@inproceedings{FingerdeVriesVosetal.2020,
  author    = {Finger, Felix and de Vries, Reynard and Vos, Roelof and Braun, Carsten and Bil, Cees},
  title     = {A comparison of hybrid-electric aircraft sizing methods},
  series = {AIAA Scitech 2020 Forum},
  booktitle = {AIAA Scitech 2020 Forum},
  doi       = {10.2514/6.2020-1006},
  pages     = {31 Seiten},
  year      = {2020},
  abstract  = {The number of case studies focusing on hybrid-electric aircraft is steadily increasing, since these configurations are thought to lead to lower operating costs and environmental impact than traditional aircraft. However, due to the lack of reference data of actual hybrid-electric aircraft, in most cases, the design tools and results are difficult to validate. In this paper, two independently developed approaches for hybrid-electric conceptual aircraft design are compared. An existing 19-seat commuter aircraft is selected as the conventional baseline, and both design tools are used to size that aircraft. The aircraft is then re-sized under consideration of hybrid-electric propulsion technology. This is performed for parallel, serial, and fully-electric powertrain architectures. Finally, sensitivity studies are conducted to assess the validity of the basic assumptions and approaches regarding the design of hybrid-electric aircraft. Both methods are found to predict the maximum take-off mass (MTOM) of the reference aircraft with less than 4\% error. The MTOM and payload-range energy efficiency of various (hybrid-) electric configurations are predicted with a maximum difference of approximately 2\% and 5\%, respectively. The results of this study confirm a correct formulation and implementation of the two design methods, and the data obtained can be used by researchers to benchmark and validate their design tools.},
  language  = {en}
}
@inproceedings{GoettenFingerHavermannetal.2019,
  author    = {G{\"o}tten, Falk and Finger, Felix and Havermann, Marc and Braun, Carsten and Marino, Matthew and Bil, Cees},
  title     = {A highly automated method for simulating airfoil characteristics at low Reynolds number using a RANS - transition approach},
  series = {Deutscher Luft- und Raumfahrtkongress - DLRK 2019. Darmstadt, Germany},
  booktitle = {Deutscher Luft- und Raumfahrtkongress - DLRK 2019. Darmstadt, Germany},
  doi       = {10.25967/490026},
  pages     = {1 -- 14},
  year      = {2019},
  language  = {en}
}
@inproceedings{FingerBraunBil2017,
  author    = {Finger, Felix and Braun, Carsten and Bil, Cees},
  title     = {A Review of Configuration Design for Distributed Propulsion Transitioning VTOL Aircraft},
  series = {Asia-Pacific International Symposium on Aerospace Technology 2017, APISAT 2017, Seoul, Korea},
  booktitle = {Asia-Pacific International Symposium on Aerospace Technology 2017, APISAT 2017, Seoul, Korea},
  pages     = {15 Seiten},
  year      = {2017},
  language  = {en}
}
@inproceedings{GoettenFingerMarinoetal.2019,
  author    = {G{\"o}tten, Falk and Finger, Felix and Marino, Matthew and Bil, Cees and Havermann, Marc and Braun, Carsten},
  title     = {A review of guidelines and best practices for subsonic aerodynamic simulations using RANS CFD},
  series = {Asia-Pacific International Symposium on Aerospace Technology (APISAT), At Gold Coast, Australia, 04. - 06. Dezember 2019},
  booktitle = {Asia-Pacific International Symposium on Aerospace Technology (APISAT), At Gold Coast, Australia, 04. - 06. Dezember 2019},
  isbn      = {978-1-925627-40-4},
  pages     = {19 Seiten},
  year      = {2019},
  language  = {de}
}
@inproceedings{FingerKhalsaKreyeretal.2019,
  author    = {Finger, Felix and Khalsa, R. and Kreyer, J{\"o}rg and Mayntz, Joscha and Braun, Carsten and Dahmann, Peter and Esch, Thomas and Kemper, Hans and Schmitz, O. and Bragard, Michael},
  title     = {An approach to propulsion system modelling for the conceptual design of hybrid-electric general aviation aircraft},
  series = {Deutscher Luft- und Raumfahrtkongress 2019, 30.9.-2.10.2019, Darmstadt},
  booktitle = {Deutscher Luft- und Raumfahrtkongress 2019, 30.9.-2.10.2019, Darmstadt},
  pages     = {15 Seiten},
