@article{HoffstadtCheenakulaNikolauszetal.2023,
  author    = {Hoffstadt, Kevin and Cheenakula, Dheeraja and Nikolausz, Marcell and Krafft, Simone and Harms, Hauke and Kuperjans, Isabel},
  title     = {Design and construction of a new reactor for flexible biomethanation of hydrogen},
  series = {Fermentation},
  volume    = {9},
  journal   = {Fermentation},
  number    = {8},
  publisher = {MDPI},
  address   = {Basel},
  issn      = {2311-5637},
  doi       = {10.3390/fermentation9080774},
  pages     = {1 -- 16},
  year      = {2023},
  abstract  = {The increasing share of renewable electricity in the grid drives the need for sufficient storage capacity. Especially for seasonal storage, power-to-gas can be a promising approach. Biologically produced methane from hydrogen produced from surplus electricity can be used to substitute natural gas in the existing infrastructure. Current reactor types are not or are poorly optimized for flexible methanation. Therefore, this work proposes a new reactor type with a plug flow reactor (PFR) design. Simulations in COMSOL Multiphysics ® showed promising properties for operation in laminar flow. An experiment was conducted to support the simulation results and to determine the gas fraction of the novel reactor, which was measured to be 29\%. Based on these simulations and experimental results, the reactor was constructed as a 14 m long, 50 mm diameter tube with a meandering orientation. Data processing was established, and a step experiment was performed. In addition, a kLa of 1 h-1 was determined. The results revealed that the experimental outcomes of the type of flow and gas fractions are in line with the theoretical simulation. The new design shows promising properties for flexible methanation and will be tested.},
  language  = {en}
}
@article{CheenakulaHoffstadtKrafftetal.2022,
  author    = {Cheenakula, Dheeraja and Hoffstadt, Kevin and Krafft, Simone and Reinecke, Diana and Klose, Holger and Kuperjans, Isabel and Gr{\"o}mping, Markus},
  title     = {Anaerobic digestion of algal-bacterial biomass of an Algal Turf Scrubber system},
  series = {Biomass Conversion and Biorefinery},
  volume    = {13},
  journal   = {Biomass Conversion and Biorefinery},
  publisher = {Springer},
  address   = {Berlin},
  issn      = {2190-6823},
  doi       = {10.1007/s13399-022-03236-z},
  pages     = {15 Seiten},
  year      = {2022},
  abstract  = {This study investigated the anaerobic digestion of an algal-bacterial biofilm grown in artificial wastewater in an Algal Turf Scrubber (ATS). The ATS system was located in a greenhouse (50°54′19ʺN, 6°24′55ʺE, Germany) and was exposed to seasonal conditions during the experiment period. The methane (CH4) potential of untreated algal-bacterial biofilm (UAB) and thermally pretreated biofilm (PAB) using different microbial inocula was determined by anaerobic batch fermentation. Methane productivity of UAB differed significantly between microbial inocula of digested wastepaper, a mixture of manure and maize silage, anaerobic sewage sludge, and percolated green waste. UAB using sewage sludge as inoculum showed the highest methane productivity. The share of methane in biogas was dependent on inoculum. Using PAB, a strong positive impact on methane productivity was identified for the digested wastepaper (116.4\%) and a mixture of manure and maize silage (107.4\%) inocula. By contrast, the methane yield was significantly reduced for the digested anaerobic sewage sludge (50.6\%) and percolated green waste (43.5\%) inocula. To further evaluate the potential of algal-bacterial biofilm for biogas production in wastewater treatment and biogas plants in a circular bioeconomy, scale-up calculations were conducted. It was found that a 0.116 km2 ATS would be required in an average municipal wastewater treatment plant which can be viewed as problematic in terms of space consumption. However, a substantial amount of energy surplus (4.7-12.5 MWh a-1) can be gained through the addition of algal-bacterial biomass to the anaerobic digester of a municipal wastewater treatment plant. Wastewater treatment and subsequent energy production through algae show dominancy over conventional technologies.},
