@article{BaringhausGaigall2018,
  author    = {Baringhaus, Ludwig and Gaigall, Daniel},
  title     = {Efficiency comparison of the Wilcoxon tests in paired and independent survey samples},
  series = {Metrika},
  volume    = {2018},
  journal   = {Metrika},
  number    = {81},
  publisher = {Springer},
  address   = {Berlin},
  issn      = {1435-926X},
  doi       = {10.1007/s00184-018-0661-4},
  pages     = {891 -- 930},
  year      = {2018},
  abstract  = {The efficiency concepts of Bahadur and Pitman are used to compare the Wilcoxon tests in paired and independent survey samples. A comparison through the length of corresponding confidence intervals is also done. Simple conditions characterizing the dominance of a procedure are derived. Statistical tests for checking these conditions are suggested and discussed.},
  language  = {de}
}
@article{ButenwegMarinkovićKubalskietal.2018,
  author    = {Butenweg, Christoph and Marinković, Marko and Kubalski, Thomas and Fehling, Ekkehard and Pfetzing, Thomas and Meyer, Udo},
  title     = {Auslegung von Stahlbetonrahmentragwerken mit Ausfachungen aus Ziegelmauerwerk (Teil 1)},
  series = {Ziegelindustrie international : ZI = Brick and tile industry international},
  journal   = {Ziegelindustrie international : ZI = Brick and tile industry international},
  number    = {4},
  editor    = {Voss, Michael},
  publisher = {Bauverlag BV GmbH},
  address   = {G{\"u}tersloh},
  issn      = {0341-0552},
  pages     = {30 -- 39},
  year      = {2018},
  abstract  = {Im Rahmen des europ{\"a}ischen Verbundprojekts INSYSME wurden von den deutschen Partnern die Systeme IMES und INODIS zur Verbesserung des seismischen Verhaltens von ausgefachten Stahlbetonrahmen entwickelt. Ziel beider Systeme ist es, Stahlbetonrahmen und Ausfachung zu entkoppeln, anstatt die Tragf{\"a}higkeit durch aufwendige und kostspielige zus{\"a}tzliche Bewehrungseinlagen zu erh{\"o}hen. Erste Ergebnisse des Systems IMES f{\"u}r Belastungen in und senkrecht zu der Wandebene werden vorgestellt.},
  language  = {de}
}
@article{ButenwegMarinkovićKubalskietal.2018,
  author    = {Butenweg, Christoph and Marinković, Marko and Kubalski, Thomas and Fehling, Ekkehard and Pfetzing, Thomas and Meyer, Udo},
  title     = {Auslegung von Stahlbetonrahmentragwerken mit Ausfachungen aus Ziegelmauerwerk (Teil 2)},
  series = {Ziegelindustrie international : ZI = Brick and tile industry international},
  journal   = {Ziegelindustrie international : ZI = Brick and tile industry international},
  number    = {6},
  editor    = {Voss, Michael},
  publisher = {Bauverlag BV GmbH},
  address   = {G{\"u}tersloh},
  issn      = {0341-0552},
  pages     = {24 -- 43},
  year      = {2018},
  abstract  = {Im Rahmen des europ{\"a}ischen Verbundprojekts INSYSME wurden von den deutschen Partnern die Systeme IMES und INODIS zur Verbesserung des seismischen Verhaltens von ausgefachten Stahlbetonrahmen entwickelt. Ziel beider Systeme ist es, Stahlbetonrahmen und Ausfachung zu entkoppeln, anstatt die Tragf{\"a}higkeit durch aufwendige und kostspielige zus{\"a}tzliche Bewehrungseinlagen zu erh{\"o}hen. Erste Ergebnisse des Systems IMES f{\"u}r Belastungen in und senkrecht zu der Wandebene werden vorgestellt.},
  language  = {de}
}
@inproceedings{Gross2018,
  author    = {Groß, Rolf Fritz},
  title     = {M{\"o}glichkeiten und Grenzen f{\"u}r Forschung an Fachhochschulen},
  series = {Smart Building Convention und BIMconvention in Aachen im September},
  booktitle = {Smart Building Convention und BIMconvention in Aachen im September},
  pages     = {19 Seiten},
  year      = {2018},
  language  = {de}
}
@article{RabehiGarlanAchtsnichtetal.2018,
