@article{ReisgenSchleserAbdurakhmanovetal.2012,
  author    = {Reisgen, Uwe and Schleser, Markus and Abdurakhmanov, Aydemir and Gumenyuk, Andrey},
  title     = {Measuring of plasma properties induced by non-vacuum electron beam welding},
  series = {Physics of plasma},
  volume    = {19},
  journal   = {Physics of plasma},
  number    = {1},
  publisher = {AIP Publishing},
  address   = {Melville, NY},
  issn      = {1089-7674 (E-Journal); 1070-664X (Print)},
  doi       = {10.1063/1.3675874},
  pages     = {1 -- 7},
  year      = {2012},
  abstract  = {Electron beam plasma measurement was realised by means of DIABEAM system invented by ISF RWTH Aachen. The Langmuir probe method is used for measurement. The relative simplicity of the method and the possibility of dispersion of high power on the probe allow its application for the investigation of high-power electron beams. The key element of the method is a rotating thin tungsten wire, which intersects the beam transversely on its axis and collects part of the current by itself. The signals, which are registered in the DIABEAM as a voltage, were taken in the form of amplitude. The conversion of the probe current into the distribution along the beam radius was realised using the Abel's method. A voltage-current characteristic was built for the beam current. The local electron density as well as the electron temperature, the floating potential and the plasma potential were measured and calculated by means of this characteristic.},
  language  = {en}
}
@article{ReisgenSchleserMokrovetal.2012,
  author    = {Reisgen, Uwe and Schleser, Markus and Mokrov, Oleg and Zabirov, Alexander and F{\"u}ssel, Uwe and Schnick, Michael and Hertel, Martin and Jaeckel, Sebastian},
  title     = {Modellierung und Visualisierung der MSG-Lichtbogenprozesse},
  series = {Schweissen und Schneiden : Fachzeitschrift f{\"u}r Schweißen und verwandte Verfahren},
  volume    = {64},
  journal   = {Schweissen und Schneiden : Fachzeitschrift f{\"u}r Schweißen und verwandte Verfahren},
  number    = {4},
  publisher = {DVS Verlag},
  address   = {D{\"u}sseldorf},
  issn      = {0036-7184},
  pages     = {166 -- 174},
  year      = {2012},
  language  = {de}
}
@article{ScheikSchleserReisgen2012,
  author    = {Scheik, Sven and Schleser, Markus and Reisgen, Uwe},
  title     = {Thermisches Direktf{\"u}gen von Metall und Kusntstoff: eine Alternative zur Klebtechnik},
  series = {Adh{\"a}sion : Kleben \& Dichten},
  volume    = {56},
  journal   = {Adh{\"a}sion : Kleben \& Dichten},
  number    = {11},
  publisher = {Springer Vieweg},
  address   = {Wiesbaden},
  issn      = {0001-8198 (E-Journal); 0001-8198 (Print)},
  doi       = {10.1007/s35145-012-0005-x},
  pages     = {36 -- 40},
  year      = {2012},
  abstract  = {Im Rahmen des Exzellenzclusters „Integrative Produktionstechnik f{\"u}r Hochlohnl{\"a}nder" der RWTHAachen University werden derzeit alternative Verfahren zur Herstellung von Metall/Kunststoff- Verbindungen untersucht. Eines davon ist das thermische Direktf{\"u}gen, das eine stoffschl{\"u}ssige Verbindung zwischen Kunststoff und Metall erm{\"o}glicht und ohne die Verwendung von Klebstoffen, Haftvermittlern oder mechanischen Verbindungshilfen auskommt.},
  language  = {de}
}
@article{ReisgenSchleserMokrovetal.2012,
  author    = {Reisgen, Uwe and Schleser, Markus and Mokrov, Oleg and Zabirov, Alexander and F{\"u}ssel, Uwe and Schnick, Michael and Hertel, Martin and Jaeckel, Sebastian},
  title     = {Modelling and visualisation of the GMA process},
  series = {Welding and Cutting},
  volume    = {11},
  journal   = {Welding and Cutting},
  number    = {4},
  publisher = {DVS Verlag},
  address   = {D{\"u}sseldorf},
  issn      = {1612-3433},
  pages     = {242 -- 249},
  year      = {2012},
  language  = {en}
}
@article{HoetterFateriGebhardt2012,
  author    = {H{\"o}tter, Jan-Steffen and Fateri, Miranda and Gebhardt, Andreas},
  title     = {Selective laser melting of metals: desktop machines open up new chances even for small companies},
  series = {Advanced materials research},
  volume    = {622-623},
  journal   = {Advanced materials research},
