@article{NeuJanserKhatibietal.2017,
  author    = {Neu, Eugen and Janser, Frank and Khatibi, Akbar A. and Orifici, Adrian C.},
  title     = {Fully Automated Operational Modal Analysis using multi-stage clustering},
  series = {Mechanical Systems and Signal Processing},
  volume    = {Vol. 84, Part A},
  journal   = {Mechanical Systems and Signal Processing},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0888-3270},
  doi       = {10.1016/j.ymssp.2016.07.031},
  pages     = {308 -- 323},
  year      = {2017},
  language  = {en}
}
@article{NeuJanserKhatibietal.2016,
  author    = {Neu, Eugen and Janser, Frank and Khatibi, Akbar A. and Orifici, Adrian C.},
  title     = {Automated modal parameter-based anomaly detection under varying wind excitation},
  series = {Structural Health Monitoring},
  volume    = {15},
  journal   = {Structural Health Monitoring},
  number    = {6},
  publisher = {Sage},
  address   = {London},
  issn      = {1475-9217},
  doi       = {10.1177/1475921716665803},
  pages     = {1 -- 20},
  year      = {2016},
  abstract  = {Wind-induced operational variability is one of the major challenges for structural health monitoring of slender engineering structures like aircraft wings or wind turbine blades. Damage sensitive features often show an even bigger sensitivity to operational variability. In this study a composite cantilever was subjected to multiple mass configurations, velocities and angles of attack in a controlled wind tunnel environment. A small-scale impact damage was introduced to the specimen and the structural response measurements were repeated. The proposed damage detection methodology is based on automated operational modal analysis. A novel baseline preparation procedure is described that reduces the amount of user interaction to the provision of a single consistency threshold. The procedure starts with an indeterminate number of operational modal analysis identifications from a large number of datasets and returns a complete baseline matrix of natural frequencies and damping ratios that is suitable for subsequent anomaly detection. Mahalanobis distance-based anomaly detection is then applied to successfully detect the damage under varying severities of operational variability and with various degrees of knowledge about the present operational conditions. The damage detection capabilities of the proposed methodology were found to be excellent under varying velocities and angles of attack. Damage detection was less successful under joint mass and wind variability but could be significantly improved through the provision of the currently encountered operational conditions.},
  language  = {en}
}
@inproceedings{WuKemper2016,
  author    = {Wu, Ziyi and Kemper, Hans},
  title     = {The optimal 48 V - battery pack for a specific load profile of a heavy duty vehicle},
  series = {8. Internationale Fachtagung Kraftwerk Batterie : 26. - 27. April 2016, M{\"u}nster, Deutschland},
  booktitle = {8. Internationale Fachtagung Kraftwerk Batterie : 26. - 27. April 2016, M{\"u}nster, Deutschland},
  year      = {2016},
  language  = {en}
}
@inproceedings{NeuJanserKhatibietal.2016,
  author    = {Neu, Eugen and Janser, Frank and Khatibi, Akbar A. and Orifici, Adrian C.},
  title     = {In-flight vibration-based structural health monitoring of aircraft wings},
  series = {30th Congress of the internatonal council of the aeronautical sciences : 25.-30. September 2016, Daejeon, Korea},
  booktitle = {30th Congress of the internatonal council of the aeronautical sciences : 25.-30. September 2016, Daejeon, Korea},
  pages     = {10 Seiten},
  year      = {2016},
  abstract  = {This work presents a methodology for automated damage-sensitive feature extraction and anomaly detection under multivariate operational variability for in-flight assessment of wings. The method uses a passive excitation approach, i. e. without the need for artificial actuation. The modal system properties (natural frequencies and damping ratios) are used as damage-sensitive features. Special emphasis is placed on the use of Fiber Bragg Grating (FBG) sensing technology and the consideration of Operational and Environmental Variability (OEV). Measurements from a wind tunnel investigation with a composite cantilever equipped with FBG and piezoelectric sensors are used to successfully detect an impact damage. In addition, the feasibility of damage localisation and severity estimation is evaluated based on the coupling found between damageand OEV-induced feature changes.},
  language  = {en}
}
@article{PetersonRoethUibel2017,
  author    = {Peterson, Leif Arne and R{\"o}th, Thilo and Uibel, Thomas},
  title     = {Einsatz von Holzwerkstoffen in Fahrzeugstrukturen},
  series = {Bauen mit Holz},
  journal   = {Bauen mit Holz},
  number    = {3},
  publisher = {Bruderverlag},
  address   = {K{\"o}ln},
  issn      = {0005-6545},
  pages     = {32 -- 38},
  year      = {2017},
  language  = {de}
}
@inproceedings{PetersonRoethUibel2017,
  author    = {Peterson, Leif Arne and R{\"o}th, Thilo and Uibel, Thomas},
  title     = {Holzwerkstoffe in Karosseriestrukturen},
  series = {Tagungsband Aachener Holzbautagung 2017},
  booktitle = {Tagungsband Aachener Holzbautagung 2017},
  editor    = {Uibel, Thormas and Peterson, Leif Arne and Baumann, Marcus},
  issn      = {2197-4489},
  pages     = {34 -- 45},
  year      = {2017},
  language  = {de}
}
@article{WeiheErnstRoethetal.2013,
  author    = {Weihe, Stefan and Ernst, Ansgar and R{\"o}th, Thilo and Proksch, Johannes},
  title     = {Aluminium-Stahl-Verbundguss im Nutzfahrzeugbau},
  series = {ATZ - Automobiltechnische Zeitschrift},
  volume    = {115},
  journal   = {ATZ - Automobiltechnische Zeitschrift},
  number    = {4},
  publisher = {Springer Fachmedien Wiesbaden},
  issn      = {2192-8800 (Online)},
  pages     = {312 -- 316},
  year      = {2013},
  abstract  = {In modernen Fahrzeugkarosserien der Großserie kommen zunehmend Materialmischbauweisen zur Anwendung. In Zusammenarbeit der Daimler AG, der Tower Automotive Holding GmbH, der Imperia GmbH sowie der Partnerunternehmen KSM Castings GmbH und Schaufler Tooling GmbH \& Co. KG wird das Leichtbaupotenzial von Aluminiumverbundguss-Stahlblech-Hybriden am Beispiel des vorderen Dachquertr{\"a}gers des Mercedes-Benz Viano/Vito ausf{\"u}hrlich untersucht.},
  language  = {de}
}
@inproceedings{SchulzeMuehleisenFeyerl2018,
  author    = {Schulze, Sven and M{\"u}hleisen, M. and Feyerl, G{\"u}nter},
  title     = {Adaptive energy management strategy for a heavy-duty truck with a P2-hybrid topology},
  series = {18. Internationales Stuttgarter Symposium. Proceedings},
  booktitle = {18. Internationales Stuttgarter Symposium. Proceedings},
  publisher = {Springer Vieweg},
  address   = {Wiesbaden},
  doi       = {10.1007/978-3-658-21194-3},
  pages     = {75 -- 89},
  year      = {2018},
  language  = {en}
}
@article{RoethPielenWolffetal.2018,
  author    = {R{\"o}th, Thilo and Pielen, Michael and Wolff, Klaus and L{\"u}diger, Thomas},
  title     = {Urbane Fahrzeugkonzepte f{\"u}r die Shared Mobility},
  series = {Automobiltechnische Zeitschrift - ATZ},
  volume    = {120},
  journal   = {Automobiltechnische Zeitschrift - ATZ},
  number    = {1},
  publisher = {Springer Vieweg},
  address   = {Wiesbaden},
  issn      = {0001-2785},
  doi       = {10.1007/s35148-017-0176-8},
  pages     = {18 -- 23},
  year      = {2018},
  abstract  = {Urbane Mobilit{\"a}tskonzepte der Zukunft erfordern neue Unternehmensformen, idealerweise aus Old Economy und New Economy, sowie eine enge Anbindung an die gesellschaftsrelevante Zukunftsforschung. F{\"u}r neue Fahrzeugkonzepte des Carsharing bedeutet dies, dass alle kostenverursachenden Faktoren erfasst und analysiert werden m{\"u}ssen. Die FH Aachen, share2drive und FEV geben einen Ausblick auf die zuk{\"u}nftige Fahrzeugklasse der Personal Public Vehicles als „Rolling Device".},
  language  = {de}
}
@inproceedings{NowackRoethBuehrigPolaczeketal.2008,
  author    = {Nowack, N. and R{\"o}th, Thilo and B{\"u}hrig-Polaczek, A. and Klaus, G.},
  title     = {Advanced Sheet Metal Components Reinforced by Light Metal Cast Structures},
  series = {Aluminium alloys : their physical and mechanical properties ; [proceedings of the 11th International Conference on Aluminium Alloys, 22 - 26 Sept. 2008, Aachen, Germany ; ICAA 11]},
  booktitle = {Aluminium alloys : their physical and mechanical properties ; [proceedings of the 11th International Conference on Aluminium Alloys, 22 - 26 Sept. 2008, Aachen, Germany ; ICAA 11]},
  number    = {2},
  editor    = {Hirsch, J{\"u}rgen},
  isbn      = {978-3-527-32367-8},
  pages     = {2374 -- 2381},
  year      = {2008},
  language  = {en}
}
@inproceedings{PaslighFunkeRoethetal.2010,
  author    = {Pasligh, N. and Funke, D. and R{\"o}th, Thilo and Krack, R.},
  title     = {Leichtbau Quertrager als Stahlblech-Aluminiumdruckguss-Hybrid - Von der numerischen Berechnung bis zum realen Prototypen},
  series = {VDI BERICHTE},
  booktitle = {VDI BERICHTE},
  publisher = {VDI Verlag},
  address   = {D{\"u}sseldorf},
  isbn      = {978-3-18-092107-5},
  pages     = {688 Seiten},
  year      = {2010},
  language  = {de}
}
@inproceedings{LaoBuehrigPolaczekRoeth2011,
  author    = {Lao, B. and B{\"u}hrig-Polaczek, A. and R{\"o}th, Thilo},
  title     = {Funktionsintegrierte Leichtbaustrukturen in gussintensiver Metall-Hybridbauweise},
  series = {Verbundwerkstoffe und Werkstoffverbunde: Tagungsband zum 18. Symposium ; 30.03.2011 bis 01.04.2011, Chemnitz},
  booktitle = {Verbundwerkstoffe und Werkstoffverbunde: Tagungsband zum 18. Symposium ; 30.03.2011 bis 01.04.2011, Chemnitz},
  editor    = {Wielage, Bernhard},
  publisher = {Eigenverlag},
  address   = {Chemnitz},
  isbn      = {978-3-00-033801-4},
  pages     = {413 -- 421},
  year      = {2011},
  language  = {de}
}
@article{WeiheAnsgarRoethetal.2013,
  author    = {Weihe, Stefan and Ansgar, Ernst and R{\"o}th, Thilo and Proksch, Johannes},
  title     = {Leichtmetall-Stahl-Verbundguss im Nutzfahrzeugbau},
  series = {Lightweight Design},
  volume    = {6},
  journal   = {Lightweight Design},
  number    = {2},
  publisher = {Springer},
  address   = {Berlin},
  issn      = {2192-8738 (Online)},
  pages     = {38 -- 43},
  year      = {2013},
  abstract  = {In modernen Fahrzeugkarosserien der Großserie kommen zunehmend Materialmischbauweisen zur Anwendung. In Zusammenarbeit der Daimler AG, der Tower Automotive Holding GmbH, der Imperia GmbH sowie der Partnerunternehmen KSM Castings GmbH und Schaufler Tooling GmbH \& Co. KG wird das Leichtbaupotenzial von Stahlblech-AluminiumverbundgussHybriden am Beispiel des vorderen Dachquertr{\"a}gers des Mercedes-Benz Viano/Vito ausf{\"u}hrlich untersucht.},