  language  = {en}
}
@inproceedings{HandschuhStollenwerkBorchert2021,
  author    = {Handschuh, Nils and Stollenwerk, Dominik and Borchert, J{\"o}rg},
  title     = {Operation of thermal storage power plants under high renewable grid penetration},
  series = {NEIS 2021: Conference on Sustainable Energy Supply and Energy Storage Systems},
  booktitle = {NEIS 2021: Conference on Sustainable Energy Supply and Energy Storage Systems},
  publisher = {VDE Verlag},
  address   = {Berlin},
  isbn      = {978-3-8007-5651-3},
  pages     = {261 -- 265},
  year      = {2021},
  abstract  = {The planned coal phase-out in Germany by 2038 will lead to the dismantling of power plants with a total capacity of approx. 30 GW. A possible further use of these assets is the conversion of the power plants to thermal storage power plants; the use of these power plants on the day-ahead market is considerably limited by their technical parameters. In this paper, the influence of the technical boundary conditions on the operating times of these storage facilities is presented. For this purpose, the storage power plants were described as an MILP problem and two price curves, one from 2015 with a relatively low renewable penetration (33 \%) and one from 2020 with a high renewable energy penetration (51 \%) are compared. The operating times were examined as a function of the technical parameters and the critical influencing factors were investigated. The thermal storage power plant operation duration and the energy shifted with the price curve of 2020 increases by more than 25 \% compared to 2015.},
  language  = {en}
}
@incollection{StollenwerkFranzkeMaureretal.2023,
  author    = {Stollenwerk, Dominik and Franzke, Till and Maurer, Florian and Reinkensmeier, Sebastian and Kim, Franken and Tambornino, Philipp and Haas, Florian and Rieke, Christian and Hermanuz, Andreas and Borchert, J{\"o}rg and Ritz, Thomas and Sander, Volker},
  title     = {Smarte Lades{\"a}ulen : Netz- und Marktdienliches {\"o}ffentliches Laden},
  series = {Towards the New Normal in Mobility : Technische und betriebswirtschaftliche Aspekte},
  booktitle = {Towards the New Normal in Mobility : Technische und betriebswirtschaftliche Aspekte},
  editor    = {Proff, Heike},
  publisher = {Springer Gabler},
  address   = {Wiesbaden},
  isbn      = {978-3-658-39437-0 (Print)},
  doi       = {10.1007/978-3-658-39438-7_18},
  pages     = {287 -- 304},
  year      = {2023},
  abstract  = {Stand 01.01.2022 sind in Deutschland 618.460 elektrisch angetriebene KFZ zugelassen. Insgesamt sind derzeit 48.540.878 KFZ zugelassen, was einer Elektromobilit{\"a}tsquote von ca. 1,2 \% entspricht. Derzeit werden Elektromobile {\"u}ber Ladestationen oder Steckdosen mit dem Stromnetz verbunden und {\"u}blicherweise mit der vollen Ladekapazit{\"a}t des Anschlusses aufgeladen, bis das Batteriemanagementsystem des Fahrzeugs abh{\"a}ngig vom Ladezustand der Batterie die Ladeleistung reduziert.},
  language  = {de}
}
@article{JablonowskiKollmannNabeletal.2016,
  author    = {Jablonowski, Nicolai David and Kollmann, Tobias and Nabel, Moritz and Damm, Tatjana and Klose, Holger and M{\"u}ller, Michael and Bl{\"a}sing, Marc and Seebold, S{\"o}ren and Krafft, Simone and Kuperjans, Isabel and Dahmen, Markus and Schurr, Ulrich},