  publisher = {Trans Tech Publ.},
  address   = {Baech},
  issn      = {1662-8985 (E-Journal); 1022-6680 (Print)},
  doi       = {10.4028/www.scientific.net/AMR.622-623.461},
  pages     = {461 -- 465},
  year      = {2012},
  abstract  = {Additive manufacturing (AM) of metal parts by using Selective Laser Melting (SLM) has become a powerful tool mostly in the area of automotive, aerospace engineering and others. Especially in the field of dentistry, jewelry and related branches that require individualized or even one-of-a-kind products, the direct digital manufacturing process opens up new ways of design and manufacturing. In these fields, mostly small and medium sized businesses (SME) are operating which do not have sufficient human and economic resources to invest in this technology. But to stay competitive, the application of AM can be regarded as a necessity. In this situation a new desktop machine (Realizer SLM 50) was introduced that cost about 1/3 of a shop floor SLM machine and promises small quality parts. To find out whether the machine really is an alternative for SMEs the University of Applied Science, Aachen, Germany, designed, build and optimized typical parts from the dentistry and the jewelry branches using CoCr and silver material, the latter being new with this application. The paper describes the SLM procedure and how to find and optimize the most important parameters. The test is accompanied by digital simulation in order to verify the build parameters and to plan future builds. The procedure is shown as well as the resulting parts made from CoCr and silver material.},
  language  = {en}
}
@article{LeidingerNoistenWollert2012,
  author    = {Leidinger, Rafael and Noisten, Thomas and Wollert, J{\"o}rg},
  title     = {Realtime automation networks in moVing industrial environments},
  series = {Journal of systemics, cybernetics and informatics},
  volume    = {Vol. 10},
  journal   = {Journal of systemics, cybernetics and informatics},
  number    = {Iss. 2},
  publisher = {IIIC},
  address   = {Orlando},
  issn      = {1690-4532},
  pages     = {52 -- 56},
  year      = {2012},
  abstract  = {The radio-based wireless data communication has made the realization of new technical solutions possible in many fields of the automation technology (AT). For about ten years, a constant disproportionate growth of wireless technologies can be observed in the automation technology. However, it shows that especially for the AT, conventional technologies of office automation are unsuitable and/or not manageable. The employment of mobile services in the industrial automation technology has the potential of significant cost and time savings. This leads to an increased productivity in various fields of the AT, for example in the factory and process automation or in production logistics. In this paper technologies and solutions for an automation-suited supply of mobile wireless services will be introduced under the criteria of real time suitability, IT-security and service orientation. Emphasis will be put on the investigation and development of wireless convergence layers for different radio technologies, on the central provision of support services for an easy-to-use, central, backup enabled management of combined wired / wireless networks and on the study on integrability in a Profinet real-time Ethernet network.},
  language  = {en}
}
@article{GebhardtFateri2013,
  author    = {Gebhardt, Andreas and Fateri, Miranda},
  title     = {3D printing and its applications},
  series = {RTejournal - Forum f{\"u}r Rapid Technologie},
  volume    = {10},
  journal   = {RTejournal - Forum f{\"u}r Rapid Technologie},
  number    = {1},
  publisher = {Fachhochschule Aachen},
  address   = {Aachen},
  issn      = {1614-0923},
  url       = {http://nbn-resolving.de/urn:nbn:de:0009-2-35626},
  year      = {2013},
