@article{SchoppRohrbachLangeretal.2024, author = {Schopp, Christoph and Rohrbach, Felix and Langer, Luc and Heuermann, Holger}, title = {Detection of welding wire length by active S11 measurement}, series = {IEEE Transactions on Plasma Science}, journal = {IEEE Transactions on Plasma Science}, number = {Early Access}, publisher = {IEEE}, issn = {0093-3813 (Print)}, doi = {10.1109/TPS.2024.3356659}, pages = {1 -- 6}, year = {2024}, abstract = {A novel method to determine the extruded length of a metallic wire for a directed energy deposition (DED) process using a microwave (MW) plasma jet with a straight-through wire feed is presented. The method is based on the relative comparison of the measured frequency response obtained by the large-signal scattering parameter (Hot-S) technique. In the practical working range, repeatability of less than 6\% for a nonactive plasma and 9\% for the active plasma state is found. Measurements are conducted with a focus on a simple solution to decrease the processing time and reduce the integration time of the process into the existing hardware. It is shown that monitoring a single frequency for magnitude and phase changes is sufficient to achieve good accuracy. A combination of different measurement values to determine the length is possible. The applicability to different diameter of the same material is shown as well as a contact detection of the wire and metallic substrate.}, language = {en} } @article{BoehnischBraunMuscarelloetal.2024, author = {B{\"o}hnisch, Nils and Braun, Carsten and Muscarello, Vincenzo and Marzocca, Pier}, title = {About the wing and whirl flutter of a slender wing-propeller system}, series = {Journal of Aircraft}, journal = {Journal of Aircraft}, publisher = {AIAA}, address = {Reston, Va.}, issn = {1533-3868}, doi = {10.2514/1.C037542}, pages = {1 -- 14}, year = {2024}, abstract = {Next-generation aircraft designs often incorporate multiple large propellers attached along the wingspan (distributed electric propulsion), leading to highly flexible dynamic systems that can exhibit aeroelastic instabilities. This paper introduces a validated methodology to investigate the aeroelastic instabilities of wing-propeller systems and to understand the dynamic mechanism leading to wing and whirl flutter and transition from one to the other. Factors such as nacelle positions along the wing span and chord and its propulsion system mounting stiffness are considered. Additionally, preliminary design guidelines are proposed for flutter-free wing-propeller systems applicable to novel aircraft designs. The study demonstrates how the critical speed of the wing-propeller systems is influenced by the mounting stiffness and propeller position. Weak mounting stiffnesses result in whirl flutter, while hard mounting stiffnesses lead to wing flutter. For the latter, the position of the propeller along the wing span may change the wing mode shapes and thus the flutter mechanism. Propeller positions closer to the wing tip enhance stability, but pusher configurations are more critical due to the mass distribution behind the elastic axis.}, language = {en} } @article{TurdumamatovBeldaHeuermann2024, author = {Turdumamatov, Samat and Belda, Aljoscha and Heuermann, Holger}, title = {Shaping a decoupled atmospheric pressure microwave plasma with antenna structures, Maxwell's equations, and boundary conditions}, series = {IEEE Transactions on Plasma Science}, journal = {IEEE Transactions on Plasma Science}, number = {Early Access}, publisher = {IEEE}, issn = {0093-3813 (Print)}, doi = {10.1109/TPS.2024.3383589}, pages = {1 -- 9}, year = {2024}, abstract = {This article addresses the need for an innovative technique in plasma shaping, utilizing antenna structures, Maxwell's laws, and boundary conditions within a shielded environment. The motivation lies in exploring a novel approach to efficiently generate high-energy density plasma with potential applications across various fields. Implemented in an E01 circular cavity resonator, the proposed method involves the use of an impedance and field matching device with a coaxial connector and a specially optimized monopole antenna. This setup feeds a low-loss cavity resonator, resulting in a high-energy density air plasma with a surface temperature exceeding 3500 o C, achieved with a minimal power input of 80 W. The argon plasma, resembling the shape of a simple monopole antenna with modeled complex dielectric values, offers a more energy-efficient alternative compared to traditional, power-intensive plasma shaping methods. Simulations using a commercial electromagnetic (EM) solver validate the design's effectiveness, while experimental validation underscores the method's feasibility and practical implementation. Analyzing various parameters in an argon atmosphere, including hot S -parameters and plasma beam images, the results demonstrate the successful application of this technique, suggesting its potential in coating, furnace technology, fusion, and spectroscopy applications.