@article{HoetterFateriGebhardt2012,
  author    = {H{\"o}tter, Jan-Steffen and Fateri, Miranda and Gebhardt, Andreas},
  title     = {Prozessoptimierung des SLM-Prozesses mit hoch-reflektiven und thermisch sehr gut leitenden Materialien durch systematische Parameterfindung und begleitende Simulationen am Beispiel von Silber},
  series = {RTejournal - Forum f{\"u}r Rapid Technologie},
  volume    = {9},
  journal   = {RTejournal - Forum f{\"u}r Rapid Technologie},
  number    = {1},
  publisher = {Fachhoschule Aachen},
  address   = {Aachen},
  issn      = {1614-0923},
  url       = {http://nbn-resolving.de/urn:nbn:de:0009-2-33639},
  pages     = {1 -- 14},
  year      = {2012},
  abstract  = {Additive Manufacturing durch Aufschmelzen von Metallpulvern hat sich auf breiter Front als Herstellverfahren, auch f{\"u}r Endprodukte, etabliert. Besonders f{\"u}r die Variante des Selective Laser Melting (SLM) sind Anwendungen in der Zahntechnik bereits weit verbreitet und der Einsatz in sensitiven Branchen wie der Luftfahrt ist in greifbare N{\"a}he ger{\"u}ckt. Deshalb werden auch vermehrt Anstrengungen unternommen, um bisher nicht verarbeitete Materialien zu qualifizieren. Dies sind vorzugsweise Nicht-Eisen- und Edelmetalle, die sowohl eine sehr hohe Reflektivit{\"a}t als auch eine sehr gute W{\"a}rmeleitf{\"a}higkeit aufweisen - beides Eigenschaften, die die Beherrschung des Laser-Schmelzprozesses erschweren und nur kleine Prozessfenster zulassen. Die Arbeitsgruppe SLM des Lehr- und Forschungsgebietes Hochleistungsverfahren der Fertigungstechnik hat sich unter der Randbedingung einer kleinen und mit geringer Laserleistung ausgestatteten SLM Maschine der Aufgabe gewidmet und am Beispiel von Silber die Parameterfelder f{\"u}r Einzelspuren und wenig komplexe Geometrien systematisch untersucht. Die Arbeiten wurden von FEM Simulationen begleitet und durch metallographische Untersuchungen verifiziert. Die Ergebnisse bilden die Grundlage zur schnellen Parameterfindung bei komplexen Geometrien und bei Ver{\"a}nderungen der Zusammensetzung, wie sie bei zuk{\"u}nftigen Legierungen zu erwarten sind. Die Ergebnisse werden exemplarisch auf unterschiedliche Geometrien angewandt und entsprechende Bauteile gezeigt.},
  language  = {de}
}
@article{Starke1984,
  author    = {Starke, G{\"u}nther},
  title     = {Prozesssteuerung und Automatisierung in der Schweisstechnik},
  pages     = {341 -- 351},
  year      = {1984},
  language  = {de}
}
@article{Starke1998,
  author    = {Starke, G{\"u}nther},
  title     = {Prozeßkontrolle und Prozeßsteuerung f{\"u}r die Fertigung in schweißtechnischen Betrieben},
  pages     = {45 -- 52},
  year      = {1998},
  language  = {de}
}
@article{RaffeisAdjeiKyeremehVroomenetal.2020,
  author    = {Raffeis, Iris and Adjei-Kyeremeh, Frank and Vroomen, Uwe and Westhoff, Elmar and Bremen, Sebastian and Hohoi, Alexandru and B{\"u}hrig-Polaczek, Andreas},
  title     = {Qualification of a Ni-Cu alloy for the laser powder bed fusion process (LPBF): Its microstructure and mechanical properties},
  series = {Applied Sciences},
  volume    = {10},
  journal   = {Applied Sciences},
  number    = {Art. 3401},
  publisher = {MDPI},
  address   = {Basel},
  issn      = {2076-3417},
  doi       = {10.3390/app10103401},
  pages     = {1 -- 15},
  year      = {2020},
  abstract  = {As researchers continue to seek the expansion of the material base for additive manufacturing, there is a need to focus attention on the Ni-Cu group of alloys which conventionally has wide industrial applications. In this work, the G-NiCu30Nb casting alloy, a variant of the Monel family of alloys with Nb and high Si content is, for the first time, processed via the laser powder bed fusion process (LPBF). Being novel to the LPBF processes, optimum LPBF parameters were determined, and hardness and tensile tests were performed in as-built conditions and after heat treatment at 1000 °C. Microstructures of the as-cast and the as-built condition were compared. Highly dense samples (99.8\% density) were achieved after varying hatch distance (80 µm and 140 µm) with scanning speed (550 mm/s-1500 mm/s). There was no significant difference in microhardness between varied hatch distance print sets. Microhardness of the as-built condition (247 HV0.2) exceeded the as-cast microhardness (179 HV0.2.). Tensile specimens built in vertical (V) and horizontal (H) orientations revealed degrees of anisotropy and were superior to conventionally reported figures. Post heat treatment increased ductility from 20\% to 31\% (V), as well as from 16\% to 25\% (H), while ultimate tensile strength (UTS) and yield strength (YS) were considerably reduced.},