  year      = {2019},
  abstract  = {In this paper, an approach to propulsion system modelling for hybrid-electric general aviation aircraft is presented. Because the focus is on general aviation aircraft, only combinations of electric motors and reciprocating combustion engines are explored. Gas turbine hybrids will not be considered. The level of the component's models is appropriate for the conceptual design stage. They are simple and adaptable, so that a wide range of designs with morphologically different propulsive system architectures can be quickly compared. Modelling strategies for both mass and efficiency of each part of the propulsion system (engine, motor, battery and propeller) will be presented.},
  language  = {en}
}
@inproceedings{FingerBraunBil2018,
  author    = {Finger, Felix and Braun, Carsten and Bil, Cees},
  title     = {An Initial Sizing Methodology for Hybrid-Electric Light Aircraft},
  series = {AIAA AVIATION Forum 2018 Aviation Technology, Integration, and Operations Conference, Atlanta, Georgia, June 25 - 29, 2018},
  booktitle = {AIAA AVIATION Forum 2018 Aviation Technology, Integration, and Operations Conference, Atlanta, Georgia, June 25 - 29, 2018},
  doi       = {10.2514/6.2018-4229},
  year      = {2018},
  language  = {en}
}
@inproceedings{ReimerBraunBallmann2006,
  author    = {Reimer, Lars and Braun, Carsten and Ballmann, Josef},
  title     = {Analysis of the static and dynamic aero-structural response of an elastic swept wing model by direct aeroelastic simulation},
  series = {ICAS 2006 proceedings : 25th Congress of the International Council of the Aeronautical Sciences ; Hamburg, Germany, 3 - 8 September, 2006 : 25th International Congress of Aeronautical Sciences},
  booktitle = {ICAS 2006 proceedings : 25th Congress of the International Council of the Aeronautical Sciences ; Hamburg, Germany, 3 - 8 September, 2006 : 25th International Congress of Aeronautical Sciences},
  publisher = {Optimage},
  address   = {Edinburgh},
  organization    = {International Council of the Aeronautical Sciences (ICAS)},
  isbn      = {0-9533991-7-6},
  pages     = {Paper No. 2006-10.3.3},
  year      = {2006},
  language  = {en}
}
@inproceedings{FingerBraunBil2018,
  author    = {Finger, Felix and Braun, Carsten and Bil, Cees},
  title     = {Case studies in initial sizing for hybrid-electric general aviation aircraft},
  series = {2018 AIAA/IEEE Electric Aircraft Technologies Symposium, Cincinnati, Ohio},
  booktitle = {2018 AIAA/IEEE Electric Aircraft Technologies Symposium, Cincinnati, Ohio},
  doi       = {10.2514/6.2018-5005},
  year      = {2018},
  language  = {en}
}
@inproceedings{FingerBraunBil2020,
  author    = {Finger, Felix and Braun, Carsten and Bil, Cees},
  title     = {Comparative assessment of parallel-hybrid-electric propulsion systems for four different aircraft},
  series = {AIAA Scitech 2020 Forum},
  booktitle = {AIAA Scitech 2020 Forum},
  doi       = {10.2514/6.2020-1502},
  pages     = {15 Seiten},
  year      = {2020},
  abstract  = {As battery technologies advance, electric propulsion concepts are on the edge of disrupting aviation markets. However, until electric energy storage systems are ready to allow fully electric aircraft, the combination of combustion engine and electric motor as a hybrid-electric propulsion system seems to be a promising intermediate solution. Consequently, the design space for future aircraft is expanded considerably, as serial-hybrid-, parallel-hybrid-, fully-electric, and conventional propulsion systems must all be considered. While the best propulsion system depends on a multitude of requirements and considerations, trends can be observed for certain types of aircraft and certain types of missions. This paper provides insight into some factors that drive a new design towards either conventional or hybrid propulsion systems. General aviation aircraft, VTOL air taxis, transport aircraft, and UAVs are chosen as case studies. Typical missions for each class are considered, and the aircraft are analyzed regarding their take-off mass and primary energy consumption. For these case studies, a high-level approach is chosen, using an initial sizing methodology. Results indicate that hybrid-electric propulsion systems should be considered if the propulsion system is sized by short-duration power constraints (e.g. take-off, climb). However, if the propulsion system is sized by a continuous power requirement (e.g. cruise), hybrid-electric systems offer hardly any benefit.},
