@inproceedings{ButenwegNorda2013,
  author    = {Butenweg, Christoph and Norda, Hannah},
  title     = {Nonlinear analysis of masonry structures according to Eurocode 8},
  series = {Proceedings - Vienna Congress on Recent Advances in Earthquake Engineering and Structural Dynamics 2013 (VEESD 2013)},
  booktitle = {Proceedings - Vienna Congress on Recent Advances in Earthquake Engineering and Structural Dynamics 2013 (VEESD 2013)},
  editor    = {Adam, Christoph and Heuer, Rudolf and Lenhardt, Wolfgang and Schranz, Christian},
  isbn      = {978-3-902749-04-8},
  year      = {2013},
  language  = {en}
}
@article{MelissOesterwindVoss1975,
  author    = {Meliß, Michael and Oesterwind, Dieter and Voß, Alfred},
  title     = {Non-nuclear and non-fossil energy resources and their possibilities for future power generation},
  series = {Kerntechnik},
  volume    = {17},
  journal   = {Kerntechnik},
  number    = {7},
  publisher = {De Gruyter},
  address   = {Berlin},
  issn      = {0932-3902},
  doi       = {10.18419/opus-8093},
  pages     = {301 -- 306},
  year      = {1975},
  abstract  = {It must be stressed that the assessment of the exploitation possibilities of the energy resources discussed in this paper requires further studies. With this proviso, the situation can be provisionally summarised as follows: The total potential of known geothermal steam sources is only 64 GW. Geothermal energy could therefore only make a significant contribution to covering the worldwide power needs if we succeed in exploiting dry geothermal reservoirs. Exploitation of tidal energy is limited to a few geographically favourable locations. The power generation potential at these locations is only about 64 GW. An important drawback of tidal power is discontinuous power generation. Large scale exploitation of wind, wave and glacier energy, and of ocean heat, requires solution of a number of technological problems. The environmental effects of exploitation of these energy resources are to some extent of a qualitatively different nature from those of operation of fossil-fuel-fired and of nuclear power plants. The scanty knowledge in this area often results in these effects being underestimated. In any case, however, it would be deliberately misleading to postulate that any form of power generation is possible without some detrimental effects on the environment. It may be stated in conclusion that, owing to their small potential or to the as yet insufficiently advanced technological development, none of the energy resources discussed in this paper can make a significant contribution to the solution of middle-term energy supply problems, i.e., to a rapid replacement of mineral oil and natural gas.},
  language  = {en}
}
@incollection{Doeren1987,
  author    = {D{\"o}ren, Horst-Peter},
  title     = {Nichtrostende St{\"a}hle},
  series = {Jahrbuch Schweißtechnik. 1988},
  booktitle = {Jahrbuch Schweißtechnik. 1988},
  publisher = {Dt. Verl. f{\"u}r Schweißtechnik (DVS)},
  address   = {D{\"u}sseldorf},
  isbn      = {0935-0292},
  pages     = {188 -- 203},
  year      = {1987},
  language  = {de}
}
@article{ButenwegGellert2013,
  author    = {Butenweg, Christoph and Gellert, Christoph},
  title     = {Nichtlinearer Nachweis von Mauerwerksbauten},
  series = {Mauerwerk : European journal of masonry},
  volume    = {Volume 17},
  journal   = {Mauerwerk : European journal of masonry},
  number    = {Issue 3},
  publisher = {Wiley},
  address   = {Weinheim},
  issn      = {1437-1022 (E-Journal); 1432-3427 (Print)},
  doi       = {10.1002/dama.201300575},
  pages     = {166 -- 171},
  year      = {2013},
  language  = {de}
}
@inproceedings{GellertButenweg2009,
  author    = {Gellert, Christoph and Butenweg, Christoph},
  title     = {Nichtlinearer Erdbebennachweis von Mauerwerksbauten},
  series = {Erdbeben und Mauerwerk : 11. D-A-CH-Tagung 2009 ; [10./11. September 2009 in Z{\"u}rich] / SGEB, Swiss Society for Earthquake Engineering and Structural Dynamics; Schweizerischer Ingenieur- und Architektenverein, Fachgruppe f{\"u}r Br{\"u}ckenbau und Hochbau. [Hrsg. Dazio, Alessandro ...]},
  booktitle = {Erdbeben und Mauerwerk : 11. D-A-CH-Tagung 2009 ; [10./11. September 2009 in Z{\"u}rich] / SGEB, Swiss Society for Earthquake Engineering and Structural Dynamics; Schweizerischer Ingenieur- und Architektenverein, Fachgruppe f{\"u}r Br{\"u}ckenbau und Hochbau. [Hrsg. Dazio, Alessandro ...]},
  publisher = {SIA},
  address   = {Z{\"u}rich},
  organization    = {D-A-C-H Tagung <11, 2009, Z{\"u}rich>},
  isbn      = {978-3-03732-021-1},
  pages     = {125 -- 132},
  year      = {2009},
  language  = {de}
}
@article{ButenwegGellertSchlundt2010,
  author    = {Butenweg, Christoph and Gellert, Christoph and Schlundt, Andreas},
  title     = {Nichtlinearer Erdbebennachweis von Geb{\"a}uden aus Kalksandsteinmauerwerk nach DIN EN 1998},
  series = {Mauerwerk : European journal of masonry},
  volume    = {14},
  journal   = {Mauerwerk : European journal of masonry},
  number    = {3},
  publisher = {Ernst \& Sohn},
  address   = {Berlin},
  issn      = {1432-3427},
  doi       = {10.1002/dama.201000463},
  pages     = {120 -- 125},
  year      = {2010},