  language  = {en}
}
@article{StarkeDrews1983,
  author    = {Starke, G{\"u}nther and Drews, P.},
  title     = {Qualitaetssicherung in der automatisierten schweisstechnischen Fertigung durch Einsatz von Sensoren},
  series = {Sensor. 6 (1983)},
  journal   = {Sensor. 6 (1983)},
  pages     = {29 -- 45},
  year      = {1983},
  language  = {de}
}
@article{StarkeDrews1983,
  author    = {Starke, G{\"u}nther and Drews, P.},
  title     = {Qualitaetssicherung in der automatisierten schweisstechnischen Fertigung durch Einsatz von Sensoren},
  series = {Technisches Messen tm. 50 (1983), H. 12},
  journal   = {Technisches Messen tm. 50 (1983), H. 12},
  isbn      = {0171-8096},
  pages     = {467 -- 473},
  year      = {1983},
  language  = {de}
}
@article{KunkelGebhardtMpofuetal.2019,
  author    = {Kunkel, Maximilian Hugo and Gebhardt, Andreas and Mpofu, Khumbulani and Kallweit, Stephan},
  title     = {Quality assurance in metal powder bed fusion via deep-learning-based image classification},
  series = {Rapid Prototyping Journal},
  volume    = {26},
  journal   = {Rapid Prototyping Journal},
  number    = {2},
  issn      = {1355-2546},
  doi       = {10.1108/RPJ-03-2019-0066},
  pages     = {259 -- 266},
  year      = {2019},
  language  = {en}
}
@article{FranzenPindersPfaffetal.2018,
  author    = {Franzen, Julius and Pinders, Erik and Pfaff, Raphael and Enning, Manfred},
  title     = {RailCrowd's virtual fleets: Make most of your asset data},
  series = {Deine Bahn},
  journal   = {Deine Bahn},
  number    = {9},
  publisher = {Bahn-Fachverlag},
  address   = {Berlin},
  issn      = {0948-7263},
  pages     = {11 -- 13},
  year      = {2018},
  abstract  = {For smaller railway operators or those with a diverse fleet, it can be difficult to collect sufficient data to improve maintenance programs. At the same time, new rules such as entity in charge of maintenance - ECM - regulations impose an additional workload by requiring a dedicated maintenance management system and specific reports. The RailCrowd platform sets out to facilitate compliance with ECM and similar regulations while at the same time pooling anonymised fleet data across operators to form virtual fleets, providing greater data insights.},
  language  = {en}
}
@article{Gebhardt2004,
  author    = {Gebhardt, Andreas},
  title     = {Rapid Prototyping},
  series = {Landolt-B{\"o}rnstein - Group VIII Advanced Materials and Technologies‡Vol. 1 Laser Physics and Applications‡Subvol. C Laser Applications / authors: B{\"a}uerle, D. ...},
  journal   = {Landolt-B{\"o}rnstein - Group VIII Advanced Materials and Technologies‡Vol. 1 Laser Physics and Applications‡Subvol. C Laser Applications / authors: B{\"a}uerle, D. ...},
  publisher = {Heidelberg},
  address   = {Springer},
  isbn      = {3-540-00105-0},
  pages     = {105 -- 123},
  year      = {2004},
  language  = {en}
}
@article{Gebhardt1996,
  author    = {Gebhardt, Andreas},
  title     = {Rapid Prototyping - Laser-gest{\"u}tzte Revolution der Produktentwicklung. Teil I},
  series = {Laser Magazin (1996)},
  journal   = {Laser Magazin (1996)},
  isbn      = {0945-8875},
  pages     = {6 -- 9},
  year      = {1996},
  language  = {de}
}
@article{Gebhardt2003,
  author    = {Gebhardt, Andreas},
  title     = {Rapid Prototyping : Grundlagen, Verfahren und Einsatzkriterien f{\"u}r die industrielle Praxis},
  series = {Konstruieren mit Kunststoffen. - 3. Aufl.},
  journal   = {Konstruieren mit Kunststoffen. - 3. Aufl.},