  language  = {en}
}
@inproceedings{ReimerBraunChenetal.2007,
  author    = {Reimer, Lars and Braun, Carsten and Chen, B.-H. and Ballmann, Josef},
  title     = {Computational aeroelastic analysis and design of the HIRENASD wind tunnel wing model and tests},
  series = {Proceedings / IFASD 2007, CEAS/AIAA/KTH International Forum on Aeroelasticity and Structural Dynamics : June 18 - 21, 2007, Stockholm, Sweden},
  booktitle = {Proceedings / IFASD 2007, CEAS/AIAA/KTH International Forum on Aeroelasticity and Structural Dynamics : June 18 - 21, 2007, Stockholm, Sweden},
  publisher = {KTH},
  address   = {Stockholm},
  pages     = {1 CD-ROM},
  year      = {2007},
  language  = {en}
}
@inproceedings{FingerGoettenBraunetal.2019,
  author    = {Finger, Felix and G{\"o}tten, Falk and Braun, Carsten and Bil, Cees},
  title     = {Cost Estimation Methods for Hybrid-Electric General Aviation Aircraft},
  series = {Asia Pacific International Symposium on Aerospace Technology. APISAT 2019},
  booktitle = {Asia Pacific International Symposium on Aerospace Technology. APISAT 2019},
  pages     = {1 -- 13},
  year      = {2019},
  language  = {en}
}
@inproceedings{KorschDafnisReimerdesetal.2006,
  author    = {Korsch, Helge and Dafnis, Athanasios and Reimerdes, Hans-G{\"u}nther and Braun, Carsten and Ballmann, Josef},
  title     = {Dynamic qualification of the HIRENASD elastic wing model},
  series = {Motto: Luft- und Raumfahrt: Lehre, Forschung, Industrie - gemeinsam innovativ. Deutscher Luft- und Raumfahrtkongress 2006 : Braunschweig, 06. bis 09. November 2006. Jahrbuch / Deutsche Gesellschaft f{\"u}r Luft- und Raumfahrt. 2006},
  booktitle = {Motto: Luft- und Raumfahrt: Lehre, Forschung, Industrie - gemeinsam innovativ. Deutscher Luft- und Raumfahrtkongress 2006 : Braunschweig, 06. bis 09. November 2006. Jahrbuch / Deutsche Gesellschaft f{\"u}r Luft- und Raumfahrt. 2006},
  publisher = {Dt. Gesellschaft f{\"u}r Luft- und Raumfahrt - Lilienthal-Oberth (DGLR)},
  address   = {Bonn},
  pages     = {1441 -- 1450},
  year      = {2006},
  language  = {en}
}
@inproceedings{SchildtMarzoccaBraunetal.2019,
  author    = {Schildt, Philipp and Marzocca, Pier and Braun, Carsten and Dahmann, Peter and Keimer, Jona},
  title     = {Effects of atmospheric excitation on vibration based condition monitoring methods for hybrid-electric aircraft propulsion systems},
  series = {AIAC 2018: 18th Australian International Aerospace Congress: HUMS - 11th Defence Science and Technology (DST) International Conference on Health and Usage Monitoring (HUMS 2019): ISSFD - 27th International Symposium on Space Flight Dynamics (ISSFD)},
  booktitle = {AIAC 2018: 18th Australian International Aerospace Congress: HUMS - 11th Defence Science and Technology (DST) International Conference on Health and Usage Monitoring (HUMS 2019): ISSFD - 27th International Symposium on Space Flight Dynamics (ISSFD)},
  isbn      = {9781925627213},
  pages     = {923 -- 928},
  year      = {2019},
  language  = {en}
}
@inproceedings{Braun2008,
  author    = {Braun, Carsten},
  title     = {Ein modulares Verfahren f{\"u}r die numerische aeroelastische Analyse von Luftfahrzeugen},
  series = {Motto: Wissen und Visionen f{\"u}r ein nachhaltiges Wachstum : Deutscher Luft- und Raumfahrtkongress 2008, Darmstadt, 23. bis 25. September 2008 / Deutsche Gesellschaft f{\"u}r Luft- und Raumfahrt - Lilienthal-Oberth e.V. (DGLR). DGLR-Jahrbuch. 2008},
  booktitle = {Motto: Wissen und Visionen f{\"u}r ein nachhaltiges Wachstum : Deutscher Luft- und Raumfahrtkongress 2008, Darmstadt, 23. bis 25. September 2008 / Deutsche Gesellschaft f{\"u}r Luft- und Raumfahrt - Lilienthal-Oberth e.V. (DGLR). DGLR-Jahrbuch. 2008},
  publisher = {DGLR},
  address   = {Bonn},
  pages     = {787 -- 796},
