@article{MottaghyPechnigVogt2011,
  author    = {Mottaghy, Darius and Pechnig, Renate and Vogt, Christian},
  title     = {The geothermal project Den Haag: 3D numerical models for temperature prediction and reservoir simulation},
  series = {Geothermics},
  volume    = {40},
  journal   = {Geothermics},
  number    = {3},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0375-6505},
  doi       = {10.1016/j.geothermics.2011.07.001},
  pages     = {199 -- 210},
  year      = {2011},
  abstract  = {The proposed Den Haag Zuidwest district heating system of the city of The Hague consists of a deep doublet in a Jurassic sandstone layer that is designed for a production temperature of 75 °C and a reinjection temperature of 40 °C at a flow rate of 150 m3 h-1. The prediction of reservoir temperature and production behavior is crucial for success of the proposed geothermal doublet. This work presents the results of a study of the important geothermal and geohydrological issues for the doublet design. In the first phase of the study, the influences of the three-dimensional (3D) structures of anticlines and synclines on the temperature field were examined. A comprehensive petrophysical investigation was performed to build a large scale 3D-model of the reservoir. Several bottomhole temperatures (BHTs), as well as petrophysical logs were used to calibrate the model using thermal conductivity measurements on 50 samples from boreholes in different lithological units in the study area. Profiles and cross sections extracted from the calculated temperature field were used to study the temperature in the surrounding areas of the planned doublet. In the second phase of the project, a detailed 3D numerical reservoir model was set up, with the aim of predicting the evolution of the producer and injector temperatures, and the extent of the cooled area around the injector. The temperature model from the first phase provided the boundary conditions for the reservoir model. Hydraulic parameters for the target horizons, such as porosity and permeability, were taken from data available from the nearby exploration wells. The simulation results are encouraging as no significant thermal breakthrough is predicted. For the originally planned location of the producer, the extracted water temperature is predicted to be around 79 °C, with an almost negligible cooling in the first 50 years of production. When the producer is located shallower parts of the reservoir, the yield water temperatures is lower, starting at ≈76 °C and decreasing to ≈74 °C after 50 years of operation. This comparatively larger decrease in temperature with time is caused by the structural feature of the reservoir, namely a higher dip causes the cooler water to easily move downward. In view of the poor reservoir data, the reservoir simulation model is constructed to allow iterative updates using data assimilation during planned drilling, testing, and production phases. Measurements during an 8 h pumping test carried out in late 2010 suggest that a flow rate of 150 m3 h-1 is achievable. Fluid temperatures of 76.5 °C were measured, which is very close to the predicted value.},
  language  = {en}
}
@article{MottaghyDijkshoorn2012,
  author    = {Mottaghy, Darius and Dijkshoorn, Lydia},
  title     = {Implementing an effective finite difference formulation for borehole heat exchangers into a heat and mass transport code},
  series = {Renewable Energy},
  volume    = {45},
  journal   = {Renewable Energy},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0960-1481},
  doi       = {10.1016/j.renene.2012.02.013},
  pages     = {59 -- 71},
  year      = {2012},
  abstract  = {We present an effective finite difference formulation for implementing and modeling multiple borehole heat exchangers (BHE) in the general 3-D coupled heat and flow transport code SHEMAT. The BHE with arbitrary length can be either coaxial or double U-shaped. It is particularly suitable for modeling deep BHEs which contain varying pipe diameters and materials. Usually, in numerical simulations, a fine discretization of the BHE assemblage is required, due to the large geometric aspect ratios involved. This yields large models and long simulation times. The approach avoids this problem by considering heat transport between fluid and the soil through pipes and grout via thermal resistances. Therefore, the simulation time can be significantly reduced. The coupling with SHEMAT is realized by introducing an effective heat generation. Due to this connection, it is possible to consider heterogeneous geological models, as well as the influence of groundwater flow. This is particularly interesting when studying the long term behavior of a single BHE or a BHE field. Heating and cooling loads can enter the model with an arbitrary interval, e.g. from hourly to monthly values. When dealing with large BHE fields, computing times can be further significantly reduced by focusing on the temperature field around the BHEs, without explicitly modeling inlet and outlet temperatures. This allows to determine the possible migration of cold and warm plumes due to groundwater flow, which is of particular importance in urban areas with a high BHE installation density. The model is validated against the existing BHE modeling codes EWS and EED. A comparison with monitoring data from a deep BHE in Switzerland shows a good agreement. Synthetic examples demonstrate the field of application of this model.},
  language  = {en}
}
@article{VogtIwanowskiStrahserMarquartetal.2013,
  author    = {Vogt, Christian and Iwanowski-Strahser, Katha and Marquart, Gabriele and Arnold, Juliane and Mottaghy, Darius and Pechnig, Renate and Gnjezda, Daniel and Clauser, Christoph},
  title     = {Modeling contribution to risk assessment of thermal production power for geothermal reservoirs},
  series = {Renewable Energy},
  volume    = {53},
  journal   = {Renewable Energy},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0960-1481},
  doi       = {10.1016/j.renene.2012.11.026},
  pages     = {230 -- 241},
  year      = {2013},
  language  = {en}
}
@article{MiyamotoBingWagneretal.2015,
  author    = {Miyamoto, Ko-ichiro and Bing, Yu and Wagner, Torsten and Yoshinobu, Tatsuo and Sch{\"o}ning, Michael Josef},
  title     = {Visualization of Defects on a Cultured Cell Layer by Utilizing Chemical Imaging Sensor},
  series = {Procedia Engineering},
  volume    = {120},
  journal   = {Procedia Engineering},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1877-7058},
  doi       = {10.1016/j.proeng.2015.08.806},
  pages     = {936 -- 939},
  year      = {2015},
  abstract  = {The chemical imaging sensor is a field-effect sensor which is able to visualize both the distribution of ions (in LAPS mode) and the distribution of impedance (in SPIM mode) inthe sample. In this study, a novel wound-healing assay is proposed, in which the chemical imaging sensor operated in SPIM mode is applied to monitor the defect of a cell layer brought into proximity of the sensing surface.A reduced impedance inside the defect, which was artificially formed ina cell layer, was successfully visualized in a photocurrent image.},
  language  = {en}
}
@article{ChenClauserMarquartetal.2015,
  author    = {Chen, Tao and Clauser, Christoph and Marquart, Gabriele and Willbrand, Karen and Mottaghy, Darius},
  title     = {A new upscaling method for fractured porous media},
  series = {Advances in Water Resources},
  volume    = {80},
  journal   = {Advances in Water Resources},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0309-1708},
  doi       = {10.1016/j.advwatres.2015.03.009},
  pages     = {60 -- 68},
  year      = {2015},
  language  = {en}
}
@article{KuertenMottaghyZiegler2015,
  author    = {K{\"u}rten, Sylvia and Mottaghy, Darius and Ziegler, Martin},
  title     = {Design of plane energy geostructures based on laboratory tests and numerical modelling},
  series = {Energy and Buildings},
  volume    = {107},
  journal   = {Energy and Buildings},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0378-7788},
  doi       = {10.1016/j.enbuild.2015.08.039},
  pages     = {434 -- 444},
  year      = {2015},
  language  = {en}
}
