@article{ZhenLiangStaatetal.2024,
  author    = {Zhen, Manghao and Liang, Yunpei and Staat, Manfred and Li, Quanqui and Li, Jianbo},
  title     = {Discontinuous fracture behaviors and constitutive model of sandstone specimens containing non-parallel prefabricated fissures under uniaxial compression},
  series = {Theoretical and Applied Fracture Mechanics},
  volume    = {131},
  journal   = {Theoretical and Applied Fracture Mechanics},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0167-8442},
  doi       = {10.1016/j.tafmec.2024.104373},
  pages     = {Artikel 104373},
  year      = {2024},
  abstract  = {The deformation and damage laws of non-homogeneous irregular structural planes in rocks are the basis for studying the stability of rock engineering. To investigate the damage characteristics of rock containing non-parallel fissures, uniaxial compression tests and numerical simulations were conducted on sandstone specimens containing three non-parallel fissures inclined at 0°, 45° and 90° in this study. The characteristics of crack initiation and crack evolution of fissures with different inclinations were analyzed. A constitutive model for the discontinuous fractures of fissured sandstone was proposed. The results show that the fracture behaviors of fissured sandstone specimens are discontinuous. The stress-strain curves are non-smooth and can be divided into nonlinear crack closure stage, linear elastic stage, plastic stage and brittle failure stage, of which the plastic stage contains discontinuous stress drops. During the uniaxial compression test, the middle or ends of 0° fissures were the first to crack compared to 45° and 90° fissures. The end with small distance between 0° and 45° fissures cracked first, and the end with large distance cracked later. After the final failure, 0° fissures in all specimens were fractured, while 45° and 90° fissures were not necessarily fractured. Numerical simulation results show that the concentration of compressive stress at the tips of 0°, 45° and 90° fissures, as well as the concentration of tensile stress on both sides, decreased with the increase of the inclination angle. A constitutive model for the discontinuous fractures of fissured sandstone specimens was derived by combining the logistic model and damage mechanic theory. This model can well describe the discontinuous drops of stress and agrees well with the whole processes of the stress-strain curves of the fissured sandstone specimens.},
  language  = {en}
}
@article{TranStaat2021,
  author    = {Tran, Ngoc Trinh and Staat, Manfred},
  title     = {Direct plastic structural design under random strength and random load by chance constrained programming},
  series = {European Journal of Mechanics - A/Solids},
  volume    = {85},
  journal   = {European Journal of Mechanics - A/Solids},
  number    = {Article 104106},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0997-7538},
  doi       = {10.1016/j.euromechsol.2020.104106},
  year      = {2021},
  language  = {en}
}
@article{TranStaat2020,
  author    = {Tran, Ngoc Trinh and Staat, Manfred},
  title     = {Direct plastic structural design under lognormally distributed strength by chance constrained programming},
  series = {Optimization and Engineering},
  volume    = {21},
  journal   = {Optimization and Engineering},
  number    = {1},
  publisher = {Springer Nature},
  address   = {Cham},
  issn      = {1573-2924},
  doi       = {10.1007/s11081-019-09437-2},
  pages     = {131 -- 157},
  year      = {2020},
  abstract  = {We propose the so-called chance constrained programming model of stochastic programming theory to analyze limit and shakedown loads of structures under random strength with a lognormal distribution. A dual chance constrained programming algorithm is developed to calculate simultaneously both the upper and lower bounds of the plastic collapse limit and the shakedown limit. The edge-based smoothed finite element method (ES-FEM) is used with three-node linear triangular elements.},
  language  = {en}
}
@inproceedings{TranMatthiesStavroulakisetal.2018,
  author    = {Tran, Ngoc Trinh and Matthies, Hermann G. and Stavroulakis, Georgios Eleftherios and Staat, Manfred},
  title     = {Direct plastic structural design by chance constrained programming},
  series = {6th European Conference on Computational Mechanics (ECCM 6), 7th European Conference on Computational Fluid Dynamics (ECFD 7), 11-15 June 2018, Glasgow, UK},
  booktitle = {6th European Conference on Computational Mechanics (ECCM 6), 7th European Conference on Computational Fluid Dynamics (ECFD 7), 11-15 June 2018, Glasgow, UK},
  pages     = {12 Seiten},
  year      = {2018},