  year      = {2008},
  language  = {de}
}
@inproceedings{GoettenFingerBraunetal.2019,
  author    = {G{\"o}tten, Falk and Finger, Felix and Braun, Carsten and Havermann, Marc and Bil, C. and Gomez, F.},
  title     = {Empirical Correlations for Geometry Build-Up of Fixed Wing Unmanned Air Vehicles},
  series = {APISAT 2018: The Proceedings of the 2018 Asia-Pacific International Symposium on Aerospace Technology (APISAT 2018)},
  booktitle = {APISAT 2018: The Proceedings of the 2018 Asia-Pacific International Symposium on Aerospace Technology (APISAT 2018)},
  publisher = {Springer},
  address   = {Singapore},
  isbn      = {978-981-13-3305-7},
  doi       = {10.1007/978-981-13-3305-7_109},
  pages     = {1365 -- 1381},
  year      = {2019},
  abstract  = {The results of a statistical investigation of 42 fixed-wing, small to medium sized (20 kg-1000 kg) reconnaissance unmanned air vehicles (UAVs) are presented. Regression analyses are used to identify correlations of the most relevant geometry dimensions with the UAV's maximum take-off mass. The findings allow an empirical based geometry-build up for a complete unmanned aircraft by referring to its take-off mass only. This provides a bridge between very early design stages (initial sizing) and the later determination of shapes and dimensions. The correlations might be integrated into a UAV sizing environment and allow designers to implement more sophisticated drag and weight estimation methods in this process. Additional information on correlation factors for a rough drag estimation methodology indicate how this technique can significantly enhance the accuracy of early design iterations.},
  language  = {en}
}
@inproceedings{ThomaFisherBertrandetal.2020,
  author    = {Thoma, Andreas and Fisher, Alex and Bertrand, Olivier and Braun, Carsten},
  title     = {Evaluation of possible flight strategies for close object evasion from bumblebee experiments},
  series = {Living Machines 2020: Biomimetic and Biohybrid Systems},
  booktitle = {Living Machines 2020: Biomimetic and Biohybrid Systems},
  editor    = {Vouloutsi, Vasiliki and Mura, Anna and Tauber, Falk and Speck, Thomas and Prescott, Tony J. and Verschure, Paul F. M. J.},
  publisher = {Springer},
  address   = {Cham},
  isbn      = {978-3-030-64312-6},
  doi       = {10.1007/978-3-030-64313-3_34},
  pages     = {354 -- 365},
  year      = {2020},
  language  = {en}
}
@inproceedings{SchildtBraunMarcocca2017,
  author    = {Schildt, P. and Braun, Carsten and Marcocca, P.},
  title     = {Flight testing the extra 330LE flying testbed},
  series = {48th Annual International Symposium of the Society of Flight Test Engineers 2017},
  booktitle = {48th Annual International Symposium of the Society of Flight Test Engineers 2017},
  isbn      = {978-151085387-4},
  pages     = {349 -- 362},
  year      = {2017},
  language  = {en}
}
@inproceedings{GoettenFingerHavermannetal.2020,
  author    = {G{\"o}tten, Falk and Finger, Felix and Havermann, Marc and Braun, Carsten and Marino, Matthew and Bil, Cees},
  title     = {Full Configuration Drag Estimation of Small-to-Medium Range UAVs and its Impact on Initial Sizing Optimization},
  series = {CEAS Aeronautical Journal},
  volume    = {12},
  booktitle = {CEAS Aeronautical Journal},
  publisher = {Springer},
  address   = {Wien},
  issn      = {1869-5590},
  doi       = {10.1007/s13272-021-00522-w},
  pages     = {589 -- 603},
  year      = {2020},
  abstract  = {The paper presents the derivation of a new equivalent skin friction coefficient for estimating the parasitic drag of short-to-medium range fixed-wing unmanned aircraft. The new coefficient is derived from an aerodynamic analysis of ten different unmanned aircraft used on surveillance, reconnaissance, and search and rescue missions. The aircraft are simulated using a validated unsteady Reynolds-averaged Navier Stokes approach. The UAV's parasitic drag is significantly influenced by the presence of miscellaneous components like fixed landing gears or electro-optical sensor turrets. These components are responsible for almost half of an unmanned aircraft's total parasitic drag. The new equivalent skin friction coefficient accounts for these effects and is significantly higher compared to other aircraft categories. It is used to initially size an unmanned aircraft for a typical reconnaissance mission. The improved parasitic drag estimation yields a much heavier unmanned aircraft when compared to the sizing results using available drag data of manned aircraft.},
