@article{Huening2012,
  author    = {H{\"u}ning, Felix},
  title     = {Using Trench PowerMOSFETs in Linear Mode},
  series = {Power Electronics Europe (2012)},
  journal   = {Power Electronics Europe (2012)},
  publisher = {DFA Media},
  address   = {Tonbridge},
  issn      = {1748-3530},
  pages     = {27 -- 29},
  year      = {2012},
  abstract  = {If we think about applications for modern Power MOSFETs using trench technology, running them in linear mode may not be top of the priority list. Yet there are multiple uses for Trench Power MOSFETs in linear mode. In fact, even turning the device on and off in switching applications is a form of linear operation. Also, these components can be run in linear mode to protect the device against voltage surges. This article will illustrate the factors that need to be considered for linear operation and show how Trench Power MOSFETs are suited to it.},
  language  = {en}
}
@inproceedings{EngelsSchnabel2012,
  author    = {Engels, Elmar and Schnabel, Holger},
  title     = {Rapid-control-prototyping of industrial drives for the sercos automation bus},
  series = {13th International Workshop on Mechatronics (MECATRONICS), 2012 9th France-Japan \& 7th Europe-Asia Congress on and Research and Education in Mechatronics (REM)},
  booktitle = {13th International Workshop on Mechatronics (MECATRONICS), 2012 9th France-Japan \& 7th Europe-Asia Congress on and Research and Education in Mechatronics (REM)},
  isbn      = {978-1-4673-4771-6},
  pages     = {177 -- 181},
  year      = {2012},
  abstract  = {This article describes the functionality of a MATLAB® library that can be used to develop motion-logic applications in MATLAB programming language for industrial drive and control systems using the well known sercos automation bus. Therewith MATLAB's functionality is extended to designing automation applications from single axis machines up to multi-kinematic robots.},
  language  = {en}
}
@inproceedings{ReisgenSchleserSchoeneetal.2012,
  author    = {Reisgen, Uwe and Schleser, Markus and Schoene, Jens and Hegger, Josef and Gallwoszus, J{\"o}rg and Feldmann, Markus and Kopp, Maik and G{\"u}ndel, Max},
  title     = {Investigation on bond mechanisms of innovative small-scale shear connectors between steel and concrete},
  series = {Bond in concrete 2012. Vol. 2. Bond in new materials and under severe conditions},
  booktitle = {Bond in concrete 2012. Vol. 2. Bond in new materials and under severe conditions},
  editor    = {Cairns, John W.},
  publisher = {Publisher creations},
  address   = {Manerbio, Brescia},
  isbn      = {978-88-907078-3-4},
  pages     = {893 -- 898},
  year      = {2012},
  language  = {en}
}
@article{ReisgenSchleserMokrovetal.2012,
  author    = {Reisgen, Uwe and Schleser, Markus and Mokrov, Oleg and Ahmed, Essam},
  title     = {Statistical modeling of laser welding of DP/TRIP steel sheets},
  series = {Optics and laser technology},
  volume    = {44},
  journal   = {Optics and laser technology},
  number    = {1},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1879-2545 (E-Journal); 0030-3992 (Print); 0308-4280 (Print)},
  doi       = {10.1016/j.optlastec.2011.05.025},
  pages     = {92 -- 101},
  year      = {2012},
  abstract  = {In this research work, a statistical analysis of the CO2 laser beam welding of dual phase (DP600)/transformation induced plasticity (TRIP700) steel sheets was done using response surface methodology. The analysis considered the effect of laser power (2-2.2 kW), welding speed (40-50 mm/s) and focus position (-1 to 0 mm) on the heat input, the weld bead geometry, uniaxial tensile strength, formability limited dome height and welding operation cost. The experimental design was based on Box-Behnken design using linear and quadratic polynomial equations for predicting the mathematical models. The results indicate that the proposed models predict the responses adequately within the limits of welding parameters being used and the welding speed is the most significant parameter during the welding process.},
  language  = {en}
}
@article{ReisgenSchleserMokrovetal.2012,
  author    = {Reisgen, Uwe and Schleser, Markus and Mokrov, Oleg and Ahmed, Essam},
  title     = {Optimization of laser welding of DP/TRIP steel sheets using statistical approach},
  series = {Optics and laser technology},
  volume    = {44},
  journal   = {Optics and laser technology},
  number    = {1},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1879-2545 (E-Journal); 0030-3992 (Print); 0308-4280 (Print)},
  doi       = {10.1016/j.optlastec.2011.06.028},
  pages     = {255 -- 262},
  year      = {2012},