@article{SchuellerKowalskiRaback2016,
  author    = {Sch{\"u}ller, K. and Kowalski, Julia and Raback, P.},
  title     = {Curvilinear melting - A preliminary experimental and numerical study},
  series = {International Journal of Heat and Mass Transfer},
  journal   = {International Journal of Heat and Mass Transfer},
  number    = {92},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0017-9310},
  doi       = {10.1016/j.ijheatmasstransfer.2015.09.046},
  pages     = {884 -- 892},
  year      = {2016},
  abstract  = {When exploring glacier ice it is often necessary to take samples or implement sensors at a certain depth underneath the glacier surface. One way of doing this is by using heated melting probes. In their common form these devices experience a straight one-dimensional downwards motion and can be modeled by standard close-contact melting theory. A recently developed melting probe however, the IceMole, achieves maneuverability by simultaneously applying a surface temperature gradient to induce a change in melting direction and controlling the effective contact-force by means of an ice screw to stabilize its change in attitude. A modeling framework for forced curvilinear melting does not exist so far and will be the content of this paper. At first, we will extend the existing theory for quasi-stationary close-contact melting to curved trajectories. We do this by introducing a rotational mode. This additional unknown in the system implies yet the need for another model closure. Within this new framework we will focus on the effect of a variable contact-force as well as different surface temperature profiles. In order to solve for melting velocity and curvature of the melting path we present both an inverse solution strategy for the analytical model, and a more general finite element framework implemented into the open source software package ELMER. Model results are discussed and compared to experimental data conducted in laboratory tests.},
  language  = {de}
}
@article{DiktaKuehlheimMendoncaetal.2015,
  author    = {Dikta, Gerhard and K{\"u}hlheim, Ren{\´e} and Mendonca, Jorge and Una-Alcarez, Jacobo de},
  title     = {Asymptotic representation of presmoothed Kaplan-Meier integrals with covariates in a semiparametric censorship model},
  series = {Journal of Statistical Planning and Inference},
  volume    = {Vol. 171},
  journal   = {Journal of Statistical Planning and Inference},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0378-3758},
  doi       = {10.1016/j.jspi.2015.12.001},
  pages     = {10 -- 37},
  year      = {2015},
  language  = {en}
}
@article{MarxSchenkBehrensetal.2013,
  author    = {Marx, Ulrich and Schenk, Friedrich and Behrens, Jan and Meyr, Ulrike and Wanek, Paul and Zang, Werner and Schmitt, Robert and Br{\"u}stle, Oliver and Zenke, Martin and Klocke, Fritz},
  title     = {Automatic production of induced pluripotent stem cells},
  series = {Procedia CIRP : First CIRP Conference on BioManufacturing},
  volume    = {Vol. 5},
  journal   = {Procedia CIRP : First CIRP Conference on BioManufacturing},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {2212-8271},
  pages     = {2 -- 6},
  year      = {2013},
  language  = {en}
}
@article{GuoMiyamotoWagneretal.2014,
  author    = {Guo, Yuanyuan and Miyamoto, Ko-ichiro and Wagner, Torsten and Sch{\"o}ning, Michael Josef and Yoshinobu, Tatsuo},
  title     = {Device simulation of the light-addressable potentiometric sensor for the investigation of the spatial resolution},
  series = {Sensors and actuators B: Chemical},
  volume    = {204},
  journal   = {Sensors and actuators B: Chemical},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1873-3077 (E-Journal); 0925-4005 (Print)},
  doi       = {10.1016/j.snb.2014.08.016},
  pages     = {659 -- 665},
  year      = {2014},
  abstract  = {As a semiconductor-based electrochemical sensor, the light-addressable potentiometric sensor (LAPS) can realize two dimensional visualization of (bio-)chemical reactions at the sensor surface addressed by localized illumination. Thanks to this imaging capability, various applications in biochemical and biomedical fields are expected, for which the spatial resolution is critically significant. In this study, therefore, the spatial resolution of the LAPS was investigated in detail based on the device simulation. By calculating the spatiotemporal change of the distributions of electrons and holes inside the semiconductor layer in response to a modulated illumination, the photocurrent response as well as the spatial resolution was obtained as a function of various parameters such as the thickness of the Si substrate, the doping concentration, the wavelength and the intensity of illumination. The simulation results verified that both thinning the semiconductor substrate and increasing the doping concentration could improve the spatial resolution, which were in good agreement with known experimental results and theoretical analysis. More importantly, new findings of interests were also obtained. As for the dependence on the wavelength of illumination, it was found that the known dependence was not always the case. When the Si substrate was thick, a longer wavelength resulted in a higher spatial resolution which was known by experiments. When the Si substrate was thin, however, a longer wavelength of light resulted in a lower spatial resolution. This finding was explained as an effect of raised concentration of carriers, which reduced the thickness of the space charge region. The device simulation was found to be helpful to understand the relationship between the spatial resolution and device parameters, to understand the physics behind it, and to optimize the device structure and measurement conditions for realizing higher performance of chemical imaging systems.},
  language  = {en}
}
@article{ReisertGeisslerWeileretal.2015,
  author    = {Reisert, Steffen and Geissler, H. and Weiler, C. and Wagner, P. and Sch{\"o}ning, Michael Josef},
  title     = {Multiple sensor-type system for monitoring the microbicidal effectiveness of aseptic sterilisation processes},
  series = {Food control},
  volume    = {47},
  journal   = {Food control},
  issn      = {1873-7129 (E-Journal); 0956-7135 (Print)},
  doi       = {10.1016/j.foodcont.2014.07.063},
  pages     = {615 -- 622},
  year      = {2015},
  abstract  = {The present work describes a novel multiple sensor-type system for the real-time analysis of aseptic sterilisation processes employing gaseous hydrogen peroxide (H2O2) as a sterilant. The inactivation kinetics of Bacillus atrophaeus by gaseous H2O2 have been investigated by means of a methodical calibration experiment, taking into account the process variables H2O2 concentration, humidity and gas temperature. It has been found that the microbicidal effectiveness at H2O2 concentrations above 2\% v/v is largely determined by the concentration itself, while at lower H2O2 concentrations, the gas temperature and humidity play a leading role. Furthermore, the responses of different types of gas sensors towards the influencing factors of the sterilisation process have been analysed within the same experiment. Based on a correlation established between the inactivation kinetics and the sensor responses, a calorimetric H2O2 sensor and a metal-oxide semiconductor (MOX) sensor have been identified as possible candidates for monitoring the microbicidal effectiveness of aseptic sterilisation processes employing gaseous H2O2. Therefore, two linear models that describe the relationship between sensor response and microbicidal effectiveness have been proposed.},
  language  = {en}
}
@article{MuellerHirschfeldLambertzetal.2014,
  author    = {M{\"u}ller, Martin and Hirschfeld, Julian and Lambertz, Rita and Schulze Lohoff, Andreas and Lustfeld, Hans and Pfeifer, Heinz and Reißel, Martin},
  title     = {Validation of a novel method for detecting and stabilizing malfunctioning areas in fuel cell stacks},
  series = {Journal of power sources},
  volume    = {272},
  journal   = {Journal of power sources},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1873-2755 (E-Journal); 0378-7753 (Print)},
  doi       = {10.1016/j.jpowsour.2014.08.045},