  abstract  = {Die Erdbebensicherheit von Geb{\"a}uden aus Kalksandsteinmauerwerk ist aktuell nach DIN 4149 mit linearen Verfahren nachzuweisen. Dies f{\"u}hrt in der praktischen Anwendung zu großen Problemen, da selbst traditionell {\"u}bliche Grundrisse teilweise nicht mehr ohne zus{\"a}tzliche Maßnahmen nachweisbar sind. Zur L{\"o}sung dieser Problematik wurden von der deutschen Mauerwerksindustrie auf nationaler und europ{\"a}ischer Ebene Forschungsprojekte initiiert, deren Ergebnisse in Form von statisch nichtlinearen Verfahren Eingang in den Nationalen Anhang zur DIN EN 1998-1 [12] gefunden haben. Mit den Verfahren wird die Nachweissituation zuk{\"u}nftig grundlegend verbessert, da mit diesen die Tragwerksreserven wesentlich besser ausgenutzt werden k{\"o}nnen. Im Folgenden wird die Anwendung der Verfahren am Beispiel einer Reihenhauszeile aus Kalksandsteinmauerwerk demonstriert. Der Nachweis der Reihenh{\"a}user wurde im Rahmen einer Zustimmung im Einzelfall, die vom Bundesverband Kalksandsteinindustrie eV in Hannover koordiniert wurde, durch unabh{\"a}ngige Gutachter und die Bauaufsicht eingehend gepr{\"u}ft und f{\"u}r richtig befunden. Die Durchf{\"u}hrung des Nachweises erfolgte auf Grundlage eines an der RWTH Aachen entwickelten neuen Nachweiskonzeptes. Die baupraktische Anwendbarkeit und einfache Nachvollziehbarkeit dieses Konzepts ist durch eine softwaretechnische Umsetzung sichergestellt.},
  language  = {de}
}
@inproceedings{LuBeyerBosiljkovetal.2016,
  author    = {Lu, S. and Beyer, K. and Bosiljkov, V. and Butenweg, Christoph and D'Ayala, D. and Degee, H. and Gams, M. and Klouda, J. and Lagomarsino, S. and Penna, A. and Mojsilovic, N. and da Porto, F. and Sorrentino, L. and Vintzileou, E.},
  title     = {Next generation of Eurocode 8, masonry chapter},
  series = {Brick and Block Masonry Proceedings of the 16th International Brick and Block Masonry Conference, Padova, Italy, 26-30 June 2016},
  booktitle = {Brick and Block Masonry Proceedings of the 16th International Brick and Block Masonry Conference, Padova, Italy, 26-30 June 2016},
  editor    = {Modena, Claudio and da Porto, F. and Valluzzi, M.R.},
  publisher = {Taylor \& Francis},
  address   = {London},
  isbn      = {978-1-138-02999-6 (Print)},
  pages     = {695 -- 700},
  year      = {2016},
  abstract  = {This paper describes the procedure on the evaluation of the masonry chapter for the next generation of Eurocode 8, the European Standard for earthquake-resistant design. In CEN, TC 250/SC8, working group WG 1 has been established to support the subcommittee on the topic of masonry on both design of new structures (EN1998-1) and assessment of existing structures (EN1998-3). The aim is to elaborate suggestions for amendments which fit the current state of the art in masonry and earthquake-resistant design. Focus will be on modelling, simplified methods, linear-analysis (q-values, overstrength-values), nonlinear procedures, out-of-plane design as well as on clearer definition of limit states. Beside these, topics related to general material properties, reinforced masonry, confined masonry, mixed structures and non-structural infills will be covered too. This paper presents the preliminary work and results up to the submission date.},
  language  = {en}
}
@article{MottaghySchellschmidtPopovetal.2005,
  author    = {Mottaghy, Darius and Schellschmidt, R. and Popov, Y. A. and Clauser, C. and Kukkonen, I. T. and Nover, G. and Milanovsky, S. and Romushkevich, R. A.},
  title     = {New heat flow data from the immediate vicinity of the Kola super-deep borehole: Vertical variation in heat flow density confirmed and attributed to advection},
  series = {Tectonophysics},
  volume    = {401},
  journal   = {Tectonophysics},
  number    = {1-2},
  issn      = {1879-3266},
  doi       = {10.1016/j.tecto.2005.03.005},
  pages     = {119 -- 142},
  year      = {2005},
  language  = {en}
}
@inproceedings{EdipGarevskiButenwegetal.2014,
  author    = {Edip, Kemal and Garevski, Mihail and Butenweg, Christoph and Sheshov, Vlatko and Bojadjieva, Julijana and Gjorgjiev, Igor},
  title     = {New coupled finite-infinite element approach for wave propagation simulation of unbounded soil media},
  series = {2nd European Conference on Earthquake Engineering and Seismology 2014 (2nd ECEES) : joint event of the 15th European Conference on Earthquake Engineering and the 34th General Assembly of the European Seismological Commission : Istanbul, Turkey, 25-29 August 2014 / European Association for Earthquake Engineering (EAEE) ; Vol. 2},
  booktitle = {2nd European Conference on Earthquake Engineering and Seismology 2014 (2nd ECEES) : joint event of the 15th European Conference on Earthquake Engineering and the 34th General Assembly of the European Seismological Commission : Istanbul, Turkey, 25-29 August 2014 / European Association for Earthquake Engineering (EAEE) ; Vol. 2},
  publisher = {Curran Associates, Inc.},
  address   = {Red Hook, NY},
  organization    = {European Conference on Earthquake Engineering and Seismology <2, 2014, Istanbul>},
  isbn      = {978-1-5108-1021-1},
  pages     = {1556 -- 1561},
  year      = {2014},
  language  = {en}
}
@article{HoylerCizewskiColvin1988,
  author    = {Hoyler, Friedrich and Cizewski, J. A. and Colvin, G. G.},
  title     = {Neutron capture on 193Ir and \&\#963;<\&\#963; SUB>max states in 195Ir / J. A. Cizewski ; G. G. Colvin ... F. Hoyler ...},
  series = {Journal of Physics G. 14 (1988), H. S},
  journal   = {Journal of Physics G. 14 (1988), H. S},
  isbn      = {0305-4616},
  pages     = {S103 -- S108},
  year      = {1988},
  language  = {en}
}
@article{ThielemannStaudtKriegesmann1997,
  author    = {Thielemann, Frank and Staudt, Erich and Kriegesmann, Bernd},
  title     = {Neuformierung von Wertsch{\"o}pfungsketten: Das Beispiel Druckindustrie . Staudt, Erich; Kriegesmann, Bernd; Thielemann, Frank},
  series = {Zeitschrift F{\"u}hrung und Organisation. 96 (1997), H. 2},
  journal   = {Zeitschrift F{\"u}hrung und Organisation. 96 (1997), H. 2},
  isbn      = {0044-3212},
  pages     = {75 -- 80},
  year      = {1997},
  language  = {de}
}
@inproceedings{OetringerDuemmlerGoettsche2020,
  author    = {Oetringer, Kerstin and D{\"u}mmler, Andreas and G{\"o}ttsche, Joachim},