  language  = {en}
}
@inproceedings{FingerBraunBil2019,
  author    = {Finger, Felix and Braun, Carsten and Bil, Cees},
  title     = {Impact of Engine Failure Constraints on the Initial Sizing of Hybrid-Electric GA Aircraft},
  series = {AIAA Scitech 2019 Forum},
  booktitle = {AIAA Scitech 2019 Forum},
  doi       = {10.2514/6.2019-1812},
  year      = {2019},
  language  = {en}
}
@inproceedings{LudowicyRingsFingeretal.2019,
  author    = {Ludowicy, Jonas and Rings, Ren{\´e} and Finger, Felix and Braun, Carsten and Bil, Cees},
  title     = {Impact of Propulsion Technology Levels on the Sizing and Energy Consumption for Serial HybridElectric General Aviation Aircraft},
  series = {Asia Pacific International Symposium on Aerospace Technology. APISAT 2019},
  booktitle = {Asia Pacific International Symposium on Aerospace Technology. APISAT 2019},
  pages     = {14 Seiten},
  year      = {2019},
  language  = {en}
}
@inproceedings{ThomaFisherBraun2020,
  author    = {Thoma, Andreas and Fisher, Alex and Braun, Carsten},
  title     = {Improving the px4 avoid algorithm by bio-inspired flight strategies},
  series = {DLRK2020 - „Luft- und Raumfahrt - Verantwortung in allen Dimensionen"},
  booktitle = {DLRK2020 - „Luft- und Raumfahrt - Verantwortung in allen Dimensionen"},
  doi       = {10.25967/530183},
  pages     = {10 Seiten},
  year      = {2020},
  language  = {en}
}
@inproceedings{FingerGoettenBraun2018,
  author    = {Finger, Felix and G{\"o}tten, Falk and Braun, Carsten},
  title     = {Initial Sizing for a Family of Hybrid-Electric VTOL General Aviation Aircraft},
  series = {67. Deutscher Luft- und Raumfahrtkongress 2018},
  booktitle = {67. Deutscher Luft- und Raumfahrtkongress 2018},
  pages     = {14 S.},
  year      = {2018},
  language  = {en}
}
@inproceedings{FingerGoettenBraunetal.2019,
  author    = {Finger, Felix and G{\"o}tten, Falk and Braun, Carsten and Bil, Cees},
  title     = {Mass, Primary Energy, and Cost - The Impact of Optimization Objectives on the Initial Sizing of Hybrid-Electric General Aviation Aircraft},
  series = {Deutscher Luft- und Raumfahrtkongress 2019, DLRK 2019. Darmstadt, Germany},
  booktitle = {Deutscher Luft- und Raumfahrtkongress 2019, DLRK 2019. Darmstadt, Germany},
  doi       = {10.25967/490012},
  pages     = {1 -- 17},
  year      = {2019},
  language  = {en}
}
@inproceedings{KapoorBraunBoller2010,
  author    = {Kapoor, Hrshi and Braun, Carsten and Boller, Christian},
  title     = {Modelling and optimisation of maintenance intervals to realize structural health monitoring applications on aircraft},
  series = {Structural health monitoring 2010 : proceedings of the Fifth European Workshop on Structural Health Monitoring held at Sorrento, Naples, Italy, June 28 - July 4, 2010 ; [EWSHM]},
  booktitle = {Structural health monitoring 2010 : proceedings of the Fifth European Workshop on Structural Health Monitoring held at Sorrento, Naples, Italy, June 28 - July 4, 2010 ; [EWSHM]},
  editor    = {Casciati, Fabio},
  publisher = {DEStech Publ.},
  address   = {Lancaster, Pa.},
  isbn      = {978-1-60595-024-2},
  pages     = {55 -- 63},
  year      = {2010},
  language  = {en}
}
@inproceedings{WellmerChenBraunetal.2007,
  author    = {Wellmer, Georg and Chen, B.-H. and Braun, Carsten and Ballmann, Josef},
  title     = {Numerical prediction of aeroelastic effects on twin-sting-rig mounted models for rear fuselage and empennage flow investigation in transonic windtunnel},
  series = {Proceedings / IFASD 2007, CEAS/AIAA/KTH International Forum on Aeroelasticity and Structural Dynamics, June 18 - 21, 2007, Stockholm, Sweden},
  booktitle = {Proceedings / IFASD 2007, CEAS/AIAA/KTH International Forum on Aeroelasticity and Structural Dynamics, June 18 - 21, 2007, Stockholm, Sweden},