  abstract  = {We propose a stochastic programming method to analyse limit and shakedown of structures under random strength with lognormal distribution. In this investigation a dual chance constrained programming algorithm is developed to calculate simultaneously both the upper and lower bounds of the plastic collapse limit or the shakedown limit. The edge-based smoothed finite element method (ES-FEM) using three-node linear triangular elements is used.},
  language  = {en}
}
@article{StaatHeitzerLangetal.2005,
  author    = {Staat, Manfred and Heitzer, M. and Lang, H. and Wirtz, K.},
  title     = {Direct Finite Element Route for Design-by-Analysis of Pressure Components},
  series = {International Journal of Pressure Vessels and Piping. 82 (2005), H. 1},
  journal   = {International Journal of Pressure Vessels and Piping. 82 (2005), H. 1},
  isbn      = {0308-0161},
  pages     = {61 -- 67},
  year      = {2005},
  language  = {en}
}
@article{Staat2005,
  author    = {Staat, Manfred},
  title     = {Direct finite element route for design-by-analysis of pressure components},
  year      = {2005},
  abstract  = {In the new European standard for unfired pressure vessels, EN 13445-3, there are two approaches for carrying out a Design-by-Analysis that cover both the stress categorization method (Annex C) and the direct route method (Annex B) for a check against global plastic deformation and against progressive plastic deformation. This paper presents the direct route in the language of limit and shakedown analysis. This approach leads to an optimization problem. Its solution with Finite Element Analysis is demonstrated for mechanical and thermal actions. One observation from the examples is that the so-called 3f (3Sm) criterion fails to be a reliable check against progressive plastic deformation. Precise conditions are given, which greatly restrict the applicability of the 3f criterion.},
  subject      = {Einspielen <Werkstoff>},
  language  = {en}
}
@inproceedings{HunkerJungGossmannetal.2019,
  author    = {Hunker, Jan and Jung, Alexander and Goßmann, Matthias and Linder, Peter and Staat, Manfred},
  title     = {Development of a tool to analyze the conduction speed in microelectrode array measurements of cardiac tissue},
  series = {3rd YRA MedTech Symposium 2019 : May 24 / 2019 / FH Aachen},
  booktitle = {3rd YRA MedTech Symposium 2019 : May 24 / 2019 / FH Aachen},
  editor    = {Staat, Manfred and Erni, Daniel},
  publisher = {Universit{\"a}t Duisburg-Essen},
  address   = {Duisburg},
  organization    = {MedTech Symposium},
  isbn      = {978-3-940402-22-6},
  doi       = {10.17185/duepublico/48750},
  pages     = {7 -- 8},
  year      = {2019},
  abstract  = {The discovery of human induced pluripotent stem cells reprogrammed from somatic cells [1] and their ability to differentiate into cardiomyocytes (hiPSC-CMs) has provided a robust platform for drug screening [2]. Drug screenings are essential in the development of new components, particularly for evaluating the potential of drugs to induce life-threatening pro-arrhythmias. Between 1988 and 2009, 14 drugs have been removed from the market for this reason [3]. The microelectrode array (MEA) technique is a robust tool for drug screening as it detects the field potentials (FPs) for the entire cell culture. Furthermore, the propagation of the field potential can be examined on an electrode basis. To analyze MEA measurements in detail, we have developed an open-source tool.},
  language  = {en}
}
@article{HasanKeilStaatetal.2012,
  author    = {Hasan, Istabrak and Keil, Ludger and Staat, Manfred and Wahl, Gerhard and Bourauel, Christoph},
  title     = {Determination of the frictional coefficient of the implant-antler interface : experimental approach},
  series = {Biomedical Engineering / Biomedizinische Technik},
  volume    = {57},
  journal   = {Biomedical Engineering / Biomedizinische Technik},
  number    = {5},
  publisher = {De Gruyter},
  address   = {Berlin},
  issn      = {1862-278X},
  pages     = {359 -- 363},
  year      = {2012},
  abstract  = {The similar bone structure of reindeer antler to human bone permits studying the osseointegration of dental implants in the jawbone. As the friction is one of the major factors that have a significant influence on the initial stability of immediately loaded dental implants, it is essential to define the frictional coefficient of the implant-antler interface. In this study, the kinetic frictional forces at the implant-antler interface were measured experimentally using an optomechanical setup and a stepping motor controller under different axial loads and sliding velocities. The corresponding mean values of the static and kinetic frictional coefficients were within the range of 0.5-0.7 and 0.3-0.5, respectively. An increase in the frictional forces with increasing applied axial loads was registered. The measurements showed an evidence of a decrease in the magnitude of the frictional coefficient with increasing sliding velocity. The results of this study provide a considerable assessment to clarify the suitable frictional coefficient to be used in the finite element contact analysis of antler specimens.},