  pages     = {225 -- 232},
  year      = {2014},
  abstract  = {In this paper a setup for detecting malfunctioning areas of MEAs in fuel cell stacks is described. Malfunctioning areas generate electric cross currents inside bipolar plates. To exploit this we suggest bipolar plates consisting not of two but of three layers. The third one is a highly conducting layer and segmented such that the cross currents move along the segments to the surface of the stack where they can be measured by an inductive sensor. With this information a realistic model can be used to detect the malfunctioning area. Furthermore the third layer will prevent any current inhomogeneity of a malfunctioning cell to spread to neighbouring cells in the stack. In this work the results of measurements in a realistic cell setup will be compared with the results obtained in simulation studies with the same configuration. The basis for the comparison is the reliable characterisation of the electrical properties of the cell components and the implication of these results into the simulation model. The experimental studies will also show the limits in the maximum number of segments, which can be used for a reliable detection of cross currents.},
  language  = {en}
}
@article{StadlerGarveyEmbsetal.2014,
  author    = {Stadler, Alexander Maximilian and Garvey, Christopher J. and Embs, Jan Peter and Koza, Michael Marek and Unruh, Tobias and Artmann, Gerhard and Zaccai, Guiseppe},
  title     = {Picosecond dynamics in haemoglobin from different species: A quasielastic neutron scattering study},
  series = {Biochimica et biophysica acta (BBA): General Subjects},
  volume    = {1840},
  journal   = {Biochimica et biophysica acta (BBA): General Subjects},
  number    = {10},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1872-8006 (E-Journal); 0304-4165 (Print)},
  doi       = {10.1016/j.bbagen.2014.06.007},
  pages     = {2989 -- 2999},
  year      = {2014},
  language  = {en}
}
@article{YoshinobuMiyamotoWagneretal.2015,
  author    = {Yoshinobu, Tatsuo and Miyamoto, Ko-ichiro and Wagner, Torsten and Sch{\"o}ning, Michael Josef},
  title     = {Recent developments of chemical imaging sensor systems based on the principle of the light-addressable potentiometric sensor},
  series = {Sensors and actuators B: Chemical},
  volume    = {207, Part B},
  journal   = {Sensors and actuators B: Chemical},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1873-3077 (E-Journal); 0925-4005 (Print)},
  doi       = {10.1016/j.snb.2014.09.002},
  pages     = {926 -- 932},
  year      = {2015},
  abstract  = {The light-addressable potentiometric sensor (LAPS) is an electrochemical sensor with a field-effect structure to detect the variation of the Nernst potential at its sensor surface, the measured area on which is defined by illumination. Thanks to this light-addressability, the LAPS can be applied to chemical imaging sensor systems, which can visualize the two-dimensional distribution of a particular target ion on the sensor surface. Chemical imaging sensor systems are expected to be useful for analysis of reaction and diffusion in various electrochemical and biological samples. Recent developments of LAPS-based chemical imaging sensor systems, in terms of the spatial resolution, measurement speed, image quality, miniaturization and integration with microfluidic devices, are summarized and discussed.},
  language  = {en}
}
@article{MuribYeapMartensetal.2015,
  author    = {Murib, M. S. and Yeap, W. S. and Martens, D. and Liu, X. and Bienstman, P. and Fahlman, M. and Sch{\"o}ning, Michael Josef and Michiels, L. and Haenen, K. and Serpeng{\"u}zel, A. and Wagner, Patrick},
  title     = {Photonic studies on polymer-coated sapphire-spheres : a model system for biological ligands},
  series = {Sensors and actuators A: Physical},
  volume    = {222},
  journal   = {Sensors and actuators A: Physical},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1873-3069 (E-Journal); 0924-4247 (Print)},
  doi       = {10.1016/j.sna.2014.11.024},
  pages     = {212 -- 219},
  year      = {2015},
  abstract  = {In this study we show an optical biosensor concept, based on elastic light scattering from sapphire microspheres. Transmitted and elastic scattering intensity of the microspheres (radius 500 μm, refractive index 1.77) on an optical fiber half coupler is analyzed at 1510 nm. The 0.43 nm angular mode spacing of the resonances is comparable to the angular mode spacing value estimated using the optical size of the microsphere. The spectral linewidths of the resonances are in the order of 0.01 nm, which corresponds to quality factors of approximately 105. A polydopamine layer is used as a functionalizing agent on sapphire microspherical resonators in view of biosensor implementation. The varying layer thickness on the microsphere is determined as a function of the resonance wavelength shift. It is shown that polymer functionalization has a minor effect on the quality factor. This is a promising step toward the development of an optical biosensor.},
  language  = {en}
}
@article{GuoSekiMiyamotoetal.2014,
  author    = {Guo, Yuanyuan and Seki, Kosuke and Miyamoto, Ko-ichiro and Wagner, Torsten and Sch{\"o}ning, Michael Josef and Yoshinobu, Tatsuo},
  title     = {Device simulation of the light-addressable potentiometric sensor with a novel photoexcitation method for a higher spatial resolution},
  series = {Procedia Engineering},
  volume    = {87},
  journal   = {Procedia Engineering},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1877-7058},
  doi       = {10.1016/j.proeng.2014.11.369},
  pages     = {456 -- 459},
  year      = {2014},
  abstract  = {A novel photoexcitation method for the light-addressable potentiometric sensor (LAPS) realized a higher spatial resolution of chemical imaging. In this method, a modulated light probe, which generates the alternating photocurrent signal, is surrounded by a ring of constant light, which suppresses the lateral diffusion of photocarriers by enhancing recombination. A device simulation verified that a higher spatial resolution could be obtained by adjusting the gap between the modulated and constant light. It was also found that a higher intensity and a longer wavelength of constant light was more effective. However, there exists a tradeoff between the spatial resolution and the amplitude of the photocurrent, and thus, the signal-to-noise ratio. A tilted incidence of constant light was applied, which could achieve even higher resolution with a smaller loss of photocurrent.},
  language  = {en}
}
@article{MiyamotoSekiWagneretal.2014,
  author    = {Miyamoto, K. and Seki, K. and Wagner, Torsten and Sch{\"o}ning, Michael Josef and Yoshinobu, T.},
  title     = {Enhancement of the spatial resolution of the chemical imaging sensor by a hybrid fiber-optic illumination},
  series = {Procedia Engineering},
  volume    = {87},
  journal   = {Procedia Engineering},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1877-7058},
  doi       = {10.1016/j.proeng.2014.11.563},
  pages     = {612 -- 615},
  year      = {2014},
  abstract  = {The chemical imaging sensor, which is based on the principle of the light-addressable potentiometric sensor (LAPS), is a powerful tool to visualize the spatial distribution of chemical species on the sensor surface. The spatial resolution of this sensor depends on the diffusion of photocarriers excited by a modulated light. In this study, a novel hybrid fiber-optic illumination was developed to enhance the spatial resolution. It consists of a modulated light probe to generate a photocurrent signal and a ring of constant light, which suppresses the lateral diffusion of minority carriers excited by the modulated light. It is demonstrated that the spatial resolution was improved from 92 μm to 68 μm.},
  language  = {en}
}
@incollection{SeiblerSchwenk2010,
  author    = {Seibler, Jost and Schwenk, Frieder},
  title     = {Transgenic RNAi Applications in the Mouse},
  series = {Methods in Enzymology : Guide to Techniques in Mouse Development, Part B: Mouse Molecular Genetics. 2nd Edition},
  booktitle = {Methods in Enzymology : Guide to Techniques in Mouse Development, Part B: Mouse Molecular Genetics. 2nd Edition},
