@article{DroopChenRadfordetal.2023,
  author    = {Droop, Philipp and Chen, Shaohuang and Radford, Melissa J. and Paulßen, Elisabeth and Gates, Byron D. and Reilly, Raymond M. and Radchenko, Valery and Hoehr, Cornelia},
  title     = {Synthesis of 197m/gHg labelled gold nanoparticles for targeted radionuclide therapy},
  series = {Radiochimica Acta},
  volume    = {111},
  journal   = {Radiochimica Acta},
  number    = {10},
  publisher = {De Gruyter},
  address   = {Berlin [u.a.]},
  issn      = {2193-3405},
  doi       = {10.1515/ract-2023-0144},
  pages     = {773 -- 779},
  year      = {2023},
  abstract  = {Meitner-Auger-electron emitters have a promising potential for targeted radionuclide therapy of cancer because of their short range and the high linear energy transfer of Meitner-Auger-electrons (MAE). One promising MAE candidate is 197m/gHg with its half-life of 23.8 h and 64.1 h, respectively, and high MAE yield. Gold nanoparticles (AuNPs) that are labelled with 197m/gHg could be a helpful tool for radiation treatment of glioblastoma multiforme when infused into the surgical cavity after resection to prevent recurrence. To produce such AuNPs, 197m/gHg was embedded into pristine AuNPs. Two different syntheses were tested starting from irradiated gold containing trace amounts of 197m/gHg. When sodium citrate was used as reducing agent, no 197m/gHg labelled AuNPs were formed, but with tannic acid, 197m/gHg labeled AuNPs were produced. The method was optimized by neutralizing the pH (pH = 7) of the Au/197m/gHg solution, which led to labelled AuNPs with a size of 12.3 ± 2.0 nm as measured by transmission electron microscopy. The labelled AuNPs had a concentration of 50 μg (gold)/mL with an activity of 151 ± 93 kBq/mL (197gHg, time corrected to the end of bombardment).},
  language  = {en}
}
@article{BhattaraiJabbariAndingetal.2018,
  author    = {Bhattarai, Aroj and Jabbari, Medisa and Anding, Ralf and Staat, Manfred},
  title     = {Surgical treatment of vaginal vault prolapse using different prosthetic mesh implants: a finite element analysis},
  series = {tm - Technisches Messen},
  volume    = {85},
  journal   = {tm - Technisches Messen},
  number    = {5},
  publisher = {De Gruyter},
  address   = {Berlin},
  issn      = {2196-7113},
  doi       = {10.1515/teme-2017-0115},
  pages     = {331 -- 342},
  year      = {2018},
  abstract  = {Particularly multiparous elderly women may suffer from vaginal vault prolapse after hysterectomy due to weak support from lax apical ligaments. A decreased amount of estrogen and progesterone in older age is assumed to remodel the collagen thereby reducing tissue stiffness. Sacrocolpopexy is either performed as open or laparoscopic surgery using prosthetic mesh implants to substitute lax ligaments. Y-shaped mesh models (DynaMesh, Gynemesh, and Ultrapro) are implanted in a 3D female pelvic floor finite element model in the extraperitoneal space from the vaginal cuff to the first sacral (S1) bone below promontory. Numerical simulations are conducted during Valsalva maneuver with weakened tissues modeled by reduced tissue stiffness. Tissues are modeled as incompressible, isotropic hyperelastic materials whereas the meshes are modeled either as orthotropic linear elastic or as isotropic hyperlastic materials. The positions of the vaginal cuff and the bladder base are calculated from the pubococcygeal line for female pelvic floor at rest, for prolapse and after repair using the three meshes. Due to mesh mechanics and mesh pore deformation along the loaded direction, the DynaMesh with regular rectangular mesh pores is found to provide better mechanical support to the organs than the Gynemesh and the Ultrapro with irregular hexagonal mesh pores. Insbesondere {\"a}ltere, mehrgeb{\"a}hrende Frauen leiden h{\"a}ufiger an einem Scheidenvorfall nach einer Hysterektomie aufgrund der schwachen Unterst{\"u}tzung durch laxe apikale B{\"a}nder. Es wird angenommen, dass eine verringerte Menge an {\"O}strogen und Progesteron im h{\"o}heren Alter das Kollagen umformt, wodurch die Gewebesteifigkeit reduziert wird. Die Sakrokolpopexie ist eine offene oder laparoskopische Operation, die mit prothetischen Netzimplantaten durchgef{\"u}hrt wird, um laxe B{\"a}nder zu ersetzen. Y-f{\"o}rmige