@book{OPUS4-4303, title = {Ingenieurfreunde FH Aachen : 75 Jahre F{\"o}rderverein; Elektrotechnik und Informationstechnik, Luft- und Raumfahrttechnik, Maschinenbau und Mechatronik / [Hrsg.: Ingenieurfreunde FH Aachen e. V. ; Red.: H. J. Raatschen]}, editor = {Raatschen, Hans-J{\"u}rgen}, publisher = {Klinkenberg}, address = {Aachen}, isbn = {978-3-941704-03-9}, pages = {112 S. : Ill., graph. Darst.}, year = {2010}, language = {de} } @article{AbbasBalcBremenetal.2022, author = {Abbas, Karim and Balc, Nicolae and Bremen, Sebastian and Skupin, Marco}, title = {Crystallization and aging behavior of polyetheretherketone PEEK within rapid tooling and rubber molding}, series = {Journal of Manufacturing and Materials Processing}, volume = {6}, journal = {Journal of Manufacturing and Materials Processing}, number = {5}, publisher = {MDPI}, address = {Basel}, issn = {2504-4494}, doi = {10.3390/jmmp6050093}, pages = {1 -- 12}, year = {2022}, abstract = {In times of short product life cycles, additive manufacturing and rapid tooling are important methods to make tool development and manufacturing more efficient. High-performance polymers are the key to mold production for prototypes and small series. However, the high temperatures during vulcanization injection molding cause thermal aging and can impair service life. The extent to which the thermal stress over the entire process chain stresses the material and whether it leads to irreversible material aging is evaluated. To this end, a mold made of PEEK is fabricated using fused filament fabrication and examined for its potential application. The mold is heated to 200 ◦C, filled with rubber, and cured. A differential scanning calorimetry analysis of each process step illustrates the crystallization behavior and first indicates the material resistance. It shows distinct cold crystallization regions at a build chamber temperature of 90 ◦C. At an ambient temperature above Tg, crystallization of 30\% is achieved, and cold crystallization no longer occurs. Additional tensile tests show a decrease in tensile strength after ten days of thermal aging. The steady decrease in recrystallization temperature indicates degradation of the additives. However, the tensile tests reveal steady embrittlement of the material due to increasing crosslinking.}, language = {en} } @article{AbbasHedwigBalcetal.2023, author = {Abbas, Karim and Hedwig, Lukas and Balc, Nicolae and Bremen, Sebastian}, title = {Advanced FFF of PEEK: Infill strategies and material characteristics for rapid tooling}, series = {Polymers}, volume = {2023}, journal = {Polymers}, number = {15}, publisher = {MDPI}, address = {Basel}, doi = {10.3390/polym15214293}, pages = {Artikel 4293}, year = {2023}, abstract = {Traditional vulcanization mold manufacturing is complex, costly, and under pressure due to shorter product lifecycles and diverse variations. Additive manufacturing using Fused Filament Fabrication and high-performance polymers like PEEK offer a promising future in this industry. This study assesses the compressive strength of various infill structures (honeycomb, grid, triangle, cubic, and gyroid) when considering two distinct build directions (Z, XY) to enhance PEEK's economic and resource efficiency in rapid tooling. A comparison with PETG samples shows the behavior of the infill strategies. Additionally, a proof of concept illustrates the application of a PEEK mold in vulcanization. A peak compressive strength of 135.6 MPa was attained in specimens that were 100\% solid and subjected to thermal post-treatment. This corresponds to a 20\% strength improvement in the Z direction. In terms of time and mechanical properties, the anisotropic grid and isotropic cubic infill have emerged for use in rapid tooling. Furthermore, the study highlights that reducing the layer thickness from 0.15 mm to 0.1 mm can result in a 15\% strength increase. The study unveils the successful utilization of a room-temperature FFF-printed PEEK mold in vulcanization injection molding. The parameters and infill strategies identified in this research enable the resource-efficient FFF printing of PEEK without compromising its strength properties. Using PEEK in rapid tooling allows a cost reduction of up to 70\% in tool production.}, language = {en} } @inproceedings{AbbasThurnKessleretal.2019, author = {Abbas, Karim and Thurn, Laura and Kessler, Julia and Eichler, Fabian}, title = {Basic research of the consideration of additive manufactured lattice structures under thermoand fluid dynamic loads}, series = {Modern technologies in manufacturing (MTeM 2019)}, volume = {299}, booktitle = {Modern technologies in manufacturing (MTeM 2019)}, number = {Article 01009}, doi = {10.1051/matecconf/201929901009}, pages = {8 Seiten}, year = {2019}, language = {en} } @article{AbdelLatifPeekenBenner1985, author = {Abdel-Latif, Lotfie Ahmed and Peeken, Heinz and Benner, Joachim}, title = {Thermohydrodynamic analysis of thrust-bearing with circular pads running on bubbly oil (BTHD-theory)}, series = {Journal of tribology}, volume = {107}, journal = {Journal of tribology}, number = {4}, isbn = {0742-4787}, issn = {1528-8897}, pages = {527 -- 537}, year = {1985}, language = {en} } @article{AbdelLatifPeekenBenner1985, author = {Abdel-Latif, Lotfie Ahmed and Peeken, Heinz and Benner, Joachim}, title = {Термогидродинамический расчет упорных подшипников с круговыми подушками на масляной пленке, содержащей пузырьки газа}, series = {Проблемы трения и смазки}, volume = {107}, journal = {Проблемы трения и смазки}, number = {4}, pages = {94 -- 102}, year = {1985}, language = {ru} } @inproceedings{AdenackerGerhardsOttenetal.2021, author = {Adenacker, J. and Gerhards, Benjamin and Otten, Christian and Schleser, Markus}, title = {Laserstrahlschweißen von Aluminium-Kupfer-Werkstoffkombinationen f{\"u}r die Elektromobilit{\"a}t}, series = {DVS CONGRESS 2021}, booktitle = {DVS CONGRESS 2021}, publisher = {DVS Media GmbH}, address = {D{\"u}sseldorf}, isbn = {978-3-96144-146-4}, pages = {31 -- 38}, year = {2021}, language = {de} } @inproceedings{AdomeitWillms1984, author = {Adomeit, G. and Willms, Herbert}, title = {Experimental investigation of the acceleration of deflagration in wake flow}, series = {Safety of thermal water reactors : proceedings of a Seminar on the Results of the European Communities' Indirect Action Research Programme on Safety of Thermal Water Reactors, held in Brussels, 1-3 October 1984 / Commission of the European Communities}, booktitle = {Safety of thermal water reactors : proceedings of a Seminar on the Results of the European Communities' Indirect Action Research Programme on Safety of Thermal Water Reactors, held in Brussels, 1-3 October 1984 / Commission of the European Communities}, editor = {Skupinski, Edwin}, publisher = {Graham \& Trotman [u.a.]}, address = {London Gaithersburg, Md.}, isbn = {0-86010-678-0}, pages = {294 -- 304}, year = {1984}, language = {en} } @techreport{AdomeitWillms1984, author = {Adomeit, G. and Willms, Herbert}, title = {Experimental investigation of the acceleration of deflagration in wake flow : final report. - (Euratom-publications-EUR ; 9593 : Nuclear science and technology)}, publisher = {Commission of the European Communities}, address = {Luxembourg}, isbn = {92-825-4699-3}, pages = {III, 119 S.}, year = {1984}, language = {en} } @article{AhmedReisgenSchleseretal.2010, author = {Ahmed, Essam and Reisgen, Uwe and Schleser, Markus and Mokrov, Oleg}, title = {On formability of tailor laser welded blanks of DP/TRIP steel sheets}, series = {Science and technology of welding and joining}, volume = {15}, journal = {Science and technology of welding and joining}, number = {5}, publisher = {Maney}, address = {Leeds}, issn = {1743-2936}, doi = {10.1179/136217110X12731414739754}, pages = {337 -- 342}, year = {2010}, abstract = {This paper aims to evaluate the formability of tailor welded blanks of dual phase (DP600)/transformation induced plasticity (TRIP700) steel sheets. In this work, bead on plate butt joints of 2·5 mm DP600 and 1·2 mm TRIP700 steel sheets were performed using CO2 laser beam welding. Microhardness measurements and transverse tensile testing were carried out to characterise the welds. The formability of base metals and welds were investigated by standard Erichsen test. In a perpendicular tensile test to the weld line, all specimens were fractured at the TRIP base metal, and the strengths were somewhat higher than those of base metal. There was a significant reduction in formability caused by welding of the DP600/TRIP700 steel sheets, and the formability increased with increasing welding speed.