  publisher = {Elsevier},
  address   = {Amsterdam},
  isbn      = {978-0-12-384880-2},
  pages     = {367 -- 386},
  year      = {2010},
  language  = {en}
}
@article{HenkenOosterhuisOehlschlaegeretal.2012,
  author    = {Henken, F. E. and Oosterhuis, K. and {\"O}hlschl{\"a}ger, Peter and Bosch, L. and Hooijberg, E. and Haanen, J. B. A. G. and Steenbergen, R. D. M.},
  title     = {Preclinical safety evaluation of DNA vaccines encoding modified HPV16 E6 and E7},
  series = {Vaccine},
  volume    = {30},
  journal   = {Vaccine},
  number    = {28},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0264-410X},
  doi       = {10.1016/j.vaccine.2012.04.013},
  pages     = {4259 -- 4266},
  year      = {2012},
  abstract  = {Persistent infection with high-risk human papillomaviruses (hrHPV) can result in the formation of anogenital cancers. As hrHPV proteins E6 and E7 are required for cancer initiation and maintenance, they are ideal targets for immunotherapeutic interventions. Previously, we have described the development of DNA vaccines for the induction of HPV16 E6 and E7 specific T cell immunity. These vaccines consist of 'gene-shuffled' (SH) versions of HPV16 E6 and E7 that were fused to Tetanus Toxin Fragment C domain 1 (TTFC) and were named TTFC-E6SH and TTFC-E7SH. Gene-shuffling was performed to avoid the risk of inducing malignant transformation at the vaccination site. Here, we describe the preclinical safety evaluation of these candidate vaccines by analysis of their transforming capacity in vitro using established murine fibroblasts (NIH 3T3 cells) and primary human foreskin keratinocytes (HFKs). We demonstrate that neither ectopic expression of TTFC-E6SH and TTFC-E7SH alone or in combination enabled NIH 3T3 cells to form colonies in soft agar. In contrast, expression of HPV16 E6WT and E7WT alone or in combination resulted in effective transformation. Similarly, retroviral transduction of HFKs from three independent donors with both TTFC-E6SH and TTFC-E7SH alone or in combination did not show any signs of immortalization. In contrast, the combined expression of E6WT and E7WT induced immortalization in HFKs from all donors. Based on these results we consider it justified to proceed to clinical evaluation of DNA vaccines encoding TTFC-E6SH and TTFC-E7SH in patients with HPV16 associated (pre)malignancies.},
  language  = {en}
}
@article{FellinKingKirschetal.2010,
  author    = {Fellin, Wolfgang and King, Julian and Kirsch, Ansgar and Oberguggenberger, Michael},
  title     = {Uncertainty modelling and sensitivity analysis of tunnel face stability},
  series = {Structural safety},
  volume    = {32},
  journal   = {Structural safety},
  number    = {6},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0167-4730},
  doi       = {10.1016/j.strusafe.2010.06.001},
  pages     = {402 -- 410},
  year      = {2010},
  abstract  = {This paper proposes an approach to the choice and evaluation of engineering models with the aid of a typical application in geotechnics. An important issue in the construction of shallow tunnels, especially in weak ground conditions, is the tunnel face stability. Various theoretical and numerical models for predicting the necessary support pressure have been put forth in the literature. In this paper, we combine laboratory experiments performed at the University of Innsbruck with current methods of uncertainty and sensitivity analysis for assessing adequacy, predictive power and robustness of the models. The major issues are the handling of the twofold uncertainty of test results and of model predictions as well as the decision about what are the influential input parameters.},
  language  = {en}
}
@article{ScheerSnaithWolfetal.2013,
  author    = {Scheer, Nico and Snaith, Mike and Wolf, C. Roland and Seibler, Jost},
  title     = {Generation and utility of genetically humanized mouse models},
  series = {Drug Discovery Today},
  volume    = {Vol 18},
  journal   = {Drug Discovery Today},
  number    = {23-24},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1359-6446},
  doi       = {10.1016/j.drudis.2013.07.007},
  pages     = {1200 -- 1211},
  year      = {2013},
  language  = {en}
}
@article{OberlaenderKirchnerKeusgenetal.2015,
  author    = {Oberl{\"a}nder, Jan and Kirchner, Patrick and Keusgen, Michael and Sch{\"o}ning, Michael Josef},
  title     = {Strategies in developing thin-film sensors for monitoring aseptic food processes : Theoretical considerations and investigations of passivation materials},
  series = {Electrochimica Acta},
  volume    = {183},
  journal   = {Electrochimica Acta},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0013-4686},
  doi       = {10.1016/j.electacta.2015.06.126},
  pages     = {130 -- 136},
  year      = {2015},
  abstract  = {The sterilization of packages in aseptic food processes is highly significant to maintain a consumer-safe product with extended shelf-life. Today, the sterilization of food packages is predominantly accomplished by gaseous hydrogen peroxide (H2O2) in combination with heat. In order to monitor this sterilization process, calorimetric gas sensors as differential set-up of two platinum temperature sensors representing a catalytically active (additionally deposition of MnO2) and a passive segment have been recently developed. The temperature rise of the exothermic decomposition serves as an indicator of the present H2O2 concentration. In the present work, a theoretical approach considering the sensor's thermochemistry and physical transport phenomena was formulated to evaluate the temperature rise based on the energy content of gaseous H2O2. In a further part of this work, three polymers have been analyzed with respect to their application as passivation materials. The examined polymers are photoresist SU-8, perfluoroalkoxy (PFA) and fluorinated ethylene propylene (FEP). Thermal analyses by means of differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) have been conducted to determine the operation limits of the polymers. The overall chemical resistance and stability of the polymers against the harsh environmental conditions during the sterilization process have been examined by attenuated total reflection Fourier transform infrared spectroscopy (ATR-FTIR).},
  language  = {en}
}
@article{MiyamatoSakakitaWagneretal.2015,
  author    = {Miyamato, Ko-ichiro and Sakakita, Sakura and Wagner, Torsten and Sch{\"o}ning, Michael Josef and Yoshinobu, Tatsuo},
  title     = {Application of chemical imaging sensor to in-situ pH imaging in the vicinity of a corroding metal surface},
  series = {Electrochimica Acta},
  volume    = {183},
  journal   = {Electrochimica Acta},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0013-4686},
  doi       = {10.1016/j.electacta.2015.07.184},
  pages     = {137 -- 142},
  year      = {2015},
  abstract  = {The chemical imaging sensor was applied to in-situ pH imaging of the solution in the vicinity of a corroding surface of stainless steel under potentiostatic polarization. A test piece of polished stainless steel was placed on the sensing surface leaving a narrow gap filled with artificial seawater and the stainless steel was corroded under polarization. The pH images obtained during polarization showed correspondence between the region of lower pH and the site of corrosion. It was also found that the pH value in the gap became as low as 2 by polarization, which triggered corrosion.},
  language  = {en}
}
@article{BayonValeroGarciaBartualetal.2016,
  author    = {Bayon, Arnau and Valero, Daniel and Garcia-Bartual, Rafael and Vall{\´e}s-Mor{\´a}n, Francisco Jos{\´e} and L{\´o}pez-Jim{\´e}nez, P. Amparo},
  title     = {Performance assessment of OpenFOAM and FLOW-3D in the numerical modeling of a low Reynolds number hydraulic jump},
  series = {Environmental Modelling \& Software},
  volume    = {80},
  journal   = {Environmental Modelling \& Software},
  publisher = {Elsevier},
  address   = {Amsterdam},
  isbn      = {1364-8152},
  doi       = {10.1016/j.envsoft.2016.02.018},
  pages     = {322 -- 335},
  year      = {2016},
