@article{SattlerRoegerSchwarzboezletal.2020,
  author    = {Sattler, Johannes, Christoph and R{\"o}ger, Marc and Schwarzb{\"o}zl, Peter and Buck, Reiner and Macke, Ansgar and Raeder, Christian and G{\"o}ttsche, Joachim},
  title     = {Review of heliostat calibration and tracking control methods},
  series = {Solar Energy},
  volume    = {207},
  journal   = {Solar Energy},
  publisher = {Elsevier},
  address   = {Amsterdam},
  doi       = {10.1016/j.solener.2020.06.030},
  pages     = {110 -- 132},
  year      = {2020},
  abstract  = {Large scale central receiver systems typically deploy between thousands to more than a hundred thousand heliostats. During solar operation, each heliostat is aligned individually in such a way that the overall surface normal bisects the angle between the sun's position and the aim point coordinate on the receiver. Due to various tracking error sources, achieving accurate alignment ≤1 mrad for all the heliostats with respect to the aim points on the receiver without a calibration system can be regarded as unrealistic. Therefore, a calibration system is necessary not only to improve the aiming accuracy for achieving desired flux distributions but also to reduce or eliminate spillage. An overview of current larger-scale central receiver systems (CRS), tracking error sources and the basic requirements of an ideal calibration system is presented. Leading up to the main topic, a description of general and specific terms on the topics heliostat calibration and tracking control clarifies the terminology used in this work. Various figures illustrate the signal flows along various typical components as well as the corresponding monitoring or measuring devices that indicate or measure along the signal (or effect) chain. The numerous calibration systems are described in detail and classified in groups. Two tables allow the juxtaposition of the calibration methods for a better comparison. In an assessment, the advantages and disadvantages of individual calibration methods are presented.},
  language  = {en}
}
@article{RussGoettsche2005,
  author    = {Russ, Christel and G{\"o}ttsche, Joachim},
  title     = {Energieversorgung in Niedrigstenergie-Wohngeb{\"a}uden},
  series = {W{\"a}rme und K{\"a}lte - Energie aus Sonne und Erde : Jahrestagung des Forschungsverbunds Sonnenenergie in Kooperation mit der Landesinitiative Zukunftsenergien NRW, 22.-23.09.2005 in K{\"o}ln / [Hrsg.: Gerd Stadermann]},
  journal   = {W{\"a}rme und K{\"a}lte - Energie aus Sonne und Erde : Jahrestagung des Forschungsverbunds Sonnenenergie in Kooperation mit der Landesinitiative Zukunftsenergien NRW, 22.-23.09.2005 in K{\"o}ln / [Hrsg.: Gerd Stadermann]},
  publisher = {FVS},
  address   = {Berlin},
  pages     = {93 -- 98},
  year      = {2005},
  language  = {de}
}
@article{ReisgenSchleserAbdurakhmanovetal.2012,
  author    = {Reisgen, Uwe and Schleser, Markus and Abdurakhmanov, Aydemir and Turichin, Gleb and Valdaitseva, Elena and Bach, Friedrich-Wilhelm and Hassel, Thomas and Beniyashi, Alexander},
  title     = {Investigation of factors influencing the formation of weld defects in non-vacuum electron beam welding},
  series = {The Paton welding journal},
  volume    = {2012},
  journal   = {The Paton welding journal},
  number    = {2},
  publisher = {Paton Publishing House},
  address   = {Kiev},
  issn      = {0957-798X},
  pages     = {11 -- 18},
  year      = {2012},
  abstract  = {The influence of welding condition parameters and properties of material on formation of defects, such as humping and undercuts, in non-vacuum electron beam welding was investigated. The influence of separate welding parameters on the quality of welds was determined.},
  language  = {en}
}
@article{RegerKuhnhenneHachuletal.2019,
  author    = {Reger, Vitali and Kuhnhenne, Markus and Hachul, Helmut and D{\"o}ring, Bernd and Blanke, Tobias and G{\"o}ttsche, Joachim},
  title     = {Plusenergiegeb{\"a}ude 2.0 in Stahlleichtbauweise},
  series = {Stahlbau},
  volume    = {88},
  journal   = {Stahlbau},
  number    = {6},
  publisher = {Ernst \& Sohn},
  address   = {Berlin},
  issn      = {1437-1049 (E-journal), 0038-9145 (print)},
  doi       = {10.1002/stab.201900034},
  pages     = {522 -- 528},
  year      = {2019},