}, language = {en} } @inproceedings{AlhwarinFerreinGebhardtetal.2015, author = {Alhwarin, Faraj and Ferrein, Alexander and Gebhardt, Andreas and Kallweit, Stephan and Scholl, Ingrid and Tedjasukmana, Osmond Sanjaya}, title = {Improving additive manufacturing by image processing and robotic milling}, series = {2015 IEEE International Conference on Automation Science and Engineering (CASE), Aug 24-28, 2015 Gothenburg, Sweden}, booktitle = {2015 IEEE International Conference on Automation Science and Engineering (CASE), Aug 24-28, 2015 Gothenburg, Sweden}, doi = {10.1109/CoASE.2015.7294217}, pages = {924 -- 929}, year = {2015}, language = {en} } @book{Anik1983, author = {Anik, Sabri}, title = {Zum L{\"o}sungsverhalten von Sauerstoff in bin{\"a}ren Legierungen unter besonderer Ber{\"u}cksichtigung experimenteller Ergebnisse am System Kupfer-Sauerstoff-Wismut bei 1200 Grad C}, number = {Mikroform}, pages = {89, 28 S. ; 2 Mikrofiches 24x}, year = {1983}, language = {de} } @article{Anik1978, author = {Anik, Sabri}, title = {Gespritzte Metallbeschichtungen : Eigenschaften lichtbogengespritzter Stahlschichten in Abh{\"a}ngigkeit von einigen Spritzparametern}, series = {Technische Rundschau : TR ; das Schweizer Industrie-Magazin}, volume = {70}, journal = {Technische Rundschau : TR ; das Schweizer Industrie-Magazin}, number = {26}, publisher = {Medtrix Group}, address = {Basel}, issn = {0040-148X}, pages = {9 -- 13}, year = {1978}, language = {de} } @article{Anik1978, author = {Anik, Sabri}, title = {Gespritzte Metallschichten : Eigenschaften lichtbogengespritzter Stahlschichten in Abh{\"a}ngigkeit von einigen Spritzparametern}, series = {Technische Rundschau : TR ; das Schweizer Industrie-Magazin}, volume = {70}, journal = {Technische Rundschau : TR ; das Schweizer Industrie-Magazin}, number = {39}, publisher = {Medtrix Group}, address = {Basel}, issn = {0040-148X}, pages = {37 -- 41}, year = {1978}, language = {de} } @article{AnikAnik1991, author = {Anik, Sabri and Anik, Salahaddin}, title = {Stand der Schweißtechnik in der T{\"u}rkei}, series = {Schweißen und Schneiden : Fachzeitschrift f{\"u}r Schweißen und verwandte Verfahren}, volume = {43}, journal = {Schweißen und Schneiden : Fachzeitschrift f{\"u}r Schweißen und verwandte Verfahren}, number = {3}, issn = {0036-7184}, pages = {142 -- 145}, year = {1991}, language = {de} } @article{AnikDagsoez1971, author = {Anik, Sabri and Dagsoez, A. K.}, title = {Feinbleche schweißen : die Temperaturverteilung in d{\"u}nnen Stahlblechplatten beim Lichtbogenschweißen}, series = {Technische Rundschau : TR ; das Schweizer Industrie-Magazin}, volume = {63}, journal = {Technische Rundschau : TR ; das Schweizer Industrie-Magazin}, number = {9}, publisher = {Medtrix Group}, address = {Basel}, issn = {0040-148X}, pages = {57 -- 59}, year = {1971}, language = {de} } @inproceedings{AnikFrohberg1989, author = {Anik, Sabri and Frohberg, Martin G.}, title = {Thermodynamic behaviour of oxygen in molten metallic alloys}, series = {Thermochemistry of alloys : recent developments of experimental methods ; [proceedings of the NATO Advanced Study Institute on Thermochemistry of Alloys, Recent Developments of Experimental Methods, Kiel, F.R.G., August 17 - 27, 1987]. - (NATO ASI series : Series C ; 286)}, booktitle = {Thermochemistry of alloys : recent developments of experimental methods ; [proceedings of the NATO Advanced Study Institute on Thermochemistry of Alloys, Recent Developments of Experimental Methods, Kiel, F.R.G., August 17 - 27, 1987]. - (NATO ASI series : Series C ; 286)}, editor = {Brodowsky, Horst}, publisher = {Springer}, address = {Dordrecht [u.a.]}, isbn = {0-7923-0434-9}, pages = {419 -- 428}, year = {1989}, language = {en} } @article{AnikFrohberg1984, author = {Anik, Sabri and Frohberg, Martin G.}, title = {Thermodynamics and solubility of oxygen in liquid copper-lead alloys at 1200°C from E.M.F. measurements}, series = {Berichte der Bunsengesellschaft f{\"u}r physikalische Chemie}, volume = {88}, journal = {Berichte der Bunsengesellschaft f{\"u}r physikalische Chemie}, number = {8}, issn = {0940-483X}, pages = {707 -- 710}, year = {1984}, language = {en} } @article{AnikFrohberg1987, author = {Anik, Sabri and Frohberg, Martin G.}, title = {Thermodynamics and solubility of oxygen in liquid bismuth-lead and bismuth-antimony alloys}, series = {Berichte der Bunsengesellschaft f{\"u}r physikalische Chemie}, volume = {91}, journal = {Berichte der Bunsengesellschaft f{\"u}r physikalische Chemie}, number = {7}, issn = {0940-483X}, pages = {790 -- 794}, year = {1987}, language = {en} } @article{AnikFrohberg1984, author = {Anik, Sabri and Frohberg, Martin G.}, title = {Investigations of the thermodynamics of oxygen and the determination of the miscibility gap in the system copper-oxygen-lead at 12000C}, series = {Zeitschrift f{\"u}r Metallkunde}, volume = {75}, journal = {Zeitschrift f{\"u}r Metallkunde}, number = {8}, issn = {0044-3093}, pages = {586 -- 589}, year = {1984}, language = {en} } @article{AnikFrohberg1983, author = {Anik, Sabri and Frohberg, Martin G.}, title = {Investigation of the thermodynamics of oxygen and the determination of phase boundaries in the system copper-oxygen-bismuth at 12000C}, series = {Zeitschrift f{\"u}r Metallkunde}, volume = {74}, journal = {Zeitschrift f{\"u}r Metallkunde}, number = {8}, issn = {0044-3093}, pages = {530 -- 534}, year = {1983}, language = {en} } @article{AnikFrohberg1988, author = {Anik, Sabri and Frohberg, Martin G.}, title = {Thermodynamics of oxygen in the copper-antimony system at 1473K}, series = {Erzmetall : Rohstoffgewinnung, Verarbeitung, Recycling, Umwelttechnik}, volume = {41}, journal = {Erzmetall : Rohstoffgewinnung, Verarbeitung, Recycling, Umwelttechnik}, number = {10}, issn = {0044-2658}, pages = {498 -- 501}, year = {1988}, language = {en} } @article{AnikFrohbergKapoor1982, author = {Anik, Sabri and Frohberg, Martin G. and Kapoor, Madan Lal}, title = {Untersuchungen zum thermodynamischen Verhalten des Sauerstoffs in Kupfer-Wismut-Schmelzen bei 1200°C}, series = {Zeitschrift f{\"u}r Physikalische Chemie}, volume = {133}, journal = {Zeitschrift f{\"u}r Physikalische Chemie}, number = {2}, issn = {0942-9352}, pages = {167 -- 174}, year = {1982}, language = {de} } @article{AnikFrohbergKapoor1983, author = {Anik, Sabri and Frohberg, Martin G. and Kapoor, Madan Lal}, title = {Experiments and theoretical considerations on the solution of oxygen in binary metal alloys}, series = {Berichte der Bunsengesellschaft f{\"u}r physikalische Chemie}, volume = {87}, journal = {Berichte der Bunsengesellschaft f{\"u}r physikalische Chemie}, number = {12}, issn = {0005-9021}, pages = {1201 -- 1204}, year = {1983}, language = {en} } @article{AnikFrohbergKapoor1983, author = {Anik, Sabri and Frohberg, Martin G. and Kapoor, Madan Lal}, title = {Prediction of thermodynamic properties of oxygen in binary metallic solvents}, series = {Zeitschrift f{\"u}r Metallkunde}, volume = {74}, journal = {Zeitschrift f{\"u}r Metallkunde}, number = {6}, issn = {0044-3093}, pages = {372 -- 375}, year = {1983}, language = {en} } @article{AnikKapoorFrohberg1983, author = {Anik, Sabri and Kapoor, Madan Lal and Frohberg, Martin G.}, title = {Thermodynamic behaviour of oxygen in molten substitutional alloy solvents}, series = {Zeitschrift f{\"u}r Metallkunde}, volume = {74}, journal = {Zeitschrift f{\"u}r Metallkunde}, number = {1}, issn = {0044-3093}, pages = {53 -- 58}, year = {1983}, language = {en} } @article{AnikTopuzTuncel1992, author = {Anik, Sabri and Topuz, A. and Tuncel, H. S.}, title = {Einfluß der Parameter beim Diffusionsschweißen der St{\"a}hle X210Cr12 mit 25 CrMo4 auf die Ausbildung der Bindezone}, series = {Schweißen und Schneiden : Fachzeitschrift f{\"u}r Schweißen und verwandte Verfahren}, volume = {44}, journal = {Schweißen und Schneiden : Fachzeitschrift f{\"u}r Schweißen und verwandte Verfahren}, number = {2}, issn = {0036}, pages = {97 -- 100}, year = {1992}, language = {de} } @article{AnikTopuzTuncel1991, author = {Anik, Sabri and Topuz, A. and Tuncel, H. S.}, title = {Einfluß der Parameter beim Diffusionsschweißen der St{\"a}hle X 210 Cr 12 und 25 MoCr 4 auf ihre mechanischen Eigenschaften}, series = {Schweißen und Schneiden : Fachzeitschrift f{\"u}r Schweißen und verwandte Verfahren}, volume = {43}, journal = {Schweißen und Schneiden : Fachzeitschrift f{\"u}r Schweißen und verwandte Verfahren}, number = {6}, issn = {0036-7184}, pages = {341 -- 344}, year = {1991}, language = {de} } @article{AnikTuelbentci1973, author = {Anik, Sabri and Tuelbentci, K.}, title = {Lichtbogenschweißen : Untersuchung der Schweißschlacke und der Wirkungen auf das Entfernen der Schlacke beim Lichtbogenschweißen ; Teil 1}, series = {Technische Rundschau : TR ; das Schweizer Industrie-Magazin}, volume = {65}, journal = {Technische Rundschau : TR ; das Schweizer Industrie-Magazin}, number = {48}, publisher = {Medtrix Group}, address = {Basel}, issn = {0040-148X}, pages = {13 -- 15}, year = {1973}, language = {de} } @article{AnikTuelbentci1973, author = {Anik, Sabri and Tuelbentci, K.