  abstract  = {Generally, the quality of a weld joint is directly influenced by the welding input parameter settings. Selection of proper process parameters is important to obtain the desired weld bead profile and quality. In this research work, numerical and graphical optimization techniques of the CO2 laser beam welding of dual phase (DP600)/transformation induced plasticity (TRIP700) steel sheets were carried out using response surface methodology (RSM) based on Box-Behnken design. The procedure was established to improve the weld quality, increase the productivity and minimize the total operation cost by considering the welding parameters range of laser power (2-2.2 kW), welding speed (40-50 mm/s) and focus position (-1 to 0 mm). It was found that, RSM can be considered as a powerful tool in experimental welding optimization, even when the experimenter does not have a model for the process. Strong, efficient and low cost weld joints could be achieved using the optimum welding conditions.},
  language  = {en}
}
@inproceedings{QuadfliegSchoeneSchleseretal.2012,
  author    = {Quadflieg, Till and Schoene, Jens and Schleser, Markus and Jockenh{\"o}vel, Stefan and Reisgen, Uwe and Gries, Thomas},
  title     = {Shear connectors for hybrid joints of metal and FRP},
  series = {Diversity in composites : conference proceedings : Composites Australia and CRC-ACS 2012 conference},
  booktitle = {Diversity in composites : conference proceedings : Composites Australia and CRC-ACS 2012 conference},
  editor    = {Heslehurst, Rikard Benton},
  publisher = {Composites Australia},
  address   = {Hawthorne},
  isbn      = {978-0-9873285-0-2},
  pages     = {[152] -- [160]},
  year      = {2012},
  language  = {en}
}
@article{ReisgenSchleserMokrovetal.2012,
  author    = {Reisgen, Uwe and Schleser, Markus and Mokrov, Oleg and Zabirov, Alexander and F{\"u}ssel, Uwe and Schnick, Michael and Hertel, Martin and Jaeckel, Sebastian},
  title     = {Modelling and visualisation of the GMA process},
  series = {Welding and Cutting},
  volume    = {11},
  journal   = {Welding and Cutting},
  number    = {4},
  publisher = {DVS Verlag},
  address   = {D{\"u}sseldorf},
  issn      = {1612-3433},
  pages     = {242 -- 249},
  year      = {2012},
  language  = {en}
}
@inproceedings{ReisgenSchleserAbdurakhmanovetal.2012,
  author    = {Reisgen, Uwe and Schleser, Markus and Abdurakhmanov, Aydemir and Gumenyuk, Andrej},
  title     = {Application of electron beam welding to fabrication of steel-aluminium dissimilar joint},
  series = {Beam technologies \& laser application : proceedings of the VII international conference, Saint Petersburg, Sept. 18-21, 2012},
  booktitle = {Beam technologies \& laser application : proceedings of the VII international conference, Saint Petersburg, Sept. 18-21, 2012},
  publisher = {Publ. House},
  address   = {Saint Petersburg},
  pages     = {265 -- 279},
  year      = {2012},
  language  = {en}
}
@article{ReisgenSchleserAbdurakhmanovetal.2012,
  author    = {Reisgen, Uwe and Schleser, Markus and Abdurakhmanov, Aydemir and Turichin, Gleb and Valdaitseva, Elena and Bach, Friedrich-Wilhelm and Hassel, Thomas and Beniyashi, Alexander},
  title     = {Investigation of factors influencing the formation of weld defects in non-vacuum electron beam welding},
  series = {The Paton welding journal},
  volume    = {2012},
  journal   = {The Paton welding journal},
  number    = {2},
  publisher = {Paton Publishing House},
  address   = {Kiev},
  issn      = {0957-798X},
  pages     = {11 -- 18},
  year      = {2012},
  abstract  = {The influence of welding condition parameters and properties of material on formation of defects, such as humping and undercuts, in non-vacuum electron beam welding was investigated. The influence of separate welding parameters on the quality of welds was determined.},
  language  = {en}
}
@inproceedings{FeldmannPyschnyDoeringetal.2012,
  author    = {Feldmann, Markus and Pyschny, D. and D{\"o}ring, Bernd and Kuhnhenne, Markus},
  title     = {Life cycle assessment of steel constructions},
  series = {Life-cycle and sustainability of civil infrastructure systems : proceedings of the Third International Symposium on Life-Cycle Civil Engineering (IALCCE'12) : Vienna, Austria, October 3-6, 2012},
  booktitle = {Life-cycle and sustainability of civil infrastructure systems : proceedings of the Third International Symposium on Life-Cycle Civil Engineering (IALCCE'12) : Vienna, Austria, October 3-6, 2012},
  publisher = {Taylor and Francis},
  address   = {Hoboken},
  organization    = {International Symposium on Life-Cycle Civil Engineering <3, 2012, Wien>},
  isbn      = {978-0-203-10336-4},
  pages     = {321},
  year      = {2012},
  language  = {en}
}