  language  = {de}
}
@article{RegerKuhnhenneEbbertetal.2020,
  author    = {Reger, Vitali and Kuhnhenne, Markus and Ebbert, Thiemo and Hachul, Helmut and Blanke, Tobias and D{\"o}ring, Bernd},
  title     = {Nutzung erneuerbarer Energien durch thermische Aktivierung von Komponenten aus Stahl},
  series = {Stahlbau},
  volume    = {2020},
  journal   = {Stahlbau},
  number    = {Volume 89, Issue 6512-519},
  publisher = {Ernst \& Sohn},
  address   = {Berlin},
  issn      = {1437-1049},
  doi       = {10.1002/stab.202000031},
  pages     = {512 -- 519},
  year      = {2020},
  abstract  = {Die Versorgung von Neubauten soll m{\"o}glichst weitgehend unabh{\"a}ngig von fossilen Energietr{\"a}gern erfolgen. Erneuerbare Energien spielen daf{\"u}r eine gewichtige Rolle. Eine gute M{\"o}glichkeit, erneuerbare Energien ohne viel zus{\"a}tzlichen Aufwand nutzbar zu machen, ist, bereits vorhandenen Komponenten im Geb{\"a}ude zus{\"a}tzliche Funktionen zu geben. Hier kann bspw. die Fassade oder das Dach solarthermisch aktiviert oder durch Fotovoltaikmodule erg{\"a}nzt werden. Auch Tiefgr{\"u}ndungen k{\"o}nnen neben der statischen Funktion noch eine geothermische Funktion zur Aufnahme oder Abgabe von W{\"a}rme erhalten. Neben der Erzeugung bietet sich auch f{\"u}r die Verteilung der W{\"a}rme oder K{\"a}lte im Geb{\"a}ude die Integration in Bauteile an. Hier kann bspw. der Boden durch eine Fußbodenheizung oder die Decke durch Deckenstrahlplatten aktiviert werden. Im Rahmen der Ver{\"o}ffentlichung wird auf die thermische Aktivierung von Stahlkomponenten eingegangen. Es wird eine L{\"o}sung vorgestellt, die vorgeh{\"a}ngte hinterl{\"u}ftete Stahlfassade (VHF) solarthermisch zu aktivieren. Außerdem werden zwei M{\"o}glichkeiten zur geothermischen Aktivierung von Tiefgr{\"u}ndungen mittels Stahlpf{\"a}hlen gezeigt. Zuletzt wird ein System zur thermischen Aktivierung von Stahltrapezprofilen an der Decke erl{\"a}utert, welches W{\"a}rme zuf{\"u}hren oder bei Bedarf abf{\"u}hren kann.},
  language  = {de}
}
@article{RauAlexopoulosBreitbachetal.2014,
  author    = {Rau, Christoph and Alexopoulos, Spiros and Breitbach, Gerd and Hoffschmidt, Bernhard and Latzke, Markus and Sattler, Johannes, Christoph},
  title     = {Transient simulation of a solar-hybrid tower power plant with open volumetric receiver at the location Barstow},
  series = {Energy procedia : proceedings of the SolarPACES 2013 International Conference},
  volume    = {49},
  journal   = {Energy procedia : proceedings of the SolarPACES 2013 International Conference},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1876-6102},
  doi       = {10.1016/j.egypro.2014.03.157},
  pages     = {1481 -- 1490},
  year      = {2014},
  abstract  = {In this work the transient simulations of four hybrid solar tower power plant concepts with open-volumetric receiver technology for a location in Barstow-Daggett, USA, are presented. The open-volumetric receiver uses ambient air as heat transfer fluid and the hybridization is realized with a gas turbine. The Rankine cycle is heated by solar-heated air and/or by the gas turbine's flue gases. The plant can be operated in solar-only, hybrid parallel or combined cycle-only mode as well as in any intermediate load levels where the solar portion can vary between 0 to 100\%. The simulated plant is based on the configuration of a solar-hybrid power tower project, which is in planning for a site in Northern Algeria. The meteorological data for Barstow-Daggett was taken from the software meteonorm. The solar power tower simulation tool has been developed in the simulation environment MATLAB/Simulink and is validated.},
  language  = {en}
}
@article{PuppeGiulianoFrantzetal.2018,
  author    = {Puppe, Michael and Giuliano, Stefano and Frantz, Cathy and Uhlig, Ralf and Schumacher, Ralph and Ibraheem, Wagdi and Schmalz, Stefan and Waldmann, Barbara and Guder, Christoph and Peter, Dennis and Schwager, Christian and Teixeira Boura, Cristiano Jos{\´e} and Alexopoulos, Spiros and Spiegel, Michael and Wortmann, J{\"u}rgen and Hinrichs, Matthias and Engelhard, Manfred and Aust, Michael},
  title     = {Techno-economic optimization of molten salt solar tower plants},
  series = {AIP Conference Proceedings art.no. 040033},
  volume    = {2033},