}, title = {Lichtbogenschweißen : Untersuchung der Schweißschlacke und der Wirkungen auf das Entfernen der Schlacke ; Teil 2}, series = {Technische Rundschau : TR ; das Schweizer Industrie-Magazin}, volume = {65}, journal = {Technische Rundschau : TR ; das Schweizer Industrie-Magazin}, number = {52}, publisher = {Medtrix Group}, address = {Basel}, issn = {0040-148X}, pages = {9 -- 13}, year = {1973}, language = {de} } @article{AnikTuelbentci1974, author = {Anik, Sabri and Tuelbentci, K.}, title = {Lichtbogenschweißen : Untersuchung der Schweißschlacke und der Wirkungen auf das Entfernen der Schlacke ; Teil 3}, series = {Technische Rundschau : TR ; das Schweizer Industrie-Magazin}, volume = {66}, journal = {Technische Rundschau : TR ; das Schweizer Industrie-Magazin}, number = {2}, publisher = {Medtrix Group}, address = {Basel}, issn = {0040-148X}, pages = {43 -- 47}, year = {1974}, language = {de} } @book{Baatz1993, author = {Baatz, Udo}, title = {CAD/CAM - Compass Maschinenbau. Ein Leitfaden f{\"u}r die optimale Systemauswahl CAD/CNC/CAM/CAE/PPS}, publisher = {CADIB}, address = {Aachen}, pages = {[getr. Z{\"a}hlung]}, year = {1993}, language = {de} } @book{Baatz1985, author = {Baatz, Udo}, title = {CAD/CAM im Maschinenbau - wohin geht der Weg?}, address = {M{\"u}lheim a.d. Ruhr}, year = {1985}, language = {de} } @book{Baatz1985, author = {Baatz, Udo}, title = {Nutzwertanalyse von CAD - Systemen der unteren und mittleren Preisklasse f{\"u}r dem Maschinenbau}, address = {M{\"u}lheim a.d. Ruhr}, year = {1985}, language = {de} } @article{Baatz1979, author = {Baatz, Udo}, title = {Neue Aspekte der Integrierten Qualit{\"a}tssicherung f{\"u}r Automobil - Zulieferer}, series = {Jahrbuch f{\"u}r Ingenieure}, journal = {Jahrbuch f{\"u}r Ingenieure}, publisher = {Expert-Verl.}, address = {Grafenau, Z{\"u}rich}, year = {1979}, language = {de} } @book{Baatz1973, author = {Baatz, Udo}, title = {Bildschirmunterst{\"u}tztes Konstruieren}, publisher = {VDI-Verl.}, address = {Duesseldorf}, isbn = {3-18-403039-3}, pages = {XI, 137 S. : Ill, graph. Darst.}, year = {1973}, language = {de} } @article{Baatz1972, author = {Baatz, Udo}, title = {Erstellung von Einzelteilzeichnungen mittels graphischer Datenverarbeitungsanlagen}, series = {Konstruktion}, volume = {24}, journal = {Konstruktion}, number = {9}, publisher = {VDI Fachmedien}, address = {D{\"u}sseldorf}, isbn = {0720-5953}, pages = {360 -- 369}, year = {1972}, language = {de} } @book{Baatz1971, author = {Baatz, Udo}, title = {Bildschirmunterst{\"u}tztes Konstruieren : Funktionsfindung, Prinziperarbeitung, Gestaltung und Detaillierung mit Hilfe graphischer Datenverarbeitungsanlagen}, address = {Aachen}, year = {1971}, language = {de} } @book{Baatz1981, author = {Baatz, Udo}, title = {Diplom-Ingenieur / Diplom-Ingenieurin an Fachhochschulen: Fachrichtung Maschinenbau : Stand: Dezember 1980}, publisher = {Bertelsmann}, address = {Bielefeld}, pages = {31 S., Beil.}, year = {1981}, language = {de} } @article{Baatz1972, author = {Baatz, Udo}, title = {Zukaufteile in Maschinenbauprodukten}, series = {ZWF Zeitschrift f{\"u}r wirtschaftliche Fertigung und Automatisierung}, volume = {67}, journal = {ZWF Zeitschrift f{\"u}r wirtschaftliche Fertigung und Automatisierung}, number = {6}, publisher = {Hanser}, address = {M{\"u}nchen}, isbn = {0044-3743}, doi = {10.1515/zwf-1972-670603}, pages = {301 -- 310}, year = {1972}, abstract = {Die technischen und wirtschaftlichen Anforderungen, die heutzutage an moderne Maschinen, Ger{\"a}te und Apparate gestellt werden, steigen st{\"a}ndig. Immer h{\"a}ufiger sehen sich die Konstrukteure gezwungen, geforderte Funktionen mit Hilfe zugekaufter Normeinzelteile, Bauelemente und Funktionsgruppen zu erf{\"u}llen. Bei dieser Entwicklung vergr{\"o}ßert sich die Zahl der von den Spezialherstellern angebotenen Zukaufteile {\"u}berproportional, in gleichem Maße geht dem Anwender die {\"U}bersicht {\"u}ber das Zukaufteilespektrum verloren. Zun{\"a}chst wird in diesem Bericht diese Entwicklung anhand einer im allgemeinen Maschinenbau durchgef{\"u}hrten Befragung aufgezeigt. Anschließend soll darauf aufbauend ein Ordnungssystem vorgestellt werden, welches jedem Unternehmen wieder eine {\"U}bersicht {\"u}ber das am Markt angebotene Zukaufteilespektrum erm{\"o}glicht.}, language = {de} } @article{Baatz1979, author = {Baatz, Udo}, title = {Wie erkennt man Rationalisierungsreserven im Konstruktionsbereich}, series = {Das Jahrbuch f{\"u}r Ingeneure 79 : aktuelles Wissen aus Forschung u. Praxis / Bartz, Wilfried J.; Wippler, Elmar}, journal = {Das Jahrbuch f{\"u}r Ingeneure 79 : aktuelles Wissen aus Forschung u. Praxis / Bartz, Wilfried J.; Wippler, Elmar}, publisher = {Expert-Verl.}, address = {Grafenau, W{\"u}rtt.}, isbn = {0171-3809}, pages = {263 -- 268}, year = {1979}, language = {de} } @article{Baatz1974, author = {Baatz, Udo}, title = {82.000 FL/h - Eine neue Dimension in der Abf{\"u}llung von Erfrischungsgetr{\"a}nken}, series = {Das Erfrischungsgetr{\"a}nk - Mineralwasser-Zeitung}, volume = {27}, journal = {Das Erfrischungsgetr{\"a}nk - Mineralwasser-Zeitung}, number = {14}, publisher = {Matthaes}, address = {Stuttgart}, isbn = {0342-2232}, pages = {341 -- 345}, year = {1974}, language = {de} } @article{Baatz1974, author = {Baatz, Udo}, title = {Flaschenbehandlung bei hohen Leistungen - Problemstellung und L{\"o}sungsm{\"o}glichkeiten}, series = {Das Erfrischungsgetr{\"a}nk - Mineralwasser-Zeitung}, volume = {27}, journal = {Das Erfrischungsgetr{\"a}nk - Mineralwasser-Zeitung}, number = {15}, publisher = {Matthaes}, address = {Stuttgart}, isbn = {0342-2232}, pages = {1175 -- 1178}, year = {1974}, language = {de} } @article{Baatz1974, author = {Baatz, Udo}, title = {Zur Problematik der Etikettenentfernung}, series = {Das Erfrischungsgetr{\"a}nk - Mineralwasser-Zeitung}, volume = {27}, journal = {Das Erfrischungsgetr{\"a}nk - Mineralwasser-Zeitung}, number = {39}, publisher = {Matthaes}, address = {Stuttgart}, isbn = {0342-2232}, pages = {926 -- 928}, year = {1974}, language = {de} } @article{BaatzButz1972, author = {Baatz, Udo and Butz, Hans-Werner}, title = {Rechnerunterstuetztes Konstruieren mit Symbolen}, series = {TZ f{\"u}r praktische Metallbearbeitung}, volume = {66}, journal = {TZ f{\"u}r praktische Metallbearbeitung}, number = {9}, publisher = {Grossmann}, address = {Stuttgart}, isbn = {0177-8900}, pages = {366 -- 370}, year = {1972}, language = {de} } @article{BaatzButzBaeck1972, author = {Baatz, Udo and Butz, Hans-Werner and B{\"a}ck, Karin}, title = {Aspekte der Bildschirmprogrammierung im Rahmen des rechnergest{\"u}tzten Konstruierens. Some aspects of CRT-screen programming in computer aided design.}, series = {eR - Elektronische Rechenanlagen}, volume = {14}, journal = {eR - Elektronische Rechenanlagen}, number = {5}, publisher = {Oldenbourg}, address = {M{\"u}nchen}, isbn = {0013-5720}, doi = {10.1524/itit.1972.14.16.229}, pages = {229 -- 235}, year = {1972}, abstract = {In den letzten Jahren hat der Einsatz von graphischen Datenverarbeitungsanlagen auf dem technischen, naturwissenschaftlichen und kommerziellen Sektor immer mehr an allgemeinem Interesse und Bedeutung gewonnen. Diese Entwicklung hat neue Aspekte und Probleme in bezug auf Anwendungsm{\"o}glichkeiten, Programmierung, Datenstrukturen sowie der Hard- und Software dieser Anlagen hervorgerufen. Zur Zeit werden von verschiedenen Institutionen die Einsatzm{\"o}glichkeiten graphischer Datenverarbeitungsanlagen in den Funktionsbereichen Konstruktion und Arbeitsvorbereitung untersucht. Der folgende Beitrag zeigt eine kurze {\"U}bersicht {\"u}ber die verschiedenen programmiertechnischen Probleme sowie eine Auswahl von Programmbeispielen, die am Laboratorium f{\"u}r Werkzeugmaschinen und Betriebslehre der RWTH Aachen entwickelt wurden. Bei den Bildschirmsystemen wird zwischen zwei Arten unterschieden. Aktive Bildschirmeinheiten besitzen als {\"a}ußeres Merkmal einen Lichtstift und eine Funktionstastatur zur Programmverzweigung. Passive Bildschirmeinheiten lassen demgegen{\"u}ber einen Eingriff in das Programm in der oben aufgef{\"u}hrten Form nicht zu. Zwischen diesen extremen Formen gibt es noch eine Reihe Mischformen. Die in Aachen zur Verf{\"u}gung stehende Anlage arbeitet aktiv und wird im nachfolgenden Kapitel n{\"a}her beschrieben.}, language = {de} } @article{BaatzKehrmann1981, author = {Baatz, Udo and Kehrmann, H.}, title = {Neue Produkte - per Zufall oder mit System?}, series = {Jahrbuch f{\"u}r F{\"u}hrungskr{\"a}fte}, journal = {Jahrbuch f{\"u}r F{\"u}hrungskr{\"a}fte}, publisher = {Expert-Verl.