  title     = {Neues Modell zur 1D-Simulation der indirekten Verdunstungsk{\"u}hlung},
  series = {DKV-Tagung 2020, AA II.1},
  booktitle = {DKV-Tagung 2020, AA II.1},
  pages     = {250 -- 262},
  year      = {2020},
  abstract  = {Im Projekt Coolplan- AIR geht es um die Fortentwicklung und Feld- Validierung eines Berechnungs- und Auslegungstools zur energieeffizienten K{\"u}hlung von Geb{\"a}uden mit luftgest{\"u}tzten Systemen. Neben dem Aufbau und der Weiterentwicklung von Simulationsmodellen erfolgen Vermessungen der Gesamtsysteme anhand von Praxisanlagen im Feld. Eine der betrachteten Anlagen arbeitet mit indirekter Verdunstung. Diese Ver{\"o}ffentlichung zeigt den Entwicklungsprozess und den Aufbau des Simulationsmodells zur Verdunstungsk{\"u}hlung in der Simulationsumgebung Matlab- Simulink mit der CARNOT- Toolbox. Das besondere Augenmerk liegt dabei auf dem physikalischen Modell des W{\"a}rme{\"u}bertragers, in dem die Verdunstung implementiert ist. Dem neuen Modellansatz liegt die Annahme einer aus der Enthalpie- Betrachtung hergeleiteten effektiven W{\"a}rmekapazit{\"a}t zugrunde. Des Weiteren wird der Befeuchtungsgrad als konstant angesehen und eine standardisierte Zunahme der W{\"a}rme{\"u}bertragung des feuchten gegen{\"u}ber dem trockenen W{\"a}rme{\"u}bertrager angenommen. Die Validierung des Modells erfolgte anhand von Literaturdaten. F{\"u}r den trockenen W{\"a}rmetauscher ist der maximale absolute Fehler der berechneten Austrittstemperatur (Zuluft) kleiner als ±0.1 K und f{\"u}r den nassen W{\"a}rmetauscher (K{\"u}hlfall) unter der Annahme eines konstanten Verdunstungsgrades kleiner als ±0.4 K.},
  language  = {de}
}
@article{KernBraun2013,
  author    = {Kern, Alexander and Braun, Christian},
  title     = {Neuerungen bei der Blitzschutznorm. Teil 2},
  series = {etz Elektrotechnik und Automation},
  volume    = {Bd. 134},
  journal   = {etz Elektrotechnik und Automation},
  number    = {H. 8},
  publisher = {VDE-Verlag},
  address   = {Wuppertal},
  issn      = {0170-1711},
  pages     = {66 -- 69},
  year      = {2013},
  language  = {de}
}
@article{ButenwegHoltschoppen2012,
  author    = {Butenweg, Christoph and Holtschoppen, Britta},
  title     = {Neuer VCI-Leitfaden f{\"u}r die erdbebensichere Auslegung von Industrieanlagen},
  series = {Bauingenieur : die richtungsweisende Zeitschrift im Bauingenieurswesen ; offizielle Zeitschrift der VDI-Gesellschaft Bautechnik},
  volume    = {Band 87},
  journal   = {Bauingenieur : die richtungsweisende Zeitschrift im Bauingenieurswesen ; offizielle Zeitschrift der VDI-Gesellschaft Bautechnik},
  publisher = {VDI Fachmedien},
  address   = {D{\"u}sseldorf},
  issn      = {1436-4867 (E-Journal); 0005-6650 (Print)},
  pages     = {S18},
  year      = {2012},
  language  = {de}
}
@incollection{MeskourisGellertButenweg2010,
  author    = {Meskouris, Konstantin and Gellert, Christoph and Butenweg, Christoph},
  title     = {Neuer Ansatz f{\"u}r die Bemessung von Mauerwerksbauten},
  series = {Innovationen im konstruktiven Ingenieurbau : Methoden - Materialien - Bauwerke ; Festschrift Professor Hirschfeld / hrsg. von Karl Beucke},
  booktitle = {Innovationen im konstruktiven Ingenieurbau : Methoden - Materialien - Bauwerke ; Festschrift Professor Hirschfeld / hrsg. von Karl Beucke},
  publisher = {Bauhaus-Univ. Weimar},
  address   = {Weimar},
  pages     = {217 -- 224},
  year      = {2010},
  language  = {de}
}
@inproceedings{HellmannsBoehmDilgeretal.2006,
  author    = {Hellmanns, Mark and B{\"o}hm, Stefan and Dilger, Klaus and Welters, T.},
  title     = {Neue M{\"o}glichkeiten der Klebstoffverarbeitung durch geschwindigkeitsproportionalen Handauftrag},
  series = {Adhesive bonding and hybrid bonding in body-in-white shop and assembly : proceedings, 25/26 April 2006, Bad Nauheim/Frankfurt},
  booktitle = {Adhesive bonding and hybrid bonding in body-in-white shop and assembly : proceedings, 25/26 April 2006, Bad Nauheim/Frankfurt},
  publisher = {Technik \& Kommunikation Verl.-GmbH},
  address   = {Berlin},
  pages     = {81},
  year      = {2006},
  language  = {de}
}
@article{Kern2007,
  author    = {Kern, Alexander},
  title     = {Neue deutsche Blitzschutz-Normung. Reihe DIN EN 62305 / VDE 01 85-305-x:2006},
  series = {Der Eisenbahningenieur. 58 (2007), H. 8},
  journal   = {Der Eisenbahningenieur. 58 (2007), H. 8},
  isbn      = {0013-2810},
  pages     = {18 -- 22},
  year      = {2007},
  language  = {de}
}
@book{MeskourisButenweg2005,
  author    = {Meskouris, Konstantin and Butenweg, Christoph},
  title     = {Neubewertung der Erdbebensicherheit von Talsperren in Deutschland : DGEB-Workshop, 28. November 2003 in Potsdam / K. Meskouris, Chr. Butenweg (Hrsg.). (DGEB-Publikation ; Nr. 12)},
  publisher = {DGEB},
  address   = {Aachen},
  isbn      = {3-930108-08-9},
  pages     = {51 S.},
  year      = {2005},
  language  = {de}
}
@article{DielmannMehlkopf2005,
  author    = {Dielmann, Klaus-Peter and Mehlkopf, Marcus},
  title     = {National zugeteilte Emissionen},
  series = {BWK : das Energie-Fachmagazin},
  volume    = {57},
  journal   = {BWK : das Energie-Fachmagazin},
  number    = {5},
  isbn      = {0006-9612},
  issn      = {1618-193X},
  pages     = {48 -- 52},
  year      = {2005},
  language  = {de}
}
@inproceedings{Butenweg2007,
  author    = {Butenweg, Christoph},
  title     = {Nachweis der Erdbebensicherheit von Silos aus Stahl unter Erdbebenbelastung},
  series = {D-A-CH Tagung 2007 : Aktuelle Themen des Erdbebeningenieurwesens und der Baudynamik ; 27. und 28. September 2007, arsenal research, TECHbase Vienna},
  booktitle = {D-A-CH Tagung 2007 : Aktuelle Themen des Erdbebeningenieurwesens und der Baudynamik ; 27. und 28. September 2007, arsenal research, TECHbase Vienna},