  publisher = {Springer -VDI-Verl.},
  address   = {D{\"u}sseldorf},
  isbn      = {3-935065-13-2},
  year      = {2003},
  language  = {de}
}
@article{Gebhardt2001,
  author    = {Gebhardt, Andreas},
  title     = {Rapid Prototyping and PIV},
  year      = {2001},
  language  = {en}
}
@article{GebhardtSchmachtenberg1996,
  author    = {Gebhardt, Andreas and Schmachtenberg, E.},
  title     = {Rapid Prototyping und Tooling},
  pages     = {1 -- 20},
  year      = {1996},
  language  = {de}
}
@article{Gebhardt1998,
  author    = {Gebhardt, Andreas},
  title     = {Rapid Tooling. Der schnelle Weg zum Spritzgießwerkzeug.},
  series = {Kunststoffe, M{\"u}nchen. 88 (1998), H. 11},
  journal   = {Kunststoffe, M{\"u}nchen. 88 (1998), H. 11},
  isbn      = {0023-5563},
  pages     = {1992 -- 2000},
  year      = {1998},
  language  = {de}
}
@article{Grundmann2004,
  author    = {Grundmann, Reinhard},
  title     = {Raumlufttechnik, L{\"u}ftungstechnik, Klimatechnik, L{\"a}rm},
  series = {HLH - Zeitschrift f{\"u}r Heizung, L{\"u}ftung, Klimatechnik, Haustechnik. 55 (2004), H. 12},
  journal   = {HLH - Zeitschrift f{\"u}r Heizung, L{\"u}ftung, Klimatechnik, Haustechnik. 55 (2004), H. 12},
  isbn      = {0017-9906},
  pages     = {46 -- 49},
  year      = {2004},
  language  = {de}
}
@article{LeidingerNoistenWollert2012,
  author    = {Leidinger, Rafael and Noisten, Thomas and Wollert, J{\"o}rg},
  title     = {Realtime automation networks in moVing industrial environments},
  series = {Journal of systemics, cybernetics and informatics},
  volume    = {Vol. 10},
  journal   = {Journal of systemics, cybernetics and informatics},
  number    = {Iss. 2},
  publisher = {IIIC},
  address   = {Orlando},
  issn      = {1690-4532},
  pages     = {52 -- 56},
  year      = {2012},
  abstract  = {The radio-based wireless data communication has made the realization of new technical solutions possible in many fields of the automation technology (AT). For about ten years, a constant disproportionate growth of wireless technologies can be observed in the automation technology. However, it shows that especially for the AT, conventional technologies of office automation are unsuitable and/or not manageable. The employment of mobile services in the industrial automation technology has the potential of significant cost and time savings. This leads to an increased productivity in various fields of the AT, for example in the factory and process automation or in production logistics. In this paper technologies and solutions for an automation-suited supply of mobile wireless services will be introduced under the criteria of real time suitability, IT-security and service orientation. Emphasis will be put on the investigation and development of wireless convergence layers for different radio technologies, on the central provision of support services for an easy-to-use, central, backup enabled management of combined wired / wireless networks and on the study on integrability in a Profinet real-time Ethernet network.},
  language  = {en}
}
@article{StarkeKremerWasmuth1999,
  author    = {Starke, G{\"u}nther and Kremer-Wasmuth, S.},
  title     = {Rechnergest{\"u}tzte Prozeßkontrolle und -dokumentation zur Qualit{\"a}ts{\"u}berwachung beim Schweißen},
  series = {Qualit{\"a}tsorientierte Schweißtechnik als Wettbewerbsfaktor, DVS-Berichte. 196 (1999)},
  journal   = {Qualit{\"a}tsorientierte Schweißtechnik als Wettbewerbsfaktor, DVS-Berichte. 196 (1999)},
  isbn      = {0418-9639},
  pages     = {49 -- 52},
  year      = {1999},
  language  = {de}
}
@article{HeinrichsWeck1977,
  author    = {Heinrichs, Horst and Weck, M.},
  title     = {Rechnerunterstuetzte Aufbereitung von Finite-Elemente-Rechenmodellen -Erstellen der FEM-Netzwerke},
  series = {Industrieanzeiger. 99 (1977), H. 102},
  journal   = {Industrieanzeiger. 99 (1977), H. 102},
  pages     = {2059 -- 2061},
  year      = {1977},
  language  = {de}
}
@article{HeinrichsWeckHeimann1977,
  author    = {Heinrichs, Horst and Weck, M. and Heimann, A.},