}, address = {Grafenau, Z{\"u}rich}, year = {1981}, language = {de} } @article{BaatzOpitzWiendahl1970, author = {Baatz, Udo and Opitz, Herwart and Wiendahl, Hans Peter}, title = {Bildschirmunterst{\"u}tztes Konstruieren - Prinziperarbeitung, Gestaltung und Detaillierung mit Hilfe der Men{\"u}technik}, series = {Industrieanzeiger}, volume = {92}, journal = {Industrieanzeiger}, number = {98}, publisher = {Konradin}, address = {Leinfelden-Echterdingen}, isbn = {0019-9036}, pages = {2371 -- 2374}, year = {1970}, language = {de} } @book{BaatzSanderLanghoff1996, author = {Baatz, Udo and Sander, Ralf and Langhoff, R.}, title = {Studienf{\"u}hrer f{\"u}r der Fachbereich 8 Maschinenbau FH Aachen}, publisher = {Stercken-Verl.}, address = {Aachen}, year = {1996}, language = {de} } @article{BaatzWiendahl1971, author = {Baatz, Udo and Wiendahl, Hans Peter}, title = {Methoden des Konstruierens - {\"U}bersicht {\"u}ber Ger{\"a}te, Methoden und Hilfsmittel zur Beseitigung des Engpasses Konstruktion, Teil 1}, series = {Grundlagen der Landtechnik}, volume = {21}, journal = {Grundlagen der Landtechnik}, number = {2}, publisher = {VDI-Verlag}, address = {D{\"u}sseldorf}, isbn = {0017-4920}, pages = {35 -- 38}, year = {1971}, abstract = {Der Konstruktionsbereich ist zu einem neuen Schwerpunkt der allgemeinen Rationalisierungsbem{\"u}hungen geworden. Zunehmend f{\"u}hrt man organisatorische Hilfsmittel, technische Hilfsmittel (EDVA) und neue Konstruktionsmethoden in der Konstruktion ein. Der vorliegende Beitrag analysiert zun{\"a}chst die Ursachen dieser Entwicklung und zeigt im weiteren einige heute bereits eingesetzte Hilfsmittel an Hand von Beispielen auf und diskutiert die Anwendungsm{\"o}glichkeiten.}, language = {de} } @article{BaatzWiendahl1971, author = {Baatz, Udo and Wiendahl, Hans Peter}, title = {Methoden des Konstruierens - {\"U}bersicht {\"u}ber Ger{\"a}te, Methoden und Hilfsmittel zur Beseitigung des Engpasses Konstruktion, Teil 2}, series = {Grundlagen der Landtechnik}, volume = {212}, journal = {Grundlagen der Landtechnik}, number = {3}, publisher = {VDI-Verlag}, address = {D{\"u}sseldorf}, isbn = {0017-4920}, pages = {77 -- 80}, year = {1971}, abstract = {Der Konstruktionsbereich ist zu einem neuen Schwerpunkt der allgemeinen Rationalisierungsbem{\"u}hungen geworden. Zunehmend f{\"u}hrt man organisatorische Hilfsmittel, technische Hilfsmittel (EDVA) und neue Konstruktionsmethoden in der Konstruktion ein. Der vorliegende Beitrag analysiert zun{\"a}chst die Ursachen dieser Entwicklung und zeigt im weiteren einige heute bereits eingesetzte Hilfsmittel an Hand von Beispielen auf und diskutiert die Anwendungsm{\"o}glichkeiten.}, language = {de} } @article{BabilonWilbringTappertetal.2018, author = {Babilon, Katharina and Wilbring, Daniela and Tappert, Tim and Pfaff, Raphael and Enning, Manfred}, title = {Schienenfahrzeugtechnik hands on - FH Aachen IMechE Railway Challenge}, series = {Ingenieurspiegel}, journal = {Ingenieurspiegel}, number = {2}, publisher = {Public Verlag}, address = {Bingen}, issn = {1868-5919}, pages = {20 -- 22}, year = {2018}, language = {de} } @inproceedings{BagheriSchleupenDahmannetal.2016, author = {Bagheri, Mohsen and Schleupen, Josef and Dahmann, Peter and Kallweit, Stephan}, title = {Kletternde Wartungsplattform f{\"u}r die wetterunabh{\"a}ngige Instandhaltung von Rotorbl{\"a}ttern an Windenergieanlagen - SMART}, series = {AKIDA 2016 Aachener Kolloquium f{\"u}r Instandhaltung, Diagnose und Anlagen{\"u}berwachung (AKIDA) am 15. und 16.11.2016, Technologiezentrum Aachen}, booktitle = {AKIDA 2016 Aachener Kolloquium f{\"u}r Instandhaltung, Diagnose und Anlagen{\"u}berwachung (AKIDA) am 15. und 16.11.2016, Technologiezentrum Aachen}, pages = {21 Folien}, year = {2016}, abstract = {In Deutschland liegt der Anteil der Windkraft an der Gesamtstromerzeugung bei 13,3\% mit mehr als 25.000 installierten Windenergieanlagen (WEA). Weltweit erf{\"a}hrt die Windbranche ein rasantes Wachstum. Indien und China berichten eine j{\"a}hrliche Wachstumsrate an Neuinstallationen von 45\%. Die Technologie zur Erzeugung elektrischer Energie aus Windkraft ist noch vergleichsweise jung. Durch die weltweit steigende Anzahl an Windenergieanlagen w{\"a}chst zunehmend der Bedarf an innovativen Wartungsl{\"o}sungen. Komponenten wie Generator oder Getriebe sind inzwischen weitestgehend ausgereift. Der Fokus richtet sich zunehmend auf die wesentliche Kernkomponente - die Rotorbl{\"a}tter. Industriekletterer inspizieren die Rotorbl{\"a}tter oder T{\"u}rme i.d.R. in einem zwei Jahres Rhythmus. Sie werden zunehmend durch Seilarbeitsb{\"u}hnen unterst{\"u}tzt. F{\"u}r gr{\"o}ßere Reparaturen kommen Kr{\"a}ne zum Einsatz, mit denen das Rotorblatt f{\"u}r die Instandhaltung demontiert wird. Die Standardinspektion besteht aus Sicht- und Klopfpr{\"u}fung der Rotorblattoberfl{\"a}che und ist nur bei sehr ruhiger Wetterlage durchf{\"u}hrbar. Seit September 2014 wird das Forschungsprojekt SMART (Scanning, Monitoring, Analysis, Repair and Transportation), Entwicklung einer Wartungsplattform f{\"u}r WEA, vom BMWi gef{\"o}rdert. Das Konsortium besteht aus zwei Firmen und der Fachhochschule Aachen. Die SMART-Anlage klettert reibschl{\"u}ssig am Turm der WEA mittels speziellen Kettenfahrwerken (Abbildung) auf- und abw{\"a}rts. Ein ringf{\"o}rmiges Spannsystems, basierend auf dem Konzept der „N{\"u}rnberger"-Schere, erzeugt die erforderliche Anpresskraft f{\"u}r den Kletterprozess. Wettergesch{\"u}tzte Arbeitskabinen erm{\"o}glichen die ganzj{\"a}hrige Instandhaltung von Rotorbl{\"a}ttern und ebenso T{\"u}rmen. Dadurch k{\"o}nnen Wartungsarbeiten auf 24 Stunden am Tag ausgeweitet werden. Der kombinierte Einsatz (Sensorfusion) bildgebender Messtechnik wie Thermografie, Ultraschall, und Terahertz in der Arbeitskabine kann die Dokumentation, Effizienz und Qualit{\"a}t der Instandhaltungsarbeiten erheblich verbessern. Langfristiges Ziel von SMART ist ein Condition Monitoring f{\"u}r Rotorbl{\"a}tter und T{\"u}rme auf Basis digitalisierter dreidimensionaler Volumenscans. Der kooperative Einsatz mit UAVs erweitert die Instandhaltungsstrategie. UAVs erm{\"o}glichen die schnelle, kosteng{\"u}nstige globale optische Inspektion von Rotorblattoberfl{\"a}chen zur Detektion potentieller Fehlstellen. Der „Proof-of-Concept" Meilenstein wurde mit der Demonstration eines funktionsf{\"a}higen Modells im Dezember 2015 erfolgreich abgeschlossen.}, language = {de} } @article{BarthWollert1998, author = {Barth, Heiko and Wollert, J{\"o}rg}, title = {SMARTes Konzept - von Produkt zur Fabrik}, series = {Facility-Management : Integration, Planung, Geb{\"a}udemanagement}, volume = {Bd. 4}, journal = {Facility-Management : Integration, Planung, Geb{\"a}udemanagement}, number = {H. August}, issn = {0948-0048}, pages = {30 -- 35}, year = {1998}, language = {de} } @article{BeckenbachScheidweiler2016, author = {Beckenbach, Isabel and Scheidweiler, Robert}, title = {Perfect ƒ-Matchings and ƒ-Factors in Hypergraphs - A Combinatorial Approach}, series = {Discrete Mathematics}, volume = {240}, journal = {Discrete Mathematics}, number = {10}, publisher = {Elsevier}, address = {Amsterdam}, issn = {2192-7782}, doi = {10.1016/j.disc.2017.05.005}, pages = {2499 -- 2506}, year = {2016}, abstract = {We prove characterizations of the existence of perfect ƒ-matchings in uniform mengerian and perfect hypergraphs. Moreover, we investigate the ƒ-factor problem in balanced hypergraphs. For uniform balanced hypergraphs we prove two existence theorems with purely combinatorial arguments, whereas for non-uniform balanced hypergraphs we show that the ƒ-factor problem is NP-hard.}, language = {en} } @inproceedings{BeerHaidnWillms1995, author = {Beer, Stefan and Haidn, O.J. and Willms, Herbert}, title = {Control of stoichiometric propellant supply in an H2/O2-spinning reserve system}, series = {Combustion technologies for a clean environment : selected papers from the proceedings of the first international conference, Vilamoura, Portugal, September 3 - 6, 1991. - (Energy, combustion and the environment ;1)}, booktitle = {Combustion technologies for a clean environment : selected papers from the proceedings of the first international conference, Vilamoura, Portugal, September 3 - 6, 1991. - (Energy, combustion and the environment ;1)}, editor = {Carvalho, Maria da Gra{\c{c}}a}, publisher = {Gordon and Breach}, address = {Basel [u.a.]}, isbn = {2-88124-619-2}, pages = {825 -- 838}, year = {1995}, language = {en} } @misc{Bellenberg2002, author = {Bellenberg, Markus}, title = {Optimierung einer Roboter-Schweißzelle als Basis eines E-Learning Systems}, year = {2002}, abstract = {Ziel war die technische {\"U}berarbeitung und Optimierung des vorliegenden Prototypen, um eine Basis f{\"u}r ein E-Learning System (Internet unterst{\"u}tztes Lernen) zu schaffen. Zu diesem Zweck wurde das Programm der Robotersteuerung neu erstellt, notwendige mechanische {\"A}nderungen an Roboterequipment und Materialf{\"o}rderung vorgenommen sowie eine neue Internet-Anbindung geschaffen. Wesentliche Ergebnisse der Arbeit sind: • Erzeugen roboterbasierter kreisinterpolierter Bahnschweißn{\"a}hte • Kommunikation des Lernsystems via Internet • Lernorientierte Steuerungssoftware}, subject = {Roboter}, language = {de} } @article{Benner1989, author = {Benner, Joachim}, title = {Schwingungsbelastung von drehzahlgeregelten Antrieben mit Stromrichtermotoren}, series = {Antriebstechnik : Konstruktion, Entwicklung und Anwendung von Antrieben und Steuerungen ; Organ der Forschungsvereinigung Antriebstechnik e.V.