  organization    = {D-A-CH Tagung <2007, Wien>},
  pages     = {1 -- 14},
  year      = {2007},
  language  = {de}
}
@article{NordaButenweg2011,
  author    = {Norda, Hannah and Butenweg, Christoph},
  title     = {M{\"o}glichkeiten und Grenzen der Anwendbarkeit statisch nichtlinearer Verfahren nach DIN EN 1998-1},
  series = {Bauingenieur : die richtungsweisende Zeitschrift im Bauingenieurswesen ; offizielle Zeitschrift der VDI-Gesellschaft Bautechnik. Beilage: D-A-CH-Mitteilungsblatt},
  volume    = {Band 86},
  journal   = {Bauingenieur : die richtungsweisende Zeitschrift im Bauingenieurswesen ; offizielle Zeitschrift der VDI-Gesellschaft Bautechnik. Beilage: D-A-CH-Mitteilungsblatt},
  publisher = {VDI Fachmedien},
  address   = {D{\"u}sseldorf},
  issn      = {1436-4867 (E-Journal); 0005-6650 (Print)},
  pages     = {S13 -- S21},
  year      = {2011},
  language  = {de}
}
@article{JungbluthBorchert2008,
  author    = {Jungbluth, Christian and Borchert, J{\"o}rg},
  title     = {M{\"o}glichkeiten der Strompreisbeeinflussung im oligopolistischen Markt},
  series = {ZNER Zeitschrift f{\"u}r Neues Energierecht},
  journal   = {ZNER Zeitschrift f{\"u}r Neues Energierecht},
  number    = {4},
  pages     = {314 -- 323},
  year      = {2008},
  language  = {de}
}
@article{Pieper2011,
  author    = {Pieper, Martin},
  title     = {Multiobjective optimization with expensive objectives applied to a thermodynamic material design problem},
  series = {Proceedings in applied mathematics and mechanics : PAMM. 11 (2011), H. 1},
  journal   = {Proceedings in applied mathematics and mechanics : PAMM. 11 (2011), H. 1},
  publisher = {Wiley},
  address   = {Weinheim},
  isbn      = {1617-7061},
  pages     = {733 -- 734},
  year      = {2011},
  language  = {en}
}
@inproceedings{FeldhusenBrezingPuetzetal.2010,
  author    = {Feldhusen, J{\"o}rg and Brezing, Alexander Nikolaus and P{\"u}tz, Claus and W{\"a}hlisch, Georg},
  title     = {Multi-system CAD-teaching in large classes},
  series = {When design education and design research meet : proceedings of the 12th International Conference on Engineering and Product Design Education, Norwegian University of Science and Technology (NTNU) Trondheim, Norway, 2nd - 3rd September 2010 ; [E\&PDE]},
  booktitle = {When design education and design research meet : proceedings of the 12th International Conference on Engineering and Product Design Education, Norwegian University of Science and Technology (NTNU) Trondheim, Norway, 2nd - 3rd September 2010 ; [E\&PDE]},
  publisher = {Design Society},
  address   = {Glasgow},
  organization    = {International Conference on Engineering and Product Design Education <12, 2010, Trondheim>},
  isbn      = {978-1-904670-19-3},
  pages     = {204 -- 209},
  year      = {2010},
  language  = {en}
}
@article{GoettscheAlexopoulosDuemmleretal.2019,
  author    = {G{\"o}ttsche, Joachim and Alexopoulos, Spiros and D{\"u}mmler, Andreas and Maddineni, S. K.},
  title     = {Multi-Mirror Array Calculations With Optical Error},
  pages     = {1 -- 6},
  year      = {2019},
  abstract  = {The optical performance of a 2-axis solar concentrator was simulated with the COMSOL Multiphysics® software. The concentrator consists of a mirror array, which was created using the application builder. The mirror facets are preconfigured to form a focal point. During tracking all mirrors are moved simultaneously in a coupled mode by 2 motors in two axes, in order to keep the system in focus with the moving sun. Optical errors on each reflecting surface were implemented in combination with the solar angular cone of ± 4.65 mrad. As a result, the intercept factor of solar radiation that is available to the receiver was calculated as a function of the transversal and longitudinal angles of incidence. In addition, the intensity distribution on the receiver plane was calculated as a function of the incidence angles.},
  language  = {en}
}
@inproceedings{RajanKubalskiAltayetal.2017,
  author    = {Rajan, Sreelakshmy and Kubalski, Thomas and Altay, Okyay and Dalguer, Luis A and Butenweg, Christoph},
  title     = {Multi-dimensional fragility analysis of a RC building with components using response surface method},
  series = {24th International Conference on Structural Mechanics in Reactor Technology, Busan, Korea, 20-25 August, 2017},
  booktitle = {24th International Conference on Structural Mechanics in Reactor Technology, Busan, Korea, 20-25 August, 2017},
  publisher = {International Assn for Structural Mechanics in Reactor Technology (IASMiRT)},
  address   = {Raleigh, USA},
  isbn      = {9781510856776},
  pages     = {3126 -- 3135},
  year      = {2017},
  abstract  = {Conventional fragility curves describe the vulnerability of the main structure under external hazards. However, in complex structures such as nuclear power plants, the safety or the risk depends also on the components associated with a system. The classical fault tree analysis gives an overall view of the failure and contains several subsystems to the main event, however, the interactions in the subsystems are not well represented. In order to represent the interaction of the components, a method suggested by Cimellaro et al. (2006) using multidimensional performance limit state functions to obtain the system fragility curves is adopted. This approach gives the possibility of deriving the cumulative fragility taking into account the interaction of the response of different components. In this paper, this approach is used to evaluate seismic risk of a representative electrical building infrastructure, including the component, of a nuclear power plant. A simplified model of the structure, with nonlinear material behavior is employed for the analysis in Abaqus©. The input variables considered are the material parameters, boundary conditions and the seismic input. The variability of the seismic input is obtained from selected ground motion time histories of spectrum compatible synthetic ccelerograms. Unlike the usual Monte Carlo methods used for the probabilistic analysis of the structure, a computationally effective response surface method is used. This method reduces the computational effort of the calculations by reducing the required number of samples.},