  language  = {de}
}
@incollection{RoethDeutskensKreiskoetheretal.2018,
  author    = {R{\"o}th, Thilo and Deutskens, Christoph and Kreisk{\"o}ther, Kai and Heimes, Heiner Hans and Schittny, Bastian and Ivanescu, Sebastian and Kleine B{\"u}ning, Max and Reinders, Christian and Wessels, Saskia and Haunreiter, Andreas and Reisgen, Uwe and Thiele, Regina and Hameyer, Kay and Doncker, Rik W. de and Sauer, Uwe and Hoek, Hauke van and H{\"u}bner, Mareike and Hennen, Martin and Stolze, Thilo and Vetter, Andreas and Hagedorn, J{\"u}rgen and M{\"u}ller, Dirk and Rewitz, Kai and Wesseling, Mark and Flieger, Bj{\"o}rn},
  title     = {Entwicklung von elektrofahrzeugspezifischen Systemen},
  series = {Elektromobilit{\"a}t},
  booktitle = {Elektromobilit{\"a}t},
  publisher = {Springer Vieweg},
  address   = {Berlin, Heidelberg},
  isbn      = {978-3-662-53137-2},
  doi       = {10.1007/978-3-662-53137-2_6},
  pages     = {279 -- 386},
  year      = {2018},
  abstract  = {Die Batterie ist eine der absolut zentralen Komponenten des Elektrofahrzeugs. Die serielle Entwicklung und Produktion dieser Batterien und die Verbesserung der Leistungen wird entscheidend f{\"u}r den Erfolg der Elektromobilit{\"a}t sein. Die Batterie ist jedoch nicht das einzige elektrofahrzeugspezifische System, das neu entwickelt, umkonzipiert oder verbessert werden muss. So sind ebenso die Entwicklung der neuen Fahrzeugstruktur sowie des elektrifizierten Antriebsstranges Teil dieses Kapitels. Weiterhin wird ein Blick auf das bedeutende Thema des Thermomanagements geworfen.},
  language  = {de}
}
@incollection{RoethPielen2018,
  author    = {R{\"o}th, Thilo and Pielen, Michael},
  title     = {Personal Public Vehicle - ein urbanes Fahrzeugkonzept f{\"u}r die „Shared Mobility" der Zukunft},
  series = {Karosseriebautage Hamburg 2018, 16. ATZ-Fachtagung},
  booktitle = {Karosseriebautage Hamburg 2018, 16. ATZ-Fachtagung},
  publisher = {Springer Vieweg},
  address   = {Wiesbaden},
  doi       = {10.1007/978-3-658-22038-9_13},
  pages     = {189 -- 199},
  year      = {2018},
  abstract  = {Die urbane Mobilit{\"a}t ist im Wandel und insbesondere neue innovative Gesch{\"a}ftsmodelle werden einen wesentlichen Teil zur L{\"o}sung von k{\"u}nftigen Mobilit{\"a}tsbed{\"u}rfnissen beitragen. Die sogenannte „Shared Mobility" gilt aktuell neben der Elektrifizierung des Antriebes und autonomem Fahrzeugtechnologien als einer der wichtigsten Trendthemen in der Automobilindustrie. Neue Mobilit{\"a}tsdienstleistungen verlangen dabei verst{\"a}rkt auch neue Fahrzeugkonzepte.},
  language  = {de}
}
@article{KhayyamJamaliBabHadiasharetal.2020,
  author    = {Khayyam, Hamid and Jamali, Ali and Bab-Hadiashar, Alireza and Esch, Thomas and Ramakrishna, Seeram and Jalili, Mahdi and Naebe, Minoo},
  title     = {A Novel Hybrid Machine Learning Algorithm for Limited and Big Data Modeling with Application in Industry 4.0},
  series = {IEEE Access},
  volume    = {8},
  journal   = {IEEE Access},
  number    = {Art. 9108222},
  publisher = {IEEE},
  address   = {New York, NY},
  issn      = {2169-3536},
  doi       = {10.1109/ACCESS.2020.2999898},
  pages     = {111381 -- 111393},
  year      = {2020},
  abstract  = {To meet the challenges of manufacturing smart products, the manufacturing plants have been radically changed to become smart factories underpinned by industry 4.0 technologies. The transformation is assisted by employment of machine learning techniques that can deal with modeling both big or limited data. This manuscript reviews these concepts and present a case study that demonstrates the use of a novel intelligent hybrid algorithms for Industry 4.0 applications with limited data. In particular, an intelligent algorithm is proposed for robust data modeling of nonlinear systems based on input-output data. In our approach, a novel hybrid data-driven combining the Group-Method of Data-Handling and Singular-Value Decomposition is adapted to find an offline deterministic model combined with Pareto multi-objective optimization to overcome the overfitting issue. An Unscented-Kalman-Filter is also incorporated to update the coefficient of the deterministic model and increase its robustness against data uncertainties. The effectiveness of the proposed method is examined on a set of real industrial measurements.},
  language  = {en}
}
@article{HoevelerBauknechtWolfetal.2020,
  author    = {Hoeveler, B. and Bauknecht, Andr{\´e} and Wolf, C. Christian and Janser, Frank},
  title     = {Wind-Tunnel Study of a Wing-Embedded Lifting Fan Remaining Open in Cruise Flight},
  series = {Journal of Aircraft},
  volume    = {57},
  journal   = {Journal of Aircraft},
  number    = {4},
  publisher = {AIAA},
  address   = {Reston, Va.},
  issn      = {1533-3868},
  doi       = {10.2514/1.C035422},
  year      = {2020},
  abstract  = {It is investigated whether a nonrotating lifting fan remaining uncovered during cruise flight, as opposed to being covered by a shutter system, can be realized with limited additional drag and loss of lift during cruise flight. A wind-tunnel study of a wing-embedded lifting fan has been conducted at the Side Wind Test Facility G{\"o}ttingen of DLR, German Aerospace Center in G{\"o}ttingen using force, pressure, and stereoscopic particle image velocimetry techniques. The study showed that a step on the lower side of the wing in front of the lifting fan duct increases the lift-to-drag ratio of the whole model by up to 25\% for all positive angles of attack. Different sizes and inclinations of the step had limited influence on the surface pressure distribution. The data indicate that these parameters can be optimized to maximize the lift-to-drag ratio. A doubling of the curvature radius of the lifting fan duct inlet lip on the upper side of the wing affected the lift-to-drag ratio by less than 1\%. The lifting fan duct inlet curvature can therefore be optimized to maximize the vertical fan thrust of the rotating lifting fan during hovering without affecting the cruise flight performance with a nonrotating fan.},
  language  = {en}
}
@techreport{HebelMerkensFeyerletal.2021,
  author    = {Hebel, Christoph and Merkens, Torsten and Feyerl, G{\"u}nter and Kemper, Hans and Busse, Daniel},
  title     = {Elektromobilit{\"a}t - Verbundprojekt "COSTARTebus": Comprehensive strategy to accelerate the integration of electric-buses into existing public transport systems - Teilprojekt A : Berichtszeitraum: 01.01.2018-31.10.2020},
  publisher = {Fachhochschule Aachen},
  address   = {Aachen},
  pages     = {219 Seiten},
  year      = {2021},
  language  = {de}
}
@techreport{ThomaLaarmannMerkensetal.2020,
  author    = {Thoma, Andreas and Laarmann, Lukas and Merkens, Torsten and Franzke, Till and M{\"o}hren, Felix and Buttermann, Lilly and van der Weem, Dirk and Fischer, Maximilian and Misch, Philipp and B{\"o}hme, Mirijam and R{\"o}th, Thilo and Hebel, Christoph and Ritz, Thomas and Franke, Marina and Braun, Carsten},
  title     = {Entwicklung eines intermodalen Mobilit{\"a}tskonzeptes f{\"u}r die Pilotregion NRW/Rhein-Maas Euregio und Schaffung voller Kundenakzeptanz durch Transfer von Standards aus dem PKW-Bereich auf ein Flugtaxi : Schlussbericht : Projektakronym: SkyCab (Kategorie B) : Laufzeit in Monaten: 6 : Hauptthema: Kategorie B: Innovative Ideen mit Bezug zu UAS/Flugtaxis},
  publisher = {FH Aachen},
  address   = {Aachen},
  pages     = {97 Seiten},
  year      = {2020},
  language  = {de}
}
@incollection{HebelHerrmannRitzetal.2022,
  author    = {Hebel, Christoph and Herrmann, Ulf and Ritz, Thomas and R{\"o}th, Thilo and Anthrakidis, Anette and B{\"o}ker, J{\"o}rg and Franzke, Till and Grodzki, Thomas and Merkens, Torsten and Sch{\"o}ttler, Mirjam},
  title     = {FlexSHARE - Methodisches Framework zur innovativen Gestaltung der urbanen Mobilit{\"a}t durch Sharing- Angebote},
  series = {Transforming Mobility - What Next?},
  booktitle = {Transforming Mobility - What Next?},
  publisher = {Springer Gabler},
  address   = {Wiesbaden},
  isbn      = {978-3-658-36429-8},
  doi       = {10.1007/978-3-658-36430-4_10},
  pages     = {153 -- 169},
  year      = {2022},
  abstract  = {Das Ziel des INTERREG-Projektes „SHAREuregio" (FKZ: 34.EFRE-0300134) ist es, grenz{\"u}berschreitende Mobilit{\"a}t in der Euregio Rhein-Maas-Nord zu erm{\"o}glichen und zu f{\"o}rdern. Dazu soll ein elektromobiles Car- und Bikesharing- System entwickelt und in der Stadt M{\"o}nchengladbach, im Kreis Viersen sowie in den Gemeinden Roermond und Venlo (beide NL) zusammen mit den Partnern Wirtschaftsf{\"o}rderung M{\"o}nchengladbach, Wirtschaftsf{\"o}rderung f{\"u}r den Kreis Viersen, NEW AG, Goodmoovs (NL), Greenflux (NL) und der FH Aachen implementiert werden. Zun{\"a}chst richtet sich das Angebot, bestehend aus 40 Elektroautos und 40 Elektrofahrr{\"a}dern, an Unternehmen und wird nach einer Erprobungsphase, mit einer gr{\"o}ßeren Anzahl an Fahrzeugen, auch f{\"u}r Privatpersonen verf{\"u}gbar gemacht werden. Die Fahrzeuge stehen bei den jeweiligen Anwendungspartnern in Deutschland und den Niederlanden. Im Rahmen dieses Projektes hat die FH Aachen „FlexSHARE" entwickelt - ein methodisches Framework zur innovativen Gestaltung urbaner Sharing- Angebote. Das Framework erm{\"o}glicht es, anhand von messbaren Kenngr{\"o}ßen, bedarfsgerechte und auf die Region abgestimmte Sharing-Systeme zu entwickeln.},
  language  = {de}
}
@article{BergmannMoehrenBraunetal.2023,
  author    = {Bergmann, Ole and M{\"o}hren, Felix and Braun, Carsten and Janser, Frank},
  title     = {On the influence of elasticity on swept propeller noise},
  series = {AIAA SCITECH 2023 Forum},
  journal   = {AIAA SCITECH 2023 Forum},
  publisher = {AIAA},
  doi       = {10.2514/6.2023-0210},
  year      = {2023},
  abstract  = {High aerodynamic efficiency requires propellers with high aspect ratios, while propeller sweep potentially reduces noise. Propeller sweep and high aspect ratios increase elasticity and coupling of structural mechanics and aerodynamics, affecting the propeller performance and noise. Therefore, this paper analyzes the influence of elasticity on forward-swept, backward-swept, and unswept propellers in hover conditions. A reduced-order blade element momentum approach is coupled with a one-dimensional Timoshenko beam theory and Farassat's formulation 1A. The results of the aeroelastic simulation are used as input for the aeroacoustic calculation. The analysis shows that elasticity influences noise radiation because thickness and loading noise respond differently to deformations. In the case of the backward-swept propeller, the location of the maximum sound pressure level shifts forward by 0.5 °, while in the case of the forward-swept propeller, it shifts backward by 0.5 °. Therefore, aeroacoustic optimization requires the consideration of propeller deformation.},