}, volume = {28}, journal = {Antriebstechnik : Konstruktion, Entwicklung und Anwendung von Antrieben und Steuerungen ; Organ der Forschungsvereinigung Antriebstechnik e.V.}, number = {12}, publisher = {Vereinigte Fachverl.}, address = {Mainz}, issn = {0341-2652}, pages = {49 -- 54}, year = {1989}, language = {de} } @inproceedings{Benner1989, author = {Benner, Joachim}, title = {Schwingungstechnische Dimensionierung von Maschinens{\"a}tzen mit Stromrichtermotoren}, series = {Antriebstechnisches Kolloquium '89 : Maschinen- und Anlagen{\"u}berwachung ; Elemente der Antriebstechnik im System ; neue Konzepte in der Antriebstechnik. - (Reihe IME-Leitfaden)}, booktitle = {Antriebstechnisches Kolloquium '89 : Maschinen- und Anlagen{\"u}berwachung ; Elemente der Antriebstechnik im System ; neue Konzepte in der Antriebstechnik. - (Reihe IME-Leitfaden)}, editor = {Peeken, Heinz}, publisher = {Verl. T{\"U}V Rheinland}, address = {K{\"o}ln}, issn = {3-88585-639-5}, pages = {309 -- 333}, year = {1989}, language = {de} } @techreport{Benner1982, author = {Benner, Joachim}, title = {Dynamisches Verhalten drehelastischer Kupplungen unter Ber{\"u}cksichtigung allgemeiner Materialgleichungen und Einbeziehung von Ausfallkriterien : Literaturrecherche; Berichtszeitraum 1981 - 1982. - (Forschungsheft / Forschungsvereinigung Antriebstechnik e.V. ; 132)}, publisher = {Forschungsvereinigung Antriebstechnik e.V.}, address = {Frankfurt/M.}, pages = {113 S. : zahlr. Ill.}, year = {1982}, language = {de} } @phdthesis{Benner1984, author = {Benner, Joachim}, title = {Experimentelle Untersuchungen des mechanischen Verhaltens drehnachgiebiger Wellenkupplungen und Entwicklung eines Ersatzmodells}, pages = {147 S. : graph. Darst.}, year = {1984}, language = {de} } @incollection{Benner2014, author = {Benner, Joachim}, title = {Berechnungsmethoden der W{\"a}lzlagerreibung und Einflussgr{\"o}ßen}, series = {SMK 2014 : Schweizer Maschinenelemente Kolloquim 25. und 26. November 2014}, booktitle = {SMK 2014 : Schweizer Maschinenelemente Kolloquim 25. und 26. November 2014}, publisher = {TUDpress Verl. der Wissenschaften}, address = {Dresden}, isbn = {978-3-944331-81-2}, pages = {151 -- 170}, year = {2014}, language = {de} } @techreport{BennerPlatt1986, author = {Benner, Joachim and Platt, Werner}, title = {Dynamisches Verhalten drehelastischer Kupplungen unter Ber{\"u}cksichtigung allgemeiner Materialgleichungen und Einbeziehung von Ausfallkriterien : Abschlußbericht; Berichtszeitraum 01. 07. 81 - 31. 05. 85. - (Forschungsheft / Forschungsvereinigung Antriebstechnik e.V. ; 221)}, publisher = {Forschungsvereinigung Antriebstechnik e.V.}, address = {Frankfurt/M.}, pages = {149 S. : zahlr. Ill.}, year = {1986}, language = {de} } @article{BergSchleserDelidovichetal.2018, author = {Berg, Alexander-Karl and Schleser, Markus and Delidovich, Artem and Houben, Alexander}, title = {Ultraschallunterst{\"u}tzter Schmelzklebstoffauftrag}, series = {adh{\"a}sion KLEBEN \& DICHTEN}, volume = {Volume 62}, journal = {adh{\"a}sion KLEBEN \& DICHTEN}, number = {Issue 12}, publisher = {Springer}, doi = {10.1007/s35145-018-0089-z}, pages = {32 -- 37}, year = {2018}, language = {de} } @techreport{BleckReisgenSchleseretal.2011, author = {Bleck, Wolfgang and Reisgen, Uwe and Schleser, Markus and Prahl, Ulrich and Mukherjee, Krishnendu and Abdurakhmanov, Aydemir}, title = {Konsistentes Materialmodell f{\"u}r Umwandlung und mechanische Eigenschaften beim Schweißen hochfester Mehrphasen-St{\"a}hle : IGF-Vorhaben 15548 N. (FAT-Schriftenreihe ; 234)}, publisher = {VDA}, address = {Berlin}, organization = {Forschungsvereinigung Automobiltechnik}, pages = {XVI, 17 - 174 S. Ill., graph. Darst.}, year = {2011}, language = {de} } @inproceedings{BraunChengDoweyetal.2020, author = {Braun, Sebastian and Cheng, Chi-Tsun and Dowey, Steve and Wollert, J{\"o}rg}, title = {Survey on Security Concepts to Adapt Flexible Manufacturing and Operations Management based upon Multi-Agent Systems}, series = {2020 IEEE 29th International Symposium on Industrial Electronics (ISIE)}, booktitle = {2020 IEEE 29th International Symposium on Industrial Electronics (ISIE)}, doi = {10.1109/ISIE45063.2020.9152210}, year = {2020}, language = {en} } @article{BraunChengDoweyetal.2021, author = {Braun, Sebastian and Cheng, Chi-Tsun and Dowey, Steve and Wollert, J{\"o}rg}, title = {Performance evaluation of skill-based order-assignment in production environments with multi-agent systems}, series = {IEEE Journal of Emerging and Selected Topics in Industrial Electronics}, journal = {IEEE Journal of Emerging and Selected Topics in Industrial Electronics}, number = {Early Access}, publisher = {IEEE}, address = {New York}, issn = {2687-9735}, doi = {10.1109/JESTIE.2021.3108524}, year = {2021}, abstract = {The fourth industrial revolution introduces disruptive technologies to production environments. One of these technologies are multi-agent systems (MASs), where agents virtualize machines. However, the agent's actual performances in production environments can hardly be estimated as most research has been focusing on isolated projects and specific scenarios. We address this gap by implementing a highly connected and configurable reference model with quantifiable key performance indicators (KPIs) for production scheduling and routing in single-piece workflows. Furthermore, we propose an algorithm to optimize the search of extrema in highly connected distributed systems. The benefits, limits, and drawbacks of MASs and their performances are evaluated extensively by event-based simulations against the introduced model, which acts as a benchmark. Even though the performance of the proposed MAS is, on average, slightly lower than the reference system, the increased flexibility allows it to find new solutions and deliver improved factory-planning outcomes. Our MAS shows an emerging behavior by using flexible production techniques to correct errors and compensate for bottlenecks. This increased flexibility offers substantial improvement potential. The general model in this paper allows the transfer of the results to estimate real systems or other models.}, language = {en} } @inproceedings{BraunChengLaietal.2019, author = {Braun, Sebastian and Cheng, Chi-Tsun and Lai, Chow Yin and Wollert, J{\"o}rg}, title = {Microservice Architecture for Automation - Realization by the example of a model-factory's manufacturing execution system}, series = {Proceedings of the 23rd World Multi-Conference on Systemics, Cybernetics and Informatics: WMSCI 2019}, booktitle = {Proceedings of the 23rd World Multi-Conference on Systemics, Cybernetics and Informatics: WMSCI 2019}, pages = {33 -- 37}, year = {2019}, language = {en} } @article{BucurLazarescuPopetal.2019, author = {Bucur, Alexandru and Lazarescu, Lucian and Pop, Grigore Marian and Achimas, Gheorghe and Gebhardt, Andreas}, title = {Tribological performance of biodegradable lubricants under different surface roughness of tools}, series = {Academic Journal of Manufacturing Engineering}, volume = {17}, journal = {Academic Journal of Manufacturing Engineering}, number = {1}, issn = {1583-7904}, pages = {172 -- 178}, year = {2019}, language = {en} } @inproceedings{BudaJozenfiniWollert2007, author = {Buda, Aurel and Jozenfini, B. and Wollert, J{\"o}rg}, title = {Mobile ad-hoc Network for home automation based on ZigBee application framework}, series = {1st European ZigBee Developer's Conference : June 18 - 20, 2007, Munich, Germany}, booktitle = {1st European ZigBee Developer's Conference : June 18 - 20, 2007, Munich, Germany}, publisher = {Design \& Elektronik}, address = {Poing}, organization = {European ZigBee Developer's Conference <1, 2007, M{\"u}nchen>}, pages = {1 -- 5}, year = {2007}, language = {en} } @inproceedings{BudaSchneiderWollert2009, author = {Buda, Aurel and Schneider, Ulf and Wollert, J{\"o}rg}, title = {Performanceanalyse von Frequenzdiversit{\"a}t in IEEE 802.15.4 Netzwerken}, series = {Wireless Technologies : 11. Kongress, 29. - 30. September 2009, Stuttgart; von der Technologie zur Anwendung / J{\"o}rg F. Wollert (Hrsg.) (Fortschritt-Berichte VDI : Reihe 10, Informatik, Kommunikation ; 800)}, booktitle = {Wireless Technologies : 11. Kongress, 29. - 30. September 2009, Stuttgart; von der Technologie zur Anwendung / J{\"o}rg F. Wollert (Hrsg.) (Fortschritt-Berichte VDI : Reihe 10, Informatik, Kommunikation ; 800)}, publisher = {VDI-Verl.