  publisher = {KTH},
  address   = {Stockholm},
  organization    = {Confederation of European Aerospace Societies ; American Institute of Aeronautics and Astronautics, Reston, Va. ; Kungliga Tekniska H{\"o}gskolan, Stockholm},
  pages     = {1 CD-ROM},
  year      = {2007},
  language  = {en}
}
@inproceedings{BraunBouckeBallmann2005,
  author    = {Braun, Carsten and Boucke, Alexander and Ballmann, Josef},
  title     = {Numerical prediction of the wing deformation of a high speed transport aircraft type wind tunnel model by direct aeroelastic simulation},
  series = {Conference proceedings : CEAS/AIAA/DGLR International Forum on Aeroelasticity and Structural Dynamics IFASD 2005 : M{\"u}nchen, June 28 - July 1, 2005. DGLR-Bericht. 2005,04},
  booktitle = {Conference proceedings : CEAS/AIAA/DGLR International Forum on Aeroelasticity and Structural Dynamics IFASD 2005 : M{\"u}nchen, June 28 - July 1, 2005. DGLR-Bericht. 2005,04},
  publisher = {DGLR},
  address   = {Bonn},
  isbn      = {3-932182-43-X},
  pages     = {1 CD-ROM},
  year      = {2005},
  language  = {en}
}
@inproceedings{FingerGoettenBraunetal.2019,
  author    = {Finger, Felix and G{\"o}tten, Falk and Braun, Carsten and Bil, C.},
  title     = {On Aircraft Design Under the Consideration of Hybrid-Electric Propulsion Systems},
  series = {APISAT 2018: The Proceedings of the 2018 Asia-Pacific International Symposium on Aerospace Technology (APISAT 2018)},
  booktitle = {APISAT 2018: The Proceedings of the 2018 Asia-Pacific International Symposium on Aerospace Technology (APISAT 2018)},
  publisher = {Springer},
  address   = {Singapore},
  isbn      = {978-981-13-3305-7},
  doi       = {10.1007/978-981-13-3305-7_99},
  pages     = {1261 -- 1272},
  year      = {2019},
  abstract  = {A hybrid-electric propulsion system combines the advantages of fuel-based systems and battery powered systems and offers new design freedom. To take full advantage of this technology, aircraft designers must be aware of its key differences, compared to conventional, carbon-fuel based, propulsion systems. This paper gives an overview of the challenges and potential benefits associated with the design of aircraft that use hybrid-electric propulsion systems. It offers an introduction of the most popular hybrid-electric propulsion architectures and critically assess them against the conventional and fully electric propulsion configurations. The effects on operational aspects and design aspects are covered. Special consideration is given to the application of hybrid-electric propulsion technology to both unmanned and vertical take-off and landing aircraft. The authors conclude that electric propulsion technology has the potential to revolutionize aircraft design. However, new and innovative methods must be researched, to realize the full benefit of the technology.},
  language  = {en}
}
@inproceedings{GoettenHavermannBraunetal.2018,
  author    = {G{\"o}tten, Falk and Havermann, Marc and Braun, Carsten and Gomez, Francisco and Bil, Cees},
  title     = {On the Applicability of Empirical Drag Estimation Methods for Unmanned Air Vehicle Design Read More: https://arc.aiaa.org/doi/10.2514/6.2018-3192},
  series = {2018 Aviation Technology, Integration, and Operations Conference, AIAA AVIATION Forum},
  booktitle = {2018 Aviation Technology, Integration, and Operations Conference, AIAA AVIATION Forum},
  issn      = {1533-385X},
  doi       = {10.2514/6.2018-3192},
  pages     = {Article 3192},
  year      = {2018},
  language  = {en}
}
@inproceedings{MoehrenBergmannJanseretal.2023,
  author    = {M{\"o}hren, Felix and Bergmann, Ole and Janser, Frank and Braun, Carsten},
  title     = {On the determination of harmonic propeller loads},
  series = {AIAA SCITECH 2023 Forum},
  booktitle = {AIAA SCITECH 2023 Forum},
  publisher = {AIAA},
  doi       = {10.2514/6.2023-2404},
  pages     = {12 Seiten},
  year      = {2023},
