@article{MiyamotoItabashiWagneretal.2014,
  author    = {Miyamoto, Ko-ichiro and Itabashi, Akinori and Wagner, Torsten and Sch{\"o}ning, Michael Josef and Yoshinobu, Tatsuo},
  title     = {High-speed chemical imaging inside a microfluidic channel},
  series = {Sensors and actuators. B: Chemical},
  volume    = {194},
  journal   = {Sensors and actuators. B: Chemical},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1873-3077 (E-Journal); 0925-4005 (Print)},
  doi       = {10.1016/j.snb.2013.12.090},
  pages     = {521 -- 527},
  year      = {2014},
  abstract  = {In this study, a high-speed chemical imaging system was developed for visualization of the interior of a microfluidic channel. A microfluidic channel was constructed on the sensor surface of the light-addressable potentiometric sensor (LAPS), on which the ion concentrations could be measured in parallel at up to 64 points illuminated by optical fibers. The temporal change of pH distribution inside the microfluidic channel was recorded at a maximum rate of 100 frames per second (fps). The high frame rate allowed visualization of moving interfaces and plugs in the channel even at a flow velocity of 111 mm/s, which suggests the feasibility of plug-based microfluidic devices for flow-injection analysis (FIA).},
  language  = {en}
}
@article{SiqueiraMolinnusBegingetal.2014,
  author    = {Siqueira, Jose R. and Molinnus, Denise and Beging, Stefan and Sch{\"o}ning, Michael Josef},
  title     = {Incorporating a hybrid urease-carbon nanotubes sensitive nanofilm on capacitive field-effect sensors for urea detection},
  series = {Analytical chemistry},
  volume    = {86},
  journal   = {Analytical chemistry},
  number    = {11},
  publisher = {ACS Publications},
  address   = {Columbus},
  issn      = {1520-6882 (E-Journal); 0003-2700 (Print); 0096-4484 (Print)},
  doi       = {10.1021/ac500458s},
  pages     = {5370 -- 5375},
  year      = {2014},
  abstract  = {The ideal combination among biomolecules and nanomaterials is the key for reaching biosensing units with high sensitivity. The challenge, however, is to find out a stable and sensitive film architecture that can be incorporated on the sensor's surface. In this paper, we report on the benefits of incorporating a layer-by-layer (LbL) nanofilm of polyamidoamine (PAMAM) dendrimer and carbon nanotubes (CNTs) on capacitive electrolyte-insulator-semiconductor (EIS) field-effect sensors for detecting urea. Three sensor arrangements were studied in order to investigate the adequate film architecture, involving the LbL film with the enzyme urease: (i) urease immobilized directly onto a bare EIS [EIS-urease] sensor; (ii) urease atop the LbL film over the EIS [EIS-(PAMAM/CNT)-urease] sensor; and (iii) urease sandwiched between the LbL film and another CNT layer [EIS-(PAMAM/CNT)-urease-CNT]. The surface morphology of all three urea-based EIS biosensors was investigated by atomic force microscopy (AFM), while the biosensing abilities were studied by means of capacitance-voltage (C/V) and dynamic constant-capacitance (ConCap) measureaments at urea concentrations ranging from 0.1 mM to 100 mM. The EIS-urease and EIS-(PAMAM/CNT)-urease sensors showed similar sensitivity (∼18 mV/decade) and a nonregular signal behavior as the urea concentration increased. On the other hand, the EIS-(PAMAM/CNT)-urease-CNT sensor exhibited a superior output signal performance and higher sensitivity of about 33 mV/decade. The presence of the additional CNT layer was decisive to achieve a urea based EIS sensor with enhanced properties. Such sensitive architecture demonstrates that the incorporation of an adequate hybrid enzyme-nanofilm as sensing unit opens new prospects for biosensing applications using the field-effect sensor platform.},
  language  = {en}
}
@article{MuribYeapMartensetal.2014,
  author    = {Murib, Mohammed Sharif and Yeap, Weng-Siang and Martens, Daan and Bienstman, Peter and Ceuninck, Ward de and Grinsven, Bart van and Sch{\"o}ning, Michael Josef and Michiels, Luc and Haenen, Ken and Ameloot, Marcel and Serpeng{\"u}zel, Ali and Wagner, Patrick},
  title     = {Photonic detection and characterization of DNA using sapphire microspheres},
  series = {Journal of biomedical optics},
  volume    = {19},
  journal   = {Journal of biomedical optics},
  number    = {9},
  publisher = {SPIE},
  address   = {Bellingham},
  issn      = {1560-2281 (E-Journal); 1083-3668 (Print)},
  doi       = {10.1117/1.JBO.19.9.097006},
  pages     = {097006},
  year      = {2014},
  abstract  = {A microcavity-based deoxyribonucleic acid (DNA) optical biosensor is demonstrated for the first time using synthetic sapphire for the optical cavity. Transmitted and elastic scattering intensity at 1510 nm are analyzed from a sapphire microsphere (radius 500  μm, refractive index 1.77) on an optical fiber half coupler. The 0.43 nm angular mode spacing of the resonances correlates well with the optical size of the sapphire sphere. Probe DNA consisting of a 36-mer fragment was covalently immobilized on a sapphire microsphere and hybridized with a 29-mer target DNA. Whispering gallery modes (WGMs) were monitored before the sapphire was functionalized with DNA and after it was functionalized with single-stranded DNA (ssDNA) and double-stranded DNA (dsDNA). The shift in WGMs from the surface modification with DNA was measured and correlated well with the estimated thickness of the add-on DNA layer. It is shown that ssDNA is more uniformly oriented on the sapphire surface than dsDNA. In addition, it is shown that functionalization of the sapphire spherical surface with DNA does not affect the quality factor (Q≈104) of the sapphire microspheres. The use of sapphire is especially interesting because this material is chemically resilient, biocompatible, and widely used for medical implants.},
  language  = {en}
}
@article{GuoMiyamotoWagneretal.2014,
  author    = {Guo, Yuanyuan and Miyamoto, Ko-ichiro and Wagner, Torsten and Sch{\"o}ning, Michael Josef and Yoshinobu, Tatsuo},
  title     = {Device simulation of the light-addressable potentiometric sensor for the investigation of the spatial resolution},
  series = {Sensors and actuators B: Chemical},
  volume    = {204},
  journal   = {Sensors and actuators B: Chemical},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1873-3077 (E-Journal); 0925-4005 (Print)},
  doi       = {10.1016/j.snb.2014.08.016},
  pages     = {659 -- 665},
  year      = {2014},
  abstract  = {As a semiconductor-based electrochemical sensor, the light-addressable potentiometric sensor (LAPS) can realize two dimensional visualization of (bio-)chemical reactions at the sensor surface addressed by localized illumination. Thanks to this imaging capability, various applications in biochemical and biomedical fields are expected, for which the spatial resolution is critically significant. In this study, therefore, the spatial resolution of the LAPS was investigated in detail based on the device simulation. By calculating the spatiotemporal change of the distributions of electrons and holes inside the semiconductor layer in response to a modulated illumination, the photocurrent response as well as the spatial resolution was obtained as a function of various parameters such as the thickness of the Si substrate, the doping concentration, the wavelength and the intensity of illumination. The simulation results verified that both thinning the semiconductor substrate and increasing the doping concentration could improve the spatial resolution, which were in good agreement with known experimental results and theoretical analysis. More importantly, new findings of interests were also obtained. As for the dependence on the wavelength of illumination, it was found that the known dependence was not always the case. When the Si substrate was thick, a longer wavelength resulted in a higher spatial resolution which was known by experiments. When the Si substrate was thin, however, a longer wavelength of light resulted in a lower spatial resolution. This finding was explained as an effect of raised concentration of carriers, which reduced the thickness of the space charge region. The device simulation was found to be helpful to understand the relationship between the spatial resolution and device parameters, to understand the physics behind it, and to optimize the device structure and measurement conditions for realizing higher performance of chemical imaging systems.},