}, address = {D{\"u}sseldorf}, isbn = {978-3-18-380010-0}, pages = {29 -- 38}, year = {2009}, language = {de} } @inproceedings{BudaSchuermannWollert2008, author = {Buda, Aurel and Sch{\"u}rmann, Volker and Wollert, J{\"o}rg}, title = {A middleware approach for industrial wireless automation networks}, series = {Proceedings of the Eighth IASTED International Conference on Wireless \& Optical Communications : May 26 - 28, 2008, Qu{\´e}bec City, Quebec, Canada}, booktitle = {Proceedings of the Eighth IASTED International Conference on Wireless \& Optical Communications : May 26 - 28, 2008, Qu{\´e}bec City, Quebec, Canada}, publisher = {Acta Pr.}, address = {Anaheim, Calif.}, organization = {International Association of Science and Technology for Development}, isbn = {978-0-88986-743-7}, pages = {76 -- 82}, year = {2008}, language = {de} } @inproceedings{BudaSchuermannWollert2009, author = {Buda, Aurel and Sch{\"u}rmann, Volker and Wollert, J{\"o}rg}, title = {Funktechnologien im 2,45 GHz ISM Frequenzband: {\"U}berblick und Coexistenzeigenschaften}, series = {Automation 2009 : Automatisierungskongress in Deutschland ; Kongress Baden-Baden, 16. und 17. Juni 2009. (VDI-Berichte ; 2067)}, booktitle = {Automation 2009 : Automatisierungskongress in Deutschland ; Kongress Baden-Baden, 16. und 17. Juni 2009. (VDI-Berichte ; 2067)}, publisher = {VDI-Verl.}, address = {D{\"u}sseldorf}, organization = {Automatisierungskongress <2009, Baden-Baden>}, isbn = {978-3-18-092067-2}, pages = {383 -- 386}, year = {2009}, language = {de} } @inproceedings{BudaSchuermannWollert2008, author = {Buda, Aurel and Sch{\"u}rmann, Volker and Wollert, J{\"o}rg}, title = {Automatische Generierung von Automatisierungsobjekten nach IEC 61131-3 zur einfachen Integration von Funkkomponenten in {\"u}bergeordnete Steuerungssysteme}, series = {Wireless automation : funkgest{\"u}tzte Kommunikation in der industriellen Automatisierungstechnik ; Tagung Berlin, 28. und 29. Februar 2008. (VDI-Berichte ; 2010)}, booktitle = {Wireless automation : funkgest{\"u}tzte Kommunikation in der industriellen Automatisierungstechnik ; Tagung Berlin, 28. und 29. Februar 2008. (VDI-Berichte ; 2010)}, publisher = {VDI-Verl.}, address = {D{\"u}sseldorf}, organization = {Verein Deutscher Ingenieure / Kompetenzfeld Informationstechnik}, isbn = {978-3-18-092010-8 ; 3-18-092010-8}, pages = {75 -- 84}, year = {2008}, language = {de} } @incollection{BudaSchuermannWollert2010, author = {Buda, Aurel and Sch{\"u}rmann, Volker and Wollert, J{\"o}rg}, title = {Wireless technologies in factory automation}, series = {Factory automation / ed. by Javier Silvestre-Blanes}, booktitle = {Factory automation / ed. by Javier Silvestre-Blanes}, publisher = {Intech}, address = {London}, isbn = {978-953-7619-42-8}, pages = {29 -- 50}, year = {2010}, language = {en} } @inproceedings{BudaVredalWollert2007, author = {Buda, Aurel and Vredal, Andreas and Wollert, J{\"o}rg}, title = {Einfache Integration von funkgest{\"u}tzten Kommunikationssystemen in der Automation}, series = {Wireless Technologies : 9. Kongress, 18. - 19. September 2007, Stuttgart ; von der Technologie zur Anwendung}, booktitle = {Wireless Technologies : 9. Kongress, 18. - 19. September 2007, Stuttgart ; von der Technologie zur Anwendung}, editor = {Wollert, J{\"o}rg}, publisher = {Aka}, address = {Berlin}, organization = {Wireless-Technologies-Kongress <9, 2007, Stuttgart>}, isbn = {978-3-89838-084-3}, pages = {189 -- 198}, year = {2007}, language = {de} } @inproceedings{BudaWollert2011, author = {Buda, Aurel and Wollert, J{\"o}rg}, title = {Leistungsbewertung von Ultra Wideband Funktechnologien nach ECMA 368 f{\"u}r den Einsatz in industriellen Kommunikationssystemen}, series = {Kommunikation in der Automation : Magdeburg, 27. - 28.09.2011 ; 2. Jahreskolloquium Kommunikation in der Automation ; KOMMA 2011 / Ulrich Jumar ... (Hrsg.)}, booktitle = {Kommunikation in der Automation : Magdeburg, 27. - 28.09.2011 ; 2. Jahreskolloquium Kommunikation in der Automation ; KOMMA 2011 / Ulrich Jumar ... (Hrsg.)}, publisher = {ifak, Institut f{\"u}r Automation und Kommunikation e.V. Magdeburg an der Otto-von-Guericke-Universit{\"a}t Magdeburg}, address = {Magdeburg}, organization = {Jahreskolloquium Kommunikation in der Automation <2, 2011, Magdeburg>}, isbn = {978-3-940961-58-7}, pages = {1 CD-ROM}, year = {2011}, language = {de} } @inproceedings{BudaWollert2008, author = {Buda, Aurel and Wollert, J{\"o}rg}, title = {Kompensation von Fading und Koexistenzproblemen in IEEE 802.15.4 Netzwerken durch Diversit{\"a}t : die Kombination macht's m{\"o}glich}, series = {Automation 2008: L{\"o}sungen f{\"u}r die Zukunft ; der Automatisierungskongress in Deutschland ; Tagung Baden-Baden, 3. und 4. Juni 2008. (VDI-Berichte ; 2032)}, booktitle = {Automation 2008: L{\"o}sungen f{\"u}r die Zukunft ; der Automatisierungskongress in Deutschland ; Tagung Baden-Baden, 3. und 4. Juni 2008. (VDI-Berichte ; 2032)}, publisher = {VDI-Verl.}, address = {D{\"u}sseldorf}, organization = {Automatisierungskongress <2008, Baden-Baden>}, isbn = {978-3-18-092032-0}, pages = {139 -- 142}, year = {2008}, language = {de} } @inproceedings{BudaWollertVedral2009, author = {Buda, Aurel and Wollert, J{\"o}rg and Vedral, Andreas}, title = {UWIfac - Ultra wideband interface for factory automation}, series = {Automation 2009 : Automatisierungskongress in Deutschland ; Kongress Baden-Baden, 16. und 17. Juni 2009. (VDI-Berichte ; 2067)}, booktitle = {Automation 2009 : Automatisierungskongress in Deutschland ; Kongress Baden-Baden, 16. und 17. Juni 2009. (VDI-Berichte ; 2067)}, publisher = {VDI-Verl.}, address = {D{\"u}sseldorf}, organization = {Automatisierungskongress <2009, Baden-Baden>}, isbn = {978-3-18-092067-2}, pages = {257 -- 260}, year = {2009}, language = {de} } @inproceedings{BuschkuehleSchuermannWollert2009, author = {Buschk{\"u}hle, Peter and Sch{\"u}rmann, Volker and Wollert, J{\"o}rg}, title = {Abstraction of wireless communication by a convergence middleware in conjunction with a XML-configuration}, series = {Information technology and electrical engineering : devices and systems, materials and technologies for the future ; Ilmenau 07 - 10 September 2009 ; 54. IWK Internationales Wissenschaftliches Kolloquium}, booktitle = {Information technology and electrical engineering : devices and systems, materials and technologies for the future ; Ilmenau 07 - 10 September 2009 ; 54. IWK Internationales Wissenschaftliches Kolloquium}, publisher = {Techn. Univ.}, address = {Ilmenau}, isbn = {978-3-938843-44-4}, pages = {95 -- 96}, year = {2009}, language = {en} } @inproceedings{BueckingPfaffDirksmeier2018, author = {B{\"u}cking, Henrik and Pfaff, Raphael and Dirksmeier, Roger}, title = {Sensor positioning and thermal model for condition monitoring of pressure gas reservoirs in vehicles}, series = {Proceedings of the Fourth European Conference of the Prognostics and Health Management Society, Utrecht, Netherlands, 2018}, booktitle = {Proceedings of the Fourth European Conference of the Prognostics and Health Management Society, Utrecht, Netherlands, 2018}, pages = {5 Seiten}, year = {2018}, language = {en} } @inproceedings{ChavezBermudezCruzCastanonRuchayetal.2022, author = {Chavez Bermudez, Victor Francisco and Cruz Castanon, Victor Fernando and Ruchay, Marco and Wollert, J{\"o}rg}, title = {Rapid prototyping framework for automation applications based on IO-Link}, series = {Tagungsband AALE 2022}, booktitle = {Tagungsband AALE 2022}, editor = {Leipzig, Hochschule f{\"u}r Technik, Wirtschaft und Kultur}, address = {Leipzig}, isbn = {978-3-910103-00-9}, doi = {10.33968/2022.28}, pages = {8 Seiten}, year = {2022}, abstract = {The development of protype applications with sensors and actuators in the automation industry requires tools that are independent of manufacturer, and are flexible enough to be modified or extended for any specific requirements. Currently, developing prototypes with industrial sensors and actuators is not straightforward. First of all, the exchange of information depends on the industrial protocol that these devices have. Second, a specific configuration and installation is done based on the hardware that is used, such as automation controllers or industrial gateways. This means that the development for a specific industrial protocol, highly depends on the hardware and the software that vendors provide. In this work we propose a rapid-prototyping framework based on Arduino to solve this problem. For this project we have focused to work with the IO-Link protocol. The framework consists of an Arduino shield that acts as the physical layer, and a software that implements the IO-Link Master protocol. The main advantage of such framework is that an application with industrial devices can be rapid-prototyped with ease as its vendor independent, open-source and can be ported easily to other Arduino compatible boards. In comparison, a typical approach requires proprietary hardware, is not easy to port to another system and is closed-source.