  author    = {Rabehi, Amine and Garlan, Benjamin and Achtsnicht, Stefan and Krause, Hans-Joachim and Offenh{\"a}usser, Andreas and Ngo, Kieu and Neveu, Sophie and Graff-Dubois, Stephanie and Kokabi, Hamid},
  title     = {Magnetic detection structure for Lab-on-Chip applications based on the frequency mixing technique},
  series = {Sensors},
  volume    = {18},
  journal   = {Sensors},
  number    = {6},
  publisher = {MDPI},
  address   = {Basel},
  issn      = {1424-8220},
  doi       = {10.3390/s18061747},
  pages     = {14 Seiten},
  year      = {2018},
  abstract  = {A magnetic frequency mixing technique with a set of miniaturized planar coils was investigated for use with a completely integrated Lab-on-Chip (LoC) pathogen sensing system. The system allows the detection and quantification of superparamagnetic beads. Additionally, in terms of magnetic nanoparticle characterization ability, the system can be used for immunoassays using the beads as markers. Analytical calculations and simulations for both excitation and pick-up coils are presented; the goal was to investigate the miniaturization of simple and cost-effective planar spiral coils. Following these calculations, a Printed Circuit Board (PCB) prototype was designed, manufactured, and tested for limit of detection, linear response, and validation of theoretical concepts. Using the magnetic frequency mixing technique, a limit of detection of 15 µg/mL of 20 nm core-sized nanoparticles was achieved without any shielding.},
  language  = {en}
}
@misc{RossJonesTeumerCapitainetal.2018,
  author    = {Ross-Jones, J. and Teumer, T. and Capitain, C. and Tippk{\"o}tter, Nils and Krause, M. J. and Methner, F.-J. and R{\"a}dle, M.},
  title     = {Analytical methods for in-line characterization of beer haze},
  series = {Trends in Brewing},
  journal   = {Trends in Brewing},
  year      = {2018},
  abstract  = {In most beers, producers strive to minimize haze to maximize visual appeal. To detect the formation of particulates, a measurement system for sub-micron particles is required. Beer haze is naturally occurring, composed of protein or polyphenol particles; in their early stage of growth their size is smaller than 2 µm. Microscopy analysis is time and resource intensive; alternatively, backscattering is an inexpensive option for detecting particle sizes of interest.},
  language  = {en}
}
@misc{CapitainLukebaUlberetal.2018,
  author    = {Capitain, C. C. and Lukeba, L. and Ulber, Roland and Tippk{\"o}tter, Nils},
  title     = {Biomimetische Klebstoffe aus Organosolv-Lignin},
  series = {Chemie Ingenieur Technik},
  volume    = {90},
  journal   = {Chemie Ingenieur Technik},
  number    = {9},
  publisher = {Wiley-VCH},
  address   = {Weinheim},
  issn      = {0009-286X},
  doi       = {10.1002/cite.201855076},
  pages     = {1167},
  year      = {2018},
  abstract  = {Aufgrund von EU-Regularien und Umweltinitiativen w{\"a}chst der Markt f{\"u}r nachhaltige und abbaubare Klebstoffe stetig. Organosolv (OS)-Lignin ist ein kommerziell wenig ertragreicher Nebenstrom der Lignocellulose-Bioraffinerie. Durch das "Nachahmen" der Adh{\"a}sionseigenschaften mit strukturverwandten Muschel-Aminos{\"a}uren soll OS-Lignin in einen starkes, vollst{\"a}ndig biobasiertes Adh{\"a}siv umgewandelt werden. Funktionsweisend f{\"u}r die Adh{\"a}sion des Muschelklebstoffes ist die Catecholgruppe der Aminos{\"a}ure L-DOPA. Die laccase-katalysierte Polymerisationsreaktion von Lignin und L-DOPA ist schwierig zu kontrollieren, da L-DOPA eine Ringschlussreaktion eingeht. Stattdessen wurde eine zweistufige Reaktion mit einem Diamin als Ankermolek{\"u}l etabliert. Die Catecholgruppe, die im zweiten Schritt enzymatisch an das Lignin-Amin gebunden wird, kann durch Komplexbildung mit Fe(III)-Ionen sowohl zur Adh{\"a}sion als auch zur Koh{\"a}sion des Klebstoffes beitragen. Der Lignin-Catechol-Klebstoff ist frei von petrochemischen Chemikalien und biologisch abbaubar. In ersten Stirnzugversuchen konnte eine Haftkraft von 0,3 MPa erreicht werden.},