  abstract  = {Dynamic loads significantly impact the structural design of propeller blades due to fatigue and static strength. Since propellers are elastic structures, deformations and aerodynamic loads are coupled. In the past, propeller manufacturers established procedures to determine unsteady aerodynamic loads and the structural response with analytical steady-state calculations. According to the approach, aeroelastic coupling primarily consists of torsional deformations. They neglect bending deformations, deformation velocities, and inertia terms. This paper validates the assumptions above for a General Aviation propeller and a lift propeller for urban air mobility or large cargo drones. Fully coupled reduced-order simulations determine the dynamic loads in the time domain. A quasi-steady blade element momentum approach transfers loads to one-dimensional finite beam elements. The simulation results are in relatively good agreement with the analytical method for the General Aviation propeller but show increasing errors for the slender lift propeller. The analytical approach is modified to consider the induced velocities. Still, inertia and velocity proportional terms play a significant role for the lift propeller due to increased elasticity. The assumption that only torsional deformations significantly impact the dynamic loads of propellers is not valid. Adequate determination of dynamic loads of such designs requires coupled aeroelastic simulations or advanced analytical procedures.},
  language  = {en}
}
@inproceedings{ThomaStiemerBraunetal.2023,
  author    = {Thoma, Andreas and Stiemer, Luc and Braun, Carsten and Fisher, Alex and Gardi, Alessandro G.},
  title     = {Potential of hybrid neural network local path planner for small UAV in urban environments},
  series = {AIAA SCITECH 2023 Forum},
  booktitle = {AIAA SCITECH 2023 Forum},
  publisher = {AIAA},
  address   = {Reston, Va.},
  doi       = {10.2514/6.2023-2359},
  pages     = {13 Seiten},
  year      = {2023},
  abstract  = {This work proposes a hybrid algorithm combining an Artificial Neural Network (ANN) with a conventional local path planner to navigate UAVs efficiently in various unknown urban environments. The proposed method of a Hybrid Artificial Neural Network Avoidance System is called HANNAS. The ANN analyses a video stream and classifies the current environment. This information about the current Environment is used to set several control parameters of a conventional local path planner, the 3DVFH*. The local path planner then plans the path toward a specific goal point based on distance data from a depth camera. We trained and tested a state-of-the-art image segmentation algorithm, PP-LiteSeg. The proposed HANNAS method reaches a failure probability of 17\%, which is less than half the failure probability of the baseline and around half the failure probability of an improved, bio-inspired version of the 3DVFH*. The proposed HANNAS method does not show any disadvantages regarding flight time or flight distance.},
  language  = {en}
}
@inproceedings{HippeFingerGoettenetal.2020,
  author    = {Hippe, Jonas and Finger, Felix and G{\"o}tten, Falk and Braun, Carsten},
  title     = {Propulsion System Qualification of a 25 kg VTOL-UAV: Hover Performance of Single and Coaxial Rotors and Wind-Tunnel Experiments on Cruise Propellers},
  series = {Deutscher Luft- und Raumfahrtkongress - DLRK 2020},
  booktitle = {Deutscher Luft- und Raumfahrtkongress - DLRK 2020},
  year      = {2020},
  abstract  = {This paper presents an approach for UAV propulsion system qualification and validation on the example of FH Aachen's 25 kg cargo UAV "PhoenAIX". Thrust and power consumption are the most important aspects of a propulsion system's layout. In the initial design phase, manufacturers' data has to be trusted, but the validation of components is an essential step in the design process. This process is presented in this paper. The vertical takeoff system is designed for efficient hover; therefore, performance under static conditions is paramount. Because an octo-copter layout with coaxial rotors is considered, the impact of this design choice is analyzed. Data on thrust, voltage stability, power consumption, rotational speed, and temperature development of motors and controllers are presented for different rotors. The fixed-wing propulsion system is designed for efficient cruise flight. At the same time, a certain static thrust has to be provided, as the aircraft needs to accelerate to cruise speed. As for the hover-system, data on different propellers is compared. The measurements were taken for static conditions, as well as for different inflow velocities, using the FH-Aachen's wind-tunnel.},