}, language = {en} } @inproceedings{ChavezBermudezWollert2022, author = {Chavez Bermudez, Victor Francisco and Wollert, J{\"o}rg}, title = {10BASE-T1L industry 4.0 smart switch for field devices based on IO-Link}, series = {2022 IEEE 18th International Conference on Factory Communication Systems (WFCS)}, booktitle = {2022 IEEE 18th International Conference on Factory Communication Systems (WFCS)}, publisher = {IEEE}, isbn = {978-1-6654-1086-1}, doi = {10.1109/WFCS53837.2022.9779176}, pages = {4 Seiten}, year = {2022}, abstract = {The recent amendment to the Ethernet physical layer known as the IEEE 802.3cg specification, allows to connect devices up to a distance of one kilometer and delivers a maximum of 60 watts of power over a twisted pair of wires. This new standard, also known as 10BASE-TIL, promises to overcome the limits of current physical layers used for field devices and bring them a step closer to Ethernet-based applications. The main advantage of 10BASE- TIL is that it can deliver power and data over the same line over a long distance, where traditional solutions (e.g., CAN, IO-Link, HART) fall short and cannot match its 10 Mbps bandwidth. Due to its recentness, IOBASE- TIL is still not integrated into field devices and it has been less than two years since silicon manufacturers released the first Ethernet-PHY chips. In this paper, we present a design proposal on how field devices could be integrated into a IOBASE-TIL smart switch that allows plug-and-play connectivity for sensors and actuators and is compliant with the Industry 4.0 vision. Instead of presenting a new field-level protocol for this work, we have decided to adopt the IO-Link specification which already includes a plug-and-play approach with features such as diagnosis and device configuration. The main objective of this work is to explore how field devices could be integrated into 10BASE-TIL Ethernet, its adaption with a well-known protocol, and its integration with Industry 4.0 technologies.}, language = {en} } @inproceedings{ChavezBermudezWollert2019, author = {Chavez Bermudez, Victor Francisco and Wollert, J{\"o}rg}, title = {Gateway for Automation Controllers and Cloud based Voice Recognition Services}, series = {KommA, 10. Jahreskolloquium Kommunikation in der Automation}, booktitle = {KommA, 10. Jahreskolloquium Kommunikation in der Automation}, publisher = {Institut f{\"u}r Automation und Kommunikation}, address = {Magdeburg}, organization = {KommA, 2019, Jahreskolloquium Kommunikation in der Automation, 10., Lemgo, DE, 2019-11-20 - 2019-11-21}, isbn = {978-3-944722-85-6}, pages = {1 -- 8}, year = {2019}, language = {en} } @inproceedings{ChavezBermudezWollert2020, author = {Chavez Bermudez, Victor Francisco and Wollert, J{\"o}rg}, title = {Arduino based Framework for Rapid Application Development of a Generic IO-Link interface}, series = {Kommunikation und Bildverarbeitung in der Automation}, booktitle = {Kommunikation und Bildverarbeitung in der Automation}, publisher = {Springer Vieweg}, address = {Berlin}, isbn = {978-3-662-59895-5}, doi = {10.1007/978-3-662-59895-5_2}, pages = {21 -- 33}, year = {2020}, abstract = {The implementation of IO-Link in the automation industry has increased over the years. Its main advantage is it offers a digital point-to-point plugand-play interface for any type of device or application. This simplifies the communication between devices and increases productivity with its different features like self-parametrization and maintenance. However, its complete potential is not always used. The aim of this paper is to create an Arduino based framework for the development of generic IO-Link devices and increase its implementation for rapid prototyping. By generating the IO device description file (IODD) from a graphical user interface, and further customizable options for the device application, the end-user can intuitively develop generic IO-Link devices. The peculiarity of this framework relies on its simplicity and abstraction which allows to implement any sensor functionality and virtually connect any type of device to an IO-Link master. This work consists of the general overview of the framework, the technical background of its development and a proof of concept which demonstrates the workflow for its implementation.}, language = {en} } @article{ChengWollertChenetal.2023, author = {Cheng, Chi-Tsun and Wollert, J{\"o}rg and Chen, Xi and Fapojuwo, Abraham O.}, title = {Guest Editorial : Circuits and Systems for Industry X.0 Applications}, series = {IEEE Journal on Emerging and Selected Topics in Circuits and Systems}, volume = {13}, journal = {IEEE Journal on Emerging and Selected Topics in Circuits and Systems}, edition = {2}, publisher = {IEEE}, address = {New York}, issn = {2156-3357 (Print)}, doi = {10.1109/JETCAS.2023.3278843}, pages = {457 -- 460}, year = {2023}, language = {en} } @inproceedings{ChudobaKonradSchleseretal.2009, author = {Chudoba, Rostislav and Konrad, Martin and Schleser, Markus and Meskouris, Konstantin and Reisgen, Uwe}, title = {Parametric study of tensile response of TRC specimens reinforced with epoxy-penetrated multi-filament yarns}, series = {Textilbeton - Theorie und Praxis : Tagungsband zum 4. Kolloquium zu textilbewehrten Tragwerken (CTRS4) und zur 1. Anwendertagung, Dresden, 3.6.2009 - 5.6.2009}, booktitle = {Textilbeton - Theorie und Praxis : Tagungsband zum 4. Kolloquium zu textilbewehrten Tragwerken (CTRS4) und zur 1. Anwendertagung, Dresden, 3.6.2009 - 5.6.2009}, editor = {Curbach, Manfred}, publisher = {Techn. Univ.}, address = {Dresden}, isbn = {978-3-86780-122-5}, pages = {87 -- 98}, year = {2009}, language = {en} } @incollection{ChwallekGoelzerReichert2018, author = {Chwallek, Constanze and G{\"o}lzer, Kaan and Reichert, Walter}, title = {Faymonville - Wachstum als Komplexit{\"a}tstreiber}, series = {Fallstudienkompendium Hidden Champions - Innovationen f{\"u}r den Weltmarkt}, booktitle = {Fallstudienkompendium Hidden Champions - Innovationen f{\"u}r den Weltmarkt}, publisher = {Springer Gabler}, isbn = {978-3-658-17829-1}, doi = {10.1007/978-3-658-17829-1_18}, pages = {299 -- 312}, year = {2018}, abstract = {Die Fallstudie FAYMONVILLE besch{\"a}ftigt sich damit, wie es dem Familienunternehmen Faymonville aus Ostbelgien gelungen ist, sich zu einem der f{\"u}hrenden Hersteller in seiner Branche zu entwickeln. Die gezielte Identifizierung neuer M{\"a}rkte, die Fokussierung auf die relevanten Kundenbed{\"u}rfnisse und eine konsistente Produktpolitik mit einem abgestimmten Fertigungskonzept legen die Grundsteine f{\"u}r den Erfolg. Das vorliegende Fallbeispiel zeigt anschaulich, wie es gelingen kann, den prinzipiellen Widerspruch zwischen wirtschaftlicher und kundenindividueller Fertigung erfolgreich aufzul{\"o}sen.}, language = {de} } @incollection{Cordewiner2013, author = {Cordewiner, Hans-Josef}, title = {Konstruktion im Wandel: von der technischen Zeichnung zum 3D-Produktmodell}, series = {Innovation durch Kooperation : wie der Mittelstand durch Zusammenarbeit mit den Hochschulen seine Wettbewerbsf{\"a}higkeit steigert : Festschrift f{\"u}r Prof. Dr. rer. nat. Johannes Gartzen / Thomas Gartzen, Ute Gartzen (Hrsg.)}, booktitle = {Innovation durch Kooperation : wie der Mittelstand durch Zusammenarbeit mit den Hochschulen seine Wettbewerbsf{\"a}higkeit steigert : Festschrift f{\"u}r Prof. Dr. rer. nat. Johannes Gartzen / Thomas Gartzen, Ute Gartzen (Hrsg.)}, publisher = {Apprimus Verlag}, address = {Aachen}, isbn = {978--3-86359-136-6}, pages = {115 -- 121}, year = {2013}, language = {de} } @article{CosmaKesslerGebhardtetal.2020, author = {Cosma, Cosmin and Kessler, Julia and Gebhardt, Andreas and Campbell, Ian and Balc, Nicolae}, title = {Improving the Mechanical Strength of Dental Applications and Lattice Structures SLM Processed}, series = {Materials}, volume = {13}, journal = {Materials}, number = {4}, publisher = {MDPI}, address = {Basel}, issn = {1996-1944}, doi = {10.3390/ma13040905}, pages = {1 -- 18}, year = {2020}, abstract = {To manufacture custom medical parts or scaffolds with reduced defects and high mechanical characteristics, new research on optimizing the selective laser melting (SLM) parameters are needed. In this work, a biocompatible powder, 316L stainless steel, is characterized to understand the particle size, distribution, shape and flowability. Examination revealed that the 316L particles are smooth, nearly spherical, their mean diameter is 39.09 μm and just 10\% of them hold a diameter less than 21.18 μm. SLM parameters under consideration include laser power up to 200 W, 250-1500 mm/s scanning speed, 80 μm hatch spacing, 35 μm layer thickness and a preheated platform. The effect of these on processability is evaluated. More than 100 samples are SLM-manufactured with different process parameters. The tensile results show that is possible to raise the ultimate tensile strength up to 840 MPa, adapting the SLM parameters for a stable processability, avoiding the technological defects caused by residual stress. Correlating with other recent studies on SLM technology, the tensile strength is 20\% improved. To validate the SLM parameters and conditions established, complex bioengineering applications such as dental bridges and macro-porous grafts are SLM-processed, demonstrating the potential to manufacture medical products with increased mechanical resistance made of 316L.