  abstract  = {Eine zunehmende Anzahl von Artikeln in Publikumszeitschriften und Journalen r{\"u}ckt die direkte Herstellung von Bauteilen und Figuren immer mehr in das Bewusstsein einer breiten {\"O}ffentlichkeit. Leider ergibt sich nur selten ein einigermaßen vollst{\"a}ndiges Bild davon, wie und in welchen Lebensbereichen diese Techniken unseren Alltag ver{\"a}ndern werden. Das liegt auch daran, dass die meisten Artikel sehr technisch gepr{\"a}gt sind und sich nur punktuell auf Beispiele st{\"u}tzen. Dieser Beitrag geht von den Bed{\"u}rfnissen der Menschen aus, wie sie z.B. in der Maslow'schen Bed{\"u}rfnispyramide strukturiert dargestellt sind und unterstreicht dadurch, dass 3D Printing (oder Additive Manufacturing resp. Rapid Prototyping) bereits alle Lebensbereiche erfasst hat und im Begriff ist, viele davon zu revolutionieren.},
  language  = {en}
}
@article{ReisgenSchleserSchiebahn2013,
  author    = {Reisgen, Uwe and Schleser, Markus and Schiebahn, Alexander},
  title     = {Untersuchung zum Einfluss von Maschineneigenschaften von Schweißzangen zum Widerstandspunktschweißen auf das Schweißergebnis},
  series = {Schweissen und Schneiden : Fachzeitschrift f{\"u}r Schweißen und verwandte Verfahren},
  volume    = {Bd. 65},
  journal   = {Schweissen und Schneiden : Fachzeitschrift f{\"u}r Schweißen und verwandte Verfahren},
  number    = {H. 6},
  publisher = {DVS Verl.},
  address   = {D{\"u}sseldorf},
  issn      = {0036-7184},
  pages     = {309 -- 313},
  year      = {2013},
  language  = {de}
}
@article{RamazaniLiMukherjeeetal.2013,
  author    = {Ramazani, Ali and Li, Yang and Mukherjee, Krishnendu and Prahl, Ulrich and Bleck, Wolfgang and Abdurakhmanov, Aydemir and Schleser, Markus and Reisgen, Uwe},
  title     = {Microstructure evolution simulation in hot rolled DP600 steel during gas metal arc welding},
  series = {Computational materials science},
  volume    = {Vol. 68},
  journal   = {Computational materials science},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1879-0801 (E-Book); 0927-0256 (Print)},
  pages     = {107 -- 116},
  year      = {2013},
  language  = {en}
}
@article{GebhardtFateri2014,
  author    = {Gebhardt, Andreas and Fateri, Miranda},
  title     = {3D-Drucken und die Anwendungen},
  series = {RTejournal - Forum f{\"u}r Rapid Technologie},
  volume    = {11 (2014)},
  journal   = {RTejournal - Forum f{\"u}r Rapid Technologie},
  number    = {1},
  issn      = {1614-0923},
  pages     = {1 -- 9},
  year      = {2014},
  language  = {de}
}
@article{GebhardtHoetterZiebura2014,
  author    = {Gebhardt, Andreas and H{\"o}tter, Jan-Steffen and Ziebura, Dawid},
  title     = {Impact of SLM build parameters on the surface quality},
  series = {RTejournal - Forum f{\"u}r Rapid Technologien},
  volume    = {11 (2014)},
  journal   = {RTejournal - Forum f{\"u}r Rapid Technologien},
  number    = {1},
  issn      = {1614-0923},
  pages     = {1 -- 14},
  year      = {2014},
  language  = {de}
}
@article{FiedlerHennMelcher2014,
  author    = {Fiedler, Gerda and Henn, Gudrun and Melcher, Karin},
  title     = {ANPAK - ein semesterbegleitender Anpassungskurs},
  series = {Zeitschrift f{\"u}r Hochschulentwicklung},
  volume    = {9},
  journal   = {Zeitschrift f{\"u}r Hochschulentwicklung},
  number    = {4},
  publisher = {{\"O}GHD},
  address   = {Wien},
  issn      = {2219-6994},
  pages     = {85 -- 100},
  year      = {2014},
  abstract  = {In Folge mehrj{\"a}hriger statistischer Untersuchungen an der FH Aachen ist unter anderem ein Eingangstest entstanden, der als Diagnosetool f{\"u}r einen erfolgreichen Studieneinstieg verwendet wird. Es hat sich herausgestellt, dass ein Testergebnis von weniger als 25 (von maximal 56 erreichbaren) Punkten die Chance auf einen erfolgreichen Studieneinstieg deutlich verringert. Ungef{\"a}hr die H{\"a}lfte aller Erstsemester hat weniger als 25 Punkte im Eingangstest. Weniger als 20 \% dieser Gruppe bestehen innerhalb eines Jahres die Klausur Mathematik 1. Die investierte Zeit von zwei Semestern ist mit Blick auf den Wissenszuwachs und damit letztendlich den Studienerfolg nicht effizient genutzt. Deshalb haben wir im WS 2013/14 einen semesterbegleitenden Anpassungskurs f{\"u}r diese Gruppe installiert. Ziel eines solchen Kurses ist es, die Student/innen innerhalb eines Jahres in die Lage zu versetzen, nach zwei Semestern problemlos den Vorlesungen in Mathematik zu folgen. Dieser Artikel beschreibt das Konzept dieses Anpassungskurses und zeigt erste Ergebnisse und Probleme des Pilotdurchgangs auf.},