Netzmodelle (DynaMesh, Gynemesh und Ultrapro) werden in einem 3D-Modell des weiblichen Beckenbodens im extraperitonealen Raum vom Vaginalstumpf bis zum Promontorium implantiert. Numerische Simulationen werden w{\"a}hrend des Valsalva-Man{\"o}vers mit geschw{\"a}chtem Gewebe durchgef{\"u}hrt, das durch eine reduzierte Gewebesteifigkeit modelliert wird. Die Gewebe werden als inkompressible, isotrop hyperelastische Materialien modelliert, w{\"a}hrend die Netze entweder als orthotrope linear elastische oder als isotrope hyperlastische Materialien modelliert werden. Die Positionen des Vaginalstumpfs, der Blase und der Harnr{\"o}hrenachse werden anhand der Pubococcygeallinie aus der Ruhelage, f{\"u}r den Prolaps und nach der Reparatur unter Verwendung der drei Netze berechnet. Aufgrund der Netzmechanik und der Netzporenverformung bietet das DynaMesh mit regelm{\"a}ßigen rechteckigen Netzporen eine bessere mechanische Unterst{\"u}tzung und eine Neupositionierung des Scheidengew{\"o}lbes, der Blase und der Urethraachse als Gynemesh und Ultrapro mit unregelm{\"a}ßigen hexagonalen Netzporen.},
  language  = {en}
}
@article{FrotscherStaat2014,
  author    = {Frotscher, Ralf and Staat, Manfred},
  title     = {Stresses produced by different textile mesh implants in a tissue equivalent},
  series = {BioNanoMaterials},
  volume    = {15},
  journal   = {BioNanoMaterials},
  number    = {1-2},
  publisher = {De Gruyter},
  address   = {Berlin},
  issn      = {2191-4672 (E-Journal); 2193-066X (E-Journal); 0011-8656 (Print); 1616-0177 (Print); 2193-0651 (Print)},
  doi       = {10.1515/bnm-2014-0003},
  pages     = {25 -- 30},
  year      = {2014},
  abstract  = {Two single-incision mini-slings used for treating urinary incontinence in women are compared with respect to the stresses they produce in their surrounding tissue. In an earlier paper we experimentally observed that these implants produce considerably different stress distributions in a muscle tissue equivalent. Here we perform 2D finite element analyses to compare the shear stresses and normal stresses in the tissue equivalent for the two meshes and to investigate their failure behavior. The results clearly show that the Gynecare TVT fails for increasing loads in a zipper-like manner because it gradually debonds from the surrounding tissue. Contrary to that, the tissue at the ends of the DynaMesh-SIS direct may rupture but only at higher loads. The simulation results are in good agreement with the experimental observations thus the computational model helps to interpret the experimental results and provides a tool for qualitative evaluation of mesh implants.},
  language  = {en}
}
@article{Weigand2012,
  author    = {Weigand, Christoph},
  title     = {Statistical Tests Based on Reliability and Precision},
  series = {Economic Quality Control : EQC ; international journal for quality and reliability},
  volume    = {27},
  journal   = {Economic Quality Control : EQC ; international journal for quality and reliability},
  number    = {1},
  publisher = {De Gruyter},
  address   = {Berlin},
  issn      = {1869-6147},
  doi       = {10.1515/eqc-2012-0002},
  pages     = {43 -- 64},
  year      = {2012},
  abstract  = {The construction of a statistical test is investigated which is based only on "reliability" and "precision" as quality criteria. The reliability of a statistical test is quantifiedin a straightforward way by the probability that the decision of the test is correct. However, the quantification of the precision of a statistical test is not at all evident. Thereforethe paper presents and discusses several approaches. Moreover the distinction of "nullhypothesis" and "alternative hypothesis" is not necessary any longer.},
  language  = {en}
}
@article{GazdaMaurischat2020,
  author    = {Gazda, Quentin and Maurischat, Andreas},
  title     = {Special functions and Gauss-Thakur sums in higher rank and dimension},
  publisher = {De Gruyter},
  address   = {Berlin},
  pages     = {26 Seiten},
  year      = {2020},
  language  = {en}
}
@article{BerndtGattnerZahn1975,
  author    = {Berndt, Heinz and Gattner, Hans-Gregor and Zahn, Helmut},
  title     = {Semisynthetisches Des-A1-glycin-Schafinsulin},
  series = {Biological Chemistry},
  volume    = {356},
