@article{GrossBergerGross2003, author = {Groß, Rolf Fritz and Berger, J. and Groß, H.}, title = {Geb{\"a}udeautomation - Betriebsdatenerfassung und Geb{\"a}udeleittechnik im Klartext}, series = {HLH. Heizung, L{\"u}ftung/Klima, Haustechnik}, volume = {54}, journal = {HLH. Heizung, L{\"u}ftung/Klima, Haustechnik}, number = {2}, publisher = {Springer}, address = {D{\"u}sseldorf}, issn = {1436-5103}, pages = {81}, year = {2003}, language = {de} } @phdthesis{Gross2002, author = {Groß, Rolf Fritz}, title = {Zur Kinetik homogener Gasphasenreaktionen nitroser Komponenten in Rauchgasen einer kohlebefeuerten Wirbelschicht}, publisher = {Shaker}, address = {Aachen}, isbn = {3-8322-0004-5 (softcover)}, pages = {X, 146 Seiten}, year = {2002}, language = {de} } @techreport{ChristGrossRenz1998, author = {Christ, Ansgar and Groß, Rolf Fritz and Renz, Ulrich}, title = {HGR: Untersuchung zur Minimierung von gasf{\"o}rmigen Schadstoffen aus Rauchgasen bei der Heißgasfiltration}, doi = {10.2314/GBV:504318411}, pages = {141 Seiten}, year = {1998}, abstract = {Gas- und Dampfturbinen-Kraftwerke mit Druckwirbelschicht- oder mit Druckvergasungsverfahren erm{\"o}glichen die Verstromung von Kohle mit hohem Wirkungsgrad und niedrigen Emissionen. Eine Voraussetzung f{\"u}r den Betrieb dieser Anlagen ist die Entstaubung der Rauchgase bei hohen Temperaturen und Dr{\"u}cken. Abreinigungsfilter mit keramischen Elementen werden dazu eingesetzt. Eine Reduzierung gasf{\"o}rmiger Schadstoffe unter den gleichen Bedingungen k{\"o}nnte Rauchgasw{\"a}sche ersetzen. Ziel des Gesamtvorhabens ist es, die Integration von Heißgasfiltration und katalytischem Abbau der Schadstoffe Kohlenmonoxid, Kohlenwasserstoffe und Stickoxide in einen Verfahrensschritt zu untersuchen. Die Arbeitsschwerpunkte dieses Teilvorhabens betreffen: die katalytische Wirkung eisenhaltiger Braunkohlenaschen, die Wirksamkeit des Calciumaluminat als Katalysator des Abbaus unverbrannter Kohlenwasserstoffe im Heißgasfilter, numerische Simulation der kombinierten Abscheidung von Partikeln und gasf{\"o}rmigen Schadstoffen aus Rauchgasen}, language = {de} } @misc{SchulzeBuxlohGrossCheng2020, author = {Schulze-Buxloh, Lina and Groß, Rolf Fritz and Cheng, Kevin Toni}, title = {Development and manufacturing of an interactive three-dimensional phase diagram of carbon dioxide for teaching sessions in thermodynamics}, series = {Proceedings of the International Conference The Future of Education 2020}, journal = {Proceedings of the International Conference The Future of Education 2020}, year = {2020}, language = {en} } @inproceedings{SchulzeBuxlohGross2021, author = {Schulze-Buxloh, Lina and Groß, Rolf Fritz}, title = {Interdisciplinary Course Smart Building Engineering: A new approach of teaching freshmen in remote teamwork project under pandemic restrictions}, series = {New Perspectives in Science Education - International Conference}, booktitle = {New Perspectives in Science Education - International Conference}, publisher = {Filodiritto}, address = {Bologna}, pages = {4 Seiten}, year = {2021}, abstract = {In the context of the Corona pandemic and its impact on teaching like digital lectures and exercises a new concept especially for freshmen in demanding courses of Smart Building Engineering became necessary. As there were hardly any face-to-face events at the university, the new teaching concept should enable a good start into engineering studies under pandemic conditions anyway and should also replace the written exam at the end. The students should become active themselves in small teams instead of listening passively to a lecture broadcast online with almost no personal contact. For this purpose, a role play was developed in which the freshmen had to work out a complete solution to the realistic problem of designing, construction planning and implementing a small guesthouse. Each student of the team had to take a certain