  language  = {en}
}
@article{FoersterTillmannGerthsen1995,
  author    = {F{\"o}rster, Arnold and Tillmann, K. and Gerthsen, D.},
  title     = {Morphological transformations of MBE-grown In0.6Ga0.4As island on GaAs(001) substrates / K. Tillmann ; D. Gerthsen ; P. Pfundstein ; A. F{\"o}rster ...},
  series = {Microscopy of semiconducting materials 1995 : proceedings of the Institute of Physics Conference held at Oxford University, 20 - 23 March 1995 / Ed. by A G Cullis ... - (Conference series / Institute of Physics ; 146)},
  journal   = {Microscopy of semiconducting materials 1995 : proceedings of the Institute of Physics Conference held at Oxford University, 20 - 23 March 1995 / Ed. by A G Cullis ... - (Conference series / Institute of Physics ; 146)},
  publisher = {Institute of Physics},
  address   = {Bristol [u.a.]},
  isbn      = {0-7503-0347-6},
  pages     = {195 -- ff.},
  year      = {1995},
  language  = {en}
}
@article{RossiWinandsButenweg2022,
  author    = {Rossi, Leonardo and Winands, Mark H. M. and Butenweg, Christoph},
  title     = {Monte Carlo Tree Search as an intelligent search tool in structural design problems},
  series = {Engineering with Computers : An International Journal for Simulation-Based Engineering},
  volume    = {38},
  journal   = {Engineering with Computers : An International Journal for Simulation-Based Engineering},
  number    = {4},
  editor    = {Zhang, Jessica},
  publisher = {Springer Nature},
  address   = {Cham},
  issn      = {1435-5663},
  doi       = {10.1007/s00366-021-01338-2},
  pages     = {3219 -- 3236},
  year      = {2022},
  abstract  = {Monte Carlo Tree Search (MCTS) is a search technique that in the last decade emerged as a major breakthrough for Artificial Intelligence applications regarding board- and video-games. In 2016, AlphaGo, an MCTS-based software agent, outperformed the human world champion of the board game Go. This game was for long considered almost infeasible for machines, due to its immense search space and the need for a long-term strategy. Since this historical success, MCTS is considered as an effective new approach for many other scientific and technical problems. Interestingly, civil structural engineering, as a discipline, offers many tasks whose solution may benefit from intelligent search and in particular from adopting MCTS as a search tool. In this work, we show how MCTS can be adapted to search for suitable solutions of a structural engineering design problem. The problem consists of choosing the load-bearing elements in a reference reinforced concrete structure, so to achieve a set of specific dynamic characteristics. In the paper, we report the results obtained by applying both a plain and a hybrid version of single-agent MCTS. The hybrid approach consists of an integration of both MCTS and classic Genetic Algorithm (GA), the latter also serving as a term of comparison for the results. The study's outcomes may open new perspectives for the adoption of MCTS as a design tool for civil engineers.},
  language  = {en}
}
@inproceedings{KueppersGroebelKuperjansetal.2011,
  author    = {K{\"u}ppers, Christine and Groebel, Simone and Kuperjans, Isabel and Dielmann, Klaus-Peter},
  title     = {Molekulargenetische Analysen zur Optimierung der Biogasgewinnung},
  series = {Biogas 2011 : 4. Innovationskongress ; Effizienzsteigerung von Biogasanlagen ; Vorstellung der 17 besten Biogas-Innovationen der letzten 12 Monate ; 12. - 13. Mai 2011, im ZUK der Deutschen Bundesstiftung Umwelt ; Tagungsband},
  booktitle = {Biogas 2011 : 4. Innovationskongress ; Effizienzsteigerung von Biogasanlagen ; Vorstellung der 17 besten Biogas-Innovationen der letzten 12 Monate ; 12. - 13. Mai 2011, im ZUK der Deutschen Bundesstiftung Umwelt ; Tagungsband},
  publisher = {Profair Consult+Project},
  address   = {Hildesheim},
  isbn      = {978-3-9813776-1-3},
  pages     = {45 -- 48},
  year      = {2011},
  language  = {de}
}
@article{FoersterZettlerMikkelsenetal.1992,
  author    = {F{\"o}rster, Arnold and Zettler, J.-T. and Mikkelsen, H. and Leo, K.},
  title     = {Modulated ellipsometric measurements and transfer-matrix calculation of the field-dependent dielectric function of a multiple quantum well / J.-Th. Zettler ; H. Mikkelsen ; K. Leo ... A. F{\"o}rster},
  series = {Physical Review B . 46 (1992), H. 24},
  journal   = {Physical Review B . 46 (1992), H. 24},
  isbn      = {0163-1829},
  pages     = {15955 -- 15962},
  year      = {1992},
  language  = {en}
}
@inproceedings{KalkerNeumannButenwegetal.2005,
  author    = {Kalker, Ines and Neumann, M. and Butenweg, Christoph and Holler, Stefan},
  title     = {Modelling of textile strengthened masonry},
  series = {Proceedings of the Tenth International Conference on Civil, Structural and Environmental Engineering Computing : [Rome, Italy, 30. August - 2. September 2005] / ed. by B. H. V. Topping},
  booktitle = {Proceedings of the Tenth International Conference on Civil, Structural and Environmental Engineering Computing : [Rome, Italy, 30. August - 2. September 2005] / ed. by B. H. V. Topping},
  publisher = {Civil-Comp Press},