}, language = {en} } @article{BlockViebahnJungbluth2024, author = {Block, Simon and Viebahn, Peter and Jungbluth, Christian}, title = {Analysing direct air capture for enabling negative emissions in Germany: an assessment of the resource requirements and costs of a potential rollout in 2045}, series = {Frontiers in Climate}, volume = {6}, journal = {Frontiers in Climate}, publisher = {Frontiers}, address = {Lausanne}, issn = {2624-9553}, doi = {10.3389/fclim.2024.1353939}, pages = {18 Seiten}, year = {2024}, abstract = {Direct air capture (DAC) combined with subsequent storage (DACCS) is discussed as one promising carbon dioxide removal option. The aim of this paper is to analyse and comparatively classify the resource consumption (land use, renewable energy and water) and costs of possible DAC implementation pathways for Germany. The paths are based on a selected, existing climate neutrality scenario that requires the removal of 20 Mt of carbon dioxide (CO2) per year by DACCS from 2045. The analysis focuses on the so-called "low-temperature" DAC process, which might be more advantageous for Germany than the "high-temperature" one. In four case studies, we examine potential sites in northern, central and southern Germany, thereby using the most suitable renewable energies for electricity and heat generation. We show that the deployment of DAC results in large-scale land use and high energy needs. The land use in the range of 167-353 km2 results mainly from the area required for renewable energy generation. The total electrical energy demand of 14.4 TWh per year, of which 46\% is needed to operate heat pumps to supply the heat demand of the DAC process, corresponds to around 1.4\% of Germany's envisaged electricity demand in 2045. 20 Mt of water are provided yearly, corresponding to 40\% of the city of Cologne's water demand (1.1 million inhabitants). The capture of CO2 (DAC) incurs levelised costs of 125-138 EUR per tonne of CO2, whereby the provision of the required energy via photovoltaics in southern Germany represents the lowest value of the four case studies. This does not include the costs associated with balancing its volatility. Taking into account transporting the CO2 via pipeline to the port of Wilhelmshaven, followed by transporting and sequestering the CO2 in geological storage sites in the Norwegian North Sea (DACCS), the levelised costs increase to 161-176 EUR/tCO2. Due to the longer transport distances from southern and central Germany, a northern German site using wind turbines would be the most favourable.}, language = {en} } @masterthesis{Ackermann2024, type = {Bachelor Thesis}, author = {Ackermann, Vincent}, title = {Filos : Design eines Front-Ends f{\"u}r das robotergef{\"u}hrte Laser-Osteotom-System STELLA.}, publisher = {FH Aachen}, address = {Aachen}, pages = {70 Seiten}, year = {2024}, abstract = {In der Abschlussarbeit „FILOS" wurde in Zusammenarbeit mit dem Fraunhofer-Institut f{\"u}r Lasertechnik (ILT) ein Front-End f{\"u}r das laserbasierte Osteotom STELLA entwickelt. STELLA soll Kraniotomie (das Er{\"o}ffnen des Sch{\"a}dels) im wachen Zustand erm{\"o}glichen und erfordert eine benutzerfreundliche Bedienungsplattform sowie ein funktionales und {\"a}sthetisches Design. Das Ziel von „FILOS" war es, ein Geh{\"a}use zu entwerfen, das den medizinischen Anforderungen entspricht, und ein Bedienkonzept zu entwickeln, dass die Akzeptanz bei Patient:innen und Anwender:innen f{\"o}rdert. Durch Expert:innen-Interviews mit Neurochirurg:innen und enge Zusammenarbeit mit dem ILT wurde ein durchdachtes Design entwickelt. Dieses soll den Anforderungen der Anwender:innen gerecht werden, das zuk{\"u}nftige Operationssystem repr{\"a}sentieren und somit einen Mehrwert in der Medizin schaffen.}, language = {de} } @masterthesis{Bartz2024, type = {Bachelor Thesis}, author = {Bartz, Markus}, title = {Dupiano : Ein aus einem Bauelement auffaltbarer Keyboradst{\"a}nder mit dem Erscheinungsbild eines akustischen Klavieres.}, publisher = {FH Aachen}, address = {Aachen}, pages = {123 Seiten}, year = {2024}, abstract = {Klavierspielende K{\"u}nstlerinnen und K{\"u}nstler finden sich auf der B{\"u}hne meist an einer Kombination aus Keyboard und Keyboardst{\"a}nder wieder. Zwar kann der Klang eines Klaviers technisch brillant simuliert werden, jedoch verliert das B{\"u}hnenbild den Mehrwert eines traditionellen Klaviers. Um diesem Verlust von Authentizit{\"a}t und Wohlgef{\"u}hl auf der B{\"u}hne endlich etwas entgegenzusetzen, soll ein "dupiano" g{\"a}ngige Keyboardst{\"a}nder ersetzen und s{\"a}mtliche Keyboards in das Erscheinungsbild eines akustischen Klaviers h{\"u}llen. Dadurch sollen auch die visuellen Eindr{\"u}cke, verkn{\"u}pft mit den akustischen, an Authentizit{\"a}t gewinnen und den Klavierauftritt vervollst{\"a}ndigen. Es ist leicht, stabil und ohne Werkzeug in unter 10 Sekunden aufbaubar. Auch der Abbau geschieht in unter 10 Sekunden. Verstaut werden kann es von einer Person in jedem Kofferraum. "dupiano" - was nach Klavier klingt, soll auch so aussehen!