
  subject      = {Clusterion},
  language  = {en}
}
@inproceedings{DigelTemizArtmannNojimaetal.2003,
  author    = {Digel, Ilya and Temiz Artmann, Ayseg{\"u}l and Nojima, H. and Artmann, Gerhard},
  title     = {Plasma-generated cluster ions' effects on indoor microflora : [abstract]},
  year      = {2003},
  abstract  = {Recently, SHARP corporation has developed the world's first "Plasma Cluster Ions® (PCI)" air purification technology, which uses plasma discharge to generate cluster ions. The new Plasma Cluster Device releases positive and negative ions into the air, which are harmless to humans and are able to decompose and deactivate airborne substances by chemical reactions. In the past, phenomenological tests on the efficacy of the PCI air purification technology on microbial cells have been conducted. In most cases, it has been shown that PCI demonstrated strongly pronounced killing effects on microorganisms. However, the particular mechanisms of PCI action still have to be uncovered.},
  subject      = {Clusterion},
  language  = {en}
}
@inproceedings{SedlacekGesslerSchleseretal.2003,
  author    = {Sedlacek, G. and Geßler, A. and Schleser, Markus and Mund, F. and V{\"o}lling, B.},
  title     = {Verbindungen vorgefertigter Textilbetonbauteile},
  series = {Textile reinforced structures : proceedings of the 2nd Colloquium on Textile Reinforced Structures (CTRS2), Dresden, Germany, 29.9. - 1.10.2003},
  booktitle = {Textile reinforced structures : proceedings of the 2nd Colloquium on Textile Reinforced Structures (CTRS2), Dresden, Germany, 29.9. - 1.10.2003},
  publisher = {Techn. Univ.},
  address   = {Dresden},
  organization    = {Colloquium on Textile Reinforced Structures <2, 2003, Dresden>},
  isbn      = {3-86005-386-8},
  pages     = {481 -- 493},
  year      = {2003},
  language  = {en}
}
@article{BaroudWuBohneretal.2003,
  author    = {Baroud, G. and Wu, J.Z. and Bohner, M and Sponagel, Stefan and Steffen, T.},
  title     = {How to determine the permeability for cement infiltration into osteoporotic cancellous bone},
  series = {Medical Engineering \& Physics. 25 (2003), H. 4},
  journal   = {Medical Engineering \& Physics. 25 (2003), H. 4},
  issn      = {1350-4533},
  pages     = {283 -- 288},
  year      = {2003},
  abstract  = {Cement augmentation is an emerging surgical procedure in which bone cement is used to infiltrate and reinforce osteoporotic vertebrae. Although this infiltration procedure has been widely applied, it is performed empirically and little is known about the flow characteristics of cement during the injection process. We present a theoretical and experimental approach to investigate the intertrabecular bone permeability during the infiltration procedure. The cement permeability was considered to be dependent on time, bone porosity, and cement viscosity in our analysis. In order to determine the time-dependent permeability, ten cancellous bone cores were harvested from osteoporotic vertebrae, infiltrated with acrylic cement at a constant flow rate, and the pressure drop across the cores during the infiltration was measured. The viscosity dependence of the permeability was determined based on published experimental data. The theoretical model for the permeability as a function of bone porosity and time was then fit to the testing data. Our findings suggest that the intertrabecular bone permeability depends strongly on time. For instance, the initial permeability (60.89 mm4/N.s) reduced to approximately 63\% of its original value within 18 seconds. This study is the first to analyze cement flow through osteoporotic bone. The theoretical and experimental models provided in this paper are generic. Thus, they can be used to systematically study and optimize the infiltration process for clinical practice.},
  subject      = {Osteoporose},
  language  = {en}
}
@article{Staat2003,
  author    = {Staat, Manfred},
  title     = {Shakedown and ratchetting under tension-torsion loadings: analysis and experiments},
  year      = {2003},
  abstract  = {Structural design analyses are conducted with the aim of verifying the exclusion of ratchetting. To this end it is important to make a clear distinction between the shakedown range and the ratchetting range. The performed experiment comprised a hollow tension specimen which was subjected to alternating axial forces, superimposed with constant moments. First, a series of uniaxial tests has been carried out in order to calibrate a bounded kinematic hardening rule. The load parameters have been selected on the basis of previous shakedown analyses with the PERMAS code using a kinematic hardening material model. It is shown that this shakedown analysis gives reasonable agreement between the experimental and the numerical results. A linear and a nonlinear kinematic hardening model of two-surface plasticity are compared in material shakedown analysis.},