  language  = {en}
}
@article{KhayyamJamaliBabHadiasharetal.2020,
  author    = {Khayyam, Hamid and Jamali, Ali and Bab-Hadiashar, Alireza and Esch, Thomas and Ramakrishna, Seeram and Jalil, Mahdi and Naebe, Minoo},
  title     = {A Novel Hybrid Machine Learning Algorithm for Limited and Big Data Modelling with Application in Industry 4.0},
  series = {IEEE Access},
  journal   = {IEEE Access},
  publisher = {IEEE},
  address   = {New York, NY},
  isbn      = {2169-3536},
  doi       = {10.1109/ACCESS.2020.2999898},
  pages     = {1 -- 12},
  year      = {2020},
  abstract  = {To meet the challenges of manufacturing smart products, the manufacturing plants have been radically changed to become smart factories underpinned by industry 4.0 technologies. The transformation is assisted by employment of machine learning techniques that can deal with modeling both big or limited data. This manuscript reviews these concepts and present a case study that demonstrates the use of a novel intelligent hybrid algorithms for Industry 4.0 applications with limited data. In particular, an intelligent algorithm is proposed for robust data modeling of nonlinear systems based on input-output data. In our approach, a novel hybrid data-driven combining the Group-Method of Data-Handling and Singular-Value Decomposition is adapted to find an offline deterministic model combined with Pareto multi-objective optimization to overcome the overfitting issue. An Unscented-Kalman-Filter is also incorporated to update the coefficient of the deterministic model and increase its robustness against data uncertainties. The effectiveness of the proposed method is examined on a set of real industrial measurements.},
  language  = {en}
}
@article{KreyerMuellerEsch2020,
  author    = {Kreyer, J{\"o}rg and M{\"u}ller, Marvin and Esch, Thomas},
  title     = {A Calculation Methodology for Predicting Exhaust Mass Flows and Exhaust Temperature Profiles for Heavy-Duty Vehicles},
  series = {SAE International Journal of Commercial Vehicles},
  volume    = {13},
  journal   = {SAE International Journal of Commercial Vehicles},
  number    = {2},
  publisher = {SAE International},
  address   = {Warrendale, Pa.},
  issn      = {1946-3928},
  doi       = {10.4271/02-13-02-0009},
  pages     = {129 -- 143},
  year      = {2020},
  abstract  = {The predictive control of commercial vehicle energy management systems, such as vehicle thermal management or waste heat recovery (WHR) systems, are discussed on the basis of information sources from the field of environment recognition and in combination with the determination of the vehicle system condition. In this article, a mathematical method for predicting the exhaust gas mass flow and the exhaust gas temperature is presented based on driving data of a heavy-duty vehicle. The prediction refers to the conditions of the exhaust gas at the inlet of the exhaust gas recirculation (EGR) cooler and at the outlet of the exhaust gas aftertreatment system (EAT). The heavy-duty vehicle was operated on the motorway to investigate the characteristic operational profile. In addition to the use of road gradient profile data, an evaluation of the continuously recorded distance signal, which represents the distance between the test vehicle and the road user ahead, is included in the prediction model. Using a Fourier analysis, the trajectory of the vehicle speed is determined for a defined prediction horizon. To verify the method, a holistic simulation model consisting of several hierarchically structured submodels has been developed. A map-based submodel of a combustion engine is used to determine the EGR and EAT exhaust gas mass flows and exhaust gas temperature profiles. All simulation results are validated on the basis of the recorded vehicle and environmental data. Deviations from the predicted values are analyzed and discussed.},
  language  = {en}
}
@article{GoettenHavermannBraunetal.2020,
  author    = {G{\"o}tten, Falk and Havermann, Marc and Braun, Carsten and Marino, Matthew and Bil, Cees},
  title     = {Improved Form Factor for Drag Estimation of Fuselages with Various Cross Sections},
  series = {Journal of Aircraft},
  journal   = {Journal of Aircraft},
  publisher = {AIAA},
  address   = {Reston, Va.},
  issn      = {1533-3868},
  doi       = {10.2514/1.C036032},
  pages     = {1 -- 13},
  year      = {2020},
  abstract  = {The paper presents an aerodynamic investigation of 70 different streamlined bodies with fineness ratios ranging from 2 to 10. The bodies are chosen to idealize both unmanned and small manned aircraft fuselages and feature cross-sectional shapes that vary from circular to quadratic. The study focuses on friction and pressure drag in dependency of the individual body's fineness ratio and cross section. The drag forces are normalized with the respective body's wetted area to comply with an empirical drag estimation procedure. Although the friction drag coefficient then stays rather constant for all bodies, their pressure drag coefficients decrease with an increase in fineness ratio. Referring the pressure drag coefficient to the bodies' cross-sectional areas shows a distinct pressure drag minimum at a fineness ratio of about three. The pressure drag of bodies with a quadratic cross section is generally higher than for bodies of revolution. The results are used to derive an improved form factor that can be employed in a classic empirical drag estimation method. The improved formulation takes both the fineness ratio and cross-sectional shape into account. It shows superior accuracy in estimating streamlined body drag when compared with experimental data and other form factor formulations of the literature.},
  language  = {en}
}
@inproceedings{FingerGoettenBraunetal.2019,
  author    = {Finger, Felix and G{\"o}tten, Falk and Braun, Carsten and Bil, C.},
  title     = {On Aircraft Design Under the Consideration of Hybrid-Electric Propulsion Systems},
  series = {APISAT 2018: The Proceedings of the 2018 Asia-Pacific International Symposium on Aerospace Technology (APISAT 2018)},
  booktitle = {APISAT 2018: The Proceedings of the 2018 Asia-Pacific International Symposium on Aerospace Technology (APISAT 2018)},
  publisher = {Springer},
  address   = {Singapore},
  isbn      = {978-981-13-3305-7},
  doi       = {10.1007/978-981-13-3305-7_99},
  pages     = {1261 -- 1272},
  year      = {2019},
  abstract  = {A hybrid-electric propulsion system combines the advantages of fuel-based systems and battery powered systems and offers new design freedom. To take full advantage of this technology, aircraft designers must be aware of its key differences, compared to conventional, carbon-fuel based, propulsion systems. This paper gives an overview of the challenges and potential benefits associated with the design of aircraft that use hybrid-electric propulsion systems. It offers an introduction of the most popular hybrid-electric propulsion architectures and critically assess them against the conventional and fully electric propulsion configurations. The effects on operational aspects and design aspects are covered. Special consideration is given to the application of hybrid-electric propulsion technology to both unmanned and vertical take-off and landing aircraft. The authors conclude that electric propulsion technology has the potential to revolutionize aircraft design. However, new and innovative methods must be researched, to realize the full benefit of the technology.},
  language  = {en}
}
@inproceedings{GoettenFingerBraunetal.2019,
  author    = {G{\"o}tten, Falk and Finger, Felix and Braun, Carsten and Havermann, Marc and Bil, C. and Gomez, F.},
  title     = {Empirical Correlations for Geometry Build-Up of Fixed Wing Unmanned Air Vehicles},
  series = {APISAT 2018: The Proceedings of the 2018 Asia-Pacific International Symposium on Aerospace Technology (APISAT 2018)},
  booktitle = {APISAT 2018: The Proceedings of the 2018 Asia-Pacific International Symposium on Aerospace Technology (APISAT 2018)},
  publisher = {Springer},
  address   = {Singapore},
  isbn      = {978-981-13-3305-7},
  doi       = {10.1007/978-981-13-3305-7_109},
  pages     = {1365 -- 1381},
  year      = {2019},
  abstract  = {The results of a statistical investigation of 42 fixed-wing, small to medium sized (20 kg-1000 kg) reconnaissance unmanned air vehicles (UAVs) are presented. Regression analyses are used to identify correlations of the most relevant geometry dimensions with the UAV's maximum take-off mass. The findings allow an empirical based geometry-build up for a complete unmanned aircraft by referring to its take-off mass only. This provides a bridge between very early design stages (initial sizing) and the later determination of shapes and dimensions. The correlations might be integrated into a UAV sizing environment and allow designers to implement more sophisticated drag and weight estimation methods in this process. Additional information on correlation factors for a rough drag estimation methodology indicate how this technique can significantly enhance the accuracy of early design iterations.},
  language  = {en}
}
@article{GoettenFingerHavermannetal.2021,
  author    = {G{\"o}tten, Falk and Finger, Felix and Havermann, Marc and Braun, Carsten and Marino, M. and Bil, C.},
  title     = {Full configuration drag estimation of short-to-medium range fixed-wing UAVs and its impact on initial sizing optimization},
  series = {CEAS Aeronautical Journal},
  volume    = {12},
  journal   = {CEAS Aeronautical Journal},
  publisher = {Springer},
  address   = {Berlin},
  issn      = {1869-5590 (Online)},
  doi       = {10.1007/s13272-021-00522-w},
  pages     = {589 -- 603},
  year      = {2021},
  abstract  = {The paper presents the derivation of a new equivalent skin friction coefficient for estimating the parasitic drag of short-to-medium range fixed-wing unmanned aircraft. The new coefficient is derived from an aerodynamic analysis of ten different unmanned aircraft used for surveillance, reconnaissance, and search and rescue missions. The aircraft is simulated using a validated unsteady Reynolds-averaged Navier Stokes approach. The UAV's parasitic drag is significantly influenced by the presence of miscellaneous components like fixed landing gears or electro-optical sensor turrets. These components are responsible for almost half of an unmanned aircraft's total parasitic drag. The new equivalent skin friction coefficient accounts for these effects and is significantly higher compared to other aircraft categories. It is used to initially size an unmanned aircraft for a typical reconnaissance mission. The improved parasitic drag estimation yields a much heavier unmanned aircraft when compared to the sizing results using available drag data of manned aircraft.},