  language  = {en}
}
@article{ReisertGeisslerWeileretal.2015,
  author    = {Reisert, Steffen and Geissler, H. and Weiler, C. and Wagner, P. and Sch{\"o}ning, Michael Josef},
  title     = {Multiple sensor-type system for monitoring the microbicidal effectiveness of aseptic sterilisation processes},
  series = {Food control},
  volume    = {47},
  journal   = {Food control},
  issn      = {1873-7129 (E-Journal); 0956-7135 (Print)},
  doi       = {10.1016/j.foodcont.2014.07.063},
  pages     = {615 -- 622},
  year      = {2015},
  abstract  = {The present work describes a novel multiple sensor-type system for the real-time analysis of aseptic sterilisation processes employing gaseous hydrogen peroxide (H2O2) as a sterilant. The inactivation kinetics of Bacillus atrophaeus by gaseous H2O2 have been investigated by means of a methodical calibration experiment, taking into account the process variables H2O2 concentration, humidity and gas temperature. It has been found that the microbicidal effectiveness at H2O2 concentrations above 2\% v/v is largely determined by the concentration itself, while at lower H2O2 concentrations, the gas temperature and humidity play a leading role. Furthermore, the responses of different types of gas sensors towards the influencing factors of the sterilisation process have been analysed within the same experiment. Based on a correlation established between the inactivation kinetics and the sensor responses, a calorimetric H2O2 sensor and a metal-oxide semiconductor (MOX) sensor have been identified as possible candidates for monitoring the microbicidal effectiveness of aseptic sterilisation processes employing gaseous H2O2. Therefore, two linear models that describe the relationship between sensor response and microbicidal effectiveness have been proposed.},
  language  = {en}
}
@article{KhaydukovaZadorozhnayaKirsanovetal.2014,
  author    = {Khaydukova, M. M. and Zadorozhnaya, O. A. and Kirsanov, D. O. and Iken, Heiko and Rolka, David and Sch{\"o}ning, Michael Josef and Babain, V. A. and Vlasov, Yu. G. and Legin, A. V.},
  title     = {Multivariate processing of atomic-force microscopy images for detection of the response of plasticized polymeric membranes},
  series = {Russian journal of applied chemistry},
  volume    = {87},
  journal   = {Russian journal of applied chemistry},
  number    = {3},
  publisher = {Springer},
  address   = {Dordrecht},
  issn      = {1608-3296 (E-Journal); 1070-4272 (Print)},
  doi       = {10.1134/S1070427214030112},
  pages     = {307 -- 314},
  year      = {2014},
  abstract  = {The possibility of using the atomic-force microscopy as a method for detection of the analytical signal from plasticized polymeric sensor membranes was analyzed. The surfaces of cadmium-selective membranes based on two polymeric matrices were examined. The digital images were processed with multivariate image analysis techniques. A correlation was found between the surface profile of an ion-selective membrane and the concentration of the ion in solution.},
  language  = {en}
}
@article{SchusserPoghossianBaeckeretal.2015,
  author    = {Schusser, Sebastian and Poghossian, Arshak and B{\"a}cker, Matthias and Krischer, M. and Leinhos, Marcel and Wagner, P. and Sch{\"o}ning, Michael Josef},
  title     = {An application of field-effect sensors for in-situ monitoring of degradation of biopolymers},
  series = {Sensors and actuators B: Chemical},
  volume    = {207, Part B},
  journal   = {Sensors and actuators B: Chemical},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1873-3077 (E-Journal); 0925-4005 (Print)},
  doi       = {10.1016/j.snb.2014.10.058},
  pages     = {954 -- 959},
  year      = {2015},
  abstract  = {The characterization of the degradation kinetics of biodegradable polymers is mandatory with regard to their proper application. In the present work, polymer-modified electrolyte-insulator-semiconductor (PMEIS) field-effect sensors have been applied for in-situ monitoring of the pH-dependent degradation kinetics of the commercially available biopolymer poly(d,l-lactic acid) (PDLLA) in buffer solutions from pH 3 to pH 13. PDLLA films of 500 nm thickness were deposited on the surface of an Al-p-Si-SiO2-Ta2O5 structure from a polymer solution by means of spin-coating method. The PMEIS sensor is, in principle, capable to detect any changes in bulk, surface and interface properties of the polymer induced by degradation processes. A faster degradation has been observed for PDLLA films exposed to alkaline solutions (pH 9, pH 11 and pH 13).},
  language  = {en}
}
@article{YoshinobuMiyamotoWagneretal.2015,
  author    = {Yoshinobu, Tatsuo and Miyamoto, Ko-ichiro and Wagner, Torsten and Sch{\"o}ning, Michael Josef},
  title     = {Recent developments of chemical imaging sensor systems based on the principle of the light-addressable potentiometric sensor},
  series = {Sensors and actuators B: Chemical},
  volume    = {207, Part B},
  journal   = {Sensors and actuators B: Chemical},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1873-3077 (E-Journal); 0925-4005 (Print)},
  doi       = {10.1016/j.snb.2014.09.002},
  pages     = {926 -- 932},
  year      = {2015},
  abstract  = {The light-addressable potentiometric sensor (LAPS) is an electrochemical sensor with a field-effect structure to detect the variation of the Nernst potential at its sensor surface, the measured area on which is defined by illumination. Thanks to this light-addressability, the LAPS can be applied to chemical imaging sensor systems, which can visualize the two-dimensional distribution of a particular target ion on the sensor surface. Chemical imaging sensor systems are expected to be useful for analysis of reaction and diffusion in various electrochemical and biological samples. Recent developments of LAPS-based chemical imaging sensor systems, in terms of the spatial resolution, measurement speed, image quality, miniaturization and integration with microfluidic devices, are summarized and discussed.},
  language  = {en}
}
@article{MuribYeapMartensetal.2015,
  author    = {Murib, M. S. and Yeap, W. S. and Martens, D. and Liu, X. and Bienstman, P. and Fahlman, M. and Sch{\"o}ning, Michael Josef and Michiels, L. and Haenen, K. and Serpeng{\"u}zel, A. and Wagner, Patrick},
  title     = {Photonic studies on polymer-coated sapphire-spheres : a model system for biological ligands},
  series = {Sensors and actuators A: Physical},
  volume    = {222},
  journal   = {Sensors and actuators A: Physical},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1873-3069 (E-Journal); 0924-4247 (Print)},
  doi       = {10.1016/j.sna.2014.11.024},
  pages     = {212 -- 219},
  year      = {2015},
  abstract  = {In this study we show an optical biosensor concept, based on elastic light scattering from sapphire microspheres. Transmitted and elastic scattering intensity of the microspheres (radius 500 μm, refractive index 1.77) on an optical fiber half coupler is analyzed at 1510 nm. The 0.43 nm angular mode spacing of the resonances is comparable to the angular mode spacing value estimated using the optical size of the microsphere. The spectral linewidths of the resonances are in the order of 0.01 nm, which corresponds to quality factors of approximately 105. A polydopamine layer is used as a functionalizing agent on sapphire microspherical resonators in view of biosensor implementation. The varying layer thickness on the microsphere is determined as a function of the resonance wavelength shift. It is shown that polymer functionalization has a minor effect on the quality factor. This is a promising step toward the development of an optical biosensor.},