  abstract  = {A comparative performance analysis of the CFD platforms OpenFOAM and FLOW-3D is presented, focusing on a 3D swirling turbulent flow: a steady hydraulic jump at low Reynolds number. Turbulence is treated using RANS approach RNG k-ε. A Volume Of Fluid (VOF) method is used to track the air-water interface, consequently aeration is modeled using an Eulerian-Eulerian approach. Structured meshes of cubic elements are used to discretize the channel geometry. The numerical model accuracy is assessed comparing representative hydraulic jump variables (sequent depth ratio, roller length, mean velocity profiles, velocity decay or free surface profile) to experimental data. The model results are also compared to previous studies to broaden the result validation. Both codes reproduced the phenomenon under study concurring with experimental data, although special care must be taken when swirling flows occur. Both models can be used to reproduce the hydraulic performance of energy dissipation structures at low Reynolds numbers.},
  language  = {en}
}
@article{MiyamotoYuIsodaetal.2016,
  author    = {Miyamoto, Ko-ichiro and Yu, Bing and Isoda, Hiroko and Wagner, Torsten and Sch{\"o}ning, Michael Josef and Yoshinobu, Tatsuo},
  title     = {Visualization of the recovery process of defects in a cultured cell layer by chemical imaging sensor},
  series = {Sensors and Actuators B: Chemical},
  volume    = {236},
  journal   = {Sensors and Actuators B: Chemical},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0925-4005},
  doi       = {10.1016/j.snb.2016.04.018},
  pages     = {965 -- 969},
  year      = {2016},
  abstract  = {The chemical imaging sensor is a field-effect sensor which is able to visualize both the distribution of ions (in LAPS mode) and the distribution of impedance (in SPIM mode) in the sample. In this study, a novel cell assay is proposed, in which the chemical imaging sensor operated in SPIM mode is applied to monitor the recovery of defects in a cell layer brought into proximity of the sensing surface. A reduced impedance at a defect formed artificially in a cell layer was successfully visualized in a photocurrent image. The cell layer was cultured over two weeks, during which the temporal change of the photocurrent distribution corresponding to the recovery of the defect was observed.},
  language  = {de}
}
@article{EdipSesovButenwegetal.2018,
  author    = {Edip, K. and Sesov, V. and Butenweg, Christoph and Bojadjieva, J.},
  title     = {Development of coupled numerical model for simulation of multiphase soil},
  series = {Computers and Geotechnics},
  volume    = {96},
  journal   = {Computers and Geotechnics},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0266-352X},
  doi       = {10.1016/j.compgeo.2017.08.016},
  pages     = {118 -- 131},
  year      = {2018},
  abstract  = {In this paper, a coupled multiphase model considering both non-linearities of water retention curves and solid state modeling is proposed. The solid displacements and the pressures of both water and air phases are unknowns of the proposed model. The finite element method is used to solve the governing differential equations. The proposed method is demonstrated through simulation of seepage test and partially consolidation problem. Then, implementation of the model is done by using hypoplasticity for the solid phase and analyzing the fully saturated triaxial experiments. In integration of the constitutive law error controlling is improved and comparisons done accordingly. In this work, the advantages and limitations of the numerical model are discussed.},
  language  = {en}
}
@article{ZhangValeroBungetal.2018,
  author    = {Zhang, G. and Valero, Daniel and Bung, Daniel Bernhard and Chanson, H.},
  title     = {On the estimation of free-surface turbulence using ultrasonic sensors},
  series = {Flow Measurement and Instrumentation},
  volume    = {60},
  journal   = {Flow Measurement and Instrumentation},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0955-5986},
  doi       = {10.1016/j.flowmeasinst.2018.02.009},
  pages     = {171 -- 184},
  year      = {2018},
  abstract  = {Accurate determination of free-surface dynamics has attracted much research attention during the past decade and has important applications in many environmental and water related areas. In this study, the free-surface dynamics in several turbulent flows commonly found in nature were investigated using a synchronised setup consisting of an ultrasonic sensor and a high-speed video camera. Basic sensor capabilities were examined in dry conditions to allow for a better characterisation of the present sensor model. The ultrasonic sensor was found to adequately reproduce free-surface dynamics up to the second order, especially in two-dimensional scenarios with the most energetic modes in the low frequency range. The sensor frequency response was satisfactory in the sub-20 Hz band, and its signal quality may be further improved by low-pass filtering prior to digitisation. The application of the USS to characterise entrapped air in high-velocity flows is also discussed.},
  language  = {en}
}
@article{MarinkovicButenweg2022,
  author    = {Marinkovic, Marko and Butenweg, Christoph},
  title     = {Numerical analysis of the in-plane behaviour of decoupled masonry infilled RC frames},
  series = {Engineering Structures},
  volume    = {272},
  journal   = {Engineering Structures},
  number    = {1},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0141-0296},
  doi       = {10.1016/j.engstruct.2022.114959},
  pages     = {18 Seiten},
  year      = {2022},
  abstract  = {Damage of reinforced concrete (RC) frames with masonry infill walls has been observed after many earthquakes. Brittle behaviour of the masonry infills in combination with the ductile behaviour of the RC frames makes infill walls prone to damage during earthquakes. Interstory deformations lead to an interaction between the infill and the RC frame, which affects the structural response. The result of this interaction is significant damage to the infill wall and sometimes to the surrounding structural system too. In most design codes, infill walls are considered as non-structural elements and neglected in the design process, because taking into account the infills and considering the interaction between frame and infill in software packages can be complicated and impractical. A good way to avoid negative aspects arising from this behavior is to ensure no or low-interaction of the frame and infill wall, for instance by decoupling the infill from the frame. This paper presents the numerical study performed to investigate new connection system called INODIS (Innovative Decoupled Infill System) for decoupling infill walls from surrounding frame with the aim to postpone infill activation to high interstory drifts thus reducing infill/frame interaction and minimizing damage to both infills and frames. The experimental results are first used for calibration and validation of the numerical model, which is then employed for investigating the influence of the material parameters as well as infill's and frame's geometry on the in-plane behaviour of the infilled frames with the INODIS system. For all the investigated situations, simulation results show significant improvements in behaviour for decoupled infilled RC frames in comparison to the traditionally infilled frames.},
  language  = {en}
}
@article{PeloniDachwaldCeriotti2017,
  author    = {Peloni, Alessandro and Dachwald, Bernd and Ceriotti, Matteo},
  title     = {Multiple near-earth asteroid rendezvous mission: Solar-sailing options},
  series = {Advances in Space Research},
  journal   = {Advances in Space Research},
  number    = {In Press, Corrected Proof},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0273-1177},
  doi       = {10.1016/j.asr.2017.10.017},
  year      = {2017},
  language  = {en}
}
@article{KezerashviliDachwald2021,
  author    = {Kezerashvili, Roman Ya and Dachwald, Bernd},
  title     = {Preface: Solar sailing: Concepts, technology, and missions II},
  series = {Advances in Space Research},
  volume    = {67},
  journal   = {Advances in Space Research},
  number    = {9},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0273-1177},