  language  = {en}
}
@inproceedings{ThomaFisherBraun2020,
  author    = {Thoma, Andreas and Fisher, Alex and Braun, Carsten},
  title     = {Improving the px4 avoid algorithm by bio-inspired flight strategies},
  series = {DLRK2020 - „Luft- und Raumfahrt - Verantwortung in allen Dimensionen"},
  booktitle = {DLRK2020 - „Luft- und Raumfahrt - Verantwortung in allen Dimensionen"},
  pages     = {10 Seiten},
  year      = {2020},
  language  = {en}
}
@inproceedings{HauggKreyerKemperetal.2020,
  author    = {Haugg, Albert Thomas and Kreyer, J{\"o}rg and Kemper, Hans and Hatesuer, Katerina and Esch, Thomas},
  title     = {Heat exchanger for ORC. adaptability and optimisation potentials},
  series = {IIR International Rankine 2020 Conference},
  booktitle = {IIR International Rankine 2020 Conference},
  doi       = {10.18462/iir.rankine.2020.1224},
  pages     = {10 Seiten},
  year      = {2020},
  abstract  = {The recovery of waste heat requires heat exchangers to extract it from a liquid or gaseous medium into another working medium, a refrigerant. In Organic Rankine Cycles (ORC) on Combustion Engines there are two major heat sources, the exhaust gas and the water/glycol fluid from the engine's cooling circuit. A heat exchanger design must be adapted to the different requirements and conditions resulting from the heat sources, fluids, system configurations, geometric restrictions, and etcetera. The Stacked Shell Cooler (SSC) is a new and very specific design of a plate heat exchanger, created by AKG, which allows with a maximum degree of freedom the optimization of heat exchange rate and the reduction of the related pressure drop. This optimization in heat exchanger design for ORC systems is even more important, because it reduces the energy consumption of the system and therefore maximizes the increase in overall efficiency of the engine.},
  language  = {en}
}
@inproceedings{FingerdeVriesVosetal.2020,
  author    = {Finger, Felix and de Vries, Reynard and Vos, Roelof and Braun, Carsten and Bil, Cees},
  title     = {A comparison of hybrid-electric aircraft sizing methods},
  series = {AIAA Scitech 2020 Forum},
  booktitle = {AIAA Scitech 2020 Forum},
  doi       = {10.2514/6.2020-1006},
  pages     = {31 Seiten},
  year      = {2020},
  language  = {en}
}
@inproceedings{KreyerMuellerEsch2020,
  author    = {Kreyer, J{\"o}rg and M{\"u}ller, Marvin and Esch, Thomas},
  title     = {A Map-Based Model for the Determination of Fuel Consumption for Internal Combustion Engines as a Function of Flight Altitude},
  series = {Deutscher Luft- und Raumfahrtkongress 2019, „Luft- und Raumfahrt - technologische Br{\"u}cke in die Zukunft", Darmstadt, 30. September bis 2. Oktober 2019},
  booktitle = {Deutscher Luft- und Raumfahrtkongress 2019, „Luft- und Raumfahrt - technologische Br{\"u}cke in die Zukunft", Darmstadt, 30. September bis 2. Oktober 2019},
  publisher = {Deutsche Gesellschaft f{\"u}r Luft- und Raumfahrt - Lilienthal-Oberth e.V},
  address   = {Bonn},
  doi       = {10.25967/490162},
  pages     = {13 Seiten},
  year      = {2020},
  language  = {en}
}
@inproceedings{ThomaFisherBertrandetal.2020,
  author    = {Thoma, Andreas and Fisher, Alex and Bertrand, Olivier and Braun, Carsten},
  title     = {Evaluation of possible flight strategies for close object evasion from bumblebee experiments},
  series = {Living Machines 2020: Biomimetic and Biohybrid Systems},
  booktitle = {Living Machines 2020: Biomimetic and Biohybrid Systems},
  editor    = {Vouloutsi, Vasiliki and Mura, Anna and Tauber, Falk and Speck, Thomas and Prescott, Tony J. and Verschure, Paul F. M. J.},
  publisher = {Springer},
  address   = {Cham},
  isbn      = {978-3-030-64312-6},
  doi       = {10.1007/978-3-030-64313-3_34},
  pages     = {354 -- 365},
  year      = {2020},
  language  = {en}
}
@article{Schueckhaus2020,
  author    = {Sch{\"u}ckhaus, Ulrich},
  title     = {Die SkyCab-Erfinder im WFMG-Interview},
  series = {Business in MG},
  journal   = {Business in MG},
  number    = {1},
  pages     = {6 -- 7},
  year      = {2020},
  language  = {de}
}
@article{FunkeEschRoosen2022,
  author    = {Funke, Harald and Esch, Thomas and Roosen, Petra},
  title     = {Powertrain Adaptions for LPG Usage in General Aviation},
  series = {MTZ worldwide},
  volume    = {2022},
  journal   = {MTZ worldwide},
  number    = {83},
  publisher = {Springer Nature},
  address   = {Basel},
  doi       = {10.1007/s38313-021-0756-6},
  pages     = {58 -- 62},
  year      = {2022},
  abstract  = {In general aviation, too, it is desirable to be able to operate existing internal combustion engines with fuels that produce less CO₂ than Avgas 100LL being widely used today It can be assumed that, in comparison, the fuels CNG, LPG or LNG, which are gaseous under normal conditions, produce significantly lower emissions. Necessary propulsion system adaptations were investigated as part of a research project at Aachen University of Applied Sciences.},
  language  = {en}
}
@article{LaarmannThomaMischetal.2023,
  author    = {Laarmann, Lukas and Thoma, Andreas and Misch, Philipp and R{\"o}th, Thilo and Braun, Carsten and Watkins, Simon and Fard, Mohammad},
  title     = {Automotive safety approach for future eVTOL vehicles},
  series = {CEAS Aeronautical Journal},
  journal   = {CEAS Aeronautical Journal},
  publisher = {Springer Nature},
  issn      = {1869-5590 (Online)},
  doi       = {10.1007/s13272-023-00655-0},
  pages     = {11 Seiten},
  year      = {2023},
  abstract  = {The eVTOL industry is a rapidly growing mass market expected to start in 2024. eVTOL compete, caused by their predicted missions, with ground-based transportation modes, including mainly passenger cars. Therefore, the automotive and classical aircraft design process is reviewed and compared to highlight advantages for eVTOL development. A special focus is on ergonomic comfort and safety. The need for further investigation of eVTOL's crashworthiness is outlined by, first, specifying the relevance of passive safety via accident statistics and customer perception analysis; second, comparing the current state of regulation and certification; and third, discussing the advantages of integral safety and applying the automotive safety approach for eVTOL development. Integral safety links active and passive safety, while the automotive safety approach means implementing standardized mandatory full-vehicle crash tests for future eVTOL. Subsequently, possible crash impact conditions are analyzed, and three full-vehicle crash load cases are presented.},
  language  = {en}
}
@misc{EickmannEschFunkeetal.2014,
  author    = {Eickmann, Matthias and Esch, Thomas and Funke, Harald and Abanteriba, Sylvester and Roosen, Petra},
  title     = {Biofuels in Aviation - Safety Implications of Bio-Ethanol Usage in General Aviation Aircraft},
  year      = {2014},
  abstract  = {Up in the clouds and above fuels and construction materials must be very carefully selected to ensure a smooth flight and touchdown. Out of around 38,000 single and dual-engined propeller aeroplanes, roughly a third are affected by a new trend in the fuel sector that may lead to operating troubles or even emergency landings: The admixture of bio-ethanol to conventional gasoline. Experiences with these fuels may be projected to alternative mixtures containing new components.},
  language  = {en}
}
@article{SchulzeFeyerlPischinger2023,
  author    = {Schulze, Sven and Feyerl, G{\"u}nter and Pischinger, Stefan},
  title     = {Advanced ECMS for hybrid electric heavy-duty trucks with predictive battery discharge and adaptive operating strategy under real driving conditions},
  series = {Energies},
  volume    = {16},
  journal   = {Energies},
  number    = {13},
  publisher = {MDPI},
  address   = {Basel},
  issn      = {1996-1073},
  doi       = {10.3390/en16135171},
  pages     = {29 Seiten, Art. Nr.: 5171},
  year      = {2023},
  abstract  = {To fulfil the CO2 emission reduction targets of the European Union (EU), heavy-duty (HD) trucks need to operate 15\% more efficiently by 2025 and 30\% by 2030. Their electrification is necessary as conventional HD trucks are already optimized for the long-haul application. The resulting hybrid electric vehicle (HEV) truck gains most of the fuel saving potential by the recuperation of potential energy and its consecutive utilization. The key to utilizing the full potential of HEV-HD trucks is to maximize the amount of recuperated energy and ensure its intelligent usage while keeping the operating point of the internal combustion engine as efficient as possible. To achieve this goal, an intelligent energy management strategy (EMS) based on ECMS is developed for a parallel HEV-HD truck which uses predictive discharge of the battery and adaptive operating strategy regarding the height profile and the vehicle mass. The presented EMS can reproduce the global optimal operating strategy over long phases and lead to a fuel saving potential of up to 2\% compared with a heuristic strategy. Furthermore, the fuel saving potential is correlated with the investigated boundary conditions to deepen the understanding of the impact of intelligent EMS for HEV-HD trucks.},
  language  = {en}
}
@misc{SchmitzSchebitzEsch1997,
  author    = {Schmitz, G{\"u}nter and Schebitz, Michael and Esch, Thomas},
  title     = {Aus der Ruhelage selbstanziehender elektromagnetischer Aktuator},
  year      = {1997},
  abstract  = {Elektromagnetischer Aktuator zur Bet{\"a}tigung eines Stellgliedes (2), mit wenigstens einem Elektromagneten (4) und einem mit dem Stellglied (2) verbundenen Anker (3), der gegen die Kraft einer R{\"u}ckstellfeder (6) aus seiner Ruhelage in Richtung auf den Elektromagneten (4) bewegbar ist, mit einer R{\"u}ckstellfeder (6), die eine nicht lineare, bezogen auf die Ruhelage des Ankers (3) progressiv ansteigende Kennlinie aufweist.},
  language  = {de}
}
@misc{SalberPischingerEschetal.1998,
  author    = {Salber, Wolfgang and Pischinger, Martin and Esch, Thomas and Hagen, J{\"u}rgen},
  title     = {Kaltstartverfahren f{\"u}r eine drosselfreie Mehrzylinder-Kolbenbrennkraftmaschine},
  year      = {1998},