  language  = {en}
}
@article{GuoSekiMiyamotoetal.2014,
  author    = {Guo, Yuanyuan and Seki, Kosuke and Miyamoto, Ko-ichiro and Wagner, Torsten and Sch{\"o}ning, Michael Josef and Yoshinobu, Tatsuo},
  title     = {Device simulation of the light-addressable potentiometric sensor with a novel photoexcitation method for a higher spatial resolution},
  series = {Procedia Engineering},
  volume    = {87},
  journal   = {Procedia Engineering},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1877-7058},
  doi       = {10.1016/j.proeng.2014.11.369},
  pages     = {456 -- 459},
  year      = {2014},
  abstract  = {A novel photoexcitation method for the light-addressable potentiometric sensor (LAPS) realized a higher spatial resolution of chemical imaging. In this method, a modulated light probe, which generates the alternating photocurrent signal, is surrounded by a ring of constant light, which suppresses the lateral diffusion of photocarriers by enhancing recombination. A device simulation verified that a higher spatial resolution could be obtained by adjusting the gap between the modulated and constant light. It was also found that a higher intensity and a longer wavelength of constant light was more effective. However, there exists a tradeoff between the spatial resolution and the amplitude of the photocurrent, and thus, the signal-to-noise ratio. A tilted incidence of constant light was applied, which could achieve even higher resolution with a smaller loss of photocurrent.},
  language  = {en}
}
@article{MiyamotoSekiWagneretal.2014,
  author    = {Miyamoto, K. and Seki, K. and Wagner, Torsten and Sch{\"o}ning, Michael Josef and Yoshinobu, T.},
  title     = {Enhancement of the spatial resolution of the chemical imaging sensor by a hybrid fiber-optic illumination},
  series = {Procedia Engineering},
  volume    = {87},
  journal   = {Procedia Engineering},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1877-7058},
  doi       = {10.1016/j.proeng.2014.11.563},
  pages     = {612 -- 615},
  year      = {2014},
  abstract  = {The chemical imaging sensor, which is based on the principle of the light-addressable potentiometric sensor (LAPS), is a powerful tool to visualize the spatial distribution of chemical species on the sensor surface. The spatial resolution of this sensor depends on the diffusion of photocarriers excited by a modulated light. In this study, a novel hybrid fiber-optic illumination was developed to enhance the spatial resolution. It consists of a modulated light probe to generate a photocurrent signal and a ring of constant light, which suppresses the lateral diffusion of minority carriers excited by the modulated light. It is demonstrated that the spatial resolution was improved from 92 μm to 68 μm.},
  language  = {en}
}
@article{BronderWuPoghossianetal.2014,
  author    = {Bronder, Thomas and Wu, Chunsheng and Poghossian, Arshak and Werner, Frederik and Keusgen, M. and Sch{\"o}ning, Michael Josef},
  title     = {Label-free detection of DNA hybridization with light-addressable potentiometric sensors: comparison of various DNA-immobilization strategies},
  series = {Procedia Engineering},
  volume    = {87},
  journal   = {Procedia Engineering},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1877-7058},
  doi       = {10.1016/j.proeng.2014.11.647},
  pages     = {755 -- 758},
  year      = {2014},
  abstract  = {Light-addressable potentiometric sensors (LAPS) consisting of a p-Si-SiO2 and p-Si-SiO2-Au structure, respectively, have been tested for a label-free electrical detection of DNA (deoxyribonucleic acid) hybridization. Three different strategies for immobilizing single-stranded probe DNA (ssDNA) molecules on a LAPS surface have been studied and compared: (a) immobilization of thiol-modified ssDNA on the patterned Au surface via gold-thiol bond, (b) covalent immobilization of amino-modified ssDNA onto the SiO2 surface functionalized with 3-aminopropyltriethoxysilane and (c) layer-by-layer adsorption of negatively charged ssDNA on a positively charged weak polyelectrolyte layer of poly(allylamine hydrochloride).},
  language  = {en}
}
@article{HuckPoghossianBaeckeretal.2014,
  author    = {Huck, Christina and Poghossian, Arshak and B{\"a}cker, Matthias and Reisert, Steffen and Schubert, J. and Zander, W. and Begoyan, V. K. and Buniatyan, V. V. and Sch{\"o}ning, Michael Josef},
  title     = {Chemical sensors based on a high-k perovskite oxide of barium strontium titanate},
  series = {Procedia Engineering},
  volume    = {87},
  journal   = {Procedia Engineering},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1877-7058},
  doi       = {10.1016/j.proeng.2014.11.258},
  pages     = {28 -- 31},
  year      = {2014},
  abstract  = {High-k perovskite oxide of barium strontium titanate (BST) represents a very attractive multi-functional transducer material for the development of (bio-)chemical sensors for liquids. In this work, BST films have been applied as a sensitive transducer material for a label-free detection of adsorbed charged macromolecules (positively charged polyelectrolytes) and concentration of hydrogen peroxide vapor as well as protection insulator layer for a contactless electrolyte-conductivity sensor. The experimental results of characterization of individual sensors are presented. Special emphasis is devoted towards the development of a capacitively-coupled contactless electrolyte-conductivity sensor.},
  language  = {en}
}
@article{SchusserBaeckerKrischeretal.2014,
  author    = {Schusser, Sebastian and B{\"a}cker, Matthias and Krischer, M. and Wenzel, L. and Leinhos, Marcel and Poghossian, Arshak and Biselli, Manfred and Wagner, P. and Sch{\"o}ning, Michael Josef},
  title     = {Enzymatically catalyzed degradation of biodegradable polymers investigated by means of a semiconductor-based field-effect sensor},
  series = {Procedia Engineering},
  volume    = {87},
  journal   = {Procedia Engineering},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1877-7058},
  doi       = {10.1016/j.proeng.2014.11.689},
  pages     = {1314 -- 1317},
  year      = {2014},
  abstract  = {A semiconductor field-effect device has been used for an enzymatically catalyzed degradation of biopolymers for the first time. This novel technique is capable to monitor the degradation process of multiple samples in situ and in real-time. As model system, the degradation of the biopolymer poly(D, L-lactic acid) has been monitored in the degradation medium containing the enzyme lipase from Rhizomucor miehei. The obtained results demonstrate the potential of capacitive field-effect sensors for degradation studies of biodegradable polymers.},
  language  = {en}
}
@article{BaeckerSchusserPoghossianetal.2014,
  author    = {B{\"a}cker, Matthias and Schusser, Sebastian and Poghossian, Arshak and Sch{\"o}ning, Michael Josef},
  title     = {Multi-Parametererfassung mit siliziumbasiertem Sensorchip: Aus Drei mach Eins},
  series = {GIT Labor-Fachzeitschrift},
  journal   = {GIT Labor-Fachzeitschrift},
  number    = {2},
  publisher = {Wiley},
  issn      = {0016-3538},
  pages     = {28 -- 30},
  year      = {2014},
  language  = {de}
}
@article{PoghossianBaeckerMayeretal.2015,
  author    = {Poghossian, Arshak and B{\"a}cker, Matthias and Mayer, Dirk and Sch{\"o}ning, Michael Josef},
  title     = {Gating capacitive field-effect sensors by the charge of nanoparticle/molecule hybrids},
  series = {Nanoscale},
  journal   = {Nanoscale},
  publisher = {Royal Society of Chemistry (RSC)},
  address   = {Cambridge},
  issn      = {2040-3372 (E-Journal); 2040-3364 (Print)},
  doi       = {10.1039/C4NR05987E},
  pages     = {1023 -- 1031},
  year      = {2015},
  language  = {en}
}
@article{SchuetzWeissbeckerHummeletal.1997,
  author    = {Sch{\"u}tz, S. and Weißbecker, B. and Hummel, Hans E. and Sch{\"o}ning, Michael Josef and Riemer, A. and Kordos, P. and L{\"u}th, H.},
  title     = {Field effect transistor-insect antenna junction},
  series = {Naturwissenschaften},
  volume    = {84},
  journal   = {Naturwissenschaften},