  doi       = {10.1016/j.asr.2021.01.037},
  pages     = {2559 -- 2560},
  year      = {2021},
  language  = {en}
}
@article{SpietzSproewitzSeefeldtetal.2021,
  author    = {Spietz, Peter and Spr{\"o}witz, Tom and Seefeldt, Patric and Grundmann, Jan Thimo and Jahnke, Rico and Mikschl, Tobias and Mikulz, Eugen and Montenegro, Sergio and Reershemius, Siebo and Renger, Thomas and Ruffer, Michael and Sasaki, Kaname and Sznajder, Maciej and T{\´o}th, Norbert and Ceriotti, Matteo and Dachwald, Bernd and Macdonald, Malcolm and McInnes, Colin and Seboldt, Wolfgang and Quantius, Dominik and Bauer, Waldemar and Wiedemann, Carsten and Grimm, Christian D. and Hercik, David and Ho, Tra-Mi and Lange, Caroline and Schmitz, Nicole},
  title     = {Paths not taken - The Gossamer roadmap's other options},
  series = {Advances in Space Research},
  volume    = {67},
  journal   = {Advances in Space Research},
  number    = {9},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0273-1177},
  doi       = {10.1016/j.asr.2021.01.044},
  pages     = {2912 -- 2956},
  year      = {2021},
  language  = {en}
}
@article{ValeroBung2016,
  author    = {Valero, Daniel and Bung, Daniel Bernhard},
  title     = {Development of the interfacial air layer in the non-aerated region of high-velocity spillway flows: Instabilities growth, entrapped air and influence on the self-aeration onset},
  series = {International Journal of Multiphase Flow},
  volume    = {84},
  journal   = {International Journal of Multiphase Flow},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0301-9322},
  doi       = {10.1016/j.ijmultiphaseflow.2016.04.012},
  pages     = {66 -- 74},
  year      = {2016},
  abstract  = {Self-aeration is traditionally explained by the water turbulent boundary layer outer edge intersection with the free surface. This paper presents a discussion on the commonly accepted hypothesis behind the computation of the critical point of self-aeration in spillway flows and a new formulation is proposed based on the existence of a developing air flow over the free surface. Upstream of the inception point of self-aeration, some surface roughening has been often reported in previous studies which consequently implies some entrapped air transport and air-water flows coupling. Such air flow is proven in this study by presenting measured air velocities and computing the air boundary layer thickness for a 1V:2H smooth chute flow. Additionally, the growth rate of free surface waves has been analysed by means of Ultrasonic Sensors measurements, obtaining also the entrapped air concentration. High-speed camera imaging has been used for qualitative study of the flow perturbations.},
  language  = {en}
}
@article{NeuJanserKhatibietal.2016,
  author    = {Neu, Eugen and Janser, Frank and Khatibi, Akbar A. and Braun, Carsten and Orifici, Adrian C.},
  title     = {Operational Modal Analysis of a wing excited by transonic flow},
  series = {Aerospace Science and Technology},
  volume    = {49},
  journal   = {Aerospace Science and Technology},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1270-9638},
  doi       = {10.1016/j.ast.2015.11.032},
  pages     = {73 -- 79},
  year      = {2016},
  abstract  = {Operational Modal Analysis (OMA) is a promising candidate for flutter testing and Structural Health Monitoring (SHM) of aircraft wings that are passively excited by wind loads. However, no studies have been published where OMA is tested in transonic flows, which is the dominant condition for large civil aircraft and is characterized by complex and unique aerodynamic phenomena. We use data from the HIRENASD large-scale wind tunnel experiment to automatically extract modal parameters from an ambiently excited wing operated in the transonic regime using two OMA methods: Stochastic Subspace Identification (SSI) and Frequency Domain Decomposition (FDD). The system response is evaluated based on accelerometer measurements. The excitation is investigated from surface pressure measurements. The forcing function is shown to be non-white, non-stationary and contaminated by narrow-banded transonic disturbances. All these properties violate fundamental OMA assumptions about the forcing function. Despite this, all physical modes in the investigated frequency range were successfully identified, and in addition transonic pressure waves were identified as physical modes as well. The SSI method showed superior identification capabilities for the investigated case. The investigation shows that complex transonic flows can interfere with OMA. This can make existing approaches for modal tracking unsuitable for their application to aircraft wings operated in the transonic flight regime. Approaches to separate the true physical modes from the transonic disturbances are discussed.},
  language  = {en}
}
@article{NgamgaBialonskiMarwanetal.2016,
  author    = {Ngamga, Eulalie Joelle and Bialonski, Stephan and Marwan, Norbert and Kurths, J{\"u}rgen and Geier, Christian and Lehnertz, Klaus},
  title     = {Evaluation of selected recurrence measures in discriminating pre-ictal and inter-ictal periods from epileptic EEG data},
  series = {Physics Letters A},
  volume    = {380},
  journal   = {Physics Letters A},
  number    = {16},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0375-9601},
  doi       = {10.1016/j.physleta.2016.02.024},
  pages     = {1419 -- 1425},
  year      = {2016},
  abstract  = {We investigate the suitability of selected measures of complexity based on recurrence quantification analysis and recurrence networks for an identification of pre-seizure states in multi-day, multi-channel, invasive electroencephalographic recordings from five epilepsy patients. We employ several statistical techniques to avoid spurious findings due to various influencing factors and due to multiple comparisons and observe precursory structures in three patients. Our findings indicate a high congruence among measures in identifying seizure precursors and emphasize the current notion of seizure generation in large-scale epileptic networks. A final judgment of the suitability for field studies, however, requires evaluation on a larger database.},
  language  = {en}
}
@article{RachingerBauchStrittmatteretal.2013,
  author    = {Rachinger, Michael and Bauch, Melanie and Strittmatter, Axel and Bongaerts, Johannes and Evers, Stefan and Maurer, Karl-Heinz and Daniel, Rolf and Liebl, Wolfgang and Liesegang, Heiko and Ehrenreich, Armin},
  title     = {Size unlimited markerless deletions by a transconjugative plasmid-system in Bacillus licheniformis},
  series = {Journal of biotechnology},
  volume    = {Vol. 164},
  journal   = {Journal of biotechnology},
  number    = {Iss. 4},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1873-4863 (E-Journal); 0168-1656 (Print)},
  pages     = {365 -- 369},
  year      = {2013},
  language  = {en}
}
@article{WoliszSchuetzBlankeetal.2017,
  author    = {Wolisz, Henryk and Sch{\"u}tz, Thomas and Blanke, Tobias and Hagenkamp, Markus and Kohrn, Markus and Wesseling, Mark and M{\"u}ller, Dirk},
  title     = {Cost optimal sizing of smart buildings' energy system components considering changing end-consumer electricity markets},
  series = {Energy},
  volume    = {137},
  journal   = {Energy},
  publisher = {Elsevier},
  address   = {Amsterdam},
  doi       = {10.1016/j.energy.2017.06.025},
  pages     = {715 -- 728},
  year      = {2017},
  language  = {en}
}
@article{LehnertzAnsmannBialonskietal.2014,
  author    = {Lehnertz, Klaus and Ansmann, Gerrit and Bialonski, Stephan and Dickten, Henning and Geier, Christian and Porz, Stephan},
  title     = {Evolving networks in the human epileptic brain},
  series = {Physica D: Nonlinear Phenomena},
  volume    = {267},
  journal   = {Physica D: Nonlinear Phenomena},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0167-2789},
  doi       = {10.1016/j.physd.2013.06.009},
  pages     = {7 -- 15},
  year      = {2014},