  title     = {Rechnerunterstuetzte Aufbereitung von Finite-Elemente-Rechenmodellen-Erfassung der Bauteilgeometrie},
  series = {Industrieanzeiger. 99 (1977), H. 78},
  journal   = {Industrieanzeiger. 99 (1977), H. 78},
  pages     = {1509 -- 1512},
  year      = {1977},
  language  = {de}
}
@article{BaatzButz1972,
  author    = {Baatz, Udo and Butz, Hans-Werner},
  title     = {Rechnerunterstuetztes Konstruieren mit Symbolen},
  series = {TZ f{\"u}r praktische Metallbearbeitung},
  volume    = {66},
  journal   = {TZ f{\"u}r praktische Metallbearbeitung},
  number    = {9},
  publisher = {Grossmann},
  address   = {Stuttgart},
  isbn      = {0177-8900},
  pages     = {366 -- 370},
  year      = {1972},
  language  = {de}
}
@article{WillmsBeer1992,
  author    = {Willms, Herbert and Beer, Stefan},
  title     = {Regelung eines H(IND 2)/O(IND 2)-Dampferzeugers},
  isbn      = {0939-2963},
  year      = {1992},
  language  = {de}
}
@article{Willms1993,
  author    = {Willms, Herbert},
  title     = {Regelung eines H2/O2-Dampferzeugers mit Hilfe eines modifizierten Zirkondioxid-Sensors},
  series = {Chemie Ingenieur Technik},
  volume    = {65},
  journal   = {Chemie Ingenieur Technik},
  number    = {8},
  publisher = {Wiley-VCH},
  address   = {Weinheim},
  isbn      = {0009-286X},
  pages     = {954 -- 956},
  year      = {1993},
  language  = {de}
}
@article{WillmsBeerFroehlkeetal.1993,
  author    = {Willms, Herbert and Beer, Stefan and Fr{\"o}hlke, K. and Haidn, O.J. and [u.a.],},
  title     = {Regelung eines Wasserstoff-/Sauerstoff-Dampferzeugers mit Hilfe eines modifizierten Zirkondioxid-Sensors},
  year      = {1993},
  language  = {de}
}
@article{KaemperPappasHopster1990,
  author    = {K{\"a}mper, Klaus-Peter and Pappas, D. P. and Hopster, H.},
  title     = {Reversible transition between perpendicular and in-plane magnetization in ultrathin films. Pappas, D. P.; K{\"a}mper, K.-P.; Hopster, H.},
  series = {Physical Review Letters. 64 (1990), H. 26},
  journal   = {Physical Review Letters. 64 (1990), H. 26},
  isbn      = {1079-7114},
  pages     = {3179 -- 3182},
  year      = {1990},
  language  = {en}
}
@article{MichauxMatternKallweit2018,
  author    = {Michaux, F. and Mattern, P. and Kallweit, Stephan},
  title     = {RoboPIV: how robotics enable PIV on a large industrial scale},
  series = {Measurement Science and Technology},
  volume    = {29},
  journal   = {Measurement Science and Technology},
  number    = {7},
  publisher = {IOP},
  address   = {Bristol},
  issn      = {1361-6501},
  doi       = {10.1088/1361-6501/aab5c1},
  pages     = {074009},
  year      = {2018},
  abstract  = {This work demonstrates how the interaction between particle image velocimetry (PIV) and robotics can massively increase measurement efficiency. The interdisciplinary approach is shown using the complex example of an automated, large scale, industrial environment: a typical automotive wind tunnel application. Both the high degree of flexibility in choosing the measurement region and the complete automation of stereo PIV measurements are presented. The setup consists of a combination of three robots, individually used as a 6D traversing unit for the laser illumination system as well as for each of the two cameras. Synchronised movements in the same reference frame are realised through a master-slave setup with a single interface to the user. By integrating the interface into the standard wind tunnel management system, a single measurement plane or a predefined sequence of several planes can be requested through a single trigger event, providing the resulting vector fields within minutes. In this paper, a brief overview on the demands of large scale industrial PIV and the existing solutions is given. Afterwards, the concept of RoboPIV is introduced as a new approach. In a first step, the usability of a selection of commercially available robot arms is analysed. The challenges of pose uncertainty and importance of absolute accuracy are demonstrated through comparative measurements, explaining the individual pros and cons of the analysed systems. Subsequently, the advantage of integrating RoboPIV directly into the existing wind tunnel management system is shown on basis of a typical measurement sequence. In a final step, a practical measurement procedure, including post-processing, is given by using real data and results. Ultimately, the benefits of high automation are demonstrated, leading to a drastic reduction in necessary measurement time compared to non-automated systems, thus massively increasing the efficiency of PIV measurements.},