role like architect, site manager, BIM-manager, electrician and the technitian for HVAC installations. Technical specifications must be complied with, as well as documentation, time planning and cost estimate. The final project folder had to contain technical documents like circuit diagrams for electrical components, circuit diagrams for water and heating, design calculations and components lists. On the other hand construction schedule, construction implementation plan, documentation of the construction progress and minutes of meetings between the various trades had to be submitted as well. In addition to the project folder, a model of the construction project must also be created either as a handmade model or as a digital 3D-model using Computer-aided design (CAD) software. The first steps in the field of Building information modelling (BIM) had also been taken by creating a digital model of the building showing the current planning status in real time as a digital twin. This project turned out to be an excellent training of important student competencies like teamwork, communication skills, and self -organisation and also increased motivation to work on complex technical questions. The aim of giving the student a first impression on the challenges and solutions in building projects with many different technical trades and their points of view was very well achieved and should be continued in the future.}, language = {en} } @inproceedings{MohanGrossMenzeletal.2021, author = {Mohan, Nijanthan and Groß, Rolf Fritz and Menzel, Karsten and Theis, Fabian}, title = {Opportunities and Challenges in the Implementation of Building Information Modeling for Prefabrication of Heating, Ventilation and Air Conditioning Systems in Small and Medium-Sized Contracting Companies in Germany - A Case Study}, series = {WIT Transactions on The Built Environment, Vol. 205}, booktitle = {WIT Transactions on The Built Environment, Vol. 205}, publisher = {WIT Press}, address = {Southampton}, issn = {1743-3509}, doi = {10.2495/BIM210101}, pages = {117 -- 126}, year = {2021}, abstract = {Even though BIM (Building Information Modelling) is successfully implemented in most of the world, it is still in the early stages in Germany, since the stakeholders are sceptical of its reliability and efficiency. The purpose of this paper is to analyse the opportunities and obstacles to implementing BIM for prefabrication. Among all other advantages of BIM, prefabrication is chosen for this paper because it plays a vital role in creating an impact on the time and cost factors of a construction project. The project stakeholders and participants can explicitly observe the positive impact of prefabrication, which enables the breakthrough of the scepticism factor among the small-scale construction companies. The analysis consists of the development of a process workflow for implementing prefabrication in building construction followed by a practical approach, which was executed with two case studies. It was planned in such a way that, the first case study gives a first-hand experience for the workers at the site on the BIM model so that they can make much use of the created BIM model, which is a better representation compared to the traditional 2D plan. The main aim of the first case study is to create a belief in the implementation of BIM Models, which was succeeded by the execution of offshore prefabrication in the second case study. Based on the case studies, the time analysis was made and it is inferred that the implementation of BIM for prefabrication can reduce construction time, ensures minimal wastes, better accuracy, less problem-solving at the construction site. It was observed that this process requires more planning time, better communication between different disciplines, which was the major obstacle for successful implementation. This paper was carried out from the perspective of small and medium-sized mechanical contracting companies for the private building sector in Germany.