@article{KirchnerOberlaenderFriedrichetal.2012,
  author    = {Kirchner, Patrick and Oberl{\"a}nder, Jan and Friedrich, Peter and Berger, J{\"o}rg and Rysstad, Gunnar and Sch{\"o}ning, Michael Josef and Keusgen, Michael},
  title     = {Realisation of a calorimetric gas sensor on polyimide foil for applications in aseptic food industry},
  series = {Sensors and Actuators B: Chemical},
  volume    = {170},
  journal   = {Sensors and Actuators B: Chemical},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0925-4005},
  doi       = {10.1016/j.snb.2011.01.032},
  pages     = {60 -- 66},
  year      = {2012},
  abstract  = {A calorimetric gas sensor is presented for the monitoring of vapour-phase H2O2 at elevated temperature during sterilisation processes in aseptic food industry. The sensor was built up on a flexible polyimide foil (thickness: 25 μm) that has been chosen due to its thermal stability and low thermal conductivity. The sensor set-up consists of two temperature-sensitive platinum thin-film resistances passivated by a layer of SU-8 photo resist and catalytically activated by manganese(IV) oxide. Instead of an active heating structure, the calorimetric sensor utilises the elevated temperature of the evaporated H2O2 aerosol. In an experimental test rig, the sensor has shown a sensitivity of 4.78 °C/(\%, v/v) in a H2O2 concentration range of 0\%, v/v to 8\%, v/v. Furthermore, the sensor possesses the same, unchanged sensor signal even at varied medium temperatures between 210 °C and 270 °C of the gas stream. At flow rates of the gas stream from 8 m3/h to 12 m3/h, the sensor has shown only a slightly reduced sensitivity at a low flow rate of 8 m3/h. The sensor characterisation demonstrates the suitability of the calorimetric gas sensor for monitoring the efficiency of industrial sterilisation processes.},
  language  = {en}
}
@article{KirchnerOberlaenderSusoetal.2013,
  author    = {Kirchner, Patrick and Oberl{\"a}nder, Jan and Suso, Henri-Pierre and Rysstad, Gunnar and Keusgen, Michael and Sch{\"o}ning, Michael Josef},
  title     = {Towards a wireless sensor system for real-time H2O2 monitoring in aseptic food processes},
  series = {Physica status solidi (a)},
  volume    = {210},
  journal   = {Physica status solidi (a)},
  number    = {5},
  publisher = {Wiley},
  address   = {Weinheim},
  issn      = {1862-6319},
  doi       = {10.1002/pssa.201200920},
  pages     = {877 -- 883},
  year      = {2013},
  abstract  = {A wireless sensor system based on the industrial ZigBee standard for low-rate wireless networking was developed that enables real-time monitoring of gaseous H2O2 during the package sterilization in aseptic food processes. The sensor system consists of a remote unit connected to a calorimetric gas sensor, which was already established in former works, and an external base unit connected to a laptop computer. The remote unit was built up by an XBee radio frequency (RF) module for data communication and a programmable system-on-chip controller to read out the sensor signal and process the sensor data, whereas the base unit is a second XBee RF module. For the rapid H2O2 detection on various locations inside the package that has to be sterilized, a novel read-out strategy of the calorimetric gas sensor was established, wherein the sensor response is measured within the short sterilization time and correlated with the present H2O2 concentration. In an exemplary measurement application in an aseptic filling machinery, the suitability of the new, wireless sensor system was demonstrated, wherein the influence of the gas velocity on the H2O2 distribution inside a package was determined and verified with microbiological tests.},
  language  = {en}
}