  address   = {Stirling},
  organization    = {International Conference on Civil, Structural and Environmental Engineering Computing <10, 2005, Rome>},
  isbn      = {1-905088-00-0},
  doi       = {10.4203/ccp.81.184},
  pages     = {447 -- 448},
  year      = {2005},
  language  = {en}
}
@article{MistlerButenwegMeskouris2006,
  author    = {Mistler, Michael and Butenweg, Christoph and Meskouris, Konstantin},
  title     = {Modelling methods of historic masonry buildings under seismic excitation},
  series = {Journal of seismology},
  volume    = {Volume 10},
  journal   = {Journal of seismology},
  number    = {No. 4},
  issn      = {1383-4649 (Print) ; 1573-157X (E-Journal)},
  doi       = {10.1007/s10950-006-9033-z},
  pages     = {497 -- 510},
  year      = {2006},
  language  = {en}
}
@inproceedings{MertensBraunerBaieretal.2022,
  author    = {Mertens, Alexander and Brauner, Philipp and Baier, Ralph and Brillowski, Florian and Dammers, Hannah and van Dyck, Marc and Kong, Iris and K{\"o}nigs, Peter and Kordtomeikel, Frauke and Liehner, Gian Luca and P{\"u}tz, Sebastian and Rodermann, Niklas and Schaar, Anne Kathrin and Steuer-Dankert, Linda and Vervier, Luisa and Wlecke, Shari and Gries, Thomas and Leicht-Scholten, Carmen and Nagel, Saskia K. and Piller, Frank T. and Schuh, G{\"u}nther and Ziefle, Martina and Nitsch, Verena},
  title     = {Modelling Human Factors in Cyber Physical Production Systems by the Integration of Human Digital Shadows},
  series = {Modellierung 2022 Satellite Events},
  booktitle = {Modellierung 2022 Satellite Events},
  editor    = {Michael, Judith and Pfeiffer, J{\´e}r{\^o}me and Wortmann, Andreas},
  publisher = {GI Gesellschaft f{\"u}r Informatik},
  address   = {Bonn},
  doi       = {10.18420/modellierung2022ws-018},
  pages     = {147 -- 149},
  year      = {2022},
  abstract  = {The future of industrial manufacturing and production will increasingly manifest in the form of cyber-physical production systems. Here, Digital Shadows will act as mediators between the physical and digital world to model and operationalize the interactions and relationships between different entities in production systems. Until now, the associated concepts have been primarily pursued and implemented from a technocentric perspective, in which human actors play a subordinate role, if they are considered at all. This paper outlines an anthropocentric approach that explicitly considers the characteristics, behavior, and traits and states of human actors in socio-technical production systems. For this purpose, we discuss the potentials and the expected challenges and threats of creating and using Human Digital Shadows in production.},
  language  = {en}
}
@article{KubalskiButenweg2015,
  author    = {Kubalski, Thomas and Butenweg, Christoph},
  title     = {Modelling strategies for horizontally loaded infill masonry},
  series = {Mauerwerk : European journal of masonry},
  volume    = {Volume 19},
  journal   = {Mauerwerk : European journal of masonry},
  number    = {Issue 5},
  publisher = {Wiley},
  address   = {Weinheim},
  doi       = {10.1002/dama.201500675},
  pages     = {363 -- 369},
  year      = {2015},
  language  = {de}
}
@inproceedings{RosinKubalskiButenweg2013,
  author    = {Rosin, Julia and Kubalski, Thomas and Butenweg, Christoph},
  title     = {Modellierung eines basisisolierten, zylindrischen Fl{\"u}ssigkeitstanks aus Stahl},
  series = {13. D-A-CH Tagung f{\"u}r Erdbebeningenieurwesen und Baudynamik (D-A-CH 2013) : 29.-30. August 2013, Wien, {\"O}sterreich},
  booktitle = {13. D-A-CH Tagung f{\"u}r Erdbebeningenieurwesen und Baudynamik (D-A-CH 2013) : 29.-30. August 2013, Wien, {\"O}sterreich},
  organization    = {D-A-CH Tagung f{\"u}r Erdbebeningenieurwesen und Baudynamik <13, 2013, Wien>},
  pages     = {1 -- 10},
  year      = {2013},
  language  = {de}
}
@book{MeissenHotfilter1972,
  author    = {Meißen, Ralf and Hotfilter, Josef},
  title     = {Modell einer Einrichtung zur Positionierung von kugelf{\"o}rmigen Brennelementen nach einer Bohrung mit ber{\"u}hrungsloser fluidischer Abtastung / Josef Hotfilter ; Ralf Meißen},
  publisher = {Kernforschungsanlage},
  address   = {J{\"u}lich},
  pages     = {17 Bl.: graph. Darst.},
  year      = {1972},
  language  = {de}
}
@inproceedings{ZahraPhaniSrujanChicoCaminosetal.2022,
  author    = {Zahra, Mahdi and Phani Srujan, Merige and Chico Caminos, Ricardo Alexander and Schmitz, Pascal and Herrmann, Ulf and Teixeira Boura, Cristiano Jos{\´e} and Schmitz, Mark and Gielen, Hans and Gedle, Yibekal and Dersch, J{\"u}rgen},
  title     = {Modeling the thermal behavior of solar salt in electrical resistance heaters for the application in PV-CSP hybrid power plants},
  series = {SOLARPACES 2020},
  booktitle = {SOLARPACES 2020},
  number    = {2445 / 1},
  publisher = {AIP conference proceedings / American Institute of Physics},
  address   = {Melville, NY},
  isbn      = {978-0-7354-4195-8},
  issn      = {1551-7616 (online)},
  doi       = {10.1063/5.0086268},
  pages     = {9 Seiten},
  year      = {2022},