  abstract  = {Die Erfindung betrifft ein Kaltstartverfahren f{\"u}r eine Mehrzylinder-Kolbenbrennkraftmaschine mit Anlasser und einer Motorsteuerung zur Ansteuerung von Kraftstoffeinspritzeinrichtungen, Z{\"u}ndung und voll variabel elektromagnetisch bet{\"a}tigbaren Gaswechselventilen an den einzelnen Zylindern, bei dem die Kurbelwelle {\"u}ber den Anlasser gedreht wird und zum Start f{\"u}r wenigstens einen Zylinder die dazugeh{\"o}rigen Gaswechselventile, die Kraftstoffeinspritzeinrichtung und die Z{\"u}ndung in einem vorgegebenen Taktzyklus angesteuert werden und zwar in den ersten Arbeitszyklen mit "Sp{\"a}tem Einlaß {\"O}ffnen".},
  language  = {de}
}
@inproceedings{SchopenShabaniEschetal.2022,
  author    = {Schopen, Oliver and Shabani, Bahman and Esch, Thomas and Kemper, Hans and Shah, Neel},
  title     = {Quantitative evaluation of health management designs for fuel cell systems in transport vehicles},
  series = {2nd UNITED-SAIG International Conference Proceedings},
  booktitle = {2nd UNITED-SAIG International Conference Proceedings},
  editor    = {Rahim, S.A. and As'arry, A. and Zuhri, M.Y.M. and Harmin, M.Y. and Rezali, K.A.M. and Hairuddin, A.A.},
  pages     = {1 -- 3},
  year      = {2022},
  abstract  = {Focusing on transport vehicles, mainly with regard to aviation applications, this paper presents compilation and subsequent quantitative evaluation of methods aimed at building an optimum integrated health management solution for fuel cell systems. The methods are divided into two different main types and compiled in a related scheme. Furthermore, different methods are analysed and evaluated based on parameters specific to the aviation context of this study. Finally, the most suitable method for use in fuel cell health management systems is identified and its performance and suitability is quantified.},
  language  = {en}
}
@inproceedings{SchopenKemperEsch2021,
  author    = {Schopen, Oliver and Kemper, Hans and Esch, Thomas},
  title     = {Development of a comparison methodology and evaluation matrix for electrically driven compressors in ICE and FC},
  series = {Proceedings of the 1st UNITED - Southeast Asia Automotive Interest Group (SAIG) International Conference},
  booktitle = {Proceedings of the 1st UNITED - Southeast Asia Automotive Interest Group (SAIG) International Conference},
  publisher = {FH Joanneum},
  address   = {Graz},
  isbn      = {978-3-902103-94-9},
  pages     = {45 -- 46},
  year      = {2021},
  abstract  = {In addition to electromobility and alternative drive systems, a focus is set on electrically driven compressors (EDC), with a high potential for increasing the efficiency of internal combustion engines (ICE) and fuel cells [01]. The primary objective is to increase the ICE torque, provided independently of the ICE speed by compressing the intake air and consequently the ICE filling level supported by the compressor. For operation independent from the ICE speed, the EDC compressor is decoupled from the turbine by using an electric compressor motor (CM) instead of the turbine. ICE performances can be increased by the use of EDC where individual compressor parameters are adapted to the respective application area [02] [03]. This task contains great challenges, increased by demands with regard to pollutant reduction while maintaining constant performance and reduced fuel consumption. The FH-Aachen is equipped with an EDC test bench which enables EDC-investigations in various configurations and operating modes. Characteristic properties of different compressors can be determined, which build the basis for a comparison methodology. Subject of this project is the development of a comparison methodology for EDC with an associated evaluation method and a defined overall evaluation method. For the application of this comparison methodology, corresponding series of measurements are carried out on the EDC test bench using an appropriate test device.},
  language  = {en}
}
@inproceedings{VeettilRakshitSchopenetal.2022,
  author    = {Veettil, Yadu Krishna Morassery and Rakshit, Shantam and Schopen, Oliver and Kemper, Hans and Esch, Thomas and Shabani, Bahman},
  title     = {Automated Control System Strategies to Ensure Safety of PEM Fuel Cells Using Kalman Filters},
  series = {Proceedings of the 7th International Conference and Exhibition on Sustainable Energy and Advanced Materials (ICE-SEAM 2021), Melaka, Malaysia},
  booktitle = {Proceedings of the 7th International Conference and Exhibition on Sustainable Energy and Advanced Materials (ICE-SEAM 2021), Melaka, Malaysia},
  editor    = {Bin Abdollah, Mohd Fadzli and Amiruddin, Hilmi and Singh, Amrik Singh Phuman and Munir, Fudhail Abdul and Ibrahim, Asriana},
  publisher = {Springer Nature},
  address   = {Singapore},
  isbn      = {978-981-19-3178-9},
  issn      = {2195-4356},
  doi       = {10.1007/978-981-19-3179-6_55},
  pages     = {296 -- 299},
  year      = {2022},
  abstract  = {Having well-defined control strategies for fuel cells, that can efficiently detect errors and take corrective action is critically important for safety in all applications, and especially so in aviation. The algorithms not only ensure operator safety by monitoring the fuel cell and connected components, but also contribute to extending the health of the fuel cell, its durability and safe operation over its lifetime. While sensors are used to provide peripheral data surrounding the fuel cell, the internal states of the fuel cell cannot be directly measured. To overcome this restriction, Kalman Filter has been implemented as an internal state observer. Other safety conditions are evaluated using real-time data from every connected sensor and corrective actions automatically take place to ensure safety. The algorithms discussed in this paper have been validated thorough Model-in-the-Loop (MiL) tests as well as practical validation at a dedicated test bench.},
  language  = {en}
}
@inproceedings{TamaldinMansorMatYaminetal.2022,
  author    = {Tamaldin, Noreffendy and Mansor, Muhd Rizuan and Mat Yamin, Ahmad Kamal and Bin Abdollah, Mohd Fazli and Esch, Thomas and Tonoli, Andrea and Reisinger, Karl Heinz and Sprenger, Hanna and Razuli, Hisham},
  title     = {Development of UTeM United Future Fuel Design Training Center Under Erasmus+ United Program},
  series = {Proceedings of the 7th International Conference and Exhibition on Sustainable Energy and Advanced Materials (ICE-SEAM 2021), Melaka, Malaysia},
  booktitle = {Proceedings of the 7th International Conference and Exhibition on Sustainable Energy and Advanced Materials (ICE-SEAM 2021), Melaka, Malaysia},
  editor    = {Bin Abdollah, Mohd Fadzli and Amiruddin, Hilmi and Singh, Amrik Singh Phuman and Munir, Fudhail Abdul and Ibrahim, Asriana},
  publisher = {Springer Nature},
  address   = {Singapore},
  isbn      = {978-981-19-3178-9},
  issn      = {2195-4356},
  doi       = {10.1007/978-981-19-3179-6_50},
  pages     = {274 -- 278},
  year      = {2022},
  abstract  = {The industrial revolution IR4.0 era have driven many states of the art technologies to be introduced especially in the automotive industry. The rapid development of automotive industries in Europe have created wide industry gap between European Union (EU) and developing countries such as in South-East Asia (SEA). Indulging this situation, FH Joanneum, Austria together with European partners from FH Aachen, Germany and Politecnico Di Torino, Italy is taking initiative to close the gap utilizing the Erasmus+ United grant from EU. A consortium was founded to engage with automotive technology transfer using the European ramework to Malaysian, Indonesian and Thailand Higher Education Institutions (HEI) as well as automotive industries. This could be achieved by establishing Engineering Knowledge Transfer Unit (EKTU) in respective SEA institutions guided by the industry partners in their respective countries. This EKTU could offer updated, innovative, and high-quality training courses to increase graduate's employability in higher education institutions and strengthen relations between HEI and the wider economic and social environment by addressing Universityindustry cooperation which is the regional priority for Asia. It is expected that, the Capacity Building Initiative would improve the quality of higher education and enhancing its relevance for the labor market and society in the SEA partners. The outcome of this project would greatly benefit the partners in strong and complementary partnership targeting the automotive industry and enhanced larger scale international cooperation between the European and SEA partners. It would also prepare the SEA HEI in sustainable partnership with Automotive industry in the region as a mean of income generation in the future.},
  language  = {en}
}
@inproceedings{TamaldinEschTonolietal.2020,
  author    = {Tamaldin, Noreffendy and Esch, Thomas and Tonoli, Andrea and Reisinger, Karl Heinz and Sprenger, Hanna and Razuli, Hisham},
  title     = {ERASMUS+ United CBHE Automotive International Collaboration from European to South East Asia},
  series = {Proceedings of the 2nd African International Conference on Industrial Engineering and Operations Management},
  booktitle = {Proceedings of the 2nd African International Conference on Industrial Engineering and Operations Management},
  publisher = {IEOM Society International},
  address   = {Southfield},
  isbn      = {978-1-7923-6123-4},
  issn      = {2169-8767},
  pages     = {2970 -- 2972},
  year      = {2020},
  abstract  = {The industrial revolution especially in the IR4.0 era have driven many states of the art technologies to be introduced. The automotive industry as well as many other key industries have also been greatly influenced. The rapid development of automotive industries in Europe have created wide industry gap between European Union (EU) and developing countries such as in South East Asia (SEA). Indulging this situation, FH JOANNEUM, Austria together with European partners from FH Aachen, Germany and Politecnico di Torino, Italy are taking initiative to close down the gap utilizing the Erasmus+ United Capacity Building in Higher Education grant from EU. A consortium was founded to engage with automotive technology transfer using the European framework to Malaysian, Indonesian and Thailand Higher Education Institutions (HEI) as well as automotive industries in respective countries. This could be achieved by establishing Engineering Knowledge Transfer Unit (EKTU) in respective SEA institutions guided by the industry partners in their respective countries. This EKTU could offer updated, innovative and high-quality training courses to increase graduate's employability in higher education institutions and strengthen relations between HEI and the wider economic and social environment by addressing University-industry cooperation which is the regional priority for Asia. It is expected that, the Capacity Building Initiative would improve the quality of higher education and enhancing its relevance for the labor market and society in the SEA partners. The outcome of this project would greatly benefit the partners in strong and complementary partnership targeting the automotive industry and enhanced larger scale international cooperation between the European and SEA partners. It would also prepare the SEA HEI in sustainable partnership with Automotive industry in the region as a mean of income generation in the future.},