  issn      = {1432-1904},
  pages     = {86 -- 88},
  year      = {1997},
  language  = {en}
}
@article{ThustSchoeningFrohnhoffetal.1996,
  author    = {Thust, Marion and Sch{\"o}ning, Michael Josef and Frohnhoff, S. and Arens-Fischer, R. and Kordos, P. and L{\"u}th, H.},
  title     = {Porous silicon as a substrate material for potentiometric biosensors},
  series = {Measurement Science and Technology},
  volume    = {7},
  journal   = {Measurement Science and Technology},
  number    = {1},
  doi       = {10.1088/0957-0233/7/1/003},
  pages     = {26 -- 29},
  year      = {1996},
  language  = {en}
}
@article{SchoeningBaecker2012,
  author    = {Sch{\"o}ning, Michael Josef and B{\"a}cker, Matthias},
  title     = {Chip-basierte Sensoren f{\"u}r die Biotechnik},
  volume    = {13},
  number    = {2},
  publisher = {BIOCOM},
  address   = {Berlin},
  issn      = {1611-0854},
  year      = {2012},
  language  = {de}
}
@article{WagnerMiyamotoWerneretal.2011,
  author    = {Wagner, Torsten and Miyamoto, K. and Werner, Frederik and Sch{\"o}ning, Michael Josef and Yoshinobu, T.},
  title     = {Utilising Digital Micro-Mirror Device (DMD) as Scanning Light Source for Light-Addressable Potentiometric Sensors (LAPS)},
  volume    = {9},
  number    = {2},
  publisher = {American Scientific Publishers},
  address   = {Stevenson Ranch, Calif.},
  doi       = {10.1166/sl.2011.1620},
  pages     = {812 -- 815},
  year      = {2011},
  language  = {en}
}
@article{SchoeningPoghossian2006,
  author    = {Sch{\"o}ning, Michael Josef and Poghossian, Arshak},
  title     = {BioFEDs (field-effect devices) : State-of-the-art and new directions},
  series = {Electroanalysis},
  volume    = {18},
  journal   = {Electroanalysis},
  number    = {19-20},
  issn      = {1521-4109},
  doi       = {10.1002/elan.200603609},
  pages     = {1893 -- 1900},
  year      = {2006},
  language  = {en}
}
@article{SpelthahnSchubertSchoening2012,
  author    = {Spelthahn, Heiko and Schubert, J{\"u}rgen and Sch{\"o}ning, Michael Josef},
  title     = {D{\"u}nnschichtsensoren f{\"u}r die Schwermetallanalytik : Mikroelektroden auf Chalkogenidglasbasis},
  series = {GIT Labor-Fachzeitschrift},
  journal   = {GIT Labor-Fachzeitschrift},
  number    = {4},
  publisher = {Wiley-VCH},
  address   = {Weinheim},
  pages     = {285 -- 287},
  year      = {2012},
  abstract  = {Die Detektion von Schadstoffen repr{\"a}sentiert in der Umweltanalytik eine wichtige Aufgabenstellung. Gerade die Abwasser- bzw. Brauchwasseranalytik sowie die Prozesskontrolle haben einen hohen Stellenwert. Siliziumbasierte D{\"u}nnschichtsensoren bieten eine kosteng{\"u}nstige M{\"o}glichkeit, „online"-Messungen bzw. Vor-Ort-Messungen zeitnah durchzuf{\"u}hren. In dieser Arbeit wird ein potentiometrisches Sensorarray auf der Basis von Chalkogenidgl{\"a}sern zur Detektion von Schwermetallen in w{\"a}ssrigen Medien vorgestellt.},
  language  = {de}
}
@article{WarmerWagnerSchoeningetal.2015,
  author    = {Warmer, Johannes and Wagner, Patrick and Sch{\"o}ning, Michael Josef and Kaul, Peter},
  title     = {Detection of triacetone triperoxide using temperature cycled metal-oxide semiconductor gas sensors},
  series = {Physica status solidi (a)},
  volume    = {212},
  journal   = {Physica status solidi (a)},
  number    = {6},
  publisher = {Wiley-VCH},
  address   = {Weinheim},
  issn      = {1862-6319},
  doi       = {10.1002/pssa.201431882},
  pages     = {1289 -- 1298},
  year      = {2015},
  language  = {en}
}
@article{DelleHuckBaeckeretal.2015,
  author    = {Delle, Lotta E. and Huck, Christina and B{\"a}cker, Matthias and M{\"u}ller, Frank and Grandthyll, Samuel and Jacobs, Karin and Lilischkis, Rainer and Vu, Xuan T. and Sch{\"o}ning, Michael Josef and Wagner, Patrick and Thoelen, Roland and Weil, Maryam and Ingebrandt, Sven},
  title     = {Impedimetric immunosensor for the detection of histamine based on reduced graphene oxide},
  series = {Physica status solidi (a)},
  volume    = {212},
  journal   = {Physica status solidi (a)},
  number    = {6},
  publisher = {Wiley},
  address   = {Weinheim},
  issn      = {1862-6319},
  doi       = {10.1002/pssa.201431863},
  pages     = {1327 -- 1334},
  year      = {2015},
  language  = {en}
}
@article{YoshinobuMoritzFingeretal.2006,
  author    = {Yoshinobu, Tatsuo and Moritz, Werner and Finger, Friedhelm and Sch{\"o}ning, Michael Josef},
  title     = {Application of thin-film amorphous silicon to chemical imaging},
  series = {Nanostructured materials and hybrid composites for gas sensors and biomedical applications : symposium held April 18-20, 2006, San Francisco , California, U.S.A.},
  journal   = {Nanostructured materials and hybrid composites for gas sensors and biomedical applications : symposium held April 18-20, 2006, San Francisco , California, U.S.A.},
  number    = {Paper 0910-A-20-01},
  editor    = {Comini, Elisabetta},
  isbn      = {9781558998711},
  pages     = {1 -- 10},
  year      = {2006},
  language  = {en}
}
@article{SchoeningAbouzarIngebrandtetal.2006,
  author    = {Sch{\"o}ning, Michael Josef and Abouzar, Maryam H. and Ingebrandt, Sven and Platen, Johannes and Offenh{\"a}usser, Andreas and Poghossian, Arshak},
  title     = {Towards label-free detection of charged macromolecules using field-effect-based structures : Scaling down from capacitive EIS sensor over ISFET to nano-scale devices},
  series = {Nanostructured materials and hybrid composites for gas sensors and biomedical applications : symposium held April 18-20, 2006, San Francisco , California, U.S.A.},
  journal   = {Nanostructured materials and hybrid composites for gas sensors and biomedical applications : symposium held April 18-20, 2006, San Francisco , California, U.S.A.},
  number    = {paper 0915-R05-04},
  editor    = {Comini, Elisabetta},
  isbn      = {9781558998711},
  pages     = {89 -- 94},
  year      = {2006},
  language  = {en}
}
@article{TakenagaSchneiderErbayetal.2015,
  author    = {Takenaga, Shoko and Schneider, Benno and Erbay, E. and Biselli, Manfred and Schnitzler, Thomas and Sch{\"o}ning, Michael Josef and Wagner, Torsten},
  title     = {Fabrication of biocompatible lab-on-chip devices for biomedical applications by means of a 3D-printing process},
  series = {Physica status solidi (a)},
  volume    = {212},
  journal   = {Physica status solidi (a)},
  number    = {6},
  publisher = {Wiley},
  address   = {Weinheim},
  issn      = {1862-6319},
  doi       = {10.1002/pssa.201532053},
  pages     = {1347 -- 1352},
  year      = {2015},
  abstract  = {A new microfluidic assembly method for semiconductor-based biosensors using 3D-printing technologies was proposed for a rapid and cost-efficient design of new sensor systems. The microfluidic unit is designed and printed by a 3D-printer in just a few hours and assembled on a light-addressable potentiometric sensor (LAPS) chip using a photo resin. The cell growth curves obtained from culturing cells within microfluidics-based LAPS systems were compared with cell growth curves in cell culture flasks to examine biocompatibility of the 3D-printed chips. Furthermore, an optimal cell culturing within microfluidics-based LAPS chips was achieved by adjusting the fetal calf serum concentrations of the cell culture medium, an important factor for the cell proliferation.},
  language  = {en}
}
@article{MuribYeapEurlingsetal.2016,
  author    = {Murib, M. S. and Yeap, W. S. and Eurlings, Y. and Grinsven, B. van and Boyen, H.-G. and Conings, B. and Michiels, L. and Ameloot, M. and Carleer, R. and Warmer, J. and Kaul, P. and Haenen, K. and Sch{\"o}ning, Michael Josef and Ceuninck, W. de and Wagner, P.},
  title     = {Heat-transfer based characterization of DNA on synthetic sapphire chips},
  series = {Sensors and Actuators B: Chemical},
  volume    = {230},
  journal   = {Sensors and Actuators B: Chemical},
  number    = {230},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0925-4005},
  doi       = {10.1016/j.snb.2016.02.027},
  pages     = {260 -- 271},
  year      = {2016},