  journal   = {Biological Chemistry},
  number    = {2},
  publisher = {De Gruyter},
  address   = {Berlin},
  issn      = {1437-4315},
  doi       = {10.1515/bchm2.1975.356.2.1455},
  pages     = {1469 -- 1472},
  year      = {1975},
  language  = {de}
}
@incollection{CzarneckiFettke2021,
  author    = {Czarnecki, Christian and Fettke, Peter},
  title     = {Robotic process automation : Positioning, structuring, and framing the work},
  series = {Robotic process automation : Management, technology, applications},
  booktitle = {Robotic process automation : Management, technology, applications},
  editor    = {Czarnecki, Christian and Fettke, Peter},
  publisher = {De Gruyter},
  address   = {Oldenbourg},
  isbn      = {978-3-11-067668-6 (Print)},
  doi       = {10.1515/9783110676693-202},
  pages     = {3 -- 24},
  year      = {2021},
  abstract  = {Robotic process automation (RPA) has attracted increasing attention in research and practice. This chapter positions, structures, and frames the topic as an introduction to this book. RPA is understood as a broad concept that comprises a variety of concrete solutions. From a management perspective RPA offers an innovative approach for realizing automation potentials, whereas from a technical perspective the implementation based on software products and the impact of artificial intelligence (AI) and machine learning (ML) are relevant. RPA is industry-independent and can be used, for example, in finance, telecommunications, and the public sector. With respect to RPA this chapter discusses definitions, related approaches, a structuring framework, a research framework, and an inside as well as outside architectural view. Furthermore, it provides an overview of the book combined with short summaries of each chapter.},
  language  = {en}
}
@article{KolditzAlbinBrueggemannetal.2016,
  author    = {Kolditz, Melanie and Albin, Thivaharan and Br{\"u}ggemann, Gert-Peter and Abel, Dirk and Albracht, Kirsten},
  title     = {Robotergest{\"u}tztes System f{\"u}r ein verbessertes neuromuskul{\"a}res Aufbautraining der Beinstrecker},
  series = {at - Automatisierungstechnik},
  volume    = {64},
  journal   = {at - Automatisierungstechnik},
  number    = {11},
  publisher = {De Gruyter},
  address   = {Berlin},
  issn      = {2196-677X},
  doi       = {10.1515/auto-2016-0044},
  pages     = {905 -- 914},
  year      = {2016},
  abstract  = {Neuromuskul{\"a}res Aufbautraining der Beinstrecker ist ein wichtiger Bestandteil in der Rehabilitation und Pr{\"a}vention von Muskel-Skelett-Erkrankungen. Effektives Training erfordert hohe Muskelkr{\"a}fte, die gleichzeitig hohe Belastungen von bereits gesch{\"a}digten Strukturen bedeuten. Um trainingsinduzierte Sch{\"a}digungen zu vermeiden, m{\"u}ssen diese Kr{\"a}fte kontrolliert werden. Mit heutigen Trainingsger{\"a}ten k{\"o}nnen diese Ziele allerdings nicht erreicht werden. F{\"u}r ein sicheres und effektives Training sollen durch den Einsatz der Robotik, Sensorik, eines Regelkreises sowie Muskel-Skelett-Modellen Belastungen am Zielgewebe direkt berechnet und kontrolliert werden. Auf Basis zweier Vorstudien zu m{\"o}glichen Stellgr{\"o}ßen wird der Aufbau eines robotischen Systems vorgestellt, das sowohl f{\"u}r Forschungszwecke als auch zur Entwicklung neuartiger Trainingsger{\"a}te verwendet werden kann.},
  language  = {de}
}
@incollection{Wilke2017,
  author    = {Wilke, Thomas},
  title     = {Ranson, Pierre},
  series = {Allgemeines K{\"u}nstler-Lexikon. Online},
  booktitle = {Allgemeines K{\"u}nstler-Lexikon. Online},
  publisher = {De Gruyter},
  address   = {Berlin},
  year      = {2017},
  language  = {de}
}
@incollection{KurbelPietsch1989,
  author    = {Kurbel, Karl and Pietsch, Wolfram},
  title     = {Projektmanagementebenen bei evolution{\"a}rer Softwareentwicklung},
  series = {Interaktive betriebswirtschaftliche Informations- und Steuerungssysteme},
  booktitle = {Interaktive betriebswirtschaftliche Informations- und Steuerungssysteme},
  editor    = {Kurbel, Karl and Mertens, Peter and Scheer, August W.},
  publisher = {De Gruyter},
  address   = {Berlin},
  isbn      = {3-11-012100-X},
  doi       = {10.1515/9783110847055-013},
  pages     = {261 -- 285},
  year      = {1989},
  language  = {de}
}