  title     = {Valorization of Sida (Sida hermaphrodita) biomass for multiple energy purposes},
  series = {GCB [Global Change Biology] Bioenergy},
  volume    = {9},
  journal   = {GCB [Global Change Biology] Bioenergy},
  number    = {1},
  publisher = {Wiley-VCH},
  address   = {Weinheim},
  issn      = {1757-1707 (online)},
  doi       = {10.1111/gcbb.12346},
  pages     = {202 -- 214},
  year      = {2016},
  abstract  = {The performance and biomass yield of the perennial energy plant Sida hermaphrodita (hereafter referred to as Sida) as a feedstock for biogas and solid fuel was evaluated throughout one entire growing period at agricultural field conditions. A Sida plant development code was established to allow comparison of the plant growth stages and biomass composition. Four scenarios were evaluated to determine the use of Sida biomass with regard to plant development and harvest time: (i) one harvest for solid fuel only; (ii) one harvest for biogas production only; (iii) one harvest for biogas production, followed by a harvest of the regrown biomass for solid fuel; and (iv) two consecutive harvests for biogas production. To determine Sida's value as a feedstock for combustion, we assessed the caloric value, the ash quality, and melting point with regard to DIN EN ISO norms. The results showed highest total dry biomass yields of max. 25 t ha⁻¹, whereas the highest dry matter of 70\% to 80\% was obtained at the end of the growing period. Scenario (i) clearly indicated the highest energy recovery, accounting for 439 288 MJ ha⁻¹; the energy recovery of the four scenarios from highest to lowest followed this order: (i) ≫ (iii) ≫ (iv) > (ii). Analysis of the Sida ashes showed a high melting point of >1500 °C, associated with a net calorific value of 16.5-17.2 MJ kg⁻¹. All prerequisites for DIN EN ISO norms were achieved, indicating Sida's advantage as a solid energy carrier without any post-treatment after harvesting. Cell wall analysis of the stems showed a constant lignin content after sampling week 16 (July), whereas cellulose had already reached a plateau in sampling week 4 (April). The results highlight Sida as a promising woody, perennial plant, providing biomass for flexible and multipurpose energy applications.},
  language  = {en}
}
@inproceedings{RuppKuperjansSchulze2016,
  author    = {Rupp, Matthias and Kuperjans, Isabel and Schulze, Sven},
  title     = {Energetische und {\"o}kologische Bewertung hybrider Antriebe im st{\"a}dtischen Busverkehr},
  series = {Commercial vehicle technology 2016 : proceedings of the 4th Commercial Vehicle Technology Symposium (CVT 2016), March 8-10, 2016, University of Kaiserslautern, Kaiserslautern, Germany},
  booktitle = {Commercial vehicle technology 2016 : proceedings of the 4th Commercial Vehicle Technology Symposium (CVT 2016), March 8-10, 2016, University of Kaiserslautern, Kaiserslautern, Germany},
  editor    = {Berns, Karsten},
  publisher = {Shaker},
  address   = {Aachen},
  organization    = {Internationales Commercial Vehicle Technology Symposium <4, 2016, Kaiserslautern>},
  pages     = {227 -- 237},
  year      = {2016},