}, language = {de} } @incollection{SchneiderWisselinkCzarneckietal.2024, author = {Schneider, Dominik and Wisselink, Frank and Czarnecki, Christian and N{\"o}lle, Nikolai}, title = {Benefits and framework conditions for information-driven business models concerning the Internet of Things}, series = {Digitalization in companies}, booktitle = {Digitalization in companies}, publisher = {Springer}, address = {Wiesbaden}, isbn = {978-3-658-39093-8 (Print)}, doi = {10.1007/978-3-658-39094-5_5}, pages = {59 -- 75}, year = {2024}, abstract = {In the context of the increasing digitalization, the Internet of Things (IoT) is seen as a technological driver through which completely new business models can emerge in the interaction of different players. Identified key players include traditional industrial companies, municipalities and telecommunications companies. The latter, by providing connectivity, ensure that small devices with tiny batteries can be connected almost anywhere and directly to the Internet. There are already many IoT use cases on the market that provide simplification for end users, such as Philips Hue Tap. In addition to business models based on connectivity, there is great potential for information-driven business models that can support or enhance existing business models. One example is the IoT use case Park and Joy, which uses sensors to connect parking spaces and inform drivers about available parking spaces in real time. Information-driven business models can be based on data generated in IoT use cases. For example, a telecommunications company can add value by deriving more decision-relevant information - called insights - from data that is used to increase decision agility. In addition, insights can be monetized. The monetization of insights can only be sustainable, if careful attention is taken and frameworks are considered. In this chapter, the concept of information-driven business models is explained and illustrated with the concrete use case Park and Joy. In addition, the benefits, risks and framework conditions are discussed.}, language = {en} } @masterthesis{Giernich2024, type = {Bachelor Thesis}, author = {Giernich, Marie}, title = {Zookunft: Zoo der Zukunft}, publisher = {FH Aachen}, address = {Aachen}, pages = {93 Seiten}, year = {2024}, abstract = {Inmitten globaler Natur- und Artenschutzherausforderungen ist die Transformation zoologischer Einrichtungen entscheidend. "Zookunft" pr{\"a}sentiert ein innovatives Konzept f{\"u}r ein Tropenhaus im K{\"o}lner Zoo, das Natur und Augmented Reality einzigartig verkn{\"u}pft. Ziel ist ein Raumkonzept, welches den Besucher:innen ein tiefes Verst{\"a}ndnis f{\"u}r die Fauna und Flora des s{\"u}dostasiatischen Regenwaldes vermitteln soll. Durch die geschickte Integration von Augmented Reality entsteht eine innovative Lern- und Erlebniswelt, die Umweltschutz- und Artenschutzbem{\"u}hungen unterst{\"u}tzt und nachhaltige Bildung f{\"o}rdert. Besuchende tauchen aktiv in die faszinierende Welt des Regenwaldes ein, wenn Natur und Augmented Reality eine immersive Umgebung schaffen. "Zookunft" soll als Vorreiter f{\"u}r Zooumgestaltungen dienen, Mensch und Natur verbinden und nachhaltige Bildung f{\"o}rdern. Ein Raum, der Naturerlebnisse und Technologie beeindruckend kombiniert.}, language = {de} } @incollection{Golland2024, author = {Golland, Alexander}, title = {Kommentierung von \S\S 6 bis 10 EKD-Datenschutzgesetz}, series = {EKD-Datenschutzgesetz. Datenschutzbestimmungen der evangelischen Kirche}, booktitle = {EKD-Datenschutzgesetz. Datenschutzbestimmungen der evangelischen Kirche}, editor = {Wagner, Ralph}, publisher = {Nomos}, address = {Baden-Baden}, isbn = {978-3-8487-8111-9}, pages = {153 -- 228}, year = {2024}, language = {de} } @techreport{BarnatArntzBerneckeretal.2024, type = {Working Paper}, author = {Barnat, Miriam and Arntz, Kristian and Bernecker, Andreas and Fissabre, Anke and Franken, Norbert and Goldbach, Daniel and H{\"u}ning, Felix and J{\"o}rissen, J{\"o}rg and Kirsch, Ansgar and Pettrak, J{\"u}rgen and Rexforth, Matthias and Josef, Rosenkranz and Terstegge, Andreas}, title = {Strategische Gestaltung von Studieng{\"a}ngen f{\"u}r die Zukunft: Ein kollaborativ entwickeltes Self-Assessment}, series = {Hochschulforum Digitalisierung - Diskussionspapier}, journal = {Hochschulforum Digitalisierung - Diskussionspapier}, publisher = {Stifterverband f{\"u}r die Deutsche Wissenschaft}, address = {Berlin}, issn = {2365-7081}, pages = {16 Seiten}, year = {2024}, abstract = {Das Diskussionspapier beschreibt einen Prozess an der FH Aachen zur Entwicklung und Implementierung eines Self-Assessment-Tools f{\"u}r Studieng{\"a}nge. Dieser Prozess zielte darauf ab, die Relevanz der Themen Digitalisierung, Internationalisierung und Nachhaltigkeit in Studieng{\"a}ngen zu st{\"a}rken. Durch Workshops und kollaborative Entwicklung mit Studiendekan:innen entstand ein Fragebogen, der zur Reflexion und strategischen Weiterentwicklung der Studieng{\"a}nge dient.}, language = {de} }