@article{DigelWehlitzKayseretal.2018,
  author    = {Digel, Ilya and Wehlitz, V. and Kayser, Peter and Figiel-Lange, A. and Bassam, R. and Rundstedt, F. von},
  title     = {Suspension depletion approach for exemption of infected Solanum jasminoides cells from pospiviroids},
  series = {Plant Pathology},
  volume    = {67},
  journal   = {Plant Pathology},
  number    = {2},
  publisher = {Wiley},
  address   = {Oxford},
  issn      = {1365-3059},
  doi       = {10.1111/ppa.12750},
  pages     = {358 -- 365},
  year      = {2018},
  abstract  = {Despite numerous studies, viroid elimination from infected plants remains a very challenging task. This study introduces for the first time a novel 'suspension depletion' approach for exemption of Solanum jasminoides plants from viroids. The proposed method implies initial establishment of suspension cultures of the infected plant cells. The suspended cells were then physically treated (mild thermotherapy, 33 °C), which presumably delayed the replication of the viroid. The viroid concentration in the treated biomass was monitored weekly using pospiviroid-specific PCR. After 10-12 weeks of continuous treatment, a sufficient decrease in viroid concentration was observed such that the infection became undetectable by PCR. The treated single cells then gave rise to microcolonies on a solid culture medium and the obtained viroid-negative clones were further promoted to regenerate into viroid-free plants. Three years of accumulated experimental data suggests feasibility, broad applicability, and good efficacy of the proposed approach.},
  language  = {en}
}
@article{EngelGemuendeHoltmannetal.2019,
  author    = {Engel, Mareike and Gem{\"u}nde, Andre and Holtmann, Dirk and M{\"u}ller-Renno, Christine and Ziegler, Christiane and Tippk{\"o}tter, Nils and Ulber, Roland},
  title     = {Clostridium acetobutylicum's connecting world: cell appendage formation in bioelectrochemical systems},
  series = {ChemElectroChem},
  journal   = {ChemElectroChem},
  number    = {Accepted Article},
  publisher = {Wiley},
  address   = {Weinheim},
  issn      = {2196-0216},
  doi       = {10.1002/celc.201901656},
  year      = {2019},
  language  = {en}
}
@article{NoureddineKraffLaddetal.2019,
  author    = {Noureddine, Yacine and Kraff, Oliver and Ladd, Mark E. and Wrede, Karsten and Chen, Bixia and Quick, Harald H. and Schaefers, Georg and Bitz, Andreas},
  title     = {Radiofrequency induced heating around aneurysm clips using a generic birdcage head coil at 7 Tesla under consideration of the minimum distance to decouple multiple aneurysm clips},
  series = {Magnetic Resonance in Medicine},
  journal   = {Magnetic Resonance in Medicine},
  number    = {Early view},
  publisher = {Wiley},
  address   = {Weinheim},
  issn      = {1522-2594},
  doi       = {10.1002/mrm.27835},
  pages     = {1 -- 17},
  year      = {2019},
  language  = {en}
}
@article{DrummEmhardtKoketal.2020,
  author    = {Drumm, Christian and Emhardt, Selina N. and Kok, Ellen M. and Jarodzka, Halzka and Brand-Gruwel, Saskia and van Gog, Tamara},
  title     = {How Experts Adapt Their Gaze Behavior When Modeling a Task to Novices},
  series = {Cognitive science},
  volume    = {44},
  journal   = {Cognitive science},
  number    = {9},
  publisher = {Wiley},
  address   = {Weinheim},
  issn      = {1551-6709},
  doi       = {10.1111/cogs.12893},
  pages     = {26},
  year      = {2020},
  abstract  = {Domain experts regularly teach novice students how to perform a task. This often requires them to adjust their behavior to the less knowledgeable audience and, hence, to behave in a more didactic manner. Eye movement modeling examples (EMMEs) are a contemporary educational tool for displaying experts' (natural or didactic) problem-solving behavior as well as their eye movements to learners. While research on expert-novice communication mainly focused on experts' changes in explicit, verbal communication behavior, it is as yet unclear whether and how exactly experts adjust their nonverbal behavior. This study first investigated whether and how experts change their eye movements and mouse clicks (that are displayed in EMMEs) when they perform a task naturally versus teach a task didactically. Programming experts and novices initially debugged short computer codes in a natural manner. We first characterized experts' natural problem-solving behavior by contrasting it with that of novices. Then, we explored the changes in experts' behavior when being subsequently instructed to model their task solution didactically. Experts became more similar to novices on measures associated with experts' automatized processes (i.e., shorter fixation durations, fewer transitions between code and output per click on the run button when behaving didactically). This adaptation might make it easier for novices to follow or imitate the expert behavior. In contrast, experts became less similar to novices for measures associated with more strategic behavior (i.e., code reading linearity, clicks on run button) when behaving didactically.},