  abstract  = {Network theory provides novel concepts that promise an improved characterization of interacting dynamical systems. Within this framework, evolving networks can be considered as being composed of nodes, representing systems, and of time-varying edges, representing interactions between these systems. This approach is highly attractive to further our understanding of the physiological and pathophysiological dynamics in human brain networks. Indeed, there is growing evidence that the epileptic process can be regarded as a large-scale network phenomenon. We here review methodologies for inferring networks from empirical time series and for a characterization of these evolving networks. We summarize recent findings derived from studies that investigate human epileptic brain networks evolving on timescales ranging from few seconds to weeks. We point to possible pitfalls and open issues, and discuss future perspectives.},
  language  = {en}
}
@article{GrundmannDachwaldGrimmetal.2015,
  author    = {Grundmann, Jan Thimo and Dachwald, Bernd and Grimm, Christian D. and Kahle, Ralph and Koch, Aaron Dexter and Krause, Christian and Lange, Caroline and Quantius, Dominik and Ulamec, Stephan},
  title     = {Spacecraft for Hypervelocity Impact Research - An Overview of Capabilities, Constraints and the Challenges of Getting There},
  series = {Procedia Engineering},
  volume    = {Vol. 103},
  journal   = {Procedia Engineering},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1877-7058},
  doi       = {10.1016/j.proeng.2015.04.021},
  pages     = {151 -- 158},
  year      = {2015},
  language  = {en}
}
@article{RuebbelkeVoegeleGrajewskietal.2023,
  author    = {R{\"u}bbelke, Dirk and V{\"o}gele, Stefan and Grajewski, Matthias and Zobel, Luzy},
  title     = {Cross border adjustment mechanism: Initial data for the assessment of hydrogen-based steel production},
  series = {Data in Brief},
  volume    = {47},
  journal   = {Data in Brief},
  number    = {Article 108907},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {2352-3409},
  doi       = {10.1016/j.dib.2023.108907},
  pages     = {1 -- 5},
  year      = {2023},
  abstract  = {Ambitious climate targets affect the competitiveness of industries in the international market. To prevent such industries from moving to other countries in the wake of increased climate protection efforts, cost adjustments may become necessary. Their design requires knowledge of country-specific production costs. Here, we present country-specific cost figures for different production routes of steel, paying particular attention to transportation costs. The data can be used in floor price models aiming to assess the competitiveness of different steel production routes in different countries (R{\"u}bbelke, 2022).},
  language  = {en}
}
@article{JungMuellerStaat2018,
  author    = {Jung, Alexander and M{\"u}ller, Wolfram and Staat, Manfred},
  title     = {Wind and fairness in ski jumping: A computer modelling analysis},
  series = {Journal of Biomechanics},
  journal   = {Journal of Biomechanics},
  number    = {75},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0021-9290},
  doi       = {10.1016/j.jbiomech.2018.05.001},
  pages     = {147 -- 153},
  year      = {2018},
  abstract  = {Wind is closely associated with the discussion of fairness in ski jumping. To counter-act its influence on the jump length, the International Ski Federation (FIS) has introduced a wind compensation approach. We applied three differently accurate computer models of the flight phase with wind (M1, M2, and M3) to study the jump length effects of various wind scenarios. The previously used model M1 is accurate for wind blowing in direction of the flight path, but inaccuracies are to be expected for wind directions deviating from the tangent to the flight path. M2 considers the change of airflow direction, but it does not consider the associated change in the angle of attack of the skis which additionally modifies drag and lift area time functions. M3 predicts the length effect for all wind directions within the plane of the flight trajectory without any mathematical simplification. Prediction errors of M3 are determined only by the quality of the input data: wind velocity, drag and lift area functions, take-off velocity, and weight. For comparing the three models, drag and lift area functions of an optimized reference jump were used. Results obtained with M2, which is much easier to handle than M3, did not deviate noticeably when compared to predictions of the reference model M3. Therefore, we suggest to use M2 in future applications. A comparison of M2 predictions with the FIS wind compensation system showed substantial discrepancies, for instance: in the first flight phase, tailwind can increase jump length, and headwind can decrease it; this is opposite of what had been anticipated before and is not considered in the current wind compensation system in ski jumping.},
  language  = {en}
}
@article{JungStaatMueller2018,
  author    = {Jung, Alexander and Staat, Manfred and M{\"u}ller, Wolfram},
  title     = {Corrigendum to "Flight style optimization in ski jumping on normal, large, and ski flying hills" [J. Biomech 47 (2014) 716-722]},
  series = {Journals of Biomechanics},
  journal   = {Journals of Biomechanics},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0021-9290},
  doi       = {10.1016/j.jbiomech.2018.02.001},
  pages     = {313},
  year      = {2018},
  language  = {en}
}
@article{FateriGebhardtThuemmleretal.2014,
  author    = {Fateri, Miranda and Gebhardt, Andreas and Th{\"u}mmler, Stefan and Thurn, Laura},
  title     = {Experimental investigation on selective laser melting of glass},
  series = {Physics procedia : 8th International Conference on Laser Assisted Net Shape Engineering LANE 2014},
  volume    = {56 (2014)},
  journal   = {Physics procedia : 8th International Conference on Laser Assisted Net Shape Engineering LANE 2014},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1875-3892 (E-Journal); 1875-3884 (Print)},
  doi       = {10.1016/j.phpro.2014.08.118},
  pages     = {357 -- 364},
  year      = {2014},
  language  = {en}
}
@article{HeinEubanksHibberdetal.2020,
  author    = {Hein, Andreas M. and Eubanks, T. Marshall and Hibberd, Adam and Fries, Dan and Schneider, Jean and Lingam, Manasvi and Kennedy, Robert and Perakis, Nikolaos and Dachwald, Bernd and Kervella, Pierre},
  title     = {Interstellar Now! Missions to and sample returns from nearby interstellar objects},
  publisher = {Elsevier},
  address   = {Amsterdam},
  pages     = {1 -- 8},
  year      = {2020},
  abstract  = {The recently discovered first high velocity hyperbolic objects passing through the Solar System, 1I/'Oumuamua and 2I/Borisov, have raised the question about near term missions to Interstellar Objects. In situ spacecraft exploration of these objects will allow the direct determination of both their structure and their chemical and isotopic composition, enabling an entirely new way of studying small bodies from outside our solar system. In this paper, we map various Interstellar Object classes to mission types, demonstrating that missions to a range of Interstellar Object classes are feasible, using existing or near-term technology. We describe flyby, rendezvous and sample return missions to interstellar objects, showing various ways to explore these bodies characterizing their surface, dynamics, structure and composition. Interstellar objects likely formed very far from the solar system in both time and space; their direct exploration will constrain their formation and history, situating them within the dynamical and chemical evolution of the Galaxy. These mission types also provide the opportunity to explore solar system bodies and perform measurements in the far outer solar system.},
  language  = {en}
}
@article{RuebbelkeVoegeleGrajewskietal.2022,
  author    = {R{\"u}bbelke, Dirk and V{\"o}gele, Stefan and Grajewski, Matthias and Zobel, Luzy},
  title     = {Hydrogen-based steel production and global climate protection: An empirical analysis of the potential role of a European cross border adjustment mechanism},
  series = {Journal of Cleaner Production},
  volume    = {380},
  journal   = {Journal of Cleaner Production},
  number    = {Part 2, Art. Nr.:135040},
  publisher = {Elsevier},
  issn      = {0959-6526},
  doi       = {10.1016/j.jclepro.2022.135040},
  year      = {2022},