  abstract  = {In this study, we show that synthetic sapphire (Al₂O₃), an established implant material, can also serve as a platform material for biosensors comparable to nanocrystalline diamond. Sapphire chips, beads, and powder were first modified with (3-aminopropyl) triethoxysilane (APTES), followed by succinic anhydride (SA), and finally single-stranded probe DNA was EDC coupled to the functionalized layer. The presence of the APTES-SA layer on sapphire powders was confirmed by thermogravimetric analyis and Fourier-transform infrared spectroscopy. Using planar sapphire chips as substrates and X-ray photoelectron spectroscopy (XPS) as surface-sensitive tool, the sequence of individual layers was analyzed with respect to their chemical state, enabling the quantification of areal densities of the involved molecular units. Fluorescence microscopy was used to demonstrate the hybridization of fluorescently tagged target DNA to the probe DNA, including denaturation- and re-hybridization experiments. Due to its high thermal conductivity, synthetic sapphire is especially suitable as a chip material for the heat-transfer method, which was employed to distinguish complementary- and non-complementary DNA duplexes containing single-nucleotide polymorphisms. These results indicate that it is possible to detect mutations electronically with a chemically resilient and electrically insulating chip material.},
  language  = {en}
}
@article{SchusserKrischerBaeckeretal.2015,
  author    = {Schusser, Sebastian and Krischer, Maximillian and B{\"a}cker, Matthias and Poghossian, Arshak and Wagner, Patrick and Sch{\"o}ning, Michael Josef},
  title     = {Monitoring of the Enzymatically Catalyzed Degradation of Biodegradable Polymers by Means of Capacitive Field-Effect Sensors},
  series = {Analytical Chemistry},
  volume    = {87},
  journal   = {Analytical Chemistry},
  number    = {13},
  publisher = {ACS Publications},
  address   = {Washington, DC},
  issn      = {1520-6882},
  doi       = {10.1021/acs.analchem.5b00617},
  pages     = {6607 -- 6613},
  year      = {2015},
  abstract  = {Designing novel or optimizing existing biodegradable polymers for biomedical applications requires numerous tests on the effect of substances on the degradation process. In the present work, polymer-modified electrolyte-insulator-semiconductor (PMEIS) sensors have been applied for monitoring an enzymatically catalyzed degradation of polymers for the first time. The thin films of biodegradable polymer poly(d,l-lactic acid) and enzyme lipase were used as a model system. During degradation, the sensors were read-out by means of impedance spectroscopy. In order to interpret the data obtained from impedance measurements, an electrical equivalent circuit model was developed. In addition, morphological investigations of the polymer surface have been performed by means of in situ atomic force microscopy. The sensor signal change, which reflects the progress of degradation, indicates an accelerated degradation in the presence of the enzyme compared to hydrolysis in neutral pH buffer media. The degradation rate increases with increasing enzyme concentration. The obtained results demonstrate the potential of PMEIS sensors as a very promising tool for in situ and real-time monitoring of degradation of polymers.},
  language  = {en}
}
@article{MiyamatoSakakitaWagneretal.2015,
  author    = {Miyamato, Ko-ichiro and Sakakita, Sakura and Wagner, Torsten and Sch{\"o}ning, Michael Josef and Yoshinobu, Tatsuo},
  title     = {Application of chemical imaging sensor to in-situ pH imaging in the vicinity of a corroding metal surface},
  series = {Electrochimica Acta},
  volume    = {183},
  journal   = {Electrochimica Acta},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0013-4686},
  doi       = {10.1016/j.electacta.2015.07.184},
  pages     = {137 -- 142},
  year      = {2015},
  abstract  = {The chemical imaging sensor was applied to in-situ pH imaging of the solution in the vicinity of a corroding surface of stainless steel under potentiostatic polarization. A test piece of polished stainless steel was placed on the sensing surface leaving a narrow gap filled with artificial seawater and the stainless steel was corroded under polarization. The pH images obtained during polarization showed correspondence between the region of lower pH and the site of corrosion. It was also found that the pH value in the gap became as low as 2 by polarization, which triggered corrosion.},
  language  = {en}
}
@article{HamadBilattoAdlyetal.2016,
  author    = {Hamad, E. M. and Bilatto, S. E. R. and Adly, N. Y. and Correa, D. S. and Wolfrum, B. and Sch{\"o}ning, Michael Josef and Offenh{\"a}usser, A. and Yakushenko, A.},
  title     = {Inkjet printing of UV-curable adhesive and dielectric inks for microfluidic devices},
  series = {Lab on a Chip},
  volume    = {16},
  journal   = {Lab on a Chip},
  number    = {1},
  publisher = {Royal Society of Chemistry},
  address   = {Cambridge},
  issn      = {1473-0189},
  doi       = {10.1039/C5LC01195G},
  pages     = {70 -- 74},
  year      = {2016},
  abstract  = {Bonding of polymer-based microfluidics to polymer substrates still poses a challenge for Lab-On-a-Chip applications. Especially, when sensing elements are incorporated, patterned deposition of adhesives with curing at ambient conditions is required. Here, we demonstrate a fabrication method for fully printed microfluidic systems with sensing elements using inkjet and stereolithographic 3D-printing.},
  language  = {en}
}
@article{MiyamotoYuIsodaetal.2016,
  author    = {Miyamoto, Ko-ichiro and Yu, Bing and Isoda, Hiroko and Wagner, Torsten and Sch{\"o}ning, Michael Josef and Yoshinobu, Tatsuo},
  title     = {Visualization of the recovery process of defects in a cultured cell layer by chemical imaging sensor},
  series = {Sensors and Actuators B: Chemical},
  volume    = {236},
  journal   = {Sensors and Actuators B: Chemical},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0925-4005},
  doi       = {10.1016/j.snb.2016.04.018},
  pages     = {965 -- 969},
  year      = {2016},
  abstract  = {The chemical imaging sensor is a field-effect sensor which is able to visualize both the distribution of ions (in LAPS mode) and the distribution of impedance (in SPIM mode) in the sample. In this study, a novel cell assay is proposed, in which the chemical imaging sensor operated in SPIM mode is applied to monitor the recovery of defects in a cell layer brought into proximity of the sensing surface. A reduced impedance at a defect formed artificially in a cell layer was successfully visualized in a photocurrent image. The cell layer was cultured over two weeks, during which the temporal change of the photocurrent distribution corresponding to the recovery of the defect was observed.},
  language  = {de}
}
@article{DantismTakenagaWagneretal.2016,
  author    = {Dantism, Shahriar and Takenaga, Shoko and Wagner, Patrick and Wagner, Torsten and Sch{\"o}ning, Michael Josef},
  title     = {Determination of the extracellular acidification of Escherichia coli K12 with a multi-​chamber-​based LAPS system},
  series = {Physica status solidi (a)},
  volume    = {213},
  journal   = {Physica status solidi (a)},
  number    = {6},
  publisher = {Wiley-VCH},
  address   = {Weinheim},
  issn      = {1862-6300},
  doi       = {10.1002/pssa.201533043},
  pages     = {1479 -- 1485},
  year      = {2016},
  abstract  = {On-line monitoring of the metabolic activity of microorganisms involved in intermediate stages of biogas production plays an important role to avoid undesirable "down times" during the biogas production. In order to control this process, an on-chip differential measuring system based on the light-addressable potentiometric sensor (LAPS) principle combined with a 3D-printed multi-chamber structure has been realized. As a test microorganism, Escherichia coli K12 (E. coli K12) were used for cell-based measurements. Multi-chamber structures were developed to determine the metabolic activity of E. coli K12 in suspension for a different number of cells, responding to the addition of a constant or variable amount of glucose concentrations, enabling differential and simultaneous measurements.},