  language  = {en}
}
@article{StarkeAhlbehrendtBischoffetal.2009,
  author    = {Starke, G{\"u}nther and Ahlbehrendt, Norbert and Bischoff, Rainer and Melzer, Harald and Sieber, Sven and Senk, Burkhard and Kramarczyk, Peter},
  title     = {RoboTOOL. Technologien f{\"u}r den ortsflexiblen Einsatz von Robotern bei tempor{\"a}ren Arbeitsaufgaben in der Fertigung},
  series = {wt Werkstattstechnik online},
  volume    = {Bd. 99},
  journal   = {wt Werkstattstechnik online},
  number    = {H. 9},
  issn      = {1436-4980},
  pages     = {661 -- 670},
  year      = {2009},
  language  = {de}
}
@article{BabilonWilbringTappertetal.2018,
  author    = {Babilon, Katharina and Wilbring, Daniela and Tappert, Tim and Pfaff, Raphael and Enning, Manfred},
  title     = {Schienenfahrzeugtechnik hands on - FH Aachen IMechE Railway Challenge},
  series = {Ingenieurspiegel},
  journal   = {Ingenieurspiegel},
  number    = {2},
  publisher = {Public Verlag},
  address   = {Bingen},
  issn      = {1868-5919},
  pages     = {20 -- 22},
  year      = {2018},
  language  = {de}
}
@article{Wollert1999,
  author    = {Wollert, J{\"o}rg},
  title     = {Schlaue Produktion von smarten Autos : hinter der Smart-Produktion steckt ein innovatives Logistikkonzept},
  series = {Technica},
  volume    = {Bd. 48},
  journal   = {Technica},
  number    = {H. 4},
  issn      = {0040-866X},
  pages     = {20 -- 23},
  year      = {1999},
  language  = {de}
}
@article{Gebhardt1999,
  author    = {Gebhardt, Andreas},
  title     = {Schnell und flexibel zur Kleinserie. Effizienzsteigerung bei der Realisierung von Komponenten und Teilsystemen},
  series = {Ingenieur-Werkstoffe. 8 (1999), H. 3},
  journal   = {Ingenieur-Werkstoffe. 8 (1999), H. 3},
  isbn      = {0935-5715},
  pages     = {8 -- 14},
  year      = {1999},
  language  = {de}
}
@article{GebhardtGuntermannHaeming1997,
  author    = {Gebhardt, Andreas and Guntermann, P. and H{\"a}ming, L.},
  title     = {Schweißen mit dem Nd:YAG-Laser},
  series = {Der Praktiker, Schweißen und Schneiden. 49 (1997), H. 4},
  journal   = {Der Praktiker, Schweißen und Schneiden. 49 (1997), H. 4},
  isbn      = {0554-9965},
  pages     = {170 -- 172},
  year      = {1997},
  language  = {de}
}
@article{StarkeStrunzSpiess1995,
  author    = {Starke, G{\"u}nther and Strunz, U. and Spieß, C.},
  title     = {Schweißprozeßparameteroptimierung mit Fuzzy-Logik},
  series = {Schweißen und Schneiden. 47 (1995), H. 6},
  journal   = {Schweißen und Schneiden. 47 (1995), H. 6},
  isbn      = {0036-7184},
  pages     = {494 -- 503},
  year      = {1995},
  language  = {de}
}
@article{Benner1989,
  author    = {Benner, Joachim},
  title     = {Schwingungsbelastung von drehzahlgeregelten Antrieben mit Stromrichtermotoren},
  series = {Antriebstechnik : Konstruktion, Entwicklung und Anwendung von Antrieben und Steuerungen ; Organ der Forschungsvereinigung Antriebstechnik e.V.},
  volume    = {28},
  journal   = {Antriebstechnik : Konstruktion, Entwicklung und Anwendung von Antrieben und Steuerungen ; Organ der Forschungsvereinigung Antriebstechnik e.V.},
  number    = {12},
  publisher = {Vereinigte Fachverl.},
  address   = {Mainz},
  issn      = {0341-2652},
  pages     = {49 -- 54},
  year      = {1989},
  language  = {de}
}
@article{EnningDollsBrunberg2009,
  author    = {Enning, Manfred and Dolls, S. and Brunberg, A.},
  title     = {Selbsteinstellverfahren f{\"u}r Temperiervorrichtungen mit Außenverrohrung / Dolls, S. ; Enning, M. ; Brunberg, A. ; Abel, D.},
