@inproceedings{SchopenKemperEsch2021,
  author    = {Schopen, Oliver and Kemper, Hans and Esch, Thomas},
  title     = {Development of a comparison methodology and evaluation matrix for electrically driven compressors in ICE and FC},
  series = {Proceedings of the 1st UNITED - Southeast Asia Automotive Interest Group (SAIG) International Conference},
  booktitle = {Proceedings of the 1st UNITED - Southeast Asia Automotive Interest Group (SAIG) International Conference},
  publisher = {FH Joanneum},
  address   = {Graz},
  isbn      = {978-3-902103-94-9},
  pages     = {45 -- 46},
  year      = {2021},
  abstract  = {In addition to electromobility and alternative drive systems, a focus is set on electrically driven compressors (EDC), with a high potential for increasing the efficiency of internal combustion engines (ICE) and fuel cells [01]. The primary objective is to increase the ICE torque, provided independently of the ICE speed by compressing the intake air and consequently the ICE filling level supported by the compressor. For operation independent from the ICE speed, the EDC compressor is decoupled from the turbine by using an electric compressor motor (CM) instead of the turbine. ICE performances can be increased by the use of EDC where individual compressor parameters are adapted to the respective application area [02] [03]. This task contains great challenges, increased by demands with regard to pollutant reduction while maintaining constant performance and reduced fuel consumption. The FH-Aachen is equipped with an EDC test bench which enables EDC-investigations in various configurations and operating modes. Characteristic properties of different compressors can be determined, which build the basis for a comparison methodology. Subject of this project is the development of a comparison methodology for EDC with an associated evaluation method and a defined overall evaluation method. For the application of this comparison methodology, corresponding series of measurements are carried out on the EDC test bench using an appropriate test device.},
  language  = {en}
}
@inproceedings{HauggKreyerKemperetal.2020,
  author    = {Haugg, Albert Thomas and Kreyer, J{\"o}rg and Kemper, Hans and Hatesuer, Katerina and Esch, Thomas},
  title     = {Heat exchanger for ORC. adaptability and optimisation potentials},
  series = {IIR International Rankine 2020 Conference},
  booktitle = {IIR International Rankine 2020 Conference},
  doi       = {10.18462/iir.rankine.2020.1224},
  pages     = {10 Seiten},
  year      = {2020},
  abstract  = {The recovery of waste heat requires heat exchangers to extract it from a liquid or gaseous medium into another working medium, a refrigerant. In Organic Rankine Cycles (ORC) on Combustion Engines there are two major heat sources, the exhaust gas and the water/glycol fluid from the engine's cooling circuit. A heat exchanger design must be adapted to the different requirements and conditions resulting from the heat sources, fluids, system configurations, geometric restrictions, and etcetera. The Stacked Shell Cooler (SSC) is a new and very specific design of a plate heat exchanger, created by AKG, which allows with a maximum degree of freedom the optimization of heat exchange rate and the reduction of the related pressure drop. This optimization in heat exchanger design for ORC systems is even more important, because it reduces the energy consumption of the system and therefore maximizes the increase in overall efficiency of the engine.},
  language  = {en}
}
@inproceedings{SchopenShabaniEschetal.2022,
  author    = {Schopen, Oliver and Shabani, Bahman and Esch, Thomas and Kemper, Hans and Shah, Neel},
  title     = {Quantitative evaluation of health management designs for fuel cell systems in transport vehicles},
  series = {2nd UNITED-SAIG International Conference Proceedings},
  booktitle = {2nd UNITED-SAIG International Conference Proceedings},
  editor    = {Rahim, S.A. and As'arry, A. and Zuhri, M.Y.M. and Harmin, M.Y. and Rezali, K.A.M. and Hairuddin, A.A.},
  pages     = {1 -- 3},
  year      = {2022},
  abstract  = {Focusing on transport vehicles, mainly with regard to aviation applications, this paper presents compilation and subsequent quantitative evaluation of methods aimed at building an optimum integrated health management solution for fuel cell systems. The methods are divided into two different main types and compiled in a related scheme. Furthermore, different methods are analysed and evaluated based on parameters specific to the aviation context of this study. Finally, the most suitable method for use in fuel cell health management systems is identified and its performance and suitability is quantified.},
  language  = {en}
}