  abstract  = {Concentrated Solar Power (CSP) systems are able to store energy cost-effectively in their integrated thermal energy storage (TES). By intelligently combining Photovoltaics (PV) systems with CSP, a further cost reduction of solar power plants is expected, as well as an increase in dispatchability and flexibility of power generation. PV-powered Resistance Heaters (RH) can be deployed to raise the temperature of the molten salt hot storage from 385 °C up to 565 °C in a Parabolic Trough Collector (PTC) plant. To avoid freezing and decomposition of molten salt, the temperature distribution in the electrical resistance heater is investigated in the present study. For this purpose, a RH has been modeled and CFD simulations have been performed. The simulation results show that the hottest regions occur on the electric rod surface behind the last baffle. A technical optimization was performed by adjusting three parameters: Shell-baffle clearance, electric rod-baffle clearance and number of baffles. After the technical optimization was carried out, the temperature difference between the maximum temperature and the average outlet temperature of the salt is within the acceptable limits, thus critical salt decomposition has been avoided. Additionally, the CFD simulations results were analyzed and compared with results obtained with a one-dimensional model in Modelica.},
  language  = {en}
}
@article{VogtIwanowskiStrahserMarquartetal.2013,
  author    = {Vogt, Christian and Iwanowski-Strahser, Katha and Marquart, Gabriele and Arnold, Juliane and Mottaghy, Darius and Pechnig, Renate and Gnjezda, Daniel and Clauser, Christoph},
  title     = {Modeling contribution to risk assessment of thermal production power for geothermal reservoirs},
  series = {Renewable Energy},
  volume    = {53},
  journal   = {Renewable Energy},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0960-1481},
  doi       = {10.1016/j.renene.2012.11.026},
  pages     = {230 -- 241},
  year      = {2013},
  language  = {en}
}
@inproceedings{RendonSchwagerGhiasietal.2020,
  author    = {Rendon, Carlos and Schwager, Christian and Ghiasi, Mona and Schmitz, Pascal and Bohang, Fakhri and Chico Caminos, Ricardo Alexander and Teixeira Boura, Cristiano Jos{\´e} and Herrmann, Ulf},
  title     = {Modeling and upscaling of a pilot bayonettube reactor for indirect solar mixed methane reforming},
  series = {AIP Conference Proceedings},
  booktitle = {AIP Conference Proceedings},
  number    = {2303},
  doi       = {10.1063/5.0029974},
  pages     = {170012-1 -- 170012-9},
  year      = {2020},
  abstract  = {A 16.77 kW thermal power bayonet-tube reactor for the mixed reforming of methane using solar energy has been designed and modeled. A test bench for the experimental tests has been installed at the Synlight facility in Juelich, Germany and has just been commissioned. This paper presents the solar-heated reactor design for a combined steam and dry reforming as well as a scaled-up process simulation of a solar reforming plant for methanol production. Solar power towers are capable of providing large amounts of heat to drive high-endothermic reactions, and their integration with thermochemical processes shows a promising future. In the designed bayonet-tube reactor, the conventional burner arrangement for the combustion of natural gas has been substituted by a continuous 930 °C hot air stream, provided by means of a solar heated air receiver, a ceramic thermal storage and an auxiliary firing system. Inside the solar-heated reactor, the heat is transferred by means of convective mechanism mainly; instead of radiation mechanism as typically prevailing in fossil-based industrial reforming processes. A scaled-up solar reforming plant of 50.5 MWth was designed and simulated in Dymola® and AspenPlus®. In comparison to a fossil-based industrial reforming process of the same thermal capacity, a solar reforming plant with thermal storage promises a reduction up to 57 \% of annual natural gas consumption in regions with annual DNI-value of 2349 kWh/m2. The benchmark solar reforming plant contributes to a CO2 avoidance of approx. 79 kilotons per year. This facility can produce a nominal output of 734.4 t of synthesis gas and out of this 530 t of methanol a day.},
  language  = {en}
}
@article{RiekeStollenwerkDahmenetal.2018,
  author    = {Rieke, Christian and Stollenwerk, Dominik and Dahmen, Markus and Pieper, Martin},
  title     = {Modeling and optimization of a biogas plant for a demand-driven energy supply},
  series = {Energy},
  volume    = {145},
  journal   = {Energy},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0360-5442},
  doi       = {10.1016/j.energy.2017.12.073},
  pages     = {657 -- 664},
  year      = {2018},
  abstract  = {Due to the Renewable Energy Act, in Germany it is planned to increase the amount of renewable energy carriers up to 60\%. One of the main problems is the fluctuating supply of wind and solar energy. Here biogas plants provide a solution, because a demand-driven supply is possible. Before running such a plant, it is necessary to simulate and optimize the process. This paper provides a new model of a biogas plant, which is as accurate as the standard ADM1 model. The advantage compared to ADM1 is that it is based on only four parameters compared to 28. Applying this model, an optimization was installed, which allows a demand-driven supply by biogas plants. Finally the results are confirmed by several experiments and measurements with a real test plant.},
  language  = {en}
}
@inproceedings{SchwagerAngeleSchwarzboezletal.2023,
  author    = {Schwager, Christian and Angele, Florian and Schwarzb{\"o}zl, Peter and Teixeira Boura, Cristiano Jos{\´e} and Herrmann, Ulf},
  title     = {Model predictive assistance for operational decision making in molten salt receiver systems},
  series = {SolarPACES: Solar Power \& Chemical Energy Systems},
  booktitle = {SolarPACES: Solar Power \& Chemical Energy Systems},
  number    = {2815 / 1},
  publisher = {AIP conference proceedings / American Institute of Physics},
  address   = {Melville, NY},
  isbn      = {978-0-7354-4623-6},
  issn      = {1551-7616 (online)},
  doi       = {10.1063/5.0151514},
  pages     = {8 Seiten},
  year      = {2023},