  language  = {en}
}
@article{HentschkeHagerHojdis2014,
  author    = {Hentschke, Reinhard and Hager, Jonathan and Hojdis, Nils},
  title     = {Molecular Modeling Approach to the Prediction of Mechanical Properties of Silica-Reinforced Rubbers},
  series = {Journal of Applied Polymer Science},
  volume    = {131},
  journal   = {Journal of Applied Polymer Science},
  number    = {18},
  publisher = {Wiley},
  address   = {New York, NY},
  issn      = {1097-4628},
  doi       = {10.1002/app.40806},
  pages     = {1 -- 9},
  year      = {2014},
  abstract  = {Recently, we have suggested a nanomechanical model for dissipative loss in filled elastomer networks in the context of the Payne effect. The mechanism is based on a total interfiller particle force exhibiting an intermittent loop, due to the combination of short-range repulsion and dispersion forces with a long-range elastic attraction. The sum of these forces leads, under external strain, to a spontaneous instability of "bonds" between the aggregates in a filler network and attendant energy dissipation. Here, we use molecular dynamics simulations to obtain chemically realistic forces between surface modified silica particles. The latter are combined with the above model to estimate the loss modulus and the low strain storage modulus in elastomers containing the aforementioned filler-compatibilizer systems. The model is compared to experimental dynamic moduli of silica filled rubbers. We find good agreement between the model predictions and the experiments as function of the compatibilizer's molecular structure and its bulk concentration.},
  language  = {en}
}
@article{ReisertSchneiderGeissleretal.2013,
  author    = {Reisert, Steffen and Schneider, Benno and Geissler, Hanno and Gompel, Matthias van and Wagner, Patrick and Sch{\"o}ning, Michael Josef},
  title     = {Multi-sensor chip for the investigation of different types of metal oxides for the detection of H2O2 in the ppm range},
  series = {physica status solidi (a)},
  volume    = {210},
  journal   = {physica status solidi (a)},
  number    = {5},
  publisher = {Wiley},
  address   = {Weinheim},
  issn      = {1862-6319},
  pages     = {898 -- 904},
  year      = {2013},
  abstract  = {In this work, a multi-sensor chip for the investigation of the sensing properties of different types of metal oxides towards hydrogen peroxide in the ppm range is presented. The fabrication process and physical characterization of the multi-sensor chip are described. Pure SnO2 and WO3 as well as Pd- and Pt-doped SnO2 films are characterized in terms of their sensitivity to H2O2. The sensing films have been prepared by drop-coating of water-dispensed nano-powders. A physical characterization, including scanning electron microscopy and X-ray diffraction analysis of the deposited metal-oxide films, was done. From the measurements in hydrogen peroxide atmosphere, it could be shown, that all of the tested metal oxide films are suitable for the detection of H2O2 in the ppm range. The highest sensitivity and reproducibility was achieved using Pt-doped SnO2. Calibration plot of a SnO2, WO3, Pt-, and Pd-doped SnO2 gas sensor for H2O2 concentrations in the ppm range.},
  language  = {en}
}
@article{FaganBitzBjoerkmanBurtscheretal.2021,
  author    = {Fagan, Andrew J. and Bitz, Andreas and Bj{\"o}rkman-Burtscher, Isabella M. and Collins, Christopher M. and Kimbrell, Vera and Raaijmakers, Alexander J. E.},
  title     = {7T MR Safety},
  series = {Journal of Magnetic Resonance Imaging (JMRI)},
  volume    = {53},
  journal   = {Journal of Magnetic Resonance Imaging (JMRI)},
  number    = {2},
  publisher = {Wiley},
  address   = {Weinheim},
  issn      = {1522-2586},
  doi       = {10.1002/jmri.27319},
  pages     = {333 -- 346},
  year      = {2021},
  language  = {en}
}
@article{ButenwegRosin2020,
  author    = {Butenweg, Christoph and Rosin, Julia},
  title     = {Seismischer Nachweis von Mauerwerksbauten in deutschen Erdbebengebieten},
  series = {Mauerwerk},
  volume    = {24},
  journal   = {Mauerwerk},
  number    = {2},
  publisher = {Wiley},
  address   = {Weinheim},
  issn      = {1437-1022},
  doi       = {10.1002/dama.202000006},
  pages     = {108 -- 113},
  year      = {2020},
  abstract  = {Mit finanzieller Unterst{\"u}tzung der Deutschen Gesellschaft f{\"u}r Mauerwerks- und Wohnungsbau e.V. (DGfM) und des Deutschen Instituts f{\"u}r Bautechnik in Berlin (DIBt) wurden zwei aufeinander aufbauende Forschungsvorhaben zur Verbesserung der seismischen Nachweise von Mauerwerksbauten in deutschen Erdbebengebieten durchgef{\"u}hrt. Zun{\"a}chst wurde das seismische Verhalten von drei modernen unbewehrten Mauerwerksgeb{\"a}uden in der Region Emilia Romagna in Italien w{\"a}hrend der Erdbebenserie im Jahr 2012 in Kooperation mit der Universit{\"a}t Pavia eingehend untersucht. Aufbauend auf den Erkenntnissen dieser Untersuchungen wurde ein verbessertes seismisches Bemessungskonzept f{\"u}r unbewehrte Mauerwerksbauten erarbeitet. Der Beitrag stellt die wesentlichen Ergebnisse dieser Forschungsarbeiten und deren Eingang in die Normung vor.},