  subject      = {Einspielen <Werkstoff>},
  language  = {en}
}
@inproceedings{Staat2003,
  author    = {Staat, Manfred},
  title     = {Design by Analysis of Pressure Components by non-linear Optimization},
  year      = {2003},
  abstract  = {This paper presents the direct route to Design by Analysis (DBA) of the new European pressure vessel standard in the language of limit and shakedown analysis (LISA). This approach leads to an optimization problem. Its solution with Finite Element Analysis is demonstrated for some examples from the DBA-Manual. One observation from the examples is, that the optimisation approach gives reliable and close lower bound solutions leading to simple and optimised design decision.},
  language  = {en}
}
@article{KaemperPicardBrilletal.2003,
  author    = {K{\"a}mper, Klaus-Peter and Picard, Antoni and Brill, Manfred and Cassel, Detlev and Jentsch, Andreas and Merten, Sabine and Rollwa, Markus},
  title     = {The Virtual Clean Room - a new tool in teaching MST process technologies},
  year      = {2003},
  abstract  = {The Virtual Clean Room - a new tool in teaching MST process technologies University education in high-technology fields like MST is not complete without intensive laboratory sessions. Students cannot fully grasp the complexity and the special problems related to the manufacturing of microsystems without a thorough hands-on experience in a MST clean room.},
  subject      = {Virtuelle Maschine},
  language  = {en}
}
@inproceedings{ButenwegKuhlmannLopezetal.2003,
  author    = {Butenweg, Christoph and Kuhlmann, Winfried and Lopez, M. and Fernandez, S.},
  title     = {Seismic vulnerability assessment of the Aachen Cathedral based on measurements and numerical simulations},
  series = {International Conference on Earthquake Engineering to mark 40 years from Catastrophic 1963 Skopje Earthquake, Skopje 2003},
  booktitle = {International Conference on Earthquake Engineering to mark 40 years from Catastrophic 1963 Skopje Earthquake, Skopje 2003},
  organization    = {International conference in earthquake engineering to mark 40 years from catastrophic 1963 Skopje earthquake <2003, Skopje>},
  pages     = {1 -- 8},
  year      = {2003},
  language  = {en}
}
@inproceedings{KraftMeyerNagl2002,
  author    = {Kraft, Bodo and Meyer, Oliver and Nagl, Manfred},
  title     = {Graph technology support for conceptual design in civil engineering},
  isbn      = {3-18-318004-9},
  year      = {2002},
  abstract  = {In: Advances in intelligent computing in engineering : proceedings of the 9.International EG-ICE Workshop ; Darmstadt, (01 - 03 August) 2002 / Martina Schnellenbach-Held ... (eds.) . - D{\"u}sseldorf: VDI-Verl., 2002 .- Fortschritt-Berichte VDI, Reihe 4, Bauingenieurwesen ; 180 ; S. 1-35 The paper describes a novel way to support conceptual design in civil engineering. The designer uses semantical tools guaranteeing certain internal structures of the design result but also the fulfillment of various constraints. Two different approaches and corresponding tools are discussed: (a) Visually specified tools with automatic code generation to determine a design structure as well as fixing various constraints a design has to obey. These tools are also valuable for design knowledge specialist. (b) Extensions of existing CAD tools to provide semantical knowledge to be used by an architect. It is sketched how these different tools can be combined in the future. The main part of the paper discusses the concepts and realization of two prototypes following the two above approaches. The paper especially discusses that specific graphs and the specification of their structure are useful for both tool realization projects.},
  subject      = {CAD},
  language  = {en}
}
@inproceedings{StaatHeitzer2002,
  author    = {Staat, Manfred and Heitzer, Michael},
  title     = {The restricted influence of kinematic hardening on shakedown loads},
  year      = {2002},