  language  = {en}
}
@inproceedings{RingsLudowicyFingeretal.2019,
  author    = {Rings, Ren{\´e} and Ludowicy, Jonas and Finger, Felix and Braun, Carsten and Bil, Cees},
  title     = {Sensitivity Analysis of General Aviation Aircraft with Parallel Hybrid-Electric Propulsion Systems},
  series = {Asia Pacific International Symposium on Aerospace Technology. APISAT 2019},
  booktitle = {Asia Pacific International Symposium on Aerospace Technology. APISAT 2019},
  pages     = {14 Seiten},
  year      = {2019},
  language  = {en}
}
@inproceedings{LudowicyRingsFingeretal.2018,
  author    = {Ludowicy, Jonas and Rings, Ren{\´e} and Finger, Felix and Braun, Carsten},
  title     = {Sizing Studies of Light Aircraft with Parallel Hybrid Propulsion Systems},
  series = {Deutscher Luft- und Raumfahrtkongress 2018},
  booktitle = {Deutscher Luft- und Raumfahrtkongress 2018},
  doi       = {10.25967/480227},
  pages     = {15 S.},
  year      = {2018},
  language  = {en}
}
@inproceedings{LudowicyRingsFingeretal.2018,
  author    = {Ludowicy, Jonas and Rings, Ren{\´e} and Finger, Felix and Braun, Carsten},
  title     = {Sizing Studies of Light Aircraft with Serial Hybrid Propulsion Systems},
  series = {Luft- und Raumfahrt - Digitalisierung und Vernetzung : Deutscher Luft- und Raumfahrtkongress 2018. 4. - 6. September 2018 - Friedrichshafen},
  booktitle = {Luft- und Raumfahrt - Digitalisierung und Vernetzung : Deutscher Luft- und Raumfahrtkongress 2018. 4. - 6. September 2018 - Friedrichshafen},
  pages     = {11 S.},
  year      = {2018},
  language  = {en}
}
@inproceedings{KapoorBollerGiljohannetal.2010,
  author    = {Kapoor, Hrshi and Boller, Christian and Giljohann, Sebastian and Braun, Carsten},
  title     = {Strategies for structural health monitoring implementation potential assessment in aircraft operational life extension considerations},
  series = {2nd International Symposium on NDT in Aerospace : November 22-24, 2010 Hamburg, Germany},
  booktitle = {2nd International Symposium on NDT in Aerospace : November 22-24, 2010 Hamburg, Germany},
  publisher = {Dt. Gesellschaft f{\"u}r Zerst{\"o}rungsfreie Pr{\"u}fung},
  address   = {Berlin},
  organization    = {Deutsche Gesellschaft f{\"u}r Zerst{\"o}rungsfreie Pr{\"u}fung},
  isbn      = {978-3-940283-28-3},
  pages     = {9},
  year      = {2010},
  language  = {en}
}
@inproceedings{BallmannDafnisBraunetal.2006,
  author    = {Ballmann, Josef and Dafnis, Athanasios and Braun, Carsten and Korsch, Helge and Reimerdes, Hans-G{\"u}nther and Braun, Carsten and Ballmann, Josef},
  title     = {The HIRENASD project: High Reynolds number aerostructural dynamics experiments in the European Transonic Wind Tunnel (ETW)},
  series = {ICAS 2006 proceedings : 25th Congress of the International Council of the Aeronautical Sciences ; Hamburg, Germany, 3 - 8 September, 2006 : 25th International Congress of Aeronautical Sciences},
  booktitle = {ICAS 2006 proceedings : 25th Congress of the International Council of the Aeronautical Sciences ; Hamburg, Germany, 3 - 8 September, 2006 : 25th International Congress of Aeronautical Sciences},
  publisher = {Optimage},
  address   = {Edinburgh},
  organization    = {International Council of the Aeronautical Sciences (ICAS)},
  isbn      = {0-9533991-7-6},
  pages     = {Paper No. 2006-5.11.2},
  year      = {2006},
  language  = {en}
}
@inproceedings{FingerBraunBil2017,
  author    = {Finger, Felix and Braun, Carsten and Bil, Cees},
  title     = {The Impact of Electric Propulsion on the Performance of VTOL UAVs},
  series = {Deutscher Luft- und Raumfahrtkongress 2017, DLRK , M{\"u}nchen},
  booktitle = {Deutscher Luft- und Raumfahrtkongress 2017, DLRK , M{\"u}nchen},
  year      = {2017},
  language  = {en}
}