  language  = {en}
}
@article{StaatSchwartzLangetal.2003,
  author    = {Staat, Manfred and Schwartz, M. and Lang, H. and Wirtz, K. and Heitzer, M.},
  title     = {Design by Analysis of Pressure Components by non-linear Optimization},
  series = {The 10th International Conference on Pressure Vessel Technology, July 7-10, 2003, Vienna, Austria, Proceedings ICPVT-10 / Zeman, J. L. [ed]},
  journal   = {The 10th International Conference on Pressure Vessel Technology, July 7-10, 2003, Vienna, Austria, Proceedings ICPVT-10 / Zeman, J. L. [ed]},
  publisher = {{\"O}GS, {\"O}sterreichische Gesellschaft f{\"u}r Schweißtechnik},
  address   = {Wien},
  isbn      = {3950152814},
  pages     = {59 -- 65},
  year      = {2003},
  language  = {en}
}
@inproceedings{Staat2003,
  author    = {Staat, Manfred},
  title     = {Design by Analysis of Pressure Components by non-linear Optimization},
  year      = {2003},
  abstract  = {This paper presents the direct route to Design by Analysis (DBA) of the new European pressure vessel standard in the language of limit and shakedown analysis (LISA). This approach leads to an optimization problem. Its solution with Finite Element Analysis is demonstrated for some examples from the DBA-Manual. One observation from the examples is, that the optimisation approach gives reliable and close lower bound solutions leading to simple and optimised design decision.},
  language  = {en}
}
@article{DefosseKleinschmidtSchmutzetal.2022,
  author    = {Defosse, Jerome and Kleinschmidt, Joris and Schmutz, Axel and Loop, Torsten and Staat, Manfred and Gatzweiler, Karl-Heinz and Wappler, Frank and Schieren, Mark},
  title     = {Dental strain on maxillary incisors during tracheal intubation with double-lumen tubes and different laryngoscopy techniques - a blinded manikin study},
  series = {Journal of Cardiothoracic and Vascular Anesthesia},
  volume    = {36},
  journal   = {Journal of Cardiothoracic and Vascular Anesthesia},
  number    = {8, Part B},
  publisher = {Elsevier},
  address   = {New York, NY},
  issn      = {1053-0770},
  doi       = {10.1053/j.jvca.2022.02.017},
  pages     = {3021 -- 3027},
  year      = {2022},
  language  = {en}
}
@misc{TopcuMadabhushiStaat2022,
  author    = {Topcu, Murat and Madabhushi, Gopal Santana Phani and Staat, Manfred},
  title     = {Datasets from FEM Simulations done with COMSOL Multiphysics and Code_Aster},
  doi       = {10.6084/m9.figshare.19333295.v2},
  year      = {2022},
  abstract  = {Datasets from FEM Simulations done with COMSOL Multiphysics and Code_Aster for an elastic stress transfer between matrix and fibres having a variable radius.},
  language  = {en}
}
@misc{JungMuellerStaat2021,
  author    = {Jung, Alexander and M{\"u}ller, Wolfram and Staat, Manfred},
  title     = {Corrigendum to "Wind and fairness in ski jumping: A computer modelling analysis" [J. Biomech. 75 (2018) 147-153]},
  series = {Journal of Biomechanics},
  volume    = {128},
  journal   = {Journal of Biomechanics},
  number    = {Article number: 110690},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0021-9290},
  doi       = {10.1016/j.jbiomech.2021.110690},
  pages     = {1 Seite},
  year      = {2021},
  language  = {en}
}
@article{JungStaatMueller2018,
  author    = {Jung, Alexander and Staat, Manfred and M{\"u}ller, Wolfram},
  title     = {Corrigendum to "Flight style optimization in ski jumping on normal, large, and ski flying hills" [J. Biomech 47 (2014) 716-722]},
  series = {Journals of Biomechanics},
  journal   = {Journals of Biomechanics},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0021-9290},
  doi       = {10.1016/j.jbiomech.2018.02.001},
  pages     = {313},
  year      = {2018},
  language  = {en}
}
@misc{StaatBarry2006,
  author    = {Staat, Manfred and Barry, Steve},
  title     = {Continuum Mechanics with an Introduction to the Finite Element Method / Steve Barry; Manfred Staat. With extensions by Manfred Staat.},
  year      = {2006},
  abstract  = {Contents: 1 Introduction 2 One Dimensional Continuum Mechanics 3 Tensors 4 Three Dimensional Stress and Strain 5 Conservation Laws 6 Contiunuum Modelling 7 Plain Problems 8 Questions 9 Reference Information},