  abstract  = {In Anbetracht weltweit zunehmend strengerer klimapolitischer Ziele steigt auch der Druck f{\"u}r Nutzfahrzeughersteller, effizientere und umweltfreundlichere Technologien zu entwickeln. Den Blick bei der Bewertung dieser ausschließlich auf die Fahrzeugnutzung zu richten, ist l{\"a}ngst nicht mehr zufriedenstellend. Im Rahmen dieser Analyse wird ein gegenw{\"a}rtig auf dem Markt erwerblicher und in deutschen St{\"a}dten bereits seit Jahren betriebener Hybridbus energetisch und {\"o}kologisch mit einem konventionell angetriebenen, nahezu baugleichen Modell entlang des Lebensweges bewertet. Nach Definition von Ziel und Untersuchungsrahmen wird ein {\"U}berblick auf bereits durchgef{\"u}hrte Lebenszyklusanalysen zu Hybridbussen im Stadtverkehr gegeben und Schlussfolgerungen f{\"u}r die anschließende Analyse abgeleitet. Diese wird im Rahmen einer energetischen und {\"o}kologischen Bewertung beider Produktsysteme anhand der Parameter "Prim{\"a}renergieeinsatz" und "CO2{\"a}q Emissionen" praktiziert. Der Fahrzeugrumpf beider Fahrzeuge des gleichen Modells wird dabei als einheitlich angenommen, sodass bei dem Vergleich der Herstellung vereinfacht nur die sich unterscheidenden Komponenten des Antriebstranges ber{\"u}cksichtigt werden. Die Resultate der Wirkungsabsch{\"a}tzung werden als Differenz des Hybridbusses gegen{\"u}ber dem Referenzfahrzeug {\"u}ber die einzelnen Lebenszyklusphasen dargestellt. Schließlich werden Prognosen getroffen, ab welcher Strecke die bei der Herstellung erzeugten h{\"o}heren CO2{\"a}q Emissionen des Hybridantriebstranges gegen{\"u}ber dem Referenzmodell ausgeglichen werden.},
  language  = {de}
}
@incollection{BorchertRothe2016,
  author    = {Borchert, J{\"o}rg and Rothe, Sebastian},
  title     = {Energiemanagement und Versorgung von Chemieparks - Ein Ansatz zur wertsch{\"o}pfungsgetriebenen Risikosteuerung},
  series = {Chemiestandorte : Markt, Herausforderungen und Gesch{\"a}ftsmodelle},
  booktitle = {Chemiestandorte : Markt, Herausforderungen und Gesch{\"a}ftsmodelle},
  editor    = {Suntrop, Carsten},
  publisher = {Wiley-VCH},
  address   = {Weinheim},
  isbn      = {978-3-527-33441-4},
  pages     = {193 -- 210},
  year      = {2016},
  language  = {de}
}
@book{Pieper2019,
  author    = {Pieper, Martin},
  title     = {Quantenmechanik : Einf{\"u}hrung in die mathematische Formulierung},
  publisher = {Springer Spektrum},
  address   = {Wiesbaden},
  isbn      = {978-3-658-28329-2},
  doi       = {10.1007/978-3-658-28329-2},
  year      = {2019},
  language  = {de}
}
@book{Pieper2019,
  author    = {Pieper, Martin},
  title     = {Quantenmechanik: Einf{\"u}hrung in die mathematische Formulierung},
  publisher = {Springer Spektrum},
  address   = {Wiesbaden},
  isbn      = {978-3-658-28328-5},
  doi       = {10.1007/978-3-658-28329-2},
  pages     = {XI, 33 Seiten},
  year      = {2019},
  language  = {de}
}
@article{RiekeStollenwerkDahmenetal.2018,
  author    = {Rieke, Christian and Stollenwerk, Dominik and Dahmen, Markus and Pieper, Martin},
  title     = {Modeling and optimization of a biogas plant for a demand-driven energy supply},
  series = {Energy},
  volume    = {145},
  journal   = {Energy},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {0360-5442},
  doi       = {10.1016/j.energy.2017.12.073},
  pages     = {657 -- 664},
  year      = {2018},
  abstract  = {Due to the Renewable Energy Act, in Germany it is planned to increase the amount of renewable energy carriers up to 60\%. One of the main problems is the fluctuating supply of wind and solar energy. Here biogas plants provide a solution, because a demand-driven supply is possible. Before running such a plant, it is necessary to simulate and optimize the process. This paper provides a new model of a biogas plant, which is as accurate as the standard ADM1 model. The advantage compared to ADM1 is that it is based on only four parameters compared to 28. Applying this model, an optimization was installed, which allows a demand-driven supply by biogas plants. Finally the results are confirmed by several experiments and measurements with a real test plant.},
  language  = {en}
}