  series = {Automation 2009 : Automatisierungskongress in Deutschland ; Kongress Baden-Baden, 16. und 17. Juni 2009 / VDI-VDE-Gesellschaft Mess- und Automatisierungstechnik},
  journal   = {Automation 2009 : Automatisierungskongress in Deutschland ; Kongress Baden-Baden, 16. und 17. Juni 2009 / VDI-VDE-Gesellschaft Mess- und Automatisierungstechnik},
  publisher = {VDI-Verl.},
  address   = {D{\"u}sseldorf},
  isbn      = {978-3-18-092067-2},
  pages     = {429 -- 432},
  year      = {2009},
  language  = {de}
}
@article{HoetterFateriGebhardt2012,
  author    = {H{\"o}tter, Jan-Steffen and Fateri, Miranda and Gebhardt, Andreas},
  title     = {Selective laser melting of metals: desktop machines open up new chances even for small companies},
  series = {Advanced materials research},
  volume    = {622-623},
  journal   = {Advanced materials research},
  publisher = {Trans Tech Publ.},
  address   = {Baech},
  issn      = {1662-8985 (E-Journal); 1022-6680 (Print)},
  doi       = {10.4028/www.scientific.net/AMR.622-623.461},
  pages     = {461 -- 465},
  year      = {2012},
  abstract  = {Additive manufacturing (AM) of metal parts by using Selective Laser Melting (SLM) has become a powerful tool mostly in the area of automotive, aerospace engineering and others. Especially in the field of dentistry, jewelry and related branches that require individualized or even one-of-a-kind products, the direct digital manufacturing process opens up new ways of design and manufacturing. In these fields, mostly small and medium sized businesses (SME) are operating which do not have sufficient human and economic resources to invest in this technology. But to stay competitive, the application of AM can be regarded as a necessity. In this situation a new desktop machine (Realizer SLM 50) was introduced that cost about 1/3 of a shop floor SLM machine and promises small quality parts. To find out whether the machine really is an alternative for SMEs the University of Applied Science, Aachen, Germany, designed, build and optimized typical parts from the dentistry and the jewelry branches using CoCr and silver material, the latter being new with this application. The paper describes the SLM procedure and how to find and optimize the most important parameters. The test is accompanied by digital simulation in order to verify the build parameters and to plan future builds. The procedure is shown as well as the resulting parts made from CoCr and silver material.},
  language  = {en}
}
@article{FateriGebhardt2015,
  author    = {Fateri, Miranda and Gebhardt, Andreas},
  title     = {Selective Laser Melting of Soda-Lime Glass Powder},
  series = {International Journal of Applied Ceramic Technology},
  volume    = {12},
  journal   = {International Journal of Applied Ceramic Technology},
  number    = {1},
  publisher = {Wiley-Blackwell},
  address   = {Oxford},
  issn      = {1744-7402},
  doi       = {10.1111/ijac.12338},
  pages     = {53 -- 61},
  year      = {2015},
  language  = {en}
}
@article{RieperGebhardtStucker2016,
  author    = {Rieper, Harald and Gebhardt, Andreas and Stucker, Brent},
  title     = {Selective Laser Melting of the Eutectic Silver-Copper Alloy Ag 28 wt \% Cu},
  series = {RTejournal - Forum f{\"u}r Rapid Technologie},
  volume    = {13},
  journal   = {RTejournal - Forum f{\"u}r Rapid Technologie},
  issn      = {1614-0923},
  url       = {http://nbn-resolving.de/nbn:de:0009-2-44141},
  year      = {2016},
  abstract  = {The aim of this work was to perform a detailed investigation of the use of Selective Laser Melting (SLM) technology to process eutectic silver-copper alloy Ag 28 wt. \% Cu (also called AgCu28). The processing occurred with a Realizer SLM 50 desktop machine. The powder analysis (SEM-topography, EDX, particle distribution) was reported as well as the absorption rates for the near-infrared (NIR) spectrum. Microscope imaging showed the surface topography of the manufactured parts. Furthermore, microsections were conducted for the analysis of porosity. The Design of Experiments approach used the response surface method in order to model the statistical relationship between laser power, spot distance and pulse time.},
