@article{Golland2020,
  author    = {Golland, Alexander},
  title     = {Weckruf f{\"u}r deutsche Großunternehmen? - Der neue Entwurf des IT-Sicherheitsgesetz 2.0},
  series = {K\&R Kommunikation \& Recht},
  volume    = {23},
  journal   = {K\&R Kommunikation \& Recht},
  number    = {7-8},
  publisher = {dfv Mediengruppe},
  address   = {Frankfurt a.M.},
  isbn      = {1434-6354},
  pages     = {I},
  year      = {2020},
  language  = {de}
}
@article{Olbertz2020,
  author    = {Olbertz, Klaus},
  title     = {Wenn der „leitende" Angestellte doch nur ein „normaler" Arbeitnehmer ist ... : Zur Rechtsstellung leitender Angestellter, zu Fehleinsch{\"a}tzungen des Arbeitgebers und Praxishinweisen},
  series = {NWB - Steuer- und Wirtschaftsrecht},
  journal   = {NWB - Steuer- und Wirtschaftsrecht},
  number    = {32},
  publisher = {NWB-Verl.},
  address   = {Herne},
  issn      = {0028-3460},
  pages     = {2397 -- 2406},
  year      = {2020},
  language  = {de}
}
@article{GoettenHavermannBraunetal.2020,
  author    = {G{\"o}tten, Falk and Havermann, Marc and Braun, Carsten and Marino, Matthew and Bil, Cees},
  title     = {Wind-tunnel and CFD investigations of UAV landing gears and turrets - Improvements in empirical drag estimation},
  series = {Aerospace Science and Technology},
  volume    = {107},
  journal   = {Aerospace Science and Technology},
  number    = {Art. 106306},
  publisher = {Elsevier},
  address   = {Amsterdam},
  issn      = {1270-9638},
  doi       = {10.1016/j.ast.2020.106306},
  year      = {2020},
  abstract  = {This paper analyzes the drag characteristics of several landing gear and turret configurations that are representative of unmanned aircraft tricycle landing gears and sensor turrets. A variety of these components were constructed via 3D-printing and analyzed in a wind-tunnel measurement campaign. Both turrets and landing gears were attached to a modular fuselage that supported both isolated components and multiple components at a time. Selected cases were numerically investigated with a Reynolds-averaged Navier-Stokes approach that showed good accuracy when compared to wind-tunnel data. The drag of main gear struts could be significantly reduced via streamlining their cross-sectional shape and keeping load carrying capabilities similar. The attachment of wheels introduced interference effects that increased strut drag moderately but significantly increased wheel drag compared to isolated cases. Very similar behavior was identified for front landing gears. The drag of an electro-optical and infrared sensor turret was found to be much higher than compared to available data of a clean hemisphere-cylinder combination. This turret drag was merely influenced by geometrical features like sensor surfaces and the rotational mechanism. The new data of this study is used to develop simple drag estimation recommendations for main and front landing gear struts and wheels as well as sensor turrets. These recommendations take geometrical considerations and interference effects into account.},
  language  = {en}
}
@article{HoevelerBauknechtWolfetal.2020,
  author    = {Hoeveler, B. and Bauknecht, Andr{\´e} and Wolf, C. Christian and Janser, Frank},
  title     = {Wind-Tunnel Study of a Wing-Embedded Lifting Fan Remaining Open in Cruise Flight},
  series = {Journal of Aircraft},
  volume    = {57},
  journal   = {Journal of Aircraft},
  number    = {4},
  publisher = {AIAA},
  address   = {Reston, Va.},
  issn      = {1533-3868},
  doi       = {10.2514/1.C035422},
  year      = {2020},
  abstract  = {It is investigated whether a nonrotating lifting fan remaining uncovered during cruise flight, as opposed to being covered by a shutter system, can be realized with limited additional drag and loss of lift during cruise flight. A wind-tunnel study of a wing-embedded lifting fan has been conducted at the Side Wind Test Facility G{\"o}ttingen of DLR, German Aerospace Center in G{\"o}ttingen using force, pressure, and stereoscopic particle image velocimetry techniques. The study showed that a step on the lower side of the wing in front of the lifting fan duct increases the lift-to-drag ratio of the whole model by up to 25\% for all positive angles of attack. Different sizes and inclinations of the step had limited influence on the surface pressure distribution. The data indicate that these parameters can be optimized to maximize the lift-to-drag ratio. A doubling of the curvature radius of the lifting fan duct inlet lip on the upper side of the wing affected the lift-to-drag ratio by less than 1\%. The lifting fan duct inlet curvature can therefore be optimized to maximize the vertical fan thrust of the rotating lifting fan during hovering without affecting the cruise flight performance with a nonrotating fan.},
  language  = {en}
}