}, language = {en} } @inproceedings{SchulzeBuxlohGross2021, author = {Schulze-Buxloh, Lina and Groß, Rolf Fritz}, title = {Miniature urban farming plant: a complex educational "Toy" for engineering students}, series = {The Future of Education 11th Edition 2021}, booktitle = {The Future of Education 11th Edition 2021}, pages = {4 Seiten}, year = {2021}, abstract = {Urban farming is an innovative and sustainable way of food production and is becoming more and more important in smart city and quarter concepts. It also enables the production of certain foods in places where they usually dare not produced, such as production of fish or shrimps in large cities far away from the coast. Unfortunately, it is not always possible to show students such concepts and systems in real life as part of courses: visits of such industry plants are sometimes not possible because of distance or are permitted by the operator for hygienic reasons. In order to give the students the opportunity of getting into contact with such an urban farming system and its complex operation, an industrial urban farming plant was set up on a significantly smaller scale. Therefore, all needed technical components like water aeriation, biological and mechanical filtration or water circulation have been replaced either by aquarium components or by self-designed parts also using a 3D-printer. Students from different courses like mechanical engineering, smart building engineering, biology, electrical engineering, automation technology and civil engineering were involved in this project. This "miniature industrial plant" was also able to start operation and has now been running for two years successfully. Due to Corona pandemic, home office and remote online lectures, the automation of this miniature plant should be brought to a higher level in future for providing a good control over the system and water quality remotely. The aim of giving the student a chance to get to know the operation of an urban farming plant was very well achieved and the students had lots of fun in "playing" and learning with it in a realistic way.}, language = {en} } @article{CheenakulaGriebelMontagetal.2023, author = {Cheenakula, Dheeraja and Griebel, Kai and Montag, David and Gr{\"o}mping, Markus}, title = {Concept development of a mainstream deammonification and comparison with conventional process in terms of energy, performance and economical construction perspectives}, series = {Frontiers in Microbiology}, volume = {14}, journal = {Frontiers in Microbiology}, number = {11155235}, editor = {Huang, Xiaowu}, publisher = {Frontiers}, issn = {1664-302X}, doi = {10.3389/fmicb.2023.1155235}, pages = {1 -- 15}, year = {2023}, abstract = {Deammonification for nitrogen removal in municipal wastewater in temperate and cold climate zones is currently limited to the side stream of municipal wastewater treatment plants (MWWTP). This study developed a conceptual model of a mainstream deammonification plant, designed for 30,000 P.E., considering possible solutions corresponding to the challenging mainstream conditions in Germany. In addition, the energy-saving potential, nitrogen elimination performance and construction-related costs of mainstream deammonification were compared to a conventional plant model, having a single-stage activated sludge process with upstream denitrification. The results revealed that an additional treatment step by combining chemical precipitation and ultra-fine screening is advantageous prior the mainstream deammonification. Hereby chemical oxygen demand (COD) can be reduced by 80\% so that the COD:N ratio can be reduced from 12 to 2.5. Laboratory experiments testing mainstream conditions of temperature (8-20°C), pH (6-9) and COD:N ratio (1-6) showed an achievable volumetric nitrogen removal rate (VNRR) of at least 50 gN/(m3∙d) for various deammonifying sludges from side stream deammonification systems in the state of North Rhine-Westphalia, Germany, where m3 denotes reactor volume. Assuming a retained Norganic content of 0.0035 kgNorg./(P.E.