}, language = {en} } @inproceedings{DannenSchindelePruemmeretal.2022, author = {Dannen, Tammo and Schindele, Benedikt and Pr{\"u}mmer, Marcel and Arntz, Kristian and Bergs, Thomas}, title = {Methodology for the self-optimizing determination of additive manufacturing process eligibility and optimization potentials in toolmaking}, series = {Procedia CIRP}, volume = {107}, booktitle = {Procedia CIRP}, publisher = {Elsevier}, address = {Amsterdam}, issn = {2212-8271}, doi = {10.1016/j.procir.2022.05.188}, pages = {1539 -- 1544}, year = {2022}, abstract = {Additive Manufacturing (AM) of metallic workpieces faces a continuously rising technological relevance and market size. Producing complex or highly strained unique workpieces is a significant field of application, making AM highly relevant for tool components. Its successful economic application requires systematic workpiece based decisions and optimizations. Considering geometric and technological requirements as well as the necessary post-processing makes deciding effortful and requires in-depth knowledge. As design is usually adjusted to established manufacturing, associated technological and strategic potentials are often neglected. To embed AM in a future proof industrial environment, software-based self-learning tools are necessary. Integrated into production planning, they enable companies to unlock the potentials of AM efficiently. This paper presents an appropriate methodology for the analysis of process-specific AM-eligibility and optimization potential, added up by concrete optimization proposals. For an integrated workpiece characterization, proven methods are enlarged by tooling-specific figures. The first stage of the approach specifies the model's initialization. A learning set of tooling components is described using the developed key figure system. Based on this, a set of applicable rules for workpiece-specific result determination is generated through clustering and expert evaluation. Within the following application stage, strategic orientation is quantified and workpieces of interest are described using the developed key figures. Subsequently, the retrieved information is used for automatically generating specific recommendations relying on the generated ruleset of stage one. Finally, actual experiences regarding the recommendations are gathered within stage three. Statistic learning transfers those to the generated ruleset leading to a continuously deepening knowledge base. This process enables a steady improvement in output quality.}, language = {en} } @inproceedings{DilgerMundDiltheyetal.2003, author = {Dilger, Klaus and Mund, Frank and Dilthey, Ulrich and Schleser, Markus and Raupach, Michael and Walk-Lauffer, Bernd}, title = {Einsatz einer polymeren Phase zur Verbundverbesserung}, series = {Textile reinforced structures : proceedings of the 2nd Colloquium on Textile Reinforced Structures (CTRS2), Dresden, Germany, 29.9. - 1.10.2003}, booktitle = {Textile reinforced structures : proceedings of the 2nd Colloquium on Textile Reinforced Structures (CTRS2), Dresden, Germany, 29.9. - 1.10.2003}, editor = {Curbach, Manfred}, publisher = {Techn. Univ.}, address = {Dresden}, organization = {Colloquium on Textile Reinforced Structures <2, 2003, Dresden>}, isbn = {3-86005-386-8}, pages = {133 -- 144}, year = {2003}, language = {de} } @article{DiltheyBrandenburgSchleser2004, author = {Dilthey, Ulrich and Brandenburg, Annette and Schleser, Markus}, title = {Dispensing and application of unfilled adhesives in the micro range}, series = {Welding and cutting. 3 (2004), H. 4}, journal = {Welding and cutting. 3 (2004), H. 4}, issn = {1612-3433}, pages = {250 -- 254}, year = {2004}, language = {en} } @incollection{DiltheyBrandenburgSchleser2005, author = {Dilthey, Ulrich and Brandenburg, Annette and Schleser, Markus}, title = {Mikrokleben}, series = {Montage hybrider Mikrosysteme : Handhabungs- und F{\"u}getechniken f{\"u}r die Klein- und Mittelserienfertigung}, booktitle = {Montage hybrider Mikrosysteme : Handhabungs- und F{\"u}getechniken f{\"u}r die Klein- und Mittelserienfertigung}, publisher = {Springer}, address = {Berlin [u.a.]}, isbn = {978-3-540-23706-8}, pages = {161 -- 172}, year = {2005}, language = {de} } @inproceedings{DiltheyMundRaupachetal.2004, author = {Dilthey, Ulrich and Mund, F. and Raupach, Michael and Schleser, Markus and Walk-Lauffer, Bernd}, title = {Improvement of textile reinforced concrete by polymer additives}, series = {ICPIC '04 : 11th International Congress on Polymers in Concrete : 2nd-4th June, 2004 at BAM, Berlin, Germany : proceedings / ed. by M. Maultzsch}, booktitle = {ICPIC '04 : 11th International Congress on Polymers in Concrete : 2nd-4th June, 2004 at BAM, Berlin, Germany : proceedings / ed. by M. Maultzsch}, publisher = {BAM}, address = {Berlin}, isbn = {3-00-013706-8}, pages = {469 -- 476}, year = {2004}, language = {en} } @inproceedings{DiltheySchleser2006, author = {Dilthey, Ulrich and Schleser, Markus}, title = {Composite improvement of textile reinforced concrete by polymeric impregnation of the textiles}, series = {International Symposium Polymers in Concrete : proceedings of ISPIC 2006, 2-4 April 2006 - University of Minho - Guimar{\~a}es, Portugal}, booktitle = {International Symposium Polymers in Concrete : proceedings of ISPIC 2006, 2-4 April 2006 - University of Minho - Guimar{\~a}es, Portugal}, editor = {Barroso de Aguiar, Jose and Jalali, Said and Camoes, Aires and Ferrera, Rui Miguel}, publisher = {Universidade do Minho, Departamento de Engenharia Civil}, address = {Guimar{\~a}es}, organization = {International Symposium in Concrete <2006, Guimar{\~a}es)}, isbn = {972-99179-1-4}, pages = {185 -- 192}, year = {2006}, language = {en} } @inproceedings{DiltheySchleserChudobaetal.2007, author = {Dilthey, Ulrich and Schleser, Markus and Chudoba, Rostislav and Konrad, Martin}, title = {Experimental investigation and micro-mechanical simulaltion of concrete reinforced with epoxy impregnated fabrics}, series = {Fibre-reinforced polymer reinforcement for concrete structures : proceedings of the 8th international conference : Patras, Greece, July 16- 18, 2007}, booktitle = {Fibre-reinforced polymer reinforcement for concrete structures : proceedings of the 8th international conference : Patras, Greece, July 16- 18, 2007}, editor = {Triantafillou, T. C.}, publisher = {Univ.}, address = {Patras}, organization = {International Symposium on Fibre-Reinforced Polymer Reinforcement for Concrete Structures <8, 2007, Patras>}, isbn = {9608969107}, pages = {456 -- 457}, year = {2007}, language = {en} } @article{DiltheySchleserFeldmannetal.2008, author = {Dilthey, Ulrich and Schleser, Markus and Feldmann, Martin and Pak, Daniel and Geßler, Achim}, title = {Investigation of punctiform, plane and hybrid joints of textile-reinforced concrete parts}, series = {Cement and concrete composites}, volume = {Vol. 30}, journal = {Cement and concrete composites}, number = {iss. 2}, issn = {0958-9465}, pages = {82 -- 87}, year = {2008}, language = {en} } @article{DiltheySchleserGessleretal.2005, author = {Dilthey, Ulrich and Schleser, Markus and Geßler, Achim and Rettweiler, Timo and V{\"o}lling, Boris}, title = {Kleben textilbewehrter Betonbauteile}, series = {Schweissen und Schneiden : Fachzeitschrift f{\"u}r Schweißen und verwandte Verfahren. Jg. 57 (2005), Nr. 8}, journal = {Schweissen und Schneiden : Fachzeitschrift f{\"u}r Schweißen und verwandte Verfahren. Jg. 57 (2005), Nr. 8}, issn = {0036-7184}, pages = {373 -- 377}, year = {2005}, language = {de} } @article{DiltheySchleserHanischetal.2006, author = {Dilthey, Ulrich and Schleser, Markus and Hanisch, Vera and Gries, Thomas}, title = {Garnzugpr{\"u}fung polymergetr{\"a}nkter Textilien f{\"u}r die Bewehrung von Beton}, series = {Technische Textilien}, volume = {49}, journal = {Technische Textilien}, number = {1}, issn = {0323-3243}, pages = {48 -- 50}, year = {2006}, language = {de} }