  language  = {en}
}
@article{BreuerRaueStrobeletal.2016,
  author    = {Breuer, Lars and Raue, Markus and Strobel, M. and Mang, Thomas and Sch{\"o}ning, Michael Josef and Thoelen, R. and Wagner, Torsten},
  title     = {Hydrogels with incorporated graphene oxide as light-addressable actuator materials for cell culture environments in lab-on-chip systems},
  series = {Physica status solidi (a)},
  volume    = {213},
  journal   = {Physica status solidi (a)},
  number    = {6},
  publisher = {Wiley-VCH},
  address   = {Weinheim},
  issn      = {1862-6300},
  doi       = {10.1002/pssa.201533056},
  pages     = {1520 -- 1525},
  year      = {2016},
  abstract  = {Abstractauthoren Graphene oxide (GO) nanoparticles were incorporated in temperature-sensitive Poly(N-isopropylacrylamide) (PNIPAAm) hydrogels. The nanoparticles increase the light absorption and convert light energy into heat efficiently. Thus, the hydrogels with GO can be stimulated spatially resolved by illumination as it was demonstrated by IR thermography. The temporal progression of the temperature maximum was detected for different concentrations of GO within the polymer network. Furthermore, the compatibility of PNIPAAm hydrogels with GO and cell cultures was investigated. For this purpose, culture medium was incubated with hydrogels containing GO and the viability and morphology of chinese hamster ovary (CHO) cells was examined after several days of culturing in presence of this medium.},
  language  = {en}
}
@article{BaeckerKochEibenetal.2017,
  author    = {B{\"a}cker, Matthias and Koch, Claudia and Eiben, Sabine and Geiger, Fania and Eber, Fabian and Gliemann, Hartmut and Poghossian, Arshak and Wege, Christina and Sch{\"o}ning, Michael Josef},
  title     = {Tobacco mosaic virus as enzyme nanocarrier for electrochemical biosensors},
  series = {Sensors and Actuators B: Chemical},
  volume    = {238},
  journal   = {Sensors and Actuators B: Chemical},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0925-4005},
  doi       = {10.1016/j.snb.2016.07.096},
  pages     = {716 -- 722},
  year      = {2017},
  abstract  = {The conjunction of (bio-)chemical recognition elements with nanoscale biological building blocks such as virus particles is considered as a very promising strategy for the creation of biohybrids opening novel opportunities for label-free biosensing. This work presents a new approach for the development of biosensors using tobacco mosaic virus (TMV) nanotubes or coat proteins (CPs) as enzyme nanocarriers. Sensor chips combining an array of Pt electrodes loaded with glucose oxidase (GOD)-modified TMV nanotubes or CP aggregates were used for amperometric detection of glucose as a model system for the first time. The presence of TMV nanotubes or CPs on the sensor surface allows binding of a high amount of precisely positioned enzymes without substantial loss of their activity, and may also ensure accessibility of their active centers for analyte molecules. Specific and efficient immobilization of streptavidin-conjugated GOD ([SA]-GOD) complexes on biotinylated TMV nanotubes or CPs was achieved via bioaffinity binding. These layouts were tested in parallel with glucose sensors with adsorptively immobilized [SA]-GOD, as well as [SA]-GOD crosslinked with glutardialdehyde, and came out to exhibit superior sensor performance. The achieved results underline a great potential of an integration of virus/biomolecule hybrids with electronic transducers for future applications in biosensorics and biochips.},
  language  = {en}
}
@article{DollWagnerWagneretal.2016,
  author    = {Doll, Theodor and Wagner, Torsten and Wagner, Patrick and Sch{\"o}ning, Michael Josef},
  title     = {Engineering of functional interfaces / Theodor Doll ; Torsten Wagner ; Patrick Wagner ; Michael J. Sch{\"o}ning (eds.)},
  series = {Physica status solidi (a)},
  volume    = {213},
  journal   = {Physica status solidi (a)},
  number    = {6},
  publisher = {Wiley-VCH},
  address   = {Weinheim},
  issn      = {1862-6319},
  doi       = {10.1002/pssa.201670641},
  pages     = {1393 -- 1394},
  year      = {2016},
  language  = {en}
}
@article{MiyamotoSatoAbeetal.2016,
  author    = {Miyamoto, Ko-Ichiro and Sato, Takuya and Abe, Minami and Wagner, Torsten and Sch{\"o}ning, Michael Josef and Yoshinobu, Tatsuo},
  title     = {Light-addressable potentiometric sensor as a sensing element in plug-based microfluidic devices},
  series = {Micromachines},
  volume    = {7},
  journal   = {Micromachines},
  number    = {7},
  publisher = {MDPI},
  address   = {Basel},
  issn      = {2072-666X},
  doi       = {10.3390/mi7070111},
  pages     = {111},
  year      = {2016},
  abstract  = {A plug-based microfluidic system based on the principle of the light-addressable potentiometric sensor (LAPS) is proposed. The LAPS is a semiconductor-based chemical sensor, which has a free addressability of the measurement point on the sensing surface. By combining a microfluidic device and LAPS, ion sensing can be performed anywhere inside the microfluidic channel. In this study, the sample solution to be measured was introduced into the channel in a form of a plug with a volume in the range of microliters. Taking advantage of the light-addressability, the position of the plug could be monitored and pneumatically controlled. With the developed system, the pH value of a plug with a volume down to 400 nL could be measured. As an example of plug-based operation, two plugs were merged in the channel, and the pH change was detected by differential measurement.},
  language  = {en}
}
@article{WeldenSchejaSchoeningetal.2018,
  author    = {Welden, Rene and Scheja, Sabrina and Sch{\"o}ning, Michael Josef and Wagner, Patrick and Wagner, Torsten},
  title     = {Electrochemical Evaluation of Light-Addressable Electrodes Based on TiO2 for the Integration in Lab-on-Chip Systems},
  series = {physica status solidi a : applications and materials sciences},
  volume    = {215},
  journal   = {physica status solidi a : applications and materials sciences},
  number    = {15},
  publisher = {Wiley-VCH},
  address   = {Weinheim},
  issn      = {1862-6319},
  doi       = {10.1002/pssa.201800150},
  pages     = {Article number 1800150},
  year      = {2018},
  abstract  = {In lab-on-chip systems, electrodes are important for the manipulation (e.g., cell stimulation, electrolysis) within such systems. An alternative to commonly used electrode structures can be a light-addressable electrode. Here, due to the photoelectric effect, the conducting area can be adjusted by modification of the illumination area which enables a flexible control of the electrode. In this work, titanium dioxide based light-addressable electrodes are fabricated by a sol-gel technique and a spin-coating process, to deposit a thin film on a fluorine-doped tin oxide glass. To characterize the fabricated electrodes, the thickness, and morphological structure are measured by a profilometer and a scanning electron microscope. For the electrochemical behavior, the dark current and the photocurrent are determined for various film thicknesses. For the spatial resolution behavior, the dependency of the photocurrent while changing the area of the illuminated area is studied. Furthermore, the addressing of single fluid compartments in a three-chamber system, which is added to the electrode, is demonstrated.},
  language  = {en}
}
@article{JildehOberlaenderKirchneretal.2018,
  author    = {Jildeh, Zaid B. and Oberl{\"a}nder, Jan and Kirchner, Patrick and Wagner, Patrick H. and Sch{\"o}ning, Michael Josef},
  title     = {Thermocatalytic Behavior of Manganese (IV) Oxide as Nanoporous Material on the Dissociation of a Gas Mixture Containing Hydrogen Peroxide},
  series = {Nanomaterials},
  volume    = {8},
  journal   = {Nanomaterials},
  number    = {4},
  publisher = {MDPI},
  address   = {Basel},
  issn      = {2079-4991},