∙d) from the daily loads of N at carbon removal stage and a VNRR of 50 gN/(m3∙d) under mainstream conditions, a resident-specific reactor volume of 0.115 m3/(P.E.) is required for mainstream deammonification. This is in the same order of magnitude as the conventional activated sludge process, i.e., 0.173 m3/(P.E.) for an MWWTP of size class of 4. The conventional plant model yielded a total specific electricity demand of 35 kWh/(P.E.∙a) for the operation of the whole MWWTP and an energy recovery potential of 15.8 kWh/(P.E.∙a) through anaerobic digestion. In contrast, the developed mainstream deammonification model plant would require only a 21.5 kWh/(P.E.∙a) energy demand and result in 24 kWh/(P.E.∙a) energy recovery potential, enabling the mainstream deammonification model plant to be self-sufficient. The retrofitting costs for the implementation of mainstream deammonification in existing conventional MWWTPs are nearly negligible as the existing units like activated sludge reactors, aerators and monitoring technology are reusable. However, the mainstream deammonification must meet the performance requirement of VNRR of about 50 gN/(m3∙d) in this case.}, language = {en} } @article{PetersonOsterPeterson2020, author = {Peterson-Oster, Madeleine and Peterson, Leif Arne}, title = {Fassadensystem: Optisch ansprechend, freistehend, elementiert und aus Eichenholz}, series = {Bauen mit Holz, Der Zimmermann}, journal = {Bauen mit Holz, Der Zimmermann}, publisher = {Rudolf M{\"u}ller}, address = {K{\"o}ln}, issn = {0005-6545}, year = {2020}, abstract = {Bei der Entwicklung des Fassadensystems ging es darum die m{\"o}gliche Dauerhaftigkeit von Holz bei direkter Bewitterung zu maximieren. Gleichzeitig soll gezeigt werden, dass mittels durchdachter Ans{\"a}tze beim konstruktiven Holzschutz und die Wahl einer geeigneten Holzart langlebige Konstruktionen realisiert werden k{\"o}nnen.}, language = {de} } @article{LepkeLilliePetersonetal.2006, author = {Lepke, Dietrich and Lillie, Dirk and Peterson, Leif Arne and Hempe, Thomas}, title = {Liegedauer von Holzschwellen in Tunneln der Hamburger Hochbahn AG}, series = {EI - Der Eisenbahningenieur}, journal = {EI - Der Eisenbahningenieur}, number = {2}, publisher = {DVV Media Group}, address = {Hamburg}, issn = {0013-2810}, pages = {46 -- 50}, year = {2006}, abstract = {Die Hamburger Hochbahn AG ben{\"o}tigte im Rahmen der {\"U}berarbeitung einer langfristigen Instandhaltungs- und Erneuerungsstrategie f{\"u}r ihre U-Bahn-Infrastruktur eine belastbare Aussage {\"u}ber die Restlebensdauer der Holzschwellen im Tunnel. Aus diesem Grunde beauftragte sie das Institut f{\"u}r Verkehrswesen, Eisenbahnbau und -betrieb (IVE) der Universit{\"a}t Hannover mit der Erstellung eines entsprechenden Gutachtens. Das Ergebnis f{\"u}hrte zu der gesicherten Aussage einer erheblich l{\"a}ngeren Restlebensdauer der Tunnelschwellen gegen{\"u}ber den bisherigen, gesch{\"a}tzten Annahmen.}, language = {de} } @phdthesis{Peterson2008, author = {Peterson, Leif Arne}, title = {Zum Tragverhalten nachgiebig verbundener Biegetr{\"a}ger aus Holz}, publisher = {Fraunhofer IRB Verlag}, address = {Stuttgart}, isbn = {9783816775973}, pages = {169 Seiten}, year = {2008}, abstract = {In der vorliegenden Dissertation werden zun{\"a}chst die linear elastischen Bemessungsm{\"o}glichkeiten f{\"u}r nachgiebig verbundene Biegetr{\"a}ger unter statischer und dynamischer Beanspruchung diskutiert. Zum Vergleich wurden praktische Untersuchungen an zweiteiligen Kantholzbiegetr{\"a}gem mit mechanischen Verbindungsmitteln unterschiedlicher Verformungscharakteristika durchgef{\"u}hrt, ebenso wie umfangreiche