  subject      = {Technische Mechanik},
  language  = {en}
}
@inproceedings{JungStaat2016,
  author    = {Jung, Alexander and Staat, Manfred},
  title     = {Computing olympic gold: Ski jumping as an example},
  series = {1st YRA MedTech Symposium 2016 : April 8th / 2016 / University of Duisburg-Essen},
  booktitle = {1st YRA MedTech Symposium 2016 : April 8th / 2016 / University of Duisburg-Essen},
  editor    = {Erni, Daniel},
  publisher = {Universit{\"a}t Duisburg-Essen},
  address   = {Duisburg},
  organization    = {MedTech Symposium},
  isbn      = {978-3-940402-06-6},
  doi       = {10.17185/duepublico/40821},
  pages     = {54 -- 55},
  year      = {2016},
  language  = {en}
}
@article{FrotscherKochStaat2015,
  author    = {Frotscher, Ralf and Koch, Jan-Peter and Staat, Manfred},
  title     = {Computational investigation of drug action on human-induced stem cell derived cardiomyocytes},
  series = {Journal of biomechanical engineering},
  volume    = {Vol. 137},
  journal   = {Journal of biomechanical engineering},
  number    = {iss. 7},
  publisher = {ASME},
  address   = {New York},
  issn      = {1528-8951 (E-Journal); 0148-0731 (Print)},
  doi       = {10.1115/1.4030173},
  pages     = {071002-1 -- 071002-7},
  year      = {2015},
  language  = {en}
}
@article{BhattaraiStaat2018,
  author    = {Bhattarai, Aroj and Staat, Manfred},
  title     = {Computational comparison of different textile implants to correct apical prolapse in females},
  series = {Current Directions in Biomedical Engineering},
  volume    = {4},
  journal   = {Current Directions in Biomedical Engineering},
  number    = {1},
  publisher = {De Gruyter},
  address   = {Berlin},
  doi       = {10.1515/cdbme-2018-0159},
  pages     = {661 -- 664},
  year      = {2018},
  abstract  = {Prosthetic textile implants of different shapes, sizes and polymers are used to correct the apical prolapse after hysterectomy (removal of the uterus). The selection of the implant before or during minimally invasive surgery depends on the patient's anatomical defect, intended function after reconstruction and most importantly the surgeon's preference. Weakness or damage of the supporting tissues during childbirth, menopause or previous pelvic surgeries may put females in higher risk of prolapse. Numerical simulations of reconstructed pelvic floor with weakened tissues and organ supported by textile product models: DynaMesh®-PRS soft, DynaMesh®-PRP soft and DynaMesh®-CESA from FEG Textiletechnik mbH, Germany are compared.},
  language  = {en}
}
@incollection{BhattaraiFrotscherStaat2018,
  author    = {Bhattarai, Aroj and Frotscher, Ralf and Staat, Manfred},
  title     = {Computational Analysis of Pelvic Floor Dysfunction},
  series = {Women's Health and Biomechanics},
  booktitle = {Women's Health and Biomechanics},
  publisher = {Springer},
  address   = {Cham},
  isbn      = {978-3-319-71574-2},
  doi       = {10.1007/978-3-319-71574-2_17},
  pages     = {217 -- 230},
  year      = {2018},
  abstract  = {Pelvic floor dysfunction (PFD) is characterized by the failure of the levator ani (LA) muscle to maintain the pelvic hiatus, resulting in the descent of the pelvic organs below the pubococcygeal line. This chapter adopts the modified Humphrey material model to consider the effect of the muscle fiber on passive stretching of the LA muscle. The deformation of the LA muscle subjected to intra-abdominal pressure during Valsalva maneuver is compared with the magnetic resonance imaging (MRI) examination of a nulliparous female. Numerical result shows that the fiber-based Humphrey model simulates the muscle behavior better than isotropic constitutive models. Greater posterior movement of the LA muscle widens the levator hiatus due to lack of support from the anococcygeal ligament and the perineal structure as a consequence of birth-related injury and aging. Old and multiparous females with uncontrolled urogenital and rectal hiatus tend to develop PFDs such as prolapse and incontinence.},
  language  = {en}
}
@article{SchierenKleinschmidtSchmutzetal.2019,
  author    = {Schieren, Mark and Kleinschmidt, Joris and Schmutz, Axel and Loop, Torsten and Gatzweiler, Karl-Heinz and Staat, Manfred and Wappler, Frank and Defosse, Jerome},
  title     = {Comparison of forces acting on maxillary incisors during tracheal intubation with different laryngoscopy techniques: a blinded manikin study},
  series = {Anaesthesia},
  volume    = {74},
  journal   = {Anaesthesia},
  number    = {12},
  publisher = {Wiley-Blackwell},
  address   = {Oxford},
  isbn      = {1365-2044},
  doi       = {10.1111/anae.14815},
  year      = {2019},
  language  = {en}
}