  journal   = {AIP Conference Proceedings art.no. 040033},
  number    = {Issue 1},
  publisher = {AIP Publishing},
  address   = {Melville, NY},
  doi       = {10.1063/1.5067069},
  year      = {2018},
  abstract  = {In this paper the results of a techno-economic analysis of improved and optimized molten salt solar tower plants (MSSTP plants) are presented. The potential improvements that were analyzed include different receiver designs, different designs of the HTF-system and plant control, increased molten salt temperatures (up to 640°C) and multi-tower systems. Detailed technological and economic models of the solar field, solar receiver and high temperature fluid system (HTF-system) were developed and used to find potential improvements compared to a reference plant based on Solar Two technology and up-to-date cost estimations. The annual yield model calculates the annual outputs and the LCOE of all variants. An improved external tubular receiver and improved HTF-system achieves a significant decrease of LCOE compared to the reference. This is caused by lower receiver cost as well as improvements of the HTF-system and plant operation strategy, significantly reducing the plant own consumption. A novel star receiver shows potential for further cost decrease. The cavity receiver concepts result in higher LCOE due to their high investment cost, despite achieving higher efficiencies. Increased molten salt temperatures seem possible with an adapted, closed loop HTF-system and achieve comparable results to the original improved system (with 565°C) under the given boundary conditions. In this analysis all multi tower systems show lower economic viability compared to single tower systems, caused by high additional cost for piping connections and higher cost of the receivers. REFERENCES},
  language  = {en}
}
@article{PeereBlanke2022,
  author    = {Peere, Wouter and Blanke, Tobias},
  title     = {GHEtool: An open-source tool for borefield sizing in Python},
  series = {Journal of Open Source Software},
  volume    = {7},
  journal   = {Journal of Open Source Software},
  number    = {76},
  editor    = {Vernon, Chris},
  issn      = {2475-9066},
  doi       = {10.21105/joss.04406},
  pages     = {1 -- 4, 4406},
  year      = {2022},
  abstract  = {GHEtool is a Python package that contains all the functionalities needed to deal with borefield design. It is developed for both researchers and practitioners. The core of this package is the automated sizing of borefield under different conditions. The sizing of a borefield is typically slow due to the high complexity of the mathematical background. Because this tool has a lot of precalculated data, GHEtool can size a borefield in the order of tenths of milliseconds. This sizing typically takes the order of minutes. Therefore, this tool is suited for being implemented in typical workflows where iterations are required. GHEtool also comes with a graphical user interface (GUI). This GUI is prebuilt as an exe-file because this provides access to all the functionalities without coding. A setup to install the GUI at the user-defined place is also implemented and available at: https://www.mech.kuleuven.be/en/tme/research/thermal_systems/tools/ghetool.},
  language  = {en}
}
@article{MeyerHaenelBeehetal.2020,
  author    = {Meyer, S. and H{\"a}nel, Matthias and Beeh, B. and Dittmann-Gabriel, S{\"o}ren and Dluhosch, R. and May, Martin and Herrmann, Ulf and [und 5 weitere],},
  title     = {Multifunktionaler thermischer Stromspeicher f{\"u}r die Strom- und W{\"a}rmeversorgung der Industrie von morgen},
  series = {ETG Journal / Energietechnische Gesellschaft im VDE (ETG)},
  volume    = {2020},
  journal   = {ETG Journal / Energietechnische Gesellschaft im VDE (ETG)},
  number    = {1},
  issn      = {2625-9907},
  pages     = {6 -- 9},
  year      = {2020},
  language  = {de}
}
@article{MelissWindheim1977,
  author    = {Meliß, Michael and Windheim, R.},
  title     = {Energiequelle f{\"u}r morgen : M{\"o}glichkeiten und Grenzen der Windenergienutzung - ein Statusbericht},
  series = {VDI-Nachrichten. Bd. 31 (1977), H. 22},
  journal   = {VDI-Nachrichten. Bd. 31 (1977), H. 22},
  issn      = {0042-1758},
  pages     = {37 -- 38},
  year      = {1977},
  language  = {de}
}