Materialpr{\"u}fungen an den zusammengef{\"u}gten Einzelquerschnitten. Hierdurch werden die Unterschiede zum realen, nicht elastischen, statischen Tragverhalten aufgezeigt. Der f{\"u}r das dynamische Verhalten maßgebende Systemparameter der Eigenfrequenz wird f{\"u}r mehrteilige Biegetr{\"a}ger theoretisch hinterfragt und an den nachgiebig verbundenen Kantholzbiegetr{\"a}gem gemessen. Begleitet von weiteren praktischen Untersuchungen an einzelnen Verbindungsmitteln unter Blockscherbeanspruchung wird die rechnerische Ber{\"u}cksichtigung des plastischen Verbindungsmittelverhaltens auf zwei theoretischen Wegen erforscht. Auf Grundlage der Untersuchungen wird ein neues, semianalytisches y-Verfahren entwickelt. Gegen{\"u}ber den Berechnungen mit finiten Volumen- und Kontakt-Elementen erweist sich das neue Verfahren auf Basis der, um die schubweichen Fugen erweiterten, Balkentheorie als leistungsf{\"a}higer. Der Einfluss des plastischen Verbindungsmittelverhaltens wird durch vergleichende Parameterstudien mit diesem neuen Verfahren als vom anerkannten Stand der Technik ausreichend ber{\"u}cksichtigt identifiziert. F{\"u}r die linear elastische Dimensionierung werden optimierte Verbindungsmittelanordnungen hergeleitet, die durch {\"u}bersichtliche Erg{\"a}nzungen zum existierenden Bemessungskonzept des y-Verfahrens eine exaktere Berechnung erm{\"o}glichen.}, language = {de} } @article{NabilPetersonSchmidtetal.2010, author = {Nabil, F. and Peterson, Leif Arne and Schmidt, A. and Geerdes, D.}, title = {Die Holzkuppel des Neuen Palais in Potsdam}, series = {Bauingenieur}, volume = {85}, journal = {Bauingenieur}, number = {8}, publisher = {Springer-VDI-Verlag}, address = {D{\"u}sseldorf}, issn = {0005-6650}, pages = {324 -- 330}, year = {2010}, language = {de} } @book{NebgenPeterson2015, author = {Nebgen, Nikolaus and Peterson, Leif Arne}, title = {Holzbau kompakt nach Eurocode 5}, edition = {5. Auflage}, publisher = {Beuth}, address = {Berlin}, isbn = {978-3-410-25455-3}, pages = {XII, 267 Seiten}, year = {2015}, abstract = {"Holzbau kompakt" wurde sowohl f{\"u}r Studierende als auch Praktiker konzipiert und beschr{\"a}nkt sich nicht auf reine Holzbauaufgaben, sondern setzt sich ggf. auch mit der Tragwerkslehre auseinander. Die Neuauflage basiert auf dem Eurocode 5 und ber{\"u}cksichtigt zahlreiche neue Erkenntnisse aus Forschung und praxisnaher Entwicklung. Neben den Grundlagen der Bemessung, der Baustoffe, der Dauerhaftigkeit und des Brandschutzes konzentriert sich das Grundlagenwerk besonders auf das Konstruieren mit Holz und Holzwerkstoffen, anschaulich dargestellt an sehr ausf{\"u}hrlichen Beispielen f{\"u}r Wohnhaus und Hallentragwerk.}, language = {de} } @book{HolschemacherPetersPetersonetal.2013, author = {Holschemacher, Klaus and Peters, Klaus and Peterson, Leif Arne and Schneider, Klaus-J{\"u}rgen and Thiele, Ralf}, title = {Konstruktiver Ingenieurbau kompakt: Formelsammlung und Bemessungshilfen nach Eurocode f{\"u}r die Bereiche: Lastannahmen, Holzbau, Mauerwerksbau, Stahlbau, Stahlbetonbau, Geotechnik, statische Hinweise}, edition = {4., vollst{\"a}ndig {\"u}berarbeitete Auflage}, publisher = {Beuth}, address = {Berlin}, isbn = {978-3-410-22775-5}, pages = {384 Seiten}, year = {2013}, abstract = {Das kompakte Nachschlagewerk f{\"u}r den konstruktiven Ingenieurbau wurde f{\"u}r den t{\"a}glichen Gebrauch auf der Baustelle konzipiert und stellt alle f{\"u}r die rechnerische Nachweisf{\"u}hrung und Konstruktion von Bauteilen wichtigsten Angaben in Form einer Formelsammlung mit Nachweishilfen zur Verf{\"u}gung. Der Inhalt wurde auf Basis der neuen Eurocodes komplett aktualisiert und erweitert. Die 4. Auflage enth{\"a}lt in bew{\"a}hrter Manier eine umfangreiche Formelsammlung, Querschnittswerte und Bemessungshilfen zu den Bereichen Lastannahmen, Holzbau, Mauerwerksbau, Stahlbau, Stahlbetonbau, Geotechnik sowie statische Hinweise. Farbiges Papier erleichtert den zielgerichteten Zugriff auf die einzelnen Fachgebiete.