  language  = {de}
}
@misc{EngelBayerUlberetal.2018,
  author    = {Engel, M. and Bayer, H. and Ulber, Roland and Tippk{\"o}tter, Nils},
  title     = {Kommt es in Elektrofermentationen mit Clostridium acetobutylicum zu einer Eisenlimitierung?},
  series = {Chemie Ingenieur Technik},
  volume    = {90},
  journal   = {Chemie Ingenieur Technik},
  number    = {9},
  publisher = {Wiley-VCH},
  address   = {Weinheim},
  issn      = {0009-286X},
  doi       = {10.1002/cite.201855047},
  pages     = {1154},
  year      = {2018},
  abstract  = {Das strikt anaerobe Bakterium Clostridium acetobutylicum bildet die L{\"o}semittel Aceton, Butanol und Ethanol (ABE-Fermentation). Im Fall einer Eisenlimitierung kommt es zus{\"a}tzlich zu einer Riboflavinsekretion (RF), was durch die gelbe F{\"a}rbung des Kultur{\"u}berstands erkennbar ist. In dieser Arbeit wurde beobachtet, dass w{\"a}hrend Elektrofermentationen mit C. acetobutylicum bei -600 mV eine gelbe F{\"a}rbung auftritt. Es wurde deshalb untersucht, ob eine Eisenlimitierung im bio-elektrochemischen System (BES) vorliegt. Hierzu wurden die Flavinspezien bei Kultivierungen in Medien mit einer Eisenlimitierung bzw. mit ausreichend Eisen in Serumflaschen sowie im BES mit und ohne angelegtem Potenzial verglichen. In den Serumflaschenversuchen wurden RF und Flavinadenindinukleotid (FAD)-Konzentrationen von ‡ 20 mg L⁻¹ sowie Flavinmononukleotid (FMN)-Konzentrationen von ca. 5 mg L⁻¹ detektiert. Bei ausreichender Eisenverf{\"u}gbarkeit hingegen wurden in den Serumflaschen fast keine Flavine sekretiert. Im BES bei -600 mV hingegen wurde auch in diesen Kultur{\"u}berst{\"a}nden FMN und FAD (1-5 mg L⁻¹ ),jedoch kein RF gemessen. Diese Ergebnisse zeigen, dass die Flavinbildung im BES mit angelegtem Potenzial nicht mit der Flavinbildung unter Eisenlimitierung in Serumflaschen korreliert. Andere Faktoren f{\"u}r eine m{\"o}gliche Flavinbildung werden aktuell n{\"a}her betrachtet.},
  language  = {de}
}
@article{KetelhutGoellBraunsteinetal.2018,
  author    = {Ketelhut, Maike and G{\"o}ll, Fabian and Braunstein, Bj{\"o}rn and Albracht, Kirsten and Abel, Dirk},
  title     = {Comparison of different training algorithms for the leg extension training with an industrial robot},
  series = {Current Directions in Biomedical Engineering},
  volume    = {4},
  journal   = {Current Directions in Biomedical Engineering},
  number    = {1},
  publisher = {De Gruyter},
  address   = {Berlin},
  issn      = {2364-5504},
  doi       = {10.1515/cdbme-2018-0005},
  pages     = {17 -- 20},
  year      = {2018},
  abstract  = {In the past, different training scenarios have been developed and implemented on robotic research platforms, but no systematic analysis and comparison have been done so far. This paper deals with the comparison of an isokinematic (motion with constant velocity) and an isotonic (motion against constant weight) training algorithm. Both algorithms are designed for a robotic research platform consisting of a 3D force plate and a high payload industrial robot, which allows leg extension training with arbitrary six-dimensional motion trajectories. In the isokinematic as well as the isotonic training algorithm, individual paths are defined i n C artesian s pace by sufficient s upport p oses. I n t he i sotonic t