  language  = {de}
}
@article{FateriGebhardtThuemmleretal.2014,
  author    = {Fateri, Miranda and Gebhardt, Andreas and Th{\"u}mmler, Stefan and Thurn, Laura},
  title     = {Experimental investigation on selective laser melting of glass},
  series = {Physics procedia : 8th International Conference on Laser Assisted Net Shape Engineering LANE 2014},
  volume    = {56 (2014)},
  journal   = {Physics procedia : 8th International Conference on Laser Assisted Net Shape Engineering LANE 2014},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1875-3892 (E-Journal); 1875-3884 (Print)},
  doi       = {10.1016/j.phpro.2014.08.118},
  pages     = {357 -- 364},
  year      = {2014},
  language  = {en}
}
@article{Thomas2014,
  author    = {Thomas, Axel},
  title     = {Generation Y},
  series = {P.T. : Magazin f{\"u}r Wirtschaft und Gesellschaft},
  volume    = {10},
  journal   = {P.T. : Magazin f{\"u}r Wirtschaft und Gesellschaft},
  number    = {3},
  publisher = {OPS Netzwerk},
  address   = {Leipzig},
  issn      = {1860-501X},
  pages     = {6 -- 9},
  year      = {2014},
  language  = {de}
}
@article{ThomasWassenberg2014,
  author    = {Thomas, Axel and Wassenberg, Gerd},
  title     = {Erfolgreich sein im Kampf um die besten Talente : Employer Branding},
  series = {Wirtschaftliche Nachrichten der Industrie- und Handelskammer Aachen},
  journal   = {Wirtschaftliche Nachrichten der Industrie- und Handelskammer Aachen},
  publisher = {IHK Aachen},
  address   = {Aachen},
  year      = {2014},
  language  = {de}
}
@article{Wollert2014,
  author    = {Wollert, J{\"o}rg},
  title     = {Funkstandards f{\"u}r Sensornetzwerke},
  series = {Elektronik : Fachmedium f{\"u}r industrielle Anwender und Entwickler},
  volume    = {Bd. 63},
  journal   = {Elektronik : Fachmedium f{\"u}r industrielle Anwender und Entwickler},
  number    = {H. 12},
  publisher = {WEKA-Fachmedien},
  address   = {Haar},
  issn      = {0013-5658},
  pages     = {36 -- 41},
  year      = {2014},
  language  = {de}
}
@article{Wollert2014,
  author    = {Wollert, J{\"o}rg},
  title     = {Echtzeit-Ethernet : Protokoll-Reigen},
  series = {Elektronik : Fachmedium f{\"u}r industrielle Anwender und Entwickler},
  volume    = {Bd. 63},
  journal   = {Elektronik : Fachmedium f{\"u}r industrielle Anwender und Entwickler},
  number    = {H. 26},
  publisher = {WEKA-Fachmedien},
  address   = {Haar},
  issn      = {0013-5658},
  pages     = {24 -- 31},
  year      = {2014},
  language  = {de}
}
@article{Wollert2014,
  author    = {Wollert, J{\"o}rg},
  title     = {Der Embedded Wireless-Report},
  series = {Elektronik : Fachmedium f{\"u}r industrielle Anwender und Entwickler ; Sonderh. Wireless : Fachmedium f{\"u}r Entwicklungen funkbasierter Systeme},
  journal   = {Elektronik : Fachmedium f{\"u}r industrielle Anwender und Entwickler ; Sonderh. Wireless : Fachmedium f{\"u}r Entwicklungen funkbasierter Systeme},
  publisher = {WEKA-Fachmedien},
  address   = {Haar},
  issn      = {0013-5658},
  pages     = {18 -- 25},
  year      = {2014},
  language  = {de}
}
@article{Wollert2014,
  author    = {Wollert, J{\"o}rg},
  title     = {Echtzeit-Ethernet mit Standardtechnik},
  series = {Elektronik : Fachmedium f{\"u}r industrielle Anwender und Entwickler ; Sonderh. Embedded : Fachmagazin f{\"u}r die Entwicklung von Embedded-Systemen},
  volume    = {Bd. 63},
  journal   = {Elektronik : Fachmedium f{\"u}r industrielle Anwender und Entwickler ; Sonderh. Embedded : Fachmagazin f{\"u}r die Entwicklung von Embedded-Systemen},
  number    = {H. 12},
  publisher = {WEKA-Fachmedien},
  address   = {Haar},
  issn      = {0013-5658},
  pages     = {28 -- 32},
  year      = {2014},
  language  = {de}
}
@article{Wollert2014,
  author    = {Wollert, J{\"o}rg},
  title     = {Feldbustechnologie},
  series = {Factory : der Durchblick in der Technik},
  journal   = {Factory : der Durchblick in der Technik},
  publisher = {WEKA-Industriemedien},
  address   = {Wien},
  pages     = {Publ. online},
  year      = {2014},
  language  = {de}
}