@article{FingerGoetten2019,
  author    = {Finger, Felix and G{\"o}tten, Falk},
  title     = {Neue Ans{\"a}tze f{\"u}r die Entwicklung von unbemannten Flugger{\"a}ten},
  series = {Ingenieurspiegel},
  volume    = {2019},
  journal   = {Ingenieurspiegel},
  number    = {1},
  isbn      = {1868-5919},
  pages     = {67 -- 68},
  year      = {2019},
  abstract  = {Wie sieht das unbemannte Flugzeug von {\"U}bermorgen aus? Dieser Frage stellen sich Forscher an der Fachhochschule Aachen. Die weltweit rasant fortschreitende Entwicklung des Marktes f{\"u}r unbemannte Flugger{\"a}te (UAVs - „Unmanned Aerial Vehicles") bietet großes Potenzial f{\"u}r Wachstum und Wertsch{\"o}pfung. Unbemannte fliegende Systeme k{\"o}nnen - f{\"u}r bestimmte Anwendungsgebiete - wesentlich g{\"u}nstiger, kleiner und effizienter ausgelegt werden als bemannte L{\"o}sungen. Dabei sind sich viele Unternehmen {\"u}ber das m{\"o}gliche Potential dieser Technologie noch gar nicht bewusst.},
  language  = {de}
}
@inproceedings{BergmannGraebenerWildetal.2019,
  author    = {Bergmann, Kevin and Gr{\"a}bener, Josefine and Wild, Dominik and Ulfers, H. and Czupalla, Markus},
  title     = {Study on thermal stabilization of a GEO-stationary telescope baffling system by integral application of phase change material},
  series = {International Conference on Environmental Systems},
  booktitle = {International Conference on Environmental Systems},
  pages     = {1 -- 14},
  year      = {2019},
  abstract  = {The utilization of phase change material (PCM) for latent heat storage and thermal control of spacecraft has been demonstrated in the past in few missions only. One limiting factor was the fact that all concepts developed so far envisioned the PCM to be applied as an additional capacitor, encapsulated in its own housing, leading to mass, efficiency and accommodation challenges. Recently, the application of PCM within the scan cavity of a GEOS type satellite has been suggested, in order to tackle thermal issues due to direct sun intrusion (Choi, M., 2014). However, the application of PCM in such complex mechanical structures is extremely challenging. A new concept to tackle this issue is currently under development at the FH Aachen University of Applied Sciences. The concept "Infused Thermal Solutions (ITS)" is based on the idea to 3D print metallic structures in their regular functional shape, but double walled with internal lattice support structures, allowing the infusion of a PCM layer directly into the voids and eliminating the need for additional parts and interfaces. Together with OHB System, FH Aachen theoretically studied the application of this technology to the Meteosat Third Generation (MTG) Infra-Red Sounder (IRS) instrument. The study focuses on the scan cavity and entrance baffling assembly (EBA) of the IRS. It consists of thermal analyses, 3D-redesign and bread boarding of a scaled and PCM infused EBA version. In the thermal design of the alternative EBA, PCM was applied directly into the EBA, simulating the worst hot case sun intrusion of the mission. By applying 4kg of PCM (to a 60kg baffle) the EBA temperature excursions during sun intrusion were limited from 140K to 30K, leading to a significant thermo-opto-elastic performance gain. This paper introduces the ITS concept development status.},
  language  = {en}
}
@phdthesis{Beckmann2019,
  author    = {Beckmann, Nils},
  title     = {Characterization of the hydrogen-dry-low-Nox-micromix-combustion-principle for hydrogen-methane fuel mixtures},
  publisher = {RMIT University},
  address   = {Melbourne},
  pages     = {XV, 160 Seiten},
  year      = {2019},
  language  = {en}
}
@article{GoettscheAlexopoulosDuemmleretal.2019,
  author    = {G{\"o}ttsche, Joachim and Alexopoulos, Spiros and D{\"u}mmler, Andreas and Maddineni, S. K.},
  title     = {Multi-Mirror Array Calculations With Optical Error},
  pages     = {1 -- 6},
  year      = {2019},
  abstract  = {The optical performance of a 2-axis solar concentrator was simulated with the COMSOL Multiphysics® software. The concentrator consists of a mirror array, which was created using the application builder. The mirror facets are preconfigured to form a focal point. During tracking all mirrors are moved simultaneously in a coupled mode by 2 motors in two axes, in order to keep the system in focus with the moving sun. Optical errors on each reflecting surface were implemented in combination with the solar angular cone of ± 4.65 mrad. As a result, the intercept factor of solar radiation that is available to the receiver was calculated as a function of the transversal and longitudinal angles of incidence. In addition, the intensity distribution on the receiver plane was calculated as a function of the incidence angles.},
  language  = {en}
}
@book{Schmidt2019,
  author    = {Schmidt, Bernd},
  title     = {Grundlagen der Elektrotechnik und Elektronik f{\"u}r Ingenieure der Schienenfahrzeugtechnik und anderer Fachrichtungen : neu mit neuem SI-System und weiteren Inhalten f{\"u}r Mechantroniker},
  edition   = {3. vollst{\"a}ndig {\"u}berarbeitete Auflage},
  publisher = {B. Schmidt, Fachverlag f{\"u}r Elektro- und Informationstechnik},
  address   = {Bielefeld},
  isbn      = {978-3-944131-04-7},
  pages     = {XXVI, 270 Seiten : Illustrationen, Diagramme},
  year      = {2019},
  language  = {de}
}
@inproceedings{MarinkovićButenweg2019,
  author    = {Marinković, Marko and Butenweg, Christoph},