raining s cenario, the trajectory is adapted to the measured force as the robot should only move along the trajectory as long as the force applied by the user exceeds a minimum threshold. In the isotonic training scenario however, the robot's acceleration is a function of the force applied by the user. To validate these findings, a simulative experiment with a simple linear trajectory is performed. For this purpose, the same force path is applied in both training scenarios. The results illustrate that the algorithms differ in the force dependent trajectory adaption.},
  language  = {en}
}
@article{WerkhausenAlbrachtCroninetal.2018,
  author    = {Werkhausen, Amelie and Albracht, Kirsten and Cronin, Neil J and Paulsen, G{\o}ran and Bojsen-M{\o}ller, Jens and Seynnes, Olivier R},
  title     = {Effect of training-induced changes in achilles tendon stiffness on muscle-tendon behavior during landing},
  series = {Frontiers in physiology},
  journal   = {Frontiers in physiology},
  number    = {9},
  publisher = {Frontiers Research Foundation},
  address   = {Lausanne},
  issn      = {1664-042X},
  doi       = {10.3389/fphys.2018.00794},
  pages     = {11 Seiten},
  year      = {2018},
  abstract  = {During rapid deceleration of the body, tendons buffer part of the elongation of the muscle-tendon unit (MTU), enabling safe energy dissipation via eccentric muscle contraction. Yet, the influence of changes in tendon stiffness within the physiological range upon these lengthening contractions is unknown. This study aimed to examine the effect of training-induced stiffening of the Achilles tendon on triceps surae muscle-tendon behavior during a landing task. Twenty-one male subjects were assigned to either a 10-week resistance-training program consisting of single-leg isometric plantarflexion (n = 11) or to a non-training control group (n = 10). Before and after the training period, plantarflexion force, peak Achilles tendon strain and stiffness were measured during isometric contractions, using a combination of dynamometry, ultrasound and kinematics data. Additionally, testing included a step-landing task, during which joint mechanics and lengths of gastrocnemius and soleus fascicles, Achilles tendon, and MTU were determined using synchronized ultrasound, kinematics and kinetics data collection. After training, plantarflexion strength and Achilles tendon stiffness increased (15 and 18\%, respectively), and tendon strain during landing remained similar. Likewise, lengthening and negative work produced by the gastrocnemius MTU did not change detectably. However, in the training group, gastrocnemius fascicle length was offset (8\%) to a longer length at touch down and, surprisingly, fascicle lengthening and velocity were reduced by 27 and 21\%, respectively. These changes were not observed for soleus fascicles when accounting for variation in task execution between tests. These results indicate that a training-induced increase in tendon stiffness does not noticeably affect the buffering action of the tendon when the MTU is rapidly stretched. Reductions in gastrocnemius fascicle lengthening and lengthening velocity during landing occurred independently from tendon strain. Future studies are required to provide insight into the mechanisms underpinning these observations and their influence on energy dissipation.},
  language  = {en}
}
@incollection{Finkenberger2018,
  author    = {Finkenberger, Isabel Maria},
  title     = {Die Stadt als st{\"a}dtisch-theatrale Versuchsanordnung: Wie wollen wir in Zukunft leben und welche Stadt brauchen wir daf{\"u}r?},
  series = {Un/Certain Futures - Rollen des Designs in gesellschaftlichen Transformationsprozessen},