  language  = {de}
}
@article{MarinkovicButenweg2020,
  author    = {Marinkovic, Marko and Butenweg, Christoph},
  title     = {Ausfachungen aus Ziegelmauerwerk in Stahlbetonrahmentragwerken unter Erdbebenbeanspruchung},
  series = {Mauerwerk},
  volume    = {24},
  journal   = {Mauerwerk},
  number    = {4},
  publisher = {Wiley},
  address   = {Weinheim},
  issn      = {1437-1022},
  doi       = {10.1002/dama.202000011},
  pages     = {194 -- 205},
  year      = {2020},
  abstract  = {Stahlbetonrahmentragwerke mit Ausfachungen aus Mauerwerk weisen nach Erdbeben h{\"a}ufig schwere Sch{\"a}den auf. Gr{\"u}nde hierf{\"u}r sind die Beanspruchungen der Ausfachungsw{\"a}nde durch die aufgezwungenen Rahmenverformungen in Wandebene und die gleichzeitig auftretenden Tr{\"a}gheitskr{\"a}fte senkrecht zur Wandebene in Kombination mit der konstruktiven Ausf{\"u}hrung des Ausfachungsmauerwerks. Die Ausfachung wird in der Regel knirsch gegen die Rahmenst{\"u}tzen gemauert, wobei der Verschluss der oberen Fuge mit M{\"o}rtel oder Montageschaum erfolgt. Dadurch kommt es im Erdbebenfall zu lokalen Interaktionen zwischen Ausfachung und Rahmen, die in der Folge zu einem Versagen einzelner Ausfachungsw{\"a}nde oder zu einem sukzessiven Versagen des Gesamtgeb{\"a}udes f{\"u}hren k{\"o}nnen. Die beobachteten Sch{\"a}den waren die Motivation daf{\"u}r, in dem europ{\"a}ischen Forschungsprojekt INSYSME f{\"u}r Stahlbetonrahmentragwerke mit Ausfachungen aus hochw{\"a}rmed{\"a}mmenden Ziegelmauerwerk innovative L{\"o}sungen zur Verbesserung des seismischen Verhaltens zu entwickeln. Der vorliegende Beitrag stellt die im Rahmen des Projekts von den deutschen Projektpartnern (Universit{\"a}t Kassel, SDA-engineering GmbH) entwickelten L{\"o}sungen vor und vergleicht deren seismisches Verhalten mit der traditionellen Ausf{\"u}hrung der Ausfachungsw{\"a}nde. Grundlage f{\"u}r den Vergleich sind statisch-zyklische Wandversuche und Simulationen auf Wandebene. Aus den Ergebnissen werden Empfehlungen f{\"u}r die erdbebensichere Auslegung von Stahlbetonrahmentragwerken mit Ausfachungen aus Ziegelmauerwerk abgeleitet.},
  language  = {de}
}
@article{BrockhausBehbahaniMurisetal.2021,
  author    = {Brockhaus, Moritz K. and Behbahani, Mehdi and Muris, Farina and Jansen, Sebastian V. and Schmitz- Rode, Thomas and Steinseifer, Ulrich and Clauser, Johanna C.},
  title     = {In vitro thrombogenicity testing of pulsatile mechanical circulatory support systems: Design and proof-of-concept},
  series = {Artificial Organs},
  volume    = {45},
  journal   = {Artificial Organs},
  number    = {12},
  publisher = {Wiley},
  address   = {Weinheim},
  issn      = {1525-1594},
  doi       = {10.1111/aor.14046},
  pages     = {1513 -- 1521},
  year      = {2021},
  abstract  = {Thrombogenic complications are a main issue in mechanical circulatory support (MCS). There is no validated in vitro method available to quantitatively assess the thrombogenic performance of pulsatile MCS devices under realistic hemodynamic conditions. The aim of this study is to propose a method to evaluate the thrombogenic potential of new designs without the use of complex in-vivo trials. This study presents a novel in vitro method for reproducible thrombogenicity testing of pulsatile MCS systems using low molecular weight heparinized porcine blood. Blood parameters are continuously measured with full blood thromboelastometry (ROTEM; EXTEM, FIBTEM and a custom-made analysis HEPNATEM). Thrombus formation is optically observed after four hours of testing. The results of three experiments are presented each with two parallel loops. The area of thrombus formation inside the MCS device was reproducible. The implantation of a filter inside the loop catches embolizing thrombi without a measurable increase of platelet activation, allowing conclusions of the place of origin of thrombi inside the device. EXTEM and FIBTEM parameters such as clotting velocity (α) and maximum clot firmness (MCF) show a total decrease by around 6\% with a characteristic kink after 180 minutes. HEPNATEM α and MCF rise within the first 180 minutes indicate a continuously increasing activation level of coagulation. After 180 minutes, the consumption of clotting factors prevails, resulting in a decrease of α and MCF. With the designed mock loop and the presented protocol we are able to identify thrombogenic hot spots inside a pulsatile pump and characterize their thrombogenic potential.},
  language  = {en}
}