  title     = {Experimental and numerical analysis of RC frames with decoupled masonry infills},
  series = {7th ECCOMAS Thematic Conference on Computational Methods in Structural Dynamics and Earthquake Engineering},
  booktitle = {7th ECCOMAS Thematic Conference on Computational Methods in Structural Dynamics and Earthquake Engineering},
  editor    = {Papadrakakis, Manolis and Fragiadakis, Michalis},
  publisher = {National Technical University of Athens},
  address   = {Athen},
  isbn      = {978-618-82844-5-6},
  issn      = {2623-3347},
  doi       = {10.7712/120119.7088.18845},
  pages     = {2464 -- 2479},
  year      = {2019},
  abstract  = {Masonry infill walls are commonly used in reinforced concrete (RC) frame structures, also in seismically active areas, although they often experience serious damage during earthquakes. One of the main reasons for their poor behaviour is the connection to the frame, which is usually constructed using mortar. This paper describes the novel solution for infill/frame connection based on application of elastomeric material between them. The system called INODIS (Innovative Decoupled Infill System) has the aim to postpone the activation of infill in in-plane direction and at the same time to provide sufficient out-of-plane support. First, experimental tests on infilled frame specimens are presented and the comparison of the results between traditionally infilled frames and infilled frames with the INODIS system are given. The results are then used for calibration and validation of numerical model, which can be further employed for investigating the influence of some material parameters on the behaviour of infilled frames with the INODIS system.},
  language  = {en}
}
@inproceedings{MichelAlderButenwegetal.2019,
  author    = {Michel, Philipp and Alder, Philipp and Butenweg, Christoph and Klinkel, Sven},
  title     = {Berechnung der Fluid-Struktur-Interaktion f{\"u}r flexibel gelagerte Fl{\"u}ssigkeitstanks},
  series = {16. D-A-CH Tagung Erdbebeningenieurwesen \& Baudynamik: 26. und 27. September 2019, Universit{\"a}t Innsbruck},
  booktitle = {16. D-A-CH Tagung Erdbebeningenieurwesen \& Baudynamik: 26. und 27. September 2019, Universit{\"a}t Innsbruck},
  isbn      = {978-3-200-06454-6},
  year      = {2019},
  language  = {de}
}
@article{BaringhausGaigall2019,
  author    = {Baringhaus, Ludwig and Gaigall, Daniel},
  title     = {On an asymptotic relative efficiency concept based on expected volumes of confidence regions},
  series = {Statistics - A Journal of Theoretical and Applied Statistic},
  volume    = {53},
  journal   = {Statistics - A Journal of Theoretical and Applied Statistic},
  number    = {6},
  publisher = {Taylor \& Francis},
  address   = {London},
  issn      = {1029-4910},
  doi       = {10.1080/02331888.2019.1683560},
  pages     = {1396 -- 1436},
  year      = {2019},
  abstract  = {The paper deals with an asymptotic relative efficiency concept for confidence regions of multidimensional parameters that is based on the expected volumes of the confidence regions. Under standard conditions the asymptotic relative efficiencies of confidence regions are seen to be certain powers of the ratio of the limits of the expected volumes. These limits are explicitly derived for confidence regions associated with certain plugin estimators, likelihood ratio tests and Wald tests. Under regularity conditions, the asymptotic relative efficiency of each of these procedures with respect to each one of its competitors is equal to 1. The results are applied to multivariate normal distributions and multinomial distributions in a fairly general setting.},
  language  = {en}
}
@article{Gaigall2019,
  author    = {Gaigall, Daniel},
  title     = {On a new approach to the multi-sample goodness-of-fit problem},
  series = {Communications in Statistics - Simulation and Computation},
  volume    = {53},
  journal   = {Communications in Statistics - Simulation and Computation},
  number    = {10},
  publisher = {Taylor \& Francis},
  address   = {London},
  issn      = {1532-4141},
  doi       = {10.1080/03610918.2019.1618472},
  pages     = {2971 -- 2989},
  year      = {2019},
  abstract  = {Suppose we have k samples X₁,₁,…,X₁,ₙ₁,…,Xₖ,₁,…,Xₖ,ₙₖ with different sample sizes ₙ₁,…,ₙₖ and unknown underlying distribution functions F₁,…,Fₖ as observations plus k families of distribution functions {G₁(⋅,ϑ);ϑ∈Θ},…,{Gₖ(⋅,ϑ);ϑ∈Θ}, each indexed by elements ϑ from the same parameter set Θ, we consider the new goodness-of-fit problem whether or not (F₁,…,Fₖ) belongs to the parametric family {(G₁(⋅,ϑ),…,Gₖ(⋅,ϑ));ϑ∈Θ}. New test statistics are presented and a parametric bootstrap procedure for the approximation of the unknown null distributions is discussed. Under regularity assumptions, it is proved that the approximation works asymptotically, and the limiting distributions of the test statistics in the null hypothesis case are determined. Simulation studies investigate the quality of the new approach for small and moderate sample sizes. Applications to real-data sets illustrate how the idea can be used for verifying model assumptions.},
  language  = {en}
}
@misc{OPUS4-10942,
  title     = {2. Ordnung zur {\"A}nderung der Beitragsordnung der Studierendenschaft der Fachhochschule Aachen : vom 7. November 2019},
  organization    = {FH Aachen},
  pages     = {2 Seiten},
  year      = {2019},
  language  = {de}
}