  language  = {en}
}
@inproceedings{KreyerEsch2017,
  author    = {Kreyer, J{\"o}rg and Esch, Thomas},
  title     = {Simulation Tool for Predictive Control Strategies for an ORCSystem in Heavy Duty Vehicles},
  series = {European GT Conference 2017},
  booktitle = {European GT Conference 2017},
  pages     = {16 Seiten},
  year      = {2017},
  abstract  = {Scientific questions - How can a non-stationary heat offering in the commercial vehicle be used to reduce fuel consumption? - Which potentials offer route and environmental information among with predicted speed and load trajectories to increase the efficiency of a ORC-System? Methods - Desktop bound holistic simulation model for a heavy duty truck incl. an ORC System - Prediction of massflows, temperatures and mixture quality (AFR) of exhaust gas},
  language  = {en}
}
@techreport{EschFunkeRoosen2010,
  author    = {Esch, Thomas and Funke, Harald and Roosen, Petra},
  title     = {SIoBiA - Safety Implications of Biofuels in Aviation},
  publisher = {EASA},
  address   = {K{\"o}ln},
  pages     = {279 Seiten},
  year      = {2010},
  abstract  = {Biofuels potentially interesting also for aviation purposes are predominantly liquid fuels produced from biomass. The most common biofuels today are biodiesel and bioethanol. Since diesel engines are rather rare in aviation this survey is focusing on ethanol admixed to gasoline products. The Directive 2003/30/EC of the European Parliament and the Council of May 8th 2003 on the promotion of the use of biofuels or other renewable fuels for transport encourage a growing admixture of biogenic fuel components to fossil automotive gasoline. Some aircraft models equipped with spark ignited piston engines are approved for operation with automotive gasoline, frequently called "MOGAS" (motor gasoline). The majority of those approvals is limited to MOGAS compositions that do not contain methanol or ethanol beyond negligible amounts. In the past years (bio-)MTBE or (bio-)ETBE have been widely used as blending component of automotive gasoline whilst the usage of low-molecular alcohols like methanol or ethanol has been avoided due to the handling problems especially with regard to the strong affinity for water. With rising mandatory bio-admixtures the conversion of the basic biogenic ethanol to ETBE, causing a reduction of energetic payoff, becomes more and more unattractive. Therefore the direct ethanol admixture is accordingly favoured. Due to the national enforcements of the directive 2003/30/EC more oxygenates produced from organic materials like bioethanol have started to appear in automotive gasolines already. The current fuel specification EN 228 already allows up to 3 \% volume per volume (v/v) (bio-)methanol or up to 5 \% v/v (bio-)ethanol as fuel components. This is also roughly the amount of biogenic components to comply with the legal requirements to avoid monetary penalties for producers and distributors of fuels. Since automotive fuel is cheaper than the common aviation gasoline (AVGAS), creates less problems with lead deposits in the engine, and in general produces less pollutants it is strongly favoured by pilots. But being designed for a different set of usage scenarios the use of automotive fuel with low molecular alcohols for aircraft operation may have adverse effects in aviation operation. Increasing amounts of ethanol admixtures impose various changes in the gasoline's chemical and physical properties, some of them rather unexpected and not within the range of flight experiences even of long-term pilots.},
  language  = {en}
}
@article{Esch2010,
  author    = {Esch, Thomas},
  title     = {Trends in commercial vehicle powertrains},
  series = {ATZautotechnology},
  volume    = {2010},
  journal   = {ATZautotechnology},
  number    = {10},
  publisher = {Vieweg \& Sohn},
  address   = {Wiesbaden},
  issn      = {2192-886X},
  doi       = {10.1007/BF03247185},
  pages     = {26 -- 31},
  year      = {2010},
  abstract  = {Low emission zones and truck bans, the rising price of diesel and increases in road tolls: all of these factors are putting serious pressure on the transport industry. Commercial vehicle manufacturers and their suppliers are in the process of identifying new solutions to these challenges as part of their efforts to meet the EEV (enhanced environmentally friendly vehicle) limits, which are currently the most robust European exhaust and emissions standards for trucks and buses.},
  language  = {en}
}
@inproceedings{KemperHellenbroichEsch2009,
  author    = {Kemper, Hans and Hellenbroich, Gereon and Esch, Thomas},
  title     = {Concept of an innovative passenger-car hybrid drive for European driving conditions},
  series = {Hybrid vehicles and energy management : 6th symposium ; 18th and 19th February 2009, Stadthalle Braunschweig},
  booktitle = {Hybrid vehicles and energy management : 6th symposium ; 18th and 19th February 2009, Stadthalle Braunschweig},
  publisher = {Gesamtzentrum f{\"u}r Verkehr (GZVB)},
  address   = {Braunschweig},
  isbn      = {978-3-937655-20-8},
  pages     = {264 -- 287},
  year      = {2009},
  abstract  = {The downsizing of spark ignition engines in conjunction with turbocharging is considered to be a promising method for reducing CO₂ emissions. Using this concept, FEV has developed a new, highly efficient drivetrain to demonstrate fuel consumption reduction and drivability in a vehicle based on the Ford Focus ST. The newly designed 1.8L turbocharged gasoline engine incorporates infinitely variable intake and outlet control timing and direct fuel injection utilizing piezo injectors centrally located. In addition, this engine uses a prototype FEV engine control system, with software that was developed and adapted entirely by FEV. The vehicle features a 160 kW engine with a maximum mean effective pressure of 22.4 bar and 34 \% savings in simulated fuel consumption. During the first stage, a new electrohydraulically actuated hybrid transmission with seven forward gears and one reverse gear and a single dry starting clutch will be integrated. The electric motor of the hybrid is directly connected to the gear set of the transmission. Utilizing the special gear set layout, the electric motor can provide boost during a change of gears, so that there is no interruption in traction. Therefore, the transmission system combines the advantages of a double clutch controlled gear change (gear change without an interruption in traction) with the efficient, cost-effective design of an automated manual transmission system. Additionally, the transmission provides a purely electric drive system and the operation of an air-conditioning compressor during the engine stop phases. One other alternative is through the use of CAI (Controlled Auto Ignition), which incorporates a process developed by FEV for controlled compression ignition.},
  language  = {en}
}
@inproceedings{FunkeEschRoosen2009,
  author    = {Funke, Harald and Esch, Thomas and Roosen, Peter},
  title     = {Using motor gasoline for aircrafts - coping with growing bio-fuel-caused risks by understanding cause-effect relationship},
  series = {Fuels 2009 : mineral oil based and alternative fuels ; 7th international colloquium ; January 14 - 15, 2009},
  booktitle = {Fuels 2009 : mineral oil based and alternative fuels ; 7th international colloquium ; January 14 - 15, 2009},
  editor    = {Bartz, Wilfried J.},
  publisher = {Technische Akademie Esslingen (TAE)},
  address   = {Ostfildern},
  isbn      = {978-3-924813-75-8},
  pages     = {237 -- 244},
  year      = {2009},
  abstract  = {The utilisation of vehicle-oriented gasoline in general aviation is very desirable for both ecological and economical reasons, as well as for general considerations of availability. As of today vehicle fuels may be used if the respective engine and cell are certified for such an operation. For older planes a supplementary technical certificate is provided for gasoline mixtures with less than 1 \% v/v ethanol only, though. Larger admixtures of ethanol may lead to sudden engine malfunction and should be considered as considerable security risks. Major problems are caused by the partially ethanol non-withstanding materials, a necessarily changed stochiometric adjustment of the engine for varying ethanol shares and the tendency for phase separation in the presence of absorbed water. The concepts of the flexible fuel vehicles are only partially applicable in the view of air security.},
  language  = {en}
}
@inproceedings{WeissAbanteribaEsch2007,
  author    = {Weiss, Alexander and Abanteriba, Sylvester and Esch, Thomas},
  title     = {Investigation of Flow Separation Inside a Conical Rocket Nozzle With the Aid of an Annular Cross Flow},
  series = {Proceedings of the ASME/JSME 2007 5th Joint Fluids Engineering Conference. Volume 1: Symposia, Parts A and B},
  booktitle = {Proceedings of the ASME/JSME 2007 5th Joint Fluids Engineering Conference. Volume 1: Symposia, Parts A and B},
  publisher = {American Society of Mechanical Engineers (ASME)},
  address   = {New York},
  isbn      = {0-7918-4288-6},
  doi       = {10.1115/FEDSM2007-37387},
  pages     = {1861 -- 1871},
  year      = {2007},
  abstract  = {Flow separation is a phenomenon that occurs in all kinds of supersonic nozzles sometimes during run-up and shut-down operations. Especially in expansion nozzles of rocket engines with large area ratio, flow separation can trigger strong side loads that can damage the structure of the nozzle. The investigation presented in this paper seeks to establish measures that may be applied to alter the point of flow separation. In order to achieve this, a supersonic nozzle was placed at the exit plane of the conical nozzle. This resulted in the generation of cross flow surrounding the core jet flow from the conical nozzle. Due to the entrainment of the gas stream from the conical nozzle the pressure in its exit plane was found to be lower than that of the ambient. A Cold gas instead of hot combustion gases was used as the working fluid. A mathematical simulation of the concept was validated by experiment. Measurements confirmed the simulation results that due to the introduction of a second nozzle the pressure in the separated region of the conical nozzle was significantly reduced. It was also established that the boundary layer separation inside the conical nozzle was delayed thus allowing an increased degree of overexpansion. The condition established by the pressure measurements was also demonstrated qualitatively using transparent nozzle configurations.},