  language  = {en}
}
@article{Starke1986,
  author    = {Starke, G{\"u}nther},
  title     = {Sensoren fuer Schutzgasschweissroboter: Problemstellung, Funktionsweise, Handhabung und Programmierung von praxiserprobten Systemen},
  pages     = {1 -- 22},
  year      = {1986},
  language  = {de}
}
@article{StarkeBeckmannRogosetal.1987,
  author    = {Starke, G{\"u}nther and Beckmann, L.-H. and Rogos, J. and Schmall, K-H. (u.a.)},
  title     = {Sensoren in der automatisierten Schweisstechnik},
  pages     = {61 -- 147},
  year      = {1987},
  language  = {de}
}
@article{StarkeDrews1985,
  author    = {Starke, G{\"u}nther and Drews, P.},
  title     = {Sensoren in der Schweisstechnik},
  series = {Die Umschau. 84 (1985), H. 5},
  journal   = {Die Umschau. 84 (1985), H. 5},
  isbn      = {0041-6347},
  pages     = {296 -- 300},
  year      = {1985},
  language  = {de}
}
@article{StarkeDrews1992,
  author    = {Starke, G{\"u}nther and Drews, P.},
  title     = {Sensorik f{\"u}r das Schutzgasschweißen mit Robotern},
  series = {DVS-Berichte. 143 (1992)},
  journal   = {DVS-Berichte. 143 (1992)},
  isbn      = {0418-9639},
  pages     = {62 -- 66},
  year      = {1992},
  language  = {de}
}
@article{GebhardtMatharPlumetal.1996,
  author    = {Gebhardt, Andreas and Mathar, W. and Plum, H-D. and Wolf, M.},
  title     = {Serienqualit{\"a}t und -st{\"u}ckzahlen durch Abformprozesse},
  pages     = {147 -- 159},
  year      = {1996},
  language  = {de}
}
@article{KaemperBergBegemannetal.1998,
  author    = {K{\"a}mper, Klaus-Peter and Berg, U. and Begemann, M. and Hagemann, B. (u.a.)},
  title     = {Series production and testing of a micro motor. Serienfertigung und Pr{\"u}fung eines Mikromotors},
  series = {Actuator 98 : 6th International Conference on New Actuators ; 17 - 19 June, 1998, Bremen, Germany ; conference proceedings / ed.: Hubert Borgmann ...},
  journal   = {Actuator 98 : 6th International Conference on New Actuators ; 17 - 19 June, 1998, Bremen, Germany ; conference proceedings / ed.: Hubert Borgmann ...},
  publisher = {Messe Bremen},
  address   = {Bremen},
  isbn      = {3-933339-00-6},
  pages     = {552 -- 555},
  year      = {1998},
  language  = {en}
}
@article{GebhardtMatharPlum1994,
  author    = {Gebhardt, Andreas and Mathar, W. and Plum, H.-D.},
  title     = {SFM-System Stereolithographie und selektives Lasersintern im Vergleich},
  pages     = {85 -- 95},
  year      = {1994},
  language  = {de}
}
@article{ReisgenSchleserMokrovetal.2010,
  author    = {Reisgen, Uwe and Schleser, Markus and Mokrov, Oleg and Ahmed, Essam},
  title     = {Shielding gas influences on laser weldability of tailored blanks of advanced automotive steels},
  series = {Applied surface science},
  volume    = {257},
  journal   = {Applied surface science},
  number    = {5},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0169-4332 (E-Journal); 0169-4332 (Print)},
  doi       = {10.1016/j.apsusc.2010.08.042},
  pages     = {1401 -- 1406},
  year      = {2010},
  abstract  = {The effects of shielding gas types and flow rates on CO2 laser weldability of DP600/TRIP700 steel sheets were studied in this work. The evaluated shielding gases were helium (He), argon (Ar) and different mixtures of He and Ar. Weld penetration, tensile strength and formability (Erichsen test) of laser welds were found to be strongly dependent upon the shielding gas types. The ability of shielding gas in removing plasma plume and thus increasing weld penetration is believed to be closely related to ionization potential and atomic weight which determine the period of plasma formation and disappearance. It was found that the higher helium shielding gas flow rate, the deeper weld penetration and the lower weld width.},
  language  = {en}
}
@article{KaemperDoepperEhrfeldetal.1995,
  author    = {K{\"a}mper, Klaus-Peter and D{\"o}pper, J. and Ehrfeld, W. and Hagemann, B.},