  abstract  = {Structural design analyses are conducted with the aim of verifying the exclusion of ratcheting. To this end it is important to make a clear distinction between the shakedown range and the ratcheting range. In cyclic plasticity more sophisticated hardening models have been suggested in order to model the strain evolution observed in ratcheting experiments. The hardening models used in shakedown analysis are comparatively simple. It is shown that shakedown analysis can make quite stable predictions of admissible load ranges despite the simplicity of the underlying hardening models. A linear and a nonlinear kinematic hardening model of two-surface plasticity are compared in material shakedown analysis. Both give identical or similar shakedown ranges. Structural shakedown analyses show that the loading may have a more pronounced effect than the hardening model.},
  subject      = {Biomedizinische Technik},
  language  = {en}
}
@inproceedings{DarvenizaFlisowskiKernetal.2002,
  author    = {Darveniza, M. and Flisowski, Z. and Kern, Alexander and Landers, E.-U. and LoPiparo, G. and Mazzetti, C. and Rousseau, A. and Sherlock, J.},
  title     = {Application problems of the probabilistic approach to the assessment of risk for structures and services},
  year      = {2002},
  abstract  = {The paper deals with the development of the probabilistic approach to the assessment of risk due to lightning. Sources of damage, types of damage and types of loss are defined and, accordingly, the procedure for risk analysis and the way of assessment of different risk components is proposed. The way to evaluate the influence of different protection measures (lightning protection system; shielding of structure, cables and equipment; routing of internal wiring; surge protective device) in reducing such probabilities is considered. The paper has been prepared within the framework of the activity of IEC TC81-WG9/CLC TC81-WG4 directed to prepare the draft IEC 62305-2 Risk Management, in cooperation with the Secretary of IEC/CLC TC81.},
  language  = {en}
}
@inproceedings{KernKrichel2002,
  author    = {Kern, Alexander and Krichel, Frank},
  title     = {Considerations about the lightning protection system of mains independent renewable energy hybrid-systems - practical experiences},
  year      = {2002},
  abstract  = {In the paper a lightning protection design concept for renewable energy hybrid-systems without power mains connection is described. Based on a risk analysis protection measures against direct strikes and overvoltages are shown in an overview. The design concept is realized exemplarily for the hybrid-system VATALI on the Greek island Crete. VATALI, not lightning protected at that time, was a victim of a lightning strike in the year 2000 causing destructions and damages of some mechanical and electrical components with costs of approx. 60.000 €. The hardware costs for the protection measures were about 15.000 €: about 50\% of the costs are due to protection measures against direct strikes, 50\% are due to overvoltage protection.},
  language  = {en}
}
@inproceedings{ZischankHeidlerKernetal.2002,
  author    = {Zischank, Wolfgang J. and Heidler, Fridolin and Kern, Alexander and Metwally, I. A. and Wiesinger, J. and Seevers, M.},
  title     = {Laboratory simulation of direct lightning strokes to a modelled building - measurement of magnetic fields and induced voltages},
  year      = {2002},
  abstract  = {In IEC 61312-2 equations for the assessment of the magnetic fields inside structures due to a direct lightning strike are given. These equations are based on computer simulations for shields consisting of a single-layer steel grid of a given mesh width. Real constructions, however, contain at least two layers of reinforcement steel grids. The objective of this study was to experimentally determine the additional shielding effectiveness of a second reinforcement layer compared to a single-layer grid. To this end, simulated structures were set up in the high current laboratory. The structures consisted of cubic cages of 2 m side length with one or with two reinforcement grids, respectively. The structures were exposed to direct lightning currents representing the variety of anticipated lightning current waveforms. The magnetic fields and their derivatives at several positions inside the structure as well as the voltage between "floor" and "roof" in the center were determined for different current injection points. From these data the improvement of the shielding caused by a second reinforcement layer is derived.},
  language  = {en}
}