  language  = {en}
}
@misc{PischingerEschDuesmann2006,
  author    = {Pischinger, Martin and Esch, Thomas and Duesmann, Klaus},
  title     = {Elektromagnetischer Aktuator mit gelenkig abgest{\"u}tzter R{\"u}ckstellfeder},
  year      = {2006},
  abstract  = {Die Erfindung betrifft einen elektromagnetischen Aktuator zur Bet{\"a}tigung eines Stellgliedes (7) mit wenigstens einem gesteuert bestrombaren Elektromagneten (1, 2) und einem mit dem Stellglied (7) in Wirkverbindung stehenden Anker (5), der bei Bestromung des Elektromagneten (1, 2) gegen die Kraft wenigstens einer an einem Geh{\"a}use (12) abgest{\"u}tzten R{\"u}ckstellfeder (10) an der Polfl{\"a}che (3, 4) des Elektromagneten (1, 2) zur Anlage kommt, und daß zumindest der Anker (5) {\"u}ber eine sph{\"a}rische Gelenkanordnung (11) auf der R{\"u}ckstellfeder (10) abgest{\"u}tzt ist.},
  language  = {de}
}
@inproceedings{HuthElsenHartwigetal.2006,
  author    = {Huth, Thomas and Elsen, Olaf and Hartwig, Christoph and Esch, Thomas},
  title     = {Innovative modular valve trains for 2015 - logistic benefits by EMVT},
  series = {IFAC Proceedings Volumes, Volume 39, Issue 3},
  booktitle = {IFAC Proceedings Volumes, Volume 39, Issue 3},
  publisher = {Elsevier},
  address   = {Amsterdam},
  doi       = {10.3182/20060517-3-FR-2903.00172},
  pages     = {315 -- 320},
  year      = {2006},
  abstract  = {In this paper the way to a 5-day-car with respect to a modular valve train systems for spark ignited combustion engines is shown. The necessary product diversity is shift from mechanical or physical components to software components. Therefore, significant improvements of logistic indicators are expected and shown. The working principle of a camless cylinder head with respect to an electromagnetical valve train (EMVT) is explained and it is demonstrated that shifting physical diversity to software is feasible. The future design of combustion engine systems including customisation can be supported by a set of assistance tools which is shown exemplary.},
  language  = {en}
}
@article{FunkeEschRoosen2022,
  author    = {Funke, Harald and Esch, Thomas and Roosen, Petra},
  title     = {Antriebssystemanpassungen zur Verwendung von LPG als Flugkraftstoff},
  series = {Motortechnische Zeitschrift (MTZ)},
  volume    = {2022},
  journal   = {Motortechnische Zeitschrift (MTZ)},
  number    = {83},
  publisher = {Springer Nature},
  address   = {Basel},
  doi       = {10.1007/s35146-021-0778-2},
  pages     = {58 -- 62},
  year      = {2022},
  abstract  = {Auch in der allgemeinen Luftfahrt w{\"a}re es w{\"u}nschenswert, die bereits vorhandenen Verbrennungsmotoren mit weniger CO₂-tr{\"a}chtigen Kraftstoffen als dem heute weit verbreiteten Avgas 100LL betreiben zu k{\"o}nnen. Es ist anzunehmen, dass im Vergleich die unter Normalbedingungen gasf{\"o}rmigen Kraftstoffe CNG, LPG oder LNG deutlich weniger Emissionen produzieren. Erforderliche Antriebssystemanpassungen wurden im Rahmen eines Forschungsprojekts an der FH Aachen untersucht.},
  language  = {de}
}
@article{FayyaziSardarThomasetal.2023,
  author    = {Fayyazi, Mojgan and Sardar, Paramjotsingh and Thomas, Sumit Infent and Daghigh, Roonak and Jamali, Ali and Esch, Thomas and Kemper, Hans and Langari, Reza and Khayyam, Hamid},
  title     = {Artificial intelligence/machine learning in energy management systems, control, and optimization of hydrogen fuel cell vehicles},
  volume    = {15},
  number    = {6},
  publisher = {MDPI},
  address   = {Basel},
  doi       = {10.3390/su15065249},
  pages     = {38},
  year      = {2023},
  abstract  = {Environmental emissions, global warming, and energy-related concerns have accelerated the advancements in conventional vehicles that primarily use internal combustion engines. Among the existing technologies, hydrogen fuel cell electric vehicles and fuel cell hybrid electric vehicles may have minimal contributions to greenhouse gas emissions and thus are the prime choices for environmental concerns. However, energy management in fuel cell electric vehicles and fuel cell hybrid electric vehicles is a major challenge. Appropriate control strategies should be used for effective energy management in these vehicles. On the other hand, there has been significant progress in artificial intelligence, machine learning, and designing data-driven intelligent controllers. These techniques have found much attention within the community, and state-of-the-art energy management technologies have been developed based on them. This manuscript reviews the application of machine learning and intelligent controllers for prediction, control, energy management, and vehicle to everything (V2X) in hydrogen fuel cell vehicles. The effectiveness of data-driven control and optimization systems are investigated to evolve, classify, and compare, and future trends and directions for sustainability are discussed.},
  language  = {en}
}
@book{JanserHavermannHoeveleretal.2023,
  author    = {Janser, Frank and Havermann, Marc and Hoeveler, Bastian and Hertz, Cyril and Bergmann, Ole},
  title     = {Str{\"o}mungslehre und Aerodynamik : inkompressible Profile und Tragfl{\"u}gelaerodynamik, Band 2},
  edition   = {4. Auflage},
  publisher = {Mainz},
  address   = {Aachen},
  isbn      = {978-3-8107-0261-6},
  pages     = {XIII, 211 Seiten},
  year      = {2023},
  abstract  = {Das vorliegende Buch dient als Grundlage f{\"u}r die Bachelor- und Master-Ausbildung von Studierenden im Fachgebiet Str{\"o}mungslehre und Aerodynamik. Im hier behandelten Teilbereich der inkompressiblen Profile und Tragfl{\"u}gelaerodynamik werden schwerpunktm{\"a}ßig die folgenden Themen besprochen: - Profilaerodynamik - Tragfl{\"u}gelaerodynamik - Flugzeugpolare - Methoden zur Flugbereichserweiterung - Schwebeschub und Schwebeleistung - Propellerblattaerodynamik - Numerische Methoden zur Tragfl{\"u}gelberechnung},
  language  = {de}
}
@article{ThomaThomessenGardietal.2023,
  author    = {Thoma, Andreas and Thomessen, Karolin and Gardi, Alessandro and Fisher, A. and Braun, Carsten},
  title     = {Prioritising paths: An improved cost function for local path planning for UAV in medical applications},
  series = {The Aeronautical Journal},
  journal   = {The Aeronautical Journal},
  number    = {First View},
  publisher = {Cambridge University Press},
  address   = {Cambridge},
  issn      = {0001-9240 (Print)},
  doi       = {10.1017/aer.2023.68},
  pages     = {1 -- 18},
  year      = {2023},
  abstract  = {Even the shortest flight through unknown, cluttered environments requires reliable local path planning algorithms to avoid unforeseen obstacles. The algorithm must evaluate alternative flight paths and identify the best path if an obstacle blocks its way. Commonly, weighted sums are used here. This work shows that weighted Chebyshev distances and factorial achievement scalarising functions are suitable alternatives to weighted sums if combined with the 3DVFH* local path planning algorithm. Both methods considerably reduce the failure probability of simulated flights in various environments. The standard 3DVFH* uses a weighted sum and has a failure probability of 50\% in the test environments. A factorial achievement scalarising function, which minimises the worst combination of two out of four objective functions, reaches a failure probability of 26\%; A weighted Chebyshev distance, which optimises the worst objective, has a failure probability of 30\%. These results show promise for further enhancements and to support broader applicability.},
  language  = {en}
}
@incollection{HeimesKampkerKehreretal.2023,
  author    = {Heimes, Heiner Hans and Kampker, Achim and Kehrer, Mario and D{\"u}nnwald, Simon and Heetfeld, Lennart and Polzenberg, Jens and Budde, Lucas and Keusen, Maximilian and Pandey, Rahul and R{\"o}th, Thilo},
  title     = {Fahrzeugstruktur},
  series = {Elektromobilit{\"a}t: Grundlagen einer Fortschrittstechnologie},
  booktitle = {Elektromobilit{\"a}t: Grundlagen einer Fortschrittstechnologie},
  editor    = {Kampker, Achim and Heimes, Heiner Hans},
  publisher = {Springer Vieweg},
  address   = {Berlin},
  isbn      = {978-3-662-65811-6 (Print)},
  doi       = {10.1007/978-3-662-65812-3_5},
  pages     = {69 -- 106},
  year      = {2023},
  abstract  = {Um sowohl Treibhausgas-Emissionen zu verringern als auch Kraftstoffressourcen zu schonen, wird zunehmend an einer Transformation konventionell angetriebener Kraftfahrzeuge hin zu elektrifizierten Antriebskonzepten gearbeitet. Basierend auf herk{\"o}mmlichen Fahrzeugen mit Verbrennungsmotor wurde eine Vielzahl neuer Antriebssysteme mit verschiedenem Elektrifizierungsgrad entwickelt. Mitte der 1990er-Jahre kamen erste Fahrzeuge mit einem Hybridantrieb auf den Markt. Die Kombination aus Verbrennungs- und Elektromotor erlaubt eine Verbrauchsreduktion und Bremsenergier{\"u}ckgewinnung sowie lokal emissionsfreies Fahren.},
  language  = {de}
}
@incollection{HeimesKampkerDornetal.2023,
  author    = {Heimes, Heiner Hans and Kampker, Achim and Dorn, Benjamin and Kehrer, Mario and D{\"u}nnwald, Simon and Badura, Dennis and Terren, Maximilian and R{\"o}th, Thilo},
  title     = {Produktionsprozesse der Fahrzeugstruktur},
  series = {Elektromobilit{\"a}t: Grundlagen einer Fortschrittstechnologie},
  booktitle = {Elektromobilit{\"a}t: Grundlagen einer Fortschrittstechnologie},
  editor    = {Kampker, Achim and Heimes, Heiner Hans},
  publisher = {Springer Vieweg},
  address   = {Berlin},
  isbn      = {978-3-662-65811-6 (Print)},
  doi       = {10.1007/978-3-662-65812-3_13},
  pages     = {227 -- 247},
  year      = {2023},
  language  = {de}
}
@article{ThomessenThomaBraun2023,
  author    = {Thomessen, Karolin and Thoma, Andreas and Braun, Carsten},
  title     = {Bio-inspired altitude changing extension to the 3DVFH* local obstacle avoidance algorithm},
  series = {CEAS Aeronautical Journal},
  journal   = {CEAS Aeronautical Journal},
  publisher = {Springer},
  address   = {Wien},
  issn      = {1869-5590 (Online)},
  doi       = {10.1007/s13272-023-00691-w},
  pages     = {11 Seiten},
  year      = {2023},