  abstract  = {Despite the challenges of pioneering molten salt towers (MST), it remains the leading technology in central receiver power plants today, thanks to cost effective storage integration and high cost reduction potential. The limited controllability in volatile solar conditions can cause significant losses, which are difficult to estimate without comprehensive modeling [1]. This paper presents a Methodology to generate predictions of the dynamic behavior of the receiver system as part of an operating assistance system (OAS). Based on this, it delivers proposals if and when to drain and refill the receiver during a cloudy period in order maximize the net yield and quantifies the amount of net electricity gained by this. After prior analysis with a detailed dynamic two-phase model of the entire receiver system, two different reduced modeling approaches where developed and implemented in the OAS. A tailored decision algorithm utilizes both models to deliver the desired predictions efficiently and with appropriate accuracy.},
  language  = {en}
}
@article{FoersterZamdmerHuetal.1999,
  author    = {F{\"o}rster, Arnold and Zamdmer, N. and Hu, Qing and Verghese, S.},
  title     = {Mode-Discriminating Photoconductor and Coplanar Wave-Guide Circuits for Picosecond Sampling. Zamdmer, N.; Hu, Qing ; Verghese, S. ; F{\"o}rster, A.},
  series = {Applied Physics Letters. 74 (1999), H. 7},
  journal   = {Applied Physics Letters. 74 (1999), H. 7},
  isbn      = {1077-3118},
  pages     = {1039 -- 1041},
  year      = {1999},
  language  = {en}
}
@article{ThielemannKriegesmannSchaffner1995,
  author    = {Thielemann, Frank and Kriegesmann, Bernd and Schaffner, M.},
  title     = {Mit vereinten Kr{\"a}ften die Wettbewerbsf{\"a}higkeit steigern - Kooperation als Antwort auf den In­novationsdruck . Kriegesmann, B.; Thielemann, F.; Schaffner, M.},
  series = {Der Druckspiegel. 50 (1995), H. 10},
  journal   = {Der Druckspiegel. 50 (1995), H. 10},
  isbn      = {0012-6500},
  pages     = {931 -- 935},
  year      = {1995},
  language  = {de}
}
@article{Thielemann1998,
  author    = {Thielemann, Frank},
  title     = {Mit vereinten Kr{\"a}ften},
  series = {Trockenbau, Akustik : Magazin f{\"u}r Planung und Ausf{\"u}hrung. 15 (1998), H. 5},
  journal   = {Trockenbau, Akustik : Magazin f{\"u}r Planung und Ausf{\"u}hrung. 15 (1998), H. 5},
  isbn      = {0179-8006},
  pages     = {60 -- 68},
  year      = {1998},
  language  = {de}
}
@article{Thielemann1998,
  author    = {Thielemann, Frank},
  title     = {Mit strategischen Allianzen ins n{\"a}chste Jahrtausend},
  series = {Druckspiegel. 53 (1998), H. 5},
  journal   = {Druckspiegel. 53 (1998), H. 5},
  isbn      = {0012-6500},
  pages     = {21 -- 24},
  year      = {1998},
  language  = {de}
}
@article{DielmannIhle2000,
  author    = {Dielmann, Klaus-Peter and Ihle, R.},
  title     = {Mikroturbinen : neue Chancen der Kraft-W{\"a}rme-(K{\"a}lte-)Kopplung im Leistungsbereich 30 - 200 kW(ind el) / R. Ihle ; K. Dielmann},
  series = {Integrierte Energiesysteme : Chancen im Wettbewerb ; Tagung N{\"u}rnberg, 4. und 5. April 2000 / VDI-Gesellschaft Energietechnik. - (VDI-Berichte ; 1539)},
  journal   = {Integrierte Energiesysteme : Chancen im Wettbewerb ; Tagung N{\"u}rnberg, 4. und 5. April 2000 / VDI-Gesellschaft Energietechnik. - (VDI-Berichte ; 1539)},
  publisher = {VDI-Verl.},
  address   = {D{\"u}sseldorf},
  isbn      = {3-18-091539-0},
  pages     = {245 -- 266},
  year      = {2000},
  language  = {de}
}
@article{Dielmann2001,
  author    = {Dielmann, Klaus-Peter},
  title     = {Mikrogasturbinen : Technik und Anwendung},
  series = {BWK : das Energie-Fachmagazin . 53 (2001), H. 6},
  journal   = {BWK : das Energie-Fachmagazin . 53 (2001), H. 6},
  isbn      = {0006-9612},
  pages     = {6 -- 9},
  year      = {2001},
  language  = {de}
}
@incollection{BouvyKuperjans2004,
  author    = {Bouvy, C. and Kuperjans, Isabel},
  title     = {Mikro-Gasturbinen : eine neue Technologie zur Kraft-W{\"a}rme-Kopplung in kleinen und mittleren Unternehmen},
  series = {Entwicklungslinien der Energietechnik 2004},
  booktitle = {Entwicklungslinien der Energietechnik 2004},
  edition   = {CD-ROM-Ausg.},
  publisher = {VDI-Verlag},
  address   = {D{\"u}sseldorf},
  year      = {2004},
  language  = {de}
}
@article{DielmannSchieke2000,
  author    = {Dielmann, Klaus-Peter and Schieke, W.},
  title     = {Mikro-Gasturbinen : Aufbau und Anwendung},
  series = {Gasturbinen f{\"u}r kombinierte Gas-Dampfturbinenanlagen : und Workshop Advanced Power Plant Processes for Solid Fuels Focussing on Combined Cycles ; Tagung Essen, 13. und 14. September 2000 / VDI-Gesellschaft Energietechnik. - (VDI-Berichte ; 1566)},
  journal   = {Gasturbinen f{\"u}r kombinierte Gas-Dampfturbinenanlagen : und Workshop Advanced Power Plant Processes for Solid Fuels Focussing on Combined Cycles ; Tagung Essen, 13. und 14. September 2000 / VDI-Gesellschaft Energietechnik. - (VDI-Berichte ; 1566)},
  publisher = {VDI-Verl.},
  address   = {D{\"u}sseldorf},
  isbn      = {3-18-091566-8},
  pages     = {187 -- 210},
  year      = {2000},
  language  = {de}
}
@article{Dielmann2000,
  author    = {Dielmann, Klaus-Peter},
  title     = {Mikro-Gasturbine als Kleinst-BHKW-Bericht {\"u}ber Einsatzerfahrungen},
  series = {F{\"u}nftes VWEW-Fachforum Nahw{\"a}rme 2000 : W{\"a}rmedirekt-Service der Energiedienstleistungsunternehmen mit Fachausstellung Nahw{\"a}rmetechnik 2000 ; 4. und 5. Mai 2000 in Halle},
  journal   = {F{\"u}nftes VWEW-Fachforum Nahw{\"a}rme 2000 : W{\"a}rmedirekt-Service der Energiedienstleistungsunternehmen mit Fachausstellung Nahw{\"a}rmetechnik 2000 ; 4. und 5. Mai 2000 in Halle},
  publisher = {VWEW},
  address   = {[Frankfurt, Main]},
  pages     = {5.1 -- 5.22},
  year      = {2000},
  language  = {de}
}