  abstract  = {The European Union's aim to become climate neutral by 2050 necessitates ambitious efforts to reduce carbon emissions. Large reductions can be attained particularly in energy intensive sectors like iron and steel. In order to prevent the relocation of such industries outside the EU in the course of tightening environmental regulations, the establishment of a climate club jointly with other large emitters and alternatively the unilateral implementation of an international cross-border carbon tax mechanism are proposed. This article focuses on the latter option choosing the steel sector as an example. In particular, we investigate the financial conditions under which a European cross border mechanism is capable to protect hydrogen-based steel production routes employed in Europe against more polluting competition from abroad. By using a floor price model, we assess the competitiveness of different steel production routes in selected countries. We evaluate the climate friendliness of steel production on the basis of specific GHG emissions. In addition, we utilize an input-output price model. It enables us to assess impacts of rising cost of steel production on commodities using steel as intermediates. Our results raise concerns that a cross-border tax mechanism will not suffice to bring about competitiveness of hydrogen-based steel production in Europe because the cost tends to remain higher than the cost of steel production in e.g. China. Steel is a classic example for a good used mainly as intermediate for other products. Therefore, a cross-border tax mechanism for steel will increase the price of products produced in the EU that require steel as an input. This can in turn adversely affect competitiveness of these sectors. Hence, the effects of higher steel costs on European exports should be borne in mind and could require the cross-border adjustment mechanism to also subsidize exports.},
  language  = {en}
}
@article{EngelBayerHoltmannetal.2019,
  author    = {Engel, Mareike and Bayer, Hendrik and Holtmann, Dirk and Tippk{\"o}tter, Nils and Ulber, Roland},
  title     = {Flavin secretion of Clostridium acetobutylicum in a bioelectrochemical system - Is an iron limitation involved?},
  series = {Bioelectrochemistry},
  journal   = {Bioelectrochemistry},
  number    = {In Press, Accepted Manuscript},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1567-5394},
  doi       = {10.1016/j.bioelechem.2019.05.014},
  year      = {2019},
  language  = {en}
}
@article{KronhardtAlexopoulosReisseletal.2014,
  author    = {Kronhardt, Valentina and Alexopoulos, Spiros and Reißel, Martin and Sattler, Johannes Christoph and Hoffschmidt, Bernhard and H{\"a}nel, Matthias and Doerbeck, Till},
  title     = {High-temperature thermal storage system for solar tower power plants with open-volumetric air receiver simulation and energy balancing of a discretized model},
  series = {Energy procedia},
  volume    = {49},
  journal   = {Energy procedia},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1876-6102 (E-Journal) ; 1876-6102 (Print)},
  doi       = {10.1016/j.egypro.2014.03.094},
  pages     = {870 -- 877},
  year      = {2014},
  abstract  = {This paper describes the modeling of a high-temperature storage system for an existing solar tower power plant with open volumetric receiver technology, which uses air as heat transfer medium (HTF). The storage system model has been developed in the simulation environment Matlab/Simulink®. The storage type under investigation is a packed bed thermal energy storage system which has the characteristics of a regenerator. Thermal energy can be stored and discharged as required via the HTF air. The air mass flow distribution is controlled by valves, and the mass flow by two blowers. The thermal storage operation strategy has a direct and significant impact on the energetic and economic efficiency of the solar tower power plants.},
  language  = {en}
}
@article{OertelBung2015,
  author    = {Oertel, Mario and Bung, Daniel Bernhard},
  title     = {Stability and scour development of bed material on crossbar block ramps},
  series = {International journal of sediment research},
  volume    = {30},
  journal   = {International journal of sediment research},
  number    = {4},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1001-6279},
  doi       = {10.1016/j.ijsrc.2014.12.003},
  pages     = {344 -- 350},
  year      = {2015},
  abstract  = {Block ramps are ecologically oriented drop structures with adequate energy dissipation and partially moderate flow velocities. A special case is given with crossbar block ramps, where the upstream and downstream level difference is reduced by a series of basins. To prevent the total structure from failing, the stability of single boulders within the crossbars and the bed material in between must be guaranteed. The present paper addresses the stability of bed material and scour development for various flow regimes. Any bed material erosion may affect the stability of the crossbar boulders, which in turn can result in major damages of the ramp. Therefore new design approaches are developed to choose an appropriate bed material size and to avoid failures of crossbar block ramp structures.},
  language  = {en}
}
@article{SchaelAtanasyanBerdugoetal.2019,
  author    = {Schael, S. and Atanasyan, A. and Berdugo, J. and Bretz, T. and Czupalla, Markus and Dachwald, Bernd and Doetinchem, P. von and Duranti, M. and Gast, H. and Karpinski, W. and Kirn, T. and L{\"u}belsmeyer, K. and Ma{\~n}a, C. and Marrocchesi, P.S. and Mertsch, P. and Moskalenko, I.V. and Schervan, T. and Schluse, M. and Schr{\"o}der, K.-U. and Schultz von Dratzig, A. and Senatore, C. and Spies, L. and Wakely, S.P. and Wlochal, M. and Uglietti, D. and Zimmermann, J.},
  title     = {AMS-100: The next generation magnetic spectrometer in space - An international science platform for physics and astrophysics at Lagrange point 2},
  series = {Nuclear Instruments and Methods in Physics Research Section A: Accelerators, Spectrometers, Detectors and Associated Equipment},
  volume    = {944},
  journal   = {Nuclear Instruments and Methods in Physics Research Section A: Accelerators, Spectrometers, Detectors and Associated Equipment},
  number    = {162561},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0168-9002},
  doi       = {10.1016/j.nima.2019.162561},
  year      = {2019},
  language  = {en}
}
@article{GrajewskiHronTurek2005,
  author    = {Grajewski, Matthias and Hron, Jaroslav and Turek, Stefan},
  title     = {Dual weighted a posteriori error estimation for a new nonconforming linear finite element on quadrilaterals},
  series = {Applied Numerical Mathematics},
  volume    = {54},
  journal   = {Applied Numerical Mathematics},
  number    = {3-4},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0168-9274},
  doi       = {10.1016/j.apnum.2004.09.016},
  pages     = {504 -- 518},
  year      = {2005},
  abstract  = {After a short introduction of a new nonconforming linear finite element on quadrilaterals recently developed by Park, we derive a dual weighted residual-based a posteriori error estimator (in the sense of Becker and Rannacher) for this finite element. By computing a corresponding dual solution we estimate the error with respect to a given target error functional. The reliability and efficiency of this estimator is analyzed in several numerical experiments.},
  language  = {en}
}
@article{DefosseKleinschmidtSchmutzetal.2022,
  author    = {Defosse, Jerome and Kleinschmidt, Joris and Schmutz, Axel and Loop, Torsten and Staat, Manfred and Gatzweiler, Karl-Heinz and Wappler, Frank and Schieren, Mark},
  title     = {Dental strain on maxillary incisors during tracheal intubation with double-lumen tubes and different laryngoscopy techniques - a blinded manikin study},
  series = {Journal of Cardiothoracic and Vascular Anesthesia},
  volume    = {36},
  journal   = {Journal of Cardiothoracic and Vascular Anesthesia},
  number    = {8, Part B},
  publisher = {Elsevier},
  address   = {New York, NY},
  issn      = {1053-0770},
  doi       = {10.1053/j.jvca.2022.02.017},
  pages     = {3021 -- 3027},
  year      = {2022},
  language  = {en}
}