  booktitle = {Un/Certain Futures - Rollen des Designs in gesellschaftlichen Transformationsprozessen},
  publisher = {transcript},
  address   = {Bielefeld},
  isbn      = {9783839443323},
  doi       = {https://doi.org/10.1515/9783839443323-009},
  pages     = {86 -- 95},
  year      = {2018},
  language  = {de}
}
@techreport{Drescher2018,
  type      = {Working Paper},
  author    = {Drescher, Hans Paul},
  title     = {The irreversible thermodynamic's theorem of minimum entropy production applied to the laminar and the turbulent Couette flow},
  pages     = {48 Seiten},
  year      = {2018},
  abstract  = {Analyzing thermodynamic non-equilibrium processes, like the laminar and turbulent fluid flow, the dissipation is a key parameter with a characteristic minimum condition. That is applied to characterize laminar and turbulent behaviour of the Couette flow, including its transition in both directions. The Couette flow is chosen as the only flow form with constant shear stress over the flow profile, being laminar, turbulent or both. The local dissipation defines quantitative and stable criteria for the transition and the existence of turbulence. There are basic results: The Navier Stokes equations cannot describe the experimental flow profiles of the turbulent Couette flow. But they are used to quantify the dissipation of turbulent fluctuation. The dissipation minimum requires turbulent structures reaching maximum macroscopic dimensions, describing turbulence as a "non-local" phenomenon. At the transition the Couette flow profiles and the shear stress change by a factor ≅ 5 due to a change of the "apparent" turbulent viscosity by a calculated factor ≅ 27. The resulting difference of the laminar and the turbulent profiles results in two different Reynolds numbers and different loci of transition, which are identified by calculation.},
  language  = {en}
}
@article{HarrisKleefeld2018,
  author    = {Harris, Isaac and Kleefeld, Andreas},
  title     = {The inverse scattering problem for a conductive boundary condition and transmission eigenvalues},
  series = {Applicable Analysis},
  volume    = {99},
  journal   = {Applicable Analysis},
  number    = {3},
  publisher = {Taylor \& Francis},
  address   = {London},
  issn      = {1563-504X},
  doi       = {10.1080/00036811.2018.1504028},
  pages     = {508 -- 529},
  year      = {2018},
  abstract  = {In this paper, we consider the inverse scattering problem associated with an inhomogeneous media with a conductive boundary. In particular, we are interested in two problems that arise from this inverse problem: the inverse conductivity problem and the corresponding interior transmission eigenvalue problem. The inverse conductivity problem is to recover the conductive boundary parameter from the measured scattering data. We prove that the measured scatted data uniquely determine the conductivity parameter as well as describe a direct algorithm to recover the conductivity. The interior transmission eigenvalue problem is an eigenvalue problem associated with the inverse scattering of such materials. We investigate the convergence of the eigenvalues as the conductivity parameter tends to zero as well as prove existence and discreteness for the case of an absorbing media. Lastly, several numerical and analytical results support the theory and we show that the inside-outside duality method can be used to reconstruct the interior conductive eigenvalues.},
  language  = {en}
}
@incollection{Fabo2018,
  author    = {Fabo, Sabine},
  title     = {Einspr{\"u}che gegen den informierten Himmel ; Wegsehen; Distanzschaffen, Spielen},