}, language = {de} } @incollection{FruehwaldPetersonHasenstab2012, author = {Fr{\"u}hwald, Katja and Peterson, Leif Arne and Hasenstab, Andreas}, title = {Pr{\"u}fverfahren zur Begutachtung der Materialeigenschaften von Holztragwerken}, series = {Bauphysik-Kalender 2012: Schwerpunkt: Geb{\"a}udediagnostik}, booktitle = {Bauphysik-Kalender 2012: Schwerpunkt: Geb{\"a}udediagnostik}, editor = {Fouad, Nabil A.}, publisher = {Ernst \& Sohn}, address = {Berlin}, isbn = {9783433029862 (Print)}, doi = {10.1002/9783433601235.ch4}, pages = {103 -- 155}, year = {2012}, abstract = {Dieses Kapitel beinhaltet: - Einleitung - Ausgew{\"a}hlte typische Sch{\"a}den an Holzbauwerken - Das Material Holz und seine Besonderheiten - Bestandserfassung - Labormethoden - Begutachtungsbeispiele - Zusammenfassung und Schlussfolgerungen - Literatur}, language = {de} } @article{BungErpicumTullis2020, author = {Bung, Daniel Bernhard and Erpicum, S{\´e}bastien and Tullis, Blanke P.}, title = {Advances in hydraulic structures engineering}, series = {Journal of Hydraulic Engineering}, volume = {147}, journal = {Journal of Hydraulic Engineering}, number = {1}, publisher = {ASCE}, address = {Reston, Va.}, issn = {0733-9429 (Druckausgabe)}, doi = {10.1061/(ASCE)HY.1943-7900.0001851}, pages = {1 Seite}, year = {2020}, language = {en} } @article{vonHaefenKrautwaldStolleetal.2022, author = {von H{\"a}fen, Hajo and Krautwald, Clemens and Stolle, Jacob and Bung, Daniel Bernhard and Goseberg, Nils}, title = {Overland flow of broken solitary waves over a two-dimensional coastal plane}, series = {Coastal Engineering}, volume = {175}, journal = {Coastal Engineering}, number = {August}, publisher = {Elsevier}, address = {Amsterdam}, issn = {1872-7379}, doi = {10.1016/j.coastaleng.2022.104125}, pages = {14 Seiten}, year = {2022}, abstract = {Landslides, rock falls or related subaerial and subaqueous mass slides can generate devastating impulse waves in adjacent waterbodies. Such waves can occur in lakes and fjords, or due to glacier calving in bays or at steep ocean coastlines. Infrastructure and residential houses along coastlines of those waterbodies are often situated on low elevation terrain, and are potentially at risk from inundation. Impulse waves, running up a uniform slope and generating an overland flow over an initially dry adjacent horizontal plane, represent a frequently found scenario, which needs to be better understood for disaster planning and mitigation. This study presents a novel set of large-scale flume test focusing on solitary waves propagating over a 1:14.5 slope and breaking onto a horizontal section. Examining the characteristics of overland flow, this study gives, for the first time, insight into the fundamental process of overland flow of a broken solitary wave: its shape and celerity, as well as its momentum when wave breaking has taken place beforehand.}, language = {en} } @book{UibelPeterson2019, author = {Uibel, Thomas and Peterson, Leif Arne}, title = {Tagungsband Aachener Holzbautagung 2019}, editor = {Uibel, Thomas and Peterson, Leif Arne}, publisher = {FH Aachen}, address = {Aachen}, issn = {2197-4489}, pages = {140 Seiten ; Illustrationen, graph. Darst.}, year = {2019}, language = {de} } @book{UibelPeterson2013, author = {Uibel, Thomas and Peterson, Leif Arne}, title = {Tagungsband Aachener Holzbautagung 2013}, editor = {Uibel, Thomas and Peterson, Leif Arne}, publisher = {FH Aachen}, address = {Aachen}, issn = {2197-4489}, pages = {76 Seiten ; Illustrationen, graph. Darst.}, year = {2013}, language = {de} } @book{UibelPeterson2023, author = {Uibel, Thomas and Peterson, Leif Arne}, title = {Tagungsband Aachener Holzbautagung 2023}, editor = {Uibel, Thomas and Peterson, Leif Arne}, publisher = {FH Aachen}, address = {Aachen}, issn = {2197-4489}, year = {2023}, language = {de} }