  doi       = {10.3390/nano8040262},
  pages     = {Artikel 262},
  year      = {2018},
  abstract  = {In this article, we present an overview on the thermocatalytic reaction of hydrogen peroxide (H₂O₂) gas on a manganese (IV) oxide (MnO₂) catalytic structure. The principle of operation and manufacturing techniques are introduced for a calorimetric H₂O₂ gas sensor based on porous MnO₂. Results from surface analyses by X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM) of the catalytic material provide indication of the H₂O₂ dissociation reaction schemes. The correlation between theory and the experiments is documented in numerical models of the catalytic reaction. The aim of the numerical models is to provide further information on the reaction kinetics and performance enhancement of the porous MnO₂ catalyst.},
  language  = {en}
}
@article{BaeckerRakowskiKrappenetal.2017,
  author    = {B{\"a}cker, M. and Rakowski, D. and Krappen, E. and Sch{\"o}ning, Michael Josef},
  title     = {Reinigungsprozesse in der Lebensmittelindustrie. Entwicklung eines Demonstrators zur {\"U}berwachung},
  series = {GIT Labor-Fachzeitschrift},
  volume    = {61},
  journal   = {GIT Labor-Fachzeitschrift},
  number    = {8},
  publisher = {Wiley-VCH},
  address   = {Weinheim},
  issn      = {0016-3538},
  pages     = {26 -- 28},
  year      = {2017},
  language  = {de}
}
@article{KochPoghossianSchoeningetal.2018,
  author    = {Koch, Claudia and Poghossian, Arshak and Sch{\"o}ning, Michael Josef and Wege, Christian},
  title     = {Penicillin Detection by Tobacco Mosaic Virus-Assisted Colorimetric Biosensors},
  series = {Nanotheranostics},
  volume    = {2},
  journal   = {Nanotheranostics},
  number    = {2},
  publisher = {Ivyspring},
  address   = {Sydney},
  issn      = {2206-7418},
  doi       = {10.7150/ntno.22114},
  pages     = {184 -- 196},
  year      = {2018},
  abstract  = {The presentation of enzymes on viral scaffolds has beneficial effects such as an increased enzyme loading and a prolonged reusability in comparison to conventional immobilization platforms. Here, we used modified tobacco mosaic virus (TMV) nanorods as enzyme carriers in penicillin G detection for the first time. Penicillinase enzymes were conjugated with streptavidin and coupled to TMV rods by use of a bifunctional biotin-linker. Penicillinase-decorated TMV particles were characterized extensively in halochromic dye-based biosensing. Acidometric analyte detection was performed with bromcresol purple as pH indicator and spectrophotometry. The TMV-assisted sensors exhibited increased enzyme loading and strongly improved reusability, and higher analysis rates compared to layouts without viral adapters. They extended the half-life of the sensors from 4 - 6 days to 5 weeks and thus allowed an at least 8-fold longer use of the sensors. Using a commercial budget-priced penicillinase preparation, a detection limit of 100 µM penicillin was obtained. Initial experiments also indicate that the system may be transferred to label-free detection layouts.},
  language  = {en}
}
@article{PilasYaziciSelmeretal.2018,
  author    = {Pilas, Johanna and Yazici, Y. and Selmer, Thorsten and Keusgen, M. and Sch{\"o}ning, Michael Josef},
  title     = {Application of a portable multi-analyte biosensor for organic acid determination in silage},
  series = {Sensors},
  volume    = {18},
  journal   = {Sensors},
  number    = {5},
  publisher = {MDPI},
  address   = {Basel},
  issn      = {1424-8220},
  doi       = {10.3390/s18051470},
  pages     = {12 Seiten},
  year      = {2018},
  abstract  = {Multi-analyte biosensors may offer the opportunity to perform cost-effective and rapid analysis with reduced sample volume, as compared to electrochemical biosensing of each analyte individually. This work describes the development of an enzyme-based biosensor system for multi-parametric determination of four different organic acids. The biosensor array comprises five working electrodes for simultaneous sensing of ethanol, formate, d-lactate, and l-lactate, and an integrated counter electrode. Storage stability of the biosensor was evaluated under different conditions (stored at +4 °C in buffer solution and dry at -21 °C, +4 °C, and room temperature) over a period of 140 days. After repeated and regular application, the individual sensing electrodes exhibited the best stability when stored at -21 °C. Furthermore, measurements in silage samples (maize and sugarcane silage) were conducted with the portable biosensor system. Comparison with a conventional photometric technique demonstrated successful employment for rapid monitoring of complex media.},
  language  = {en}
}
@article{DantismRoehlenWagneretal.2018,
  author    = {Dantism, Shahriar and R{\"o}hlen, Desiree and Wagner, Torsten and Wagner, Patrick and Sch{\"o}ning, Michael Josef},
  title     = {Optimization of Cell-Based Multi-Chamber LAPS Measurements Utilizing FPGA-Controlled Laser-Diode Modules},
  series = {physica status solidi a : applications and materials sciences},
  volume    = {215},
  journal   = {physica status solidi a : applications and materials sciences},
  number    = {15},
  publisher = {Wiley-VCH},
  address   = {Weinheim},
  issn      = {1862-6319},
  doi       = {10.1002/pssa.201800058},
  pages     = {Article number 1800058},
  year      = {2018},
  abstract  = {A light-addressable potentiometric sensor (LAPS) is a field-effect-based potentiometric device, which detects concentration changes of an analyte solution on the sensor surface in a spatially resolved way. It uses a light source to generate electron-hole pairs inside the semiconductor, which are separated in the depletion region due to an applied bias voltage across the sensor structure and hence, a surface-potential-dependent photocurrent can be read out. However, depending on the beam angle of the light source, scattering effects can occur, which influence the recorded signal in LAPS-based differential measurements. To solve this problem, a novel illumination unit based on a field programmable gate array (FPGA) consisting of 16 small-sized tunable infrared laser-diode modules (LDMs) is developed. Due to the improved focus of the LDMs with a beam angle of only 2 mrad, undesirable scattering effects are minimized. Escherichia coli (E. coli) K12 bacteria are used as a test microorganism to study the extracellular acidification on the sensor surface. Furthermore, a salt bridge chamber is built up and integrated with the LAPS system enabling multi-chamber differential measurements with a single Ag/AgCl reference electrode.},
  language  = {en}
}
@article{VahidpourOberlaenderSchoening2018,
  author    = {Vahidpour, Farnoosh and Oberl{\"a}nder, Jan and Sch{\"o}ning, Michael Josef},
  title     = {Flexible Calorimetric Gas Sensors for Detection of a Broad Concentration Range of Gaseous Hydrogen Peroxide: A Step Forward to Online Monitoring of Food-Package Sterilization Processes},
  series = {Phys. Status Solidi A},
  volume    = {215},
  journal   = {Phys. Status Solidi A},
  number    = {15},
  publisher = {Wiley-VCH},
  address   = {Weinheim},
  doi       = {10.1002/pssa.201800044},
  pages     = {Artikel 1800044},
  year      = {2018},
  abstract  = {In this study, flexible calorimetric gas sensors are developed for specificdetection of gaseous hydrogen peroxide (H₂O₂) over a wide concentrationrange, which is used in sterilization processes for aseptic packaging industry.The flexibility of these sensors is an advantage for identifying the chemical components of the sterilant on the corners of the food boxes, so-called "coldspots", as critical locations in aseptic packaging, which are of great importance. These sensors are fabricated on flexible polyimide films by means of thin-film technique. Thin layers of titanium and platinum have been deposited on polyimide to define the conductive structures of the sensors. To detect the high-temperature evaporated H₂O₂, a differential temperature set-up is proposed. The sensors are evaluated in a laboratory-scaled sterilizationsystem to simulate the sterilization process. The concentration range of the evaporated H₂O₂ from 0 to 7.7\% v/v was defined and the sensors have successfully detected high as well as low H₂O₂ concentrations with a sensitivity of 5.04 °C/\% v/v. The characterizations of the sensors confirm their precise fabrication, high sensitivity and the novelty of low H₂O₂ concentration detections for future inline monitoring of food-package sterilization.},