  series = {Orbitale Irritationen / Herausgeber: REMOTEWORDS: Achim Mohn{\´e} \& Uta Kopp},
  booktitle = {Orbitale Irritationen / Herausgeber: REMOTEWORDS: Achim Mohn{\´e} \& Uta Kopp},
  publisher = {Herbert von Halem Verlag},
  address   = {K{\"o}ln},
  isbn      = {978-3-86962-302-3},
  pages     = {20 -- 45},
  year      = {2018},
  language  = {de}
}
@incollection{Fabo2018,
  author    = {Fabo, Sabine},
  title     = {Eine dekonstruktive Erinnerungsarbeit},
  series = {Doris Frohnapfel, bewaffnete G{\"o}tter = Doris Frohnapfel, armed gods},
  booktitle = {Doris Frohnapfel, bewaffnete G{\"o}tter = Doris Frohnapfel, armed gods},
  publisher = {RpB Richter-Br{\"u}ckner},
  address   = {K{\"o}ln},
  isbn      = {978-3-9817241-2-7},
  pages     = {31 -- 35},
  year      = {2018},
  language  = {de}
}
@techreport{FischedickSchoofHebeletal.2018,
  type      = {Working Paper},
  author    = {Fischedick, Manfred and Schoof, Ren{\´e} and Hebel, Christoph and Merkens, Torsten},
  title     = {Sektorenkopplung als Herausforderung und Chance f{\"u}r das Energieland NRW : Handlungsoptionen und Ergebnispapier der Expertengruppe AG 4 „Sektoren- kopplung" im Netzwerk Netze und Speicher der EnergieAgentur.NRW im Auftrag des Landes Nordrhein-Westfalen / EnergieAgentur.NRW GmbH},
  pages     = {68 Seiten},
  year      = {2018},
  language  = {de}
}
@incollection{Finkenberger2018,
  author    = {Finkenberger, Isabel Maria},
  title     = {Schwellenreiten},
  series = {Prozesse reflexiven Entwerfens : Entwerfen und Forschen in Architektur und Landschaft},
  booktitle = {Prozesse reflexiven Entwerfens : Entwerfen und Forschen in Architektur und Landschaft},
  editor    = {Buchert, Margitta},
  publisher = {JOVIS Verlag},
  address   = {Berlin},
  isbn      = {978-3-86859-558-1},
  pages     = {208 -- 226},
  year      = {2018},
  language  = {de}
}
@book{Kurz2018,
  author    = {Kurz, Melanie},
  title     = {Designstreit : exemplarische Kontroversen {\"u}ber Gestaltung},
  publisher = {Wilhelm Fink},
  address   = {Paderborn},
  isbn      = {978-3-7705-6294-7 (Druckausgabe)},
  pages     = {304 Seiten},
  year      = {2018},
  abstract  = {Die Geschichte des Designs ist ges{\"a}umt von Auseinandersetzungen. Debattiert wird unter Berufsgenossen, in Interessensverb{\"a}nden, zwischen Wettbewerbern und nicht zuletzt an Hochschulen; als Foren dienen zum Beispiel Zeitungen, Konferenzen oder Gerichtss{\"a}le. Doch welche Gr{\"u}nde gibt es f{\"u}r Streit {\"u}ber Design? Die Kontroversen beschr{\"a}nken sich keineswegs auf die {\"A}sthetik von Artefakten. Auch haben wir es trotz der Vielfalt an Streitf{\"a}llen nicht mit einem un{\"u}berschaubaren Feld von zusammenhanglosen Einzelereignissen zu tun. Wie das vorliegende Buch anhand historischer Kontroversen zeigt, lassen sich im Bereich der Gestaltung Streitkategorien identifizieren. Die Diskursanalyse verr{\"a}t, dass sich die Konfliktursachen im Verlauf der Designhistorie kaum ver{\"a}ndern. So haben die angef{\"u}hrten Dispute erstaunliche {\"A}hnlichkeit mit aktuellen Debatten im Fach. Sie sind Lehrst{\"u}cke und k{\"o}nnen dazu anregen, eine Streitkultur im Design zu etablieren, die sich davon distanziert, den Meinungsgegner in ein politisches Lager zu ›verr{\"a}umen‹.},
  language  = {de}
}
@article{Kurz2018,
  author    = {Kurz, Melanie},
  title     = {Was heißt: Verantwortung im Design? Historische Positionen},
  series = {Boxhorn: das Magazin aus dem Fachbereich Gestaltung der FH Aachen},
  journal   = {Boxhorn: das Magazin aus dem Fachbereich Gestaltung der FH Aachen},
  number    = {34},
  address   = {Aachen},
  pages     = {26 -- 33},
  year      = {2018},
  language  = {de}
}