  abstract  = {Obstacle avoidance is critical for unmanned aerial vehicles (UAVs) operating autonomously. Obstacle avoidance algorithms either rely on global environment data or local sensor data. Local path planners react to unforeseen objects and plan purely on local sensor information. Similarly, animals need to find feasible paths based on local information about their surroundings. Therefore, their behavior is a valuable source of inspiration for path planning. Bumblebees tend to fly vertically over far-away obstacles and horizontally around close ones, implying two zones for different flight strategies depending on the distance to obstacles. This work enhances the local path planner 3DVFH* with this bio-inspired strategy. The algorithm alters the goal-driven function of the 3DVFH* to climb-preferring if obstacles are far away. Prior experiments with bumblebees led to two definitions of flight zone limits depending on the distance to obstacles, leading to two algorithm variants. Both variants reduce the probability of not reaching the goal of a 3DVFH* implementation in Matlab/Simulink. The best variant, 3DVFH*b-b, reduces this probability from 70.7 to 18.6\% in city-like worlds using a strong vertical evasion strategy. Energy consumption is higher, and flight paths are longer compared to the algorithm version with pronounced horizontal evasion tendency. A parameter study analyzes the effect of different weighting factors in the cost function. The best parameter combination shows a failure probability of 6.9\% in city-like worlds and reduces energy consumption by 28\%. Our findings demonstrate the potential of bio-inspired approaches for improving the performance of local path planning algorithms for UAV.},
  language  = {en}
}
@article{UlmerBraunChengetal.2023,
  author    = {Ulmer, Jessica and Braun, Carsten and Cheng, Chi-Tsun and Dowey, Steve and Wollert, J{\"o}rg},
  title     = {A human factors-aware assistance system in manufacturing based on gamification and hardware modularisation},
  series = {International Journal of Production Research},
  journal   = {International Journal of Production Research},
  publisher = {Taylor \& Francis},
  issn      = {0020-7543 (Print)},
  doi       = {10.1080/00207543.2023.2166140},
  year      = {2023},
  abstract  = {Assistance systems have been widely adopted in the manufacturing sector to facilitate various processes and tasks in production environments. However, existing systems are mostly equipped with rigid functional logic and do not provide individual user experiences or adapt to their capabilities. This work integrates human factors in assistance systems by adjusting the hardware and instruction presented to the workers' cognitive and physical demands. A modular system architecture is designed accordingly, which allows a flexible component exchange according to the user and the work task. Gamification, the use of game elements in non-gaming contexts, has been further adopted in this work to provide level-based instructions and personalised feedback. The developed framework is validated by applying it to a manual workstation for industrial assembly routines.},
  language  = {en}
}
@article{BoehnischBraunMuscarelloetal.2024,
  author    = {B{\"o}hnisch, Nils and Braun, Carsten and Muscarello, Vincenzo and Marzocca, Pier},
  title     = {About the wing and whirl flutter of a slender wing-propeller system},
  series = {Journal of Aircraft},
  journal   = {Journal of Aircraft},
  publisher = {American Institute of Aeronautics and Astronautics},
  issn      = {1533-3868},
  doi       = {10.2514/1.C037542},
  pages     = {1 -- 14},
  year      = {2024},
  abstract  = {Next-generation aircraft designs often incorporate multiple large propellers attached along the wingspan (distributed electric propulsion), leading to highly flexible dynamic systems that can exhibit aeroelastic instabilities. This paper introduces a validated methodology to investigate the aeroelastic instabilities of wing-propeller systems and to understand the dynamic mechanism leading to wing and whirl flutter and transition from one to the other. Factors such as nacelle positions along the wing span and chord and its propulsion system mounting stiffness are considered. Additionally, preliminary design guidelines are proposed for flutter-free wing-propeller systems applicable to novel aircraft designs. The study demonstrates how the critical speed of the wing-propeller systems is influenced by the mounting stiffness and propeller position. Weak mounting stiffnesses result in whirl flutter, while hard mounting stiffnesses lead to wing flutter. For the latter, the position of the propeller along the wing span may change the wing mode shapes and thus the flutter mechanism. Propeller positions closer to the wing tip enhance stability, but pusher configurations are more critical due to the mass distribution behind the elastic axis.},
  language  = {en}
}
@article{BoehnischBraunMuscarelloetal.2023,
  author    = {B{\"o}hnisch, Nils and Braun, Carsten and Muscarello, Vincenzo and Marzocca, Pier},
  title     = {A sensitivity study on aeroelastic instabilities of slender wings with a large propeller},
  series = {AIAA SCITECH 2023 Forum},
  journal   = {AIAA SCITECH 2023 Forum},
  publisher = {AIAA},
  doi       = {10.2514/6.2023-1893},
  pages     = {1 -- 14},
  year      = {2023},
  abstract  = {Next-generation aircraft designs often incorporate multiple large propellers attached along the wingspan. These highly flexible dynamic systems can exhibit uncommon aeroelastic instabilities, which should be carefully investigated to ensure safe operation. The interaction between the propeller and the wing is of particular importance. It is known that whirl flutter is stabilized by wing motion and wing aerodynamics. This paper investigates the effect of a propeller onto wing flutter as a function of span position and mounting stiffness between the propeller and wing. The analysis of a comparison between a tractor and pusher configuration has shown that the coupled system is more stable than the standalone wing for propeller positions near the wing tip for both configurations. The wing fluttermechanism is mostly affected by the mass of the propeller and the resulting change in eigenfrequencies of the wing. For very weak mounting stiffnesses, whirl flutter occurs, which was shown to be stabilized compared to a standalone propeller due to wing motion. On the other hand, the pusher configuration is, as to be expected, the more critical configuration due to the attached mass behind the elastic axis.},
  language  = {de}
}
@inproceedings{ThomaStiemerBraunetal.2023,
  author    = {Thoma, Andreas and Stiemer, Luc and Braun, Carsten and Fisher, Alex and Gardi, Alessandro G.},
  title     = {Potential of hybrid neural network local path planner for small UAV in urban environments},
  series = {AIAA SCITECH 2023 Forum},
  booktitle = {AIAA SCITECH 2023 Forum},
  publisher = {AIAA},
  doi       = {10.2514/6.2023-2359},
  pages     = {13 Seiten},
  year      = {2023},
  abstract  = {This work proposes a hybrid algorithm combining an Artificial Neural Network (ANN) with a conventional local path planner to navigate UAVs efficiently in various unknown urban environments. The proposed method of a Hybrid Artificial Neural Network Avoidance System is called HANNAS. The ANN analyses a video stream and classifies the current environment. This information about the current Environment is used to set several control parameters of a conventional local path planner, the 3DVFH*. The local path planner then plans the path toward a specific goal point based on distance data from a depth camera. We trained and tested a state-of-the-art image segmentation algorithm, PP-LiteSeg. The proposed HANNAS method reaches a failure probability of 17\%, which is less than half the failure probability of the baseline and around half the failure probability of an improved, bio-inspired version of the 3DVFH*. The proposed HANNAS method does not show any disadvantages regarding flight time or flight distance.},
  language  = {en}
}
@article{StiemerThomaBraun2023,
  author    = {Stiemer, Luc Nicolas and Thoma, Andreas and Braun, Carsten},
  title     = {MBT3D: Deep learning based multi-object tracker for bumblebee 3D flight path estimation},
  series = {PLoS ONE},
  volume    = {18},
  journal   = {PLoS ONE},
  number    = {9},
  publisher = {PLOS},
  address   = {San Fancisco},
  issn      = {1932-6203},
  doi       = {10.1371/journal.pone.0291415},
  pages     = {e0291415},
  year      = {2023},
  abstract  = {This work presents the Multi-Bees-Tracker (MBT3D) algorithm, a Python framework implementing a deep association tracker for Tracking-By-Detection, to address the challenging task of tracking flight paths of bumblebees in a social group. While tracking algorithms for bumblebees exist, they often come with intensive restrictions, such as the need for sufficient lighting, high contrast between the animal and background, absence of occlusion, significant user input, etc. Tracking flight paths of bumblebees in a social group is challenging. They suddenly adjust movements and change their appearance during different wing beat states while exhibiting significant similarities in their individual appearance. The MBT3D tracker, developed in this research, is an adaptation of an existing ant tracking algorithm for bumblebee tracking. It incorporates an offline trained appearance descriptor along with a Kalman Filter for appearance and motion matching. Different detector architectures for upstream detections (You Only Look Once (YOLOv5), Faster Region Proposal Convolutional Neural Network (Faster R-CNN), and RetinaNet) are investigated in a comparative study to optimize performance. The detection models were trained on a dataset containing 11359 labeled bumblebee images. YOLOv5 reaches an Average Precision of AP = 53, 8\%, Faster R-CNN achieves AP = 45, 3\% and RetinaNet AP = 38, 4\% on the bumblebee validation dataset, which consists of 1323 labeled bumblebee images. The tracker's appearance model is trained on 144 samples. The tracker (with Faster R-CNN detections) reaches a Multiple Object Tracking Accuracy MOTA = 93, 5\% and a Multiple Object Tracking Precision MOTP = 75, 6\% on a validation dataset containing 2000 images, competing with state-of-the-art computer vision methods. The framework allows reliable tracking of different bumblebees in the same video stream with rarely occurring identity switches (IDS). MBT3D has much lower IDS than other commonly used algorithms, with one of the lowest false positive rates, competing with state-of-the-art animal tracking algorithms. The developed framework reconstructs the 3-dimensional (3D) flight paths of the bumblebees by triangulation. It also handles and compares two alternative stereo camera pairs if desired.},
  language  = {en}
}