  language  = {en}
}
@article{PoghossianJablonskiKochetal.2018,
  author    = {Poghossian, Arshak and Jablonski, Melanie and Koch, Claudia and Bronder, Thomas and Rolka, David and Wege, Christina and Sch{\"o}ning, Michael Josef},
  title     = {Field-effect biosensor using virus particles as scaffolds for enzyme immobilization},
  series = {Biosensors and Bioelectronics},
  volume    = {110},
  journal   = {Biosensors and Bioelectronics},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0956-5663},
  doi       = {10.1016/j.bios.2018.03.036},
  pages     = {168 -- 174},
  year      = {2018},
  abstract  = {A field-effect biosensor employing tobacco mosaic virus (TMV) particles as scaffolds for enzyme immobilization is presented. Nanotubular TMV scaffolds allow a dense immobilization of precisely positioned enzymes with retained activity. To demonstrate feasibility of this new strategy, a penicillin sensor has been developed by coupling a penicillinase with virus particles as a model system. The developed field-effect penicillin biosensor consists of an Al-p-Si-SiO₂-Ta₂O₅-TMV structure and has been electrochemically characterized in buffer solutions containing different concentrations of penicillin G. In addition, the morphology of the biosensor surface with virus particles was characterized by scanning electron microscopy and atomic force microscopy methods. The sensors possessed a high penicillin sensitivity of ~ 92 mV/dec in a nearly-linear range from 0.1 mM to 10 mM, and a low detection limit of about 50 µM. The long-term stability of the penicillin biosensor was periodically tested over a time period of about one year without any significant loss of sensitivity. The biosensor has also been successfully applied for penicillin detection in bovine milk samples.},
  language  = {en}
}
@article{MoraisSilvaDantasetal.2019,
  author    = {Morais, Paulo V. and Silva, Anielle C. A. and Dantas, Noelio O. and Sch{\"o}ning, Michael Josef and Siqueira, Jos{\´e} R., Jr.},
  title     = {Hybrid Layer-by-Layer Film of Polyelectrolytes-Embedded Catalytic CoFe2O4 Nanocrystals as Sensing Units in Capacitive Electrolyte-Insulator-Semiconductor Devices},
  series = {physica status solidi a : applications and materials sciences},
  volume    = {216},
  journal   = {physica status solidi a : applications and materials sciences},
  number    = {1900044},
  publisher = {Wiley},
  address   = {Weinheim},
  doi       = {10.1002/pssa.201900044},
  pages     = {1 -- 9},
  year      = {2019},
  language  = {en}
}
@article{BreuerPilasGuthmannetal.2019,
  author    = {Breuer, Lars and Pilas, Johanna and Guthmann, Eric and Sch{\"o}ning, Michael Josef and Thoelen, Ronald and Wagner, Torsten},
  title     = {Towards light-addressable flow control: responsive hydrogels with incorporated graphene oxide as laser-driven actuator structures within microfluidic channels},
  series = {Sensor and Actuators B: Chemical},
  volume    = {288},
  journal   = {Sensor and Actuators B: Chemical},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0925-4005},
  doi       = {10.1016/j.snb.2019.02.086},
  pages     = {579 -- 585},
  year      = {2019},
  language  = {en}
}
@article{PoghossianGeisslerSchoening2019,
  author    = {Poghossian, Arshak and Geissler, Hanno and Sch{\"o}ning, Michael Josef},
  title     = {Rapid methods and sensors for milk quality monitoring and spoilage detection},
  series = {Biosensors and Bioelectronics},
  volume    = {140},
  journal   = {Biosensors and Bioelectronics},
  number    = {Article 111272},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0956-5663},
  doi       = {10.1016/j.bios.2019.04.040},
  year      = {2019},
  language  = {en}
}
@article{DantismRoehlenWagneretal.2019,
  author    = {Dantism, Shahriar and R{\"o}hlen, Desiree and Wagner, Torsten and Wagner, P. and Sch{\"o}ning, Michael Josef},
  title     = {A LAPS-based differential sensor for parallelized metabolism monitoring of various bacteria},
  series = {Sensors},
  volume    = {19},
  journal   = {Sensors},
  number    = {21},
  publisher = {MDPI},
  address   = {Basel},
  issn      = {1424-8220},
  doi       = {10.3390/s19214692},
  pages     = {Artikel 4692},
  year      = {2019},
  abstract  = {Monitoring the cellular metabolism of bacteria in (bio)fermentation processes is crucial to control and steer them, and to prevent undesired disturbances linked to metabolically inactive microorganisms. In this context, cell-based biosensors can play an important role to improve the quality and increase the yield of such processes. This work describes the simultaneous analysis of the metabolic behavior of three different types of bacteria by means of a differential light-addressable potentiometric sensor (LAPS) set-up. The study includes Lactobacillus brevis, Corynebacterium glutamicum, and Escherichia coli, which are often applied in fermentation processes in bioreactors. Differential measurements were carried out to compensate undesirable influences such as sensor signal drift, and pH value variation during the measurements. Furthermore, calibration curves of the cellular metabolism were established as a function of the glucose concentration or cell number variation with all three model microorganisms. In this context, simultaneous (bio)sensing with the multi-organism LAPS-based set-up can open new possibilities for a cost-effective, rapid detection of the extracellular acidification of bacteria on a single sensor chip. It can be applied to evaluate the metabolic response of bacteria populations in a (bio)fermentation process, for instance, in the biogas fermentation process.},
  language  = {en}
}
@article{KarschuckFilipovBollellaetal.2019,
  author    = {Karschuck, T. L. and Filipov, Y. and Bollella, P. and Sch{\"o}ning, Michael Josef and Katz, E.},
  title     = {Not-XOR (NXOR) logic gate based on an enzyme-catalyzed reaction},
  series = {International Journal of Unconventional Computing},
  volume    = {14},
  journal   = {International Journal of Unconventional Computing},
  number    = {3-4},
  publisher = {Old City Publishing},
  address   = {Philadelphia},
  issn      = {1548-7199},
  pages     = {235 -- 242},
  year      = {2019},
  abstract  = {Enzyme-catalyzed reactions have been designed to mimic various Boolean logic gates in the general framework of unconventional biomolecular computing. While some of the logic gates, particularly OR, AND, are easy to realize with biocatalytic reactions and have been reported in numerous publications, some other, like NXOR, are very challenging and have not been realized yet with enzyme reactions. The paper reports on a novel approach to mimicking the NXOR logic gate using the bell-shaped enzyme activity dependent on pH values. Shifting pH from the optimum value to the acidic or basic values by using acid or base inputs (meaning 1,0 and 0,1 inputs) inhibits the enzyme reaction, while keeping the optimum pH (assuming 0,0 and 1,1 input combinations) preserves a high enzyme activity. The challenging part of the present approach is the selection of an enzyme with a well-demonstrated bell-shape activity dependence on the pH value. While many enzymes can satisfy this condition, we selected pyrroloquinoline quinone (PQQ)-dependent glucose dehydrogenase as this enzyme has the optimum pH center-located on the pH scale allowing the enzyme activity change by the acidic and basic pH shift from the optimum value corresponding to the highest activity. The present NXOR gate is added to the biomolecular "toolbox" as a new example of Boolean logic gates based on enzyme reactions.},
  language  = {en}
}