  title     = {Simulation supported design of LIGA Microsystems. K{\"a}mper, K.-P.; D{\"o}pper, J.; Ehrfeld, W.; Hagemann, B.; Hill, S.D.J.; Lehr, H.},
  series = {Simulation and design of microsystems and microstructures : [... contains the papers presented at the First International Conference on the Simulation and Design of Microsystems and Microstructures, MicroSIM '95, which was held in Southampton, UK, in September 1995] / [organised by: Wessex Institute of Technology, UK]. Ed.: R. A. Adey},
  journal   = {Simulation and design of microsystems and microstructures : [... contains the papers presented at the First International Conference on the Simulation and Design of Microsystems and Microstructures, MicroSIM '95, which was held in Southampton, UK, in September 1995] / [organised by: Wessex Institute of Technology, UK]. Ed.: R. A. Adey},
  publisher = {Computational Mechanics Publ.},
  address   = {Southampton [u.a.]},
  isbn      = {1-85312-390-0},
  pages     = {3 -- 10},
  year      = {1995},
  language  = {en}
}
@article{Knepper1996,
  author    = {Knepper, Ludger},
  title     = {Simulation: Vom reinen Planungswerkzeug zum Betriebsf{\"u}hrungs-Instrument},
  series = {Foerdern und Heben. 46 (1996), H. 3},
  journal   = {Foerdern und Heben. 46 (1996), H. 3},
  isbn      = {0341-2636},
  pages     = {158 -- 160},
  year      = {1996},
  language  = {de}
}
@article{StarkeZackFriedrichetal.2003,
  author    = {Starke, G{\"u}nther and Zack, Y. and Friedrich, A.-P. and Drichel, E.},
  title     = {Simulationswerkzeug bei der Herstellung von mikroelektronischen Komponenten. Schnelles Beurteilen von Alternativen in der Produktionsplanung und im Fertigungsdesign},
  series = {FB/IE - Zeitschrift f{\"u}r Unternehmensentwicklung und Industrial Engineering. 52 (2003), H. 5},
  journal   = {FB/IE - Zeitschrift f{\"u}r Unternehmensentwicklung und Industrial Engineering. 52 (2003), H. 5},
  isbn      = {1431-2271},
  pages     = {204 -- 212},
  year      = {2003},
  language  = {de}
}
@article{BarthWollert1998,
  author    = {Barth, Heiko and Wollert, J{\"o}rg},
  title     = {SMARTes Konzept - von Produkt zur Fabrik},
  series = {Facility-Management : Integration, Planung, Geb{\"a}udemanagement},
  volume    = {Bd. 4},
  journal   = {Facility-Management : Integration, Planung, Geb{\"a}udemanagement},
  number    = {H. August},
  issn      = {0948-0048},
  pages     = {30 -- 35},
  year      = {1998},
  language  = {de}
}
@article{Wollert2005,
  author    = {Wollert, J{\"o}rg},
  title     = {Softwaretrends in der Automatisierungstechnik},
  series = {Etz : Elektrotechnik \& Automation ; Organ des VDE Verband der Elektrotechnik Elektronik Informationstechnik e.V. und der Energietechnischen Gesellschaft im VDE (ETG) und der VDI/VDE-Gesellschaft Mess- und Automatisierungstechnik (GMA)},
  volume    = {126},
  journal   = {Etz : Elektrotechnik \& Automation ; Organ des VDE Verband der Elektrotechnik Elektronik Informationstechnik e.V. und der Energietechnischen Gesellschaft im VDE (ETG) und der VDI/VDE-Gesellschaft Mess- und Automatisierungstechnik (GMA)},
  number    = {S2},
  issn      = {0948-7387},
  pages     = {74 -- 79},
  year      = {2005},
  language  = {de}
}
@article{KallweitDuesSiekmann1994,
  author    = {Kallweit, Stephan and Dues, M. W. and Siekmann, H. E.},
  title     = {Spectral Analysis of Pressure Fluctuations and Velocity Fields as Investigated on Propeller Pumps / Dues, M. W. ; Kallweit, S. D. ; Siekmann, H. E.},
  series = {Preprints : Fifth International Symposium on Transport Phenomena and Dynamics of Rotating Machinery (ISROMAC-5) : May 8 - 11, 1994, Maui Marriott Hotel, Kaanapali, Maui, Hawaii, U.S.A / sponsored by Pacific Center of Thermal-Fluids Engineering. [W.-J. Yang, chairman] / Vol. B.},
  journal   = {Preprints : Fifth International Symposium on Transport Phenomena and Dynamics of Rotating Machinery (ISROMAC-5) : May 8 - 11, 1994, Maui Marriott Hotel, Kaanapali, Maui, Hawaii, U.S.A / sponsored by Pacific Center of Thermal-Fluids Engineering. [W.-J. Yang, chairman] / Vol. B.},
  pages     = {98 -- 112},
  year      = {1994},
  language  = {en}
}